CY7C09199-7AC

25/0251 CY7C09089/99 CY7C09189/99 64K/128K x 8/9 Synchronous Dual-Port Static RAM Features • True dual-ported memory cells which allow simultaneous access of the same memory location • Six Flow-Through/Pipelined devices — 64K x 8/9 organizations (CY7C09089/189) — 128K x 8/9 organizations (CY7C09099/199) • Three Modes — Flow-Through — Pipelined — Burst • Pipelined output mode on both ports allows fast 100MHz cycle time • 0.35-micron CMOS for optimum speed/power • High-speed clock to data access 6.5[1]/7.5/9/12 ns (max.) • Low operating power — Active = 195 mA (typical) — Standby = 0.05 mA (typical) • Fully synchronous interface for easier operation • Burst counters increment addresses internally — Shorten cycle times — Minimize bus noise • • • • • — Supported in Flow-Through and Pipelined modes Dual Chip Enables for easy depth expansion Automatic power-down Commercial and Industrial temperature ranges Available in 100-pin TQFP Pin-compatible and functionally equivalent to IDT70908 and IDT709089 Logic Block Diagram R/WL OEL R/WR OER CE0L CE1L 1 0/1 1 0/1 0 0 CE0R CE1R FT/PipeL [2] 0/1 1 0 0 1 0/1 FT/PipeR [2] 8/9 8/9 I/O0L–I/O7/8L I/O Control [3] I/O0R–I/O7/8R I/O Control 16/17 [3] 16/17 A0–A15/16L CLKL ADSL CNTENL CNTRSTL Counter/ Address Register Decode True Dual-Ported RAM Array Counter/ Address Register Decode A0–A15/16R CLKR ADSR CNTENR CNTRSTR Notes: 1. See page 7 for Load Conditions. 2. I/O0–I/O7 for x8 devices; I/O0–I/O8 for x9 devices. 3. A0–A15 for 64K; and A0–A16 for 128K devices. For the most recent information, visit the Cypress web site at www.cypress.com Cypress Semiconductor Corporation • 3901 North First Street • San Jose • CA 95134 • 408-943-2600 Document #: 38-06039 Rev. *A Revised December 27, 2002 CY7C09089/99 CY7C09189/99 Functional Description The CY7C09089/99 and CY7C09189/99 are high-speed synchronous CMOS 64K and 128K x 8/9 dual-port static RAMs. Two ports are provided, permitting independent, simultaneous access for reads and writes to any location in memory.[4] Registers on control, address, and data lines allow for minimal setup and hold times. In pipelined output mode, data is registered for decreased cycle time. Clock to data valid tCD2 = 6.5 ns[1] (pipelined). Flow-through mode can also be used to bypass the pipelined output register to eliminate access latency. In flow-through mode data will be available tCD1 = 15 ns after the address is clocked into the device. Pipelined output or flowthrough mode is selected via the FT/Pipe pin. Each port contains a burst counter on the input address register. The internal write pulse width is independent of the LOWto-HIGH transition of the clock signal. The internal write pulse is self-timed to allow the shortest possible cycle times. A HIGH on CE0 or LOW on CE1 for one clock cycle will power down the internal circuitry to reduce the static power consumption. The use of multiple Chip Enables allows easier banking of multiple chips for depth expansion configurations. In the pipelined mode, one cycle is required with CE0 LOW and CE1 HIGH to reactivate the outputs. Counter enable