0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
CYUSB3011-BZXC

CYUSB3011-BZXC

  • 厂商:

    CYPRESS(赛普拉斯)

  • 封装:

    TFBGA121

  • 描述:

    IC ARM9 USB3 CONTROLLER 121FBGA

  • 数据手册
  • 价格&库存
CYUSB3011-BZXC 数据手册
CYUSB301X, CYUSB201X E Z- US B FX3 SuperSpeed USB Controller Features • Universal serial bus (USB) integration - USB 3.2, Gen 1 and USB 2.0 peripherals compliant with USB 3.2 Specification Revision 1.0 (TID # 340800007) - 5-Gbps SuperSpeed PHY compliant with USB 3.2 Gen 1 - High-speed On-The-Go (HS-OTG) host and peripheral compliant with OTG Supplement Version 2.0 - Thirty-two physical endpoints • General programmable interface (GPIF™ II) - Programmable 100-MHz GPIF II enables connectivity to a wide range of external devices - 8-, 16-, 24-, and 32-bit data bus - Up to 16 configurable control signals • Fully accessible 32-bit CPU - ARM926EJ core with 200-MHz operation - 512-KB or 256-KB embedded SRAM • Additional connectivity to the following peripherals - SPI master at up to 33 MHz - UART support of up to 4 Mbps - I2C master controller at 1 MHz - I2S master (transmitter only) at sampling frequencies of 8 kHz, 16 kHz, 32 kHz, 44.1 kHz, 48 kHz, 96 kHz and 192 kHz • Selectable clock input frequencies - 19.2, 26, 38.4, and 52 MHz - 19.2-MHz crystal input support • Ultra low-power in core power-down mode - Less than 60 µA with VBATT on and 20 µA with VBATT off • Independent power domains for core and I/O - Core operation at 1.2 V - I2S, UART, and SPI operation at 1.8 to 3.3 V - I2C operation at 1.2 V to 3.3 V • Package options - 121-ball, 10- × 10-mm, 0.8-mm pitch Pb-free ball grid array (BGA) - See Table 24 for details on the seven FX3 variants • EZ-USB® software development kit (SDK) for code development of firmware and PC Applications - Includes RTOS Framework (using ThreadX Version 5) - Firmware examples covering all I/O modules - Visual Studio host examples using C++ and C# • SuperSpeed explorer board available for rapid prototyping - Several accessory boards also available: • Adapter boards for Xilinx/Altera FPGA development • Adapter board for video development • CPLD board for concept testing and initial development Datasheet www.infineon.com Please read the Important Notice and Warnings at the end of this document page 1 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Applications Applicat ions • Digital video camcorders • Digital still cameras • Printers • Scanners • Video capture cards • Test and measurement equipment • Surveillance cameras • Personal navigation devices • Medical imaging devices • Video IP phones • Portable media players • Industrial cameras • Data loggers • Data acquisition • High-performance human interface devices (gesture recognition) Functio nal de sc ript ion For a complete list of related documentation, click here. Errata: For information on silicon errata, see “Errata” on page 70. Details include trigger conditions, devices affected, and proposed workaround. Datasheet 2 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Logic block diagram Logi c blo ck diagram Datasheet 3 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller More information 1 More information Infineon provides a wealth of data at www.infineon.com to help you to select the right USB SuperSpeed device for your design, and to help you to quickly and effectively integrate the device into your design. • Overview: USB Portfolio, USB Roadmap • USB 3.0 Product Selectors: FX3, FX3S, CX3, HX3, SX3 • Application notes: Infineon offers a large number of USB application notes covering a broad range of topics, from basic to advanced level. Recommended application notes for getting started with FX3 are: - AN75705 - Getting Started with EZ-USB FX3 - AN76405 - EZ-USB FX3 Boot Options - AN70707 - EZ-USB FX3/FX3S/SX3 Hardware Design Guidelines and Schematic Checklist - AN65974 - Designing with the EZ-USB FX3 Slave FIFO Interface - AN75779 - How to Implement an Image Sensor Interface with EZ-USB FX3 in a USB Video Class (UVC) Framework - AN86947 - Optimizing USB 3.0 Throughput with EZ-USB FX3 - AN84868 - Configuring an FPGA over USB Using Cypress EZ-USB FX3 - AN68829 - Slave FIFO Interface for EZ-USB FX3: 5-Bit Address Mode - AN73609 - EZ-USB FX2LP/ FX3 Developing Bulk-Loop Example on Linux - AN77960 - Introduction to EZ-USB FX3 High-Speed USB Host Controller - AN76348 - Differences in Implementation of EZ-USB FX2LP and EZ-USB FX3 Applications - AN89661 - USB RAID 1 Disk Design Using EZ-USB FX3S • Code Examples: - USB Hi-Speed - USB Full-Speed - USB SuperSpeed • Knowledge Base Articles (KBA): - FX3 FAQs - KBA224051 - Trouble Shooting Guide for the FX3/FX3S/CX3 Enumeration - KBA222372 - EZ-USB™ FX3 Explorer kit as 16-channel 100 MHz logic analyzer with sigrok PulseView - KBA233652 - EZ-USB™ FX3-based HDMI-to-USB3 Vision solution demo kit - KBA235421 - EZ-USB™ FX3: Open source KiCad based schematic and BOM for FX3 camera kit - KBA236085 • Technical Reference Manual (TRM): - EZ-USB FX3 Technical Reference Manual • Development Kits: - CYUSB3KIT-003, EZ-USB FX3 SuperSpeed Explorer Kit • Models: IBIS Datasheet 4 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller More information 1.1 EZ-USB FX3 Software Development Kit Cypress delivers the complete software and firmware stack for FX3, in order to easily integrate SuperSpeed USB into any embedded application. The Software Development Kit (SDK) comes with tools, drivers and application examples, which help accelerate application development. 1.2 GPIF™ II Designer The GPIF II Designer is a graphical software that allows designers to configure the GPIF II interface of the EZ-USB FX3 USB 3.0 Device Controller. The tool allows users the ability to select from one of five Cypress supplied interfaces, or choose to create their own GPIF II interface from scratch. Cypress has supplied industry standard interfaces such as Asynchronous and Synchronous Slave FIFO, Asynchronous and Synchronous SRAM, and Asynchronous SRAM. Designers who already have one of these pre-defined interfaces in their system can simply select the interface of choice, choose from a set of standard parameters such as bus width (x8, 16, x32) endianess, clock settings, and compile the interface. The tool has a streamlined three step GPIF interface development process for users who need a customized interface. Users are able to first select their pin configuration and standard parameters. Secondly, they can design a virtual state machine using configurable actions. Finally, users can view output timing to verify that it matches the expected timing. Once the three step process is complete, the interface can be compiled and integrated with FX3. Datasheet 5 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Table of contents Table of contents Features ...........................................................................................................................................1 Applications......................................................................................................................................2 Functional description .......................................................................................................................2 Logic block diagram ..........................................................................................................................3 1 More information............................................................................................................................4 1.1 EZ-USB FX3 Software Development Kit .................................................................................................................5 1.2 GPIF™ II Designer.....................................................................................................................................................5 Table of contents ...............................................................................................................................6 2 Functional overview .......................................................................................................................8 2.1 Application examples .............................................................................................................................................8 3 USB interface ...............................................................................................................................10 3.1 OTG ........................................................................................................................................................................10 3.1.1 OTG connectivity................................................................................................................................................10 3.2 ReNumeration.......................................................................................................................................................11 3.3 VBUS overvoltage protection ...............................................................................................................................11 3.4 Carkit UART Mode .................................................................................................................................................11 4 GPIF II ..........................................................................................................................................12 4.0.1 Slave FIFO interface ...........................................................................................................................................12 5 CPU .............................................................................................................................................13 6 JTAG interface ..............................................................................................................................14 7 Other interfaces............................................................................................................................15 7.1 SPI interface ..........................................................................................................................................................15 7.2 UART interface ......................................................................................................................................................15 7.3 I2C interface ..........................................................................................................................................................15 7.4 I2S interface ..........................................................................................................................................................16 8 Boot options.................................................................................................................................17 9 Reset ...........................................................................................................................................18 9.1 Hard reset..............................................................................................................................................................18 9.2 Soft reset ...............................................................................................................................................................18 10 Clocking .....................................................................................................................................19 10.1 32-kHz watchdog timer clock input ...................................................................................................................20 11 Power ........................................................................................................................................21 