Please note that Cypress is an Infineon Technologies Company.
The document following this cover page is marked as “Cypress” document as this is the
company that originally developed the product. Please note that Infineon will continue
to offer the product to new and existing customers as part of the Infineon product
portfolio.
Continuity of document content
The fact that Infineon offers the following product as part of the Infineon product
portfolio does not lead to any changes to this document. Future revisions will occur
when appropriate, and any changes will be set out on the document history page.
Continuity of ordering part numbers
Infineon continues to support existing part numbers. Please continue to use the
ordering part numbers listed in the datasheet for ordering.
www.infineon.com
CY8CKIT-049-4xxx
PSoC® 4 Prototyping Kit Guide
Doc. #: 001-90711 Rev. *J
Cypress Semiconductor
198 Champion Court
San Jose, CA 95134-1709
www.cypress.com
Copyrights
Copyrights
© Cypress Semiconductor Corporation, 2014-2018. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress"). This document,
including any software or firmware included or referenced in this document ("Software"), is owned by
Cypress under the intellectual property laws and treaties of the United States and other countries
worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other
intellectual property rights. If the Software is not accompanied by a license agreement and you do
not otherwise have a written agreement with Cypress governing the use of the Software, then
Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to
sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code
form, to modify and reproduce the Software solely for use with Cypress hardware products, only
internally within your organization, and (b) to distribute the Software in binary code form externally to
end users (either directly or indirectly through resellers and distributors), solely for use on Cypress
hardware product units, and (2) under those claims of Cypress's patents that are infringed by the
Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software
solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF
ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent
permitted by applicable law, Cypress reserves the right to make changes to this document without
further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any
sample design information or programming code, is provided only for reference purposes. It is the
responsibility of the user of this document to properly design, program, and test the functionality and
safety of any application made of this information and any resulting product. Cypress products are
not designed, intended, or authorized for use as critical components in systems designed or
intended for the operation of weapons, weapons systems, nuclear installations, life-support devices
or systems, other medical devices or systems (including resuscitation equipment and surgical
implants), pollution control or hazardous substances management, or other uses where the failure of
the device or system could cause personal injury, death, or property damage ("Unintended Uses"). A
critical component is any component of a device or system whose failure to perform can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness.
Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any
claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products.
You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and
other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, PSoC,
CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the
United States and other countries. For a more complete list of Cypress trademarks, visit
cypress.com. Other names and brands may be claimed as property of their respective owners.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
2
Contents
Safety Information
1. Introduction
1.1
1.2
1.3
1.4
16
Connecting the PSoC 4 Prototyping Kit to a Computer .............................................16
CY8CKIT-049-4xxx USB COM Port ..........................................................................17
Programming a CY8CKIT-049-4xxx Project Using the Bootloader ...........................18
USB-UART Default Settings ......................................................................................25
4. Hardware
4.1
4.2
4.3
13
Before You Begin.......................................................................................................13
CY8CKIT-049-41xx/CY8CKIT-049-42xx Software ....................................................13
Install Software ..........................................................................................................14
Install Hardware.........................................................................................................14
Uninstall Software......................................................................................................14
Open the “PSoC 4 Code” Code Example in PSoC Creator .......................................15
3. Kit Operation
3.1
3.2
3.3
3.4
7
Kit Contents .................................................................................................................7
Getting Started.............................................................................................................8
Additional Learning Resources....................................................................................8
1.3.1 PSoC Creator...................................................................................................9
1.3.2 PSoC Creator Code Examples ......................................................................10
1.3.3 PSoC Creator Help ........................................................................................11
1.3.4 Technical Support...........................................................................................12
Document Conventions .............................................................................................12
2. Software Installation
2.1
2.2
2.3
2.4
2.5
2.6
5
26
Board Details .............................................................................................................26
Theory of Operation...................................................................................................27
Functional Description ...............................................................................................27
4.3.1 Power Supply System ....................................................................................27
4.3.2 Board Separation (Snapping).........................................................................28
4.3.3 Header Connections ......................................................................................28
4.3.4 User and Passive Inputs ................................................................................32
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
3
Contents
5. Code Examples
5.1
5.2
5.3
5.4
6. USB-Serial Configuration
6.1
6.2
53
USB-Serial Resources...............................................................................................53
USB-Serial Configuration Utility .................................................................................54
6.2.1 Connecting to a USB-Serial Device ...............................................................55
6.2.2 Configuring a Serial Port ................................................................................56
6.2.3 Configuring GPIOs .........................................................................................59
6.2.4 Additional Features of the USB-Serial Device ...............................................61
A. Appendix
A.1
A.2
A.3
35
Bootloader Base Code Example................................................................................35
Bootloadable Code Example .....................................................................................36
Creating a New Bootloadable Project........................................................................37
Converting a Non-bootloadable Project to a Bootloadable Project............................40
5.4.1 PWMExample ................................................................................................41
5.4.2 Entering Bootloader Mode from the Bootloadable Application.......................49
62
CY8CKIT-049-4xxx Schematics ................................................................................62
Programming a CY8CKIT-049-4xxx Project Using MiniProg3...................................69
Bill of Materials ..........................................................................................................74
Revision History
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
75
4
Safety Information
Regulatory Compliance
The CY8CKIT-049-4xxx Prototyping Kit is intended for use as a development platform for hardware
or software in a laboratory environment. The board is an open system design, which does not
include a shielded enclosure. This may cause interference to other electrical or electronic devices in
close proximity. In a domestic environment, this product may cause radio interference. In such
cases, you may be required to take adequate preventive measures. In addition, this board should
not be used near any medical equipment or RF devices.
Attaching additional wiring to this product or modifying the product operation from the factory default
may affect its performance and cause interference with other apparatus in the immediate vicinity. If
such interference is detected, suitable mitigating measures should be taken.
The CY8CKIT-049-4xxx Prototyping Kit, as shipped from the factory, has been verified to meet with
requirements of CE as a Class A product.
The CY8CKIT-049-4xxx contains electrostatic discharge
(ESD) sensitive devices. Electrostatic charges readily
accumulate on the human body and any equipment, and
can discharge without detection. Permanent damage may
occur on devices subjected to high-energy discharges.
Proper ESD precautions are recommended to avoid
performance degradation or loss of functionality. Store
unused CY8CKIT-049-4xxx boards in the protective
shipping package.
End-of-Life/Product Recycling
This kit has an end-of life five years from the date of
manufacture mentioned on the back of the box. Contact your
nearest recycler for discarding the kit.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
5
Safety Information
General Safety Instructions
ESD Protection
ESD can damage boards and associated components. Cypress recommends that you perform
procedures only at an ESD workstation. If such a workstation is not available, use appropriate ESD
protection by wearing an antistatic wrist strap attached to the chassis ground (any unpainted metal
surface) on your board when handling parts.
Handling Boards
CY8CKIT-049-4xxx boards are sensitive to ESD. Hold the board only by its edges. After removing
the board from its box, place it on a grounded, static-free surface. Use a conductive foam pad if
available. Do not slide board over any surface.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
6
1.
Introduction
Thank you for your interest in the PSoC® 4 CY8CKIT-049-4xxx family of prototyping kits. The
prototyping kit is designed as an easy-to-use and inexpensive prototyping platform for users wishing
to rapidly develop products using the PSoC 4 families and use the unique flexibility of the PSoC 4
architecture. Designed for flexibility, these kits offer an open footprint breakout board to maximize
the end utility of the PSoC 4 device. These kits provide a low-cost alternative to device samples
while providing a platform to easily develop and integrate the PSoC 4 device into your end system.
In addition, the board includes the following features:
■
Onboard CMOD capacitors to enable CapSense® development
■
A bypass capacitor to ensure the high quality ADC conversions
■
An LED to provide feedback
■
A push button to provide a simple user input and trigger the bootloader programming mode
■
The CY8CKIT-049-41xx PSoC 4 Prototyping kit has CY8C4125AXI-483 device on-board and
CY8CKIT-049-42xx PSoC 4 Prototyping kit has CY8C4245AXI-483 device on-board
The CY8CKIT-049-4xxx development kit also supports the Cypress USB-Serial CY7C65211
Full-Speed USB controller that enables PC connectivity and serial interfaces, such as USB-UART,
USB-I2C, USB-SPI, and USB-GPIO. The development kit includes a Cypress USB-Serial controller
used to bootload the target PSoC 4 device. The PSoC 4 prototyping board is breakable, allowing
you to separate the USB-Serial board from the PSoC 4 board.
This kit supports either 5 V or 3.3 V power supply voltages. The device can be programmed using
the bootloader or the Cypress MiniProg3 programmer. The PSoC 4 Prototyping Kit supports boards
based on the 4100 and 4200 device families, delivering a programmable platform for a wide range of
embedded applications at a very low cost. The PSoC 4 is a scalable and reconfigurable platform
architecture for a family of mixed-signal programmable embedded system controllers with an ARM®
Cortex™-M0 CPU. It combines programmable and reconfigurable analog and digital blocks with
flexible automatic routing.
