CY7C1031-10JC

CY7C1031 CY7C1032 64K x 18 Synchronous Cache RAM Features Functional Description The CY7C1031 and CY7C1032 are 64K by 18 synchronous cache RAMs designed to interface with high-speed microprocessors with minimum glue logic. Maximum access delay from clock rise is 8.5 ns. A 2-bit on-chip counter captures the first address in a burst and increments the address automatically for the rest of the burst access. • Supports 66-MHz Pentium® microprocessor cache systems with zero wait states • 64K by 18 common I/O • Fast clock-to-output times — 8.5 ns The CY7C1031 is designed for Intel® Pentium and i486 CPU-based systems; its counter follows the burst sequence of the Pentium and the i486 processors. The CY7C1032 is architected for processors with linear burst sequences. Burst accesses can be initiated with the processor address strobe (ADSP) or the cache controller address strobe (ADSC) inputs. Address advancement is controlled by the address advancement (ADV) input. • Two-bit wraparound counter supporting Pentium microprocessor and 486 burst sequence (CY7C1031) • Two-bit wraparound counter supporting linear burst sequence (CY7C1032) • Separate processor and controller address strobes • Synchronous self-timed write • Direct interface with the processor and external cache controller • Asynchronous output enable • I/Os capable of 3.3V operation A synchronous self-timed write mechanism is provided to simplify the write interface. A synchronous chip select input and an asynchronous output enable input provide easy control for bank selection and output three-state control. • JEDEC-standard pinout • 52-pin PLCC packaging Logic Block Diagram Pin Configuration A15 –A0 ADDR REG 64K X 9 64K X 9 RAM ARRAY RAM ARRAY WH TIMING CONTROL WL 9 9 8 9 10 11 12 13 14 15 16 17 18 19 20 OE A8 A9 A10 WH WL ADSC ADSP CS DQ8 DQ9 VCCQ VSSQ DQ10 DQ11 DQ12 DQ13 VSSQ VCCQ DQ14 DQ15 [1] DP1 16 ADV LOGIC CLK ADSP ADSC CS WH WL 9 14 2 2 ADV 9 A6 A7 DATA IN REGISTER 14 7 6 5 4 3 2 1 52 51 50 49 48 47 46 45 44 43 42 41 7C1031 7C1032 40 39 38 37 36 35 34 2122 23 24 25 26 27 28 29 30 31 32 33 [1] DP0 DQ7 DQ6 VCCQ VSSQ DQ5 DQ4 DQ3 DQ2 VSSQ VCCQ DQ1 DQ0 A5 A 4 A 3 A 2 A1 A0 GND V CC A 15 A14 A13 A12 A11 16 ADV CLK PLCC Top View 18 18 DQ15 – DQ0 DP1 – DP0 OE Selection Guide 7C1031-8 7C1032-8 7C1031-10 7C1032-10 7C1031-12 8.5 10 12 ns 280 280 230 mA Maximum Access Time Maximum Operating Current Commercial Unit Note: 1. DP0 and DP1 are functionally equivalent to DQx. Cypress Semiconductor Corporation Document #: 38-05278 Rev. *A • 3901 North First Street • San Jose, CA 95134 • 408-943-2600 Revised April 1, 2004 CY7C1031 CY7C1032 Single Write Accesses Initiated by ADSP Single Read Accesses This access is initiated when the following conditions are satisfied at clock rise: (1) CS is LOW and (2) ADSP is LOW. ADSP-triggered write cycles are completed in two clock periods. The address at A0 through A15 is loaded into the address register and address advancement logic and delivered to the RAM core. The write signal is ignored in this cycle because the cache tag or other external logic uses this clock period to perform address comparisons or protection checks. If the write is allowed to proceed, the write input to the CY7C1031 and CY7C1032 will be pulled LOW before the next clock rise. ADSP is ignored if CS is HIGH. A single read access is initiated when the following conditions are satisfied at clock rise: (1) CS is