11.1 Power Modes.......................................................................................................................................................21 12 Digital I/Os .................................................................................................................................24 13 GPIOs .........................................................................................................................................25 14 System-level ESD ........................................................................................................................26 15 Pin configurations.......................................................................................................................27 16 Pin description ...........................................................................................................................28 17 Electrical specifications...............................................................................................................32 17.1 Absolute maximum ratings ................................................................................................................................32 17.2 Operating conditions..........................................................................................................................................32 17.3 DC specifications.................................................................................................................................................33 18 Thermal characteristics ...............................................................................................................36 19 AC timing parameters..................................................................................................................37 19.1 GPIF II lines AC characteristics at 100 MHz ........................................................................................................37 19.2 GPIF II PCLK jitter characteristics.......................................................................................................................37 19.3 GPIF II timing .......................................................................................................................................................38 19.4 Slave FIFO interface ............................................................................................................................................41 19.4.1 Synchronous Slave FIFO Read sequence description....................................................................................41 19.4.2 Synchronous Slave FIFO Write sequence description ...................................................................................43 19.4.3 Asynchronous Slave FIFO Read sequence description ..................................................................................46 Datasheet 6 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Table of contents 19.4.4 Asynchronous Slave FIFO Write sequence description..................................................................................47 19.5 Host Processor Interface (P-Port) timing...........................................................................................................50 19.5.1 Asynchronous SRAM timing.............................................................................................................................50 19.5.2 ADMux timing for Asynchronous Access .........................................................................................................54 19.5.3 Synchronous ADMux timing ............................................................................................................................56 19.6 Serial Peripherals timing ....................................................................................................................................59 19.6.1 I2C timing .........................................................................................................................................................59 19.6.2 I2S timing diagram...........................................................................................................................................62 19.6.3 SPI timing specification ...................................................................................................................................63 19.7 Reset sequence ...................................................................................................................................................65 20 Package diagram ........................................................................................................................66 21 Ordering information ..................................................................................................................67 21.1 Ordering code definitions...................................................................................................................................67 22 Acronyms ...................................................................................................................................68 23 Document conventions................................................................................................................69 23.1 Units of measure .................................................................................................................................................69 24 Errata ........................................................................................................................................70 24.1 Qualification status.............................................................................................................................................70 24.2 Errata summary ..................................................................................................................................................70 Revision history ..............................................................................................................................75 Datasheet 7 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Functional overview 2 Functional overview Infineon’s EZ-USB FX3 is a SuperSpeed peripheral controller, providing integrated and flexible features. FX3 has a fully configurable, parallel, general programmable interface called GPIF II, which can connect to any processor, ASIC, or FPGA. GPIF II is an enhanced version of the GPIF in FX2LP, Infineon’s flagship USB 2.0 product. It provides easy and glueless connectivity to popular interfaces, such as asynchronous SRAM, asynchronous and synchronous address data multiplexed interfaces, and parallel ATA. FX3 has integrated the USB 3.2 Gen 1 and USB 2.0 physical layers (PHYs) along with a 32-bit ARM926EJ-S microprocessor for powerful data processing and for building custom applications. It implements an architecture that enables 375-MBps data transfer from GPIF II to the USB interface. An integrated USB 2.0 OTG controller enables applications in which FX3 may serve dual roles; for example, EZ-USB FX3 may function as an OTG Host to MSC as well as HID-class devices. FX3 contains 512 KB or 256 KB of on-chip SRAM (see “Ordering information” on page 67) for code and data. EZ-USB FX3 also provides interfaces to connect to serial peripherals such as UART, SPI, I2C, and I2S. FX3 comes with application development tools. The software development kit comes with firmware and host application examples for accelerating time to market. FX3 complies with the USB 3.2, Gen 1.0 specification and is also backward compatible with USB 2.0. It also complies with USB 2.0 OTG Specification v2.0. 2.1 Application examples In a typical application (see Figure 1), the FX3 functions as the main processor running the application software that connects external hardware to the SuperSpeed USB connection. Additionally, FX3 can function as a coprocessor connecting via the GPIF II interface to an application processor (see Figure 2) and operates as a subsystem providing SuperSpeed USB connectivity to the application processor. Crystal* Clock USB Host USB EZ-USB™ FX3 GPIF II External Slave Device (e.g. Image Sensor) I2 C *A clock input may be provided on the CLKIN pin instead of a crystal input EEPROM Figure 1 Datasheet EZ-USB FX3 as main processor 8 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Functional overview Crystal* Clock USB Host EZ-USB™ FX3 USB GPIF II External Master (e.g. MCU/CPU/ FPGA/ASIC) I2C * A clock input may be provided on the CLKIN pin instead of a crystal input EEPROM Figure 2 Datasheet EZ-USB FX3 as a coprocessor 9 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller USB interface 3 USB interface FX3 complies with the following specifications and supports the following features: • Supports USB peripheral functionality compliant with USB 3.2 Specification Revision 1.0 and is also backward compatible with the USB 2.0 Specification. • FX3 Hi-Speed parts (CYUSB201X) only support USB 2.0. • Complies with OTG Supplement Revision 2.0. It supports high-speed, full-speed, and low-speed OTG dual-role device capability. As a peripheral, FX3 is capable of SuperSpeed, high-speed, and full-speed. As a host, it is capable of high-speed, full-speed, and low-speed. • Supports Carkit Pass-Through UART functionality on USB D+/D– lines based on the CEA-936A specification. • Supports 16 IN and 16 OUT endpoints. • Supports USB Attached SCSI (UAS) device-class to optimize mass-storage access performance. • As a USB peripheral, application examples show that the FX3 supports UAS, USB Video Class (UVC), and Mass Storage Class (MSC) USB peripheral classes. All other device classes can be supported by customer firmware; a template example is provided as a starting point. • As an OTG host, application examples show that FX3 supports MSC and HID device classes. Note When the USB port is not in use, disable the PHY and transceiver to save power. 3.1 OTG FX3 is compliant with the OTG Specification Revision 2.0. In OTG mode, FX3 supports both A and B device modes and supports Control, Interrupt, Bulk, and Isochronous data transfers. FX3 requires an external charge pump (either standalone or integrated into a PMIC) to power VBUS in the OTG A-device mode. The Target Peripheral List for OTG host implementation consists of MSC- and HID-class devices. FX3 does not support Attach Detection Protocol (ADP). 