Please note that Cypress is an Infineon Technologies Company.
The document following this cover page is marked as “Cypress” document as this is the
company that originally developed the product. Please note that Infineon will continue
to offer the product to new and existing customers as part of the Infineon product
portfolio.
Continuity of document content
The fact that Infineon offers the following product as part of the Infineon product
portfolio does not lead to any changes to this document. Future revisions will occur
when appropriate, and any changes will be set out on the document history page.
Continuity of ordering part numbers
Infineon continues to support existing part numbers. Please continue to use the
ordering part numbers listed in the datasheet for ordering.
www.infineon.com
CY7C1354CV25
CY7C1356CV25
9-Mbit (256K × 36/512K × 18)
Pipelined SRAM with NoBL™ Architecture
9-Mbit (256K × 36/512K × 18) Pipelined SRAM with NoBL™ Architecture
Features
Functional Description
■
Pin-compatible with and functionally equivalent to ZBT™
■
Supports 250 MHz bus operations with zero wait states
■
Available speed grades are 250, 200, and 166 MHz
■
Internally self-timed output buffer control to eliminate the need
to use asynchronous OE
■
Fully registered (inputs and outputs) for pipelined operation
■
Byte write capability
■
Single 2.5 V power supply (VDD)
■
Fast clock-to-output times
❐ 2.8 ns (for 250-MHz device)
■
Clock enable (CEN) pin to suspend operation
■
Synchronous self-timed writes
■
Available in Pb-free 100-pin TQFP package, Pb-free and
non Pb-free 119-ball BGA package and 165-ball FBGA
package
■
IEEE 1149.1 JTAG-compatible boundary scan
■
Burst capability – linear or interleaved burst order
■
“ZZ” sleep mode option and stop clock option
The
CY7C1354CV25/CY7C1356CV25[1]
are
2.5 V,
256K × 36/512K × 18 synchronous pipelined burst SRAMs with
No Bus Latency™ (NoBL™) logic, respectively. They are
designed to support unlimited true back-to-back read/write
operations
with
no
wait
states.
The
CY7C1354CV25/CY7C1356CV25 are equipped with the
advanced (NoBL) logic required to enable consecutive
read/write operations with data being transferred on every clock
cycle. This feature dramatically improves the throughput of data
in systems that require frequent write/read transitions. The
CY7C1354CV25/CY7C1356CV25 are pin-compatible with and
functionally equivalent to ZBT devices.
All synchronous inputs pass through input registers controlled by
the rising edge of the clock. All data outputs pass through output
registers controlled by the rising edge of the clock. The clock
input is qualified by the clock enable (CEN) signal, which when
deasserted suspends operation and extends the previous clock
cycle.
Write operations are controlled by the byte write selects
(BWa–BWd for CY7C1354CV25 and BWa–BWb for
CY7C1356CV25) and a write enable (WE) input. All writes are
conducted with on-chip synchronous self-timed write circuitry.
Three synchronous chip enables (CE1, CE2, CE3) and an
asynchronous output enable (OE) provide for easy bank
selection and output tri-state control. In order to avoid bus
contention, the output drivers are synchronously tri-stated during
the data portion of a write sequence.
For a complete list of related documentation, click here.
Selection Guide
250 MHz
200 MHz
166 MHz
Unit
Maximum access time
Description
2.8
3.2
3.5
ns
Maximum operating current
250
220
180
mA
Maximum CMOS standby current
40
40
40
mA
Note
1. For best-practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com.
Cypress Semiconductor Corporation
Document Number: 38-05537 Rev. *S
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised April 5, 2019
CY7C1354CV25
CY7C1356CV25
Logic Block Diagram – CY7C1354CV25
A0, A1, A
ADDRESS
REGISTER 0
A1
A1'
D1
Q1
A0
A0'
BURST
D0
Q0
LOGIC
MODE
CLK
CEN
ADV/LD
C
C
WRITE ADDRESS
REGISTER 1
WRITE ADDRESS
REGISTER 2
ADV/LD
BWa
BWb
BWc
BWd
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
WRITE
DRIVERS
MEMORY
ARRAY
WE
S
E
N
S
E
A
M
P
S
O
U
T
P
U
T
R
E
G
I
S
T
E
R
S
E
INPUT
REGISTER 1 E
OE
CE1
CE2
CE3
ZZ
Document Number: 38-05537 Rev. *S
O
U
T
P
U
T
D
A
T
A
S
T
E
E
R
I
N
G
INPUT
REGISTER 0
B
U
F
F
E
R
S
DQs
DQPa
DQPb
DQPc
DQPd
E
E
READ LOGIC
SLEEP
CONTROL
Page 2 of 35
CY7C1354CV25
CY7C1356CV25
Logic Block Diagram – CY7C1356CV25
A0, A1, A
ADDRESS
REGISTER 0
A1
A1'
D1
Q1
A0
BURST A0'
D0
Q0
LOGIC
MODE
CLK
CEN
ADV/LD
C
C
WRITE ADDRESS
REGISTER 1
WRITE ADDRESS
REGISTER 2
ADV/LD
BWa
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
WRITE
DRIVERS
MEMORY
ARRAY
BWb
WE
S
E
N
S
E
A
M
P
S
O
U
T
P
U
T
R
E
G
I
S
T
E
R
S
D
A
T
A
S
T
E
E
R
I
N
G
E
INPUT
REGISTER 1 E
OE
CE1
CE2
CE3
ZZ
Document Number: 38-05537 Rev. *S
O
U
T
P
U
T
B
U
F
F
E
R
S
DQs
DQPa
DQPb
E
INPUT
REGISTER 0 E
READ LOGIC
Sleep
Control
Page 3 of 35
CY7C1354CV25
CY7C1356CV25
Contents
Pin Configurations ........................................................... 5
Pin Definitions .................................................................. 8
Functional Overview ........................................................ 9
Single Read Accesses ................................................ 9
Burst Read Accesses .................................................. 9
Single Write Accesses ................................................. 9
Burst Write Accesses ................................................ 10
Sleep Mode ............................................................... 10
Interleaved Burst Address Table ............................... 10
Linear Burst Address Table ....................................... 10
ZZ Mode Electrical Characteristics ............................ 10
Truth Table ...................................................................... 11
Partial Truth Table for Read/Write ................................ 12
Partial Truth Table for Read/Write ................................ 12
IEEE 1149.1 Serial Boundary Scan (JTAG) .................. 13
Disabling the JTAG Feature ...................................... 13
Test Access Port (TAP) ............................................. 13
PERFORMING A TAP RESET .................................. 13
TAP REGISTERS ...................................................... 13
TAP Instruction Set ................................................... 14
TAP Controller State Diagram ....................................... 15
TAP Controller Block Diagram ...................................... 16
TAP Timing ...................................................................... 16
TAP AC Switching Characteristics ............................... 17
2.5 V TAP AC Test Conditions ....................................... 17
2.5 V TAP AC Output Load Equivalent ......................... 17
TAP DC Electrical Characteristics
and Operating Conditions ............................................. 18
Document Number: 38-05537 Rev. *S
Identification Register Definitions ................................ 18
Scan Register Sizes ....................................................... 18
Instruction Codes ........................................................... 18
Boundary Scan Exit Order ............................................. 19
Boundary Scan Exit Order ............................................. 20
Maximum Ratings ........................................................... 21
Operating Range ............................................................. 21
Electrical Characteristics ............................................... 21
Capacitance .................................................................... 22
Thermal Resistance ........................................................ 22
AC Test Loads and Waveforms ..................................... 22
Switching Characteristics .............................................. 23
Switching Waveforms .................................................... 24
Ordering Information ...................................................... 27
Ordering Code Definitions ......................................... 27
Package Diagrams .......................................................... 28
Acronyms ........................................................................ 31
Document Conventions ................................................. 31
Units of Measure ....................................................... 31