LOW, (2) ADSP or ADSC is LOW, and (3) WH and WL are HIGH. The address at A0 through A15 is stored into the address advancement logic and delivered to the RAM core. If the output enable (OE) signal is asserted (LOW), data will be available at the data outputs a maximum of 8.5 ns after clock rise. ADSP is ignored if CS is HIGH. If WH, WL, or both are LOW at the next clock rise, information presented at DQ0–DQ15 and DP0–DP1 will be written into the location specified by the address advancement logic. WL controls the writing of DQ0–DQ7 and DP0 while WH controls the writing of DQ8–DQ15 and DP1. Because the CY7C1031 and CY7C1032 are common-I/O devices, the output enable signal (OE) must be deasserted before data from the CPU is delivered to DQ0–DQ15 and DP0–DP1. As a safety precaution, the appropriate data lines are three-stated in the cycle where WH, WL, or both are sampled LOW, regardless of the state of the OE input. Burst Sequences The CY7C1031 provides a 2-bit wraparound counter, fed by pins A0–A1, that implements the Intel 80486 and Pentium processor’s address burst sequence (see Table 1). Note that the burst sequence depends on the first burst address. Table 1. Counter Implementation for the Intel Pentium/ 80486 Processor’s Sequence First Address Second Address Third Address Fourth Address AX + 1, Ax AX + 1, Ax AX + 1, Ax AX + 1, Ax 00 01 10 11 Single Write Accesses Initiated by ADSC 01 00 11 10 This write access is initiated when the following conditions are satisfied at rising edge of the clock: (1) CS is LOW, (2) ADSC is LOW, and (3) WH or WL are LOW. ADSC-triggered accesses are completed in a single clock cycle. 10 11 00 01 11 10 01 00 The address at A0 through A15 is loaded into the address register and address advancement logic and delivered to the RAM core. Information presented at DQ0–DQ15 and DP0–DP1 will be written into the location specified by the address advancement logic. Since the CY7C1031 and the CY7C1032 are common-I/O devices, the output enable signal (OE) must be deasserted before data from the cache controller is delivered to the data and parity lines. As a safety precaution, the appropriate data and parity lines are three-stated in the cycle where WH and WL are sampled LOW regardless of the state of the OE input. Document #: 38-05278 Rev. *A The CY7C1032 provides a 2-bit wraparound counter, fed by pins A0–A1, that implements a linear address burst sequence (see Table 2). Table 2. Counter Implementation for a Linear Sequence First Address Second Address Third Address Fourth Address AX + 1, Ax AX + 1, Ax AX + 1, Ax AX + 1, Ax 00 01 10 11 01 10 11 00 10 11 00 01 11 00 01 10 Page 2 of 13 CY7C1031 CY7C1032 Application Example Figure 1 shows a 512-Kbyte secondary cache for the Pentium microprocessor using four CY7C1031 cache RAMs. 512 KB 66-MHz OSC CLK CLK ADR ADR DATA DATA ADS ADSP ADSC PENTIUM PROCESSOR 7C1031 ADV OE 2 CLK ADR CD CACHE TAG DATA MATCH DIRTY VALID WH, WL WH, WL WH, WL WH, WL 2 2 2 WH1, CLK ADSC ADV OE WH0, WL1 WL0 ADR DATA ADSP CACHE CONTROLLER WH2, WL2 WH3, WL3 INTERFACE TO MAIN MEMORY MATCH DIRTY VALID Figure 1. Cache Using Four CY7C1031s Pin Definitions Signal Name VCC Type Input # of Pins 1 Description +5V Power VCCQ Input 4 +5V or 3.3V (Outputs) GND Input 1 Ground VSSQ Input 4 Ground (Outputs) CLK Input 1 Clock A15 – A0 Input 16 Address ADSP Input 1 Address Strobe from Processor ADSC Input 1 Address Strobe from Cache Controller WH Input 