3.1.1 OTG connectivity In OTG mode, FX3 can be configured to be an A, B, or dual-role device. It can connect to the following: • ACA device • Targeted USB peripheral • SRP-capable USB peripheral • HNP-capable USB peripheral • OTG host • HNP-capable host • OTG device Datasheet 10 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller USB interface 3.2 ReNumeration Because of FX3’s soft configuration, one chip can take on the identities of multiple distinct USB devices. When first plugged into USB, FX3 enumerates automatically with the Infineon Vendor ID (0x04B4) and downloads firmware and USB descriptors over the USB interface. The downloaded firmware executes an electrical disconnect and connect. FX3 enumerates again, this time as a device defined by the downloaded information. This patented two-step process, called ReNumeration, happens instantly when the device is plugged in. 3.3 VBUS overvoltage protection The maximum input voltage on FX3’s VBUS pin is 6 V. A charger can supply up to 9 V on VBUS. In this case, an external overvoltage protection (OVP) device is required to protect FX3 from damage on VBUS. Figure 3 shows the system application diagram with an OVP device connected on VBUS. Refer to Table 8 for the operating range of VBUS and VBATT. VIO5 AVDD VDD VIO4 CVDDQ VIO3 VIO2 VIO1 U3TXVDDQ U3RXVDDQ POWER SUBSYSTEM EZ-USB FX3 OVP device USB Connector 2 SSRXSSRX+ SSTXSSTX+ DD+ 3 4 5 6 7 8 9 VBUS OTG_ID USB-Port 1 GND Figure 3 System diagram with OVP device for VBUS 3.4 Carkit UART Mode The USB interface supports the Carkit UART mode (UART over D+/D–) for non-USB serial data transfer. This mode is based on the CEA-936A specification. In the Carkit UART mode, the output signaling voltage is 3.3 V. When configured for the Carkit UART mode, TXD of UART (output) is mapped to the D– line, and RXD of UART (input) is mapped to the D+ line. In the Carkit UART mode, FX3 disables the USB transceiver and D+ and D– pins serve as pass-through pins to connect to the UART of the host processor. The Carkit UART signals may be routed to the GPIF II interface or to GPIO[48] and GPIO[49], as shown in Figure 4. In this mode, FX3 supports a rate of up to 9600 bps. Ctrl Carkit UART Pass-through UART_ TXD TXD UART_ RXD RXD RXD(DP) Carkit UART Pass-through Interface on GPIOs Figure 4 Datasheet MUX DP USB PHY DM GPIO[48] (UART_TX) USB-Port ( ) Carkit UART Pass-through Interface on GPIF II TXD(DM) GPIO[49] ( UART_RX) Carkit UART Pass-through block diagram 11 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller GPIF II 4 GPIF II The high-performance GPIF II interface enables functionality similar to, but more advanced than, FX2LP’s GPIF and Slave FIFO interfaces. The GPIF II is a programmable state machine that enables a flexible interface that may function either as a master or slave in industry-standard or proprietary interfaces. Both parallel and serial interfaces may be implemented with GPIF II. Here is a list of GPIF II features: • Functions as master or slave • Provides 256 firmware programmable states • Supports 8-bit, 16-bit, 24-bit, and 32-bit parallel data bus • Enables interface frequencies up to 100 MHz • Supports 14 configurable control pins when a 32- bit data bus is used. All control pins can be either input/output or bidirectional. • Supports 16 configurable control pins when a 16/8 data bus is used. All control pins can be either input/output or bi-directional. GPIF II state transitions are based on control input signals. The control output signals are driven as a result of the GPIF II state transitions. The INT# output signal can be controlled by GPIF II. Refer to the GPIFII Designer tool. The GPIF II state machine’s behavior is defined by a GPIF II descriptor. The GPIF II descriptor is designed such that the required interface specifications are met. 8 KB of memory (separate from the 256/512 KB of embedded SRAM) is dedicated to the GPIF II waveform where the GPIF II descriptor is stored in a specific format. Infineon’s GPIFII Designer Tool enables fast development of GPIF II descriptors and includes examples for common interfaces. Example implementations of GPIF II are the asynchronous slave FIFO and synchronous slave FIFO interfaces. 4.0.1 Slave FIFO interface The Slave FIFO interface signals are shown in Figure 5. This interface allows an external processor to directly access up to four buffers internal to FX3. Further details of the Slave FIFO interface are described on page 41. Note Access to all 32 buffers is also supported over the slave FIFO interface. For details, contact Infineon applications support. SLCS# PKTEND FLAGB FLAGA External Master (For example, MCU/CPU/ FPGA/ASIC) A[1:0] D[31:0] EZ-USB FX3 SLWR# SLRD# SLOE# Note: Multiple Flags may be configured. Figure 5 Datasheet Slave FIFO interface 12 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller CPU 5 CPU FX3 has an on-chip 32-bit, 200-MHz ARM926EJ-S core CPU. The core has direct access to 16 KB of instruction tightly coupled memory (TCM) and 8 KB of Data TCM. The ARM926EJ-S core provides a JTAG interface for firmware debugging. FX3 offers the following advantages: • Integrates 256/512 KB of embedded SRAM for code and data and 8 KB of instruction cache and data cache. • Implements efficient and flexible DMA connectivity between the various peripherals (such as, USB, GPIF II, I2S, SPI, UART, I2C), requiring firmware only to configure data accesses between peripherals, which are then managed by the DMA fabric. • Allows easy application development using industry-standard development tools for ARM926EJ-S. Examples of the FX3 firmware are available with the Infineon EZ-USB FX3 Development Kit. Datasheet 13 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller JTAG interface 6 JTAG interface FX3’s JTAG interface has a standard five-pin interface to connect to a JTAG debugger in order to debug firmware through the CPU-core’s on-chip-debug circuitry. Industry-standard debugging tools for the ARM926EJ-S core can be used for the FX3 application development. For ARM JTAG access, TCK frequency should not be more than 1/6 of the CPU clock frequency. Datasheet 14 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Other interfaces 7 Other interfaces FX3 supports the following serial peripherals: • SPI • UART • I2C • I2S The SPI, UART, and I2S interfaces are multiplexed on the serial peripheral port. Table 7 shows details of how these interfaces are multiplexed. Note that when GPIF II is configured for a 32-bit data bus width (CYUSB3012 and CYUSB3014), then the SPI interface is not available. 7.1 SPI interface FX3 supports an SPI Master interface on the Serial Peripherals port. The maximum operation frequency is 33 MHz. The SPI controller supports four modes of SPI communication (see “SPI timing specification” on page 63 for details on the modes) with the Start-Stop clock. This controller is a single-master controller with a single automated SSN control. It supports transaction sizes ranging from four bits to 32 bits. 7.2 UART interface The UART interface of FX3 supports full-duplex communication. It includes the signals noted in Table 1. Table 1 UART interface signals Signal Description TX Output signal RX Input signal CTS Flow control RTS Flow control The UART is capable of generating a range of baud rates, from 300 bps to 4608 Kbps, selectable by the firmware. If flow control is enabled, then FX3’s UART only transmits data when the CTS input is asserted. In addition to this, FX3’s UART asserts the RTS output signal, when it is ready to receive data. 7.3 I2C interface FX3’s I2C interface is compatible with the I2C Bus Specification Revision 3. This I2C interface is capable of operating only as I2C master; therefore, it may be used to communicate with other I2C slave devices. For example, FX3 may boot from an EEPROM connected to the I2C interface, as a selectable boot option. FX3’s I2C Master Controller also supports multi-master mode functionality. The power supply for the I2C interface is VIO5, which is a separate power domain from the other serial peripherals. This gives the I2C interface the flexibility to operate at a different voltage than the other serial interfaces. The I2C controller supports bus frequencies of 100 kHz, 400 kHz, and 1 MHz. When VIO5 is 1.2 V, the maximum operating frequency supported is 100 kHz. When VIO5 is 1.8 V, 2.5 V, or 3.3 V, the operating frequencies supported are 400 kHz and 1 MHz. The I2C controller supports clock-stretching to enable slower devices to exercise flow control. The I2C interface’s SCL and SDA signals require external pull-up resistors. The pull-up resistors must be connected to VIO5. Datasheet 15 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Other interfaces 7.4 I2S interface FX3 has an I2S port to support external audio codec devices. FX3 functions as I2S Master as transmitter only. The I2S interface consists of four signals: clock line (I2S_CLK), serial data line (I2S_SD), word select line (I2S_WS), and master system clock (I2S_MCLK). FX3 can generate the system clock as an output on I2S_MCLK or accept an external system clock input on I2S_MCLK. The sampling frequencies supported by the I2S interface are 8 kHz, 16 kHz, 32 kHz, 44.1 kHz, 48 kHz, 96 kHz and 192 kHz. Datasheet 16 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Boot options 8 Boot options FX3 can load boot images from various sources, selected by the configuration of the PMODE pins. Following are the FX3 boot options: • Boot from USB • Boot from I2C • Boot from SPI - Infineon SPI Flash parts supported are S25FS064S (64-Mbit), S25FS128S (128-Mbit) and S25LFL064L (64-Mbit). - W25Q32FW (32-Mbit) is also supported. • Boot from GPIF II Sync ADMux mode Table 2 FX3 booting options PMODE[2:0][1] Datasheet Boot from F00 Sync ADMux (16-bit) F11 USB boot F1F I2C, On failure, USB boot is enabled 1FF I2C only 0F1 SPI, On failure, USB boot is enabled 17 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Reset 9 Reset 9.1 Hard reset A hard reset is initiated by asserting the Reset# pin on FX3. The specific reset sequence and timing requirements are detailed in Figure 29 and Table 23. All I/Os are tristated during a hard reset. Note however, that the on-chip bootloader has control after a hard reset and it will configure I/O signals depending on the selected boot mode; see AN76405 - EZ-USB® FX3™ Boot Options for more details. 9.2 Soft reset In a soft reset, the processor sets the appropriate bits in the PP_INIT control register. There are two types of soft reset: • CPU reset – The CPU program counter is reset. Firmware does not need to be reloaded following a CPU reset. • Whole device reset – This reset is identical to hard reset. • The firmware must be reloaded following a whole device reset. Note 1. F indicates floating. Datasheet 18 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Clocking 10 Clocking FX3 allows either a crystal to be connected between the XTALIN and XTALOUT pins or an external clock to be connected at the CLKIN pin. The XTALIN, XTALOUT, CLKIN, and CLKIN_32 pins can be left unconnected if they are not used. Crystal frequency supported is 19.2 MHz, while the external clock frequencies supported are 19.2, 26, 38.4, and 52 MHz. FX3 has an on-chip oscillator circuit that uses an external 19.2-MHz (±100 ppm) crystal (when the crystal option is used). An appropriate load capacitance is required with a crystal. Refer to the specification of the crystal used to determine the appropriate load capacitance. The FSLC[2:0] pins must be configured appropriately to select the crystal- or clock-frequency option. The configuration options are shown in Table 3. Clock inputs to FX3 must meet the phase noise and jitter requirements specified in Table 4. The input clock frequency is independent of the clock and data rate of the FX3 core or any of the device interfaces. The internal PLL applies the appropriate clock multiply option depending on the input frequency. Table 3 Crystal/clock frequency selection FSLC[2] FSLC[1] FSLC[0] Crystal/clock frequency 0 0 0 19.2-MHz crystal 1 0 0 19.2-MHz input CLK 1 0 1 26-MHz input CLK 1 1 0 38.4-MHz input CLK 1 1 1 52-MHz input CLK Table 4 FX3 input clock specifications Parameter Specification Description Min Max 100-Hz offset – –75 1-kHz offset – –104 10-kHz offset – –120 100-kHz offset – –128 1-MHz offset – –130 Maximum frequency deviation – – 150 Duty cycle – 30 70 Overshoot – – 3 Undershoot – – –3 Rise time/fall time – – 3 Phase noise Datasheet 19 Units dB ppm % ns 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Clocking 10.1 32-kHz watchdog timer clock input FX3 includes a watchdog timer. The watchdog timer can be used to interrupt the ARM926EJ-S core, automatically wake up the FX3 in Standby mode, and reset the ARM926EJ-S core. The watchdog timer runs a 32-kHz clock, which may be optionally supplied from an external source on a dedicated FX3 pin. The firmware can disable the watchdog timer. Requirements for the optional 32-kHz clock input are listed in Table 5. Table 5 32-kHz clock input requirements Parameter Min Max Units Duty cycle 40 60 % Frequency deviation – ±200 ppm Rise time/fall time – 200 ns Datasheet 20 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Power 11 Power FX3 has the following power supply domains: • IO_VDDQ: This is a group of independent supply domains for digital I/Os. The voltage level on these supplies is 1.8 V to 3.3 V. FX3 provides six independent supply domains for digital I/Os listed as follows (see Table 7 for details on each of the power domain signals): - VIO1: GPIF II I/O - VIO2: IO2 - VIO3: IO3 - VIO4: UART-/SPI/I2S - VIO5: I2C and JTAG (supports 1.2 V to 3.3 V) - CVDDQ: This is the supply voltage for clock and reset I/O. It should be either 1.8 V or 3.3 V based on the voltage level of the CLKIN signal. - VDD: This is the supply voltage for the logic core. The nominal supply-voltage level is 1.2 V. This supplies the core logic circuits. The same supply must also be used for the following: • AVDD: This is the 1.2-V supply for the PLL, crystal oscillator, and other core analog circuits. • U3TXVDDQ/U3RXVDDQ: These are the 1.2-V supply voltages for the USB 3.0 interface. • VBATT/VBUS: This is the 3.2-V to 6-V battery power supply for the USB I/O and analog circuits. This supply powers the USB transceiver through FX3’s internal voltage regulator. VBATT is internally regulated to 3.3 V. Note: No specific power-up sequence for FX3 power domains. Minimum power on reset time of 1 ms should be met and the power domains must be stable for FX3 operation. 