CY7C1041BV33-12VCT

041BV33 CY7C1041BV33 256K x 16 Static RAM Features written into the location specified on the address pins (A0 through A17). If Byte High Enable (BHE) is LOW, then data from I/O pins (I/O8 through I/O15) is written into the location specified on the address pins (A0 through A17). • High speed — tAA = 12 ns • Low active power — 612 mW (max.) • Low CMOS standby power (Commercial L version) — 1.8 mW (max.) • 2.0V Data Retention (600 µW at 2.0V retention) • Automatic power-down when deselected • TTL-compatible inputs and outputs • Easy memory expansion with CE and OE features Reading from the device is accomplished by taking Chip Enable (CE) and Output Enable (OE) LOW while forcing the Write Enable (WE) HIGH. If Byte Low Enable (BLE) is LOW, then data from the memory location specified by the address pins will appear on I/O0 to I/O7. If Byte High Enable (BHE) is LOW, then data from memory will appear on I/O8 to I/O15. See the truth table at the back of this data sheet for a complete description of read and write modes. Functional Description The CY7C1041BV33 is a high-performance CMOS Static RAM organized as 262,144 words by 16 bits. Writing to the device is accomplished by taking Chip Enable (CE) and Write Enable (WE) inputs LOW. If Byte Low Enable (BLE) is LOW, then data from I/O pins (I/O0 through I/O7), is The input/output pins (I/O0 through I/O15) are placed in a high-impedance state when the device is deselected (CE HIGH), the outputs are disabled (OE HIGH), the BHE and BLE are disabled (BHE, BLE HIGH), or during a write operation (CE LOW, and WE LOW). The CY7C1041BV33 is available in a standard 44-pin 400-mil-wide body width SOJ and 44-pin TSOP II package with center power and ground (revolutionary) pinout. Logic Block Diagram Pin Configuration SOJ TSOP II Top View 256K x 16 ARRAY 1024 x 4096 SENSE AMPS A0 A1 A2 A3 A4 A5 A6 A7 A8 ROW DECODER INPUT BUFFER A0 A1 A2 A3 A4 CE I/O0 I/O1 I/O2 I/O3 VCC VSS I/O4 I/O5 I/O6 I/O7 WE A5 A6 A7 A8 A9 I/O0 – I/O7 I/O8 – I/O15 A9 A10 A 11 A 12 A 13 A14 A15 A16 A17 COLUMN DECODER BHE WE CE OE BLE 1 44 2 3 43 42 4 41 40 39 38 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 A17 A16 A15 OE BHE BLE I/O15 I/O14 I/O13 I/O12 VSS VCC I/O11 I/O10 I/O9 I/O8 NC A14 A13 A12 A11 A10 Selection Guide -12 -15 -17 -20 -25 Maximum Access Time (ns) 12 15 17 20 25 Maximum Operating Current (mA) Comm’l 190 170 160 150 130 Ind’l - 190 180 170 150 Com’l/Ind’l 8 8 8 8 8 0.5 0.5 0.5 0.5 0.5 Maximum CMOS Standby Current (mA) Com’l Cypress Semiconductor Corporation Document #: 38-05168 Rev. ** L • 3901 North First Street • San Jose • CA 95134 • 408-943-2600 Revised November 15, 2001 CY7C1041BV33 Maximum Ratings DC Input Voltage[1] ................................ –0.5V to VCC + 0.5V (Above which the useful life may be impaired. For user guidelines, not tested.) Current into Outputs (LOW) ........................................ 20 mA Storage Temperature ................................. –65°C to +150°C Operating Range Ambient Temperature with Power Applied............................................. –55°C to +125°C Range Supply Voltage on VCC to Relative GND[1] .... –0.5V to +4.6V Commercial DC Voltage Applied to Outputs in High Z State[1] ....................................