Please note that Cypress is an Infineon Technologies Company.
The document following this cover page is marked as “Cypress” document as this is the
company that originally developed the product. Please note that Infineon will continue
to offer the product to new and existing customers as part of the Infineon product
portfolio.
Continuity of document content
The fact that Infineon offers the following product as part of the Infineon product
portfolio does not lead to any changes to this document. Future revisions will occur
when appropriate, and any changes will be set out on the document history page.
Continuity of ordering part numbers
Infineon continues to support existing part numbers. Please continue to use the
ordering part numbers listed in the datasheet for ordering.
www.infineon.com
CYRS1542AV18
CYRS1544AV18
®
72-Mbit QDR II+ SRAM
Two-Word Burst Architecture
with RadStop™ Technology
72-Mbit QDR® II+ SRAM Two-Word Burst Architecture with RadStop™ Technology
Radiation Performance
■
JTAG 1149.1 compatible test access port
Radiation Data
■
DLL for accurate data placement
Configurations
■
Total Dose =300 Krad
■
Soft error rate (both Heavy Ion and proton)
Heavy ions 1 × 10-10 upsets/bit-day with an external SECDED
EDAC Controller
CYRS1542AV18 – 4M × 18
Neutrons = 2.0 × 1014 N/cm2
Functional Description
■
109 rad(Si)/sec
■
Dose rate = 2.0 ×
■
Dose rate survivability (rad(Si)/sec) = 1.5 × 10^11 rad(Si)/sec
■
Latch up immunity = 120 MeV.cm2/mg (125 °C)
Prototyping Options
CYRS1544AV18 – 2M × 36
The CYRS1542AV18 and CYRS1544AV18 are synchronous
pipelined SRAMs, equipped with 1.8-V QDR II+ architecture with
RadStop™ technology. Cypress’s state-of-the-art RadStop
Technology is radiation hardened through proprietary design and
process hardening techniques.
■
Separate independent read and write data ports
❐ Supports concurrent transactions
■
250-MHz clock for high bandwidth
■
Two-word burst on all accesses
■
Double data rate (DDR) interfaces on both read and write ports
at 250 MHz (data transferred at 500 MHz)
■
Two input clocks (K and K) for precise DDR timing
❐ SRAM uses rising edges only
The QDR II+ architecture consists of two separate ports to
access the memory: the read port and the write port. The read
port has dedicated data output bus to support read operations
and the write port has dedicated data input bus to support write
operations. QDR II+ architecture completely eliminates the need
to “turnaround” the data bus that exists with common I/O devices.
Each port is accessed through a common address bus.
Addresses for read are latched on the rising edges of the input
(K) clock whereas addresses for write are latched on the falling
edges of the input (K) clock. Accesses to the QDR II+ read and
write ports are completely independent of each another. To
maximize data throughput, both read and write ports are
equipped with DDR interfaces. Each address location is
associated with two 18-bit words for CYRS1542AV18, or two
36-bit words for CYRS1544AV18 that burst sequentially into or
out of the device. Since data can be transferred on every rising
edge of both input clocks (K and K#), memory bandwidth is
maximized while simplifying system design by eliminating bus
“turnarounds”.
■
Echo clocks (CQ and CQ) simplify data capture in high speed
systems
Depth expansion is accomplished with port selects, which
enables each port to operate independently.
■
Single multiplexed address input bus latches address inputs
for both read and write ports
■
Separate port selects for depth expansion
■
Synchronous internally self-timed writes
All synchronous inputs pass through input registers controlled by
the K or K input clocks. All data outputs pass through output
registers controlled by the K or K input clocks as well. Reads and
writes are conducted with on-chip synchronous self-timed
circuitry.
■
QDR® II operates with 2.0 cycle read latency when delay lock
loop (DLL) is enabled
For a complete list of related resources, click here.
■
Available in × 18 and × 36 configurations
Selection Guide
■
Full data coherency, providing most current data
■
Core VDD = 1.8 V (±0.1 V); I/O VDDQ = 1.4 V to VDD
Maximum operating frequency
■
Available in 165-ball CCGA (21 × 25 × 2.83 mm)
Maximum operating current
(concurrent R/W)
■
Non qualified CYPT1542AV18 and CTPT1544AV18 devices
with same functional and timing characteristics in a 165-ball
Ceramic Column Grid Array (CCGA) package and Land Grid
Array (LGA) package without solder columns attached.
Features
■
HSTL inputs and variable drive HSTL output buffers
Cypress Semiconductor Corporation
Document Number: 001-60006 Rev. *O
•
Description
198 Champion Court
•
250 MHz Unit
250
MHz
× 18
1700
mA
× 36
1700
San Jose, CA 95134-1709
•
408-943-2600
Revised May 27, 2019
CYRS1542AV18
CYRS1544AV18
Logic Block Diagram – CYRS1542AV18
K
CLK
Gen.
DOFF
21
Address
Register
Read Add. Decode
K
Write
Reg
2M x 18 Array
Address
Register
Write
Reg
2M x 18 Array
A(20:0)
21
18
Write Add. Decode
D[17:0]
A(20:0)
RPS
Control
Logic
Read Data Reg.
CQ
36
VREF
WPS
BWS[1:0]
18
Control
Logic
18
Reg.
Reg. 18
Reg.
18
CQ
18
Q[17:0]
QVLD
Logic Block Diagram – CYRS1544AV18
K
CLK
Gen.
DOFF
20
Address
Register
Read Add. Decode
K
Write
Reg
1M x 36 Array
Address
Register
Write
Reg
1M x 36 Array
A(19:0)
20
36
Write Add. Decode
D[35:0]
A(19:0)
RPS
Control
Logic
Read Data Reg.
CQ
72
VREF
WPS
BWS[3:0]
36
Control
Logic
36
Reg.
Reg. 36
Reg.
36
CQ
36
Q[35:0]
QVLD
Document Number: 001-60006 Rev. *O
Page 2 of 35
CYRS1542AV18
CYRS1544AV18
Contents
Manufacturing Flow .......................................................... 4
Radiation Hardened Design ........................................ 4
Neutron Soft Error Immunity ........................................... 4
Pin Configuration ............................................................. 5
Pin Definitions .................................................................. 6
Functional Overview ........................................................ 8
Read Operations ......................................................... 8
Write Operations ......................................................... 8
Byte Write Operations ................................................. 8
Concurrent Transactions ............................................. 8
Depth Expansion ......................................................... 8
Programmable Impedance .......................................... 8
Echo Clocks ................................................................ 9
Valid Data Indicator (QVLD) ........................................ 9
DLL .............................................................................. 9
Qualification and Screening ........................................ 9
Application Example ...................................................... 10
Truth Table ...................................................................... 11
Write Cycle Descriptions ............................................... 11
Write Cycle Descriptions ............................................... 12
IEEE 1149.1 Serial Boundary Scan (JTAG) .................. 13
Disabling the JTAG Feature ...................................... 13
Test Access Port ....................................................... 13
Performing a TAP Reset ........................................... 13
TAP Registers ........................................................... 13
TAP Instruction Set ................................................... 13
TAP Controller State Diagram ....................................... 15
TAP Controller Block Diagram ...................................... 16
TAP Electrical Characteristics ...................................... 16
TAP AC Switching Characteristics ............................... 17
TAP Timing and Test Conditions .................................. 18
Identification Register Definitions ................................ 19
Document Number: 001-60006 Rev. *O
Scan Register Sizes ....................................................... 19
Instruction Codes ........................................................... 19
Boundary Scan Order .................................................... 20
Power Up Sequence in QDR II+ SRAM ......................... 21
Power Up Sequence ................................................. 21
DLL Constraints ......................................................... 21
Maximum Ratings ........................................................... 22
Operating Range ............................................................. 22
Electrical Characteristics ............................................... 22
DC Electrical Characteristics ..................................... 22
AC Electrical Characteristics ..................................... 23
Radiation Performance .................................................. 23
Capacitance .................................................................... 23
Thermal Resistance ........................................................ 23
AC Test Loads and Waveforms ..................................... 24
Switching Characteristics .............................................. 25
Switching Waveforms .................................................... 26
Ordering Information ...................................................... 27
Ordering Code Definitions ......................................... 27
Package Diagrams .......................................................... 28
Acronyms ........................................................................ 30
Document Conventions ................................................. 30
Units of Measure ....................................................... 30
Glossary .......................................................................... 31
Document History Page ................................................. 32
Sales, Solutions, and Legal Information ...................... 35
Worldwide Sales and Design Support ....................... 35
Products .................................................................... 35
PSoC® Solutions ...................................................... 35
Cypress Developer Community ................................. 35
Technical Support ..................................................... 35
Page 3 of 35
CYRS1542AV18
CYRS1544AV18
Manufacturing Flow
Step
Screen
Method
Requirement
1
Wafer lot acceptance test
TM 5007
2
Internal visual
2010, Condition A
3
Serialization
4
Temperature cycling
1010, Condition C, 50 cycles minimum
100%
5
Constant acceleration
2001, YI orientation only
100%
7
Particle impact noise detection (PIND)
2020 Condition A
8
Radiographic (X-ray)
2012, one view (Y-1 orientation) only
9
Pre burn in electrical parameters
In accordance with applicable Cypress specification
100%
10
Dynamic burn in
1015, Condition D
100%
6
–
100%
100%
Condition TBD (package in design)
100%
240 hours at 125 °C or 120 hours at 150 °C minimum
11
Interim (post dynamic burn in) electricals
In accordance with applicable Cypress device specifications
100%
12
Static burn in
1015, Condition C, 72 hours at 150 °C or 144 hours at 125 °C
minimum
100%
13
Interim (post static burn in) electricals
In accordance with applicable Cypress device specifications
100%
14
Percent defective allowable (PDA) calculation 5% overall, 3% functional parameters at 25 °C
All lots
15
Final electrical test
100%
In accordance with applicable Cypress device specifications
a. Static tests
(1) 25 °C
5005, Table I, Subgroup 1
(2) –55 °C and +125 °C
5005, Table I, Subgroup 2, 3
b. Functional tests
(1) 25 C
5005, Table I, Subgroup 7
(2) –55 °C and +125 C
5005, Table I, Subgroup 8a, 8b
c. Switching test at 25 °C
5005, Table I, Subgroup 9
Seal (fine and gross leak test)
1014
17
External visual
2009
18
Wafer lot specific life test (Group C)
Mil-PRF 38535, Appendix B, section B.4.2.c
16
Radiation Hardened Design
The single event latch up (SEL) immunity is improved by a
radiation hardened design technique developed by Cypress
called RadStop. This design mitigation technique allows the SEL
performance to achieve radiation hard performance levels.