11.1 Power Modes FX3 supports the following power modes: • Normal mode: This is the full-functional operating mode. The internal CPU clock and the internal PLLs are enabled in this mode. - Normal operating power consumption does not exceed the sum of ICC Core max and ICC USB max (see Table 8 for current consumption specifications). - The I/O power supplies VIO2, VIO3, VIO4, and VIO5 can be turned off when the corresponding interface is not in use. VIO1 cannot be turned off at any time if the GPIF II interface is used in the application. • Low-power modes (see Table 6): - Suspend mode with USB 3.0 PHY enabled (L1) - Suspend mode with USB 3.0 PHY disabled (L2) - Standby mode (L3) - Core power-down mode (L4) Datasheet 21 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Power Table 6 Entry and Exit methods for Low-Power Modes Low-Power Mode Characteristics • The power consumption in this mode does not exceed ISB1 • USB 3.0 PHY is enabled and is in U3 mode (one of the suspend modes defined by the USB 3.0 specification). This one block alone is operational with its internal clock while all other clocks are shut down • All I/Os maintain their previous state • Power supply for the wakeup source and Suspend Mode with USB 3.0 PHY Enabled (L1) Methods of Entry Methods of Exit • Firmware executing on ARM926EJ-S core • D+ transitioning to low or can put FX3 into suspend mode. For example, on USB suspend condition, firmware may decide to put FX3 into suspend mode • External Processor, through the use of mailbox registers, can put FX3 into suspend mode high • D– transitioning to low or high • Impedance change on OTG_ID pin • Resume condition on SSRX± • Detection of VBUS • Level detect on core power must be retained. All other power domains can be turned on/off individually UART_CTS (programmable polarity) • The states of the configuration registers, • GPIF II interface assertion buffer memory, and all internal RAM are maintained of CTL[0] • All transactions must be completed • Assertion of RESET# before FX3 enters Suspend mode (state of outstanding transactions are not preserved) • The firmware resumes operation from where it was suspended (except when woken up by RESET# assertion) because the program counter does not reset • The power consumption in this mode does not exceed ISB2 • USB 3.0 PHY is disabled and the USB interface is in suspend mode • The clocks are shut off. The PLLs are disabled • All I/Os maintain their previous state • USB interface maintains the previous • Firmware executing on ARM926EJ-S core • D+ transitioning to low or can put FX3 into suspend mode. For example, on USB suspend condition, firmware may decide to put FX3 into suspend mode • External Processor, through the use of mailbox registers can put FX3 into suspend mode state Suspend Mode with USB 3.0 PHY Disabled (L2) high • D– transitioning to low or high • Impedance change on OTG_ID pin • Detection of VBUS • Level detect on UART_CTS (programmable polarity) • Power supply for the wakeup source and • GPIF II interface assertion core power must be retained. All other power domains can be turned on/off individually of CTL[0] • Assertion of RESET# • The states of the configuration registers, buffer memory and all internal RAM are maintained • All transactions must be completed before FX3 enters Suspend mode (state of outstanding transactions are not preserved) • The firmware resumes operation from where it was suspended (except when woken up by RESET# assertion) because the program counter does not reset Datasheet 22 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Power Table 6 Entry and Exit methods for Low-Power Modes (continued) Low-Power Mode Characteristics • The power consumption in this mode does not exceed ISB3 • All configuration register settings and Methods of Entry Methods of Exit • Firmware executing on ARM926EJ-S core • Detection of VBUS or external processor configures the • Level detect on appropriate register UART_CTS (Programmable Polarity) program/data RAM contents are preserved. However, data in the buffers or other parts of the data path, if any, is not guaranteed. Therefore, the external processor should take care that the data needed is read before putting FX3 into this Standby Mode • GPIF II interface assertion of CTL[0] • Assertion of RESET# • The program counter is reset after Standby Mode (L3) waking up from Standby • • • • • GPIO pins maintain their configuration Crystal oscillator is turned off Internal PLL is turned off USB transceiver is turned off ARM926EJ-S core is powered down. Upon wakeup, the core re-starts and runs the program stored in the program/data RAM • Power supply for the wakeup source and core power must be retained. All other power domains can be turned on/off individually • The power consumption in this mode does not exceed ISB4 Core Power Down Mode (L4) • Turn off VDD • Core power is turned off • All buffer memory, configuration • Reapply VDD • Assertion of RESET# registers, and the program RAM do not maintain state. After exiting this mode, reload the firmware • In this mode, all other power domains can be turned on/off individually Note: The power consumption depends on how the FX3 IOs are utilized in the application. Refer to KBA85505 to estimate the current consumption by different power domains (VIO1–VIO5). Datasheet 23 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Digital I/Os 12 Digital I/Os FX3 has internal firmware-controlled pull-up or pull-down resistors on all digital I/O pins. An internal 50-k resistor pulls the pins high, while an internal 10-k resistor pulls the pins low to prevent them from floating. The I/O pins may have the following states: • Tristated (High-Z) • • • • Weak pull-up (via internal 50 k) Pull-down (via internal 10 k) Hold (I/O hold its value) when in low-power modes The JTAG TDI, TMS, and TRST# signals have fixed 50-kinternal pull-ups, and the TCK signal has a fixed 10-k pull-down resistor. All unused I/Os should be pulled high by using the internal pull-up resistors. All unused outputs should be left floating. All I/Os can be driven at full-strength, three-quarter strength, half-strength, or quarter-strength. These drive strengths are configured separately for each interface. Datasheet 24 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller GPIOs 13 GPIOs EZ-USB enables a flexible pin configuration both on the GPIF II and the serial peripheral interfaces. Any unused control pins (except CTL[15]) on the GPIF II interface can be used as GPIOs. Similarly, any unused pins on the serial peripheral interfaces may be configured as GPIOs. See “Pin configurations” on page 27 for pin configuration options. All GPIF II and GPIO pins support an external load of up to 16 pF for every pin. EMI FX3 meets EMI requirements outlined by FCC 15B (USA) and EN55022 (Europe) for consumer electronics. FX3 can tolerate EMI, conducted by the aggressor, outlined by these specifications and continue to function as expected. Datasheet 25 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller System-level ESD 14 System-level ESD FX3 has built-in ESD protection on the D+, D–, and GND pins on the USB interface. The ESD protection levels provided on these ports are: • ±2.2-kV human body model (HBM) based on JESD22-A114 Specification • ±6-kV contact discharge and ±8-kV air gap discharge based on IEC61000-4-2 level 3A • ± 8-kV Contact Discharge and ±15-kV Air Gap Discharge based on IEC61000-4-2 level 4C. This protection ensures the device continues to function after ESD events up to the levels stated in this section. The SSRX+, SSRX–, SSTX+, and SSTX– pins only have up to ±2.2-kV HBM internal ESD protection. Datasheet 26 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Pin configurations 15 A Pin configurations 1 2 3 4 5 6 7 8 9 10 11 U3VSSQ U3RXVDDQ SSRXM SSRXP SSTXP SSTXM AVDD VSS DP DM NC B VIO4 FSLC[0] R_USB3 FSLC[1] U3TXVDDQ CVDDQ AVSS VSS VSS VDD TRST# C GPIO[54] GPIO[55] VDD GPIO[57] RESET# XTALIN XTALOUT R_USB2 OTG_ID TDO VIO5 D GPIO[50] GPIO[51] GPIO[52] GPIO[53] GPIO[56] CLKIN_32 CLKIN VSS I2C_GPIO[58] I2C_GPIO[59] NC E GPIO[47] VSS VIO3 GPIO[49] GPIO[48] FSLC[2] TDI TMS VDD VBATT VBUS F VIO2 GPIO[45] GPIO[44] GPIO[41] GPIO[46] TCK GPIO[2] GPIO[5] GPIO[1] GPIO[0] VDD G VSS GPIO[42] GPIO[43] GPIO[30] GPIO[25] GPIO[22] GPIO[21] GPIO[15] GPIO[4] GPIO[3] VSS H VDD GPIO[39] GPIO[40] GPIO[31] GPIO[29] GPIO[26] GPIO[20] GPIO[24] GPIO[7] GPIO[6] VIO1 J GPIO[38] GPIO[36] GPIO[37] GPIO[34] GPIO[28] GPIO[16] GPIO[19] GPIO[14] GPIO[9] GPIO[8] VDD K GPIO[35] GPIO[33] VSS VSS GPIO[27] GPIO[23] GPIO[18] GPIO[17] GPIO[13] GPIO[12] GPIO[10] L VSS VSS VSS GPIO[32] VDD VSS VDD INT# VIO1 GPIO[11] VSS Figure 6 A FX3 121-ball BGA ball map (Top view) 1 2 3 4 5 6 7 8 9 10 11 VSS VDD NC NC NC NC AVDD VSS DP DM NC B VIO4 FSLC[0] NC FSLC[1] VDD CVDDQ AVSS VSS VSS VDD TRST# C GPIO[54] GPIO[55] VDD GPIO[57] RESET# XTALIN XTALOUT R_USB2 OTG_ID TDO VIO5 D GPIO[50] GPIO[51] GPIO[52] GPIO[53] GPIO[56] CLKIN_32 CLKIN VSS I2C_GPIO[58] I2C_GPIO[59] NC E GPIO[47] VSS VIO3 GPIO[49] GPIO[48] FSLC[2] TDI TMS VDD VBATT VBUS F VIO2 GPIO[45] GPIO[44] GPIO[41] GPIO[46] TCK GPIO[2] GPIO[5] GPIO[1] GPIO[0] VDD G VSS GPIO[42] GPIO[43] GPIO[30] GPIO[25] GPIO[22] GPIO[21] GPIO[15] GPIO[4] GPIO[3] VSS H VDD GPIO[39] GPIO[40] GPIO[31] GPIO[29] GPIO[26] GPIO[20] GPIO[24] GPIO[7] GPIO[6] VIO1 J GPIO[38] GPIO[36] GPIO[37] GPIO[34] GPIO[28] GPIO[16] GPIO[19] GPIO[14] GPIO[9] GPIO[8] VDD K GPIO[35] GPIO[33] VSS VSS GPIO[27] GPIO[23] GPIO[18] GPIO[17] GPIO[13] GPIO[12] GPIO[10] L VSS VSS VSS GPIO[32] VDD VSS VDD INT# VIO1 GPIO[11] VSS Figure 7 FX3 Hi-Speed 121-ball BGA ball map (Top view) Note: A2 and C3 need not be connected for FX3 Hi-Speed part. Datasheet 27 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Pin description 16 Pin description Table 7 CYUSB3011, CYUSB3012, CYUSB3013, CYUSB3014 and CYUSB2014 pin list BGA Power domain I/O Name Description GPIF II interface Slave FIFO interface [2] F10 VIO1 I/O GPIO[0] DQ[0] DQ[0] F9 VIO1 I/O GPIO[1] DQ[1] DQ[1] F7 VIO1 I/O GPIO[2] DQ[2] DQ[2] G10 VIO1 I/O GPIO[3] DQ[3] DQ[3] G9 VIO1 I/O GPIO[4] DQ[4] DQ[4] F8 VIO1 I/O GPIO[5] DQ[5] DQ[5] H10 VIO1 I/O GPIO[6] DQ[6] DQ[6] H9 VIO1 I/O GPIO[7] DQ[7] DQ[7] GPIO[8] DQ[8]/A0 [3] DQ[8]/A0 [3] GPIO[9] DQ[9]/A1 [3] DQ[9]/A1 [3] J10 J9 VIO1 VIO1 I/O I/O K11 VIO1 I/O GPIO[10] DQ[10] DQ[10] L10 VIO1 I/O GPIO[11] DQ[11] DQ[11] K10 VIO1 I/O GPIO[12] DQ[12] DQ[12] K9 VIO1 I/O GPIO[13] DQ[13] DQ[13] J8 VIO1 I/O GPIO[14] DQ[14] [4] DQ[14] [4] G8 VIO1 I/O GPIO[15] DQ[15] [4] DQ[15] [4] J6 VIO1 I/O GPIO[16] PCLK CLK K8 VIO1 I/O GPIO[17] CTL[0] SLCS# K7 VIO1 I/O GPIO[18] CTL[1] SLWR# J7 VIO1 I/O GPIO[19] CTL[2] SLOE# H7 VIO1 I/O GPIO[20] CTL[3] SLRD# G7 VIO1 I/O GPIO[21] CTL[4] FLAGA G6 VIO1 I/O GPIO[22] CTL[5] FLAGB K6 VIO1 I/O GPIO[23] CTL[6] GPIO H8 VIO1 I/O GPIO[24] CTL[7] PKTEND# G5 VIO1 I/O GPIO[25] CTL[8] GPIO H6 VIO1 I/O GPIO[26] CTL[9] GPIO K5 VIO1 I/O GPIO[27] CTL[10] GPIO J5 VIO1 I/O GPIO[28] CTL[11] A1 H5 VIO1 I/O GPIO[29] CTL[12] A0 G4 VIO1 I/O GPIO[30] PMODE[0] PMODE[0] H4 VIO1 I/O GPIO[31] PMODE[1] PMODE[1] L4 VIO1 I/O GPIO[32] PMODE[2] PMODE[2] L8 VIO1 I/O INT# INT#/CTL[15] CTL[15] Notes 2. Slave FIFO is an example configuration of GPIF II Interface. The Slave FIFO control signal assignments can be modified using GPIF-II designer tool. 3. For 8-bit data bus configuration, GPIO[8] and GPIO[9] act as address lines. 