Document History Page ................................................. 32
Sales, Solutions, and Legal Information ...................... 35
Worldwide Sales and Design Support ....................... 35
Products .................................................................... 35
PSoC® Solutions ...................................................... 35
Cypress Developer Community ................................. 35
Technical Support ..................................................... 35
Page 4 of 35
CY7C1354CV25
CY7C1356CV25
Pin Configurations
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
CY7C1356CV25
(512K × 18)
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
A
NC
NC
VDDQ
VSS
NC
DQPa
DQa
DQa
VSS
VDDQ
DQa
DQa
VSS
NC
VDD
ZZ
DQa
DQa
VDDQ
VSS
DQa
DQa
NC
NC
VSS
VDDQ
NC
NC
NC
A
A
A
A
A
A
A
NC(72M)
NC(36M)
VSS
VDD
NC(288M)
NC(144M)
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
NC
DQPb
NC
DQb
NC
DQb
VDDQ VDDQ
VSS
VSS
NC
DQb
DQb
NC
DQb
DQb
DQb
DQb
VSS
VSS
VDDQ VDDQ
DQb
DQb
DQb
DQb
NC
VSS
VDD
NC
VDD
NC
VSS
ZZ
DQb
DQa
DQa
DQb
VDDQ VDDQ
VSS
VSS
DQa
DQb
DQa
DQb
DQa DQPb
DQa
NC
VSS
VSS
VDDQ VDDQ
NC
DQa
DQa
NC
DQPa
NC
MODE
A
A
A
A
A1
A0
Document Number: 38-05537 Rev. *S
A
A
A
A
A
A
A
NC(72M)
NC(36M)
VSS
DQd
DQd
VDDQ
VSS
DQd
DQd
DQd
DQd
VSS
VDDQ
DQd
DQd
DQPd
CY7C1354CV25
(256K × 36)
VSS
VDD
NC
NC(288M)
NC(144M)
DQc
DQc
NC
VDD
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
VSS
DQc
DQc
DQc
DQc
VSS
VDDQ
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MODE
A
A
A
A
A1
A0
DQPc
DQc
DQc
VDDQ
A
A
A
A
CE1
CE2
NC
NC
BWb
BWa
CE3
VDD
VSS
CLK
WE
CEN
OE
ADV/LD
NC(18M)
A
A
A
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
A
A
CE1
CE2
BWd
BWc
BWb
BWa
CE3
VDD
VSS
CLK
WE
CEN
OE
ADV/LD
NC(18M)
A
Figure 1. 100-pin TQFP (14 × 20 × 1.4 mm) pinout
Page 5 of 35
CY7C1354CV25
CY7C1356CV25
Pin Configurations (continued)
Figure 2. 119-ball BGA (14 × 22 × 2.4 mm) pinout
CY7C1354CV25 (256K × 36)
1
2
3
4
5
6
7
A
VDDQ
A
A
NC/18M
A
A
VDDQ
B
C
D
E
F
G
H
J
K
L
M
N
P
NC/576M
NC/1G
DQc
CE2
A
DQPc
A
A
VSS
ADV/LD
VDD
NC
A
A
VSS
CE3
A
DQPb
NC
NC
DQb
DQc
DQc
VSS
CE1
VSS
DQb
DQb
VDDQ
DQc
VSS
DQb
VDDQ
DQc
BWb
DQb
DQb
DQc
VDDQ
DQc
VDD
BWc
VSS
NC
OE
A
VSS
DQc
WE
VDD
VSS
NC
DQb
VDD
DQb
VDDQ
DQd
DQd
DQd
DQd
CLK
NC
VSS
BWd
BWa
DQa
DQa
DQa
DQa
VDDQ
DQd
VSS
DQa
VDDQ
DQd
VSS
CEN
A1
VSS
DQd
VSS
DQa
DQa
DQd
DQPd
VSS
A0
VSS
DQPa
DQa
R
T
U
NC/144M
A
MODE
VDD
NC/288M
NC/72M
A
A
NC
A
A
NC
NC/36M
ZZ
VDDQ
TMS
TDI
TCK
TDO
NC
VDDQ
VSS
CY7C1356CV25 (512K × 18)
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
1
2
3
4
5
6
7
VDDQ
A
A
NC/18M
A
A
VDDQ
NC/576M
CE2
A
A
A
CE3
A
NC
A
ADV/LD
VDD
A
NC/1G
DQb
NC
VSS
NC
VSS
DQPa
NC
CE1
VSS
NC
DQa
OE
A
VSS
DQa
VDDQ
VSS
VSS
NC
NC
DQa
VDD
DQa
NC
VDDQ
DQa
NC
DQb
VSS
VDDQ
NC
VSS
NC
DQb
VDDQ
DQb
NC
VDD
BWb
VSS
NC
WE
VDD
NC
NC
DQb
VSS
CLK
VSS
NC
DQb
NC
VSS
NC
DQa
NC
VDDQ
DQb
VSS
NC
VDDQ
DQb
NC
VSS
CEN
A1
BWa
VSS
VSS
DQa
NC
NC
DQPb
VSS
A0
VSS
NC
DQa
NC/144M
A
MODE
VDD
NC
A
NC/288M
NC/72M
A
A
NC/36M
A
A
ZZ
VDDQ
TMS
TDI
TCK
TDO
NC
VDDQ
Document Number: 38-05537 Rev. *S
Page 6 of 35
CY7C1354CV25
CY7C1356CV25
Pin Configurations (continued)
Figure 3. 165-ball FBGA (13 × 15 × 1.4 mm) pinout
CY7C1354CV25 (256K × 36)
1
2
3
4
5
6
7
8
9
10
11
A
B
C
D
E
F
G
H
J
K
L
M
N
P
NC/576M
A
CE1
BWc
BWb
CE3
ADV/LD
A
A
NC
BWa
VSS
CLK
CEN
WE
OE
NC/18M
VSS
VSS
VSS
VSS
VSS
VDD
VDDQ
VDDQ
A
NC
DQb
DQPb
DQb
R
MODE
NC/1G
A
CE2
DQPc
DQc
NC
DQc
VDDQ
VDDQ
BWd
VSS
VDD
DQc
DQc
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQb
DQb
DQc
DQc
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQb
DQb
DQc
NC
DQd
DQc
NC
DQd
VDDQ
NC
VDDQ
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDDQ
VDDQ
DQb
NC
DQa
DQb
ZZ
DQa
DQd
DQd
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQa
DQa
DQd
DQd
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQa
DQa
DQd
DQPd
DQd
NC
VDDQ
VDDQ
VDD
VSS
VSS
NC
VSS
NC
VSS
NC
VDD
VSS
VDDQ
VDDQ
DQa
NC
DQa
DQPa
A
A
TDI
A1
TDO
A
A
A
NC/288M
A
A
TMS
A0
TCK
A
A
A
A
NC/144M NC/72M
NC/36M
VSS
NC
NC
CY7C1356CV25 (512K × 18)
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
3
4
5
6
7
8
9
10
11
NC/576M
A
CE1
BWb
NC
CE3
CEN
ADV/LD
A
A
A
DQPa
DQa
NC/1G
A
CE2
NC
BWa
CLK
NC
DQb
VDDQ
VSS
VDDQ
VSS
VDD
VSS
VSS
VSS
WE
VSS
VSS
OE
VSS
VDD
NC/18M
NC
NC
VDDQ
A
NC
NC
VDDQ
NC
NC
DQb
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
NC
DQa
NC
DQb
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
NC
DQa
NC
NC
DQb
DQb
NC
NC
VDDQ
NC
VDDQ
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDDQ
VDDQ
NC
NC
DQa
DQa
ZZ
NC
DQb
NC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQa
NC
DQb
NC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQa
NC
DQb
DQPb
NC
NC
VDDQ
VDDQ
VDD
VSS
VSS
NC
VSS
NC
VSS
NC
VDD
VSS
VDDQ
VDDQ
DQa
NC
NC
NC
NC/144M NC/72M
A
A
TDI
A1
TDO
A
A
A
NC/36M
A
A
TMS
A0
TCK
A
A
A
MODE
Document Number: 38-05537 Rev. *S
NC
NC/288M
A
Page 7 of 35
CY7C1354CV25
CY7C1356CV25
Pin Definitions
Pin Name
A0, A1, A
I/O Type
Pin Description
InputAddress inputs used to select one of the address locations. Sampled at the rising edge of the CLK.
synchronous
BWa, BWb,
InputByte write select inputs, active LOW. Qualified with WE to conduct writes to the SRAM. Sampled on
BWc, BWd synchronous the rising edge of CLK. BWa controls DQa and DQPa, BWb controls DQb and DQPb, BWc controls DQc
and DQPc, BWd controls DQd and DQPd.
WE
InputWrite enable input, active LOW. Sampled on the rising edge of CLK if CEN is active LOW. This signal
synchronous must be asserted LOW to initiate a write sequence.
ADV/LD
InputAdvance/load input used to advance the on-chip address counter or load a new address. When
synchronous HIGH (and CEN is asserted LOW) the internal burst counter is advanced. When LOW, a new address
can be loaded into the device for an access. After being deselected, ADV/LD should be driven LOW in
order to load a new address.
CLK
Inputclock
Clock input. Used to capture all synchronous inputs to the device. CLK is qualified with CEN. CLK is
only recognized if CEN is active LOW.
CE1
InputChip enable 1 input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE2
synchronous and CE3 to select/deselect the device.
CE2
InputChip enable 2 input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction with CE1
synchronous and CE3 to select/deselect the device.
CE3
InputChip enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE1
synchronous and CE2 to select/deselect the device.
OE
InputOutput enable, active LOW. Combined with the synchronous logic block inside the device to control
asynchronous the direction of the I/O pins. When LOW, the I/O pins are allowed to behave as outputs. When deasserted
HIGH, I/O pins are tri-stated, and act as input data pins. OE is masked during the data portion of a write
sequence, during the first clock when emerging from a deselected state and when the device has been
deselected.
CEN
InputClock enable input, active LOW. When asserted LOW the clock signal is recognized by the SRAM.
synchronous When deasserted HIGH the clock signal is masked. Since deasserting CEN does not deselect the device,
CEN can be used to extend the previous cycle when required.
DQS
I/OBidirectional data I/O lines. As inputs, they feed into an on-chip data register that is triggered by the
synchronous rising edge of CLK. As outputs, they deliver the data contained in the memory location specified by
addresses during the previous clock rise of the read cycle. The direction of the pins is controlled by OE
and the internal control logic. When OE is asserted LOW, the pins can behave as outputs. When HIGH,
DQa–DQd are placed in a tri-state condition. The outputs are automatically tri-stated during the data
portion of a write sequence, during the first clock when emerging from a deselected state, and when the
device is deselected, regardless of the state of OE.
DQPX
I/OBidirectional data parity I/O lines. Functionally, these signals are identical to DQ[a:d]. During write
synchronous sequences, DQPa is controlled by BWa, DQPb is controlled by BWb, DQPc is controlled by BWc, and
DQPd is controlled by BWd.
MODE
Input strap pin Mode input. Selects the burst order of the device. Tied HIGH selects the interleaved burst order. Pulled
LOW selects the linear burst order. MODE should not change states during operation. When left floating
MODE will default HIGH, to an interleaved burst order.