100%
100%
All wafer lots
Neutron Soft Error Immunity
Description
Test
Conditions
Typ
Max*
Unit
LSBU
Logical
single-bit
upsets
25 °C
320
368
FIT/
Mb
LMBU
Logical
multi-bit
upsets
25 °C
0
0.01
FIT/
Mb
Single event
latch up
125 °C
0
0.1
FIT/
Dev
Parameter
SEL
* No LMBU or SEL events occurred during testing; this column represents a
statistical 2, 95% confidence limit calculation. For more details refer to application
note AN54908 – Accelerated Neutron SER Testing and Calculation of Terrestrial
Failure Rates.
Document Number: 001-60006 Rev. *O
Page 4 of 35
CYRS1542AV18
CYRS1544AV18
Pin Configuration
Pin configurations for CYRS1542AV18 and CYRS1544AV18.[1]
Figure 1. 165-ball CCGA pinout
CYRS1542AV18 (4M × 18)
1
2
3
4
5
6
7
8
9
10
11
A
CQ
NC/144M
A
WPS
BWS1
K
NC/288M
RPS
A
A
CQ
B
NC
Q9
D9
A
NC
K
BWS0
A
NC
NC
Q8
C
NC
NC
D10
VSS
A
A
A
VSS
NC
Q7
D8
D
NC
D11
Q10
VSS
VSS
VSS
VSS
VSS
NC
NC
D7
E
NC
NC
Q11
VDDQ
VSS
VSS
VSS
VDDQ
NC
D6
Q6
F
NC
Q12
D12
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
Q5
G
NC
D13
Q13
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
D5
H
DOFF
VREF
VDDQ
VDDQ
VDD
VSS
VDD
VDDQ
VDDQ
VREF
ZQ
J
NC
NC
D14
VDDQ
VDD
VSS
VDD
VDDQ
NC
Q4
D4
K
NC
NC
Q14
VDDQ
VDD
VSS
VDD
VDDQ
NC
D3
Q3
L
NC
Q15
D15
VDDQ
VSS
VSS
VSS
VDDQ
NC
NC
Q2
M
NC
NC
D16
VSS
VSS
VSS
VSS
VSS
NC
Q1
D2
N
NC
D17
Q16
VSS
A
A
A
VSS
NC
NC
D1
P
NC
NC
Q17
A
A
QVLD
A
A
NC
D0
Q0
R
TDO
TCK
A
A
A
NC
A
A
A
TMS
TDI
9
10
11
CYRS1544AV18 (2M × 36)
1
2
3
4
5
6
7
8
A
CQ
B
Q27
NC/288M
A
WPS
BWS2
K
BWS1
RPS
A
NC/144M
CQ
Q18
D18
A
BWS3
K
BWS0
A
D17
Q17
Q8
C
D27
Q28
D19
VSS
A
A
A
VSS
D16
Q7
D8
D
D28
D20
Q19
VSS
VSS
VSS
VSS
VSS
Q16
D15
D7
E
Q29
D29
Q20
VDDQ
VSS
VSS
VSS
VDDQ
Q15
D6
Q6
F
Q30
Q21
D21
VDDQ
VDD
VSS
VDD
VDDQ
D14
Q14
Q5
G
D30
D22
Q22
VDDQ
VDD
VSS
VDD
VDDQ
Q13
D13
D5
H
DOFF
VREF
VDDQ
VDDQ
VDD
VSS
VDD
VDDQ
VDDQ
VREF
ZQ
J
D31
Q31
D23
VDDQ
VDD
VSS
VDD
VDDQ
D12
Q4
D4
K
Q32
D32
Q23
VDDQ
VDD
VSS
VDD
VDDQ
Q12
D3
Q3
L
Q33
Q24
D24
VDDQ
VSS
VSS
VSS
VDDQ
D11
Q11
Q2
M
D33
Q34
D25
VSS
VSS
VSS
VSS
VSS
D10
Q1
D2
N
D34
D26
Q25
VSS
A
A
A
VSS
Q10
D9
D1
P
Q35
D35
Q26
A
A
QVLD
A
A
Q9
D0
Q0
R
TDO
TCK
A
A
A
NC
A
A
A
TMS
TDI
Note
1. NC/144M and NC/288M are not connected to the die and can be tied to any voltage level.
Document Number: 001-60006 Rev. *O
Page 5 of 35
CYRS1542AV18
CYRS1544AV18
Pin Definitions
Pin Name
I/O
Pin Description
D[x:0]
InputData input signals. Sampled on the rising edge of K and K clocks during valid write operations.
Synchronous CYRS1542AV18 D[17:0]
CYRS1544AV18 D[35:0]
WPS
InputWrite port select Active LOW. Sampled on the rising edge of the K clock. When asserted active, a
Synchronous write operation is initiated. Deasserting deselects the write port. Deselecting the write port ignores D[x:0].
BWS0,
BWS1,
BWS2,
BWS3
InputByte write select (BWS) 0, 1, 2, and 3 Active LOW. Sampled on the rising edge of the K and K clocks
Synchronous during write operations. Used to select which byte is written into the device during the current portion of
the write operations. Bytes not written remain unaltered.
CYRS1542AV18 BWS0 controls D[8:0] and BWS1 controls D[17:9].
CYRS1544AV18 BWS0 controls D[8:0], BWS1 controls D[17:9], BWS2 controls D[26:18] and BWS3
controls D[35:27].
All the BWS are sampled on the same edge as the data. Deselecting a BWS ignores the corresponding
byte of data and it is not written into the device.
A[x:0]
InputAddress inputs. Sampled on the rising edge of the K (read address) and K (write address) clocks during
Synchronous active read and write operations. These address inputs are multiplexed for both read and write
operations. Internally, the device is organized as 4M × 18 (2 arrays each of 2M × 18) for CYRS1542AV18,
and 2M × 36 (2 arrays each of 1M × 36) for CYRS1544AV18. Therefore, only 21 address inputs are
needed to access the entire memory array of CYRS1542AV18, and 20 address inputs for
CYRS1544AV18. These inputs are ignored when the appropriate port is deselected.
Q[x:0]
OutputData output signals. These pins drive out the requested data during a read operation. Valid data is
Synchronous driven out on the rising edge of the K and K clock. When the read port is deselected, Q[x:0] are
automatically tristated.
CYRS1542AV18 Q[17:0]
CYRS1544AV18 Q[35:0]
RPS
InputRead port select Active LOW. Sampled on the rising edge of positive input clock (K). When active,
Synchronous a read operation is initiated. Deasserting deselects the read port. When deselected, the pending access
is allowed to complete and the output drivers are automatically tristated following the next rising edge of
the K clock. Each read access consists of a burst of four sequential transfers.
QVLD
Valid Output Valid output indicator. The Q Valid indicates valid output data. QVLD is edge aligned with CQ and CQ.
Indicator
K
Input Clock
Positive input clock input. The rising edge of K is used to capture synchronous inputs to the device
and to drive out data through Q[x:0] when in single clock mode. All accesses are initiated on the rising
edge of K.
K
Input Clock
Negative input clock input. K is used to capture synchronous inputs being presented to the device and
to drive out data through Q[x:0] when in single clock mode.
CQ
Echo Clock
Synchronous echo clock outputs. This is a free running clock and is synchronized to the input clock
K. The timing for the echo clocks is shown in Switching Characteristics on page 25.
CQ
Echo Clock
Synchronous echo clock outputs. This is a free running clock and is synchronized to the input clock
K. The timing for the echo clocks is shown in the Switching Characteristics on page 25.
ZQ
Input
Output impedance matching input. This input is used to tune the device outputs to the system data
bus impedance. CQ, CQ, and Q[x:0] output impedance are set to 0.2 × RQ, where RQ is a resistor
connected between ZQ and ground. Alternatively, connect this pin directly to VDDQ, which enables the
minimum impedance mode. This pin cannot be connected directly to GND or left unconnected.
DOFF
Input
DLL turn off Active LOW. Connecting this pin to ground turns off the DLL inside the device. The timing
in the operation with the DLL turned off differs from those listed in this data sheet. For normal operation,
connect this pin to a pull up through a 10 k or less pull up resistor. The device behaves in QDR I mode
when the DLL is turned off. In this mode, the device can be operated at a frequency of up to 167 MHz
with QDR I timing.
TDO
Output
Test data out (TDO) pin for JTAG.
Document Number: 001-60006 Rev. *O
Page 6 of 35
CYRS1542AV18
CYRS1544AV18
Pin Definitions (continued)
Pin Name
I/O
Pin Description
TCK
Input
Test clock (TCK) pin for JTAG.
TDI
Input
Test data in (TDI) pin for JTAG.
TMS
Input
Test mode select (TMS) pin for JTAG.
NC
N/A
Not connected to the die. Can be tied to any voltage level.
NC/144M
Input
Not connected to the die. Can be tied to any voltage level.
NC/288M
Input
Not connected to the die. Can be tied to any voltage level.