1 Write Enable – High Byte WL Input 1 Write Enable – Low Byte ADV Input 1 Advance OE Input 1 Output Enable CS Input 1 Chip Select DQ15–DQ0 Input/Output 16 Regular Data DP1–DP0 Input/Output 2 Parity Data Document #: 38-05278 Rev. *A Page 3 of 13 CY7C1031 CY7C1032 Pin Descriptions Signal Name I/O Description Input Signals CLK I Clock signal. It is used to capture the address, the data to be written, and the following control signals: ADSP, ADSC, CS, WH, WL, and ADV. It is also used to advance the on-chip auto-address-increment logic (when the appropriate control signals have been set). A15–A0 I Sixteen address lines used to select one of 64K locations. They are captured in an on-chip register on the rising edge of CLK if ADSP or ADSC is LOW. The rising edge of the clock also loads the lower two address lines, A1–A0, into the on-chip auto-address-increment logic if ADSP or ADSC is LOW. ADSP I Address strobe from processor. This signal is sampled at the rising edge of CLK. When this input and/or ADSC is asserted, A0–A15 will be captured in the on-chip address register. It also allows the lower two address bits to be loaded into the on-chip auto-address-increment logic. If both ADSP and ADSC are asserted at the rising edge of CLK, only ADSP will be recognized. The ADSP input should be connected to the ADS output of the processor. ADSP is ignored when CS is HIGH. ADSC I Address strobe from cache controller. This signal is sampled at the rising edge of CLK. When this input and/or ADSP is asserted, A0–A15 will be captured in the on-chip address register. It also allows the lower two address bits to be loaded into the on-chip auto-address-increment logic. The ADSC input should not be connected to the ADS output of the processor. WH I Write signal for the high-order half of the RAM array. This signal is sampled by the rising edge of CLK. If WH is sampled as LOW, i.e., asserted, the control logic will perform a self-timed write of DQ15–DQ8 and DP1 from the on-chip data register into the selected RAM location. There is one exception to this. If ADSP, WH, and CS are asserted (LOW) at the rising edge of CLK, the write signal, WH, is ignored. Note that ADSP has no effect on WH if CS is HIGH. WL I Write signal for the low-order half of the RAM array. This signal is sampled by the rising edge of CLK. If WL is sampled as LOW, i.e., asserted, the control logic will perform a self-timed write of DQ7–DQ0 and DP0 from the on-chip data register into the selected RAM location. There is one exception to this. If ADSP, WL, and CS are asserted (LOW) at the rising edge of CLK, the write signal, WL, is ignored. Note that ADSP has no effect on WL if CS is HIGH. ADV I Advance. This signal is sampled by the rising edge of CLK. When it is asserted, it automatically increments the 2-bit on-chip auto-address-increment counter. In the CY7C1032, the address will be incremented linearly. In the CY7C1031, the address will be incremented according to the Pentium/486 burst sequence. This signal is ignored if ADSP or ADSC is asserted concurrently with CS. Note that ADSP has no effect on ADV if CS is HIGH. CS I Chip select. This signal is sampled by the rising edge of CLK. If CS is HIGH and ADSC is LOW, the SRAM is deselected. If CS is LOW and ADSC or ADSP is LOW, a new address is captured by the address register. If CS is HIGH, ADSP is ignored. OE I Output enable. This signal is an asynchronous input that controls