TDO
JTAG serial Serial data-out to the JTAG circuit. Delivers data on the negative edge of TCK.
output
synchronous
TDI
JTAG serial Serial data-in to the JTAG circuit. Sampled on the rising edge of TCK.
input
synchronous
TMS
Test mode This pin controls the test access port state machine. Sampled on the rising edge of TCK.
select
synchronous
Document Number: 38-05537 Rev. *S
Page 8 of 35
CY7C1354CV25
CY7C1356CV25
Pin Definitions (continued)
Pin Name
TCK
VDD
VDDQ
I/O Type
JTAG-clock
Pin Description
Clock input to the JTAG circuitry.
Power supply Power supply inputs to the core of the device.
I/O power
supply
Power supply for the I/O circuitry.
VSS
Ground
NC
–
No connects. This pin is not connected to the die.
NC/18M,
NC/36M,
NC/72M,
NC/144M,
NC/288M,
NC/576M,
NC/1G
–
These pins are not connected. They will be used for expansion to the 18M, 36M, 72M, 144M 288M,
576M, and 1G densities.
ZZ
Ground for the device. Should be connected to ground of the system.
InputZZ “sleep” Input. This active HIGH input places the device in a non-time critical “sleep” condition with
asynchronous data integrity preserved. For normal operation, this pin has to be LOW or left floating. ZZ pin has an
internal pull-down.
Functional Overview
The
CY7C1354CV25/CY7C1356CV25
are
synchronous-pipelined burst NoBL SRAMs designed specifically
to eliminate wait states during write/read transitions. All
synchronous inputs pass through input registers controlled by
the rising edge of the clock. The clock signal is qualified with the
clock enable input signal (CEN). If CEN is HIGH, the clock signal
is not recognized and all internal states are maintained. All
synchronous operations are qualified with CEN. All data outputs
pass through output registers controlled by the rising edge of the
clock. Maximum access delay from the clock rise (tCO) is 2.8 ns
(250-MHz device).
Accesses can be initiated by asserting all three chip enables
(CE1, CE2, CE3) active at the rising edge of the clock. If clock
enable (CEN) is active LOW and ADV/LD is asserted LOW, the
address presented to the device will be latched. The access can
either be a read or write operation, depending on the status of
the write enable (WE). BW[d:a] can be used to conduct byte write
operations.
Write operations are qualified by the write enable (WE). All writes
are simplified with on-chip synchronous self-timed write circuitry.
Three synchronous chip enables (CE1, CE2, CE3) and an
asynchronous output enable (OE) simplify depth expansion. All
operations (reads, writes, and deselects) are pipelined. ADV/LD
should be driven LOW once the device has been deselected in
order to load a new address for the next operation.
Single Read Accesses
A read access is initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2,
and CE3 are all asserted active, (3) the write enable input signal
WE is deasserted HIGH, and (4) ADV/LD is asserted LOW. The
address presented to the address inputs is latched into the
address register and presented to the memory core and control
logic. The control logic determines that a read access is in
progress and allows the requested data to propagate to the input
of the output register. At the rising edge of the next clock the
Document Number: 38-05537 Rev. *S
requested data is allowed to propagate through the output
register and onto the data bus within 2.8 ns (250-MHz device)
provided OE is active LOW. After the first clock of the read
access the output buffers are controlled by OE and the internal
control logic. OE must be driven LOW in order for the device to
drive out the requested data. During the second clock, a
subsequent operation (read/write/deselect) can be initiated.
Deselecting the device is also pipelined. Therefore, when the
SRAM is deselected at clock rise by one of the chip enable
signals, its output will tri-state following the next clock rise.
Burst Read Accesses
The CY7C1354CV25/CY7C1356CV25 have an on-chip burst
counter that allows the user the ability to supply a single address
and conduct up to four reads without reasserting the address
inputs. ADV/LD must be driven LOW in order to load a new
address into the SRAM, as described in Single Read Accesses.
The sequence of the burst counter is determined by the MODE
input signal. A LOW input on MODE selects a linear burst mode,
a HIGH selects an interleaved burst sequence. Both burst
counters use A0 and A1 in the burst sequence, and will wrap
around when incremented sufficiently. A HIGH input on ADV/LD
will increment the internal burst counter regardless of the state
of chip enables inputs or WE. WE is latched at the beginning of
a burst cycle. Therefore, the type of access (read or write) is
maintained throughout the burst sequence.
Single Write Accesses
Write access are initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2,
and CE3 are all asserted active, and (3) the write signal WE is
asserted LOW. The address presented to A0–A16 is loaded into
the address register. The write signals are latched into the
control logic block.
On the subsequent clock rise the data lines are automatically
tri-stated regardless of the state of the OE input signal. This
allows the external logic to present the data on DQ and DQP
(DQa,b,c,d/DQPa,b,c,d for CY7C1354CV25 and DQa,b/DQPa,b for
Page 9 of 35
CY7C1354CV25
CY7C1356CV25
CY7C1356CV25). In addition, the address for the subsequent
access (read/write/deselect) is latched into the address register
(provided the appropriate control signals are asserted).
On the next clock rise the data presented to DQ and DQP
(DQa,b,c,d/DQPa,b,c,d for CY7C1354CV25 and DQa,b/DQPa,b for
CY7C1356CV25) (or a subset for byte write operations, see
Write Cycle Description table for details) inputs is latched into the
device and the Write is complete.
The data written during the write operation is controlled by BW
(BWa,b,c,d for CY7C1354CV25 and BWa,b for CY7C1356CV25)
signals. The CY7C1354CV25/CY7C1356CV25 provides byte
write capability that is described in the Write Cycle Description
table. Asserting the write enable input (WE) with the selected
byte write select (BW) input will selectively write to only the
desired bytes. Bytes not selected during a byte write operation
will remain unaltered. A synchronous self-timed write
mechanism has been provided to simplify the write operations.
Byte write capability has been included in order to greatly simplify
read/modify/write sequences, which can be reduced to simple
byte write operations.
Because the CY7C1354CV25/CY7C1356CV25 are common I/O
devices, data should not be driven into the device while the
outputs are active. The output enable (OE) can be deasserted
HIGH before presenting data to the DQ and DQP
(DQa,b,c,d/DQPa,b,c,d for CY7C1354CV25 and DQa,b/DQPa,b for
CY7C1356CV25) inputs. Doing so will tri-state the output drivers.
As a safety precaution, DQ and DQP (DQa,b,c,d/DQPa,b,c,d for
CY7C1354CV25 and DQa,b/DQPa,b for CY7C1356CV25) are
automatically tri-stated during the data portion of a write cycle,
regardless of the state of OE.
Burst Write Accesses
The CY7C1354CV25/CY7C1356CV25 has an on-chip burst
counter that allows the user the ability to supply a single address
and conduct up to four write operations without reasserting the
address inputs. ADV/LD must be driven LOW in order to load the
initial address, as described in Single Write Accesses on page 9.
When ADV/LD is driven HIGH on the subsequent clock rise, the
chip enables (CE1, CE2, and CE3) and WE inputs are ignored
and the burst counter is incremented. The correct BW (BWa,b,c,d
for CY7C1354CV25 and BWa,b for CY7C1356CV25) inputs must
be driven in each cycle of the burst write in order to write the
correct bytes of data.
Sleep Mode
The ZZ input pin is an asynchronous input. Asserting ZZ places
the SRAM in a power conservation “sleep” mode. Two clock
cycles are required to enter into or exit from this “sleep” mode.
While in this mode, data integrity is guaranteed. Accesses
pending when entering the “sleep” mode are not considered valid
nor is the completion of the operation guaranteed. The device
must be deselected prior to entering the “sleep” mode. CE1, CE2,
and CE3, must remain inactive for the duration of tZZREC after the
ZZ input returns LOW.
Interleaved Burst Address Table
(MODE = Floating or VDD)
First
Address
A1, A0
Second
Address
A1, A0
Third
Address
A1, A0
Fourth
Address
A1, A0
00
01
10
11
01
00
11
10
10
11
00
01
11
10
01
00
Linear Burst Address Table
(MODE = GND)
First
Address
A1, A0
Second
Address
A1, A0
Third
Address
A1, A0
Fourth
Address
A1, A0
00
01
10
11
01
10
11
00
10
11
00
01
11
00
01
10
ZZ Mode Electrical Characteristics
Parameter
IDDZZ
Description
Sleep mode standby current
Test Conditions
ZZ VDD 0.2 V
tZZS
Device operation to ZZ
ZZ VDD 0.2 V
tZZREC
ZZ recovery time
ZZ 0.2 V
tZZI
ZZ active to sleep current
This parameter is sampled
tRZZI
ZZ Inactive to exit sleep current
This parameter is sampled
Document Number: 38-05537 Rev. *S
Min
–
Max
50
Unit
mA
–
2tCYC
ns
2tCYC
–
ns
–
2tCYC
ns
0
–
ns
Page 10 of 35
CY7C1354CV25
CY7C1356CV25
Truth Table
The truth table for CY7C1354CV25/CY7C1356CV25 follows. [2, 3, 4, 5, 6, 7, 8]
Operation
Address used CE ZZ ADV/LD WE BWx OE CEN CLK
DQ
Deselect cycle
None
H
L
L
X
X
X
L
L–H
Tri-state
Continue deselect cycle
None
X
L
H
X
X
X
L
L–H
Tri-state
Read cycle (begin burst)
External
L
L
L
H
X
L
L
L–H Data out (Q)
Next
X
L
H
X
X
L
L
L–H Data out (Q)
External
L
L
L
H
X
H
L
L–H
Tri-state
Next
X
L
H
X
X
H
L
L–H
Tri-state
External
L
L
L
L
L
X
L
L–H
Data in (D)
Write cycle (continue burst)
Next
X
L
H
X
L
X
L
L–H
Data in (D)
NOP/write abort (begin burst)
None
L
L
L
L
H
X
L
L–H
Tri-state
Write abort (continue burst)
Next
X
L
H
X
H
X
L
L–H
Tri-state
Current
X
L
X
X
X
X
H
L–H
–
None
X
H
X
X
X
X
X
X
Tri-state
Read cycle (continue burst)
NOP/dummy read (begin burst)
Dummy read (continue burst)
Write cycle (begin burst)
Ignore clock edge (stall)
Sleep mode
Notes
2. X = “Don’t Care”, H = Logic HIGH, L = Logic LOW, CE stands for all chip enables active. BWx = L signifies at least one byte write select is active, BWx = Valid signifies
that the desired byte write selects are asserted, see Write Cycle Description table for details.