VREF
VDD
VSS
VDDQ
InputReference
Reference voltage input. Static input used to set the reference level for HSTL inputs, outputs, and AC
measurement points.
Power Supply Power supply inputs to the core of the device.
Ground
Ground for the device.
Power Supply Power supply inputs for the outputs of the device.
Document Number: 001-60006 Rev. *O
Page 7 of 35
CYRS1542AV18
CYRS1544AV18
Functional Overview
Write Operations
The CYRS1542AV18, and CYRS1544AV18 are synchronous
pipelined burst SRAMs with a read port and a write port. The read
port is dedicated to read operations and the write port is
dedicated to write operations. Data flows into the SRAM through
the write port and flows out through the read port. These devices
multiplex the address inputs to minimize the number of address
pins required. By having separate read and write ports, the
QDR II+ completely eliminates the need to turnaround the data
bus and avoids any possible data contention, thereby simplifying
system design. Each access consists of two 18-bit data transfers
in the case of CYRS1542AV18, and two 36-bit data transfers in
the case of CYRS1544AV18 in one clock cycle.
This device operates with a read latency of two cycles when
DOFF pin is tied HIGH. When DOFF pin is set LOW or connected
to VSS then the device behaves in QDR I mode with a read
latency of one clock cycle. DOFF is not a recommended mode
of operation.
Accesses for both ports are initiated on the rising edge of the
positive input clock (K). All synchronous input timing is
referenced from the rising edge of the input clocks (K and K) and
all output timing is referenced to the output clocks (K and K).
All synchronous data inputs (D[x:0]) pass through input registers
controlled by the input clocks (K and K). All synchronous data
outputs (Q[x:0]) pass through output registers controlled by the
rising edge of the output clocks (K and K).
All synchronous control (RPS, WPS, BWS[x:0]) inputs pass
through input registers controlled by the rising edge of the input
clocks (K and K).
CYRS1542AV18 is described below. The
descriptions also apply to CYRS1544AV18.
same
basic
Read Operations
The CYRS1542AV18 is organized internally as two arrays of
2M × 18. Accesses are completed in a burst of two sequential
18-bit data words. Read operations are initiated by asserting
RPS active at the rising edge of the positive input clock (K). The
address is latched on the rising edge of the K clock. The address
presented to the address inputs is stored in the read address
register. Following the next two K clock rising edges, the
corresponding lower order 18-bit word of data is driven onto the
Q[17:0] using K as the output timing reference. On the
subsequent rising edge of K, the next 18-bit data word is drive
onto the Q[17:0]. The requested data is valid 0.45 ns from the
rising edge of the output clock (K or K).
When the read port is deselected, the CYRS1542AV18 first
completes the pending read transactions. Synchronous internal
circuitry automatically tri-states the outputs following the next
rising edge of the positive input clock (K).
Document Number: 001-60006 Rev. *O
Write operations are initiated by asserting WPS active at the
rising edge of the positive input clock (K). On the same K clock
rise the data presented to D[17:0] is latched and stored into the
lower 18-bit write data register, provided BWS[1:0] are both
asserted active. On the subsequent rising edge of the negative
input clock (K), the address is latched in and the information
presented to D[17:0] is stored into the higher 18-bit write data
register, provided BWS[1:0] are both asserted active. The 36 bits
of data are then written into the memory array at the specified
location.
When deselected, the write port ignores all inputs after the
pending write operations are complete.
Byte Write Operations
Byte write operations are supported by the CYRS1542AV18. A
write operation is initiated as described in the Write Operations
section. The bytes that are written are determined by BWS0 and
BWS1, which are sampled with each set of 18-bit data words.
Asserting the appropriate BWS input during the data portion of a
write latches the data being presented and writes it into the
device. Deasserting the byte write select input during the data
portion of a write enables the data stored in the device for that
byte to remain unaltered. This feature can be used to simplify
read, modify, or write operations to a byte write operation.
Concurrent Transactions
The read and write ports on the CYRS1542AV18 operate
independently of one another. As each port latches the address
inputs on different clock edges, you can read or write to any
location, regardless of the transaction on the other port. You can
start reads and writes in the same clock cycle. If the ports access
the same location at the same time, the SRAM delivers the most
recent information associated with the specified address
location. This includes forwarding data from a write cycle that
was initiated on the previous K clock rise.
Depth Expansion
The CYRS1542AV18 has a port select input for each port. This
allows for easy depth expansion. Both port selects are sampled
on the rising edge of the positive input clock only (K). Each port
select input can deselect the specified port. Deselecting one port
does not affect the other port. All pending transactions (read and
write) are completed before the device is deselected.
Programmable Impedance
An external resistor, RQ, must be connected between the ZQ pin
on the SRAM and VSS to enable the SRAM to adjust its output
driver impedance. The value of RQ must be 5 × the value of the
intended line impedance driven by the SRAM. The allowable
range of RQ to guarantee impedance matching with a tolerance
of ±15% is between 175 and 350 , with VDDQ = 1.5 V. The
output impedance is adjusted every 1024 cycles upon power-up
to account for drifts in supply voltage and temperature.
Page 8 of 35
CYRS1542AV18
CYRS1544AV18
Echo Clocks
Qualification and Screening
Echo clocks are provided on the QDR II+ to simplify data capture
on high speed systems. Two echo clocks are generated by the
QDRII+. CQ is referenced with respect to K and CQb is
referenced with respect to K. These are free-running clocks and
are synchronized to the input clock of the QDR II+. The timing
for the echo clocks is shown in Switching Characteristics on page
25.
The 90-nm RadStop technology was qualified by Cypress after
meeting the criteria of the General Manufacturing Standards.
The test flow includes screening units with the defined flow
(Class Q, Class V) and the appropriate periodic or lot
conformance testing (Groups B, C, D, and E). Both the 90-nm
process and the SRAM products are subject to period or
lot-based technology conformance inspection (TCI) and quality
conformance inspection (QCI) tests, respectively. Cypress offers
both prototyping models and flight units of these product
configurations.
Valid Data Indicator (QVLD)
QVLD is provided on the QDR II+ to simplify data capture on high
speed systems. The QVLD is generated by the QDR II+ device
along with data output. This signal is also edge-aligned with the
echo clock and follows the timing of any data pin. This signal is
asserted half a cycle before valid data arrives.
Table 1. Qualification Tests
Groups
Tests
DLL
Group A
General electrical tests
These chips use a DLL that is designed to function between
120 MHz and the specified maximum clock frequency. During
power-up, when the DOFF is tied HIGH, the DLL is locked after
10240 cycles of stable clock. The DLL can also be reset by
slowing or stopping the input clocks K and K for a minimum of
30 ns. The DLL may be disabled by applying ground to the DOFF
pin. When the DLL is turned off, the device behaves in QDR I
mode (with one cycle latency and a longer access time). For
information refer to the application note AN5062, DLL
Considerations in QDRII/DDRII.
Group B
Mechanical - Dimensions,
bond strength, solvents, die
shear, solderability, lead
Integrity, seal, and
acceleration
Group C
Life tests - 1000 hours at
125 C or equivalent
Group D
Package related mechanical
tests - shock, vibration, accel,
salt, seal, lead finish adhesion,
lid torque, thermal shock, and
moisture resistance
Group E
Radiation tests
Document Number: 001-60006 Rev. *O
Page 9 of 35
CYRS1542AV18
CYRS1544AV18
Application Example
Figure 2 shows two QDR II+ used in an application.
Figure 2. Application Example
SRAM#1
D[x:0]
A
RPS
WPS
ZQ
CQ/CQ
Q[x:0]
BWS K K
RQ
SRAM#2
D[x:0]
A
RPS
WPS
ZQ
CQ/CQ
Q[x:0]
BWS K K
RQ
DATA IN[2x:0]
DATA OUT [2x:0]
ADDRESS
RPS
WPS
BWS
CLKIN1/CLKIN1
CLKIN2/CLKIN2
SOURCE K
SOURCE K
FPGA / ASIC
Document Number: 001-60006 Rev. *O
Page 10 of 35
CYRS1542AV18
CYRS1544AV18
Truth Table
CYRS1542AV18 and CYRS1544AV18 [2, 3, 4, 5, 6, 7]
Operation
K
RPS WPS
DQ
DQ
Write cycle:
Load address on the rising edge of K;
input write data on K and K rising edges.
L–H
X
L
D(A) at K(t)
D(A + 1) at K(t)
Read cycle:(2.0 cycle Latency)
Load address on the rising edge of K;
wait two cycles; read data on K and K rising edges.
L–H
L
X
Q(A) at K(t + 2)
Q(A + 1) at K(t + 2)
NOP: No operation
L–H
H
H
D=X
Q = High Z
D=X
Q = High Z
Stopped
X
X
Previous state
Previous state
Standby: Clock stopped
Write Cycle Descriptions
CYRS1542AV18 [2, 8]
BWS0
BWS1
K
K
L
L
L–H
–
L
L
–
L
H
L–H
L
H
–
H
L
L–H
H
L
–
H
H
L–H
H
H
–
Comments
During the data portion of a write sequence Both bytes (D[17:0]) are written into the device.
L–H During the data portion of a write sequence: Both bytes (D[17:0]) are written into the device.
–
During the data portion of a write sequence:
Only the lower byte (D[8:0]) is written into the device, D[17:9] remains unaltered.
L–H During the data portion of a write sequence
Only the lower byte (D[8:0]) is written into the device, D[17:9] remains unaltered.
–
During the data portion of a write sequence
Only the upper byte (D[17:9]) is written into the device, D[8:0] remains unaltered.
L–H During the data portion of a write sequence
Only the upper byte (D[17:9]) is written into the device, D[8:0] remains unaltered.
–
No data is written into the devices during this portion of a write operation.
L–H No data is written into the devices during this portion of a write operation.