inputs are provided to stall the operation of the address input and utilize the internal address generated by the internal counter for fast interleaved memory applications. A port’s burst counter is loaded with the port’s Address Strobe (ADS). When the port’s Count Enable (CNTEN) is asserted, the address counter will increment on each LOW-to-HIGH transition of that port’s clock signal. This will read/write one word from/into each successive address location until CNTEN is deasserted. The counter can address the entire memory array and will loop back to the start. Counter Reset (CNTRST) is used to reset the burst counter. All parts are available in 100-pin Thin Quad Plastic Flatpack (TQFP) packages. Note: 4. When writing simultaneously to the same location, the final value cannot be guaranteed. Document #: 38-06039 Rev. *A Page 2 of 19 CY7C09089/99 CY7C09189/99 Pin Configurations 100-Pin TQFP (Top View) CNTENR CNTENL ADSR CLKR ADSL CLKL GND A0R A1R A2R A3R A4R A5R A6R A6L A5L A4L A3L A2L A1L A0L NC NC NC 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 NC NC A7L A8L A9L A10L A11L A12L A13L A14L A15L [5] A16L VCC NC NC NC NC CE0L CE1L CNTRSTL R/WL OEL [6] FT/PIPEL NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 75 74 73 72 71 70 69 68 67 66 NC NC A7R A8R A9R A10R A11R A12R A13R A14R A15R A16R GND NC NC NC NC CE0R CE1R CNTRSTR R/WR OER FT/PIPER GND NC [6] [5] CY7C09099 (128K x 8) CY7C09089 (64K x 8) NC 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 NC I/01R I/O2R I/O3R I/O4R I/O5R I/O6R I/O0R I/O7R GND VCC GND VCC NC GND NC I/O2L I/O1L I/O7L I/O6L I/O5L I/O4L Notes: 5. This pin is NC for CY7C09089. 6. For CY7C09089, pin #23 connected to VCC is equivalent to an IDT x8 pipelined device; connecting pin #23 and #53 to GND is equivalent to an IDT x8 flowthrough device. Document #: 38-06039 Rev. *A I/O3L I/O0L NC Page 3 of 19 CY7C09089/99 CY7C09189/99 Pin Configurations (continued) 100-Pin TQFP (Top View) CNTENR CNTENL ADSR CLKR ADSL CLKL GND GND A0R A1R A2R A3R A4R A5R A6R A6L A5L A4L A3L A2L A1L A0L NC NC 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 NC NC A7L A8L A9L A10L A11L A12L A13L A14L A15L [7] A16L VCC NC NC NC NC CE0L CE1L CNTRSTL R/WL OEL FT/PIPEL NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 75 74 73 72 71 70 69 68 67 66 NC NC A7R A8R A9R A10R A11R A12R A13R A14R A15R A16R GND NC NC NC NC CE0R CE1R CNTRSTR R/WR OER FT/PIPER GND NC [7] CY7C09199 (128K x 9) CY7C09189 (64K x 9) NC 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 NC I/O2R I/O3R I/O4R I/O5R I/O6R I/O7R I/O0R I/O8R I/01R GND VCC GND VCC GND I/O2L I/O1L I/O8L I/O7L I/O6L I/O5L I/O4L Selection Guide CY7C09089/99 CY7C09189/99 -6[1] fMAX2 (MHz) (Pipelined) Max Access Time (ns) (Clock to Data, Pipelined) Typical Operating Current ICC (mA) Typical Standby Current for ISB1 (mA) (Both ports TTL Level) Typical Standby Current for ISB3 (mA) (Both ports CMOS Level) Note: 7. This pin is NC for CY7C09189. I/O3L I/O0L CY7C09089/99 CY7C09189/99 -7 83 7.5 235 40 0.05 CY7C09089/99 CY7C09189/99 -9 67 9 215 35 0.05 NC CY7C09089/99 CY7C09189/99 -12 50 12 195 30 0.05 