1.1
Kit Contents
This kit contains only the PSoC 4 Prototyping Kit, either the 4100 or 4200 series device.
Figure 1-1. PSoC 4 CY8CKIT-049-4xxx Prototyping Kit
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
7
Introduction
1.2
Getting Started
This user guide helps you to get acquainted with the PSoC 4 Prototyping Kit. The Software
Installation chapter on page 13 describes the installation of the PSoC Creator software. The Kit
Operation chapter on page 16 explains how to program the kit using a bootloader or a MiniProg3.
The Hardware chapter on page 26 details the hardware operation of the kit. The Code
Examples chapter on page 35 and USB-Serial Configuration chapter on page 53 walk you through
making projects and configuring the USB-Serial device on the kit. The Appendix on page 62
provides the schematics, pin assignment, and bill of materials (BOM).
1.3
Additional Learning Resources
Cypress provides a wealth of data at www.cypress.com to help you to select the right PSoC device
for your design, and to help you to quickly and effectively integrate the device into your design. For a
comprehensive list of resources, see KBA86521, How to Design with PSoC 3, PSoC 4, and
PSoC 5LP. The following is an abbreviated list for PSoC 4:
■
Overview: PSoC Portfolio, PSoC Roadmap
■
Product Selectors: PSoC 1, PSoC 3, PSoC 4, or PSoC 5LP. In addition, PSoC Creator includes
a device selection tool.
■
Datasheets: Describe and provide electrical specifications for the PSoC 4000, PSoC 4100, and
PSoC 4200 device families.
■
CapSense Design Guide: Learn how to design capacitive touch-sensing applications with the
PSoC 4 family of devices.
■
Application Notes and Code Examples: Cover a broad range of topics, from basic to advanced
level. Many of the application notes include code examples. Visit the PSoC 3/4/5 Code Examples
webpage for a list of all available PSoC Creator code examples. For accessing code examples
from within PSoC Creator – see PSoC Creator Code Examples on page 10. These code
examples available across PSoC Creator, Application notes and kits for the most part will NOT be
bootloadable. However, with a very small modification you can port them to a bootloadable
project and use them with the CY8CKIT-049. Refer to Converting a Non-bootloadable Project to
a Bootloadable Project on page 40 for details.
■
Technical Reference Manuals (TRM): Provide detailed descriptions of the architecture and
registers in each PSoC 4 device family.
■
Development Kits:
❐
CY8CKIT-042 and CY8CKIT-040, PSoC 4 Pioneer Kits, are easy-to-use and inexpensive
development platforms. These kits include connectors for Arduino™ compatible shields and
Digilent® Pmod™ daughter cards.
❐
CY8CKIT-049 is a very low-cost prototyping platform for sampling PSoC 4 devices.
❐
CY8CKIT-001 is a common development platform for all PSoC family devices.
■
The MiniProg3 device provides an interface for flash programming and debug.
■
Knowledge Base Articles (KBA): Provide design and application tips from experts on the
devices/kits. For instance, KBA93541, explains how to use CY8CKIT-049 to program another
PSoC 4.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
8
Introduction
1.3.1
PSoC Creator
PSoC Creator is a free Windows-based Integrated Design Environment (IDE). It enables concurrent
hardware and firmware design of systems based on PSoC 3, PSoC 4, and PSoC 5LP. See
Figure 1-2 – with PSoC Creator, you can:
1. Drag and drop Components to build your hardware system design in the main design workspace
2. Codesign your application firmware with the PSoC hardware
3. Configure Components using configuration tools
4. Explore the library of 100+ Components
5. Review Component datasheets
Figure 1-2. PSoC Creator Features
Visit PSoC Creator training page for video tutorials on learning and using PSoC Creator.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
9
Introduction
1.3.2
PSoC Creator Code Examples
PSoC Creator includes a large number of code example projects. These projects are available from
the PSoC Creator Start Page, as Figure 1-3 shows.
Example projects can speed up your design process by starting you off with a complete design,
instead of a blank page. The example projects also show how PSoC Creator Components can be
used for various applications. Code examples and datasheets are included, as Figure 1-4 on
page 11 shows.
In the Find Example Project dialog shown in Figure 1-4 on page 11, you have several options:
■
Filter for examples based on architecture or device family, i.e., PSoC 3, PSoC 4 or PSoC 5LP;
category; or keyword
■
Select from the menu of examples offered based on the Filter Options
■
Review the datasheet for the selection (on the Documentation tab)
■
Review the code example for the selection. You can copy and paste code from this window to
your project, which can help speed up code development, or
■
Create a new project (and a new workspace if needed) based on the selection. This can speed
up your design process by starting you off with a complete, basic design. You can then adapt that
design to your application.
Figure 1-3. Code Examples in PSoC Creator
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
10
Introduction
Figure 1-4. Code Example Projects, with Sample Code
1.3.3
PSoC Creator Help
Visit the PSoC Creator home page to download the latest version of PSoC Creator. Then, launch
PSoC Creator and navigate to the following items:
■
Quick Start Guide: Choose Help > Documentation > Quick Start Guide. This guide gives you
the basics for developing PSoC Creator projects.
■
Simple Component example projects: Choose File > Open > Example projects. These
example projects demonstrate how to configure and use PSoC Creator Components.
■
Starter designs: Choose File > New > Project > PSoC 4 Starter Designs. These starter
designs demonstrate the unique features of PSoC 4.
■
System Reference Guide: Choose Help > System Reference > System Reference Guide.
This guide lists and describes the system functions provided by PSoC Creator.
■
Component datasheets: Right-click a Component and select “Open Datasheet.” Visit the
PSoC 4 Component Datasheets page for a list of all PSoC 4 Component datasheets.
■
Document Manager: PSoC Creator provides a document manager to help you to easily find and
review document resources. To open the document manager, choose the menu item Help >
Document Manager.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
11
Introduction
1.3.4
Technical Support
If you have any questions, our technical support team is happy to assist you. You can create a support request on the Cypress Technical Support page.
If you are in the United States, you can talk to our technical support team by calling our toll-free number: +1-800-541-4736. Select option 2 at the prompt.
You can also use the following support resources if you need quick assistance.
1.4
■
Self-help.
■
Local Sales Office Locations.
Document Conventions
Table 1-1. Document Conventions for Guides
Convention
Usage
Courier New
Displays file locations, user entered text, and source code:
C:\...cd\icc\
Italics
Displays file names and reference documentation:
Read about the sourcefile.hex file in the PSoC Creator User Guide.
[Bracketed, Bold]
Displays keyboard commands in procedures:
[Enter] or [Ctrl] [C]
File > Open
Represents menu paths:
File > Open > New Project
Bold
Displays commands, menu paths, and icon names in procedures:
Click the File icon and then click Open.
Times New Roman
Displays an equation:
2+2=4
Text in gray boxes
Describes Cautions or unique functionality of the product.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
12
2.
2.1
Software Installation
Before You Begin
All Cypress software installations require administrator privileges, but these are not required to run
the software after it is installed. Close any other Cypress software that is currently running before
installing the kit software.
Note: The kit contents are installed in the C:\Program Files\Cypress folder by default. If the
Code examples are being run from the default install location, administrator privileges are required. If
you do not have administrator privileges, copy the Firmware folder from the default install location to
any other location on your PC and access the files
2.2
CY8CKIT-049-41xx/CY8CKIT-049-42xx Software
The kit requires Cypress' proprietary software, such as PSoC Creator, PSoC Programmer and the
USB-Serial Configuration Utility, and generic software such as .NET Framework, Windows Installer,
and Internet Explorer. The kit software is available on the kit web page in three formats:
Table 2-1. Kit Software Formats
Install Package
File Format
Usage
ISO
This package can be used if the PC does not have any
Cypress or non-Cypress prerequisite software installed. It first
installs the prerequisites and then the kit content (firmware,
hardware, and documentation files) in the specified location.
CY8CKIT-049-41xx_Kit Setup/
EXE
CY8CKIT-049-42xx_Kit Setup
This package can be used if the PC does not have any
Cypress prerequisite software installed. If any non-Cypress
prerequisites are found to be missing during installation, the
installer provides links to download and install them and then
installs the kit content (firmware, hardware, and
documentation files) in the specified location.
CY8CKIT-049-41xx_Kit Only/
CY8CKIT-049-42xx_Kit Only
This package can be used if the PC has all the Cypress and
non-Cypress prerequisites installed. It installs only the kit
content (firmware, hardware, and documentation files) in the
specified location. If any of the prerequisites are found
missing during the installation process, the installer prompts
you to install all the required software before attempting to
install the kit. The installer redirects to the kit web page to
download and install any missing Cypress software. Similarly,
it provides links to download and install the missing nonCypress prerequisites.