3. Write is defined by WE and BWX. See Write Cycle Description table for details.
4. When a write cycle is detected, all I/Os are tri-stated, even during byte writes.
5. The DQ and DQP pins are controlled by the current cycle and the OE signal.
6. CEN = H inserts wait states.
7. Device will power-up deselected and the I/Os in a tri-state condition, regardless of OE.
8. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle DQs and DQPX = tri-state when OE is
inactive or when the device is deselected, and DQs = data when OE is active.
Document Number: 38-05537 Rev. *S
Page 11 of 35
CY7C1354CV25
CY7C1356CV25
Partial Truth Table for Read/Write
The partial truth table for Read/Write for CY7C1354CV25 follows. [9, 10, 11, 12]
Function (CY7C1354CV25)
WE
BWd
BWc
BWb
BWa
Read
H
X
X
X
X
Write– no bytes written
L
H
H
H
H
Write byte a–(DQa and DQPa)
L
H
H
H
L
Write byte b – (DQb and DQPb)
L
H
H
L
H
Write bytes b, a
L
H
H
L
L
Write byte c –(DQc and DQPc)
L
H
L
H
H
Write bytes c, a
L
H
L
H
L
Write bytes c, b
L
H
L
L
H
Write bytes c, b, a
L
H
L
L
L
Write byte d –(DQd and DQPd)
L
L
H
H
H
Write bytes d, a
L
L
H
H
L
Write bytes d, b
L
L
H
L
H
Write bytes d, b, a
L
L
H
L
L
Write bytes d, c
L
L
L
H
H
Write bytes d, c, a
L
L
L
H
L
Write bytes d, c, b
L
L
L
L
H
Write all bytes
L
L
L
L
L
Partial Truth Table for Read/Write
The partial truth table for Read/Write for CY7C1356CV25 follows. [9, 10, 11, 12]
Function (CY7C1356CV25)
WE
BWb
BWa
Read
H
x
x
Write – no bytes written
L
H
H
Write byte a (DQa and DQPa)
L
H
L
Write byte b – (DQb and DQPb)
L
L
H
Write both bytes
L
L
L
Notes
9. X = “Don’t Care”, H = Logic HIGH, L = Logic LOW, CE stands for all chip enables active. BWx = L signifies at least one byte write select is active, BWx = valid signifies
that the desired byte write selects are asserted, see Write Cycle Description table for details.
10. Write is defined by WE and BWX. See Write Cycle Description table for details.
11. When a write cycle is detected, all I/Os are tri-stated, even during byte writes.
12. Table only lists a partial listing of the byte write combinations. Any combination of BWX is valid. Appropriate write will be done based on which byte write is active.
Document Number: 38-05537 Rev. *S
Page 12 of 35
CY7C1354CV25
CY7C1356CV25
IEEE 1149.1 Serial Boundary Scan (JTAG)
The CY7C1354CV25/CY7C1356CV25 incorporates a serial
boundary scan test access port (TAP) in the BGA package only.
The TQFP package does not offer this functionality. This part
operates in accordance with IEEE Standard 1149.1-1900, but
doesn’t have the set of functions required for full 1149.1
compliance. These functions from the IEEE specification are
excluded because their inclusion places an added delay in the
critical speed path of the SRAM. Note the TAP controller
functions in a manner that does not conflict with the operation of
other devices using 1149.1 fully compliant TAPs. The TAP
operates using JEDEC-standard 2.5 V I/O logic levels.
The CY7C1354CV25/CY7C1356CV25 contains a TAP
controller, instruction register, boundary scan register, bypass
register, and ID register.
Disabling the JTAG Feature
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(VSS) to prevent clocking of the device. TDI and TMS are
internally pulled up and may be unconnected. They may
alternately be connected to VDD through a pull-up resistor. TDO
should be left unconnected. Upon power-up, the device will
come up in a reset state which will not interfere with the operation
of the device.
Test Access Port (TAP)
Test Clock (TCK)
The test clock is used only with the TAP controller. All inputs are
captured on the rising edge of TCK. All outputs are driven from
the falling edge of TCK.
Test Mode Select (TMS)
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. It is allowable to leave
this ball unconnected if the TAP is not used.
The ball is pulled up internally, resulting in a logic HIGH level.
Test Data-In (TDI)
The TDI ball is used to serially input information into the registers
and can be connected to the input of any of the registers. The
register between TDI and TDO is chosen by the instruction that
is loaded into the TAP instruction register. For information on
loading the instruction register, see TAP Controller State
Diagram on page 15. TDI is internally pulled up and can be
unconnected if the TAP is unused in an application. TDI is
connected to the most significant bit (MSB) of any register.
Test Data-Out (TDO)
The TDO output ball is used to serially clock data-out from the
registers. The output is active depending upon the current state
of the TAP state machine (see Instruction Codes on page 18).
The output changes on the falling edge of TCK. TDO is
connected to the least significant bit (LSB) of any register.
Document Number: 38-05537 Rev. *S
Performing a TAP Reset
A RESET is performed by forcing TMS HIGH (VDD) for five rising
edges of TCK. This RESET does not affect the operation of the
SRAM and may be performed while the SRAM is operating.
At power-up, the TAP is reset internally to ensure that TDO
comes up in a high Z state.
TAP Registers
Registers are connected between the TDI and TDO balls and
allow data to be scanned into and out of the SRAM test circuitry.
Only one register can be selected at a time through the
instruction register. Data is serially loaded into the TDI ball on the
rising edge of TCK. Data is output on the TDO ball on the falling
edge of TCK.
Instruction Register
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the TDI
and TDO balls as shown in the TAP Controller Block Diagram on
page 16. Upon power-up, the instruction register is loaded with
the IDCODE instruction.
It is also loaded with the IDCODE instruction if the controller is
placed in a reset state as described in the previous section.
When the TAP controller is in the Capture-IR state, the two least
significant bits are loaded with a binary “01” pattern to allow for
fault isolation of the board-level serial test data path.
Bypass Register
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between the
TDI and TDO balls. This allows data to be shifted through the
SRAM with minimal delay. The bypass register is set LOW (VSS)
when the BYPASS instruction is executed.
Boundary Scan Register
The boundary scan register is connected to all the input and
bidirectional balls on the SRAM.
The boundary scan register is loaded with the contents of the
RAM I/O ring when the TAP controller is in the Capture-DR state
and is then placed between the TDI and TDO balls when the
controller is moved to the Shift-DR state. The EXTEST,
SAMPLE/PRELOAD and SAMPLE Z instructions can be used to
capture the contents of the I/O ring.
The Boundary Scan Exit Order on page 19 and Boundary Scan
Exit Order on page 20 show the order in which the bits are
connected. Each bit corresponds to one of the bumps on the
SRAM package. The MSB of the register is connected to TDI,
and the LSB is connected to TDO.
Identification (ID) Register
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired into
the SRAM and can be shifted out when the TAP controller is in
the Shift-DR state. The ID register has a vendor code and other
information described in the Identification Register Definitions on
page 18.
Page 13 of 35
CY7C1354CV25
CY7C1356CV25
TAP Instruction Set
Overview
Eight different instructions are possible with the three bit
instruction register. All combinations are listed in the Instruction
Codes table. Three of these instructions are listed as
RESERVED and should not be used. The other five instructions
are described in detail below.
Instructions are loaded into the TAP controller during the Shift-IR
state when the instruction register is placed between TDI and
TDO. During this state, instructions are shifted through the
instruction register through the TDI and TDO balls. To execute
the instruction once it is shifted in, the TAP controller needs to be
moved into the Update-IR state.
IDCODE
The IDCODE instruction causes a vendor-specific, 32-bit code
to be loaded into the instruction register. It also places the
instruction register between the TDI and TDO balls and allows
the IDCODE to be shifted out of the device when the TAP
controller enters the Shift-DR state.
The IDCODE instruction is loaded into the instruction register
upon power-up or whenever the TAP controller is given a test
logic reset state.
SAMPLE Z
The SAMPLE Z instruction causes the boundary scan register to
be connected between the TDI and TDO pins when the TAP
controller is in a Shift-DR state. The SAMPLE Z command puts
the output bus into a high Z state until the next command is given
during the “Update IR” state.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the inputs and output pins is
captured in the boundary scan register.
The user must be aware that the TAP controller clock can only
operate at a frequency up to 20 MHz, while the SRAM clock
operates more than an order of magnitude faster. Because there
is a large difference in the clock frequencies, it is possible that
Document Number: 38-05537 Rev. *S
during the Capture-DR state, an input or output will undergo a
transition. The TAP may then try to capture a signal while in
transition (metastable state). This will not harm the device, but
there is no guarantee as to the value that will be captured.
Repeatable results may not be possible.