100 6.5 250 45 0.05 Document #: 38-06039 Rev. *A Page 4 of 19 CY7C09089/99 CY7C09189/99 Pin Definitions Left Port A0L–A16L ADSL Right Port A0R–A16R ADSR Description Address Inputs (A0−A15 for 64K; and A0−A16 for 128K devices). Address Strobe Input. Used as an address qualifier. This signal should be asserted LOW to access the part using an externally supplied address. Asserting this signal LOW also loads the burst counter with the address present on the address pins. Chip Enable Input. To select either the left or right port, both CE0 AND CE1 must be asserted to their active states (CE0 ≤ VIL and CE1 ≥ VIH). Clock Signal. This input can be free running or strobed. Maximum clock input rate is fMAX. Counter Enable Input. Asserting this signal LOW increments the burst address counter of its respective port on each rising edge of CLK. CNTEN is disabled if ADS or CNTRST are asserted LOW. Counter Reset Input. Asserting this signal LOW resets the burst address counter of its respective port to zero. CNTRST is not disabled by asserting ADS or CNTEN. Data Bus Input/Output (I/O0–I/O7 for x8 devices; I/O0–I/O8 for x9 devices). Output Enable Input. This signal must be asserted LOW to enable the I/O data pins during read operations. Read/Write Enable Input. This signal is asserted LOW to write to the dual port memory array. For read operations, assert this pin HIGH. Flow-Through/Pipelined Select Input. For flow-through mode operation, assert this pin LOW. For pipelined mode operation, assert this pin HIGH. Ground Input. No Connect. Power Input. Output Current into Outputs (LOW)............................. 20 mA Static Discharge Voltage ........................................... >2001V Latch-Up Current...................................................... >200mA CE0L,CE1L CLKL CNTENL CE0R,CE1R CLKR CNTENR CNTRSTL I/O0L–I/O8L OEL R/WL FT/PIPEL GND NC VCC CNTRSTR I/O0R–I/O8R OER R/WR FT/PIPER Maximum Ratings [8] (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ................................. –65°C to +150°C Ambient Temperature with Power Applied .. –55°C to +125°C Supply Voltage to Ground Potential ............... –0.3V to +7.0V DC Voltage Applied to Outputs in High Z State ................................. –0.5V to +7.0V DC Input Voltage............................................ –0.5V to +7.0V Operating Range Range Commercial Industrial[9] Ambient Temperature 0°C to +70°C −40°C to +85°C VCC 5V ± 10% 5V ± 10% Note: 8. The Voltage on any input or I/O pin cannot exceed the power pin during power-up. 9. Industrial parts are available in CY7C09099 and CY7C09199 only. Document #: 38-06039 Rev. *A Page 5 of 19 CY7C09089/99 CY7C09189/99 Electrical Characteristics Over the Operating Range CY7C09089/99 CY7C09189/99 -6[1] Parameter VOH VOL VIH VIL IOZ ICC Description Output HIGH Voltage (VCC = Min., IOH = –4.0 mA) Output LOW Voltage (VCC = Min., IOH = +4.0 mA) Input HIGH Voltage Input LOW Voltage Output Leakage Current Operating Current (VCC = Max., IOUT = 0 mA) Outputs Disabled Com’l. Ind.