CY7C1361B-100AJC

CY7C1361B CY7C1363B 9-Mbit (256K x 36/512K x 18) Flow-Through SRAM Functional Description[1] Features • • • • • Supports 133-MHz bus operations 256K X 36/512K X 18 common I/O 3.3V –5% and +10% core power supply (VDD) 2.5V or 3.3V I/O supply (VDDQ) Fast clock-to-output times — 6.5 ns (133-MHz version) — 7.5 ns (117-MHz version) • • • • • • — 8.5 ns (100-MHz version) Provide high-performance 2-1-1-1 access rate User-selectable burst counter supporting Intel Pentium interleaved or linear burst sequences Separate processor and controller address strobes Synchronous self-timed write Asynchronous output enable Offered in JEDEC-standard 100-pin TQFP, 119-ball BGA and 165-ball fBGA packages — Both 2 and 3 Chip Enable Options for TQFP • JTAG boundary scan for BGA and fBGA packages • “ZZ” Sleep Mode option The CY7C1361B/CY7C1363B is a 3.3V, 256K x 36 and 512K x 18 Synchronous Flow through SRAMs, respectively designed to interface with high-speed microprocessors with minimum glue logic. Maximum access delay from clock rise is 6.5 ns (133-MHz version). A 2-bit on-chip counter captures the first address in a burst and increments the address automatically for the rest of the burst access. All synchronous inputs are gated by registers controlled by a positive-edge-triggered Clock Input (CLK). The synchronous inputs include all addresses, all data inputs, address-pipelining Chip Enable (CE1), depth-expansion Chip Enables (CE2 and CE3[2]), Burst Control inputs (ADSC, ADSP, and ADV), Write Enables (BWx, and BWE), and Global Write (GW). Asynchronous inputs include the Output Enable (OE) and the ZZ pin. The CY7C1361B/CY7C1363B allows either interleaved or linear burst sequences, selected by the MODE input pin. A HIGH selects an interleaved burst sequence, while a LOW selects a linear burst sequence. Burst accesses can be initiated with the Processor Address Strobe (ADSP) or the cache Controller Address Strobe (ADSC) inputs. Address advancement is controlled by the Address Advancement (ADV) input. Addresses and chip enables are registered at rising edge of clock when either Address Strobe Processor (ADSP) or Address Strobe Controller (ADSC) are active. Subsequent burst addresses can be internally generated as controlled by the Advance pin (ADV). The CY7C1361B/CY7C1363B operates from a +3.3V core power supply while all outputs may operate with either a +2.5 or +3.3V supply. All inputs and outputs are JEDEC-standard JESD8-5-compatible. Selection Guide 133 MHz 117 MHz 100 MHz Unit Maximum Access Time 6.5 7.5 8.5 ns Maximum Operating Current 250 220 180 mA Maximum CMOS Standby Current 30 30 30 mA Notes: 1. For best–practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com. 2. CE3 is for A version of TQFP (3 Chip Enable Option) and 165 fBGA package only. 119 BGA is offered only in 2 Chip Enable. Cypress Semiconductor Corporation Document #: 38-05302 Rev. *B • 3901 North First Street • San Jose, CA 95134 • 408-943-2600 Revised April 20, 2004 CY7C1361B CY7C1363B 1 Logic Block Diagram – CY7C1361B (256K x 36) ADDRESS REGISTER A0, A1, A A[1:0] MODE BURST Q1 COUNTER AND LOGIC Q0 CLR ADV CLK ADSC ADSP DQD, DQPD DQD, DQPD BWD BYTE BYTE WRITE REGISTER WRITE REGISTER DQC, DQPC DQC, DQPC BWC BYTE BYTE WRITE REGISTER WRITE REGISTER DQB, DQPB BWB DQB, DQPB BYTE BYTE WRITE REGISTER MEMORY ARRAY SENSE AMPS OUTPUT BUFFERS DQs DQPA DQPB DQPC DQPD WRITE REGISTER DQA, DQPA BWA BWE DQA, DQPA BYTE BYTE WRITE REGISTER WRITE REGISTER INPUT REGISTERS GW ENABLE REGISTER CE1 CE2 CE3 OE SLEEP CONTROL ZZ 2 Logic Block Diagram – CY7C1363B (512K x 18) ADDRESS REGISTER A0,A1,A A[1:0] MODE BURST Q1 COUNTER AND LOGIC CLR Q0 ADV CLK ADSC ADSP BWB BWA DQB,DQPB WRITE REGISTER DQA,DQPA WRITE REGISTER DQB,DQPB WRITE DRIVER MEMORY ARRAY SENSE AMPS OUTPUT BUFFERS DQs DQPA DQPB DQA,DQPA WRITE DRIVER BWE GW CE1 CE2 CE3 ENABLE REGISTER INPUT REGISTERS OE ZZ Document #: 38-05302 Rev. *B SLEEP CONTROL Page 2 of 34 CY7C1361B CY7C1363B Pin Configurations NC NC NC CY7C1363B (512K x 18) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 VDDQ VSSQ NC NC DQB DQB VSSQ VDDQ DQB DQB VSS/DNU VDD NC VSS DQB DQB VDDQ VSSQ DQB DQB DQPB NC VSSQ VDDQ NC NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 MODE A A A A A1 A0 NC NC VSS VDD NC A A A A A A A A DQPB DQB DQB VDDQ VSSQ DQB DQB DQB DQB VSSQ VDDQ DQB DQB VSS NC VDD ZZ DQA DQA VDDQ VSSQ DQA DQA DQA DQA VSSQ VDDQ DQA DQA DQPA 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 CY7C1361B (256K x 36) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 MODE A A A A A1 A0 NC NC VSS VDD NC A A A A A A A A DQPC DQC DQC VDDQ VSSQ DQC DQC DQC DQC VSSQ VDDQ DQC DQC VSS/DNU VDD NC VSS DQD DQD VDDQ VSSQ DQD DQD DQD DQD VSSQ VDDQ DQD DQD DQPD A A CE1 CE2 NC NC BWB BWA CE3 VDD VSS CLK GW BWE OE ADSC ADSP ADV A A A A CE1 CE2 BWD BWC BWB BWA CE3 VDD VSS CLK GW BWE OE ADSC ADSP ADV A A 100-pin TQFP Pinout (3 Chip Enables) (A version) Document #: 38-05302 Rev. *B A NC NC VDDQ VSSQ NC DQPA DQA DQA VSSQ VDDQ DQA DQA VSS NC VDD ZZ DQA DQA VDDQ VSSQ DQA DQA NC NC VSSQ VDDQ NC NC NC Page 3 of 34 CY7C1361B CY7C1363B Pin Configurations (continued) NC NC VSS VDD NC NC A A A A A A A MODE A A A A A1 A0 Document #: 38-05302 Rev. *B NC NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 VDDQ VSSQ NC NC DQB DQB VSSQ VDDQ DQB DQB VSS/DNU VDD NC VSS DQB DQB VDDQ VSSQ DQB DQB DQPB NC VSSQ VDDQ NC NC NC CY7C1363B (512K x 18) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 A NC NC VDDQ VSSQ NC DQPA DQA DQA VSSQ VDDQ DQA DQA VSS NC VDD ZZ DQA DQA VDDQ VSSQ DQA DQA NC NC VSSQ VDDQ NC NC NC 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 DQPB DQB DQB VDDQ VSSQ DQB DQB DQB DQB VSSQ VDDQ DQB DQB VSS NC VDD ZZ DQA DQA VDDQ VSSQ DQA DQA DQA DQA VSSQ VDDQ DQA DQA DQPA A A A A A1 A0 NC NC VSS VDD NC NC A A A A A A A CY7C1361B (256K x 36) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 MODE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 DQPC DQC DQC VDDQ VSSQ DQC DQC DQC DQC VSSQ VDDQ DQC DQC VSS/DNU VDD NC VSS DQD DQD VDDQ VSSQ DQD DQD DQD DQD VSSQ VDDQ DQD DQD DQPD 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 A A CE1 CE2 NC NC BWB BWA A VDD VSS CLK GW BWE OE ADSC ADSP ADV A A A A CE1 CE2 BWD BWC BWB BWA A VDD VSS CLK GW BWE OE ADSC ADSP ADV A A 100-pin TQFP (2 Chip Enables) (AJ Version) Page 4 of 34 CY7C1361B CY7C1363B Pin Configurations (continued) 119-ball BGA (2 Chip Enables with JTAG) 1 CY7C1361B (256K x 36) 3 4 5 A A ADSP A VDDQ 2 A B C NC NC CE2 A A A ADSC VDD A A A A NC NC D E DQC DQC DQPC DQC VSS VSS NC CE1 VSS VSS DQPB DQB DQB DQB F VDDQ DQC VSS OE VSS DQB VDDQ G H J K DQC DQC VDDQ DQD DQC DQC VDD DQD BWC VSS NC VSS ADV BWB VSS NC VSS DQB DQB VDD DQA DQB DQB VDDQ DQA BWA VSS DQA DQA DQA VDDQ VSS DQA DQA GW VDD CLK NC 6 A 7 VDDQ L DQD DQD M VDDQ DQD BWD VSS N DQD DQD VSS BWE A1 P DQD DQPD VSS A0 VSS DQPA DQA R NC A MODE VDD NC A NC T U NC VDDQ NC TMS A TDI A TCK A TDO NC NC ZZ VDDQ CY7C1363B (512K x 18) 1 2 3 4 5 6 7 A VDDQ A A ADSP A A VDDQ B NC CE2 A A A A A A NC NC ADSC VDD A C D DQB NC VSS NC VSS DQPA NC E NC DQB VSS CE1 VSS NC DQA OE ADV VSS DQA VDDQ VSS VSS NC DQA VDD DQA NC VDDQ NC DQA BWA VSS DQA NC NC VDDQ NC F VDDQ NC VSS G H J NC DQB VDDQ DQB NC VDD BWB VSS NC K NC DQB VSS L M DQB VDDQ NC DQB VSS VSS N DQB NC VSS BWE A1 VSS DQA NC P NC DQPB VSS A0 VSS NC DQA R T U NC NC VDDQ A A TMS MODE A TDI VDD NC TCK NC A TDO A A NC NC ZZ VDDQ Document #: 38-05302 Rev. *B GW VDD CLK NC NC VSS Page 5 of 34 CY7C1361B CY7C1363B Pin Configurations (continued) 165-ball fBGA (3 Chip Enable) CY7C1361B (256K x 36) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G H J K L M N P NC / 288M A CE1 BWC BWB CE3 BWE ADSC ADV A NC R NC A CE2 BWD BWA CLK GW OE ADSP A NC / 144M DQPC DQC NC DQC VDDQ VSS VSS VSS VSS VSS VSS VSS VDD VDDQ VDDQ VSS VDD VDDQ NC DQB DQPB DQB DQC DQC VDDQ VDD VSS VSS VSS VDD VDDQ DQB DQB DQC DQC VDDQ VDD VSS VSS VSS VDD DQB DQB DQC NC DQD DQC VSS DQD VDDQ NC VDDQ VDD VDD VDD VSS VSS VSS VSS VSS VSS VSS VSS VSS VDD VDD VDD VDDQ VDDQ NC VDDQ DQB NC DQA DQB ZZ DQA DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA DQD DQPD DQD NC VDDQ VDDQ VDD VSS VSS NC VSS VDD VSS VDDQ VDDQ DQA NC DQA DQPA NC NC / 72M A A TDI NC / 18M A1 VSS NC TDO A