To guarantee that the boundary scan register will capture the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller’s capture set-up plus
hold times (tCS and tCH). The SRAM clock input might not be
captured correctly if there is no way in a design to stop (or slow)
the clock during a SAMPLE/PRELOAD instruction. If this is an
issue, it is still possible to capture all other signals and simply
ignore the value of the CK and CK# captured in the boundary
scan register.
Once the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the boundary
scan register between the TDI and TDO pins.
PRELOAD allows an initial data pattern to be placed at the
latched parallel outputs of the boundary scan register cells prior
to the selection of another boundary scan test operation.
The shifting of data for the SAMPLE and PRELOAD phases can
occur concurrently when required — that is, while data captured
is shifted out, the preloaded data can be shifted in.
BYPASS
When the BYPASS instruction is loaded in the instruction register
and the TAP is placed in a Shift-DR state, the bypass register is
placed between the TDI and TDO pins. The advantage of the
BYPASS instruction is that it shortens the boundary scan path
when multiple devices are connected together on a board.
EXTEST
The EXTEST instruction enables the preloaded data to be driven
out through the system output pins. This instruction also selects
the boundary scan register to be connected for serial access
between the TDI and TDO in the shift-DR controller state.
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
Page 14 of 35
CY7C1354CV25
CY7C1356CV25
TAP Controller State Diagram
The TAP Controller State Diagram follows. [13]
1
TEST-LOGIC
RESET
0
0
RUN-TEST/
IDLE
1
SELECT
DR-SCAN
1
SELECT
IR-SCAN
0
1
0
1
CAPTURE-DR
CAPTURE-IR
0
0
SHIFT-DR
0
SHIFT-IR
1
1
EXIT1-IR
0
1
0
PAUSE-DR
0
PAUSE-IR
1
0
1
EXIT2-DR
0
EXIT2-IR
1
1
UPDATE-DR
1
0
1
EXIT1-DR
0
1
0
UPDATE-IR
1
0
Note
13. The 0/1 next to each state represents the value of TMS at the rising edge of the TCK.
Document Number: 38-05537 Rev. *S
Page 15 of 35
CY7C1354CV25
CY7C1356CV25
TAP Controller Block Diagram
0
Bypass Register
2 1 0
TDI
Selection
Circuitry
Instruction Register
31 30 29 .
.
Selection
Circuitry
. 2 1 0
TDO
Identification Register
x .
.
.
.
. 2 1 0
Boundary Scan Register
TCK
TMS
TAP CONTROLLER
TAP Timing
1
2
Test Clock
(TCK)
3
tTH
tTMSS
tTMSH
tTDIS
tTDIH
t
TL
4
5
6
tCYC
Test Mode Select
(TMS)
Test Data-In
(TDI)
tTDOV
tTDOX
Test Data-Out
(TDO)
DON’T CARE
Document Number: 38-05537 Rev. *S
UNDEFINED
Page 16 of 35
CY7C1354CV25
CY7C1356CV25
TAP AC Switching Characteristics
Over the Operating Range
Parameter [14, 15]
Description
Min
Max
Unit
Clock
tTCYC
TCK clock cycle time
50
–
ns
tTF
TCK clock frequency
–
20
MHz
tTH
TCK clock HIGH time
20
–
ns
tTL
TCK clock LOW time
20
–
ns
tTDOV
TCK clock LOW to TDO valid
–
10
ns
tTDOX
TCK clock LOW to TDO invalid
0
–
ns
tTMSS
TMS set-up to TCK clock rise
5
–
ns
tTDIS
TDI set-up to TCK clock rise
5
–
ns
tCS
Capture set-up to TCK rise
5
–
ns
tTMSH
TMS hold after TCK clock rise
5
–
ns
tTDIH
TDI hold after clock rise
5
–
ns
tCH
Capture hold after clock rise
5
–
ns
Output Times
Set-up Times
Hold Times
2.5 V TAP AC Test Conditions
2.5 V TAP AC Output Load Equivalent
1.25V
Input pulse levels ...............................................VSS to 2.5 V
Input rise and fall time ....................................................1 ns
50Ω
Input timing reference levels ....................................... 1.25 V
Output reference levels .............................................. 1.25 V
TDO
Test load termination supply voltage .................. ........1.25 V
Z O= 50Ω
20pF
Notes
14. tCS and tCH refer to the set-up and hold time requirements of latching data from the boundary scan register.
15. Test conditions are specified using the load in TAP AC test Conditions. tR/tF = 1 ns.
Document Number: 38-05537 Rev. *S
Page 17 of 35
CY7C1354CV25
CY7C1356CV25
TAP DC Electrical Characteristics and Operating Conditions
(0 °C < TA < +70 °C; VDD = 2.5 V ± 0.125 V unless otherwise noted)
Parameter [16]
Description
Min
Max
Unit
IOH = –1.0 mA, VDDQ = 2.5 V
2.0
–
V
Output HIGH voltage
IOH = –100 µA, VDDQ = 2.5 V
2.1
–
V
Output LOW voltage
IOL = 8.0 mA, VDDQ = 2.5 V
–
0.4
V
VOL2
Output LOW voltage
IOL = 100 µA
VIH
Input HIGH voltage
VIL
Input LOW voltage
IX
Input Load current
VOH1
Output HIGH voltage
VOH2
VOL1
Test Conditions
VDDQ = 2.5 V
–
0.2
V
VDDQ = 2.5 V
1.7
VDD + 0.3
V
VDDQ = 2.5 V
–0.3
0.7
V
–5
5
µA
GND < VIN < VDDQ
Identification Register Definitions
CY7C1354CV25
CY7C1356CV25
Revision number (31:29)
Instruction Field
000
000
Cypress device ID (28:12)
01011001000100110
01011001000010110
Cypress JEDEC ID (11:1)
00000110100
00000110100
1
1
ID register presence (0)
Description
Reserved for version number.
Reserved for future use.
Allows unique identification of SRAM vendor.
Indicate the presence of an ID register.
Scan Register Sizes
Register Name
Bit Size (× 36)
Bit Size (× 18)
Instruction
3
3
Bypass
1
1
ID
32
32
Boundary scan order (119-ball BGA package)
69
69
Boundary scan order (165-ball FBGA package)
69
69
Instruction Codes
Instruction
Code
Description
EXTEST
000
Captures the input/output ring contents. Places the boundary scan register between the TDI
and TDO. Forces all SRAM outputs to high Z state.
IDCODE
001
Loads the ID register with the vendor ID code and places the register between TDI and TDO.
This operation does not affect SRAM operation.
SAMPLE Z
010
Captures the input/output contents. Places the boundary scan register between TDI and TDO.
Forces all SRAM output drivers to a high Z state.
RESERVED
011
Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD
100
Captures the input/output ring contents. Places the boundary scan register between TDI and
TDO. Does not affect the SRAM operation.
RESERVED
101
Do Not Use: This instruction is reserved for future use.
RESERVED
110
Do Not Use: This instruction is reserved for future use.
BYPASS
111
Places the bypass register between TDI and TDO. This operation does not affect SRAM
operation.
Note
16. All voltages referenced to VSS (GND).
Document Number: 38-05537 Rev. *S
Page 18 of 35
CY7C1354CV25
CY7C1356CV25
Boundary Scan Exit Order (continued)
Boundary Scan Exit Order
(256K × 36)
(256K × 36)
Bit #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
119-ball ID
K4
H4
M4
F4
B4
G4
C3
B3
D6
H7
G6
E6
D7
E7
F6
G7
H6
T7
K7
L6
N6
P7
N7
M6
L7
K6
P6
T4
A3
C5
B5
A5
C6
A6
P4
N4
R6
T5
T3
R2
R3
P2
P1
Document Number: 38-05537 Rev. *S
165-ball ID
B6
B7
A7
B8
A8
A9
B10
A10
C11
E10
F10
G10
D10
D11
E11
F11
G11
H11
J10
K10
L10
M10
J11
K11
L11
M11
N11
R11
R10
P10
R9
P9
R8
P8
R6
P6
R4
P4
R3
P3
R1
N1
L2
Bit #
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
119-ball ID
165-ball ID
L2
K2
K1
J2
N2
M2
N1
M1
M2
L1
L1
K1
K2
J1
Not Bonded (Preset to 1) Not Bonded (Preset to 1)
H1
G2
G2
F2
E2
E2
D1
D2
H2
G1
G1
F1
F2
E1
E1
D1
D2
C1
C2
B2
A2
A2
E4
A3
B2
B3
L3
B4
G3
A4
G5
A5
L5
B5
B6
A6
Page 19 of 35
CY7C1354CV25
CY7C1356CV25
Boundary Scan Exit Order (continued)
Boundary Scan Exit Order
(512K × 18)
(512K × 18)
Bit #
119-ball ID
165-ball ID
1
K4
B6
2
H4
B7
3
M4
A7
4
F4
B8
5
B4
A8
6
G4
A9
7
C3
B10
8
B3
A10
9
T2
A11
10
Not Bonded (Preset to 0) Not Bonded (Preset to 0)
11
Not Bonded (Preset to 0) Not Bonded (Preset to 0)
12
Not Bonded (Preset to 0) Not Bonded (Preset to 0)
13
D6
C11
14
E7
D11
15
F6
E11
16
G7
F11
17
H6
G11
18
T7
H11
19
K7
J10
20
L6
K10
21
N6
L10
22
P7
M10
23
Not Bonded (Preset to 0) Not Bonded (Preset to 0)
24
Not Bonded (Preset to 0) Not Bonded (Preset to 0)
25
Not Bonded (Preset to 0) Not Bonded (Preset to 0)
26
Not Bonded (Preset to 0) Not Bonded (Preset to 0)
27
Not Bonded (Preset to 0) Not Bonded (Preset to 0)
28
T6
R11
29
A3
R10
30
C5
P10
31
B5
R9
32
A5
P9
33
C6
R8
34
A6
P8
35
P4
R6
36
N4
P6
37
R6
R4
38
T5
P4
Document Number: 38-05537 Rev. *S
Bit #
119-ball ID
165-ball ID
39
T3
R3
40
R2
P3
41
R3
R1
42
Not Bonded (Preset to 0) Not Bonded (Preset to 0)
43
Not Bonded (Preset to 0) Not Bonded (Preset to 0)
44
Not Bonded (Preset to 0) Not Bonded (Preset to 0)
45
Not Bonded (Preset to 0) Not Bonded (Preset to 0)
46
P2
N1
47
N1
M1
48
M2
L1
49
L1
K1
K2
J1
50
51
Not Bonded (Preset to 1) Not Bonded (Preset to 1)
52
H1
G2
53
G2
F2
54
E2
E2
55
D1
D2
56
Not Bonded (Preset to 0) Not Bonded (Preset to 0)
57
Not Bonded (Preset to 0) Not Bonded (Preset to 0)
58
Not Bonded (Preset to 0) Not Bonded (Preset to 0)
59
Not Bonded (Preset to 0) Not Bonded (Preset to 0)
60
Not Bonded (Preset to 0) Not Bonded (Preset to 0)
61
C2
B2
62
A2
A2
63
E4
A3
B2
B3
64
65
Not Bonded (Preset to 0) Not Bonded (Preset to 0)
66
G3
Not Bonded (Preset to 0)
67
Not Bonded (Preset to 0)
A4
68
L5
B5
69
B6
A6
69
B6
A6
69
B6
A6
68
L5
B5
69
B6
A6
66
G3
Not Bonded (Preset to 0)
67
Not Bonded (Preset to 0)
A4
68
L5
B5
69
B6
A6
Page 20 of 35
CY7C1354CV25
CY7C1356CV25
Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the
device. User guidelines are not tested.