CY8CKIT-049-41xx_Kit ISO/
CY8CKIT-049-42xx_Kit ISO
EXE
Note: The USB-Serial Configuration Utility requires Visual C++. If Visual C++ is not installed in the
PC, the installer provides link to install the Visual C++ Redistributable package in the PC.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
13
Software Installation
Note: Adobe Reader is required to view kit documents. If Adobe Reader is not installed on your PC,
the installer provides the link to download and install it.
Note: PSoC Creator is provided with a free Keil C licence that has to be registered within 30 days of
installing PSoC Creator. To register your Keil license, you will require an internet connection. Please
read http://www.cypress.com/?id=4&rID=38519 for more details. Please read
http://www.cypress.com/?id=4&rID=44355 if PSoC Creator needs to be used on a PC that does not
have internet connection. The product ID for the Keil compiler is IKA1P-M6Q0E-8W7ST.
2.3
Install Software
1. Run cyautorun.exe in the kit ISO to start the installation process.
2. Click Install CY8CKIT-049-41xx to start CY8CKIT-049-41xx PSoC 4 Prototyping kit installation.
Click Install CY8CKIT-049-42xx to start CY8CKIT-049-42xx PSoC 4 Prototyping kit installation.
3. Select the folder to install the kit files. Choose the directory and click Next. The installation
directory is referred to as in this document.
4. When you click Next, the kit installer automatically installs the required software, if it is not
present on your computer.
5. Select the installation type in the Product Installation Overview window. The drop-down menu
contains three options: Typical (installs all the required features), Custom (lets you choose the
features to be installed), and Complete (installs all the contents). Click Next after you select the
installation type.
Note: It is recommended that you choose the Complete installation type.
6. Read and Accept the End-User License Agreement and click Next to proceed with the
installation.
7. When the installation begins, a list of packages appears on the installation page. A green check
mark appears adjacent to every package after successful installation.
8. After installing all the packages, the CyInstaller finish page opens up. Please provide the
requested contact information or uncheck the “Continue Without Contact Information” checkbox
and click on Finish button to complete the kit installation.
After the installation is complete, the kit contents are available at the following location:
1. For CY8CKIT-049-41xx: \ CY8CKIT-049-41xx \
2. For CY8CKIT-049-42xx: \ CY8CKIT-049-42xx \
2.4
Install Hardware
There is no additional hardware installation required for this kit.
2.5
Uninstall Software
To uninstall the software, do one of the following:
■
Go to Start > All Programs > Cypress > Cypress Update Manager > Cypress Update
Manager, and then select the Uninstall button corresponding to the kit software.
■
Go to Start > Control Panel > Programs and Features, and then select the Uninstall/Change
button corresponding to the kit software.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
14
Software Installation
2.6
Open the “PSoC 4 Code” Code Example in PSoC Creator
Note: The code examples require administrator privileges if they are run directly from the default
install location (C:\Program Files\Cypress). If you do not have administrator privileges, copy the
Firmware folder from the default install location to any other location on your PC and use the files.
1. Launch the PSoC Creator software from the Start menu.
Figure 2-1. PSoC Creator Start Page
2. Open the SCB_Bootloader.cywrk workspace by choosing File > Open > Project/Workspace
and navigating to the directory in which your project is present.
Figure 2-2. Open Project/Workspace
The workspace includes two sample projects linked in the Workspace Explorer. Subsequent
chapters of this user guide show how to build, program, and understand the code examples supplied
with this kit.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
15
3.
Kit Operation
The PSoC 4 Prototyping Kit is simplistic in design and focuses on providing you with complete
access to develop applications using the PSoC 4 device family. The development kit supports a
number of onboard functions such as an LED, push button, through-hole connections, USB-Serial
connectivity to the PC, and a breakable board design to separate the two target boards.
Figure 3-1. PSoC 4 Prototyping Kit
1
2
3
4
5
6
7
8
1. PCB USB Connector (J8)
2. USB-Serial Bridge Controller (U2)
3. Power LED (LED2)
4. Current Measurement Jumper (J4)
5. User LED (LED1)
6. PSoC 4 (U1)
7. Programming Header
8. Push button (SW1)
3.1
Connecting the PSoC 4 Prototyping Kit to a Computer
To use the PSoC 4 Prototyping Kit, you need to connect the kit to a target PC. The kit is designed to
be connected to the computer through USB. The USB connector will provide power to the target
boards and enable serial communication. CY8CKIT-049-4xxx implements a PCB-based USB
connector that makes connections to the USB port when plugged in. The amber LED turns on when
the board is plugged into the port to indicate power.
Figure 3-2. Connecting the PSoC 4 Prototyping Kit to a Computer
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
16
Kit Operation
Figure 3-3. PSoC 4 Prototyping Kit Connected to the Computer
3.2
CY8CKIT-049-4xxx USB COM Port
When you connect the CY8CKIT-049-4xxx to the PC over a USB interface, it enumerates as a COM
port device under the Device Manager window on the Windows OS. Often, the COM port number will
be higher than any existing COM port value. For example, in the following image the
CY8CKIT-049-4xxx enumerates as COM37.
Figure 3-4. CY8CKIT-049-4xxx USB COM Port in Device Manager
When connecting your CY8CKIT-049-4xxx to a computer for the first time or to any new USB port, it
may take a moment to enumerate because the computer will complete an online check for the latest
drivers.
Figure 3-5. Automatic Driver Software Installation for CY8CKIT-049-4xxx
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
17
Kit Operation
Figure 3-6. Driver Software Installation Complete
Note: The baud rate settings do not apply to the virtual COM port as the data transmission is taking
place using the Full-Speed USB bus at 12 Mbps. However, because of the virtual COM port driver
that sits between the PC and the USB-Serial device, the operating system will see the device as a
normal serial port and you will be able to set the baud rate. However, these settings may be ignored.
3.3
Programming a CY8CKIT-049-4xxx Project Using the Bootloader
The following example shows how to bootload (program) a project into the PSoC 4 with the
USB-Serial device, using the Bootloader Host. To use this method, the PSoC 4 device must contain
the bootloader and the project must be configured as bootloadable. This is the default programming
method for new users.
The following steps use the code example included in the kit installer.
1. Launch PSoC Creator from the Start menu.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
18
Kit Operation
2. Open the SCB_Bootloader.cywrk workspace from Examples and Kits > Kits. Select
CY8CKIT-049-41xx folder for CY8CKIT-049-41xx PSoC 4 Prototyping Kit and
CY8CKIT-049-42xx folder for CY8CKIT-049-42xx PSoC 4 Prototyping Kit.
3. Select the folder where you want to save the project and click OK.
Figure 3-7. Open the Project
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
19
Kit Operation
4. Click on Build > Build All Projects.
Note: The UART_Bootloader project is a dependency for the Bootloadable Blinking LED project.
Hence, both example projects must be built by selecting Build > Build All Projects.
5. In the Workspace Explorer, right-click the Bootloadable Blinking LED project and select Set As
Active Project.
Figure 3-8. Set the Code Example as Active Project
The bootloadable project must be associated with the bootloader project's HEX and ELF files.
This will ensure that the firmware code mapping aligns with the code on the target device.
6. Under the 'Bootloadable Blinking LED' code example, double-click the 'TopDesign.cysch' file to
open the schematic view. Select the tab for the Bootloadable Project schematic page if it is not
already selected.
Figure 3-9. Open Schematic View
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
20
Kit Operation
7. In the schematic view, right-click the Bootloadable component and select Configure.
Figure 3-10. Configure the Bootloader Component
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
21
Kit Operation
8. In the configuration window, select the Dependencies tab and click the Browse button to point to
the HEX and ELF files present in the ‘Dependencies’ folder under project directory; click OK. The
file paths (assuming the CY8CKIT-040-42xx) will appear as follows:
\SCB_Bootloader\UART_Bootloader.cydsn\CortexM0\
ARM_GCC_484\Debug\UART_Bootloader.hex
\SCB_Bootloader\UART_Bootloader.cydsn\CortexM0\
ARM_GCC_484\Debug\UART_Bootloader.elf
Figure 3-11. Configure Dependencies for Bootloader Component
9. Select Build > Build Bootloadable Blinking LED.
Figure 3-12. Build the Project
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
22
Kit Operation
10.Connect the CY8CKIT-049-4xxx prototyping board to the PC. When connecting the kit to the port,
depress the SW1 button as it is plugged in.
You will notice that the blue LED begins to blink rapidly; this indicates that the PSoC 4 is in 'Bootloader Mode' and is ready to be loaded with the latest firmware. This must be done each time you
bootload the PSoC 4.
11. Select Tools > Bootloader Host to open the Bootloader Host tool.
Figure 3-13. Launch Bootloader Host Tool
The Bootloader Host tool opens.
Figure 3-14. Bootloader Host Tool
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
23
Kit Operation
12.Click Filters and select the Show UART Devices option from the Port Filters window and click
OK. This lists all COM devices connected to the computer.
Note: The PID of the Bootloader is F13B. You may enter this PID in the Port filters window to list
only the Kit Bootloader.