A A A MODE NC / 36M A A TMS A0 TCK A A A A CY7C1363B (512K x 18) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G H J K L M N P NC / 288M A CE1 BWB NC CE3 BWE ADSC ADV A A NC A CE2 NC BWA CLK GW OE ADSP A NC NC NC DQB VDDQ VSS VDD VSS VSS VSS VSS VSS VSS VSS VDD VDDQ VDDQ VDDQ NC NC NC DQB VDDQ VDD VSS VSS VSS VDD VDDQ NC DQA NC DQB VDDQ VDD VSS VSS VSS VDD VDDQ NC DQA NC VSS DQB DQB VSS NC VDDQ NC VDDQ VDD VDD VDD VSS VSS VSS VSS VSS VSS VSS VSS VSS VDD VDD VDD VDDQ NC VDDQ NC NC DQA DQA ZZ NC DQB NC VDDQ VDD VSS VSS VSS VDD VDDQ DQA NC DQB NC VDDQ VDD VSS VSS VSS VDD VDDQ DQA NC DQB DQPB NC NC VDDQ VDDQ VDD VSS VSS NC VSS NC / 18M VSS NC VDD VSS VDDQ VDDQ DQA NC NC NC NC NC / 72M A A TDI A1 TDO A A A A R MODE NC / 36M A A TMS A0 TCK A A A A Document #: 38-05302 Rev. *B NC / 144M DQPA DQA Page 6 of 34 CY7C1361B CY7C1363B CY7C1361B–Pin Definitions TQFP (3-Chip Enable) TQFP (2-Chip Enable) BGA (2-Chip Enable) A0, A1, A 37,36,32,33, 34,35,43,44, 45,46,47,48, 49,50,81,82, 99,100 37,36,32,33, 34,35,44,45, 46,47,48,49, 50,81,82,92, 99,100 P4,N4,A2, C2,R2,A3, B3,C3,T3, T4,A5,B5, C5,T5,A6, B6,C6,R6 BWA,BWB 93,94,95,96 93,94,95,96 L5,G5,G3, L3 Name BWC,BWD fBGA (3-Chip Enable) I/O Description InputAddress Inputs used to select one of the R6,P6,A2, A10,B2,B10, Synchronous 256K address locations. Sampled at the rising edge of the CLK if ADSP or ADSC is P3,P4,P8, P9,P10,P11, active LOW, and CE1, CE2, and CE3[2] are R3,R4,R8, sampled active. A[1:0] feed the 2-bit counter. R9,R10,R11 B5,A5,A4, B4 InputByte Write Select Inputs, active LOW. QualSynchronous ified with BWE to conduct byte writes to the SRAM. Sampled on the rising edge of CLK. InputGlobal Write Enable Input, active LOW. Synchronous When asserted LOW on the rising edge of CLK, a global write is conducted (ALL bytes are written, regardless of the values on BW[A:D]and BWE). GW 88 88 H4 B7 CLK 89 89 K4 B6 98 98 E4 A3 CE2 97 97 B2 B3 CE3[2] 92 – – A6 InputChip Enable 3 Input, active LOW. Sampled Synchronous on the rising edge of CLK. Used in conjunction with CE1 and CE2 to select/ deselect the device. OE 86 86 F4 B8 InputOutput Enable, asynchronous input, Asynchronous active LOW. Controls the direction of the I/O pins. When LOW, the I/O pins behave as outputs. When deasserted HIGH, I/O pins are three-stated, and act as input data pins. OE is masked during the first clock of a read cycle when emerging from a deselected state. ADV 83 83 G4 A9 InputAdvance Input signal, sampled on the Synchronous rising edge of CLK. When asserted, it automatically increments the address in a burst cycle. ADSP 84 84 A4 B9 InputAddress Strobe from Processor, sampled Synchronous on the rising edge of CLK, active LOW. When asserted LOW, addresses presented to the device are captured in the address registers. A[1:0] are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. ASDP is ignored when CE1 is deasserted HIGH. CE1 Document #: 38-05302 Rev. *B InputClock Clock Input. Used to capture all synchronous inputs to the device. Also used to increment the burst counter when ADV is asserted LOW, during a burst operation. InputChip Enable 1 Input, active LOW. Sampled Synchronous on the rising edge of CLK. Used in conjunction with CE2 and CE3[2] to select/deselect the device. ADSP is ignored if CE1 is HIGH. InputChip Enable 2 Input, active HIGH. Synchronous Sampled on the rising edge of CLK. Used in conjunction with CE1 and CE3[2] to select/deselect the device. Page 7 of 34 CY7C1361B CY7C1363B CY7C1361B–Pin Definitions (continued) Name ADSC BWE ZZ DQs DQP[A:D] MODE TQFP (3-Chip Enable) TQFP (2-Chip Enable) BGA (2-Chip Enable) fBGA (3-Chip Enable) 85 85 B4 A8 InputAddress Strobe from Controller, sampled Synchronous on the rising edge of CLK, active LOW. When asserted LOW, addresses presented to the device are captured in the address registers. A[1:0] are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. 87 87 M4 A7 InputByte Write Enable Input, active LOW. Synchronous Sampled on the rising edge of CLK. This signal must be asserted LOW to conduct a byte write. 64 64 T7 H11 InputZZ “sleep” Input, active HIGH. When Asynchronous asserted HIGH places the device in a non-time-critical “sleep” condition with data integrity preserved. For normal operation, this pin has to be LOW or left floating. ZZ pin has an internal pull-down. 52,53,56,57, 58,59,62,63, 68,69,72,73, 74,75,78,79, 2,3,6,7,8,9, 12,13,18,19, 22,23,24,25, 28,29 52,53,56,57, 58,59,62,63, 68,69,72,73, 74,75,78,79, 2,3,6,7,8,9, 12,13,18,19, 22,23,24,25, 28,29 51,80,1,30 K6,L6,M6, M11,L11, K11,J11, N6,K7,L7, N7,P7,E6, J10,K10, F6,G6,H6, L10,M10, D7,E7,G7, D10,E10, H7,D1,E1, F10,G10, G1,H1,E2, D11,E11, F2,G2,H2, F11,G11, K1,L1,N1, D1,E1,F1, P1,K2,L2, G1,D2,E2, F2,G2,J1, M2,N2 K1,L1,M1, J2,K2,L2 M2, I/O Description I/OBidirectional Data I/O lines. As inputs, they Synchronous feed into an on-chip data register that is triggered by the rising edge of CLK. As outputs, they deliver the data contained in the memory location specified by the addresses presented during the previous clock rise of the read cycle. The direction of the pins is controlled by OE. When OE is asserted LOW, the pins behave as outputs. When HIGH, DQs and DQP[A:D] are placed in a three-state condition.The outputs are automatically three-stated during the data portion of a write sequence, during the first clock when emerging from a deselected state, and when the device is deselected, regardless of the state of OE. 51,80,1,30 P6,D6,D2, N11,C11,C1, I/OBidirectional Data Parity I/O Lines. P2 N1 Synchronous Functionally, these signals are identical to DQs. During write sequences, DQP[A:D] is controlled by BW[A:D] correspondingly. 31 31 R3 R1 VDD 15,41,65,91 15,41,65,91 J2,C4,J4, R4,J6 D4,D8,E4, E8,F4,F8, G4,G8, H4,H8,J4, J8,K4,K8, L4,L8,M4, M8 VDDQ 4,11,20,27, 4,11,20,27, A1,F1,J1, 54,61,70,77 54,61,70,77 M1,U1, A7,F7,J7, M7,U7 C3,C9,D3, D9,E3,E9, F3,F9,G3, G9,J3,J9, K3,K9,L3, L9,M3,M9, N3,N9 Document #: 38-05302 Rev. *B Input-Static Selects Burst Order. When tied to GND selects linear burst sequence. When tied to VDD or left floating selects interleaved burst sequence. This is a strap pin and should remain static during device operation. Mode Pin has an internal pull-up. Power Supply Power supply inputs to the core of the device. I/O Power Supply Power supply for the I/O circuitry. Page 8 of 34 CY7C1361B CY7C1363B CY7C1361B–Pin Definitions (continued) Name TQFP (3-Chip Enable) TQFP (2-Chip Enable) BGA (2-Chip Enable) fBGA (3-Chip Enable) VSS 17,40,67,90 17,40,67,90 H2,D3,E3, C4,C5,C6, F3,H3,K3, C7,C8,D5, D6,D7,E5, M3,N3, P3,D5,E5, E6,E7,F5, F5,H5,K5, F6,F7,G5, M5,N5,P5 G6,G7,H5, H6,H7,J5, J6,J7,K5,K6, K7,L5,L6,L7, M5,M6,M7, N4,N8 VSSQ 5,10,21,26, 5,10,21,26, 55,60,71,76 55,60,71,76 – – I/O Ground I/O Ground Ground for the core of the device. Ground for the I/O circuitry. Serial data-out to the JTAG circuit. Delivers data on the negative edge of TCK. If the JTAG feature is not being utilized, this pin should be left unconnected. This pin is not available on TQFP packages. TDO – – U5 P7 TDI – – U3 P5 JTAG serial Serial data-In to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG feature input Synchronous is not being utilized, this pin can be left floating or connected to VDD through a pull up resistor. This pin is not available on TQFP packages. TMS – – U2 R5 JTAG serial Serial data-In to the JTAG circuit. Sampled input on the rising edge of TCK. If the JTAG feature Synchronous is not being utilized, this pin can be disconnected or connected to VDD. This pin is not available on TQFP packages. TCK – – U4 R7 JTAGClock A1,A11,B1, B11,C2,C10, H1,H3,H9, H10,N2,N5, N6,N7,N10, P1,P2,R2 – NC VSS/DNU 16,38,39,42, 16,38,39,42, B1,C1,R1, 66 43,66 T1,T2,J3, D4,L4,J5, R5,T6,U6, B7,C7,R7 14 14 - - JTAG serial output Synchronous Description Clock input to the JTAG circuitry. If the JTAG feature is not being utilized, this pin must be connected to VSS. This pin is not available on TQFP packages. No Connects. Not internally connected to the die. 18M, 36M, 72M, 144M and 288M are address expansion pins are not internally connected to the die. Ground/DNU This pin can be connected to Ground or should be left floating. CY7C1363B: Pin Definitions Name A0, A1, A TQFP (3-Chip Enable) TQFP (2-Chip Enable) BGA (2-Chip Enable) fBGA (3-Chip Enable) 37,36,32,33, 34,35,43,44, 45,46,47,48, 49,50,80,81, 82,99,100 37,36,32,33, 34,35,44,45, 46,47,48,49, 50,80,81,82, 92,99,100 P4,N4,A2, C2,R2,T2, A3,B3,C3, T3,A5,B5, C5,T5,A6, B6,C6,R6, T6 R6,P6,A2, A10,A11,B2, B10,P3,P4, P8,P9,P10, P11,R3,R4, R8,R9,R10, R11 Document #: 38-05302 Rev. *B I/O Description InputSynchronous Address Inputs used to select one of the 512K address locations. Sampled at the rising edge of the CLK if ADSP or ADSC is active LOW, and CE1, CE2, and CE3[2] are sampled active. A[1:0] feed the 2-bit counter. Page 9 of 34 CY7C1361B CY7C1363B CY7C1363B: Pin Definitions (continued) Name TQFP (3-Chip Enable) TQFP (2-Chip Enable) BGA (2-Chip Enable) fBGA (3-Chip Enable) BWA,BWB 93,94 93,94 L5,G3 GW 88 88 BWE 87 CLK I/O Description B5,A4 InputSynchronous Byte Write Select Inputs, active LOW. Qualified with BWE to conduct byte writes to the SRAM. Sampled on the rising edge of CLK. H4 B7 InputSynchronous Global Write Enable Input, active LOW. When asserted LOW on the rising edge of CLK, a global write is conducted (ALL bytes are written, regardless of the values on BW[A:B] and BWE). 