Storage temperature ................................ –65 °C to +150 °C
Ambient temperature
with power applied ................................... –55 °C to +125 °C
Supply voltage on VDD relative to GND .......–0.5 V to +3.6 V
Supply voltage on VDDQ relative to GND ...... –0.5 V to +VDD
DC to outputs in tri-state ...................–0.5 V to VDDQ + 0.5 V
DC input voltage ................................. –0.5 V to VDD + 0.5 V
Current into outputs (LOW) ........................................ 20 mA
Static discharge voltage
(per MIL-STD-883, method 3015) ......................... > 2001 V
Latch-up current ................................................... > 200 mA
Operating Range
Range
Ambient Temperature
VDD/VDDQ
0 °C to +70 °C
2.5 V ± 5%
Commercial
Industrial
–40 °C to +85 °C
Electrical Characteristics
Over the Operating Range
Parameter [17, 18]
Description
VDD
Power supply voltage
Test Conditions
Min
Max
Unit
2.375
2.625
V
2.375
VDD
V
2.0
–
V
–
0.4
V
V
VDDQ
I/O supply voltage
for 2.5 V I/O
VOH
Output HIGH voltage
for 2.5 V I/O, IOH = 1.0 mA
VOL
Output LOW voltage
for 2.5 V I/O, IOL= 1.0 mA
VIH
Input HIGH voltage
for 2.5 V I/O
1.7
VDD + 0.3 V
for 2.5 V I/O
[17]
VIL
Input LOW voltage
–0.3
0.7
V
IX
Input leakage current except ZZ GND VI VDDQ
and MODE
–5
5
A
Input current of MODE
Input = VSS
–30
–
A
Input = VDD
–
5
A
Input = VSS
–5
–
A
Input = VDD
–
30
A
Input current of ZZ
IOZ
Output leakage current
GND VI VDDQ, output disabled
IDD
VDD operating supply
VDD = Max, IOUT = 0 mA,
f = fMAX = 1/tCYC
ISB1
ISB2
Automatic CE power-down
current — TTL inputs
Automatic CE power-down
current — CMOS inputs
Max VDD, device deselected,
VIN VIH or VIN VIL,
f = fMAX = 1/tCYC
–5
5
A
4-ns cycle,
250 MHz
–
250
mA
5-ns cycle,
200 MHz
–
220
mA
6-ns cycle,
166 MHz
–
180
mA
4-ns cycle,
250 MHz
–
130
mA
5-ns cycle,
200 MHz
–
120
mA
6-ns cycle,
166 MHz
–
110
mA
–
40
mA
All speed
Max VDD, device deselected,
VIN 0.3 V or VIN > VDDQ 0.3 V, grades
f=0
Notes
17. Overshoot: VIH(AC) < VDD + 1.5 V (Pulse width less than tCYC/2), undershoot: VIL(AC) > –2 V (Pulse width less than tCYC/2).
18. TPower-up: Assumes a linear ramp from 0 V to VDD(min) within 200 ms. During this time VIH < VDD and VDDQ VDD.
Document Number: 38-05537 Rev. *S
Page 21 of 35
CY7C1354CV25
CY7C1356CV25
Electrical Characteristics (continued)
Over the Operating Range
Parameter [17, 18]
Description
Automatic CE power-down
current — CMOS inputs
ISB3
ISB4
Automatic CE power-down
current — TTL inputs
Test Conditions
Min
Max
Unit
Max VDD, device deselected,
4-ns cycle,
VIN 0.3 V or VIN > VDDQ 0.3 V, 250 MHz
f = fMAX = 1/tCYC
5-ns cycle,
200 MHz
–
120
mA
–
110
mA
6-ns cycle,
166 MHz
–
100
mA
All speed
grades
–
40
mA
Max VDD, device deselected,
VIN VIH or VIN VIL, f = 0
Capacitance
Parameter [19]
Description
Test Conditions
CIN
Input capacitance
CCLK
Clock input capacitance
CI/O
Input/output capacitance
100-pin TQFP 119-ball BGA 165-ball FBGA Unit
Max
Max
Max
TA = 25 °C, f = 1 MHz,
VDD = 2.5 V, VDDQ = 2.5 V
5
5
5
pF
5
5
5
pF
5
7
7
pF
Thermal Resistance
Parameter [19]
Description
JA
Thermal resistance
(junction to ambient)
JC
Thermal resistance
(junction to case)
Test Conditions
Test
conditions
follow
standard test methods and
procedures for measuring
thermal impedance, per
EIA/JESD51.
100-pin TQFP 119-ball BGA 165-ball FBGA Unit
Package
Package
Package
29.41
34.1
16.8
°C/W
6.13
14
3.0
°C/W
AC Test Loads and Waveforms
Figure 4. AC Test Loads and Waveforms
2.5 V I/O Test Load
R = 1667
2.5 V
OUTPUT
OUTPUT
RL = 50
Z0 = 50
VT = 1.25 V
(a)
ALL INPUT PULSES
VDDQ
GND
5 pF
INCLUDING
JIG AND
SCOPE
R = 1538
(b)
10%
90%
10%
90%
1 ns
1 ns
(c)
Note
19. Tested initially and after any design or process change that may affect these parameters.
Document Number: 38-05537 Rev. *S
Page 22 of 35
CY7C1354CV25
CY7C1356CV25
Switching Characteristics
Over the Operating Range
Parameter [20, 21]
tPower[22]
-250
Description
VCC(typical) to the first access read or
write
-200
-166
Min
Max
Min
Max
Min
Max
1
–
1
–
1
–
Unit
ms
Clock
tCYC
Clock cycle time
FMAX
Maximum operating frequency
4.0
–
5
–
6
–
ns
–
250
–
200
–
166
MHz
tCH
Clock HIGH
1.8
–
2.0
–
2.4
–
ns
tCL
Clock LOW
1.8
–
2.0
–
2.4
–
ns
Output Times
tCO
Data output valid after CLK rise
–
2.8
–
3.2
–
3.5
ns
tEOV
OE LOW to output valid
–
2.8
–
3.2
–
3.5
ns
tDOH
Data output hold after CLK rise
1.25
–
1.5
–
1.5
–
ns
1.25
2.8
1.5
3.2
1.5
3.5
ns
1.25
–
1.5
–
1.5
–
ns
–
2.8
–
3.2
–
3.5
ns
0
–
0
–
0
–
ns
[23, 24, 25]
tCHZ
Clock to high Z
tCLZ
Clock to low Z [23, 24, 25]
tEOHZ
tEOLZ
OE HIGH to output high Z
OE LOW to output low Z
[23, 24, 25]
[23, 24, 25]
Set-up Times
tAS
Address set-up before CLK rise
1.4
–
1.5
–
1.5
–
ns
tDS
Data input set-up before CLK rise
1.4
–
1.5
–
1.5
–
ns
tCENS
CEN set-up before CLK rise
1.4
–
1.5
–
1.5
–
ns
tWES
WE, BWx set-up before CLK rise
1.4
–
1.5
–
1.5
–
ns
tALS
ADV/LD set-up before CLK rise
1.4
–
1.5
–
1.5
–
ns
tCES
Chip select set-up
1.4
–
1.5
–
1.5
–
ns
tAH
Address hold after CLK rise
0.4
–
0.5
–
0.5
–
ns
tDH
Data input hold after CLK rise
0.4
–
0.5
–
0.5
–
ns
tCENH
CEN hold after CLK rise
0.4
–
0.5
–
0.5
–
ns
tWEH
WE, BWx hold after CLK rise
0.4
–
0.5
–
0.5
–
ns
tALH
ADV/LD hold after CLK rise
0.4
–
0.5
–
0.5
–
ns
tCEH
Chip select hold after CLK rise
0.4
–
0.5
–
0.5
–
ns
Hold Times
Notes
20. Timing reference level is when VDDQ = 2.5 V.
21. Test conditions shown in (a) of Figure 4 on page 22 unless otherwise noted.
22. This part has a voltage regulator internally; tpower is the time power needs to be supplied above VDD minimum initially, before a Read or Write operation can be initiated.