Figure 3-15. Port Filters
The Bootloader Host tool will now display all of the available UART based COM ports.
13.Click the COM port from the list of available ports and enter the UART configuration such as
Baud Rate, Data Bits, Stop Bits, and Parity for the USB-UART configuration on the USB-Serial
device.
The values for the UART are: 115200 baud rate, 8 data bits, 1 stop bit, and no parity.
14.Click File > Open and navigate to the Bootloadable_Blinking_LED.cyacd file generated in the
CortexM0 folder in your project directory, and click Open.
Figure 3-16. Opening the Generated File
15.Click the Program button to flash the part with your new application code.
The status window provides output message and a status bar indicates the programming progress. When bootloading is complete, your application executes with the latest version of the
application code.
Figure 3-17. Program the Device With Application Code
See application note AN73854 for additional details on bootloading.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
24
Kit Operation
3.4
USB-UART Default Settings
The default configuration of the USB-Serial device on the CY8CKIT-049-4xxx prototyping kit is the
USB-UART mode. The CY8CKIT-049-4xxx also enables a default UART connection between the
USB-Serial device and the PSoC 4. This connection is indicated by two parallel 4-pin headers in the
middle of the board. The default pin connections are shown in Table 3-2.
Table 3-1. Pin Mapping for USB-Serial Port and PSoC 4 UART
USB-Serial UART
TX
PSoC 4 UART
P4.0 (RX)
RX
P4.1 (TX)
GND
GND
VDD
VDD
Figure 3-18. UART Pin Connections on CY8CKIT-049-4xxx
The USB-Serial device provides the PSoC 4 device with an interface to a PC. The USB-Serial
device enumerates as a COM port to allow any terminal software to be used to communicate with
the PSoC 4. To use the USB-UART functionality in the COM terminal software, select the
corresponding COM port. Note that if the USB-Serial device board is separated from the PSoC 4
board, you will still be able to use the USB-Serial device to communicate with any UART device
using the 4-pin header.
The USB-Serial device is by default configured as a USB-UART device with the following
specifications. The USB-UART settings can also be configured from the Cypress USB-Serial
Configuration Utility. The default setting are as shown in bold in the table below.
Table 3-2. USB-UART settings as seen in Cypress USB-Serial Configuration Utility
Parameter
Supported Values
Baud Rate
100, 200, 300, 600, 1200, 2400, 4800, 9600, 14400, 19200, 38400,
56000, 57600, 115200, 230400, 460800, 921600, 1000000, 3000000
Type
2 pin, 4 pin, 6 pin
Data Bits
7 bits, 8 bits
Stop Bits
1 bit, 2 bits
Parity
None, Odd, Even, Mark, Space
Drop Packets on RX error
Disabled, Enabled
Disable CTS and DSR pull-up during
Disabled, Enabled
suspend
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
25
4.
4.1
Hardware
Board Details
The PSoC 4 Prototyping Kit consists of the following blocks:
■
PSoC 4 device
■
PSoC 4 header ports J1 and J2
■
USB-Serial device
■
USB-Serial header ports J5 and J6 (GPIO)
■
UART connection J3 and J4 (SCB and GPIO)
■
PCB USB connector
■
One amber LED (Power)
■
One blue LED (User)
■
Push button
■
External reference capacitor (ADC Bypass)
■
CapSense and shield capacitors (CMOD and CTANK)
■
Programming connector
■
Perforated 'snappable' board design
Figure 4-1. CY8CKIT-049-4xxx Pin Details
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
26
Hardware
4.2
Theory of Operation
PSoC 4 is a new generation of programmable system-on-chip device from Cypress for embedded
applications. It combines programmable analog, programmable digital logic, programmable I/O, and
a high-performance ARM Cortex-M0 core. With PSoC 4, you can create the combination of peripherals required to meet your application's specifications.
The PSoC 4 Prototyping Kit features an onboard USB-Serial device, which communicates to a PC
through USB to provide serial communication support and serial port debugging.
The PSoC 4 Prototyping Kit has a user LED and a power status LED. This kit includes a button that
connects to the PSoC 4 device, which can be used to develop applications. This button is also used
to enable the onboard bootloader. The PSoC 4 pins are brought out onto headers J1 to J2 on the kit
and support 100-mil breadboard spacing.
The PSoC 4 Prototyping Kit can be powered from USB or an external power supply. The input voltage is either 5 V from USB or a variable supply from an external source.
Figure 4-2. CY8CKIT-049-4xxx Functional Block Diagram
4.3
Functional Description
4.3.1
Power Supply System
The power supply system on this board is dependent on the source of the power. For most applications, you can use the 5 V supply from the USB connection to power the system. You can also connect an external power supply to the board for low-voltage applications. The kit supports the
following connections:
■
5 V from the PCB USB
■
1.8-5 V from a regulated supply connected to VDD
It is important to understand that this prototyping kit does not have any onboard ESD protection circuitry. Therefore, the power source for the CY8CKIT-049-4xxx must be of a high quality to ensure
that the board is protected from any over-current conditions and swapped-power connections.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
27
Hardware
4.3.1.1
Measure PSoC 4 Current Consumption
You can measure the current consumption of the PSoC 4 device by using one of these methods:
Method 1:
1. Separate the USB-Serial board by 'snapping' the perforated edge between the two boards.
2. Power the remaining prototyping board via any of the VDD terminals.
3. Place an ammeter in series with the VDD connection to measure the current consumption.
Method 2:
1. Remove the resistor R6 and install a 2-pin jumper in the supplied holes of J4.
2. Connect an ammeter across the 2-pin jumper to measure the current to the PSoC 4 device.
This method can be used either with USB power or with power supplied to one of the VDD pins.
4.3.2
Board Separation (Snapping)
CY8CKIT-049-4xxx supports both the PSoC 4 and USB-Serial boards. To separate the two boards
for testing or development, break the two boards apart at the built-in perforated edge.
The easiest method of separating the two boards is to place the kit on the edge of a table, where the
edge of the table is directly below the perforated edge and the smaller USB-Serial device is off the
table edge. Press gently on the USB-Serial board and snap the two boards apart. If any material is
removed from the edge of the boards, use sheers to clean up the edge of the kit.
Figure 4-3. CY8CKIT-049-4xxx Broken as Two Parts
4.3.3
Header Connections
The CY8CKIT-049-4xxx Prototyping Kit supports a number of unpopulated headers on both the
USB-Serial and the PSoC 4 boards.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
28
Hardware
4.3.3.1
Functionality of the J1 and J2 Headers (PSoC 4)
The main PSoC 4 board contains two dual-inline headers (J1 and J2). These headers are both
1×22-pin headers and include all of the I/O available on the PSoC 4 devices. These headers support
all of the available ports, GND, VDD, and connections to passive elements and user-input devices.
The J1 and J2 headers support 100-mil spacing, so you can solder the male connectors to connect
the CY8CKIT-049-4xxx to any development breadboard.
Figure 4-4. J1 and J2 Headers
Table 4-1. J1 Header Pin Details
PSoC 4 GPIO Header (J1)
Pin
Signal
Description
J1_01
P4.0
GPIO
J1_02
P4.1
GPIO
J1_03
P4.2
GPIO/CMOD
J1_04
P4.3
GPIO/CTANK
J1_05
P0.0
GPIO
J1_06
P0.1
GPIO
J1_07
P0.2
GPIO
J1_08
P0.3
GPIO
J1_09
P0.4
GPIO
J1_10
P0.5
GPIO
J1_11
P0.6
GPIO
J1_12
P0.7
GPIO/SW1
J1_13
P1.0
GPIO
J1_14
P1.1
GPIO
J1_15
P1.2
GPIO
J1_16
P1.3
GPIO
J1_17
P1.4
GPIO
J1_18
P1.5
GPIO
J1_19
P1.6
GPIO/LED1
J1_20
P1.7
GPIO/SAR Bypass (EXT_VREF)
J1_21
GND
Ground
J1_22
VDD
Power
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
29
Hardware
Table 4-2. J2 Header Pin Details
PSoC 4 GPIO Header (J2)
Pin
4.3.3.2
Signal
Description
J2_01
VDD
Power
J2_02
GND
Ground
J2_03
RESET
Reset
J2_04
P3.3
GPIO/SWDCLK
J2_05
P3.2
GPIO/SWDIO
J2_06
P3.7
GPIO
J2_07
P3.6
GPIO
J2_08
P3.5
GPIO
J2_09
P3.4
GPIO
J2_10
P3.3
GPIO/SWDCLK
J2_11
P3.2
GPIO/SWDIO
J2_12
P3.1
GPIO
J2_13
P3.0
GPIO
J2_14
P2.7
GPIO
J2_15
P2.6
GPIO
J2_16
P2.5
GPIO
J2_17
P2.4
GPIO
J2_18
P2.3
GPIO
J2_19
P2.2
GPIO
J2_20
P2.1
GPIO
J2_21
P2.0
GPIO
J2_22
GND
Ground
Functionality of J3 and J5 Headers (PSoC 4 to USB-Serial)
Both the USB-Serial and the PSoC 4 prototyping boards each contain a 1×4-pin header. This header
provides a physical connection between the two devices. Specifically, the connection includes the
UART (RX and TX), VDD, and GND connections between the two devices. When the boards are
separated, this physical connection is broken.