–0.5V to VCC + 0.5V Industrial Ambient Temperature[2] VCC 0°C to +70°C 3.3V ± 0.3V –40°C to +85°C Electrical Characteristics Over the Operating Range Parameter Description Test Conditions -12 Min. -15 Max. VOH Output HIGH Voltage VCC = Min., IOH = –4.0 mA 2.4 VOL Output LOW Voltage VCC = Min., IOL = 8.0 mA VIH Input HIGH Voltage 2.2 VCC + 0.5 VIL Input LOW Voltage[1] –0.5 IIX Input Load Current GND < VI < VCC IOZ Output Leakage Current GND < VOUT < VCC, Output Disabled ICC VCC Operating Supply Current VCC = Max., f = fMAX = 1/tRC ISB1 Automatic CE Power-Down Current —TTL Inputs Max. VCC, CE > VIH VIN > VIH or VIN < VIL, f = fMAX ISB2 Automatic CE Power-Down Current —CMOS Inputs Max. VCC, CE > VCC – 0.3V, VIN > VCC – 0.3V, or VIN < 0.3V, f = 0 Min. 2.4 0.4 Comm’l Ind’l Com’l/Ind’l Com’l L Max. Unit V 0.4 V 2.2 VCC + 0.5 V 0.8 –0.5 0.8 V –1 +1 –1 +1 µA –1 +1 –1 +1 µA 190 170 mA - 190 mA 40 40 mA 8 8 mA 0.5 0.5 mA Notes: 1. VIL (min.) = –2.0V for pulse durations of less than 20 ns. 2. TA is the “Instant On” case temperature. Document #: 38-05168 Rev. ** Page 2 of 11 CY7C1041BV33 Electrical Characteristics Over the Operating Range (continued) Test Conditions Parameter -17 Description -20 Min. Max. Min. VOH Output HIGH Voltage VCC = Min., IOH = –4.0 mA VOL Output LOW Voltage VCC = Min., IOL = 8.0 mA VIH Input HIGH Voltage VIL Input LOW Voltage[1] IIX Input Load Current GND < VI < VCC IOZ Output Leakage Current GND < VOUT < VCC, Output Disabled ICC VCC Operating Supply Current VCC = Max., f = fMAX = 1/tRC ISB1 Automatic CE Power-Down Current —TTL Inputs Max. VCC, CE > VIH VIN > VIH or VIN < VIL, f = fMAX ISB2 Automatic CE Power-Down Current —CMOS Inputs Max. VCC, CE > VCC – 0.3V, VIN > VCC – 0.3V, or VIN < 0.3V, f=0 2.4 -25 Max. 2.4 0.4 Min. Max. Unit 0.4 V V 2.4 0.4 V 2.2 VCC + 0.5 2.2 VCC + 0.5 2.2 VCC + 0.5 –0.5 0.8 –0.5 0.8 –0.5 0.8 V –1 +1 –1 +1 –1 +1 µA –1 +1 –1 +1 –1 +1 µA mA Comm’l 160 150 130 Ind’l 180 170 150 40 40 40 mA 8 8 8 mA 0.5 0.5 0.5 mA Com’l/Ind’l Com’l L Capacitance[3] Parameter Description CIN Input Capacitance COUT I/O Capacitance Test Conditions TA = 25°C, f = 1 MHz, VCC = 3.3V Max. Unit 8 pF 8 pF Note: 3. Tested initially and after any design or process changes that may affect these parameters. AC Test Loads and Waveforms R1 317 Ω 3.3V OUTPUT OUTPUT 30 pF ALL INPUT PULSES THÉVENIN EQUIVALENT R2 351Ω INCLUDING JIG AND SCOPE (a) Document #: 38-05168 Rev. ** 167 Ω (b) 3.3V 90% 1.73V GND Rise time: 1 V/ns 10% 90% 10% Fall time: 1 V/ns Page 3 of 11 CY7C1041BV33 Switching Characteristics[4] Over the Operating Range -12 Parameter Description Min. -15 Max. Min. -17 Max. Min. Max. Unit READ CYCLE tRC Read Cycle Time 12 15 tAA Address to Data Valid tOHA Data Hold from Address Change tACE CE LOW to Data Valid 12 tDOE OE LOW to Data Valid 6 tLZOE OE LOW to Low Z 12 3 15 ns 15 17 ns 7 8 ns 3 0 ns 0 tHZOE OE HIGH to High Z CE LOW to Low Z[6] tHZCE CE HIGH to High Z[5, 6] tPU CE LOW to Power-Up tPD CE HIGH to Power-Down 12 15 17 ns tDBE Byte Enable to Data Valid 6 7 7 ns tLZBE Byte Enable to Low Z tHZBE Byte Disable to High Z 3 7 ns tLZCE WRITE CYCLE 6 ns 17 3 0 [5, 6] 17 3 6 0 7 0 0 7 3 6 7 0 0 ns ns 0 7 ns ns ns 8 ns [7, 8] tWC Write Cycle Time 12 15 17 ns tSCE CE LOW to Write End 10 12 12 ns tAW Address Set-Up to Write End 10 12 12 ns tHA Address Hold from Write End 0 0 0 ns tSA Address Set-Up to Write Start 0 0 0 ns tPWE WE Pulse Width 10 12 12 ns tSD Data Set-Up to Write End 7 8 9 ns tHD Data Hold from Write End 0 0 0 ns tLZWE WE HIGH to Low Z[6] 3 3 3 ns [5, 6] tHZWE WE LOW to High Z tBW Byte Enable to End of Write 6 10 7 12 8 12 ns ns Notes: 4. Test conditions assume signal transition time of 3 ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V, and output loading of the specified IOL/IOH and 30-pF load capacitance. 