the direction of the data I/O pins. If OE is asserted (LOW), the data pins are outputs, and the SRAM can be read (as long as CS was asserted when it was sampled at the beginning of the cycle). If OE is deasserted (HIGH), the data I/O pins will be three-stated, functioning as inputs, and the SRAM can be written. Bidirectional Signals DQ15–DQ0 I/O Sixteen bidirectional data I/O lines. DQ15–DQ8 are inputs to and outputs from the high-order half of the RAM array, while DQ7–DQ0 are inputs to and outputs from the low-order half of the RAM array. As inputs, they feed into an on-chip data register that is triggered by the rising edge of CLK. As outputs, they carry the data read from the selected location in the RAM array. The direction of the data pins is controlled by OE: when OE is HIGH, the data pins are three-stated and can be used as inputs; when OE is LOW, the data pins are driven by the output buffers and are outputs. DQ15–DQ8 and DQ7–DQ0 are also three-stated when WH and WL, respectively, is sampled LOW at clock rise. DP1–DP0 I/O Two bidirectional data I/O lines. These operate in exactly the same manner as DQ15–DQ0, but are named differently because their primary purpose is to store parity bits, while the DQs’ primary purpose is to store ordinary data bits. DP1 is an input to and an output from the high-order half of the RAM array, while DP0 is an input to and an output from the lower-order half of the RAM array. Document #: 38-05278 Rev. *A Page 4 of 13 CY7C1031 CY7C1032 DC Input Voltage[2] ...........................................–0.5V to VCC + 0.5V Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ...................................–65°C to +150°C Ambient Temperature with Power Applied...............................................–55°C to +125°C Current into Outputs (LOW)......................................... 20 mA Static Discharge Voltage.......................................... > 2001V (per MIL-STD-883, Method 3015) Latch-up Current.................................................... > 200 mA Operating Range Supply Voltage on VCC Relative to GND ............ –0.5V to +7.0V DC Voltage Applied to Outputs in High-Z State[2] ...............................................–0.5V to VCC + 0.5V Range Ambient Temperature[3] VCC VCCQ 0°C to +70°C 5V ± 5% 3.0V to VCC Com’l Electrical Characteristics Over the Operating Range[4] 7C1031-8 7C1032-8 Parameter Description 7C1031-10 7C1032-10 7C1031-12 Test Conditions Min. Max. Min. Max. Min. Max. Unit VOH Output HIGH Voltage VCC = Min., IOH = –4.0 mA 2.4 VCCQ 2.4 VCCQ 2.4 VCCQ V VOL Output LOW Voltage VCC = Min., IOL = 8.0 mA VIH Input HIGH Voltage VIL Input LOW Voltage[2] –0.3 0.8 –0.3 0.8 –0.3 0.8 V IX Input Load Current GND ≤ VI ≤ VCC –1 1 –1 1 –1 1 µA IOZ Output Leakage Current GND ≤ VI ≤ VCC, Output Disabled –5 5 –5 5 –5 5 µA IOS Output Short Circuit Current[5] VCC = Max., VOUT = GND –300 –300 –300 mA ICC VCC Operating Supply Current VCC = Max., Com’l IOUT = 0 mA, f = fMAX = 1/tCYC 280 280 230 mA ISB1 Automatic CE Power-down Current—TTL Inputs Max. VCC, CS ≥ Com’l VIH, VIN ≥ VIH or VIN ≤ VIL, f = fMAX 80 80 60 mA ISB2 Automatic CE Power-down Current — CMOS Inputs Max. VCC, CS ≥ Com’l VCC – 0.3V, VIN ≥ VCC – 0.3V or VIN ≤ 0.3V, f = 0[6] 30 30 30 mA 0.4 2.2 0.4 VCC + 0.3V 2.2 VCC + 0.3V 2.2 0.4 V VCC + 0.3V V Capacitance[7] Parameter CIN: Addresses Description Input Capacitance CIN: Other Inputs COUT Output Capacitance Test Conditions TA = 25°C, f = 1 MHz, VCC = 5.0V Com’l Max. Unit 4.5 pF Com’l 5 pF Com’l 8 pF Notes: 2. Minimum voltage equals –2.0V for pulse durations of less than 20 ns. 3. TA is the case temperature. 