[9] 45 115 40 105 −10 250 2.2 0.8 10 450 −10 235 2.4 0.4 2.2 0.8 10 420 −10 210 245 35 50 175 235 160 220 140 160 0.05 0.5 0.05 0.5 .05 0.05 160 200 145 185 130 145 2.4 0.4 2.2 0.8 10 350 410 95 110 205 220 0.5 0.5 170 185 110 150 0.05 0.5 125 190 30 85 −10 195 -7 2.4 0.4 2.2 0.8 10 305 -9 2.4 0.4 -12 V V V V µA mA mA mA mA mA mA mA mA mA mA Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit ISB1 Standby Current (Both Com’l. Ports TTL Level)[10] Ind.[9] CEL & CER ≥ VIH, f = fMAX Standby Current (One Port TTL Level)[10] CEL | CER ≥ VIH, f = fMAX Com’l. Ind. [9] ISB2 ISB3 Standby Current (Both Com’l. Ports CMOS Level)[10] Ind.[9] CEL & CER ≥ VCC – 0.2V, f = 0 Standby Current (One Port CMOS Level)[10] CEL | CER ≥ VIH, f = fMAX Com’l. Ind.[9] ISB4 Capacitance Parameter CIN COUT Description Input Capacitance Output Capacitance Test Conditions TA = 25°C, f = 1 MHz, VCC = 5.0V Max. 10 10 Unit pF pF Note: 10. CEL and CER are internal signals. To select either the left or right port, both CE0 AND CE1 must be asserted to their active states (CE0 ≤ VIL and CE1 ≥ VIH). Document #: 38-06039 Rev. *A Page 6 of 19 CY7C09089/99 CY7C09189/99 AC Test Loads 5V 5V R1 = 893Ω OUTPUT C = 30 pF R2 = 347Ω OUTPUT C = 30 pF VTH = 1.4V RTH = 250Ω R1 = 893Ω OUTPUT C = 5 pF R2 = 347Ω (a) Normal Load (Load 1) (b) Thévenin Equivalent (Load 1) (c) Three-State Delay (Load 2) (Used for tCKLZ, tOLZ, & tOHZ including scope and jig) AC Test Loads (Applicable to -6 only)[11] OUTPUT Z0 = 50Ω C R = 50Ω 3.0V GND VTH = 1.4V 10% ALL INPUT PULSES 90% 90% 10% ≤ 3 ns ≤ 3 ns (a) Load 1 (-6 only) 0. 60 0. 50 ∆ (ns) for all -6 access times 0. 40 0. 30 0. 20 0. 1 0 0. 00 10 15 20 25 30 35 Capacitance (pF) (b) Load Derating Curve Note: 11. Test Conditions: C = 10 pF. Document #: 38-06039 Rev. *A Page 7 of 19 CY7C09089/99 CY7C09189/99 Switching Characteristics Over the Operating Range CY7C09089/99 CY7C09189/99 -6[1] Parameter fMAX1 fMAX2 tCYC1 tCYC2 tCH1 tCL1 tCH2 tCL2 tR tF tSA tHA tSC tHC tSW tHW tSD tHD tSAD tHAD tSCN tHCN tSRST tHRST tOE tOLZ [12, 13] [12, 13] -7 Min. Max. 45 83 22 12 7.5 7.5 5 5 3 3 3 3 4 0 4 0 4 0 4 0 4 0 4 0 4 0 8 9 2 7 15 6.5 1 7 18 7.5 2 9 2 2 9 2 2 2 2 1 4 1 4 1 4 1 4 1 4 1 4 1 4 1 25 15 12 12 6 6 Min. 53 -9 Max. 40 67 30 20 12 12 8 8 3 3 4 1 4 1 4 1 4 1 4 1 4 1 4 1 10 2 7 20 9 2 9 2 2 1 -12 Min. Max. 33 50 Unit MHz MHz ns ns ns ns ns ns 3 3 ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns 12 7 25 12 9 ns ns ns ns ns ns ns ns Description fMax Flow-Through fMax Pipelined Clock Cycle Time - Flow-Through Clock Cycle Time - Pipelined Clock HIGH Time - Flow-Through Clock LOW Time - Flow-Through Clock HIGH Time - Pipelined Clock LOW Time - Pipelined Clock Rise Time Clock Fall Time Address Set-Up Time Address Hold Time Chip Enable Set-Up Time Chip Enable Hold Time R/W Set-Up Time R/W Hold Time Input Data Set-Up Time Input Data Hold Time ADS Set-Up Time ADS Hold Time CNTEN Set-Up Time CNTEN Hold Time CNTRST Set-Up Time CNTRST Hold Time Output Enable to Data Valid OE to Low Z OE to High Z Clock to Data Valid - Flow-Through Clock to Data Valid - Pipelined Data Output Hold After Clock HIGH Min. Max. 100 19 10 6.5 6.5 4 4 3.5 0 3.5 0 3.5 0 3.5 0 3.5 0 3.5 0 3.5 0 2 1 tOHZ tCD1 tCD2 tDC 2 2 2 tCKHZ tCKLZ [12, 13] Clock HIGH to Output High Z Clock HIGH to Output Low Z [12, 13] Port to Port Delays tCWDD tCCS Write Port Clock HIGH to Read Data Delay Clock to Clock Set-Up Time 30 9 35 10 40 15 40 15 ns ns Notes: 12. Test conditions used are Load 2. 