4. GPIF II can also be configured as a serial interface. The DQ[15] pin becomes a serial output and DQ[14] becomes a serial input in this mode. Datasheet 28 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Pin description Table 7 BGA CYUSB3011, CYUSB3012, CYUSB3013, CYUSB3014 and CYUSB2014 pin list (continued) Power domain I/O Name Description CYUSB3014 and CYUSB2014 32-bit Data Bus CYUSB3011, CYUSB3012, CYUSB3013, CYUSB3014 and CYUSB2014 16-bit 16-bit Data Bus Data 16-bit 16-bit Bus + Data + UART + SPI + Bus + Data Bus + UART + I2S SPI + GPIO I2S + GPIO GPIO GPIO only K2 VIO2 I/O GPIO[33] DQ[16] GPIO GPIO GPIO GPIO GPIO J4 VIO2 I/O GPIO[34] DQ[17] GPIO GPIO GPIO GPIO GPIO K1 VIO2 I/O GPIO[35] DQ[18] GPIO GPIO GPIO GPIO GPIO J2 VIO2 I/O GPIO[36] DQ[19] GPIO GPIO GPIO GPIO GPIO J3 VIO2 I/O GPIO[37] DQ[20] GPIO GPIO GPIO GPIO GPIO J1 VIO2 I/O GPIO[38] DQ[21] GPIO GPIO GPIO GPIO GPIO H2 VIO2 I/O GPIO[39] DQ[22] GPIO GPIO GPIO GPIO GPIO H3 VIO2 I/O GPIO[40] DQ[23] GPIO GPIO GPIO GPIO GPIO F4 VIO2 I/O GPIO[41]/A0 [5] DQ[24] GPIO GPIO GPIO GPIO GPIO G2 VIO2 I/O GPIO[42]/A1 [5] DQ[25] GPIO GPIO GPIO GPIO GPIO G3 VIO2 I/O GPIO[43] DQ[26] GPIO GPIO GPIO GPIO GPIO F3 VIO2 I/O GPIO[44] DQ[27] GPIO GPIO GPIO GPIO GPIO F2 VIO2 I/O GPIO[45] GPIO GPIO GPIO GPIO GPIO GPIO F5 VIO3 I/O GPIO[46] DQ[28] UART_RT S GPIO GPIO GPIO GPIO E1 VIO3 I/O GPIO[47] DQ[29] UART_CT S GPIO GPIO GPIO GPIO E5 VIO3 I/O GPIO[48] DQ[30] UART_TX GPIO GPIO GPIO GPIO E4 VIO3 I/O GPIO[49] DQ[31] UART_R X GPIO GPIO GPIO GPIO D1 VIO3 I/O GPIO[50] I2S_CLK I2S_CLK GPIO GPIO GPIO GPIO D2 VIO3 I/O GPIO[51] I2S_SD I2S_SD GPIO GPIO GPIO GPIO D3 VIO3 I/O GPIO[52] I2S_WS I2S_WS GPIO GPIO GPIO GPIO D4 VIO4 I/O GPIO[53] UART_RTS SPI_SCK UART_RTS SPI_SCK GPIO GPIO C1 VIO4 I/O GPIO[54] UART_CTS SPI_SSN UART_CTS SPI_SSN I2S_CLK GPIO C2 VIO4 I/O GPIO[55] UART_TX SPI_MIS O UART_TX SPI_MISO I2S_SD GPIO D5 VIO4 I/O GPIO[56] UART_RX SPI_MOS I UART_RX SPI_MOSI I2S_WS GPIO C4 VIO4 I/O GPIO[57] I2S_MCLK I2S_MCL K GPIO GPIO I2S_MCLK GPIO USB Port CYUSB301X CYUSB201X A3 U3RXVDDQ I SSRXM SSRX- NC A4 U3RXVDDQ I SSRXP SSRX+ NC A6 U3TXVDDQ O SSTXM SSTX- NC A5 U3TXVDDQ O SSTXP SSTX+ NC B3 U3TXVDDQ I/O R_usb3 Precision resistor for USB 3.0 (Connect a 200 ±1% resistor between this pin and GND) NC C9 VBUS/VBATT I OTG_ID OTG_ID A9 VBUS/VBATT I/O DP D+ A10 VBUS/VBATT I/O DM D– C8 VBUS/VBATT I/O R_usb2 Precision resistor for USB 2.0 (Connect a 6.04 k ±1% resistor between this pin and GND) Note 5. For 24-bit data bus configuration, GPIO[41] and GPIO[42] act as address lines. Datasheet 29 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Pin description Table 7 BGA CYUSB3011, CYUSB3012, CYUSB3013, CYUSB3014 and CYUSB2014 pin list (continued) Power domain I/O Name Description Clock and Reset B2 CVDDQ I FSLC[0] FSLC[0] C6 AVDD I/O XTALIN XTALIN C7 AVDD I/O XTALOUT XTALOUT B4 CVDDQ I FSLC[1] FSLC[1] E6 CVDDQ I FSLC[2] FSLC[2] D7 CVDDQ I CLKIN CLKIN D6 CVDDQ I CLKIN_32 CLKIN_32 C5 CVDDQ I RESET# RESET# D9 VIO5 I/O I2C_GPIO[58] I2C_SCL D10 VIO5 I/O I2C_GPIO[59] I2C_SDA I2C and JTAG E7 VIO5 I TDI TDI C10 VIO5 O TDO TDO B11 VIO5 I TRST# TRST# E8 VIO5 I TMS TMS F6 VIO5 I TCK TCK D11 VIO5 O O[60] GPIO Power E10 B10 PWR VBATT PWR VDD PWR VDD A1 PWR U3VSSQ E11 PWR VBUS D8 PWR VSS H11 PWR VIO1 E2 PWR VSS L9 PWR VIO1 G1 PWR VSS PWR VIO1 PWR VSS F1 PWR VIO2 G11 PWR VSS PWR VIO2 E3 PWR VIO3 L1 PWR VSS B1 PWR VIO4 L6 PWR VSS PWR VSS B6 PWR CVDDQ B5 PWR U3TXVDDQ A2 PWR U3RXVDDQ C11 PWR VIO5 L11 PWR VSS A7 PWR AVDD Datasheet 30 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Pin description Table 7 BGA CYUSB3011, CYUSB3012, CYUSB3013, CYUSB3014 and CYUSB2014 pin list (continued) I/O Name B7 Power domain PWR AVSS Description C3 PWR VDD B8 PWR VSS E9 PWR VDD B9 PWR VSS F11 PWR VDD PWR VSS PWR VDD PWR VSS GND GND PWR VSS H1 PWR VDD L7 PWR VDD J11 PWR VDD L5 PWR VDD K4 PWR VSS L3 PWR VSS K3 PWR VSS L2 PWR VSS A8 PWR VSS A11 Datasheet GND NC No Connect NC No Connect 31 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Electrical specifications 17 Electrical specifications 17.1 Absolute maximum ratings Exceeding maximum ratings may shorten the useful life of the device. Storage temperature ......................... –65°C to +150°C Ambient temperature with power supplied (Industrial) ................ –40°C to +85°C Ambient temperature with power supplied (Commercial) ................ 0°C to +70°C Supply voltage to ground potential VDD, AVDDQ ...........................................................1.25 V VIO1,VIO2, VIO3, VIO4, VIO5 .......................................3.6 V U3TXVDDQ, U3RXVDDQ .........................................1.25 V DC input voltage to any input pin ...............VCC + 0.3 V DC voltage applied to outputs in high Z state ............................... VCC + 0.3 V (VCC is the corresponding I/O voltage) Static discharge voltage ESD protection levels: • ± 2.2-kV HBM based on JESD22-A114 • Additional ESD protection levels on D+, D–, and GND pins, and serial peripheral pins • ± 6-kV contact discharge, ± 8-kV air gap discharge based on IEC61000-4-2 level 3A, ± 8-kV contact discharge, and ± 15-kV air gap discharge based on IEC61000-4-2 level 4C Latch-up current ............................................ 180 mA Maximum output short-circuit current for all I/Os (cumulative) ................................ –100 mA Maximum output current per I/O (source or sink) .................................................. 20 mA 17.2 Operating conditions TA (ambient temperature under bias) Industrial ............................................. –40°C to +85°C Commercial ............................................ 0°C to +70°C VDD, AVDDQ, U3TXVDDQ, U3RXVDDQ Supply voltage .....................................1.15 V to 1.25 V VBATT supply voltage ..................................3.2 V to 6 V VIO1, VIO2, VIO3, VIO4, CVDDQ Supply voltage .........................................1.7 V to 3.6 V VIO5 supply voltage ................... ............ 1.15 V to 3.6 V Datasheet 32 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Electrical specifications 17.3 DC specifications Table 8 DC specifications Parameter Description Min Max Units VDD Core voltage supply 1.15 1.25 V 1.2-V typical AVDD Analog voltage supply 1.15 1.25 V 1.2-V typical VIO1 GPIF II I/O power supply domain 1.7 3.6 V 1.8-, 2.5-, and 3.3-V typical VIO2 IO2 power supply domain 1.7 3.6 V 1.8-, 2.5-, and 3.3-V typical VIO3 IO3 power supply domain 1.7 3.6 V 1.8-, 2.5-, and 3.3-V typical VIO4 UART/SPI/I2S power supply domain 1.7 3.6 V 1.8-, 2.5-, and 3.3-V typical VBATT USB voltage supply 3.2 6 V 3.7-V typical VBUS USB voltage supply 4.0 6 V 5-V typical V 1.2-V typical. A 22-µF bypass capacitor is required on this power supply. N/A for CYUSB201X U3TXVDDQ USB 3.0 1.2-V supply 1.15 1.25 Notes U3RXVDDQ USB 3.0 1.2-V supply 1.15 1.25 V 1.2-V typical. A 22-µF bypass capacitor is required on this power supply. N/A for CYUSB201X CVDDQ Clock voltage supply 1.7 3.6 V 1.8-, 3.3-V typical VIO5 I2C and JTAG voltage supply 1.15 3.6 V 1.2-, 1.8-, 2.5-, and 3.3-V typical VIH1 Input HIGH voltage 1 0.625 × VCC VCC + 0.3 V For 2.0 V  VCC  3.6 V (except USB port). VCC is the corresponding I/O voltage supply. VIH2 Input HIGH voltage 2 VCC – 0.4 VCC + 0.3 V For 1.7 V  VCC 2.0 V (except USB port). VCC is the corresponding I/O voltage supply. VIL Input LOW voltage –0.3 0.25 × VCC V VCC is the corresponding I/O voltage supply. V IOH (max) = –100 µA tested at quarter drive strength. VCC is the corresponding I/O voltage supply. Refer toTable 9 for values of IOH at various drive strength and VCC. V IOL (min) = +100 µA tested at quarter drive strength. VCC is the corresponding I/O voltage supply. Refer to Table 9 for values of IOL measured at various drive strength and VCC. µA All I/O signals held at VDDQ (For I/Os with a pull-up or pull-down resistor connected, the leakage current increases by VDDQ/Rpu or VDDQ/RPD) VOH Output HIGH voltage VOL Output LOW voltage IIX Input leakage current for all pins except SSTXP/SSXM/SSRXP/SSRXM Datasheet 0.9 × VCC – – 0.1 × VCC –1 1 33 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Electrical specifications Table 8 Parameter DC specifications (continued) Min Max Units IOZ Output High-Z leakage current for all pins except SSTXP/ SSXM/ SSRXP/SSRXM –1 1 µA All I/O signals held at VDDQ ICC Core Core and analog voltage operating current – 200 mA Total current through AVDD, VDD ICC USB [6] USB voltage supply operating current – 60 [6] mA – mA Core current: 1.5 mA I/O current: 20 µA USB current: 2 mA For typical PVT (typical silicon, all power supplies at their respective nominal levels at 25°C) mA Core current: 250 µA I/O current: 20 µA USB current: 1.2 mA For typical PVT (Typical silicon, all power supplies at their respective nominal levels at 25°C) µA Core current: 60 µA I/O current: 20 µA USB current: 40 µA For typical PVT (typical silicon, all power supplies at their respective nominal levels at 25°C) µA Core current: 0 µA I/O current: 20 µA USB current: 40 µA For typical PVT (typical silicon, all power supplies at their respective nominal levels at 25°C) ISB1 ISB2 ISB3 Description Total suspend current during suspend mode with USB 3.0 PHY enabled (L1) Total suspend current during suspend mode with USB 3.0 PHY disabled (L2) Total standby current during standby mode (L3) – – – – – – Notes ISB4 Total standby current during core power-down mode (L4) – – VRAMP Voltage ramp rate on core and I/O supplies 0.2 50 VN Noise level permitted on VDD and I/O supplies – 100 mV Max p-p noise level permitted on all supplies except AVDD VN_AVDD Noise level permitted on AVDD supply – 20 mV Max p-p noise level permitted on AVDD V/ms Voltage ramp must be monotonic Note 6. For CYUSB2014 ICC USB is typically 22 mA–23 mA. Datasheet 34 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Electrical specifications Table 9 VDDIO (V) 1.7 2.5 3.6 Datasheet IOH/IOL values for different drive strength and VDDIO values VOH (V) 1.53 2.25 3.24 VOL (V) 0.17 0.25 0.36 Drive strength IOH max (mA) IOL min (mA) Quarter 1.02 2.21 Half 1.51 3.28 Three-quarters 1.83 3.85 Full 2.28 4.73 Quarter 5.03 3.96 Half 7.38 5.84 Three-quarters 8.89 6.89 Full 11.07 8.61 Quarter 7.80 5.74 Half 11.36 8.64 Three-quarters 13.64 10.15 Full 16.92 12.67 35 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Thermal characteristics 18 Thermal characteristics Table 10 Thermal characteristics Parameter TJ MAX JA JB JC Datasheet Description Value Unit 125 °C Thermal resistance (Junction to ambient) 34.66 °C/W Thermal resistance (Junction to board) 27.03 °C/W Thermal resistance (Junction to case) 13.57 °C/W Maximum junction temperature 36 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters 19 AC timing parameters 19.1 GPIF II