4. See the last page for Group A subgroup testing information. 5. Not more than one output should be shorted at one time. Duration of the short circuit should not exceed 30 seconds. 6. Inputs are disabled, clock is allowed to run at speed. 7. Tested initially and after any design or process changes that may affect these parameters. Document #: 38-05278 Rev. *A Page 5 of 13 CY7C1031 CY7C1032 AC Test Loads and Waveforms R1 VCCQ OUTPUT ALL INPUT PULSES OUTPUT Z0 = 50Ω 3.0V RL = 50Ω R2 5 pF VL =1.5V INCLUDING JIGAND SCOPE (a) GND 90% 10% 90% 10% ≤ 3 ns ≤ 3 ns (b) [8] Switching Characteristics Over the Operating Range[9] 7C1031-8 7C1032-8 Parameter Description tCYC Clock Cycle Time Min. Max. 7C1031-10 7C1032-10 Min. Max. 7C1031-12 Min. Max. Unit 15[10] 20 20 ns tCH Clock HIGH 5 8 8 ns tCL Clock LOW 5 8 8 ns tAS Address Set-Up Before CLK Rise 2.5 2.5 2.5 ns tAH Address Hold After CLK Rise 0.5 0.5 0.5 ns tCDV Data Output Valid After CLK Rise tDOH Data Output Hold After CLK Rise tADS ADSP, ADSC Set-Up Before CLK Rise tADSH ADSP, ADSC Hold After CLK Rise tWES WH, WL Set-Up Before CLK Rise 2.5 2.5 2.5 ns tWEH WH, WL Hold After CLK Rise 0.5 0.5 0.5 ns tADVS ADV Set-Up Before CLK Rise 2.5 2.5 2.5 ns tADVH ADV Hold After CLK Rise 0.5 0.5 0.5 ns 8.5 3 10 12 ns 3 3 ns 2.5 2.5 2.5 ns 0.5 0.5 0.5 ns tDS Data Input Set-Up Before CLK Rise 2.5 2.5 2.5 ns tDH Data Input Hold After CLK Rise 0.5 0.5 0.5 ns tCSS Chip Select Set-Up 2.5 2.5 2.5 ns tCSH Chip Select Hold After CLK Rise 0.5 0.5 0.5 ns Z[11] tCSOZ Chip Select Sampled to Output High tEOZ OE HIGH to Output High Z[11] tEOV OE LOW to Output Valid 5 tWEOZ WH or WL Sampled LOW to Output High Z[11, 12] 5 8.5 tWEOV WH or WL Sampled HIGH to Output Valid[12] 2 6 2 6 2 7 ns 2 6 2 6 2 7 ns 5 6 ns 6 7 ns 10 12 ns Notes: 8. Resistor values for VCCQ = 5V are: R1 = 1179Ω and R2 = 868Ω. Resistor values for VCCQ = 3.3V are R1 = 317Ω and R2 = 348Ω. 9. Unless otherwise noted, test conditions assume signal transition time of 3 ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V, and output loading of the specified IOL/IOH and load capacitance. Shown in (a) and (b) of AC Test Loads. 10. Do not use the burst mode, if device operates at a frequency above 50 MHz. 11. tCSOZ, tEOZ, and tWEOZ are specified with a load capacitance of 5 pF as in part (b) of AC Test Loads. Transition is measured ± 500 mV from steady-state voltage. 12. At any given voltage and temperature, tWEOZ min. is less than tWEOV min. Document #: 38-05278 Rev. *A Page 6 of 13 CY7C1031 CY7C1032 Switching Waveforms Single Read[13] tCH tCL tCYC CLK tCSS tCSH CS tAS tAH ADDRESS tADS [14] tADSH or ADSP ADSC tWES tWEH [15] WH, WL tCDV tDOH DATA OUT Single Write Timing: Write Initiated by ADSP tCH tCL CLK tCSS tCSH CS tAS tAH tADS tADSH ADDRESS ADSP tWES tWEH [15] WH, WL tDS tDH DATA IN DATA OUT tEOZ OE Notes: 13. OE is LOW throughout this operation. 14. If ADSP is asserted while CS is HIGH, ADSP will be ignored. 