87 M4 A7 InputSynchronous Byte Write Enable Input, active LOW. Sampled on the rising edge of CLK. This signal must be asserted LOW to conduct a byte write. 89 89 K4 B6 InputClock Clock Input. Used to capture all synchronous inputs to the device. Also used to increment the burst counter when ADV is asserted LOW, during a burst operation. 98 98 E4 A3 InputSynchronous Chip Enable 1 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE2 and CE3[2] to select/deselect the device. ADSP is ignored if CE1 is HIGH. CE2 97 97 B2 B3 InputSynchronous Chip Enable 2 Input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction with CE1 and CE3[2] to select/deselect the device. CE3[2] 92 – – A6 InputSynchronous Chip Enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE1 and CE2 to select/deselect the device. OE 86 86 F4 B8 InputOutput Enable, asynchronous input, Asynchronous active LOW. Controls the direction of the I/O pins. When LOW, the I/O pins behave as outputs. When deasserted HIGH, I/O pins are three-stated, and act as input data pins. OE is masked during the first clock of a read cycle when emerging from a deselected state. ADV 83 83 G4 A9 InputSynchronous Advance Input signal, sampled on the rising edge of CLK. When asserted, it automatically increments the address in a burst cycle. ADSP 84 84 A4 B9 InputSynchronous Address Strobe from Processor, sampled on the rising edge of CLK, active LOW. When asserted LOW, addresses presented to the device are captured in the address registers. A[1:0] are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. ASDP is ignored when CE1 is deasserted HIGH. CE1 Document #: 38-05302 Rev. *B Page 10 of 34 CY7C1361B CY7C1363B CY7C1363B: Pin Definitions (continued) TQFP (3-Chip Enable) TQFP (2-Chip Enable) BGA (2-Chip Enable) fBGA (3-Chip Enable) ADSC 85 85 B4 ZZ 64 64 T7 Name DQs DQP[A:B] MODE I/O Description A8 InputSynchronous Address Strobe from Controller, sampled on the rising edge of CLK, active LOW. When asserted LOW, addresses presented to the device are captured in the address registers. A[1:0] are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. H11 InputZZ “sleep” Input, active HIGH. When Asynchronous asserted HIGH places the device in a non-time-critical “sleep” condition with data integrity preserved. For normal operation, this pin has to be LOW or left floating. ZZ pin has an internal pull-down. 58,59,62,63, 58,59,62,63, P7,K7,G7, J10,K10, 68,69,72,73, 68,69,72,73, E7,F6,H6, L10,M10, 8,9,12,13, 8,9,12,13, L6,N6,D1, D11,E11, 18,19,22,23 18,19,22,23 H1,L1,N1, F11,G11,J1, E2,G2,K2, K1,L1,M1, M2 D2,E2,F2, G2 I/OSynchronous Bidirectional Data I/O lines. As inputs, they feed into an on-chip data register that is triggered by the rising edge of CLK. As outputs, they deliver the data contained in the memory location specified by the addresses presented during the previous clock rise of the read cycle. The direction of the pins is controlled by OE. When OE is asserted LOW, the pins behave as outputs. When HIGH, DQs and DQP[A:B] are placed in a three-state condition.The outputs are automatically three-stated during the data portion of a write sequence, during the first clock when emerging from a deselected state, and when the device is deselected, regardless of the state of OE. 74,24 74,24 D6,P2 C11,N1 I/OSynchronous Bidirectional Data Parity I/O Lines. Functionally, these signals are identical to DQs. During write sequences, DQP[A:B] is controlled by BW[A:B] correspondingly. 31 31 R3 R1 Input-Static Selects Burst Order. When tied to GND selects linear burst sequence. When tied to VDD or left floating selects interleaved burst sequence. This is a strap pin and should remain static during device operation. Mode Pin has an internal pull-up. VDD 15,41,65,91 15,41,65,91 C4,J2,J4, J6,R4 D4,D8,E4, E8,F4,F8, G4,G8, H4,H8,J4, J8,K4,K8, L4,L8,M4, M8 VDDQ 4,11,20,27, 4,11,20,27, A1,A7,F1, 54,61,70,77 54,61,70,77 F7,J1,J7, M1,M7,U1 ,U7 C3,C9,D3, D9,E3,E9, F3,F9,G3, G9,J3,J9, K3,K9,L3, L9,M3,M9, N3,N9 Document #: 38-05302 Rev. *B Power Supply Power supply inputs to the core of the device. I/O Power Supply Power supply for the I/O circuitry. Page 11 of 34 CY7C1361B CY7C1363B CY7C1363B: Pin Definitions (continued) Name TQFP (3-Chip Enable) TQFP (2-Chip Enable) BGA (2-Chip Enable) fBGA (3-Chip Enable) VSS 17,40,67,90 17,40,67,90 D3,D5,E3, C4,C5,C6, E5,F3,F5, C7,C8,D5, D6,D7,E5, G5,H3, H5,K3,K5, E6,E7,F5, F6,F7,G5, L3,M3, G6,G7,H1, M5,N3, N5,P3,P5 H2,H5,H6, H7,J5,J6,J7, K5,K6,K7,L5 ,L6,L7,M5, M6,M7,N4, N8 VSSQ 5,10,21,26, 5,10,21,26, 55,60,71,76, 55,60,71,76, I/O Ground – – I/O Ground Description Ground for the core of the device. Ground for the I/O circuitry. TDO – – U5 P7 JTAG serial output Synchronous Serial data-out to the JTAG circuit. Delivers data on the negative edge of TCK. If the JTAG feature is not being utilized, this pin should be left unconnected. This pin is not available on TQFP packages. TDI – – U3 P5 JTAG serial input Synchronous Serial data-In to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG feature is not being utilized, this pin can be left floating or connected to VDD through a pull up resistor. This pin is not available on TQFP packages. TMS – – U2 R5 JTAG serial input Synchronous Serial data-In to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG feature is not being utilized, this pin can be disconnected or connected to VDD. This pin is not available on TQFP packages. TCK – – U4 R7 JTAGClock Clock input to the JTAG circuitry. If the JTAG feature is not being utilized, this pin must be connected to VSS. This pin is not available on TQFP packages. NC 1,2,3,6,7,16, 25,28,29,30, 38,39,42,51, 52,53,56,57, 66,75,78,79, 95,96 1,2,3,6,7,16, 25,28,29,30, 38,39,42,43, 51,52,53,56, 57,66,75,78, 79,95,96 B1,B7,C1, C7,D2,D4, D7,E1,E6, H2,F2,G1, G6,H7,J3, J5,K1,K6, L4,L2,L7, M6,N2,N7 ,L7,P1,P6, R1,R5,R7, T1,T4,U6 A1,A5,B1, B4,B11,C1, C2,C10,D1, D10,E1,E10, F1,F10,G1, G10,H3,H9, H10,J2,J11, K2,K11,L2, L11,M2,M11, N2,N5,N6, N7,N10,N11, P1,P2,R2 – No Connects. Not internally connected to the die. 18M, 36M, 72M, 144M and 288M are address expansion pins are not internally connected to the die. 14 14 – – Ground/DNU VSS/DNU Document #: 38-05302 Rev. *B This pin can be connected to Ground or should be left floating. Page 12 of 34 CY7C1361B CY7C1363B Functional Overview All synchronous inputs pass through input registers controlled by the rising edge of the clock. Maximum access delay from the clock rise (t C0) is 6.5 ns (133-MHz device). The CY7C1361B/CY7C1363B supports secondary cache in systems utilizing either a linear or interleaved burst sequence. The interleaved burst order supports Pentium® and i486 processors. The linear burst sequence is suited for processors that utilize a linear burst sequence. The burst order is user-selectable, and is determined by sampling the MODE input. Accesses can be initiated with either the Processor Address Strobe (ADSP) or the Controller Address Strobe (ADSC). Address advancement