lines AC characteristics at 100 MHz Table 11 GPIF II lines AC characteristics at 100 MHz Symbol Parameter Min Typ Max Unit Tr Rise time – – 2.5 ns Tf Fall time – – 2.5 ns Tov Overshoot – – 3 % Tun Undershoot – – 3 % 19.2 GPIF II PCLK jitter characteristics Table 12 GPIF II PCLK jitter characteristics Clk Freq (MHz) Period jitter (ps) C-C min (ps) C-C max (ps) 10.08 354.44 –187.92 204.55 25.2 205.97 –153.54 126.53 50.4 144.62 –100.16 85.769 100.8 171.43 –155.13 157.14 Note 7. The clock jitter is measured using internally generated PCLK. ie. PCLK is configured as an output from GPIF. The data is measured over 10,000 clock cycles. Datasheet 37 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters 19.3 GPIF II timing tC LK H tC LKL C LK tC LK tLZ - [31:0] DQ tD S tC O E tD H tLZ tH Z tD O H tD O H D ata 2 ( O U T) D ata 1 ( O U T) D ata ( IN) tS tC O tH C TL(IN) tC TLO tC O H C TL ( O U T) Figure 8 GPIF II timing in Synchronous Mode Table 13 GPIF II timing parameters in Synchronous Mode [8] Parameter Description Min Max Units Frequency Interface clock frequency – 100 MHz tCLK Interface clock period 10 – ns tCLKH Clock high time 4 – ns tCLKL Clock low time 4 – ns tS CTL input to clock setup time 2 – ns tH CTL input to clock hold time 0.5 – ns tDS Data in to clock setup time 2 – ns tDH Data in to clock hold time 0.5 – ns tCO Clock to data out propagation delay when DQ bus is already in output direction – 7 ns tCOE Clock to data out propagation delay when DQ lines change to output from tristate and valid data is available on the DQ bus – 9 ns tCTLO Clock to CTL out propagation delay – 8 ns tDOH Clock to data out hold 2 – ns tCOH Clock to CTL out hold 0 – ns tHZ Clock to high-Z – 8 ns tLZ Clock to low-Z 0 – ns Note 8. All parameters guaranteed by design and validated through characterization. Datasheet 38 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters tDS/ tAS tDH/tAH DATA IN DATA/ ADDR tCHZ CTL# (I/P , ALE/ DLE) tCTLassert_DQlatch tCTLdeassert_DQlatch tAA/tDO tCHZ/tOEHZ tCLZ/ tOELZ DATA OUT DATA OUT CTL# (I/P, non ALE/ DLE tCTLdeassert tCTLassert tCTLalpha ALPHA O/P tCTLbeta BETA O/P 1 tCTLassert tCTLdeassert 1 tCTL# (O/P) 1. n is an integer >= 0 tDST tDHT DATA/ ADDR tCTLdeassert_DQassert tCTLassert_DQassert CTL# I/P (non DLE/ALE) Figure 9 GPIF II timing in Asynchronous Mode tDS CTL# (I/P) tCTLdeassert_DqlatchDDR tCTLassert_DQlatchDDR tDS tDH tDH DATA IN Figure 10 Datasheet GPIF II timing in Asynchronous DDR Mode 39 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters Table 14 GPIF II timing in Asynchronous Mode[9, 10] Note The following parameters assume one state transition Parameter Description Min Max Units tDS Data In to DLE setup time. Valid in DDR async mode. 2.3 – ns tDH Data In to DLE hold time. Valid in DDR async mode. 2 – ns tAS Address In to ALE setup time 2.3 – ns tAH Address In to ALE hold time 2 – ns tCTLassert CTL I/O asserted width for CTRL inputs without DQ input association and for outputs. 7 – ns tCTLdeassert CTL I/O deasserted width for CTRL inputs without DQ input association and for outputs. 7 – ns tCTLassert_DQassert CTL asserted pulse width for CTL inputs that signify DQ inputs valid at the asserting edge but do not employ in-built latches (ALE/DLE) for those DQ inputs. 20 – ns CTL deasserted pulse width for CTL inputs that signify tCTLdeassert_DQassert DQ input valid at the asserting edge but do not employ in-built latches (ALE/DLE) for those DQ inputs. 7 – ns CTL asserted pulse width for CTL inputs that signify DQ tCTLassert_DQdeassert inputs valid at the deasserting edge but do not employ in-built latches (ALE/DLE) for those DQ inputs. 7 – ns tCTLdeassert_ DQdeassert CTL deasserted pulse width for CTL inputs that signify DQ inputs valid at the deasserting edge but do not employ in-built latches (ALE/DLE) for those DQ inputs. 20 – ns tCTLassert_DQlatch CTL asserted pulse width for CTL inputs that employ in-built latches (ALE/DLE) to latch the DQ inputs. In this non-DDR case, in-built latches are always close at the deasserting edge. 7 – ns tCTLdeassert_DQlatch CTL deasserted pulse width for CTL inputs that employ in-built latches (ALE/DLE) to latch the DQ inputs. In this non-DDR case, in-built latches always close at the deasserting edge. 10 – ns tCTLassert_ DQlatchDDR CTL asserted pulse width for CTL inputs that employ in-built latches (DLE) to latch the DQ inputs in DDR mode. 10 – ns tCTLdeassert_ DQlatchDDR CTL deasserted pulse width for CTL inputs that employ in-built latches (DLE) to latch the DQ inputs in DDR mode. 10 – ns tAA DQ/CTL input to DQ output time when DQ change or CTL change needs to be detected and affects internal updates of input and output DQ lines. – 30 ns tDO CTL to data out when the CTL change merely enables the output flop update whose data was already established. – 25 ns Notes 9. All parameters guaranteed by design and validated through characterization. 10.“alpha” output corresponds to “early output” and “beta” corresponds to “delayed output”. Please refer to the GPIFII Designer Tool for the use of these outputs. Datasheet 40 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters Table 14 GPIF II timing in Asynchronous Mode[9, 10] (continued) Note The following parameters assume one state transition Parameter Description Min Max Units tOELZ CTL designated as OE to low-Z. Time when external devices should stop driving data. 0 – ns tOEHZ CTL designated as OE to high-Z 8 8 ns tCLZ CTL (non-OE) to low-Z. Time when external devices should stop driving data. 0 – ns tCHZ CTL (non-OE) to high-Z 30 30 ns tCTLalpha CTL to alpha change at output – 25 ns tCTLbeta CTL to beta change at output – 30 ns tDST Addr/data setup when DLE/ALE not used 2 – ns tDHT Addr/data hold when DLE/ALE not used 20 – ns 19.4 Slave FIFO interface 19.4.1 Synchronous Slave FIFO Read sequence description • FIFO address is stable and SLCS is asserted • FLAG indicates FIFO not empty status • SLOE is asserted. SLOE is an output-enable only, whose sole function is to drive the data bus. • SLRD is asserted The FIFO pointer is updated on the rising edge of the PCLK, while the SLRD is asserted. This starts the propagation of data from the newly addressed location to the data bus. After a propagation delay of tco (measured from the rising edge of PCLK), the new data value is present. N is the first data value read from the FIFO. To have data on the FIFO data bus, SLOE must also be asserted. The same sequence of events is applicable for a burst read. FLAG Usage: The FLAG signals are monitored for flow control by the external processor. FLAG signals are outputs from FX3 that may be configured to show empty, full, or partial status for a dedicated thread or the current thread that is addressed. Socket Switching Delay (Tssd): The socket-switching delay is measured from the time EPSWITCH# is asserted by the master, with the new socket address on the address bus, to the time the Current_Thread_DMA_Ready flag is asserted. For the Producer socket, the flag is asserted when it is ready to receive data in the DMA buffer. For the Consumer socket, the flag is asserted when it is ready to drive data out of the DMA buffer. For a synchronous slave FIFO interface, the switching delay is measured in the number of GPIF interface clock cycles; for an asynchronous slave FIFO interface, in PIB clock cycles. This is applicable only for the 5-bit Slave FIFO interface; there is no socket-switching delay in FX3’s 2-bit Slave FIFO interface, which makes use of thread switching in the GPIF™ II state machine. Note For burst mode, the SLRD# and SLOE# are asserted during the entire duration of the read. When SLOE# is asserted, the data bus is driven (with data from the previously addressed FIFO). For each subsequent rising edge of PCLK, while the SLRD# is asserted, the FIFO pointer is incremented and the next data value is placed on the data bus. Datasheet 41 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters Synchronous Read Cycle Timing t CYC PCLK tCH tCL t ACCD SLCS tAS tAH FIFO ADDR An Am t RDS tRDH SLRD SLOE Tssd t ACCD t CFLG FLAGA ( dedicated thread Flag for An ) ( 1 = Not Empty 0 = Empty ) Tssd t CFLG FLAGB (dedicated thread Flag for Am ) ( 1 = Not Empty 0 = Empty ) tOELZ Data Out tCDH tOEZ High-Z Data driven:DN (An) High-Z DN (An) tCO DN ( Am) t OEZ DN+1 (Am) DN+2 (Am) High-Z SLWR( HIGH) Figure 11 Datasheet Synchronous Slave FIFO Read Mode 42 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters 19.4.2 Synchronous Slave FIFO Write sequence description • • • • FIFO address is stable and the signal SLCS# is asserted External master or peripheral outputs the data to the data bus SLWR# is asserted While the SLWR# is asserted, data is written to the FIFO and on the rising edge of the PCLK, the FIFO pointer is incremented • The FIFO flag is updated after a delay of t WFLG from the rising edge of the clock The same sequence of events is also applicable for burst write Note For the burst mode, SLWR# and SLCS# are asserted for the entire duration, during which all the required data values are written. In this burst write mode, after the SLWR# is asserted, the data on the FIFO data bus is written to the FIFO on every rising edge of PCLK. The FIFO pointer is updated on each rising edge of PCLK. Short Packet: A short packet can be committed to the USB host by using the PKTEND#. The external device or processor should be designed to assert the PKTEND# along with the last word of data and SLWR# pulse corresponding to the last word. The FIFOADDR lines must be held constant during the PKTEND# assertion. Zero-Length Packet: The external device or processor can signal a Zero-Length Packet (ZLP) to FX3 simply by asserting PKTEND#, without asserting SLWR#. SLCS# and address must be driven as shown in Figure 12. Synchronous Write Cycle Timing tCYC PCLK tCH tCL SLCS tAS tAH Am An FIFO ADDR tWRS Tssd tWRH SLWR t CFLG tFAD FLAGA dedicated thread FLAG for An ( 1 = Not Full0 = Full) Tssd FLAGB current thread FLAG for Am ( 1 = Not Full0 = Full) Data IN tDS tDH High-Z DN(An) tFAD tDS tDH DN( Am) t CFLG tDH DN+1 (Am) DN+2 (Am) tPES tPEH PKTEND SLOE ( HIGH) Figure 12 Datasheet Synchronous Slave FIFO Write Mode 43 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters Synchronous ZLP Write Cycle Timing t CYC PCLK t CH tCL SLCS tAS tAH An FIFO ADDR SLWR (HIGH) tPES tPEH PKTEND t CFLG FLAGA dedicated thread FLAG for An (1 = Not Full 0= Full) FLAGB current thread FLAG for Am (1 = Not Full 0= Full) Data IN High-Z SLOE (HIGH) Figure 13 Datasheet Synchronous Slave FIFO ZLP Write Cycle timing 44 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters Table 15 Synchronous Slave FIFO parameters[11] Parameter Description Min Max Units FREQ Interface clock frequency – 100 MHz tCYC Clock period 10 – ns tCH Clock HIGH time 4 – ns tCL Clock LOW time 4 – ns tRDS SLRD# to CLK setup time 2 – ns tRDH SLRD# to CLK hold time 0.5 – ns tWRS SLWR# to CLK setup time 2 – ns tWRH SLWR# to CLK hold time 0.5 – ns tCO Clock to valid data – 7 ns tDS Data input setup time 2 – ns tDH CLK to data input hold 0.5 – ns tAS Address to CLK setup time 2 – ns tAH CLK to address hold time 0.5 – ns tOELZ SLOE# to data low-Z 0 – ns tCFLG CLK to flag output propagation delay – 8 ns tOEZ SLOE# deassert to Data Hi Z – 8 ns tPES PKTEND# to CLK setup 2 – ns tPEH CLK to PKTEND# hold 0.5 – ns tCDH CLK to data output hold 2 – ns tSSD Socket switching delay 2 68 Clock cycles tACCD Latency from SLRD# to Data 2 2 Clock cycles tFAD Latency from SLWR# to FLAG 3 3 Clock cycles Note Three-cycle latency from ADDR to DATA/FLAGS. Note 11.All parameters guaranteed by design and validated through characterization. Datasheet 45 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters 19.4.3 Asynchronous Slave FIFO Read sequence description • FIFO address is stable and