23. tCHZ, tCLZ, tEOLZ, and tEOHZ are specified with AC test conditions shown in (b) of Figure 4 on page 22. Transition is measured ± 200 mV from steady-state voltage.
24. At any given voltage and temperature, tEOHZ is less than tEOLZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same data
bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed to achieve
high Z prior to low Z under the same system conditions.
25. This parameter is sampled and not 100% tested.
Document Number: 38-05537 Rev. *S
Page 23 of 35
CY7C1354CV25
CY7C1356CV25
Switching Waveforms
Figure 5. Read/Write Timing [26, 27, 28]
1
2
3
t CYC
4
5
6
A3
A4
7
8
9
A5
A6
A7
10
CLK
tCENS
tCENH
tCL
tCH
CEN
tCES
tCEH
CE
ADV/LD
WE
BWX
A1
ADDRESS
A2
tCO
tAS
tDS
tAH
Data
In-Out (DQ)
tDH
D(A1)
tCLZ
D(A2)
D(A2+1)
tDOH
Q(A3)
tOEV
Q(A4)
tCHZ
Q(A4+1)
D(A5)
Q(A6)
tOEHZ
tDOH
tOELZ
OE
WRITE
D(A1)
WRITE
D(A2)
BURST
WRITE
D(A2+1)
READ
Q(A3)
READ
Q(A4)
DON’T CARE
BURST
READ
Q(A4+1)
WRITE
D(A5)
READ
Q(A6)
WRITE
D(A7)
DESELECT
UNDEFINED
Notes
26. For this waveform ZZ is tied LOW.
27. When CE is LOW, CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH, CE1 is HIGH or CE2 is LOW or CE3 is HIGH.
28. Order of the Burst sequence is determined by the status of the MODE (0 = Linear, 1 = Interleaved). Burst operations are optional.
Document Number: 38-05537 Rev. *S
Page 24 of 35
CY7C1354CV25
CY7C1356CV25
Switching Waveforms (continued)
Figure 6. NOP, STALL and DESELECT CYCLES [29, 30, 31]
1
2
A1
A2
3
4
5
A3
A4
6
7
8
9
10
CLK
CEN
CE
ADV/LD
WE
BWX
ADDRESS
A5
tCHZ
D(A1)
Data
Q(A2)
D(A4)
Q(A3)
Q(A5)
In-Out (DQ)
WRITE
D(A1)
READ
Q(A2)
STALL
READ
Q(A3)
WRITE
D(A4)
STALL
DON’T CARE
NOP
READ
Q(A5)
DESELECT
CONTINUE
DESELECT
UNDEFINED
Notes
29. For this waveform ZZ is tied LOW.
30. When CE is LOW, CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH, CE1 is HIGH or CE2 is LOW or CE3 is HIGH.
31. The IGNORE CLOCK EDGE or STALL cycle (Clock 3) illustrated CEN being used to create a pause. A write is not performed during this cycle.
Document Number: 38-05537 Rev. *S
Page 25 of 35
CY7C1354CV25
CY7C1356CV25
Switching Waveforms (continued)
Figure 7. ZZ Mode Timing [32, 33]
CLK
t ZZ
ZZ
I
t ZZREC
t ZZI
SUPPLY
I DDZZ
t RZZI
ALL INPUTS
(except ZZ)
Outputs (Q)
DESELECT or READ Only
High-Z
DON’T CARE
Notes
32. Device must be deselected when entering ZZ mode. See cycle description table for all possible signal conditions to deselect the device.
33. I/Os are in high Z when exiting ZZ sleep mode.
Document Number: 38-05537 Rev. *S
Page 26 of 35
CY7C1354CV25
CY7C1356CV25
Ordering Information
Cypress offers other versions of this type of product in many different configurations and features. The below table contains only the
list of parts that are currently available.For a complete listing of all options, visit the Cypress website at www.cypress.com and refer
to the product summary page at http://www.cypress.com/products or contact your local sales representative.
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives and distributors. To find the office
closest to you, visit us at http://www.cypress.com/go/datasheet/offices.
Speed
(MHz)
Ordering Code
166
200
Package
Diagram
Part and Package Type
CY7C1354CV25-166AXC
51-85050 100-pin TQFP (14 × 20 × 1.4 mm) Pb-free
CY7C1354CV25-166BZC
51-85180 165-ball FBGA (13 × 15 × 1.4 mm)
CY7C1354CV25-200AXC
51-85050 100-pin TQFP (14 × 20 × 1.4 mm) Pb-free
Operating
Range
Commercial
Commercial
Ordering Code Definitions
CY
7
C
135X
C
V25 - XXX XX X
C
Temperature Range: C = Commercial
Pb-free
Package Type: XX = A or BZ
A = 100-pin TQFP
BZ = 165-ball FBGA
Speed Grade: XXX = 166 MHz or 200 MHz
V25 = 2.5 V
Process Technology 90 nm
135X = 1354 or 1356
1354 = PL, 256Kb × 36 (9Mb)
1356 = PL, 512Kb × 18 (9Mb)
Technology Code: C = CMOS
Marketing Code: 7 = SRAM
Company ID: CY = Cypress
Document Number: 38-05537 Rev. *S
Page 27 of 35
CY7C1354CV25
CY7C1356CV25
Package Diagrams
Figure 8. 100-pin TQFP (14 × 20 × 1.4 mm) Package Outline, 51-85050
ș2
ș1
ș
SYMBOL
DIMENSIONS
MIN. NOM. MAX.
A
1.60
0.15
NOTE:
1. ALL DIMENSIONS ARE IN MILLIMETERS.
2. BODY LENGTH DIMENSION DOES NOT
A1
0.05
A2
1.35 1.40 1.45
D
15.80 16.00 16.20
MOLD PROTRUSION/END FLASH SHALL
D1
13.90 14.00 14.10
E
21.80 22.00 22.20
NOT EXCEED 0.0098 in (0.25 mm) PER SIDE.
BODY LENGTH DIMENSIONS ARE MAX PLASTIC
E1
19.90 20.00 20.10
R1
0.08
0.20
R2
0.08
0.20
ș
0°
7°
ș1
0°
ș2
11°
13°
12°
b
0.22 0.30 0.38
L
0.45 0.60 0.75
L2
L3
e
BODY SIZE INCLUDING MOLD MISMATCH.
3. JEDEC SPECIFICATION NO. REF: MS-026.
0.20
c
L1
INCLUDE MOLD PROTRUSION/END FLASH.
1.00 REF
0.25 BSC
0.20
0.65 TYP
51-85050 *G
Document Number: 38-05537 Rev. *S
Page 28 of 35
CY7C1354CV25
CY7C1356CV25
Package Diagrams (continued)
Figure 9. 119-ball PBGA (14 × 22 × 2.4 mm) Package Outline, 51-85115
51-85115 *D
Document Number: 38-05537 Rev. *S
Page 29 of 35
CY7C1354CV25
CY7C1356CV25
Package Diagrams (continued)
Figure 10. 165-ball FBGA (13 × 15 × 1.4 mm (0.5 Ball Diameter)) Package Outline, 51-85180
51-85180 *G
Document Number: 38-05537 Rev. *S
Page 30 of 35
CY7C1354CV25
CY7C1356CV25
Acronyms
Acronym
Document Conventions
Description
Units of Measure
BGA
Ball Grid Array
CE
Chip Enable
°C
degree Celsius
CEN
Clock Enable
MHz
megahertz
CMOS
Complementary Metal Oxide Semiconductor
µA
microampere
EIA
Electronic Industries Alliance
mA
milliampere
FBGA
Fine-Pitch Ball Grid Array
mm
millimeter
I/O
Input/Output
ms
millisecond
JEDEC
Joint Electron Devices Engineering Council
mV
millivolt
JTAG
Joint Test Action Group
ns
nanosecond
LSB
Least Significant Bit
MSB
Most Significant Bit
NoBL
No Bus Latency
OE
Output Enable
SRAM
Static Random Access Memory
TAP
Test Access Port
TCK
Test Clock
TDI
Test Data-In
TDO
Test Data-Out
TMS
Test mode select
TQFP
Thin Quad Flat Pack
TTL
Transistor-Transistor Logic
WE
Write Enable
Document Number: 38-05537 Rev. *S
Symbol
Unit of Measure
ohm
%
percent
pF
picofarad
V
volt
W
watt
Page 31 of 35
CY7C1354CV25
CY7C1356CV25
Document History Page
Document Title: CY7C1354CV25/CY7C1356CV25, 9-Mbit (256K × 36/512K × 18) Pipelined SRAM with NoBL™ Architecture
Document Number: 38-05537
Rev.
ECN No.
Orig. of
Change
Submission
Date
**
242032
RKF
07/13/2004
New data sheet.
*A
278969
RKF
10/18/2004
Updated Boundary Scan Exit Order (To match the B Rev of these devices).
Updated Boundary Scan Exit Order (To match the B Rev of these devices).
*B
284929
RKF / VBL
11/01/2004
Updated Functional Overview:
Updated ZZ Mode Electrical Characteristics:
Changed maximum value of IDDZZ parameter from 35 mA to 50 mA.
Added Electrical Characteristics.
Updated Ordering Information:
Updated part numbers.
*C
323636
PCI
02/22/2005
Removed “225 MHz” Frequency Range related information in all instances
across the document.