13. This parameter is guaranteed by design, but is not production tested. Document #: 38-06039 Rev. *A Page 8 of 19 CY7C09089/99 CY7C09189/99 Switching Waveforms Read Cycle for Flow-Through Output (FT/PIPE = VIL)[14, 15, 16, 17] tCH1 CLK tCYC1 tCL1 CE0 tSC CE1 tHC tSC tHC R/W tSW tSA ADDRESS DATAOUT tCKLZ tOHZ OE tOE tOLZ An tCD1 tHW tHA An+1 tDC Qn Qn+1 An+2 An+3 tCKHZ Qn+2 tDC Read Cycle for Pipelined Operation (FT/PIPE = VIH)[14, 15, 16, 17] tCH2 CLK tCYC2 tCL2 CE0 tSC CE1 tHC tSC tHC R/W tSW tSA ADDRESS DATAOUT An 1 Latency tHW tHA An+1 tCD2 Qn tCKLZ OE tOE Notes: 14. OE is asynchronously controlled; all other inputs are synchronous to the rising clock edge. 15. ADS = VIL, CNTEN and CNTRST = VIH. 16. The output is disabled (high-impedance state) by CE0=VIH or CE1 = VIL following the next rising edge of the clock. 17. Addresses do not have to be accessed sequentially since ADS = VIL constantly loads the address on the rising edge of the CLK. Numbers are for reference only. An+2 tDC Qn+1 tOHZ An+3 Qn+2 tOLZ Document #: 38-06039 Rev. *A Page 9 of 19 CY7C09089/99 CY7C09189/99 Switching Waveforms (continued) Bank Select Pipelined Read[18, 19] tCYC2 tCH2 CLKL tSA ADDRESS(B1) tSC CE0(B1) A0 tCL2 tHA A1 tHC A2 A3 A4 A5 tCD2 DATAOUT(B1) tSA ADDRESS(B2) A0 tHA A1 tSC CE0(B2) tSC DATAOUT(B2) tHC tSC D0 tHC tCD2 D1 tCKHZ tCD2 D3 tCKHZ tDC A2 tHC tDC A3 A4 tCKLZ A5 tCD2 D2 tCKLZ tCKHZ tCD2 D4 tCKLZ Left Port Write to Flow-Through Right Port Read[20, 21, 22, 23] CLKL tSW R/WL tSA ADDRESSL tSD DATAINL CLKR R/WR ADDRESSR tSW tSA tHW tHA NO MATCH tCWDD DATAOUTR tDC VALID tDC tCD1 VALID VALID tCCS tCD1 MATCH tHD tHA NO MATCH tHW MATCH Notes: 18. In this depth expansion example, B1 represents Bank #1 and B2 is Bank #2; Each Bank consists of one Cypress dual-port device from this data sheet. ADDRESS(B1) = ADDRESS(B2). 19. OE and ADS = VIL; CE1(B1), CE1(B2), R/W, CNTEN, and CNTRST = VIH. 20. The same waveforms apply for a right port write to flow-through left port read. 21. CE0 and ADS = VIL; CE1, CNTEN, and CNTRST = VIH. 22. OE = VIL for the right port, which is being read from. OE = VIH for the left port, which is being written to. 23. It tCCS ≤ maximum specified, then data from right port READ is not valid until the maximum specified for tCWDD. If tCCS>maximum specified, then data is not valid until tCCS + tCD1. tCWDD does not apply in this case. Document #: 38-06039 Rev. *A Page 10 of 19 CY7C09089/99 CY7C09189/99 Switching Waveforms (continued) Pipelined Read-to-Write-to-Read (OE = VIL)[17, 24, 25, 26] tCH2 CLK tCYC2 tCL2 CE0 tSC CE1 tSW R/W tSW ADDRESS tSA DATAIN An tHA tCD2 Qn READ NO OPERATION WRITE READ tCKHZ tHW An+1 An+2 An+2 tSD tHD Dn+2 tCKLZ tCD2 Qn+3 An+3 An+4 tHW tHC DATAOUT Pipelined Read-to-Write-to-Read (OE Controlled)[17, 24, 25, 26] tCH2 CLK tCYC2 tCL2 CE0 tSC tHC CE1 tSW tHW R/W tSW An tHW An+1 tHA An+2 tSD tHD Dn+2 tCD2 Dn+3 tCKLZ Qn tOHZ tCD2 Qn+4 An+3 An+4 An+5 ADDRESS tSA DATAIN DATAOUT OE READ WRITE READ Notes: 24. Output state (HIGH, LOW, or High-Impedance) is determined by the previous cycle control signals. 