Notes
2. X = “Don't Care,” H = Logic HIGH, L = Logic LOW, represents rising edge.
3. Device powers up deselected with the outputs in a tristate condition.
4. “A” represents address location latched by the devices when transaction was initiated. A + 0, A + 1 represents the internal address sequence in the burst.
5. “t” represents the cycle at which a Read/Write operation is started. t + 1, and t + 2 are the first, and second clock cycles respectively succeeding the “t” clock cycle.
6. Data inputs are registered at K and K rising edges. Data outputs are delivered on K and K rising edges.
7. It is recommended that K = K = HIGH when clock is stopped. This is not essential, but permits most rapid restart by overcoming transmission line charging symmetrically.
8. Is based on a write cycle that was initiated in accordance with the Truth Table. BWS0, BWS1, BWS2 and BWS2 can be altered on different portions of a write cycle, as
long as the setup and hold requirements are achieved.
Document Number: 001-60006 Rev. *O
Page 11 of 35
CYRS1542AV18
CYRS1544AV18
Write Cycle Descriptions
CYRS1544AV18 [9, 10]
BWS0
BWS1
BWS2
BWS3
K
K
Comments
L
L
L
L
L–H
–
During the data portion of a write sequence, all four bytes (D[35:0]) are written into
the device.
L
L
L
L
–
L
H
H
H
L–H
L
H
H
H
–
H
L
H
H
L–H
H
L
H
H
–
H
H
L
H
L–H
H
H
L
H
–
H
H
H
L
L–H
H
H
H
L
–
H
H
H
H
L–H
H
H
H
H
–
L–H During the data portion of a write sequence, all four bytes (D[35:0]) are written into
the device.
–
During the data portion of a write sequence, only the lower byte (D[8:0]) is written
into the device. D[35:9] remains unaltered.
L–H During the data portion of a write sequence, only the lower byte (D[8:0]) is written
into the device. D[35:9] remains unaltered.
–
During the data portion of a write sequence, only the byte (D[17:9]) is written into the
device. D[8:0] and D[35:18] remains unaltered.
L–H During the data portion of a write sequence, only the byte (D[17:9]) is written into the
device. D[8:0] and D[35:18] remains unaltered.
–
During the data portion of a write sequence, only the byte (D[26:18]) is written into
the device. D[17:0] and D[35:27] remains unaltered.
L–H During the data portion of a write sequence, only the byte (D[26:18]) is written into
the device. D[17:0] and D[35:27] remains unaltered.
–
During the data portion of a write sequence, only the byte (D[35:27]) is written into
the device. D[26:0] remains unaltered.
L–H During the data portion of a write sequence, only the byte (D[35:27]) is written into
the device. D[26:0] remains unaltered.
–
No data is written into the device during this portion of a write operation.
L–H No data is written into the device during this portion of a write operation.
Notes
9. X = “Don't Care,” H = Logic HIGH, L = Logic LOW, represents rising edge.
10. Is based on a write cycle that was initiated in accordance with the Truth Table on page 11. BWS0, BWS1, BWS2 and BWS2 can be altered on different portions of a
write cycle, as long as the setup and hold requirements are achieved
Document Number: 001-60006 Rev. *O
Page 12 of 35
CYRS1542AV18
CYRS1544AV18
IEEE 1149.1 Serial Boundary Scan (JTAG)
These SRAMs incorporate a serial boundary scan Test Access
Port (TAP) in the FBGA package. This part is fully compliant with
IEEE Standard #1149.1-2001. The TAP operates using JEDEC
standard 1.8 V I/O logic levels.
Disabling the JTAG Feature
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(VSS) to prevent clocking of the device. TDI and TMS are
internally pulled up and may be unconnected. They may
alternatively be connected to VDD through a pull up resistor. TDO
must be left unconnected. Upon power up, the device comes up
in a reset state, which does not interfere with the operation of the
device.
Test Access Port
Test Clock
The test clock is used only with the TAP controller. All inputs are
captured on the rising edge of TCK. All outputs are driven from
the falling edge of TCK.
Test Mode Select (TMS)
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. This pin may be left
unconnected if the TAP is not used. The pin is pulled up
internally, resulting in a logic HIGH level.
Test Data In (TDI)
The TDI pin is used to serially input information into the registers
and can be connected to the input of any of the registers. The
register between TDI and TDO is chosen by the instruction that
is loaded into the TAP instruction register. For information on
loading the instruction register, see the TAP Controller State
Diagram on page 15. TDI is internally pulled up and can be
unconnected if the TAP is unused in an application. TDI is
connected to the most significant bit (MSB) on any register.
Test Data Out (TDO)
The TDO output pin is used to serially clock data out from the
registers. The output is active, depending upon the current state
of the TAP state machine (see Instruction Codes on page 19).
The output changes on the falling edge of TCK. TDO is
connected to the least significant bit (LSB) of any register.
Performing a TAP Reset
A reset is performed by forcing TMS HIGH (VDD) for five rising
edges of TCK. This reset does not affect the operation of the
SRAM and can be performed while the SRAM is operating. At
power up, the TAP is reset internally to ensure that TDO comes
up in a high Z state.
TAP Registers
Registers are connected between the TDI and TDO pins to scan
the data in and out of the SRAM test circuitry. Only one register
can be selected at a time through the instruction registers. Data
is serially loaded into the TDI pin on the rising edge of TCK. Data
is output on the TDO pin on the falling edge of TCK.
Document Number: 001-60006 Rev. *O
Instruction Register
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the TDI
and TDO pins, as shown in TAP Controller Block Diagram on
page 16. At power up, the instruction register is loaded with the
IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state, as described
in the previous section.
When the TAP controller is in the Capture-IR state, the two least
significant bits are loaded with a binary “01” pattern to allow for
fault isolation of the board level serial test path.
Bypass Register
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between TDI
and TDO pins. This enables shifting of data through the SRAM
with minimal delay. The bypass register is set LOW (VSS) when
the BYPASS instruction is executed.
Boundary Scan Register
The boundary scan register is connected to all of the input and
output pins on the SRAM. Several no connect (NC) pins are also
included in the scan register to reserve pins for higher density
devices.
The boundary scan register is loaded with the contents of the
RAM input and output ring when the TAP controller is in the
Capture-DR state and is then placed between the TDI and TDO
pins when the controller is moved to the Shift-DR state. The
EXTEST, SAMPLE/PRELOAD, and SAMPLE Z instructions can
be used to capture the contents of the input and output ring.
The Boundary Scan Order on page 20 shows the order in which
the bits are connected. Each bit corresponds to one of the bumps
on the SRAM package. The MSB of the register is connected to
TDI, and the LSB is connected to TDO.
Identification (ID) Register
The ID register is loaded with a vendor specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired into
the SRAM and can be shifted out when the TAP controller is in
the Shift-DR state. The ID register has a vendor code and other
information described in Identification Register Definitions on
page 19.
TAP Instruction Set
Eight different instructions are possible with the three-bit
instruction register. All combinations are listed in Instruction
Codes on page 19. Three of these instructions are listed as
RESERVED and must not be used. The other five instructions
are described in this section in detail.
Instructions are loaded into the TAP controller during the Shift-IR
state when the instruction register is placed between TDI and
TDO. During this state, instructions are shifted through the
instruction register through the TDI and TDO pins. To execute
the instruction after it is shifted in, the TAP controller must be
moved into the Update-IR state.
Page 13 of 35
CYRS1542AV18
CYRS1544AV18
IDCODE
The IDCODE instruction loads a vendor specific, 32-bit code into
the instruction register. It also places the instruction register
between the TDI and TDO pins and shifts the IDCODE out of the
device when the TAP controller enters the Shift-DR state. The
IDCODE instruction is loaded into the instruction register at
power up or whenever the TAP controller is supplied a
Test-Logic-Reset state.
SAMPLE Z
The SAMPLE Z instruction connects the boundary scan register
between the TDI and TDO pins when the TAP controller is in a
Shift-DR state. The SAMPLE Z command puts the output bus
into a high Z state until the next command is supplied during the
Update IR state.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is an 1149.1 mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the input and output pins is captured
in the boundary scan register.
PRELOAD places an initial data pattern at the latched parallel
outputs of the boundary scan register cells before the selection
of another boundary scan test operation.
The shifting of data for the SAMPLE and PRELOAD phases can
occur concurrently when required, that is, while the data
captured is shifted out, the preloaded data can be shifted in.
BYPASS
When the BYPASS instruction is loaded in the instruction register
and the TAP is placed in a Shift-DR state, the bypass register is
placed between the TDI and TDO pins. The advantage of the
BYPASS instruction is that it shortens the boundary scan path
when multiple devices are connected together on a board.
EXTEST
The EXTEST instruction drives the preloaded data out through
the system output pins. This instruction also connects the
boundary scan register for serial access between the TDI and
TDO in the Shift-DR controller state.
EXTEST OUTPUT BUS TRISTATE
IEEE Standard 1149.1 mandates that the TAP controller be able
to put the output bus into a tristate mode.
You must be aware that the TAP controller clock only operates
at a frequency up to 20 MHz, while the SRAM clock operates
more than an order of magnitude faster. Because there is a large
difference in the clock frequencies, it is possible that during the
Capture-DR state, an input or output undergoes a transition. The
TAP may then try to capture a signal while in transition
(metastable state). This does not harm the device, but there is
no guarantee as to the value that is captured. Repeatable results
may not be possible.
The boundary scan register has a special bit located at bit #108.
When this scan cell, called the “extest output bus tristate,” is
latched into the preload register during the Update-DR state in
the TAP controller, it directly controls the state of the output
(Q-bus) pins, when the EXTEST is entered as the current
instruction. When HIGH, it enables the output buffers to drive the
output bus. When LOW, this bit places the output bus into a
high Z condition.