Figure 4-5. J3 and J5 Headers
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
30
Hardware
Table 4-3. Pin Details of J3 Header
PSoC 4 to USB-Serial Header (J3)
Pin
Signal
Description
J3_01
VDD
Power
J3_02
GND
Ground
J3_03
P4.0
UART RX
J3_04
P4.1
UART TX
Table 4-4. Pin Details of J5 Header
USB-Serial to PSoC 4 Header (J5)
Pin
Signal
Description
J5_01
VDD
Power
J5_02
GND
Ground
J5_03
SCB.0/GPIO_6
UART TX
J5_04
SCB.4/GPIO_5
UART RX
Figure 4-6. UART Connection to PSoC 4
4.3.3.3
Functionality of J6 and J7 Headers (USB-Serial)
The USB-Serial board contains two dual-inline headers (J6 and J7). These headers are both 1x7-pin
headers and include all of the GPIO and SCB connections. These headers support all of the available ports, GND, VDD, and connections to passive elements and user-input devices.
The J6 and J7 headers support 100-mil spacing, so you can solder the male connectors to connect
the USB-Serial board to any development breadboard.
Figure 4-7. J6 and J7 Connectors
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
31
Hardware
Table 4-5. Pin Details of J6
USB-Serial Comm/GPIO Header (J6)
Pin
Signal
Description
J6_01
VDD
Power
J6_02
GND
Ground
J6_03
S SEL
Mode 0-6
J6_04
MISO/SCL
Mode 0-6
J6_05
MOSI/SDA
Mode 0-6
J6_06
SCLK
Mode 0-6
J6_07
SCB.5/GPIO_7
Mode 0-6
Table 4-6. Pin Details of J7
USB-Serial GPIO Header (J7)
Pin
Signal
Description
J7_01
GND
Power
J7_02
GPIO.0
Ground
J7_03
GPIO.1
Reset
J7_04
GPIO.8
GPIO
J7_05
GPIO.9
GPIO
J7_06
GPIO.10
GPIO
J7_07
GPIO.11
GPIO
4.3.4
User and Passive Inputs
4.3.4.1
Push Button
The main PSoC 4 board contains a single push button connected to the P0.7 pin on the PSoC 4
device. This button can be used for general user inputs and for triggering the bootloader for programming.
Figure 4-8. Push Button on the Board
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
32
Hardware
Figure 4-9. Push Button Schematic
4.3.4.2
CY8CKIT-049-4xxx LEDs
CY8CKIT-049-4xxx contains two LEDs: the amber LED, which indicates the board is power applied
and the blue LED that is directly connected to the PSoC 4 device through the pin P1.6. The blue LED
is also used to indicate the bootloader mode by rapidly blinking. The power LED is on the USB-Serial
board; if the boards are separated, the PSoC 4 section does not consume current through the power
LED.
Figure 4-10. Power LED
Figure 4-11. User LED
Figure 4-12. Power LED Connection
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
33
Hardware
Figure 4-13. User LED Connection
4.3.4.3
System Capacitors
The three capacitors on the CY8CKIT-049-4xxx prototyping kit enable proper development of ADC
and CapSense code examples. These capacitors are the following:
■
A SAR ADC bypass capacitor: Required for proper sampling at high frequencies,
■
Two CapSense capacitors (CMOD and CTANK): Required for proper CapSense functionality.
Figure 4-14. System Capacitors Circuit Diagram
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
34
5.
Code Examples
This section describes how to use the code example included with the kit and how to develop
custom bootloadable code examples for new applications.
For a list of all code examples available with PSoC Creator, visit the PSoC 3/4/5 Code Examples
page. This page lists all the PSoC Creator based code examples available across PSoC Creator,
Application notes and kits. Most of these examples CANNOT be directly used with the kit. Refer to
Converting a Non-bootloadable Project to a Bootloadable Project on page 40 for details on how to
port these projects to use with CY8CKIT-049.
For PSoC Creator related training and video tutorials, visit PSoC Creator training page.
5.1
Bootloader Base Code Example
The CY8CKIT-049-4xxx prototyping board is pre-programmed with a simple blinking LED code
example. This code example uses a PWM to slowly blink an LED. Included in the application project
is the Bootloader Base project. The Bootloader code is detailed in the UART_Bootloader project
available on the kit web page.
In the bootloader example, the device rapidly blinks an LED when the bootloader is active, provides
UART communication support for bootloading, and reads the state of the switch (SW1). You can
observe the state of the board by noticing the rate at which the LED blinks. The bootloader is activated when you plug in the CY8CKIT-049-4xxx while pressing the SW1 button. The bootloader
reads the state of this button during power-up. If the button is not pressed, the bootloader jumps to
the user's application code. If the button is pressed, then the bootloader waits for a new application
to be transferred. While the bootloader waits for the new application, it rapidly blinks the onboard
blue LED.
Note that the bootloader project is fully customizable, so you can use different methods for entering
the bootloader mode, and different feedback mechanisms. For example, you can change the project
so that it waits at power-up for a specified amount of time for a new application to be loaded rather
than through the use of a button press. All resources of the PSoC are available for use by the
bootloader project.
For details on UART bootloader in PSoC 4, please refer AN68272 - PSoC® 3, PSoC 4 and PSoC
5LP UART Bootloader. The landing page of the application note also includes a video providing an
overview of a UART bootloader.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
35
Code Examples
Figure 5-1. UART Bootloader
The Bootloader Base Project includes the source code in the main.c and the UART_Btld.c files,
which support bootloading the PSoC 4 device. The source code is available for reference, but is not
necessary to create bootloadable applications.
5.2
Bootloadable Code Example
The example in Programming a CY8CKIT-049-4xxx Project Using the Bootloader on page 18
showed how to bootload the application code for a blinking LED project into the device using the
USB-Serial controller.
In the bootloadable code example, the following components are used:
■
Bootloadable
■
PWM
■
Clock
■
Digital Output Pin
■
Digital Constants (logic HIGH/LOW)
■
Off-Chip Components (external resistor, LED, and Vss)
In this code example, the PWM component is used to drive an output on a pin connected to the user
LED. The bootloadable component is placed to ensure that your application code is correctly
mapped to the target PSoC 4 bootloader flash-space mapping.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
36
Code Examples
Figure 5-2. Bootloadable Blinking LED Project
5.3
Creating a New Bootloadable Project
To create a new bootloadable project, do the following:
1. On the Start Page of PSoC Creator, click Create New Project.
2. On the New Project window, select an PSoC 4100/PSoC 4200 Design.
3. Enter a name for the project and select a workspace. You can either add the new project to an
existing workspace or create a new one.
4. Set the device to the PSoC 4 device on your CY8CKIT-049-4xxx. For example, the
CY8CKIT-049-42XX kit requires the CY8C4245AXI-483 device.
5. Click the + button next to Advanced, set the Application Type as Bootloadable.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
37
Code Examples
6. Click OK.
Figure 5-3. Creating a New Bootloadable Project
PSoC Creator generates a new project.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
38
Code Examples
7. Navigate to the schematic view to place your components (double-click on the .cysch file from the
project in Workspace Explorer).
Select the Page 1 tab in the schematic if it is not already selected. The key component that must
be added is the Bootloadable component, which is used to generate the bootloadable application
code.
Figure 5-4. Bootloadable Project Schematic
8. Double-click the Bootloadable component to configure the selections.
The selections must be the same as those in the code example. Refer to Programming a
CY8CKIT-049-4xxx Project Using the Bootloader on page 18.
Figure 5-5. Configure Bootloadable Component
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
39
Code Examples
9. Click the Dependencies tab to select the HEX and ELF files from the UART Bootloader project
included with the kit.
You must always point your bootloadable project to a base bootloader project. The bootloader
project can be in the same workspace as your bootloadable project, but this is not necessary.
This code example uses the default application shipped with CY8CKIT-049-4xxx.
10.Click Apply and then click OK.
Figure 5-6. Specifying the References
11. After the project builds without errors, follow the steps shown in Programming a CY8CKIT-0494xxx Project Using the Bootloader on page 18 to bootload the new code into the target using the
Bootloader Host application.
This example does not have any source code, but is a base code example. Follow the steps in the
next examples to add functionality to this base project.
5.4
Converting a Non-bootloadable Project to a Bootloadable Project
As part of PSoC Creator application notes and kits available at www.cypress.com, Cypress provides
many code examples that you can work with. Most of these code examples do not include a bootloader in the project and are not directly usable with the CY8CKIT-049 kit. However, with a very
small modification to the project, they can be easily made to work with the CY8CKIT-049 kit. The following section describes how to port a code example that is not bootloadable into a bootloadable
example. We will take a simple PSoC Creator code example, PWMExample, for this purpose. You
can follow the same steps to port any non-bootloadable project to a bootloadable project.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
40
Code Examples
5.4.1
PWMExample
This example explains how to get the PWMExample project from the PSoC Creator code examples
list into your workspace and target the CY8CKIT-049-4xxx development kits.