the SLCS# signal is asserted. • SLOE# is asserted. This results in driving the data bus. • SLRD # is asserted. • Data from the FIFO is driven after assertion of SLRD#. This data is valid after a propagation delay of tRDO from the falling edge of SLRD#. • FIFO pointer is incremented on deassertion of SLRD# In Figure 14, data N is the first valid data read from the FIFO. For data to appear on the data bus during the read cycle, SLOE# must be in an asserted state. SLRD# and SLOE# can also be tied. The same sequence of events is also shown for a burst read. Note In the burst read mode, during SLOE# assertion, the data bus is in a driven state (data is driven from a previously addressed FIFO). After assertion of SLRD# data from the FIFO is driven on the data bus (SLOE# must also be asserted). The FIFO pointer is incremented after deassertion of SLRD#. Asynchronous Read Cycle Timing SLCS tAS tAH An FIFO ADDR tRDl Am tRDh SLRD SLOE tFLG tRFLG FLAGA dedicated thread Flag for An (1=Not empty 0 = Empty) FLAGB dedicated thread Flag for Am (1=Not empty 0 = Empty) tOE tRDO tOH tOE tRDO tRDO tOH tLZ Data Out High-Z DN(An) DN(An) DN(Am) DN+1(Am) DN+2(Am) SLWR (HIGH) Figure 14 Datasheet Asynchronous Slave FIFO Read Mode 46 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters 19.4.4 Asynchronous Slave FIFO Write sequence description • FIFO address is driven and SLCS# is asserted • SLWR# is asserted. SLCS# must be asserted with SLWR# or before SLWR# is asserted • Data must be present on the tWRS bus before the deasserting edge of SLWR# • Deassertion of SLWR# causes the data to be written from the data bus to the FIFO, and then the FIFO pointer is incremented • The FIFO flag is updated after the tWFLG from the deasserting edge of SLWR. The same sequence of events is shown for a burst write. Note that in the burst write mode, after SLWR# deassertion, the data is written to the FIFO, and then the FIFO pointer is incremented. Short Packet: A short packet can be committed to the USB host by using the PKTEND#. The external device or processor should be designed to assert the PKTEND# along with the last word of data and SLWR# pulse corresponding to the last word. The FIFOADDR lines must be held constant during the PKTEND# assertion. Zero-Length Packet: The external device or processor can signal a zero-length packet (ZLP) to FX3 simply by asserting PKTEND#, without asserting SLWR#. SLCS# and the address must be driven as shown in Figure 16. FLAG Usage: The FLAG signals are monitored by the external processor for flow control. FLAG signals are FX3 outputs that can be configured to show empty, full, and partial status for a dedicated address or the current address. SLCS tAS tAH An FIFO ADDR tWRl Am tWRh SLWR tFLG t WFLG FLAGA dedicated thread Flag for An (1= Not Full 0 = Full) t WFLG FLAGB dedicated thread Flag for Am (1= Not Full 0 = Full) DATA In tWR S High-Z tWR tWRH S t WRH DN (Am) DN (An) DN+1 (Am) DN+2 (Am) t WRPE t PEh PKTEND SLOE ( HIGH) Figure 15 Datasheet Asynchronous Slave FIFO Write Mode 47 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters SLCS tAS tAH An FIFO ADDR SLWR ( HIGH) tPEl tPEh PKTEND t WFLG FLAGA dedicated thread Flag for An (1= Not Full 0 = Full) FLAGB dedicated thread Flag for Am (1= Not Full 0 = Full) DATA In High-Z SLOE ( HIGH) Figure 16 Datasheet Asynchronous ZLP Write Cycle timing 48 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters Table 16 Asynchronous Slave FIFO parameters[12] Parameter Description Min Max Units tRDI SLRD# LOW 20 – ns tRDh SLRD# HIGH 10 – ns tAS Address to SLRD#/SLWR# setup time 7 – ns tAH SLRD#/SLWR#/PKTEND to address hold time 2 – ns tRFLG SLRD# to FLAGS output propagation delay – 35 ns tFLG ADDR to FLAGS output propagation delay – 22.5 ns tRDO SLRD# to data valid – 25 ns tOE OE# low to data valid – 25 ns tLZ OE# low to data low-Z 0 – ns tOH SLOE# deassert data output hold – 22.5 ns tWRI SLWR# LOW 20 – ns tWRh SLWR# HIGH 10 – ns tWRS Data to SLWR# setup time 7 – ns tWRH SLWR# to Data Hold time 2 – ns tWFLG SLWR#/PKTEND to Flags output propagation delay – 35 ns tPEI PKTEND LOW 20 – ns tPEh PKTEND HIGH 7.5 – ns tWRPE SLWR# deassert to PKTEND deassert 2 – ns Note 12.All parameters guaranteed by design and validated through characterization. Datasheet 49 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters 19.5 Host Processor Interface (P-Port) timing 19.5.1 Asynchronous SRAM timing Socket Read – Address Transition Controlled timing (OE# is asserted) A[0] tAA tAH tOH DATA OUT HIGH IMPEDANCE DATA VALID DATA VALID DATA VALID tOE OE# OE# Controlled timing ADDRESS WE# (HIGH) tAOS CE# tOHC tRC OE# tOHH tOE tOEZ tOLZ DATA OUT Figure 17 Datasheet HIGH IMPEDANCE DATA VALID HIGH IMPEDANCE DATA VALID HIGH IMPEDANCE Non-multiplexed Asynchronous SRAM Read timing 50 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters Write Cycle 1 WE# Controlled, OE# HIGH during Write tWC ADDRESS tCW CE# tAW tAH tWP WE# tAS tWPH OE# tDS DATA I/O tDH VALID DATA VALID DATA tWHZ Write Cycle 2 CE# Controlled, OE# HIGH during Write tWC ADDRESS tAS tCW tCPH CE# tAW tAH tWP WE# OE# tDS DATA I/O tDH VALID DATA VALID DATA tWHZ Figure 18 Datasheet Non-multiplexed Asynchronous SRAM Write timing (WE# and CE# Controlled) 51 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters Write Cycle 3 WE# Controlled. OE# LOW tWC tCW CE# tAW tAH tAS tWP WE# tDS DATA I/O tDH VALID DATA tOW tWHZ Note: tWP must be adjusted such that tWP > tWHZ + tDS Figure 19 Datasheet Non-multiplexed Asynchronous SRAM Write timing (WE# Controlled, OE# LOW) 52 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters Table 17 Asynchronous SRAM timing parameters[13] Parameter Description Min Max Units – 61.5 Mbps 32.5 – ns – SRAM interface bandwidth tRC Read cycle time tAA Address to data valid – 30 ns tAOS Address to OE# LOW setup time 7 – ns tOH Data output hold from address change 3 – ns tOHH OE# HIGH hold time 7.5 – ns tOHC OE# HIGH to CE# HIGH 2 – ns tOE OE# LOW to data valid – 25 ns tOLZ OE# LOW to Low-Z 0 – ns tWC Write cycle time 30 – ns tCW CE# LOW to write end 30 – ns tAW Address valid to write end 30 – ns tAS Address setup to write start 7 – ns tAH Address hold time from CE# or WE# 2 – ns tWP WE# pulse width 20 – ns tWPH WE# HIGH time 10 – ns tCPH CE# HIGH time 10 – ns tDS Data setup to write end 7 – ns tDH Data hold to write end 2 – ns tWHZ Write to DQ High-Z output – 22.5 ns tOEZ OE# HIGH to DQ High-Z output – 22.5 ns tOW End of write to Low-Z output 0 – ns Note 13.All parameters guaranteed by design and validated through characterization. Datasheet 53 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters 19.5.2 ADMux timing for Asynchronous Access tRC tACC Valid Address A[0:7]/DQ[0:15] tAVS tAVH tVP ADV# WE# (HIGH) Valid Addr Valid Data tCEAV tHZ tCO CE# tCPH tHZ tOLZ tOE OE# tAVOE Note: 1. Multiple read cycles can be executed while keeping CE# low. 2. Read operation ends with either de-assertion of either OE# or CE#, whichever comes earlier. Figure 20 ADMux Asynchronous Random Read tWC Address Valid A[0:7]/DQ[0:15] Valid Addr Data Valid tAW tAVS ADV# tCEAV CE# tAVH tDS tDH tVPH tVP tCPH tCW WE# tWP tWPH tAVWE Note: 1. Multiple write cycles can be executed while keeping CE# low. 2. Write operation ends with de-assertion of either WE# or CE#, whichever comes earlier. Figure 21 Datasheet ADMux Asynchronous Random Write 54 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters Table 18 Parameter Asynchronous ADMux timing parameters[14] Description Min Max Units Notes 54.5 – ns This parameter is dependent on when the P-port processors deasserts OE# ADMux Asynchronous READ Access timing parameters tRC Read cycle time (address valid to address valid) tACC Address valid to data valid – 32 ns – tCO CE# assert to data valid – 34.5 ns – tAVOE ADV# deassert to OE# assert 2 – ns – tOLZ OE# assert to data Low-Z 0 – ns – tOE OE# assert to data valid – 25 ns – tHZ Read cycle end to data High-Z – 22.5 ns – ADMux Asynchronous WRITE Access timing parameters tWC Write cycle time (Address Valid to Address Valid) – 52.5 ns – tAW Address valid to write end 30 – ns – tCW CE# assert to write end 30 – ns – tAVWE ADV# deassert to WE# assert 2 – ns – tWP WE# LOW pulse width 20 – ns – tWPH WE# HIGH pulse width 10 – ns – tDS Data valid setup to WE# deassert 18 – ns – tDH Data valid hold from WE# deassert 2 – ns – ADMux Asynchronous Common READ/WRITE Access timing parameters tAVS Address valid setup to ADV# deassert 5 – ns – tAVH Address valid hold from ADV# deassert 2 – ns – tVP ADV# LOW pulse width 7.5 – ns – tCPH CE# HIGH pulse width 10 – ns – tVPH ADV# HIGH pulse width 15 – ns – tCEAV CE# assert to ADV# assert 0 – ns – Note 14.All parameters guaranteed by design and validated through characterization. Datasheet 55 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters 19.5.3 Synchronous ADMux timing tCLK 2- cycle latency from OE# to DATA tCLKH tCLKL CLK tCO tS A[0:7]/DQ[0:31] tH Valid Data Valid Address tS tH ADV# tOHZ tS CE# tAVOE tOLZ OE# tKW tKW RDY tCH WE# (HIGH) Note: 1) External P-Port processor and FX3 operate on the same clock edge 2) External processor sees RDY assert 2 cycles after OE # asserts andand sees RDY deassert a cycle after the data appears on the output 3) Valid output data appears 2 cycle after OE # asserted. The data is held until OE # deasserts 4) Two cycle latency is shown for 0-100 MHz operation. Latency can be reduced by 1 cycle for operations at less than 50 MHz (this 1 cycle latency is not supported by the bootloader) Figure 22 Synchronous ADMux Interface – Read Cycle timing 2-cycle latency between WE# and data being latched 2-cycle latency between this clk edge and RDY deassertion seen by the host CLK tCLK tS A[0:7]/DQ[0:31] tDS tH Valid Address tS tDH Valid Data tH ADV# tS CE# tAVWE tS tH WE# tKW RDY tKW Note: 1) External P-Port processor and FX3 operate on the same clock edge 2) External processor sees RDY assert 2 cycles after WE # asserts and deassert 3 cycles after the edge sampling the data. 3) Two cycle latency is shown for 0-100 MHz operation. Latency can be reduced by 1 cycle for operations at less than 50 MHz (this 1 cycle latency is not supported by the bootloader ) Figure 23 Datasheet Synchronous ADMux Interface – Write Cycle timing 56 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters 2-cycle latency from OE# to Data tCLK tCLKH tCLKL CLK tCO tS A[0:7]/DQ[0:31] tCH tH Valid Address tS D0 D1 D2 D3 tH ADV# tHZ tS CE# tAVOE tOLZ OE# tKW tKW RDY Note: 1) External P-Port processor and FX3 work operate on the same clock edge 2) External processor sees RDY assert 2 cycles after OE # asserts andand sees RDY deassert a cycle after the last burst data appears on the output 3) Valid output data appears 2 cycle after OE # asserted. The last burst data is held until OE # deasserts 4) Burst size of 4 is shown. Transfer size for the operation must be a multiple of burst size. Burst size is usually power of 2. RDY will not deassert in the middle of the burst. 