through the burst sequence is controlled by the ADV input. A two-bit on-chip wraparound burst counter captures the first address in a burst sequence and automatically increments the address for the rest of the burst access. Byte write operations are qualified with the Byte Write Enable (BWE) and Byte Write Select (BWX) inputs. A Global Write Enable (GW) overrides all byte write inputs and writes data to all four bytes. All writes are simplified with on-chip synchronous self-timed write circuitry. Three synchronous Chip Selects (CE1, CE2, CE3[2]) and an asynchronous Output Enable (OE) provide for easy bank selection and output three-state control. ADSP is ignored if CE1 is HIGH. Single Read Accesses A single read access is initiated when the following conditions are satisfied at clock rise: (1) CE1, CE2, and CE3[2] are all asserted active, and (2) ADSP or ADSC is asserted LOW (if the access is initiated by ADSC, the write inputs must be deasserted during this first cycle). The address presented to the address inputs is latched into the address register and the burst counter/control logic and presented to the memory core. If the OE input is asserted LOW, the requested data will be available at the data outputs a maximum to tCDV after clock rise. ADSP is ignored if CE1 is HIGH. Single Write Accesses Initiated by ADSP This access is initiated when the following conditions are satisfied at clock rise: (1) CE1, CE2, CE3[2] are all asserted active, and (2) ADSP is asserted LOW. The addresses presented are loaded into the address register and the burst inputs (GW, BWE, and BWX)are ignored during this first clock cycle. If the write inputs are asserted active (see Write Cycle Descriptions table for appropriate states that indicate a write) on the next clock rise, the appropriate data will be latched and written into the device.Byte writes are allowed. All I/Os are three-stated during a byte write.Since this is a common I/O device, the asynchronous OE input signal must be deasserted and the I/Os must be three-stated prior to the presentation of data to DQs. As a safety precaution, the data lines are three-stated once a write cycle is detected, regardless of the state of OE. Document #: 38-05302 Rev. *B Single Write Accesses Initiated by ADSC This write access is initiated when the following conditions are satisfied at clock rise: (1) CE1, CE2, and CE3[2] are all asserted active, (2) ADSC is asserted LOW, (3) ADSP is deasserted HIGH, and (4) the write input signals (GW, BWE, and BWX) indicate a write access. ADSC is ignored if ADSP is active LOW. The addresses presented are loaded into the address register and the burst counter/control logic and delivered to the memory core. The information presented to DQ[A:D] will be written into the specified address location. Byte writes are allowed. All I/Os are three-stated when a write is detected, even a byte write. Since this is a common I/O device, the asynchronous OE input signal must be deasserted and the I/Os must be three-stated prior to the presentation of data to DQs. As a safety precaution, the data lines are three-stated once a write cycle is detected, regardless of the state of OE. Burst Sequences The CY7C1361B/CY7C1363B provides an on-chip two-bit wraparound burst counter inside the SRAM. The burst counter is fed by A[1:0], and can follow either a linear or interleaved burst order. The burst order is determined by the state of the MODE input. A LOW on MODE will select a linear burst sequence. A HIGH on MODE will select an interleaved burst order. Leaving MODE unconnected will cause the device to default to a interleaved burst sequence. Interleaved Burst Address Table (MODE = Floating or VDD) First Address A1: A0 Second Address A1: A0 Third Address A1: A0 Fourth Address A1: A0 00 01 10 11 01 00 11 10 10 11 00 01 11 10 01 00 Linear Burst Address Table (MODE = GND) First Address A1: A0 Second Address A1: A0 Third Address A1: A0 Fourth Address A1: A0 00 01 10 11 01 10 11 00 10 11 00 01 11 00 01 10 Sleep Mode The ZZ input pin is an asynchronous input. Asserting ZZ places the SRAM in a power conservation “sleep” mode. Two clock cycles are required to enter into or exit from this “sleep” mode. While in this mode, data integrity is guaranteed. Accesses pending when entering the “sleep” mode are not considered valid nor is the completion of the operation guaranteed. The device must be deselected prior to entering the “sleep” mode. CE1, CE2, CE3[2], ADSP, and ADSC must remain inactive for the duration of tZZREC after the ZZ input returns LOW. Page 13 of 34 CY7C1361B CY7C1363B ZZ Mode Electrical Characteristics Parameter IDDZZ tZZS tZZREC tZZI tRZZI Description Test Conditions Snooze mode standby current Device operation to ZZ ZZ recovery time ZZ active to snooze current ZZ Inactive to exit snooze current Min. ZZ > VDD – 0.2V ZZ > VDD – 0.2V ZZ < 0.2V This parameter is sampled This parameter is sampled Max. Unit 35 2tCYC mA ns ns ns ns 2tCYC 2tCYC 0 Truth Table[ 3, 4, 5, 6, 7] Cycle Description Address Used CE1 CE2 CE3 ZZ ADSP ADSC Deselected Cycle, Power-down None H X X L X L ADV WRITE OE CLK X X X L-H three-state DQ Deselected Cycle, Power-down None L L X L L X X X X L-H three-state Deselected Cycle, Power-down None L X H L L X X X X L-H three-state Deselected Cycle, Power-down None L L X L H L X X X L-H three-state Deselected Cycle, Power-down None X X X L H L X X X L-H three-state Snooze Mode, Power-down None X X X H X X X X X X three-state Read Cycle, Begin Burst Read Cycle, Begin Burst Write Cycle, Begin Burst Read Cycle, Begin Burst Read Cycle, Begin Burst Read Cycle, Continue Burst Read Cycle, Continue Burst Read Cycle, Continue Burst External External External External External Next Next Next L L L L L X X H H H H H H X X X L L L L L X X X L L L L L L L L L L H H H H H X X X L L L H H H X X X X X L L L X X L H H H H H L H X L H L H L L-H L-H L-H L-H L-H L-H L-H L-H Q three-state D Q three-state Q three-state Q Read Cycle, Continue Burst Next H X X L X H L H H L-H three-state Write Cycle, Continue Burst Next X X X L H H L L X L-H D Write Cycle, Continue Burst Next H X X L X H L L X L-H D Read Cycle, Suspend Burst Current X X X L H H H H L L-H Q Read Cycle, Suspend Burst Current X X X L H H H H H L-H three-state Read Cycle, Suspend Burst Current H X X L X H H H L L-H Q Read Cycle, Suspend Burst Current H X X L X H H H H L-H three-state Write Cycle, Suspend Burst Current X X X L H H H L X L-H D Write Cycle, Suspend Burst Current H X X L X H H L X L-H D Notes: 3. X=”Don't Care.” H = Logic HIGH, L = Logic LOW. 4. WRITE = L when any one or more Byte Write enable signals and BWE = L or GW= L. WRITE = H when all Byte write enable signals, BWE, GW = H. 5. The DQ pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock. 6. The SRAM always initiates a read cycle when ADSP is asserted, regardless of the state of GW, BWE, or BWX. Writes may occur only on subsequent clocks after the ADSP or with the assertion of ADSC. As a result, OE must be driven HIGH prior to the start of the write cycle to allow the outputs to three-state. OE is a don't care for the remainder of the write cycle. 7. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle all data bits are three-state when OE is inactive or when the device is deselected, and all data bits behave as output when OE is active (LOW). 