25. CE0 and ADS = VIL; CE1, CNTEN, and CNTRST = VIH. 26. During “No Operation,” data in memory at the selected address may be corrupted and should be rewritten to ensure data integrity. Document #: 38-06039 Rev. *A Page 11 of 19 CY7C09089/99 CY7C09189/99 Switching Waveforms (continued) Flow-Through Read-to-Write-to-Read (OE = VIL)[15, 18, 24, 25] tCH1 CLK tCYC1 tCL1 CE0 tSC CE1 tSW R/W tSW ADDRESS tSA DATAIN tCD1 Qn tDC READ An tHA tCD1 Qn+1 tCKHZ NO OPERATION tCKLZ WRITE tHW An+1 An+2 tSD Dn+2 tCD1 Qn+3 tDC READ tCD1 An+2 tHD An+3 An+4 tHW tHC DATAOUT Flow-Through Read-to-Write-to-Read (OE Controlled)[15, 18, 24, 25] tCYC1 tCL1 tCH1 CLK CE0 tSC CE1 tSW R/W tSW An ADDRESS tSA DATAIN tCD1 Qn tOHZ tCKLZ tHA tDC tSD Dn+2 tHD Dn+3 tOE tCD1 Qn+4 tDC tCD1 tHW An+1 An+2 An+3 An+4 An+5 tHW tHC DATAOUT OE READ WRITE READ Document #: 38-06039 Rev. *A Page 12 of 19 CY7C09089/99 CY7C09189/99 Switching Waveforms (continued) Pipelined Read with Address Counter Advance[27] tCYC2 tCL2 tCH2 CLK tSA ADDRESS tSAD ADS An tHA tHAD tSAD CNTEN tSCN DATAOUT Qx-1 READ EXTERNAL ADDRESS tHCN Qx tDC READ WITH COUNTER tCD2 Qn tSCN Qn+1 tHAD tHCN Qn+2 Qn+3 COUNTER HOLD READ WITH COUNTER Flow-Through Read with Address Counter Advance[27] tCYC1 tCL1 tCH1 CLK tSA ADDRESS tSAD ADS An tHA tHAD tSAD tHAD CNTEN tSCN tHCN tCD1 Qx tDC Qn Qn+1 tSCN tHCN DATAOUT Qn+2 READ WITH COUNTER Qn+3 READ EXTERNAL ADDRESS READ WITH COUNTER COUNTER HOLD Note: 27. CE0 and OE = VIL; CE1, R/W and CNTRST = VIH. Document #: 38-06039 Rev. *A Page 13 of 19 CY7C09089/99 CY7C09189/99 Switching Waveforms (continued) Write with Address Counter Advance (Flow-Through or Pipelined Outputs)[28, 29] tCH2 CLK tSA ADDRESS An tHA tCYC2 tCL2 INTERNAL ADDRESS tSAD ADS tHAD An An+1 An+2 An+3 An+4 CNTEN tSCN DATAIN tSD Dn tHD WRITE EXTERNAL ADDRESS tHCN Dn+1 WRITE WITH COUNTER Dn+1 Dn+2 Dn+3 Dn+4 WRITE COUNTER HOLD WRITE WITH COUNTER Notes: 28. CE0 and R/W = VIL; CE1 and CNTRST = VIH. 29. The “Internal Address” is equal to the “External Address” when ADS = VIL and equals the counter output when ADS = VIH. Document #: 38-06039 Rev. *A Page 14 of 19 CY7C09089/99 CY7C09189/99 Switching Waveforms (continued) Counter Reset (Pipelined Outputs)[17, 24, 30, 31] tCYC2 tCL2 tCH2 CLK tSA ADDRESS INTERNAL ADDRESS AX tSW tHW 0 1 An tHA An+1 An An+1 R/W tSAD ADS tSCN CNTEN tSRST CNTRST DATAIN tHRST tSD D0 tHD tHCN tHAD DATAOUT COUNTER RESET WRITE ADDRESS 0 READ ADDRESS 0 Q0 READ ADDRESS 1 Q1 READ ADDRESS n Qn Notes: 30. CE0 = VIL; CE1 = VIH. 31. No dead cycle exists during counter reset. A READ or WRITE cycle may be coincidental with the counter reset. Document #: 38-06039 Rev. *A Page 15 of 19 CY7C09089/99 CY7C09189/99 Read/Write and Enable Operation[32, 33, 34] Inputs OE X X X L H X CLK CE0 H X L L L CE1 X L H H H R/W X X L H X Outputs I/O0–I/O8 High-Z High-Z DIN DOUT High-Z Operation