1. In PSoC Creator, click Find Example Project… under Start Page > Examples and Kits.
Figure 5-7. Opening “Find Example Project” Window
2. Set the Device Family option to the kit family; select PSoC 4200 for the CY8CKIT-049-42xx kit
and PSoC 4100 for the CY8CKIT-049-41xx kit. The PSoC 4200 device family and
CY8CKIT-049-42xx are used in this example.
Figure 5-8. Selecting Device Family
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
41
Code Examples
3. You should now see all the examples supported by PSoC Creator for the selected family. In the
Project Name field, enter ‘PWMExample’. Select the PWMExample project from the list displayed and click Create New Workspace.
Figure 5-9. PWMExample Project Lookup
4. In the dialog box that appears, navigate to the folder location where you want to create the project.
5. After the workspace is created, PSoC Creator opens the help document detailing the project features and content. You can close this document and open it from the Workspace Explorer when
required.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
42
Code Examples
6. When the project opens in PSoC Creator, navigate to the Workspace Explorer window, right-click
on the project, and select Build Settings.
Figure 5-10. Accessing Build Settings
7. Because this project was originally set as a Normal Application Type, we need to change it to
Bootloadable. In the Application Type drop-down menu, select Bootloadable. Click Apply and
then OK.
Figure 5-11. Project Build Settings
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
43
Code Examples
8. Double-click the TopDesign.cysch file from the Workspace Explorer to open the schematic view.
Figure 5-12. Opening “TopDesign.cysch”
9. Drag and drop the Bootloadable component into the schematic window from the Component
Catalog under System.
Figure 5-13. Bootloadable Component in the Component Catalog
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
44
Code Examples
10.Double-click on the placed bootloadable component to configure the selections.
Figure 5-14. General Tab Parameters
11. Click the Dependencies tab to select the .hex and .elf files from the UART Bootloader project
included with the kit (\CY8CKIT-049-42xx\\Firmware\SCB_Bootloader\ UART_Bootloader.cydsn\CortexM0\ARM_GCC_484\Debug\). This is
done to point the bootloadable project to the bootloader running in the kit. Click Apply and then
OK.
Figure 5-15. Dependencies Tab Parameters
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
45
Code Examples
12.Because the project is not designed for the CY8CKIT-049 kit, you need to change the PWM output pin to the LED pin in CY8CKIT-049 (P1[6]). To do this, open PWMExample.cydwr from the
Workspace Explorer.
Figure 5-16. Opening “.cydwr” File
13.Select the LED_GREEN pin to P1[6] in the CY8CKIT-049 kit.
Figure 5-17. 'cydwr' Pin Settings
14.Select Build > Build PWMExample.
Figure 5-18. Building the Project
15.Connect the CY8CKIT-049-4xxx kit to the PC while pressing the SW1 button; this will put the
device into Bootloader mode. Entry into Bootloader mode is shown by the blinking LED.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
46
Code Examples
16.Open the Bootloader Host utility by selecting Tools > Bootloader Host from the PSoC Creator
menu. Connect to the COM port and make your port configurations.
Figure 5-19. Bootloader Host Tool
17.Click Filters…; configure it as shown in Figure 14 and then click OK.
Figure 5-20. Bootloader Host “Ports Filters” Settings
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
47
Code Examples
18.Click the Open File button and navigate to the project’s .cyacd file available at the following path:
\PWMExample01\PWMExample01.cydsn\CortexM0\ARM_GCC_484\Debug
Figure 5-21. Bootloader Host "cyacd" File Load Setting
19.Select the USB Serial Port (COMxx) corresponding to your kit and configure the settings, as
shown in Figure 5-22.
Figure 5-22. USB Serial Port Selection
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
48
Code Examples
20.Click the Program button. When the firmware is programmed, observe that the LED moves from
low intensity to higher intensity in steps of 100. You can change the BRIGHTNESS_DECREASE
macro to modify the step size.
Figure 5-23. Program Button in Bootloader Host
5.4.2
Entering Bootloader Mode from the Bootloadable Application
To program the PSoC 4 device on the CY8CKIT-049 kit, you need to enter the bootloader mode
through which you can load the desired application via the Bootloader Host utility and the USB-Serial
bridge. The default bootloader in the onboard PSoC 4 enters the bootloader mode when the SW1
button is pressed during board/device power up. This method of entering the bootloader can be time
consuming and you may not prefer removing the board from the PC each time you want to program
it. You can also enter the bootloader mode using the Bootloadable component present in the application project. When you want to enter bootloader mode, say when a button is pressed for a predefined duration or a command is sent via UART, all you need to do is detect the condition to enter
bootloader mode from the bootloadable application and call the “Bootloadable_Load()” API when the
condition is met. Let us use the example in PWMExample on page 41 and modify the project to enter
bootloader mode from the bootloadable application when SW1 is pressed for more than 2 seconds.
Follow these steps to modify the project in PWMExample on page 41 to enter bootloader mode from
the application.
1. Open TopDesign.cysch of the project; drag and drop a Digital Input Pin component into the
schematic view.
Figure 5-24. Digital Input Pin Component in Component Catalog
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
49
Code Examples
2. Double-click the placed component and configure the parameters as shown in Figure 5-25 and
click OK.
Figure 5-25. Digital Input Pin Parameter Configuration
3. In the PWMExample01.cydwr file, select P0[7] as the pin connection for SW1.
Figure 5-26. 'cydwr' Pin Settings
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
50
Code Examples
4. Open main.c file from the Workspace Explorer.
Figure 5-27. Opening main.c
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
51
Code Examples
5. Add the following code inside the infinite “for” loop. Note that you need to define a variable ‘uint8
swCounter’ in the beginning of the main loop.
for(;;)
{
/* Reset the software counter if SW1 is not pressed (Pulled high)
*/
if(SW1_Read())
{
swCounter = 0;
}
else
{
/* Increment the counter if SW1 is pressed (Shorted to GND) */
swCounter++;
}
/* Provide a 10 ms delay to make the counter approximately periodic every
10 ms */
CyDelay(10);
/* Check if the software counter has passed 2 s (200 * 10 ms)
==> Since the software counter is incremented only when SW1 is
==> pressed, SW1 is pressed for more than 2 seconds
==> Enter bootloader mode */
if(swCounter > 200)
{
Bootloadable_Load();
}
}
6. Build the project using Build > Build PWMExample01.
7. Program the PSoC 4 device as described from Step 15 in PWMExample on page 41.
8. When the new application is loaded, the output of the project will remain the same as in PWMExample on page 41. If you press and hold SW1 for 2 seconds without unplugging the device from
the PC, the device will enter bootloader mode (the LED will blink). To exit the bootloader mode,
unplug and re-plug the board from the USB port.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
52
6.
USB-Serial Configuration
The CY8CKIT-049-4xxx Prototyping Kits support the CY7C6521x family of USB controller products.
The CY7C6521x devices are a family of full-speed USB-Serial bridge controllers. These bridge controllers offer configurable serial channels for UART, I2C, SPI, or GPIO interfaces, with the industry's
lowest power consumption in the stand-by mode (5 µA).
USB-Serial bridge controllers integrate the CapSense capacitive-touch sensing technology and
USB-IF Battery Charging specification version 1.2. These controllers are ideal for applications such
as portable medical devices (such as blood-glucose meters), point-of-sales terminals, serial cables
(including USB-to-UART and RS-232 cables) and other applications requiring USB connectivity.
CY8CKIT-049-4xxx development kits use the USB-Serial device to provide connectivity to a PC and
to perform USB-UART bootload programming. The following sections provide instructions on how to
use and configure the USB-Serial device on the CY8CKIT-049-4xxx kits.
6.1
USB-Serial Resources
Use the following links to access a wide variety of content that includes custom software, utilities,
datasheets, and knowledge base articles.
■
USB-Serial landing page: www.cypress.com/go/usbserial
■
Software and drivers: USB-Serial Software Development Kit (SDK)
■
Datasheets: CY7C6521x Device Families
■
Additional information: Knowledge Base Articles
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
53
USB-Serial Configuration
6.2
USB-Serial Configuration Utility
Cypress USB-Serial Configuration Utility is an application included in the USB-Serial software development kit (SDK) installation. This utility is used to configure the USB-Serial device configuration,
and helps use additional capabilities of USB-Serial device such as USB-UART configurations, USBGPIO controls, and custom development using the USB-I2C and USB-SPI protocols.
After you install the USB-Serial SDK, click Start > All Programs > Cypress > Cypress
USB Serial > Cypress USB-Serial Configuration Utility to launch the USB-Serial Configuration
Utility.