3 Document #: 38-05302 Rev. *B Page 14 of 34 CY7C1361B CY7C1363B Partial Truth Table for Read/Write[3, 8] Function (CY7C1361B) BWE H BWD Read GW H BWC BWB BWA X X X X Read H L H H H H Write Byte (A, DQPA) H L H H H L Write Byte (B, DQPB) H L H H L H Write Bytes (B, A, DQPA, DQPB) H L H H L L Write Byte (C, DQPC) H L H L H H Write Bytes (C, A, DQPC, DQPA) H L H L H L Write Bytes (C, B, DQPC, DQPB) H L H L L H Write Bytes (C, B, A, DQPC, DQPB, DQPA) H L H L L L Write Byte (D, DQPD) H L L H H H Write Bytes (D, A, DQPD, DQPA) H L L H H L Write Bytes (D, B, DQPD, DQPA) H L L H L H Write Bytes (D, B, A, DQPD, DQPB, DQPA) H L L H L L Write Bytes (D, B, DQPD, DQPB) H L L L H H Write Bytes (D, B, A, DQPD, DQPC, DQPA) H L L L H L Write Bytes (D, C, A, DQPD, DQPB, DQPA) H L L L L H Write All Bytes H L L L L L Write All Bytes L X X X X X Truth Table for Read/Write[3] Function (CY7C1363B) Read GW H BWE H BWB X BWA X Read H L H H Write Byte A – (DQA and DQPA) H L H L Write Byte B – (DQB and DQPB) H L L H Write All Bytes H L L L Write All Bytes L X X X Note: 8. Table only lists a partial listing of the byte write combinations. Any Combination of BWX is valid Appropriate write will be done based on which byte write is active. Document #: 38-05302 Rev. *B Page 15 of 34 CY7C1361B CY7C1363B IEEE 1149.1 Serial Boundary Scan (JTAG) Test MODE SELECT (TMS) The CY7C1361B/CY7C1363B incorporates a serial boundary scan test access port (TAP). This port operates in accordance with IEEE Standard 1149.1-1990 but does not have the set of functions required for full 1149.1 compliance. These functions from the IEEE specification are excluded because their inclusion places an added delay in the critical speed path of the SRAM. Note that the TAP controller functions in a manner that does not conflict with the operation of other devices using 1149.1 fully compliant TAPs. The TAP operates using JEDEC-standard 3.3V or 2.5V I/O logic levels. The CY7C1361B/CY7C1363B contains a TAP controller, instruction register, boundary scan register, bypass register, and ID register. Disabling the JTAG Feature It is possible to operate the SRAM without using the JTAG feature. To disable the TAP controller, TCK must be tied LOW(VSS) to prevent clocking of the device. TDI and TMS are internally pulled up and may be unconnected. They may alternately be connected to VDD through a pull-up resistor. TDO should be left unconnected. Upon power-up, the device will come up in a reset state which will not interfere with the operation of the device. The TMS input is used to give commands to the TAP controller and is sampled on the rising edge of TCK. It is allowable to leave this ball unconnected if the TAP is not used. The ball is pulled up internally, resulting in a logic HIGH level. Test Data-In (TDI) The TDI ball is used to serially input information into the registers and can be connected to the input of any of the registers. The register between TDI and TDO is chosen by the instruction that is loaded into the TAP instruction register. For information on loading the instruction register, see Figure . TDI is internally pulled up and can be unconnected if the TAP is unused in an application. TDI is connected to the most significant bit (MSB) of any register. (See Tap Controller Block Diagram.) Test Data-Out (TDO) The TDO output ball is used to serially clock data-out from the registers. The output is active depending upon the current state of the TAP state machine. The output changes on the falling edge of TCK. TDO is connected to the least significant bit (LSB) of any register. (See Tap Controller State Diagram.) TAP Controller Block Diagram TAP Controller State Diagram 1 0 Bypass Register TEST-LOGIC RESET 2 1 0 0 0 RUN-TEST/ IDLE 1 SELECT DR-SCAN 1 SELECT IR-SCAN 0 1 1 CAPTURE-DR 0 TDO x . . . . . 2 1 0 SHIFT-IR 0 Boundary Scan Register 1 EXIT1-DR 1 EXIT1-IR 0 1 TCK 0 PAUSE-DR 0 PAUSE-IR 1 0 TMS TAP CONTROLLER 1 EXIT2-DR 0 EXIT2-IR 1 Performing a TAP Reset 1 UPDATE-DR 0 UPDATE-IR 1 0 The 0/1 next to each state represents the value of TMS at the rising edge of TCK. Test Access Port (TAP) Test Clock (TCK) The test clock is used only with the TAP controller. All inputs are captured on the rising edge of TCK. All outputs are driven from the falling edge of TCK. Document #: 38-05302 Rev. *B Selection Circuitry Identification Register CAPTURE-IR 1 Instruction Register 31 30 29 . . . 2 1 0 0 SHIFT-DR 1 TDI Selection Circuitry 0 0 0 1 A RESET is performed by forcing TMS HIGH (VDD) for five rising edges of TCK. This RESET does not affect the operation of the SRAM and may be performed while the SRAM is operating. At power-up, the TAP is reset internally to ensure that TDO comes up in a High-Z state. TAP Registers Registers are connected between the TDI and TDO balls and allow data to be scanned into and out of the SRAM test circuitry. Only one register can be selected at a time through the instruction register. Data is serially loaded into the TDI ball on the rising edge of TCK. Data is output on the TDO ball on the falling edge of TCK. Page 16 of 34 CY7C1361B CY7C1363B Instruction Register Three-bit instructions can be serially loaded into the instruction register. This register is loaded when it is placed between the TDI and TDO balls as shown in the Tap Controller Block Diagram. Upon power-up, the instruction register is loaded with the IDCODE instruction. It is also loaded with the IDCODE instruction if the controller is placed in a reset state as described in the previous section. When the TAP controller is in the Capture-IR state, the two least significant bits are loaded with a binary “01” pattern to allow for fault isolation of the board-level serial test data path. Bypass Register Instructions are loaded into the TAP controller during the Shift-IR state when the instruction register is placed between TDI and TDO. During this state, instructions are shifted through the instruction register through the TDI and TDO balls. To execute the instruction once it is shifted in, the TAP controller needs to be moved into the Update-IR state. EXTEST EXTEST is a mandatory 1149.1 instruction which is to be executed whenever the instruction register is loaded with all 0s. EXTEST is not implemented in this SRAM TAP controller, and therefore this device is not compliant to 1149.1. The TAP controller does recognize an all-0 instruction. To save time when serially shifting data through registers, it is sometimes advantageous to skip certain chips. The bypass register is a single-bit register that can be placed between the TDI and TDO balls. This allows data to be shifted through the SRAM with minimal delay. The bypass register is set LOW (VSS) when the BYPASS instruction is executed. When an EXTEST instruction is loaded into the instruction register, the SRAM responds as if a SAMPLE/PRELOAD instruction has been loaded. There is one difference between the two instructions. Unlike the SAMPLE/PRELOAD instruction, EXTEST places the SRAM outputs in a High-Z state. Boundary Scan Register IDCODE The boundary scan register is connected to all the input and bidirectional balls on the SRAM. The SRAM has a 71-bit-long register. The boundary scan register is loaded with the contents of the RAM I/O ring when the TAP controller is in the Capture-DR state and is then placed between the TDI and TDO balls when the controller is moved to the Shift-DR state. The EXTEST, SAMPLE/PRELOAD and SAMPLE Z instructions can be used to capture the contents of the I/O ring. The Boundary Scan Order tables show the order in which the bits are connected. Each bit corresponds to one of the bumps on the SRAM package. The MSB of the register is connected to TDI, and the LSB is connected to TDO. Identification (ID) Register The IDCODE instruction causes a vendor-specific, 32-bit code to be loaded into the instruction register. It also places the instruction register between the TDI and TDO balls and allows the IDCODE to be shifted out of the device when the TAP controller enters the Shift-DR state. The IDCODE instruction is loaded into the instruction register upon power-up or whenever the TAP controller is given a test logic reset state. SAMPLE Z The SAMPLE Z instruction causes the boundary scan register to be connected between the TDI and TDO balls when the TAP controller is in a Shift-DR state. It also places all SRAM outputs into a High-Z state. SAMPLE/PRELOAD The ID register is loaded with a vendor-specific, 32-bit code during the Capture-DR state when the IDCODE command is loaded in the instruction register. The IDCODE is hardwired into the SRAM and can be shifted out when the TAP controller is in the Shift-DR state. The ID register has a vendor code and other information described in the Identification Register Definitions table. SAMPLE/PRELOAD is a 1149.1 mandatory instruction. The PRELOAD portion of this instruction is not implemented, so the device TAP controller is not fully 1149.1 compliant. TAP Instruction Set The user must be aware that the TAP controller clock can only operate at a