Deselected[35] Deselected[35] Write Read[33] Outputs Disabled Address Counter Control Operation[32, 36, 37, 38] Address X An X X Previous Address X X An An CLK ADS X L H H CNTEN X X H L CNTRST L H H H I/O Dout(0) Dout(n) Dout(n) Dout(n+1) Mode Reset Load Hold Increment Operation Counter Reset to Address 0 Address Load into Counter External Address Blocked—Counter Disabled Counter Enabled—Internal Address Generation Notes: 32. “X” = “Don’t Care,” “H” = VIH, “L” = VIL. 33. ADS, CNTEN, CNTRST = “Don’t Care.” 34. OE is an asynchronous input signal. 35. When CE changes state in the pipelined mode, deselection and read happen in the following clock cycle. 36. CE0 and OE = VIL; CE1 and R/W = VIH. 37. Data shown for flow-through mode; pipelined mode output will be delayed by one cycle. 38. Counter operation is independent of CE0 and CE1. Document #: 38-06039 Rev. *A Page 16 of 19 CY7C09089/99 CY7C09189/99 Ordering Information 64K x8 Synchronous Dual-Port SRAM Speed (ns) 6.5[1] 7.5 9 12 Ordering Code CY7C09089-6AC CY7C09089-7AC CY7C09089-9AC CY7C09089-12AC Package Name A100 A100 A100 A100 Package Type 100-Pin Thin Quad Flat Pack 100-Pin Thin Quad Flat Pack 100-Pin Thin Quad Flat Pack 100-Pin Thin Quad Flat Pack Operating Range Commercial Commercial Commercial Commercial 128K x8 Synchronous Dual-Port SRAM Speed (ns) 6.5 7.5 9 12 Ordering Code CY7C09099-6AC CY7C09099-7AC CY7C09099-9AC CY7C09099-9AI CY7C09099-12AC Package Name A100 A100 A100 A100 A100 Package Type 100-Pin Thin Quad Flat Pack 100-Pin Thin Quad Flat Pack 100-Pin Thin Quad Flat Pack 100-Pin Thin Quad Flat Pack 100-Pin Thin Quad Flat Pack Operating Range Commercial Commercial Commercial Industrial Commercial 64K x9 Synchronous Dual-Port SRAM Speed (ns) 6.5 7.5 9 12 Ordering Code CY7C09189-6AC CY7C09189-7AC CY7C09189-9AC CY7C09189-12AC Package Name A100 A100 A100 A100 Package Type 100-Pin Thin Quad Flat Pack 100-Pin Thin Quad Flat Pack 100-Pin Thin Quad Flat Pack 100-Pin Thin Quad Flat Pack Operating Range Commercial Commercial Commercial Commercial 128K x9 Synchronous Dual-Port SRAM Speed (ns) 6.5 7.5 9 12 Ordering Code CY7C09199-6AC CY7C09199-7AC CY7C09199-9AC CY7C09199-9AI CY7C09199-12AC Package Name A100 A100 A100 A100 A100 Package Type 100-Pin Thin Quad Flat Pack 100-Pin Thin Quad Flat Pack 100-Pin Thin Quad Flat Pack 100-Pin Thin Quad Flat Pack 100-Pin Thin Quad Flat Pack Operating Range Commercial Commercial Commercial Industrial Commercial Document #: 38-06039 Rev. *A Page 17 of 19 CY7C09089/99 CY7C09189/99 Package Diagram 100-Pin Thin Plastic Quad Flat Pack (TQFP) A100 51-85048-B Document #: 38-06039 Rev. *A Page 18 of 19 © Cypress Semiconductor Corporation, 2001. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges. CY7C09089/99 CY7C09189/99 Document Title: CY7C09089/99, CY7C09189/99 64K/128K x 8/9 Synchronous Dual Port Static RAM Document Number: 38-06039 REV. ** *A ECN NO. 110187 122289 Issue Date 10/21/01 12/27/02 Orig. of Change SZV RBI Description of Change Change from Spec number: 38-00663 to 38-06039 Added power up information to maximum ratings information. Document #: 38-06039 Rev. *A Page 19 of 19