To guarantee that the boundary scan register captures the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller’s capture setup plus hold
times (tCS and tCH). The SRAM clock input might not be captured
correctly if there is no way in a design to stop (or slow) the clock
during a SAMPLE/PRELOAD instruction. If this is an issue, it is
still possible to capture all other signals and simply ignore the
value of the K and K captured in the boundary scan register.
This bit can be set by entering the SAMPLE/PRELOAD or
EXTEST command, and then shifting the desired bit into that cell,
during the Shift-DR state. During Update-DR, the value loaded
into that shift-register cell latches into the preload register. When
the EXTEST instruction is entered, this bit directly controls the
output Q-bus pins. Note that this bit is preset LOW to enable the
output when the device is powered up, and also when the TAP
controller is in the Test Logic Reset state.
After the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the boundary
scan register between the TDI and TDO pins.
Reserved
Document Number: 001-60006 Rev. *O
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
Page 14 of 35
CYRS1542AV18
CYRS1544AV18
TAP Controller State Diagram
The state diagram for the TAP controller follows. [11]
1
TEST-LOGIC
RESET
0
0
TEST-LOGIC/
IDLE
1
SELECT
DR-SCAN
1
1
SELECT
IR-SCAN
0
0
1
1
CAPTURE-DR
CAPTURE-IR
0
0
SHIFT-DR
0
SHIFT-IR
1
1
EXIT1-DR
1
EXIT1-IR
0
0
PAUSE-IR
1
0
1
EXIT2-DR
0
EXIT2-IR
1
1
UPDATE-IR
UPDATE-DR
1
1
0
PAUSE-DR
0
0
0
1
0
Note
11. The 0/1 next to each state represents the value at TMS at the rising edge of TCK.
Document Number: 001-60006 Rev. *O
Page 15 of 35
CYRS1542AV18
CYRS1544AV18
TAP Controller Block Diagram
0
Bypass Register
2
Selection
Circuitry
TDI
1
0
Selection
Circuitry
Instruction Register
31
30
29
.
.
2
1
0
1
0
TDO
Identification Register
108
.
.
.
.
2
Boundary Scan Register
TCK
TAP Controller
TMS
TAP Electrical Characteristics
Over the Operating Range
Parameter [12, 13, 14]
Description
Test Conditions
Min
Max
Unit
VOH1
Output high voltage
IOH =2.0 mA
1.4
–
V
VOH2
Output high voltage
IOH =100 A
1.6
–
V
VOL1
Output low voltage
IOL = 2.0 mA
–
0.4
V
VOL2
Output low voltage
IOL = 100 A
–
0.2
V
VIH
Input high voltage
VIL
Input low voltage
IX
Input and output load current
0.65 × VDD VDD + 0.3
GND VI VDD
V
–0.3
0.35 × VDD
V
–5
5
A
Notes
12. These characteristics pertain to the TAP inputs (TMS, TCK, TDI and TDO). Parallel load levels are specified in Electrical Characteristics on page 22.
13. Overshoot: VIH(AC) < VDDQ + 0.85 V (Pulse width less than tCYC/2), Undershoot: VIL(AC) > 1.5 V (Pulse width less than tCYC/2).
14. All Voltage referenced to ground.
Document Number: 001-60006 Rev. *O
Page 16 of 35
CYRS1542AV18
CYRS1544AV18
TAP AC Switching Characteristics
Over the Operating Range
Parameter [15, 16]
Description
Min
Max
Unit
50
–
ns
tTCYC
TCK clock cycle time
tTF
TCK clock frequency
–
20
MHz
tTH
TCK clock HIGH
20
–
ns
tTL
TCK clock LOW
20
–
ns
tTMSS
TMS setup to TCK clock rise
5
–
ns
tTDIS
TDI setup to TCK clock rise
5
–
ns
tCS
Capture setup to TCK rise
5
–
ns
tTMSH
TMS hold after TCK clock rise
5
–
ns
tTDIH
TDI hold after clock rise
5
–
ns
tCH
Capture hold after clock rise
5
–
ns
tTDOV
TCK clock LOW to TDO valid
–
10
ns
tTDOX
TCK clock LOW to TDO invalid
0
–
ns
Setup Times
Hold Times
Output Times
Notes
15. tCS and tCH refer to the setup and hold time requirements of latching data from the boundary scan register.
16. Test conditions are specified using the load in TAP AC Test Conditions. tR/tF = 1 ns.
Document Number: 001-60006 Rev. *O
Page 17 of 35
CYRS1542AV18
CYRS1544AV18
TAP Timing and Test Conditions
Figure 3 shows the TAP timing and test conditions. [17]
Figure 3. TAP Timing and Test Conditions
0.9 V
ALL INPUT PULSES
1.8 V
0.9 V
50
TDO
0V
Z0 = 50
(a)
CL = 20 pF
tTH
GND
tTL
Test Clock
TCK
tTMSH
tTMSS
tTCYC
Test Mode Select
TMS
tTDIS
tTDIH
Test Data In
TDI
Test Data Out
TDO
tTDOV
tTDOX
Note
17. Test conditions are specified using the load in TAP AC Test Conditions. tR/tF = 1 ns.
Document Number: 001-60006 Rev. *O
Page 18 of 35
CYRS1542AV18
CYRS1544AV18
Identification Register Definitions
Value
Instruction Field
CYRS1542AV18
Revision number (31:29)
000
000
Cypress device ID (28:12)
11010010100010100
11010010100100100
Cypress JEDEC ID (11:1)
00000110100
00000110100
1
1
ID register presence (0)
Description
CYRS1544AV18
Version number.
Defines the type of SRAM.
Allows unique identification of
SRAM vendor.
Indicates the presence of an ID
register.
Scan Register Sizes
Register Name
Bit Size
Instruction
3
Bypass
1
ID
32
Boundary Scan
109
Instruction Codes
Instruction
Code
Description
EXTEST
000
Captures the input and output ring contents.
IDCODE
001
Loads the ID register with the vendor ID code and places the register between TDI and TDO.
This operation does not affect SRAM operation.
SAMPLE Z
010
Captures the input and output contents. Places the boundary scan register between TDI and
TDO. Forces all SRAM output drivers to a high Z state.
RESERVED
011
Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD
100
Captures the input and output contents. Places the boundary scan register between TDI and
TDO. Does not affect the SRAM operation.
RESERVED
101
Do Not Use: This instruction is reserved for future use.
RESERVED
110
Do Not Use: This instruction is reserved for future use.
BYPASS
111
Places the bypass register between TDI and TDO. This operation does not affect SRAM
operation.
Document Number: 001-60006 Rev. *O
Page 19 of 35
CYRS1542AV18
CYRS1544AV18
Boundary Scan Order
Bit #
Bump ID
Bit #
Bump ID
Bit #
Bump ID
Bit #
Bump ID
0
6R
28
10G
56
6A
84
1J
1
6P
29
9G
57
5B
85
2J
2
6N
30
11F
58
5A
86
3K
3
7P
31
11G
59
4A
87
3J
4
7N
32
9F
60
5C
88
2K
5
7R
33
10F
61
4B
89
1K
6
8R
34
11E
62
3A
90
2L
7
8P
35
10E
63
2A
91
3L
8
9R
36
10D
64
1A
92
1M
9
11P
37
9E
65
2B
93
1L
10
10P
38
10C
66
3B
94
3N
11
10N
39
11D
67
1C
95
3M
12
9P
40
9C
68
1B
96
1N
13
10M
41
9D
69
3D
97
2M
14
11N
42
11B
70
3C
98
3P
15
9M
43
11C
71
1D
99
2N
16
9N
44
9B
72
2C
100
2P
17
11L
45
10B
73
3E
101
1P
18
11M
46
11A
74
2D
102
3R
19
9L
47
10A
75
2E
103
4R
20
10L
48
9A
76
1E
104
4P
21
11K
49
8B
77
2F
105
5P
22
10K
50
7C
78
3F
106
5N
23
9J
51
6C
79
1G
107
5R
24
9K
52
8A
80
1F
108
Internal
25
10J
53
7A
81
3G
26
11J
54
7B
82
2G
27
11H
55
6B
83
1H
Document Number: 001-60006 Rev. *O
Page 20 of 35
CYRS1542AV18
CYRS1544AV18
Power Up Sequence in QDR II+ SRAM
DLL Constraints
QDR II+ SRAMs must be powered up and initialized in a
predefined manner to prevent undefined operations.
■
DLL uses K clock as its synchronizing input. The input must
have low phase jitter, which is specified as tKC Var.
■
The DLL functions at frequencies down to 120 MHz.
■
If the input clock is unstable and the DLL is enabled, then the
DLL may lock onto an incorrect frequency, causing unstable
SRAM behavior. To avoid this, provide 10240 cycles stable
clock to relock to the desired clock frequency.
Power Up Sequence
■
Apply power and drive DOFF either HIGH or LOW (All other
inputs can be HIGH or LOW).
❐ Apply VDD before VDDQ.
❐ Apply VDDQ before VREF or at the same time as VREF.
❐ Drive DOFF HIGH.
■
Provide stable DOFF (HIGH), power and clock (K, K) for 10240
cycles to lock the DLL.