frequency up to 10 MHz, while the SRAM clock operates more than an order of magnitude faster. Because there is a large difference in the clock frequencies, it is possible that during the Capture-DR state, an input or output will undergo a transition. The TAP may then try to capture a signal while in transition (metastable state). This will not harm the device, but there is no guarantee as to the value that will be captured. Repeatable results may not be possible. Overview Eight different instructions are possible with the three bit instruction register. All combinations are listed in the Instruction Codes table. Three of these instructions are listed as RESERVED and should not be used. The other five instructions are described in detail below. The TAP controller used in this SRAM is not fully compliant to the 1149.1 convention because some of the mandatory 1149.1 instructions are not fully implemented. The TAP controller cannot be used to load address data or control signals into the SRAM and cannot preload the I/O buffers. The SRAM does not implement the 1149.1 commands EXTEST or INTEST or the PRELOAD portion of SAMPLE/PRELOAD; rather, it performs a capture of the I/O ring when these instructions are executed. Document #: 38-05302 Rev. *B When the SAMPLE/PRELOAD instruction is loaded into the instruction register and the TAP controller is in the Capture-DR state, a snapshot of data on the inputs and bidirectional balls is captured in the boundary scan register. To guarantee that the boundary scan register will capture the correct value of a signal, the SRAM signal must be stabilized long enough to meet the TAP controller’s capture setup plus hold time (tCS plus tCH). The SRAM clock input might not be captured correctly if there is no way in a design to stop (or slow) the clock during a SAMPLE/PRELOAD instruction. If this is an issue, it is still Page 17 of 34 CY7C1361B CY7C1363B BYPASS possible to capture all other signals and simply ignore the value of the CLK captured in the boundary scan register. When the BYPASS instruction is loaded in the instruction register and the TAP is placed in a Shift-DR state, the bypass register is placed between the TDI and TDO balls. The advantage of the BYPASS instruction is that it shortens the boundary scan path when multiple devices are connected together on a board. Once the data is captured, it is possible to shift out the data by putting the TAP into the Shift-DR state. This places the boundary scan register between the TDI and TDO balls. Note that since the PRELOAD part of the command is not implemented, putting the TAP to the Update-DR state while performing a SAMPLE/PRELOAD instruction will have the same effect as the Pause-DR command. Reserved These instructions are not implemented but are reserved for future use. Do not use these instructions. TAP Timing 1 2 Test Clock (TCK) 3 t TH t TMSS t TMSH t TDIS t TDIH t TL 4 5 6 t CYC Test Mode Select (TMS) Test Data-In (TDI) t TDOV t TDOX Test Data-Out (TDO) DON’T CARE UNDEFINED TAP AC Switching Characteristics Over the operating Range[9, 10] Parameter Description Clock tTCYC TCK Clock Cycle Time TCK Clock Frequency tTF tTH TCK Clock HIGH time TCK Clock LOW time tTL Output Times TCK Clock LOW to TDO Valid tTDOV TCK Clock LOW to TDO Invalid tTDOX Setup Times TMS Set-Up to TCK Clock Rise tTMSS TDI Set-Up to TCK Clock Rise tTDIS Capture Set-Up to TCK Rise tCS Hold Times TMS hold after TCK Clock Rise tTMSH TDI Hold after Clock Rise tTDIH tCH Capture Hold after Clock Rise Min. Max. 50 20 25 25 5 0 Unit ns MHz ns ns ns ns 5 5 5 ns ns 5 5 5 ns ns ns Notes: 9. tCS and tCH refer to the setup and hold time requirements of latching data from the boundary scan register. 10. Test conditions are specified using the load in TAP AC test Conditions. T.R/tF = 1ns Document #: 38-05302 Rev. *B Page 18 of 34 CY7C1361B CY7C1363B 3.3V TAP AC Test Conditions 2.5V TAP AC Test Conditions Input pulse levels ........ ........................................VSS to 3.3V Input pulse levels ......................................... VSS to 2.5V Input rise and fall times ...................... ..............................1ns Input rise and fall time ......................................................1ns Input timing reference levels ...........................................1.5V Input timing reference levels................... ......................1.25V Output reference levels...................................................1.5V Output reference levels .................. ..............................1.25V Test load termination supply voltage...............................1.5V Test load termination supply voltage .................... ........1.25V 3.3V TAP AC Output Load Equivalent 2.5V TAP AC Output Load Equivalent 1.5V 1.25V 50Ω 50Ω TDO TDO Z O= 50Ω Z O= 50Ω 20pF 20pF TAP DC Electrical Characteristics And Operating Conditions (0°C < TA < +70°C; VDD = 3.3V ±0.165V unless otherwise noted)[11] Parameter VOH1 VOH2 VOL1 VOL2 VIH VIL IX Description Output HIGH Voltage Output HIGH Voltage Output LOW Voltage Output LOW Voltage DESCRIPTION CONDITIONS MIN IOH = –4.0 mA VDDQ = 3.3V 2.4 V IOH = –1.0 mA VDDQ = 2.5V 2.0 V IOH = –100 µA VDDQ = 3.3V 2.9 V VDDQ = 2.5V 2.1 V UNIT IOL = 8.0 mA VDDQ = 3.3V 0.4 V IOL = 8.0 mA VDDQ = 2.5V 0.4 V IOL = 100 µA VDDQ = 3.3V 0.2 V VDDQ = 2.5V 0.2 V Input HIGH Voltage Input LOW Voltage Input Load Current MAX GND < VIN < VDDQ VDDQ = 3.3V 2.0 VDD + 0.3 V VDDQ = 2.5V 1.7 VDD + 0.3 V VDDQ = 3.3V –0.5 0.7 V VDDQ = 2.5V –0.3 0.7 V –5 5 µA Note: 11. All voltages referenced to VSS (GND). Document #: 38-05302 Rev. *B Page 19 of 34 CY7C1361B CY7C1363B Identification Register Definitions Instruction Field Revision Number (31:29) CY7C1361B (256Kx36) CY7C1363B (512Kx18) 001 001 Description Describes the version number. Device Depth (28:24) 01010 01010 Reserved for Internal Use Device Width (23:18) 000000 000000 Defines memory type and architecture Cypress Device ID (17:12) Cypress JEDEC ID Code (11:1) ID Register Presence Indicator (0) 100110 010110 00000110100 00000110100 1 1 Defines width and density Allows unique identification of SRAM vendor. Indicates the presence of an ID register. Scan Register Sizes Register Name Bit Size (x36) Bit Size (x18) Instruction 3 3 Bypass 1 1 ID 32 32 Boundary Scan Order 71 71 Identification Codes Instruction Code Description EXTEST 000 Captures I/O ring contents. Places the boundary scan register between TDI and TDO. Forces all SRAM outputs to High-Z state. This instruction is not 1149.1-compliant. IDCODE 001 Loads the ID register with the vendor ID code and places the register between TDI and TDO. This operation does not affect SRAM operations. SAMPLE Z 010 Captures I/O ring contents. Places the boundary scan register between TDI and TDO. Forces all SRAM output drivers to a High-Z state. RESERVED 011 Do Not Use: This instruction is reserved for future use. SAMPLE/PRELOAD 100 Captures I/O ring contents. Places the boundary scan register between TDI and TDO. Does not affect SRAM operation. This instruction does not implement 1149.1 preload function and is therefore not 1149.1-compliant. RESERVED 101 Do Not Use: This instruction is reserved for future use. RESERVED 110 Do Not Use: This instruction is reserved for future use. BYPASS 111 Places the bypass register between TDI and TDO. This operation does not affect SRAM operations. Document #: 38-05302 Rev. *B Page 20 of 34 CY7C1361B CY7C1363B 119-Ball BGA Boundary Scan Order CY7C1361B (256K x 36) CY7C1363B (512K x 18) BALL ID Signal Name BIT# BALL ID Signal Name BIT# BALL ID CLK 37 P4 A0 1 2 K4 H4 GW 38 N4 A1 3 M4 BWE 39 R6 A BIT# 1 Signal Name BIT# BALL ID Signal Name CLK 37 P4 A0 2 K4 H4 GW 38 N4 A1 3 M4 BWE 39 R6 A 4 F4 OE 40 T5 A 4 F4 OE 40 T5 A 5 B4 ADSC 41 T3 A 5 B4 ADSC 41 T3 A 6 A4 ADSP 42 R2 A 6 A4 ADSP 42 R2 A 7 G4 ADV 43 R3 MODE 7 G4 ADV 43 R3 MODE 8 C3 A 44 P2 DQPD 8 C3 A 44 Internal Internal 9 B3 A 45 P1 DQD 9 B3 A 45 Internal Internal 10 D6 DQPB 46 L2 DQD 10 T2 A 46 Internal Internal 11 H7 DQB 47 K1 DQD 11 Internal Internal 47 Internal Internal 12 G6 DQB 48 N2 DQD 12 Internal Internal 48 P2 DQPB 13 E6 DQB 49 N1 DQD 13 Internal Internal 49 N1 DQB 14 D7 DQB 50 M2 DQD 14 D6 DQPA 