Added “250 MHz” Frequency Range related information in all instances across
the document.
Updated Pin Definitions:
Modified address expansion as per JEDEC Standard in all instances across
the document.
Updated Thermal Resistance:
Changed value of JA parameter corresponding to 100-pin TQFP Package
from 25 °C/W to 29.41 °C/W.
Changed value of JC parameter corresponding to 100-pin TQFP Package
from 9 °C/W to 6.13 °C/W.
Changed value of JA parameter corresponding to 119-ball BGA Package from
25 °C/W to 34.1 °C/W.
Changed value of JC parameter corresponding to 119-ball BGA Package from
6 °C/W to 14.0 °C/W.
Changed value of JA parameter corresponding to 165-ball FBGA Package
from 27 °C/W to 16.8 °C/W.
Changed value of JC parameter corresponding to 165-ball FBGA Package
from 6 °C/W to 3.0 °C/W.
Updated Switching Characteristics:
Changed minimum value of tCYC parameter from 4.4 ns to 4.0 ns corresponding
to 250 MHz frequency.
Updated Ordering Information:
No change in part numbers.
Removed comment “Lead-free BGX package will be available in 2005.” below
the table.
*D
332879
PCI
03/13/2005
Updated Selection Guide:
Unshaded 200 MHz and 166 MHz speed bins related information.
Updated Pin Definitions:
Added Address Expansion pins.
Updated IEEE 1149.1 Serial Boundary Scan (JTAG):
Updated TAP Instruction Set:
Removed “EXTEST OUTPUT BUS TRI-STATE”.
Updated Electrical Characteristics:
Unshaded 200 MHz and 166 MHz speed bins related information.
Updated details in “Test Conditions” column corresponding to VOL and VOH
parameters.
Updated Switching Characteristics:
Unshaded 200 MHz and 166 MHz speed bins related information.
Updated Ordering Information:
Updated part numbers.
Document Number: 38-05537 Rev. *S
Description of Change
Page 32 of 35
CY7C1354CV25
CY7C1356CV25
Document History Page (continued)
Document Title: CY7C1354CV25/CY7C1356CV25, 9-Mbit (256K × 36/512K × 18) Pipelined SRAM with NoBL™ Architecture
Document Number: 38-05537
Rev.
ECN No.
Orig. of
Change
Submission
Date
*E
357258
PCI
05/05/2005
Changed status from Preliminary to Final.
Updated Selection Guide:
Unshaded 250 MHz speed bin related information.
Updated Electrical Characteristics:
Changed maximum value of ISB2 parameter from 35 mA to 40 mA.
Unshaded 250 MHz speed bin related information.
Updated Switching Characteristics:
Unshaded 250 MHz speed bin related information.
Updated Ordering Information:
Updated part numbers.
*F
377095
PCI
06/10/2005
Updated Electrical Characteristics:
Updated Note 18 (Replaced “VDDQ < VDD” with “VDDQ VDD”).
*G
408298
RXU
11/16/2005
Changed address of Cypress Semiconductor Corporation in page 1 from “3901
North First Street” to “198 Champion Court”.
Replaced “three-state” with “tri-state” in all instances across the document.
Updated Electrical Characteristics:
Replaced “Input Load” with “Input Leakage Current except ZZ and MODE” in
“Description” column corresponding to IX parameter.
Updated Ordering Information:
Updated part numbers.
Removed “Package Name” column.
Added “Package Diagram” column.
Updated Package Diagrams:
spec 51-85180 – Changed revision from ** to *A.
Updated to new template.
*H
501793
VKN
09/13/2006
Updated Switching Characteristics:
Changed minimum value of tTH, and tTL parameters from 25 ns to 20 ns.
Changed maximum value of tTDOV parameter from 5 ns to 10 ns.
Updated Maximum Ratings:
Added “Supply Voltage on VDDQ Relative to GND” and its rating.
Updated Ordering Information:
Updated part numbers.
Updated Package Diagrams:
spec 51-85050 – Changed revision from *A to *B.
*I
2898958
NJY
03/25/2010
Updated Ordering Information:
Updated part numbers.
Updated Package Diagrams:
spec 51-85050 – Changed revision from *B to *C.
spec 51-85115 – Changed revision from *B to *C.
spec 51-85180 – Changed revision from *A to *C.
*J
3033272
NJY
09/19/2010
Updated Ordering Information:
No change in part numbers.
Added Ordering Code Definitions.
Added Acronyms and Units of Measure.
Minor edits.
Updated to new template.
Completing Sunset Review.
*K
3052726
NJY
10/08/2010
Updated Ordering Information:
Updated part numbers.
*L
3385314
PRIT
09/29/2011
Updated Package Diagrams:
spec 51-85050 – Changed revision from *C to *D.
Completing Sunset Review.
Document Number: 38-05537 Rev. *S
Description of Change
Page 33 of 35
CY7C1354CV25
CY7C1356CV25
Document History Page (continued)
Document Title: CY7C1354CV25/CY7C1356CV25, 9-Mbit (256K × 36/512K × 18) Pipelined SRAM with NoBL™ Architecture
Document Number: 38-05537
Rev.
ECN No.
Orig. of
Change
Submission
Date
*M
3754566
PRIT
09/25/2012
Updated Package Diagrams:
spec 51-85115 – Changed revision from *C to *D.
spec 51-85180 – Changed revision from *C to *F.
Completing Sunset Review.
*N
4537527
PRIT
10/14/2014
Updated Package Diagrams:
spec 51-85050 – Changed revision from *D to *E.
Updated to new template.
Completing Sunset Review.
*O
4571917
PRIT
11/18/2014
Updated Functional Description:
Added “For a complete list of related documentation, click here.” at the end.
*P
4974141
PRIT
10/19/2015
Updated Package Diagrams:
spec 51-85180 – Changed revision from *F to *G.
Updated to new template.
Completing Sunset Review.
*Q
5509821
PRIT
11/04/2016
Updated Package Diagrams:
spec 51-85050 – Changed revision from *E to *F.
Updated to new template.
Completing Sunset Review.
*R
6021076
RMES
01/09/2018
Updated Package Diagrams:
spec 51-85050 – Changed revision from *F to *G.
Updated to new template.
Completing Sunset Review.
*S
6534109
RMES
04/05/2019
Updated Ordering Information:
Updated part numbers.
Updated to new template.
Document Number: 38-05537 Rev. *S
Description of Change
Page 34 of 35
CY7C1354CV25
CY7C1356CV25
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
PSoC® Solutions
Products
Arm® Cortex® Microcontrollers
Automotive
cypress.com/arm
cypress.com/automotive
Clocks & Buffers
Interface
Internet of Things
Memory
cypress.com/clocks
cypress.com/interface
cypress.com/iot
cypress.com/memory
Microcontrollers
cypress.com/mcu
PSoC
cypress.com/psoc
Power Management ICs
Touch Sensing
USB Controllers
Wireless Connectivity
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP | PSoC 6 MCU
Cypress Developer Community
Community | Projects | Video | Blogs | Training | Components
Technical Support
cypress.com/support
cypress.com/pmic
cypress.com/touch
cypress.com/usb
cypress.com/wireless
© Cypress Semiconductor Corporation, 2004–2019. This document is the property of Cypress Semiconductor Corporation and its subsidiaries (“Cypress”). This document, including any software or
firmware included or referenced in this document (“Software”), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress
reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property
rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants
you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce
the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or
indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress’s patents that are infringed by the Software (as provided by
Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the
Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No computing
device can be absolutely secure. Therefore, despite security measures implemented in Cypress hardware or software products, Cypress shall have no liability arising out of any security breach, such
as unauthorized access to or use of a Cypress product. CYPRESS DOES NOT REPRESENT, WARRANT, OR GUARANTEE THAT CYPRESS PRODUCTS, OR SYSTEMS CREATED USING
CYPRESS PRODUCTS, WILL BE FREE FROM CORRUPTION, ATTACK, VIRUSES, INTERFERENCE, HACKING, DATA LOSS OR THEFT, OR OTHER SECURITY INTRUSION (collectively, “Security
Breach”). Cypress disclaims any liability relating to any Security Breach, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from any Security Breach. In
addition, the products described in these materials may contain design defects or errors known as errata which may cause the product to deviate from published specifications. To the extent permitted
by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or
circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the
responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. “High-Risk Device”
means any device or system whose failure could cause personal injury, death, or property damage. Examples of High-Risk Devices are weapons, nuclear installations, surgical implants, and other
medical devices. “Critical Component” means any component of a High-Risk Device whose failure to perform can be reasonably expected to cause, directly or indirectly, the failure of the High-Risk
Device, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from any use of
a Cypress product as a Critical Component in a High-Risk Device. You shall indemnify and hold Cypress, its directors, officers, employees, agents, affiliates, distributors, and assigns harmless from
and against all claims, costs, damages, and expenses, arising out of any claim, including claims for product liability, personal injury or death, or property damage arising from any use of a Cypress
product as a Critical Component in a High-Risk Device. Cypress products are not intended or authorized for use as a Critical Component in any High-Risk Device except to the limited extent that (i)
Cypress’s published data sheet for the product explicitly states Cypress has qualified the product for use in a specific High-Risk Device, or (ii) Cypress has given you advance written authorization to
use the product as a Critical Component in the specific High-Risk Device and you have signed a separate indemnification agreement.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in
the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
Document Number: 38-05537 Rev. *S
Revised April 5, 2019
NoBL and No Bus Latency are trademarks of Cypress Semiconductor Corporation. ZBT is a trademark of Integrated Device Technology, Inc.
Page 35 of 35