~
~
Figure 4. Power Up Waveforms
K
~
~
K
Unstable Clock
> 10240 Stable Clock
Start Normal
Operation
Clock Start (Clock Starts after VDD/VDDQ is Stable)
VDD/VDDQ
DOFF
Document Number: 001-60006 Rev. *O
VDD/VDDQ Stable (< + 0.1V DC per 50 ns)
Fix HIGH (tie to VDDQ)
Page 21 of 35
CYRS1542AV18
CYRS1544AV18
DC input voltage [18] ........................... –0.5 V to VDD + 0.5 V
Maximum Ratings
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Storage temperature ................................ –65 °C to +150 °C
Case temperature under power ............... –55 °C to +125 °C
Junction temperature under power ........... –55 °C to +150°C
Current into outputs (LOW) ........................................ 20 mA
Static discharge voltage
(MIL-STD-883, TM. 3015) ...................................... > 2001 V
Latch-up current .................................................... > 200 mA
Operating Range
Supply voltage on VDD relative to GND .......–0.5 V to +2.9 V
Supply voltage on VDDQ relative to GND ...... –0.5 V to +VDD
DC applied to outputs in high Z ........ –0.5 V to VDDQ + 0.5 V
Range
Military
Case Temperature
(Tc)
VDD[19]
VDDQ[19]
–55 °C to +125 °C
1.8 ± 0.1 V
1.4 V to VDD
Electrical Characteristics
Over the Operating Range
DC Electrical Characteristics
Over the Operating Range
Parameter [20]
Min
Typ
Max
Unit
VDD
Power supply voltage
1.7
1.8
1.9
V
VDDQ
I/O supply voltage
1.4
1.5
VDD
V
VOH
Output high voltage
Note 21
VDDQ/2 – 0.12
–
VDDQ/2 + 0.12
V
VOL
Output low voltage
Note 22
VDDQ/2 – 0.12
–
VDDQ/2 + 0.12
V
VOH(LOW)
Output high voltage
IOH =0.1 mA, nominal impedance
VDDQ – 0.2
–
VDDQ
V
VOL(LOW)
Output low voltage
IOL = 0.1 mA, nominal impedance
VSS
–
0.2
V
VIH
Input high voltage
VREF + 0.1
–
VDDQ + 0.3
V
VIL
Input low voltage
IX
Input leakage current
IOZ
Output leakage current
VREF
IDD
[24]
ISB1
Description
Input reference voltage
VDD operating supply
Automatic power down
current
Test Conditions
[23]
–0.3
–
VREF – 0.1
V
GND VI VDDQ
20
–
20
A
GND VI VDDQ, output disabled
20
–
20
A
Typical value = 0.75 V
0.68
0.75
0.95
V
mA
VDD = Max,
IOUT = 0 mA,
TJ=125 °C,
f = fMAX = 1/tCYC
250 MHz (× 18)
–
–
1700
(× 36)
–
–
1700
Max VDD,
Both ports deselected,
VIN VIH or VIN VIL,
f = fMAX = 1/tCYC,
TJ = 125 °C,
Inputs static
250 MHz (× 18)
–
–
660
(× 36)
–
–
660
mA
Notes
18. Overshoot: VIH(AC) < VDDQ + 0.85 V (Pulse width less than tCYC/2), Undershoot: VIL(AC) > 1.5 V (Pulse width less than tCYC/2).
19. Power up: Assumes a linear ramp from 0 V to VDD(min) within 200 ms. During this time VIH < VDD and VDDQ < VDD.
20. All Voltage referenced to ground.
21. Output are impedance controlled. IOH = (VDDQ/2)/(RQ/5) for values of 175 < RQ < 350 .
22. Output are impedance controlled. IOL = (VDDQ/2)/(RQ/5) for values of 175 < RQ < 350 .
23. VREF(min) = 0.68 V or 0.46 VDDQ, whichever is larger, VREF(max) = 0.95 V or 0.54 VDDQ, whichever is smaller.
24. The operation current is calculated with concurrent read and write cycles.
Document Number: 001-60006 Rev. *O
Page 22 of 35
CYRS1542AV18
CYRS1544AV18
AC Electrical Characteristics
Over the Operating Range
Parameter [25, 26]
Description
Test Conditions
Min
Typ
Max
Unit
VIH
Input high voltage
VREF + 0.2
–
–
V
VIL
Input low voltage
–
–
VREF – 0.2
V
Radiation Performance
Parameter
Test Conditions
Total dose
TA = 25 °C, VDD = VDDQ = 1.8 V
Soft error rate
TA = 25 °C to 125 °C, VDD = VDDQ = 1.8 V with EDAC
Transient dose
rate upset
Pulse width (FWHM) = 50 ns, X-Ray, TC = 25 °C, VDD = VDDQ = 1.8 V
Neutron fluence
1 MeV equivalent energy, Unbiased TA = 25 C
Latch up
immunity
TA = 125 °C, VDD = VDDQ = 1.9 V
Limits
Unit
300 Krad
Rads(Si) Co60
1.0 × 10^-10
Upsets/bit-day
2.0 × 109
Rads(Si)/s
2e14
N/cm2
110
MeVcm2/mg
Capacitance
Parameter [27]
Description
Test Conditions
TA = 25 °C, f = 1 MHz, VDD = 1.8 V, VDDQ = 1.5 V
Max
Unit
10
pF
CIN
Input capacitance
CCLK
Clock input capacitance
10
pF
CO
Output capacitance
10
pF
Thermal Resistance
Parameter [27]
JC
Description
Thermal resistance
(junction to case)
Test Conditions
Test conditions follow standard test methods and
procedures for measuring thermal impedance, in
accordance with EIA/JESD51.
165-ball CCGA Unit
Package
8.9
°C/W
Notes
25. Overshoot: VIH(AC) < VDDQ + 0.85 V (Pulse width less than tCYC/2), Undershoot: VIL(AC) > 1.5 V (Pulse width less than tCYC/2).
26. Power up: Assumes a linear ramp from 0 V to VDD(min) within 200 ms. During this time VIH < VDD and VDDQ < VDD.
27. Tested initially and after any design or process change that may affect these parameters.
Document Number: 001-60006 Rev. *O
Page 23 of 35
CYRS1542AV18
CYRS1544AV18
AC Test Loads and Waveforms
Figure 5. AC Test Loads and Waveforms
VREF = 0.75 V
VREF
0.75 V
VREF
OUTPUT
DEVICE
UNDER
TEST
ZQ
Z0 = 50
RL = 50
VREF = 0.75 V
R = 50
ALL INPUT PULSES
1.25 V
0.75 V
OUTPUT
DEVICE
UNDER
TEST ZQ
RQ =
250
(a)
0.75 V
INCLUDING
JIG AND
SCOPE
5 pF
[28]
0.25 V
SLEW RATE= 2 V/ns
RQ =
250
(b)
Note
28. Unless otherwise noted, test conditions are based on signal transition time of 2 V/ns, timing reference levels of 0.75 V, Vref = 0.75 V, RQ = 250 , VDDQ = 1.5 V, input
pulse levels of 0.25 V to 1.25 V, and output loading of the specified IOL/IOH and load capacitance shown in (a) of Figure 5.
Document Number: 001-60006 Rev. *O
Page 24 of 35
CYRS1542AV18
CYRS1544AV18
Switching Characteristics
Over the Operating Range
Parameters [29, 30]
250 MHz
Description
Cypress Consortium
Parameter Parameter
VDD(typical) to the first access [31]
tPOWER
Unit
Min
Max
1
–
ms
tCYC
tKHKH
K clock cycle time
4.0
8.4
ns
tKH
tKHKL
Input clock (K/K) HIGH
1.6
–
ns
tKL
tKLKH
Input clock (K/K) LOW
1.6
–
ns
tKHKH
tKHKH
K clock rise to K clock rise (rising edge to rising edge)
1.8
–
ns
0.5
–
ns
Setup Times
tSA
tAVKH
Address setup to K clock rise
tSC
tIVKH
Control setup to K clock rise (RPS, WPS)
0.5
–
ns
tSCDDR
tIVKH
DDR control setup to clock (K/K) rise (BWS0, BWS1, BWS2, BWS3)
0.5
–
ns
tSD
tDVKH
D[X:0] setup to clock (K/K) rise
0.5
–
ns
tHA
tKHAX
Address hold after K clock rise
0.5
–
ns
tHC
tKHIX
Control hold after K clock rise (RPS, WPS)
0.5
–
ns
tHCDDR
tKHIX
DDR control hold after clock (K/K) rise (BWS0, BWS1, BWS2, BWS3)
0.5
–
ns
tHD
tKHDX
D[X:0] hold after clock (K/K) rise
0.5
–
ns
–
0.85
ns
–0.85
–
ns
Hold Times
Output Times
tCO
tCHQV
K/K clock rise to data valid
tDOH
tCHQX
Data output hold after output K/K clock rise (Active to active)
tCCQO
tCHCQV
K/K clock rise to echo clock valid
tCQOH
tCHCQX
tCQD
–
0.85
ns
–
ns
tCQHQV
Echo clock hold after C/C clock rise
Echo clock high to data valid
–0.5
–
0.50
ns
tCQDOH
tCQHQX
Echo clock high to data invalid
–0.30
–
ns
tCQH
tCQHCQL
Output clock (CQ/CQ) HIGH [32]
1.55
–
ns
1.55
–
ns
–
0.45
ns
–0.45
–
ns
–0.5
0.5
ns
tCQHCQH
tCQHCQH
CQ clock rise to CQ clock rise (rising edge to rising edge)
tCHZ
tCHQZ
Clock (K/K) rise to high Z (active to high Z) [33, 34]
tCLZ
tQVLD
tCHQX1
Clock (K/K) rise to low Z
[33, 34]
[35]
[32]
tCQHQVLD
Echo Clock High to QVLD Valid
tKC Var
tKC Var
Clock phase jitter
–
0.20
ns
tKC lock
tKC lock
DLL lock time (K)
10240
–
Cycles
tKC Reset
tKC Reset
K static to DLL reset
30
–
ns
DLL Timing
Notes
29. Unless otherwise noted, test conditions are based on signal transition time of 2 V/ns, timing reference levels of 0.75 V, Vref = 0.75 V, RQ = 250 , VDDQ = 1.5 V,
input pulse levels of 0.25 V to 1.25 V, and output loading of the specified IOL/IOH and load capacitance shown in (a) of Figure 5 on page 24.
30. When a part with a maximum frequency above 167 MHz is operating at a lower clock frequency, it requires the input timings of the frequency range in which it is
being operated and outputs data with the output timings of that frequency range.