Note: For Windows 8 or higher OS, launch Cypress USB-Serial Configuration Utility by doubleclicking on \USB-Serial SDK\\bin\USB Serial Configuration Utility.exe.
Figure 6-1. USB-Serial Configuration Utility
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
54
USB-Serial Configuration
6.2.1
Connecting to a USB-Serial Device
1. Connect the CY8CKIT-049-4xxx prototyping kit to the PC.
2. Open the USB-Serial Configuration Utility.
3. Select the Select Target tab.
Figure 6-2. Selecting the Target in USB-Serial Configuration Utility
The USB-Serial Configuration Utility will automatically detect that the USB-Serial Device has
been connected to the PC and will display the device in the Select Device drop-down menu.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
55
USB-Serial Configuration
4. Click Connect.
After connecting to the device, a new tab opens that displays the device marketing part number.
Figure 6-3. Selecting the Connected Device
5. Select the new tab and begin configuring the device.
6.2.2
Configuring a Serial Port
The USB-Serial device acts as a USB-UART bridge for the CY8CKIT-049-4xxx development kit. You
can use the Configuration Utility to read the default settings and configure new UART settings.
1. After connecting to the USB-Serial device, click the CY7C65211-24LTXI tab.
2. Select the SCB tab under the CY7C65211-24LTXI tab to see the default UART settings on the
USB-Serial device.
Figure 6-4. Configuring the Serial Port
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
56
USB-Serial Configuration
3. Click Configure next to the UART mode select.
The Configure UART Settings window appears, which displays the default settings for your
UART-Serial device.
Figure 6-5. Configuring UART Settings
4. Change the UART settings such as Baud Rate or Type by selecting the new values from the
respective drop-down lists, and click OK.
5. Click the Program Device button from the menu options at the top of the Configuration Utility to
program the device with the new settings.
Figure 6-6. Programming the Device With UART Settings
When the configuration has been programmed to the target device, a popup window will be
shown letting you know that programming was successful.
Note: Configurations will not be set immediately. You will need to reset the COM port for the
settings to be applied.
Figure 6-7. Confirmation for Device Programming
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
57
USB-Serial Configuration
6. To reset the device from the Configuration Utility, navigate to the Device menu and select Reset
Device. This initiates a reset to the device.
Figure 6-8. Resetting the Device
The utility will immediately detect that the device has been reconnected and display the Select
Target tab.
Figure 6-9. Device After Reconnection
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
58
USB-Serial Configuration
7. Connect to the device and navigate to the UART configuration window to see that the new configuration has been set. In this example, the Baud Rate is changed from 115200 to 9600.
Figure 6-10. Device UART Parameters Changed
6.2.3
Configuring GPIOs
The USB-Serial device included in the CY8CKIT-049-4xxx Prototyping Kit also supports GPIO controls through the J6 header. Each of the serial protocols requires a different number of GPIO pins.
Based on your serial configuration, the number of available GPIOs will change. The Configuration
Utility will only display the available GPIOs based on your serial configuration. For more information
on the serial configuration and the respective GPIO consumption, refer to the USB-Serial device
datasheet.
1. Plug CY8CKIT-049-4xxx into a USB port on the PC, and connect to the USB-Serial device using
the Configuration Utility.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
59
USB-Serial Configuration
2. Navigate to the CapSense/BCD/GPIO tab.
Figure 6-11. Device GPIO
3. Click Configure on the Unused GPIOs drive mode. This launches the GPIO configuration window.
This example shows how to change the output mode of the GPIO 08 pin to drive an output. You
can connect the pin to the PSoC 4, an LED, or any external circuitry.
4. Click the Select Drive Mode drop-down menu for the GPIO 08 pin.
Figure 6-12. Configuring GPIO Drive Mode
5. Select Drive 1 from the available options and click OK. This example makes the pin HIGH.
6. Program the new configuration into the device and cycle the port to see the new configuration
applied. For example, if the GPIO 08 pin is connected to an LED, you will see that the LED is on.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
60
USB-Serial Configuration
6.2.4
Additional Features of the USB-Serial Device
Apart from the UART and the GPIO features described in earlier sections, the USB-Serial device
included in the CY8CKIT-049-4xxx provides several other features, such as the following:
■
USB-I2C (Master/Slave)
■
USB-SPI (Master/Slave)
■
Cypress CapSense (up to eight buttons)
■
Battery Charging Detect (BCD)
For more information on these features, refer to the device datasheet and the USB-Serial Configuration Utility user guide. (Select Help > Help Topics).
Note: USB-UART works in the USB Communication Device Class (CDC), while all other configuration controls such as GPIO, SPI, and I2C use the Cypress vendor driver on the PC. Therefore, COM
port tools such as PuTTY or HyperTerminal will only work for the UART bridge. You can use the C++
APIs to create scripts and tools included with the USB-Serial SDK to evaluate and control the other
bridge options.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
61
A.
A.1
Appendix
CY8CKIT-049-4xxx Schematics
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
62
Appendix
Figure A-1. CY8C4245AXI-483 (CY8CKIT-049-42XX only)
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
63
Appendix
Figure A-2. CY8C4125AXI-483 (CY8CKIT-049-41XX only)
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
64
Appendix
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
65
Appendix
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
66
Appendix
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
67
Appendix
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
68
Appendix
A.2
Programming a CY8CKIT-049-4xxx Project Using MiniProg3
To use MiniProg3 for programming, connect wires or a 5-pin 100-mil spaced header to the
programming header on the CY8CKIT-049-4xxx board. The programming header is a 5-pin header
indicated on the silkscreen and is labeled ‘PROG’. The suggested part numbers are
Molex 22-05-3051 (right angled male header) and Molex 22-23-2051 (straight header). The
suggested part numbers for 5 pin headers are 5-pin Molex-KK right-angle male header
(Part number# 22-05-3051) or 5-pin Molex-KK vertical male header (Part number# 22-23-3051).
Please see images below for orientation of the header. The CY8CKIT-049 supports both power cycle
and reset programming modes.
Figure A-3. Connecting CY8CKIT-049-4xxx to MiniProg3 using right angled header
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
69
Appendix
Figure A-4. Connecting CY8CKIT-049-4xxx to MiniProg3 using straight header
Note: CY8CKIT-002 MiniProg3 is not part of the PSoC 4 Prototyping Kit contents and can be
purchased from the Cypress Online Store.
The following images show the pinout for MiniProg3 and the connections on CY8CKIT-049-4xxx.
Figure A-5. Pinout for MiniProg3
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
70
Appendix
Figure A-6. CY8CKIT-049-4xxx Connections for MiniProg3
The code examples described in this section show how to bootload new projects into PSoC 4 and
create bootloader and bootloadable projects. To access the kit examples, download the examples
from the kit web page.
The initial example shows how to program the kit with just a bootloader using MiniProg3. Note that
the kit is pre-programmed with a project containing a bootloader, so this step is not necessary to
change the application firmware.
1. Launch PSoC Creator from the Start menu.
Figure A-7. PSoC Creator Start Page
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
71
Appendix
2. Open the SCB_Bootloader.cywrk workspace by choosing File > Open > Project/Workspace
and navigating to the directory in which your project is present.
Figure A-8. Opening the Project in PSoC Creator
The workspace includes two sample projects linked in the Workspace Explorer - a bootloader
project and a bootloadable project.
3. Right-click the UART_Bootloader project and select Set As Active Project.
Figure A-9. Setting Code Example as Active Project in Workspace Explorer
4. Select Build > Build UART_Bootloader.
Figure A-10. Building the Project
5. Connect MiniProg3 to the CY8CKIT-049-4xxx prototyping board.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
72
Appendix
6. Select Debug > Program.
Figure A-11. Programming the CY8CKIT-049-4xxx
The Select Debug Target window opens.
Figure A-12. Debug Target Window
7. Click Port Settings, set the connector to 5 pin, and then click OK.
8. Click Port Acquire to detect the target device, click Connect, and then click OK.
PSoC Creator programs the target. When programming is complete, the PSoC 4 will contain the
bootloader but not any application code.