50 M2 DQB 15 E7 DQB 51 L1 DQD 15 E7 DQA 51 L1 DQB 16 F6 DQB 52 K2 DQD 16 F6 DQA 52 K2 DQB 17 G7 DQB 53 Internal Internal 17 G7 DQA 53 Internal Internal 18 H6 DQB 54 H1 DQC 18 H6 DQA 54 H1 DQB 19 T7 ZZ 55 G2 DQC 19 T7 ZZ 55 G2 DQB 20 K7 DQA 56 E2 DQC 20 K7 DQA 56 E2 DQB 21 L6 DQA 57 D1 DQC 21 L6 DQA 57 D1 DQB 22 N6 DQA 58 H2 DQC 22 N6 DQA 58 Internal Internal 23 P7 DQA 59 G1 DQC 23 P7 DQA 59 Internal Internal 24 N7 DQA 60 F2 DQC 24 Internal Internal 60 Internal Internal 25 M6 DQA 61 E1 DQC 25 Internal Internal 61 Internal Internal 26 L7 DQA 62 D2 DQPC 26 Internal Internal 62 Internal Internal 27 K6 DQA 63 C2 A 27 Internal Internal 63 C2 A 28 P6 DQPA 64 A2 A 28 Internal Internal 64 A2 A 29 T4 A 65 E4 CE1 29 T6 A 65 E4 CE1 30 A3 A 66 B2 CE2 30 A3 A 66 B2 CE2 31 C5 A 67 L3 BWD 31 C5 A 67 Internal Internal 32 B5 A 68 G3 BWC 32 B5 A 68 Internal Internal 33 A5 A 69 G5 BWB 33 A5 A 69 G3 BWB 34 C6 A 70 L5 BWA 34 C6 A 70 L5 BWA 35 A6 A 71 Internal Internal 35 A6 A 71 Internal Internal 36 B6 A 36 B6 A Document #: 38-05302 Rev. *B Page 21 of 34 CY7C1361B CY7C1363B 165-Ball fBGA Boundary Scan Order CY7C1361B (256K x 36) BIT# BALL ID Signal Name BIT# 1 B6 CLK 37 CY7C1363B (512K x 18) BALL ID Signal Name BIT# BALL ID Signal Name BIT# BALL ID Signal Name R6 A0 1 B6 CLK 37 R6 A0 2 B7 GW 38 P6 A1 2 B7 GW 38 P6 A1 3 A7 BWE 39 R4 A 3 A7 BWE 39 R4 A 4 B8 OE 40 P4 A 4 B8 OE 40 P4 A 5 A8 ADSC 41 R3 A 5 A8 ADSC 41 R3 A 6 B9 ADSP 42 P3 A 6 B9 ADSP 42 P3 A 7 A9 ADV 43 R1 MODE 7 A9 ADV 43 R1 MODE 8 B10 A 44 N1 DQPD 8 B10 A 44 Internal Internal 9 A10 A 45 L2 DQD 9 A10 A 45 Internal Internal 10 C11 DQPB 46 K2 DQD 10 A11 A 46 Internal Internal 11 E10 DQB 47 J2 DQD 11 Internal Internal 47 Internal Internal 12 F10 DQB 48 M2 DQD 12 Internal Internal 48 N1 DQPB 13 G10 DQB 49 M1 DQD 13 Internal Internal 49 M1 DQB 14 D10 DQB 50 L1 DQD 14 C11 DQPA 50 L1 DQB 15 D11 DQB 51 K1 DQD 15 D11 DQA 51 K1 DQB 16 E11 DQB 52 J1 DQD 16 E11 DQA 52 J1 DQB 17 F11 DQB 53 Internal Internal 17 F11 DQA 53 Internal Internal 18 G11 DQB 54 G2 DQC 18 G11 DQA 54 G2 DQB 19 H11 ZZ 55 F2 DQC 19 H11 ZZ 55 F2 DQB 20 J10 DQA 56 E2 DQC 20 J10 DQA 56 E2 DQB 21 K10 DQA 57 D2 DQC 21 K10 DQA 57 D2 DQB 22 L10 DQA 58 G1 DQC 22 L10 DQA 58 Internal Internal 23 M10 DQA 59 F1 DQC 23 M10 DQA 59 Internal Internal 24 J11 DQA 60 E1 DQC 24 Internal Internal 60 Internal Internal 25 K11 DQA 61 D1 DQC 25 Internal Internal 61 Internal Internal 26 L11 DQA 62 C1 DQPC 26 Internal Internal 62 Internal Internal 27 M11 DQA 63 B2 A 27 Internal Internal 63 B2 A 28 N11 DQPA 64 A2 A 28 Internal Internal 64 A2 A 29 R11 A 65 A3 CE1 29 R11 A 65 A3 CE1 30 R10 A 66 B3 CE2 30 R10 A 66 B3 CE2 31 P10 A 67 B4 BWD 31 P10 A 67 Internal Internal 32 R9 A 68 A4 BWC 32 R9 A 68 Internal Internal 33 P9 A 69 A5 BWB 33 P9 A 69 A4 BWB 34 R8 A 70 B5 BWA 34 R8 A 70 B5 BWA 35 P8 A 71 A6 CE3 35 P8 A 71 A6 CE3 36 P11 A 36 P11 A Document #: 38-05302 Rev. *B Page 22 of 34 CY7C1361B CY7C1363B Maximum Ratings Current into Outputs (LOW)......................................... 20 mA (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ................................. –65°C to +150°C Ambient Temperature with Power Applied............................................. –55°C to +125°C Supply Voltage on VDD Relative to GND........ –0.5V to +4.6V DC Voltage Applied to Outputs in three-state ....................................... –0.5V to VDDQ + 0.5V Static Discharge Voltage........................................... >2001V (per MIL-STD-883, Method 3015) Latch-up Current..................................................... >200 mA Operating Range Ambient Range Temperature VDD VDDQ Commercial 0°C to +70°C 3.3V – 5%/+10% 2.5V – 5% to VDD Industrial –40°C to +85°C DC Input Voltage....................................–0.5V to VDD + 0.5V Electrical Characteristics Over the Operating Range [12, 13] Parameter Description VDD VDDQ Power Supply Voltage I/O Supply Voltage VOH Output HIGH Voltage VOL Output LOW Voltage VIH Input HIGH Voltage[12] VIL Input LOW Voltage[12] IX Input Load Test Conditions VDDQ = 3.3V VDDQ = 2.5V VDDQ = 3.3V, VDD = Min., IOH = –4.0 mA VDDQ = 2.5V, VDD = Min., IOH = –1.0 mA VDDQ = 3.3V, VDD = Min., IOL = 8.0 mA VDDQ = 2.5V, VDD = Min., IOL = 1.0 mA VDDQ = 3.3V VDDQ = 2.5V VDDQ = 3.3V VDDQ = 2.5V GND ≤ VI ≤ VDDQ Input Current of MODE Input = VSS Min. Max. Unit 3.135 3.135 2.375 2.4 2.0 3.6 VDD 2.625 V V V V V V V V V V V µA 2.0 1.7 –0.3 –0.3 –5 5 Input = VSS Output Leakage Current GND ≤ VI ≤ VDD, Output Disabled IOS Output Short Circuit Current VDD = Max., VOUT = GND IDD VDD Operating Supply Current VDD = Max., IOUT = 0 mA, f = fMAX = 1/tCYC Max. VDD, Device Deselected, VIN ≥ VIH or VIN ≤ VIL, f = fMAX, inputs switching µA µA –5 Input = VDD IOZ µA –30 Input = VDD Input Current of ZZ 0.4 0.4 VDD + 0.3V VDD + 0.3V 0.8 0.7 5 30 µA 5 µA -300 µA 7.5-ns cycle, 133 MHz 250 mA 8.8-ns cycle, 117 MHz 220 mA 10-ns cycle, 100 MHz 180 All speeds 40 mA –5 ISB1 Automatic CE Power-down Current—TTL Inputs ISB2 Automatic CE Max. VDD, Device Deselected, Power-down VIN ≥ VDD – 0.3V or VIN ≤ 0.3V, Current—CMOS Inputs f = 0, inputs static All speeds 30 mA ISB3 Max. VDD, Device Deselected, Automatic CE Power-down VIN ≥ VDDQ – 0.3V or VIN ≤ 0.3V, Current—CMOS Inputs f = fMAX, inputs switching All speeds 40 mA ISB4 Automatic CE Power-down Current—TTL Inputs All Speeds 40 mA Max. VDD, Device Deselected, VIN ≥ VDD – 0.3V or VIN ≤ 0.3V, f = 0, inputs static Notes: 12. Overshoot: VIH(AC) < VDD +1.5V (Pulse width less than tCYC/2), undershoot: VIL(AC) > -2V (Pulse width less than tCYC/2). 13. TPower-up: Assumes a linear ramp from 0v to VDD(min.) within 200ms. During this time VIH < VDD and VDDQ < VDD Document #: 38-05302 Rev. *B Page 23 of 34 CY7C1361B CY7C1363B Thermal Resistance[14] Parameter Description ΘJA Thermal Resistance (Junction to Ambient) ΘJC Thermal Resistance (Junction to Case) Test Conditions Test conditions follow standard test methods and procedures for measuring thermal impedance, per EIA / JESD51. TQFP Package BGA Package fBGA Package Unit 25 25 27 °C/W 9 6 6 °C/W Capacitance[14] Parameter Description Test Conditions CIN Input Capacitance CCLK Clock Input Capacitance CI/O Input/Output Capacitance TQFP Package TA = 25°C, f = 1 MHz, VDD = 3.3V. VDDQ = 2.5V BGA Package fBGA Package Unit 5 5 5 pF 5 5 5 pF 5 7 7 pF AC Test Loads and Waveforms 3.3V I/O Test Load R = 317Ω 3.3V OUTPUT OUTPUT RL = 50Ω Z0 = 50Ω GND 5 pF R = 351Ω INCLUDING JIG AND SCOPE 10% 90% 10% 90% ≤ 1ns ≤ 1ns VL = 1.5V (a) ALL INPUT PULSES VDD (c) (b) 2.5V I/O Test Load R = 1667Ω 2.5V OUTPUT OUTPUT RL = 50Ω Z0 = 50Ω VL = 1.25V (a) ALL INPUT PULSES VDD GND 5 pF INCLUDING JIG AND SCOPE R =1538Ω (b) 10% 90% 10% 90% ≤ 1ns ≤ 1ns (c) Note: 14. Tested initially and after any design or process change that may affect these parameters. Document #: 38-05302 Rev. *B Page 24 of 34 CY7C1361B CY7C1363B Switching Characteristics Over the Operating Range[19, 20] 133 MHz Parameter tPOWER Description Min. VDD(Typical) to the first Access[15] Max. 117 MHz Min. Max. 100 MHz Min. Max. Unit 1 1 1 ms 7.5 8.5 10 ns Clock tCYC Clock Cycle Time tCH Clock HIGH 3.0 3.2 4.0 ns tCL Clock LOW 3.0 3.2 4.0 ns Output Times tCDV Data Output Valid After CLK Rise tDOH Data Output Hold After CLK Rise 2.0 2.0 2.0 ns tCLZ Clock to Low-Z[16, 17, 18] 0 0 0 ns tCHZ High-Z[16, 17, 18] 0 tOEV tOELZ tOEHZ Clock to 6.5 0 3.5 OE LOW to Output Valid OE LOW to Output 3.5 7.5 Low-Z[16, 17, 18] 0 [16, 17, 18] 0 3.5 0 3.5 OE HIGH to Output High-Z 3.5 8.5 3.5 ns 3.5 ns 0 3.5 ns ns 3.5 ns Set-up Times tAS Address Set-up Before CLK Rise 1.5 1.5 1.5 ns tADS ADSP, ADSC Set-up Before CLK Rise 1.5 1.5 1.5 ns 1.5 1.5 ns tWES ADV Set-up Before CLK Rise GW, BWE, BW[A:D] Set-up Before CLK Rise 1.5 1.5 1.5 1.5 ns tDS Data Input Set-up Before CLK Rise 1.5 1.5 1.5 ns tCES Chip Enable Set-up 1.5 1.5 1.5 ns tAH Address Hold After CLK Rise 0.5 0.5 0.5 ns tADH ADSP, ADSC Hold After CLK Rise GW,BWE, BW[A:D] Hold After CLK Rise 0.5 0.5 0.5 ns 0.5 0.5 0.5 ns tADVS Hold Times tWEH ADV Hold After CLK Rise Data Input Hold After CLK Rise 0.5 0.5 0.5 ns tDH 0.5 0.5 0.5 ns tCEH Chip Enable Hold After CLK Rise 0.5 0.5 0.5 ns tADVH Notes: 15. This part has a voltage regulator internally; tPOWER is the time that the power needs to be supplied above VDD(minimum) initially, before a read or write operation can be initiated. 