31. This part has a voltage regulator internally; tPOWER is the time that the power must be supplied above VDD(minimum) initially before initiating a read or write operation.
32. These parameters are extrapolated from the input timing parameters (tKHKH – 250 ps, where 250 ps is the internal jitter. An input jitter of 200 ps (tKC Var) is already
included in the tKHKH). These parameters are only guaranteed by design and are not tested in production.
33. tCHZ, tCLZ, are specified with a load capacitance of 5 pF as in part (b) of Figure 5 on page 24. Transition is measured 100 mV from steady state voltage.
34. At any voltage and temperature tCHZ is less than tCLZ and tCHZ less than tCO.
35. tQVLD Spec is applicable for both rising and falling edges of QVLD signal.
Document Number: 001-60006 Rev. *O
Page 25 of 35
CYRS1542AV18
CYRS1544AV18
Switching Waveforms
Figure 6. Read/Write/Deselect Sequence [36, 37, 38]
READ
1
WRITE
2
READ
3
READ
5
WRITE
4
NOP
7
WRITE
6
WRITE
8
NOP
9
10
11
12
K
tKH
tKHKH
tCYC
tKL
K
RPS
tSC tHC
WPS
A
D
A0
D10
A1
A2
tSA tHA
tSA tHA
D11
D30
A3
A4
A5
D31
D50
D51
A6
D60
D61
tSD tHD
tSD tHD
tQVLD
QVLD
tQVLD
Q
tCQD
tCO
tCLZ
Q00
tCHZ
tDOH
Q01
Q20
(Read Latency = 2.0 Cycles)
Q21
Q40
Q41
tCQDOH
tCCQO
CQ
tCQH
tCQHCQH
tCQOH
tCCQO
CQ
tCQOH
DON’T CARE
UNDEFINED
Notes
36. Q00 refers to output from address A0. Q01 refers to output from the next internal burst address following A0, that is, A0 + 1.
37. Outputs are disabled (high Z) one clock cycle after a NOP.
38. In this example, if address A0 = A1, then data Q00 = D10 and Q01 = D11. Write data is forwarded immediately as read results. This note applies to Figure 6.
Document Number: 001-60006 Rev. *O
Page 26 of 35
CYRS1542AV18
CYRS1544AV18
Ordering Information
The following table contains only the parts that are currently available. If you do not see what you are looking for (× 18 option), contact
your local sales representative. For more information, visit the Cypress website at www.cypress.com and refer to the product summary
page at http://www.cypress.com/products
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives and distributors. To find the office
closest to you, visit us at http://www.cypress.com/go/datasheet/offices.
Speed
(MHz)
Ordering Code
Package
Diagram
Description
Package Type
Operating
Range
250
CYRS1542AV18-250GCMB 72M QDR II+, × 18,
Burst of 2
001-58969 165-ball CCGA (21 × 25 × 2.83 mm)
Military
250
CYRS1544AV18-250GCMB 72M QDR II+, × 36,
Burst of 2
001-58969 165-ball CCGA (21 × 25 × 2.83 mm)
Military
250
CYPT1542AV18-250GCMB
72M QDR II+, × 18,
Burst of 2, Prototype
001-58969 165-ball CCGA (21 × 25 × 2.83 mm)
Military
250
CYPT1544AV18-250GCMB
72M QDR II+, × 36,
Burst of 2, Prototype
001-58969 165-ball CCGA (21 × 25 × 2.83 mm)
Military
250
CYPT1542AV18-250GLMB
72M QDR II+, × 18,
Burst of 2, Prototype
002-21565 165-ball CLGA w/o solder columns
(21 × 25 × 3.07 mm)
Military
250
CYPT1544AV18-250GLMB
72M QDR II+, × 36,
Burst of 2, Prototype
002-21565 165-ball CLGA w/o solder columns
(21 × 25 × 3.07 mm)
Military
250
5962F1120101VXA
72M QDR II+, × 18,
Burst of 2, DLAM Part
001-58969 165-ball CCGA (21 × 25 × 2.83 mm)
Military
250
5962F1120201VXA
72M QDR II+, × 36,
Burst of 2, DLAM Part
001-58969 165-ball CCGA (21 × 25 × 2.83 mm)
Military
Ordering Code Definitions
CY XX 154X A V18 - 250 XX M B
Burn-in
Thermal Rating: M = Military
Package Type: XX = GC or GL
GC = 165-ball CCGA; GL = 165-ball CLGA w/o columns
Speed Grade: 250 MHz
Core Voltage: 1.8 V
Die Revision
Part Number Identifier: Density, Organization, Burst
154X = 1542 or 1544
Marketing Code: XX = RS or PT
RS = RadStop; PT = Prototype
Company ID: CY = Cypress
Document Number: 001-60006 Rev. *O
Page 27 of 35
CYRS1542AV18
CYRS1544AV18
Package Diagrams
Figure 7. 165-ball Ceramic Column Grid Array (CCGA) (21 × 25 mm) Package Outline, 001-58969
001-58969 *E
Document Number: 001-60006 Rev. *O
Page 28 of 35
CYRS1542AV18
CYRS1544AV18
Package Diagrams (continued)
Figure 8. 165-ball Ceramic Land Grid Array (CLGA) (21 × 25 × 3.07 mm) Package Outline, 002-21565
SYMBOL
NOTES:
DIMENSIONS
MIN.
NOM.
MAX.
A
2.59
2.83
3.07
D
20.79
21.00
21.21
E
24.75
25.00
25.25
D1
12.70 BSC
E1
17.78 BSC
N
1. ALL DIMENSIONS ARE IN MILLIMETERS.
165
b
1.08
1.16
eD
1.27 BSC
eE
1.27 BSC
1.24
002-21565 **
Document Number: 001-60006 Rev. *O
Page 29 of 35
CYRS1542AV18
CYRS1544AV18
Acronyms
Acronym
Document Conventions
Description
Units of Measure
BWS
byte write select
CCGA
ceramic column grid array
°C
degree Celsius
DED
double error detection
Krad
kiloradian
DLL
delay lock loop
MHz
megahertz
DDR
double data rate
µA
microampere
DSCC
defense supply center columbus
µF
microfarad
EDAC
error detection and correction
µs
microsecond
HSTL
high speed transceiver logic
mA
milliampere
I/O
input/output
mm
millimeter
JTAG
Joint Test Action Group
ms
millisecond
LSB
least significant bit
mV
LSBU
logical single-bit upsets
N/cm
LMBU
logical multi-bit upsets
ns
nanosecond
MSB
most significant bit
nm
nanometer
PDA
percent defect allowable
ohm
PIND
particle impact noise detection
%
percent
PDA
percent defective allowable
pF
picofarad
QDR
quad data rate
ps
picosecond
RPS
read port select
Rads(Si)
SEC
single error correction
unit of absorbed radiation energy from ionizing
radiation per kg of material.
(1 rad(Si)) = 10 mGy = 10 – 2 J/kg
V
volt
W
watt
SEL
single event latch up
SRAM
static random access memory
TAP
test access port
TCK
test clock
TDI
test data in
TDO
test data out
TMS
test mode select
WPS
write port select
Document Number: 001-60006 Rev. *O
Symbol
Unit of Measure
millivolt
2
Neutron particles fluence per cm2 area
Page 30 of 35
CYRS1542AV18
CYRS1544AV18
Glossary
Total Dose
Permanent device damage due to ions over device life
Heavy Ion
Instantaneous device latch up due to single ion
LET
Linear energy transfer (measured in MeVcm2)
Krad
Unit of measurement to determine device life in radiation environments.
Neutron
Permanent device damage due to energetic neutrons or protons
Prompt Dose
Data loss of permanent device damage due to X-rays and gamma rays < 20 ns
165-ball Ceramic Column Grid
Array
Hermetic ceramic 165-column package. Columns attached by Six Sigma
RadStop Technology
Cypress's patented Rad Hard design methodology
DLAM
Defense Logistics Agency Land and Maritime
LSBU
Logical Single Bit Upset. Single bits in a single correction word are in error.
LMBU
Logical Multi Bit Upset. Multiple bits in a single correction word are in error
Group A
General electrical testing
Group B
Mechanical - Dimensions, bond strength, solvents, die shear, solderability, lead integrity,
seal, acceleration
Group C
Life test - 1000 hours at 125 °C
Group D
Package related mechanical tests - shock, vibration, Accel, salt, seal, lead finish
adhesion, lid torque, thermal shock, moisture resistance
Group E
Radiation testing
Document Number: 001-60006 Rev. *O
Page 31 of 35
CYRS1542AV18
CYRS1544AV18
Document History Page
Document Title: CYRS1542AV18/CYRS1544AV18, 72-Mbit QDR® II+ SRAM Two-Word Burst Architecture with RadStop™
Technology
Document Number: 001-60006
Rev.
ECN No.
Orig. of
Change
Submission
Date
Description of Change
**
2940931
HRP
05/31/2010
New data sheet.
*A
3016545
HRP
08/26/2010
Updated Switching Characteristics (Updated minimum and maximum values
for all parameters under “Setup Time”, “Hold Time”; and updated minimum and
maximum values for tCO parameter under “Output Time”).
Updated Ordering Information (Updated part numbers).
Updated Package Diagrams:
spec 001-58969 – Changed revision from ** to *A.
Added Units of Measure.
*B
3281455
HRP
06/13/2011
Changed status from Advance to Final.
Replaced 2048 with 10240 for DLL lockup cycles in all instances across the
document.
Updated Configurations (Fixed typo).
Updated Selection Guide.
Updated DC Electrical Characteristics (Updated maximum current limit values
for the parameters IDD and ISB1 based on device characterization).
Updated Radiation Performance (Updated limits of Radiation Data based on
RHA qualification).
Updated Thermal Resistance (Replaced TBD with values in “165-ball CCGA
Package” column).