15. ADSP has no effect on ADV, WL, and WH if CS is HIGH. Document #: 38-05278 Rev. *A Page 7 of 13 CY7C1031 CY7C1032 Switching Waveforms (continued) Single Write Timing: Write Initiated by ADSC tCH tCL CLK tCSS tCSH tAS tAH tADS tADSH CS ADDRESS ADSC tWES WH, WL tWEH tDS tDH DATA IN DATA OUT tEOZ OE Burst Read Sequence with Four Accesses CLK tCSS tCSH CS tAS tAH tADS tADSH ADDRESS ADSP [14] or ADSC tADVS ADV tADVH [15] WH,WL [15] tWES tWEH OE tCDV DATA OUT OE Document #: 38-05278 Rev. *A tDOH DATA0 DATA1 DATA2 DATA3 Page 8 of 13 CY7C1031 CY7C1032 Switching Waveforms (continued) Output (Controlled by OE) DATA OUT tEOZ tEOV OE Write Burst Timing: Write Initiated by ADSC CLK tCSS tCSH tWES tWEH tADS tADSH tADS tADSH tAS tAH CS WH, WL OE ADSP [14] ADSC ADDR tADVS tADVH ADV tDS DATA tDH DATA0 Document #: 38-05278 Rev. *A DATA1 DATA2 DATA3 Page 9 of 13 CY7C1031 CY7C1032 Switching Waveforms (continued) Write Burst Timing: Write Initiated by ADSP CLK tCSS tCSH tADS tADSH tAS tAH CS WH, WL [15] OE ADSC ADSP [14] ADDR tADVS tADVH ADV [15] tDS DATA tDH DATA0 DATA1 DATA2 DATA3 Output Timing (Controlled by CS) CLK ADSC CS tADS tADSH tCSS tCSH tCDV tADS tADSH tCSS tCSH tCSOZ DATA OUT Document #: 38-05278 Rev. *A Page 10 of 13 CY7C1031 CY7C1032 Switching Waveforms (continued) Output Timing (Controlled by WH/ WL) CLK tADS tADSH tWES tWEH tADS tADSH ADSC and ADSP WH, WL tWEOZ tWEOV DATA OUT Truth Table Input CS ADSP ADSC H X ADV WH or WL L X X CLK Address Operation L→H N/A Chip deselected H L H H H L→H Same address as previous cycle Read cycle (ADSP ignored) H L H L H L→H Incremented burst address Read cycle, in burst sequence (ADSP ignored) H L H H L L→H Same address as previous cycle Write cycle (ADSP ignored) H L H L L L→H Incremented burst address Write cycle, in burst sequence (ADSP ignored) L L X X X L→H External Read cycle, begin burst L H L X H L→H External Read cycle, begin burst L H L X L L→H External Write cycle, begin burst X H H L L L→H Incremented burst address Write cycle, in burst sequence X H H L H L→H Incremented burst address Read cycle, in burst sequence X H H H L L→H Same address as previous cycle Write cycle X H H H H L→H Same address as previous cycle Read cycle Ordering Information Speed (ns) Ordering Code Package Name Package Type Operating Range 8 CY7C1031-8JC J69 52-lead Plastic Leaded Chip Carrier Commercial 10 CY7C1031-10JC J69 52-lead Plastic Leaded Chip Carrier Commercial 12 CY7C1031-12JC J69 52-lead Plastic Leaded Chip Carrier Commercial 8 CY7C1032-8JC J69 52-lead Plastic Leaded Chip Carrier Commercial 10 CY7C1032-10JC[16] J69 52-lead Plastic Leaded Chip Carrier Commercial Note: 16. EOL (End of Life). Document #: 38-05278 Rev. *A Page 11 of 13 CY7C1031 CY7C1032 Package Diagram SEATING PLANE PIN #1 ID 7 DIMENSIONS IN INCHES 1 MIN. MAX. 0.004 52-Lead Plastic Leaded Chip Carrier J69 47 8 46 0.013 0.021 0.785 0.795 0.750 0.756 0.045 0.055 20 34 21 0.690 0.730 0.023 0.033 33 0.750 0.756 0.785 0.795 0.020 MIN. 0.090 0.130 0.165 0.200 51-85004-*A Intel and Pentium are registered trademarks of Intel Corporation. All product and company names mentioned in this document are the trademarks of their respective holders. Document #: 38-05278 Rev. *A Page 12 of 13 © Cypress Semiconductor Corporation, 2004. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges. CY7C1031 CY7C1032 Document History Page Document Title: CY7C1031/CY7C1032 64K x 18 Synchronous Cache RAM Document Number: 38-05278 REV. ECN NO. Issue Date Orig. of Change Description of Change ** 114203 3/19/02 DSG Change from Spec number: 38-00219 to 38-05278 *A 212291 See ECN VBL Update ordering info by deleting CY7C1032-12 by adding EOL note to CY7C1032-10 Document #: 38-05278 Rev. *A Page 13 of 13