16. tCHZ, tCLZ,tOELZ, and tOEHZ are specified with AC test conditions shown in part (b) of AC Test Loads. Transition is measured ± 200 mV from steady-state voltage. 17. At any given voltage and temperature, tOEHZ is less than tOELZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same data bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed to achieve High-Z prior to Low-Z under the same system conditions 18. This parameter is sampled and not 100% tested. 19. Timing reference level is 1.5V when VDDQ = 3.3V and is 1.25V when VDDQ = 2.5V. 20. Test conditions shown in (a) of AC Test Loads unless otherwise noted. Document #: 38-05302 Rev. *B Page 25 of 34 CY7C1361B CY7C1363B Timing Diagrams Read Cycle Timing[21] tCYC CLK t tADS t CL CH tADH ADSP tADS tADH ADSC tAS tAH A1 ADDRESS A2 t WES t WEH GW, BWE,BW X Deselect Cycle tCES t CEH CE t t ADVS ADVH ADV ADV suspends burst OE t OEV t OEHZ t CLZ Data Out (Q) High-Z Q(A1) t OELZ tCDV t CHZ tDOH Q(A2) Q(A2 + 1) Q(A2 + 2) t CDV Q(A2 + 3) Q(A2) Q(A2 + 1) Q(A2 + 2) Burst wraps around to its initial state Single READ BURST READ DON’T CARE UNDEFINED Note: 21. On this diagram, when CE is LOW: CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH: CE1 is HIGH or CE2 is LOW or CE3 is HIGH. Document #: 38-05302 Rev. *B Page 26 of 34 CY7C1361B CY7C1363B Timing Diagrams (continued) Write Cycle Timing[21, 22] t CYC CLK t tADS t CH CL tADH ADSP tADS ADSC extends burst tADH tADS tADH ADSC tAS tAH A1 ADDRESS A2 A3 Byte write signals are ignored for first cycle when ADSP initiates burst tWES tWEH BWE, BWX t t WES WEH GW tCES tCEH CE tADVS tADVH ADV ADV suspends burst OE t Data in (D) High-Z t OEHZ DS t DH D(A1) D(A2) D(A2 + 1) D(A2 + 1) D(A2 + 2) D(A2 + 3) D(A3) D(A3 + 1) D(A3 + 2) Data Out (Q) BURST READ Single WRITE BURST WRITE DON’T CARE Extended BURST WRITE UNDEFINED Notes: 22. Full width write can be initiated by either GW LOW; or by GW HIGH, BWE LOW and BWX LOW. Document #: 38-05302 Rev. *B Page 27 of 34 CY7C1361B CY7C1363B Timing Diagrams (continued) Read/Write Cycle Timing[21, 23, 24] tCYC CLK t CH tADS tADH tAS tAH t CL ADSP ADSC ADDRESS A1 A2 A3 A4 A5 A6 D(A5) D(A6) t t WES WEH BWE, BWX tCES tCEH CE ADV OE tDS Data In (D) Data Out (Q) High-Z t OEHZ Q(A1) tDH tOELZ D(A3) tCDV Q(A2) Back-to-Back READs Q(A4) Single WRITE Q(A4+1) Q(A4+2) Q(A4+3) BURST READ DON’T CARE Back-to-Back WRITEs UNDEFINED Notes: 23. The data bus (Q) remains in high-Z following a WRITE cycle, unless a new read access is initiated by ADSP or ADSC. 24. GW is HIGH. 25. Device must be deselected when entering ZZ mode. See Cycle Descriptions table for all possible signal conditions to deselect the device. 26. DQs are in high-Z when exiting ZZ sleep mode. Document #: 38-05302 Rev. *B Page 28 of 34 CY7C1361B CY7C1363B Timing Diagrams (continued) ZZ Mode Timing[25, 26] CLK t ZZ ZZ I t ZZREC t ZZI SUPPLY I DDZZ t RZZI ALL INPUTS (except ZZ) DESELECT or READ Only Outputs (Q) High-Z DON’T CARE Ordering Information Speed (MHz) 133 Ordering Code CY7C1361B-133AC Package Name 100-lead Thin Quad Flat Pack (14 x 20 x 1.4 mm) 3 Chip Enables Commercial A101 100-lead Thin Quad Flat Pack (14 x 20 x 1.4 mm) 3 Chip Enables Industrial A101 100-lead Thin Quad Flat Pack (14 x 20 x 1.4 mm) 2 Chip Enables Commercial A101 100-lead Thin Quad Flat Pack (14 x 20 x 1.4 mm) 2 Chip Enables Industrial CY7C1363B-133AI CY7C1361B-133AJC CY7C1363B-133AJC CY7C1361B-133AJI CY7C1363B-133AJI CY7C1361B-133BGC BG119 119-ball (14 x 22 x 2.4 mm) BGA 3 Chip Enables and JTAG Commercial BG119 119-ball (14 x 22 x 2.4 mm) BGA 3 Chip Enables and JTAG Industrial BB165A 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.2 mm) 3 Chip Enables and JTAG Commercial BB165A 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.2 mm) 3 Chip Enables and JTAG Industrial CY7C1363B-133BGC CY7C1361B-133BGI CY7C1363B-133BGI CY7C1361B-133BZC CY7C1363B-133BZC CY7C1361B-133BZI CY7C1363B-133BZI Document #: 38-05302 Rev. *B Operating Range A101 CY7C1363B-133AC CY7C1361B-133AI Part and Package Type Page 29 of 34 CY7C1361B CY7C1363B Ordering Information (continued) Speed (MHz) 117 Ordering Code CY7C1361B-117AC Package Name 100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm) 3 Chip Enables Commercial A101 100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm) 3 Chip Enables Industrial A101 100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm) 2 Chip Enables Commercial A101 100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm) 2 Chip Enables Industrial CY7C1363B-117AI CY7C1361B-117AJC CY7C1363B-117AJC CY7C1361B-117AJI CY7C1363B-117AJI CY7C1361B-117BGC BG119 119-ball (14 x 22 x 2.4 mm) BGA 3 Chip Enables and JTAG Commercial BG119 119-ball (14 x 22 x 2.4 mm) BGA 3 Chip Enables and JTAG Industrial BB165A 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.2mm) 3 Chip Enables and JTAG Commercial BB165A 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.2mm) 3 Chip Enables and JTAG Industrial CY7C1363B-117BGC CY7C1361B-117BGI CY7C1363B-117BGI CY7C1361B-117BZC CY7C1363B-117BZC CY7C1361B-117BZI CY7C1363B-117BZI 100 CY7C1361B-100AC A101 100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm) 3 Chip Enables Commercial A101 100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm) 3 Chip Enables Industrial A101 100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm) 2 Chip Enables Commercial A101 100-lead Thin Quad Flat Pack (14 x 20 x 1.4mm) 2 Chip Enables Industrial CY7C1363B-100AC CY7C1361B-100AI CY7C1363B-100AI CY7C1361B-100AJC CY7C1363B-100AJC CY7C1361B-100AJI CY7C1363B-100AJI CY7C1361B-100BGC BG119 119-ball (14 x 22 x 2.4 mm) BGA 3 Chip Enables and JTAG Commercial BG119 119-ball (14 x 22 x 2.4 mm) BGA 3 Chip Enables and JTAG Industrial BB165A 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.2mm) 3 Chip Enables and JTAG Commercial BB165A 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.2mm) 3 Chip Enables and JTAG Industrial CY7C1363B-100BGC CY7C1361B-100BGI CY7C1363B-100BGI CY7C1361B-100BZC CY7C1363B-100BGC CY7C1361B-100BZI CY7C1363B-100BGI Operating Range A101 CY7C1363B-117AC CY7C1361B-117AI Part and Package Type Shaded areas contain advance information. Please contact your local sales representative for availability of these parts. Document #: 38-05302 Rev. *B Page 30 of 34 CY7C1361B CY7C1363B Package Diagrams 100-Pin Thin Plastic Quad Flatpack (14 x 20 x 1.4 mm) A101 DIMENSIONS ARE IN MILLIMETERS. 16.00±0.20 1.40±0.05 14.00±0.10 100 81 80 1 20.00±0.10 22.00±0.20 0.30±0.08 0.65 TYP. 30 SEE DETAIL 50 0.20 MAX. 1.60 MAX. STAND-OFF 0.05 MIN. 0.15 MAX. 0.25 GAUGE PLANE 0.10 0° MIN. 0°-7° A 51 31 R 0.08 MIN. 0.20 MAX. 12°±1° (8X) SEATING PLANE R 0.08 MIN. 0.20 MAX. 0.60±0.15 0.20 MIN. 1.00 REF. DETAIL Document #: 38-05302 Rev. *B A 51-85050-*A Page 31 of 34 CY7C1361B CY7C1363B Package Diagrams (continued) 119-Lead PBGA (14 x 22 x 2.4 mm) BG119 51-85115-*B Document #: 38-05302 Rev. *B Page 32 of 34 CY7C1361B CY7C1363B Package Diagrams (continued) 165-Ball FBGA (13 x 15 x 1.2 mm) BB165A 51-85122-*C i486 is a trademark, and Intel and Pentium are registered trademarks of Intel Corporation. PowerPC is a trademark of IBM Corporation. All product and company names mentioned in this document are the trademarks of their respective holders. Document #: 38-05302 Rev. *B Page 33 of 34 © Cypress Semiconductor Corporation, 2004. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges. Cypress products are not warranted nor intended to be used for medical, life-support, life-saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. CY7C1361B CY7C1363B Document History Page Document Title: CY7C1361B/CY7C1363B 9-Mbit (256K x 36/512K x 18) Flow-Through SRAM Document #: 38-05302 Rev. *B REV. ECN NO. Issue Date Orig. of Change Description of Change ** 116857 06/24/02 RCS New Data Sheet *A 206502 See ECN NJY Removed Preliminary status Updated Functional Block Diagrams Updated Pin Definitions Added JTAG boundary scan orders Updated timing diagrams *B 225181 See ECN VBL Update Ordering Info section: unshade active part number Document #: 38-05302 Rev. *B Page 34 of 34