To bootload any application code, refer:
“Programming a CY8CKIT-049-4xxx Project Using the Bootloader” on page 18.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
73
Appendix
A.3
Bill of Materials
Table A-1. Bill of Materials
Item
Qty
Reference
Value
Description
Mfr Name
Mfr Part Number
PCB, 92.13mm x 24.13mm, High Tg,
ENIG finish, 2 layer, Color = RED, Silk =
WHITE
Cypress Semiconductors
600-60178-01
C1,C3,C5,C7,C8,
1.0 uF
C10
CAP CERAMIC 1.0UF 25V X5R 0603
10%
Taiyo Yuden
TMK107BJ105KA-T
1
C2
2200 pF
CAP CER 2200PF 50V 5% NP0 0805
Murata
GRM2165C1H222JA01D
4
4
C4,C6,C9,C12
0.1 uF
CAP .1UF 16V CERAMIC Y5V 0402
AVX Corporation
0402YG104ZAT2A
5
1
C11
10000 pF
CAP CER 10000PF 50V 5% NP0 0805
Murata
GRM2195C1H103JA01D
6
1
F1
FUSE
PTC Resettable Fuses 15Volts 100Amps
Bourns
MF-MSMF050-2
LED BLUE CLEAR 0805 SMD
Lite-On Inc
LTST-C170TBKT
1
1
N/A
2
6
3
N/A
7
1
LED1
Blue User
LED
8
1
LED2
Power LED
Amber
LED AMBER 591NM DIFF LENS 2012
Sharp Microelectronics
LT1ZV40A
9
4
R1, R2, R4, R6
ZERO
RES 0.0 OHM 1/8W 0805 SMD
Panasonic
ERJ-6GEY0R00V
ERJ-6GEYJ561V
10
2
R3, R5
560
RES 560 OHM 1/8W 5% 0805 SMD
Panasonic
11
2
R8, R9
ZERO
RES 0.0 OHM 1/10W 0603 SMD
Panasonic - ECG ERJ-3GEY0R00V
12
1
SW1
Switch
SWITCH TACTILE SPST-NO 0.05 A 32 V
C&K Components
44TQFP PSoC4A target chip
Cypress Semiconductor
KMR221GLFS
CY8C4245AXI-483 (4200
family)
13
1
U1
PSoC 4
14
1
U2
CY7C6521124QFN USB-Serial Bridge
24LTXI
Cypress Semiconductor
CY7C65211-24LTXI
Panasonic-ECG
ERJ-3GEYJ472V
CY8C4125AXI-483
(4100 family)
No Load Components
15
1
R7
4.7 K
RES 4.7K OHM 1/10W 5% 0603 SMD
16
1
N/A
N/A
LBL, PCA Label, Vendor Code, Datecode,
Cypress SemiSerial Number 121-60140-01 REV 01
conductor
(YYWWVVXXXXX)
17
1
N/A
N/A
LBL, PCBA Anti-Static Warning, 10mm X
10mm
Label
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
Cypress Semiconductor
74
Revision History
Document Revision History
Document Title: CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide
Document Number: 001-90711
Revision
ECN#
Issue Date
Origin of
Change
Description of Change
**
4270301
02/03/2014
RKAD
New kit guide.
*A
4312949
03/20/2014
RKAD
Updated Kit Operation chapter on page 16:
Updated “Programming a CY8CKIT-049-4xxx Project Using the
Bootloader” on page 18:
Replaced “Programming the CY8CKIT-049-4xxx Kit” with “Programming
a CY8CKIT-049-4xxx Project Using the Bootloader” in heading.
Updated description.
Removed “Programming a CY8CKIT-049-4xxx Project Using
MiniProg3”.
Removed sub-heading “Programming a CY8CKIT-049-4xxx Project
Using the Bootloader” only (as contents are coming under main
heading).
Updated Appendix chapter on page 62:
Added “Programming a CY8CKIT-049-4xxx Project Using MiniProg3” on
page 69.
*B
4416482
06/23/2014
RKAD
Updated “Title” in the file properties.
*C
4473817
10/09/2014
SASH
Replaced “USB Serial” with “USB-Serial” in all instances across the document.
Updated Introduction chapter on page 7:
Updated “Additional Learning Resources” on page 8:
Updated description.
Updated “Document Conventions” on page 12:
Replaced “PSoC Designer User Guide” with “PSoC Creator User
Guide”.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
75
Revision History
Document Revision History (continued)
Document Title: CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide
Document Number: 001-90711
Revision
ECN#
*C (cont.) 4473817
Issue Date
10/09/2014
Origin of
Change
SASH
Description of Change
Updated Software Installation chapter on page 13:
Renamed Chapter “Kit Installation” as “Software Installation”.
Removed “Kit Software”.
Added “Before You Begin” on page 13.
Added “CY8CKIT-049-41xx/CY8CKIT-049-42xx Software” on page 13.
Added “Install Software” on page 14.
Updated “Uninstall Software” on page 14:
Updated description.
Added “Uninstall USB-Serial Drivers” on page 15.
Updated “Open the “PSoC 4 Code” Code Example in PSoC Creator” on
page 15:
Updated description.
Updated Kit Operation chapter on page 16:
Updated “CY8CKIT-049-4xxx USB COM Port” on page 17:
Updated description.
Updated “Programming a CY8CKIT-049-4xxx Project Using the Bootloader” on page 18:
Updated description.
Updated Figure 3-7.
Updated Figure 3-11.
Updated Appendix chapter on page 62:
Updated “Programming a CY8CKIT-049-4xxx Project Using MiniProg3”
on page 69:
Updated description.
*D
4652397
02/05/2015
SASH
Updated Introduction chapter on page 7:
Updated “Additional Learning Resources” on page 8:
Updated description.
Added “PSoC Creator” on page 9.
Added “PSoC Creator Code Examples” on page 10.
Added “PSoC Creator Help” on page 11.
Added “Technical Support” on page 12.
Updated Software Installation chapter on page 13:
Updated “CY8CKIT-049-41xx/CY8CKIT-049-42xx Software” on
page 13:
Updated description.
Updated “Install Software” on page 14:
Updated description.
Updated “Open the “PSoC 4 Code” Code Example in PSoC Creator” on
page 15:
Updated description.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
76
Revision History
Document Revision History (continued)
Document Title: CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide
Document Number: 001-90711
Revision
ECN#
*D (cont.) 4652397
Issue Date
02/05/2015
Origin of
Change
SASH
Description of Change
Updated Kit Operation chapter on page 16:
Updated “CY8CKIT-049-4xxx USB COM Port” on page 17:
Updated description.
Updated “Programming a CY8CKIT-049-4xxx Project Using the Bootloader” on page 18:
Updated description.
Updated Figure 3-11.
Updated “USB-UART Default Settings” on page 25:
Updated description.
Updated Table 3-2 (Updated caption only).
Updated Code Examples chapter on page 35:
Updated “Creating a New Bootloadable Project” on page 37:
Updated description.
Updated Figure 5-3.
Updated Figure 5-4.
Updated Figure 5-6.
Removed “Adapting Projects from 100 Projects in 100 Days”.
Updated USB-Serial Configuration chapter on page 53:
Updated “USB-Serial Resources” on page 53:
Updated description.
Updated “USB-Serial Configuration Utility” on page 54:
Updated Figure 6-1.
Updated Appendix chapter on page 62:
Updated “Programming a CY8CKIT-049-4xxx Project Using MiniProg3”
on page 69:
Updated description.
Updated Figure A-3.
Added Figure A-4.
*E
4675832
03/02/2015
SASH
Updated Hardware chapter on page 26:
Updated “Functional Description” on page 27:
Updated “Header Connections” on page 28:
Updated “Functionality of J3 and J5 Headers (PSoC 4 to USB-Serial)”
on page 30:
Updated Table 4-4:
Updated details in “Pin” column.
Updated Figure 4-6.
Updated “Functionality of J6 and J7 Headers (USB-Serial)” on page 31:
Updated Table 4-5:
Updated details in “Pin” column.
Updated Table 4-6:
Updated details in “Pin” column.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
77
Revision History
Document Revision History (continued)
Document Title: CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide
Document Number: 001-90711
Revision
*F
ECN#
4690296
Issue Date
03/19/2015
Origin of
Change
SASH
Description of Change
Updated Introduction chapter on page 7:
Updated “Additional Learning Resources” on page 8:
Updated description.
Updated “Technical Support” on page 12:
Updated description.
Updated Software Installation chapter on page 13:
Updated “Install Software” on page 14:
Updated description.
Removed figure “The 'Cypress' icon”.
Removed figure “USB-Serial Driver Installation window”.
Removed figure “USB-Serial Driver installation - Finish page”.
Removed “Uninstall USB-Serial Drivers” on page 15.
Updated Code Examples chapter on page 35:
Updated description.
Updated “Bootloader Base Code Example” on page 35:
Updated description.
Updated “Bootloadable Code Example” on page 36:
Updated description.
Updated USB-Serial Configuration chapter on page 53:
Updated “USB-Serial Configuration Utility” on page 54:
Updated description.
*G
4716987
04/08/2015
MSUR
Updated Introduction chapter on page 7:
Updated “Additional Learning Resources” on page 8:
Updated description.
Updated Code Examples chapter on page 35:
Updated description.
Added “Converting a Non-bootloadable Project to a Bootloadable Project” on page 40.
*H
5612049
01/31/2017
RKAD
Updated to new template.
Completing Sunset Review.
*I
5739971
05/17/2017
AESATMP8 Updated logo and Copyright.
*J
6201368
06/08/2018
SRDS
Updated Kit Operation chapter on page 16:
Updated Figure 3-1.
CY8CKIT-049-4xxx PSoC® 4 Prototyping Kit Guide, Doc. #: 001-90711 Rev. *J
78
工商网监
湘ICP备2023018690号