5. tHZOE, tHZCE, and tHZWE are specified with a load capacitance of 5 pF as in part (b) of AC Test Loads. Transition is measured ±500 mV from steady-state voltage. 6. At any given temperature and voltage condition, tHZCE is less than tLZCE, tHZOE is less than tLZOE, and tHZWE is less than tLZWE for any given device. 7. The internal write time of the memory is defined by the overlap of CE LOW, and WE LOW. CE and WE must be LOW to initiate a write, and the transition of either of these signals can terminate the write. The input data set-up and hold timing should be referenced to the leading edge of the signal that terminates the write. 8. The minimum write cycle time for Write Cycle No. 3 (WE controlled, OE LOW) is the sum of tHZWE and tSD. Document #: 38-05168 Rev. ** Page 4 of 11 CY7C1041BV33 Switching Characteristics[4] Over the Operating Range (continued) -20 Parameter Description Min. -25 Max. Min. Max. Unit READ CYCLE tRC Read Cycle Time 20 25 tAA Address to Data Valid tOHA Data Hold from Address Change tACE CE LOW to Data Valid 20 25 ns tDOE OE LOW to Data Valid 8 10 ns tLZOE OE LOW to Low Z 20 25 3 5 0 OE HIGH to High Z tLZCE CE LOW to Low Z[6] tHZCE CE HIGH to High Z[5, 6] tPU CE LOW to Power-Up tPD CE HIGH to Power-Down tDBE Byte Enable to Data Valid tLZBE Byte Enable to Low Z tHZBE Byte Disable to High Z 8 ns 10 3 5 8 ns ns 0 [5, 6] tHZOE ns ns ns 10 ns 20 25 ns 8 10 ns 0 0 0 ns 0 8 ns 10 ns WRITE CYCLE[7, 8] tWC Write Cycle Time 20 25 tSCE CE LOW to Write End 13 15 ns tAW Address Set-Up to Write End 13 15 ns tHA Address Hold from Write End 0 0 ns tSA Address Set-Up to Write Start 0 0 ns tPWE WE Pulse Width 13 15 ns tSD Data Set-Up to Write End 9 10 ns tHD Data Hold from Write End 0 0 ns tLZWE WE HIGH to Low Z[6] 3 5 ns tHZWE WE LOW to High Z[5, 6] tBW Byte Enable to End of Write 8 ns 10 13 15 ns ns Data Retention Characteristics Over the Operating Range (For L version only) Parameter Conditions[10] Description VDR VCC for Data Retention ICCDR Data Retention Current tCDR[3] Chip Deselect to Data Retention Time tR[9] Operation Recovery Time Min. Max. 2.0 VCC = VDR = 2.0V, CE > VCC – 0.3V, VIN > VCC – 0.3V or VIN < 0.3V Unit V 330 µA 0 ns tRC ns Notes: 9. tr < 3 ns for the -12 and -15 speeds. tr < 5 ns for the -20 and slower speeds. 10. No input may exceed VCC + 0.5V. Document #: 38-05168 Rev. ** Page 5 of 11 CY7C1041BV33 Data Retention Waveform DATA RETENTION MODE 3.0V VCC VDR > 2V 3.0V tR tCDR CE 1041BV33– Switching Waveforms [11, 12] Read Cycle No. 1 tRC ADDRESS tAA tOHA DATA OUT PREVIOUS DATA VALID DATA VALID 1041BV33-6 Read Cycle No. 2 (OE Controlled) [12, 13] ADDRESS tRC CE tACE OE tHZOE tDOE BHE, BLE tLZOE tHZCE tDBE tLZBE DATA OUT HIGH IMPEDANCE tLZCE VCC SUPPLY CURRENT tHZBE HIGH IMPEDANCE DATA VALID tPD tPU 50% IICC CC 50% IISB SB 1041BV33-7 Notes: 11. Device is continuously selected. OE, CE, BHE and/or BHE = VIL. 12. WE is HIGH for read cycle. 