Updated Switching Characteristics (Updated minimum and maximum timing
values for the parameters tco, tDOH, tCCQO, tCQOH based on device
characterization).
Updated Ordering Information (Updated part numbers).
Updated Package Diagrams:
spec 001-58969 – Changed revision from *A to *C.
Updated to new template.
Completing Sunset Review.
*C
3471321
HRP
12/21/2011
Updated Identification Register Definitions (Replaced the value of Cypress
device ID (28:12) from 11010011010010100 to 11010010100010100 for
CYRS1542AV18 and replaced the value of Cypress device ID (28:12) from
11010011010100100 to 11010010100100100 for CYRS1544AV18).
*D
3524961
HRP
02/14/2012
Updated Radiation Performance:
Updated Prototyping Options:
Updated description.
Updated Application Example:
Updated Figure 2.
Updated Truth Table:
Updated details corresponding to “Read Cycle”.
Updated Maximum Ratings:
Removed “Ambient temperature under power” and its corresponding details.
Added “Case temperature under power” and its corresponding details.
Updated details corresponding to “Junction temperature under power”.
Updated Operating Range:
Replaced “Junction Temperature (Tj)” with “Case Temperature (Tc)” in column
heading.
Updated Radiation Performance:
Updated details under “Limits” column corresponding to Transient dose rate
upset parameter.
Updated Capacitance:
Updated details in “Max” column corresponding to all parameters.
Document Number: 001-60006 Rev. *O
Page 32 of 35
CYRS1542AV18
CYRS1544AV18
Document History Page (continued)
Document Title: CYRS1542AV18/CYRS1544AV18, 72-Mbit QDR® II+ SRAM Two-Word Burst Architecture with RadStop™
Technology
Document Number: 001-60006
Rev.
ECN No.
Orig. of
Change
Submission
Date
Description of Change
*D (cont.)
3524961
HRP
02/14/2012
Updated Thermal Resistance:
Removed JA parameter and its corresponding details.
Changed value of JC parameter from 11 °C/W to 8.9 °C/W corresponding to
165-ball CCGA Package.
Updated Switching Characteristics:
Updated all values of all parameters corresponding to 200 MHz under “Setup
Times”.
Updated all values of tCQD and tQVLD parameters under “Output Times”.
Updated Ordering Information (Updated part numbers).
*E
3537277
HRP
02/29/2012
Updated Radiation Performance:
Updated Radiation Data:
Updated description.
Updated Ordering Information (Updated part numbers).
*F
3580538
HRP
04/12/2012
Updated Ordering Information (Updated part numbers).
*G
3617759
HRP
05/15/2012
Updated Radiation Performance:
Updated Prototyping Options:
Updated description.
Updated Ordering Information (Updated part numbers).
Updated Glossary.
Completing Sunset Review.
*H
3640834
HRP
06/08/2012
Updated Radiation Performance:
Updated Prototyping Options:
Updated description.
Updated Manufacturing Flow:
Replaced “Class V Flow” with “Manufacturing Flow” in heading.
Updated Glossary.
*I
3857750
HRP
01/04/2013
Updated Ordering Information (Updated part numbers).
*J
3900846
HRP
02/11/2013
Updated Neutron Soft Error Immunity (Changed value of Test Conditions of
SEL parameter from 85 °C to 125 °C).
Updated Pin Definitions (Changed Pin Name from A to A[x:0]).
Updated Functional Overview (Updated Qualification and Screening
(Replaced Class V with Class Q)).
*K
3934155
MISA
03/15/2013
Updated Selection Guide:
Changed Maximum operating current (concurrent R/W) corresponding to
“× 18” for 250 MHz frequency from 1650 mA to 1700 mA.
Changed Maximum operating current (concurrent R/W) corresponding to
“× 36” for 250 MHz frequency from 1650 mA to 1700 mA.
Updated Electrical Characteristics:
Updated DC Electrical Characteristics:
Changed maximum value of IDD parameter from 1650 mA to 1700 mA
corresponding to “× 18” and 250 MHz frequency.
Changed maximum value of IDD parameter from 1650 mA to 1700 mA
corresponding to “× 36” and 250 MHz frequency.
Changed maximum value of ISB1 parameter from 600 mA to 660 mA
corresponding to “× 18” and 250 MHz frequency.
Changed maximum value of ISB1 parameter from 550 mA to 660 mA
corresponding to “× 36” and 250 MHz frequency.
Removed 200 MHz frequency related information.
Document Number: 001-60006 Rev. *O
Page 33 of 35
CYRS1542AV18
CYRS1544AV18
Document History Page (continued)
Document Title: CYRS1542AV18/CYRS1544AV18, 72-Mbit QDR® II+ SRAM Two-Word Burst Architecture with RadStop™
Technology
Document Number: 001-60006
Rev.
ECN No.
Orig. of
Change
Submission
Date
Description of Change
*K (cont.)
3934155
MISA
03/15/2013
Updated Switching Characteristics:
Changed maximum value of tCO and tCHQV parameters from 0.7 ns to 0.85 ns.
Changed minimum value of tDOH and tCHQX parameters from –0.7 ns to
–0.85 ns.
Changed maximum value of tCCQO and tCHCQV parameters from 0.7 ns to
0.85 ns.
Changed minimum value of tCQOH and tCHCQX parameters from –0.7 ns to
–0.85 ns.
Removed 200 MHz frequency related information.
Updated Package Diagrams:
spec 001-58969 – Changed revision from *C to *D.
*L
4286754
MISA
02/21/2014
Updated Functional Overview:
Updated Qualification and Screening:
Replaced “Class Q” with “Class Q, Class V”.
Updated Ordering Information (Updated part numbers).
Updated to new template.
*M
4618500
PRIT
01/09/2015
Updated Radiation Performance:
Updated Radiation Data:
Updated 2nd bulleted point.
Updated Prototyping Options:
Updated 1st bulleted point.
Updated Functional Description:
Updated description.
Added “For a complete list of related resources, click here.” at the end.
Updated Pin Definitions:
Updated description of CQ and CQ pins.
Updated Functional Overview:
Updated description.
Updated Read Operations:
Updated description.
Updated Write Operations:
Updated description.
Updated Application Example:
Updated Figure 2.
*N
5956093
HRP
11/03/2017
Added 165-ball Ceramic Land Grid Array Package related information in all
instances across the document.
Updated Ordering Information:
Updated part numbers.
Updated Package Diagrams:
spec 001-58969 – Changed revision from *D to *E.
Added spec 002-21565 Rev. **.
Updated to new template.
Completing Sunset Review.
*O
6582348
HRP
05/27/2019
Updated to new template.
Document Number: 001-60006 Rev. *O
Page 34 of 35
CYRS1542AV18
CYRS1544AV18
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
PSoC® Solutions
Products
Arm® Cortex® Microcontrollers
Automotive
cypress.com/arm
cypress.com/automotive
Clocks & Buffers
Interface
cypress.com/clocks
cypress.com/interface
Internet of Things
Memory
cypress.com/iot
cypress.com/memory
Microcontrollers
cypress.com/mcu
PSoC
cypress.com/psoc
Power Management ICs
Cypress Developer Community
Community | Projects | Video | Blogs | Training | Components
Technical Support
cypress.com/support
cypress.com/pmic
Touch Sensing
cypress.com/touch
USB Controllers
Wireless Connectivity
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP | PSoC 6 MCU
cypress.com/usb
cypress.com/wireless
© Cypress Semiconductor Corporation, 2010–2019. This document is the property of Cypress Semiconductor Corporation and its subsidiaries (“Cypress”). This document, including any software or
firmware included or referenced in this document (“Software”), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress
reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property
rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants
you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce
the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or
indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress’s patents that are infringed by the Software (as provided by
Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the
Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No computing
device can be absolutely secure. Therefore, despite security measures implemented in Cypress hardware or software products, Cypress shall have no liability arising out of any security breach, such
as unauthorized access to or use of a Cypress product. CYPRESS DOES NOT REPRESENT, WARRANT, OR GUARANTEE THAT CYPRESS PRODUCTS, OR SYSTEMS CREATED USING
CYPRESS PRODUCTS, WILL BE FREE FROM CORRUPTION, ATTACK, VIRUSES, INTERFERENCE, HACKING, DATA LOSS OR THEFT, OR OTHER SECURITY INTRUSION (collectively, “Security
Breach”). Cypress disclaims any liability relating to any Security Breach, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from any Security Breach. In
addition, the products described in these materials may contain design defects or errors known as errata which may cause the product to deviate from published specifications. To the extent permitted
by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or
circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the
responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. “High-Risk Device”
means any device or system whose failure could cause personal injury, death, or property damage. Examples of High-Risk Devices are weapons, nuclear installations, surgical implants, and other
medical devices. “Critical Component” means any component of a High-Risk Device whose failure to perform can be reasonably expected to cause, directly or indirectly, the failure of the High-Risk
Device, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from any use of
a Cypress product as a Critical Component in a High-Risk Device. You shall indemnify and hold Cypress, its directors, officers, employees, agents, affiliates, distributors, and assigns harmless from
and against all claims, costs, damages, and expenses, arising out of any claim, including claims for product liability, personal injury or death, or property damage arising from any use of a Cypress
product as a Critical Component in a High-Risk Device. Cypress products are not intended or authorized for use as a Critical Component in any High-Risk Device except to the limited extent that (i)
Cypress’s published data sheet for the product explicitly states Cypress has qualified the product for use in a specific High-Risk Device, or (ii) Cypress has given you advance written authorization to
use the product as a Critical Component in the specific High-Risk Device and you have signed a separate indemnification agreement.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in
the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
Document Number: 001-60006 Rev. *O
Revised May 27, 2019
QDR RAMs and Quad Data Rate RAMs comprise a new family of products developed by Cypress, IDT, NEC, Renesas, and Samsung.
Page 35 of 35