13. Address valid prior to or coincident with CE transition LOW. Document #: 38-05168 Rev. ** Page 6 of 11 CY7C1041BV33 Switching Waveforms (continued) [14, 15] Write Cycle No. 1 (CE Controlled) tWC ADDRESS CE tSA tSCE tAW tHA tPWE WE tBW BHE, BLE tSD tHD DATAI/O 1041BV33-8 Write Cycle No. 2 (BLE or BHE Controlled) tWC ADDRESS BHE, BLE tSA tBW tAW tHA tPWE WE tSCE CE tSD tHD DATAI/O 1041BV33-9 Notes: 14. Data I/O is high-impedance if OE or BHE and/or BLE= VIH. 15. If CE goes HIGH simultaneously with WE going HIGH, the output remains in a high–impedance state. Document #: 38-05168 Rev. ** Page 7 of 11 CY7C1041BV33 Switching Waveforms (continued) Write Cycle No.3 (WE Controlled, OE LOW) tWC ADDRESS tSCE CE tAW tHA tSA tPWE WE tBW BHE, BLE tHZWE tSD tHD DATA I/O tLZWE 1041BV33-10 Truth Table CE OE WE BLE BHE H L I/O0–I/O7 I/O8–I/O15 Mode Power X X X X High Z High Z Power Down Standby (ISB) L H L L Data Out Data Out Read All Bits Active (ICC) L L H L H Data Out High Z Read Lower Bits Only Active (ICC) L L H H L High Z Data Out Read Upper Bits Only Active (ICC) L X L L L Data In Data In Write All Bits Active (ICC) L X L L H Data In High Z Write Lower Bits Only Active (ICC) L X L H L High Z Data In Write Upper Bits Only Active (ICC) L H H X X High Z High Z Selected, Outputs Disabled Active (ICC) Document #: 38-05168 Rev. ** Page 8 of 11 CY7C1041BV33 Ordering Information Speed (ns) 12 15 17 20 25 Ordering Code CY7C1041BV33-12VC CY7C1041BV33L-12VC CY7C1041BV33-12ZC CY7C1041BV33L-12ZC CY7C1041BV33-15VC CY7C1041BV33L-15VC CY7C1041BV33-15ZC CY7C1041BV33L-15ZC CY7C1041BV33-15VI CY7C1041BV33-15ZI CY7C1041BV33-17VC CY7C1041BV33L-17VC CY7C1041BV33-17ZC CY7C1041BV33L-17ZC CY7C1041BV33-17VI CY7C1041BV33-17ZI CY7C1041BV33-20VC CY7C1041BV33L-20VC CY7C1041BV33-20ZC CY7C1041BV33L-20ZC CY7C1041BV33-20VI CY7C1041BV33-20ZI CY7C1041BV33-25VC CY7C1041BV33L-25VC CY7C1041BV33-25ZC CY7C1041BV33L-25ZC CY7C1041BV33-25VI CY7C1041BV33-25ZI Document #: 38-05168 Rev. ** Package Name V34 V34 Z44 Z44 V34 V34 Z44 Z44 V34 Z44 V34 V34 Z44 Z44 V34 Z44 V34 V34 Z44 Z44 V34 Z44 V34 V34 Z44 Z44 V34 Z44 Package Type 44-Lead (400-Mil) Molded SOJ 44-Lead (400-Mil) Molded SOJ 44-Pin TSOP II Z44 44-Pin TSOP II Z44 44-Lead (400-Mil) Molded SOJ 44-Lead (400-Mil) Molded SOJ 44-Pin TSOP II Z44 44-Pin TSOP II Z44 44-Lead (400-Mil) Molded SOJ 44-Pin TSOP II Z44 44-Lead (400-Mil) Molded SOJ 44-Lead (400-Mil) Molded SOJ 44-Pin TSOP II Z44 44-Pin TSOP II Z44 44-Lead (400-Mil) Molded SOJ 44-Pin TSOP II Z44 44-Lead (400-Mil) Molded SOJ 44-Lead (400-Mil) Molded SOJ 44-Pin TSOP II Z44 44-Pin TSOP II Z44 44-Lead (400-Mil) Molded SOJ 44-Pin TSOP II Z44 44-Lead (400-Mil) Molded SOJ 44-Lead (400-Mil) Molded SOJ 44-Pin TSOP II Z44 44-Pin TSOP II Z44 44-Lead (400-Mil) Molded SOJ 44-Pin TSOP II Z44 Operating Range Commercial Commercial Industrial Commercial Industrial Commercial Industrial Commercial Industrial Page 9 of 11 CY7C1041BV33 Package Diagrams 44-Lead (400-Mil) Molded SOJ V34 51-85082-B 44-Pin TSOP II Z44 51-85087-A Document #: 38-05168 Rev. ** Page 10 of 11 © Cypress Semiconductor Corporation, 2001. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges. CY7C1041BV33 Document Title: CY7C1041BV33 256K x 16 SRAM Document Number: 38-05168 REV. ECN NO. Issue Date Orig. of Change Description of Change ** 111840 11/17/01 DSG Change from Spec number: 38-00932 to 38-05168 Document #: 38-05168 Rev. ** Page 11 of 11