5) External processor cannot deassert OE in the middle of a burst. If it does so, any bytes remaining in the burst packet could get lost. 6) Two cycle latency is shown for 0-100 MHz operation. Latency can be reduced by 1 cycle for operations at less than 50 MHz (this 1 cycle latency is not supported by the bootloader) Figure 24 Synchronous ADMux Interface – Burst Read timing 2-cycle latency between WE# and data being latched tCLKH 2-cycle latency between this clk edge and RDY deassertion seen by the host tCLKL CLK tCLK tS A[0:7]/DQ[0:31] tDS tH D0 Valid Address tS tDH tDH D1 D2 D3 tH ADV# tS CE# tAVWE WE# RDY tKW tKW Note: 1) External P-Port processor and FX3 operate on the same clock edge 2) External processor sees RDY assert 2 cycles after WE # asserts and deasserts 3 cycles after the edge sampling the last burst data. 3) Transfer size for the operation must be a multiple of burst size. Burst size is usually power of 2. RDY will not deassert in the middle of the burst. Burst size of 4 is shown 4) External processor cannot deassert WE in the middle of a burst. If it does so, any bytes remaining in the burst packet could get lost. 5)Two cycle latency is shown for 0-100 MHz operation. Latency can be reduced by 1 cycle for operations at less than 50 MHz (this 1 cycle latency is not supported by the bootloader) Figure 25 Datasheet Sync ADMux Interface – Burst Write timing 57 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters Table 19 Synchronous ADMux timing parameters[15] Parameter Description Min Max Unit FREQ Interface clock frequency – 100 MHz tCLK Clock period 10 – ns tCLKH Clock HIGH time 4 – ns tCLKL Clock LOW time 4 – ns tS CE#/WE#/DQ setup time 2 – ns tH CE#/WE#/DQ hold time 0.5 – ns tCH Clock to data output hold time 0 – ns tDS Data input setup time 2 – ns tDH Clock to data input hold 0.5 – ns tAVDOE ADV# HIGH to OE# LOW 0 – ns tAVDWE ADV# HIGH to WE# LOW 0 – ns tHZ CE# HIGH to Data High-Z – 8 ns tOHZ OE# HIGH to Data High-Z – 8 ns tOLZ OE# LOW to Data Low-Z 0 – ns tKW Clock to RDY valid – 8 ns Note 15.All parameters guaranteed by design and validated through characterization. Datasheet 58 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters 19.6 Serial Peripherals timing 19.6.1 I2C timing Figure 26 I2C timing definition Datasheet 59 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters Table 20 I2C timing parameters[16] Parameter Description Min Max Units I2C Standard Mode parameters fSCL SCL clock frequency 0 100 kHz tHD:STA Hold time START condition 4 – µs tLOW LOW period of the SCL 4.7 – µs tHIGH HIGH period of the SCL 4 – µs tSU:STA Setup time for a repeated START condition 4.7 – µs tHD:DAT Data hold time 0 – µs tSU:DAT Data setup time 250 – ns tr Rise time of both SDA and SCL signals – 1000 ns tf Fall time of both SDA and SCL signals – 300 ns tSU:STO Setup time for STOP condition 4 – µs tBUF Bus free time between a STOP and START condition 4.7 – µs tVD:DAT Data valid time – 3.45 µs tVD:ACK Data valid ACK – 3.45 µs tSP Pulse width of spikes that must be suppressed by input filter n/a n/a 0 400 kHz 2 I C Fast Mode parameters fSCL SCL clock frequency tHD:STA Hold time START condition 0.6 – µs tLOW LOW period of the SCL 1.3 – µs tHIGH HIGH period of the SCL 0.6 – µs tSU:STA Setup time for a repeated START condition 0.6 – µs tHD:DAT Data hold time 0 – µs tSU:DAT Data setup time 100 – ns tr Rise time of both SDA and SCL signals – 300 ns tf Fall time of both SDA and SCL signals – 300 ns tSU:STO Setup time for STOP condition 0.6 – µs tBUF Bus free time between a STOP and START condition 1.3 – µs tVD:DAT Data valid time – 0.9 µs tVD:ACK Data valid ACK – 0.9 µs tSP Pulse width of spikes that must be suppressed by input filter 0 50 ns Note 16.All parameters guaranteed by design and validated through characterization. Datasheet 60 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters Table 20 I2C timing parameters[16] (continued) Parameter Description Min Max Units 0 1000 kHz I2C Fast Mode Plus Parameters (Not supported at I2C_VDDQ = 1.2 V) fSCL SCL clock frequency tHD:STA Hold time START condition 0.26 – µs tLOW LOW period of the SCL 0.5 – µs tHIGH HIGH period of the SCL 0.26 – µs tSU:STA Setup time for a repeated START condition 0.26 – µs tHD:DAT Data hold time 0 – µs tSU:DAT Data setup time 50 – ns tr Rise time of both SDA and SCL signals – 120 ns tf Fall time of both SDA and SCL signals – 120 ns tSU:STO Setup time for STOP condition 0.26 – µs tBUF Bus-free time between a STOP and START condition 0.5 – µs tVD:DAT Data valid time – 0.45 µs tVD:ACK Data valid ACK – 0.55 µs tSP Pulse width of spikes that must be suppressed by input filter 0 50 ns Datasheet 61 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters 19.6.2 I2S timing diagram tT tTR tTF tTL tTH SCK tThd SA, WS (output) tTd Figure 27 I2S transmit cycle Table 21 I2S timing parameters[17] Parameter Description Min Max Units tT I2S transmitter clock cycle Ttr – ns tTL I2S transmitter cycle LOW period 0.35 × Ttr – ns tTH I2S transmitter cycle HIGH period 0.35 × Ttr – ns tTR I2S transmitter rise time – 0.15 × Ttr ns tTF I2S transmitter fall time – 0.15 × Ttr ns tThd I2S transmitter data hold time 0 – ns – 0.8tT ns tTd 2 I S transmitter delay time Note tT is selectable through clock gears. Max Ttr is designed for 96-kHz codec at 32 bits to be 326 ns (3.072 MHz). Note 17.All parameters guaranteed by design and validated through characterization. Datasheet 62 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters 19.6.3 SPI timing specification SSN (output) tlead SCK (CPOL=0, Output) tsdi MISO (input) twsck thoi MSB LSB td tsdd tdis tdi v MOSI (output) tlag trf twsck SCK (CPOL=1, Output) tssnh tsck LSB MSB SPI Master Timing for CPHA = 0 SSN (output) SCK (CPOL=0, Output) tssnh tsck tlead twsck trf tlag twsck SCK (CPOL=1, Output) tsdi MISO (input) thoi LSB tdis tdi tdv MOSI (output) MSB LSB MSB SPI Master Timing for CPHA = 1 Figure 28 Datasheet SPI timing 63 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters Table 22 SPI timing parameters[18] Parameter Description Min Max Units fop Operating frequency 0 33 MHz tsck Cycle time 30 – ns twsck Clock high/low time 13.5 – ns SSN-SCK lead time 1/2 tsck[19] – 5 1.5 tsck[19] + 5 ns tlead 0.5 1.5 tsck [19] +5 ns tlag Enable lag time trf Rise/fall time – 8 ns tsdd Output SSN to valid data delay time – 5 ns tdv Output data valid time – 5 ns tdi Output data invalid 0 – ns tssnh Minimum SSN high time 10 – ns tsdi Data setup time input 8 – ns thoi Data hold time input 0 – ns tdis Disable data output on SSN high 0 – ns Notes 18.All parameters guaranteed by design and validated through characterization. 19.Depends on LAG and LEAD setting in the SPI_CONFIG register. Datasheet 64 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller AC timing parameters 19.7 Reset sequence FX3’s hard reset sequence requirements are specified in this section. Table 23 Reset and Standby timing parameters Parameter Definition Conditions tRPW Minimum RESET# pulse width tRH Minimum HIGH on RESET# tRR Reset recovery time (after which Boot loader begins firmware download) tSBY Time to enter standby/suspend (from the time MAIN_CLOCK_EN/ MAIN_POWER_EN bit is set) tWU Time to wakeup from standby tWH Minimum time before Standby/Suspend source may be reasserted Min (ms) Max (ms) Clock input 1 – Crystal input 1 – – 5 – Clock input 1 – Crystal input 5 – – 1 Clock input 1 – Crystal input 5 – – 5 – VDD ( core ) xVDDQ XTALIN/ CLKIN XTALIN/ CLKIN must be stable before exiting Standby/Suspend Mandatory Reset Pulse tRh tRR Hard Reset RESET # tWH tRPW tSBY Standby/ Suspend Source Standby/Suspend source Is asserted (MAIN_POWER_EN/ MAIN_CLK_EN bit is set) Figure 29 Datasheet tWU Standby/Suspend source Is deasserted Reset sequence 65 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Package diagram 20 Package diagram 2X 0.10 C E1 E B A 11 10 9 8 7 6 5 (datum B) 4 3 2 A1 CORNER 1 7 A1 CORNER A B C D 6 E SD D1 F D (datum A) G H J K eD 0.10 C 2X L 6 eE SE TOP VIEW BOTTOM VIEW 0.20 C DETAIL A A1 0.08 C C 121XØb 5 A Ø0.15 M C A B Ø0.08 M C SIDE VIEW DETAIL A NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETERS. DIMENSIONS SYMBOL MIN. NOM. MAX. A - - 1.20 A1 0.15 - - D 10.00 BSC E 10.00 BSC D1 8.00 BSC E1 8.00 BSC MD 11 ME 11 N 121 b eD eE SD SE 0.25 0.30 2. SOLDER BALL POSITION DESIGNATION PER JEP95, SECTION 3, SPP-020. 3. "e" REPRESENTS THE SOLDER BALL GRID PITCH. 4. SYMBOL "MD" IS THE BALL MATRIX SIZE IN THE "D" DIRECTION. SYMBOL "ME" IS THE BALL MATRIX SIZE IN THE "E" DIRECTION. N IS THE NUMBER OF POPULATED SOLDER BALL POSITIONS FOR MATRIX SIZE MD X ME. 5. DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL DIAMETER IN A PLANE PARALLEL TO DATUM C. 6. "SD" AND "SE" ARE MEASURED WITH RESPECT TO DATUMS A AND B AND DEFINE THE POSITION OF THE CENTER SOLDER BALL IN THE OUTER ROW. 0.35 0.80 BSC 0.80 BSC 0.00 0.00 WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN THE OUTER ROW, "SD" OR "SE" = 0. WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN THE OUTER ROW, "SD" = eD/2 AND "SE" = eE/2. 7. A1 CORNER TO BE IDENTIFIED BY CHAMFER, LASER OR INK MARK METALIZED MARK, INDENTATION OR OTHER MEANS. 8. "+" INDICATES THE THEORETICAL CENTER OF DEPOPULATED SOLDER BALLS. CYPRESS Company Confidential 001-54471 *F THIS DRAWING CONTAINS INFORMATION WHICH IS THE PROPRIETARY PROPERTY OF CYPRESS SEMICONDUCTOR CORPORATION. THIS DRAWING IS RECEIVED IN CONFIDENCE AND ITS CONTENTS MAY NOT BE DISCLOSED WITHOUT WRITTEN CONSENT OF CYPRESS SEMICONDUCTOR CORPORATION. Figure 30 Datasheet DRAWN BY PACKAGE CODE(S) BK0AA FBI121 T4A121 KOTA APPROVED BY GSHN DATE 28-JUN-17 TITLE PACKAGE OUTLINE, 121 BALL FBGA 10.0X10.0X1.2 MM BK0AA/FBI121/T4A121 SPEC NO. DATE 28-JUN-17 SCALE : TO FIT REV 001-54471 *F SHEET 1 OF 2 121-ball BGA package diagram 66 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Ordering information 21 Ordering information Table 24 Ordering information USB SRAM (kB) GPIF II data bus width Operating temperature CYUSB3011-BZXC USB 3.0 256 16-bit 0°C to +70°C 121-ball BGA CYUSB3012-BZXC USB 3.0 256 32-bit 0°C to +70°C 121-ball BGA CYUSB3013-BZXC USB 3.0 512 16-bit 0°C to +70°C 121-ball BGA CYUSB3014-BZXC USB 3.0 512 32-bit 0°C to +70°C 121-ball BGA CYUSB3014-BZXI USB 3.0 512 32-bit –40°C to +85°C 121-ball BGA CYUSB2014-BZXC USB 2.0 512 32-bit 0°C to +70°C 121-ball BGA CYUSB2014-BZXI USB 2.0 512 32-bit –40°C to +85°C 121-ball BGA Ordering code 21.1 Datasheet Package type Ordering code definitions 67 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Acronyms 22 Acronyms Table 25 Acronyms Acronym Description DMA direct memory access FIFO first in, first out GPIF general programmable interface HNP host negotiation protocol 2 inter-integrated circuit 2 IS inter IC sound MISO master in, slave out MOSI master out, slave in MMC multimedia card MSC mass storage class MTP media transfer protocol OTG on-the-go OVP overvoltage protection PHY physical layer PLL phase locked loop PMIC power management IC PVT process voltage temperature RTOS real-time operating system SCL serial clock line SCLK serial clock SD secure digital SD secure digital SDA serial data clock SDIO secure digital input / output SLC single-level cell SLCS Slave Chip Select SLOE Slave Output Enable SLRD Slave Read SLWR Slave Write SPI serial peripheral interface SRP session request protocol SSN SPI slave select (Active low) UART universal asynchronous receiver transmitter UVC USB Video Class USB universal serial bus IC Datasheet 68 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Document conventions 23 Document conventions 23.1 Units of measure Table 26 Units of measure Symbol Unit of measure °C degree Celsius µA microamperes µs microseconds mA milliamperes Mbps Megabits per second MBps Megabytes per second MHz mega hertz ms milliseconds ns nanoseconds  ohms pF pico Farad V volts Datasheet 69 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Errata 24 Errata This section describes the errata for Revision D, C and B of the FX3. Details include errata trigger conditions, scope of impact, available workaround, and silicon revision applicability. Contact your local Infineon Sales Representative if you have questions. Part numbers affected Part number Device characteristics CYUSB301x-xxxx All variants CYUSB201x-xxxx All variants 24.1 Qualification status Product Status: Production 24.2 Errata summary The following table defines the errata applicability to available Rev. D EZ-USB FX3 SuperSpeed USB Controller family devices. Part number Silicon Revision 1. Turning off VIO1 during Normal, Suspend, and Standby modes causes the FX3 to stop working. CYUSB301x-xxxx CYUSB201x-xxxx Rev. D, C, B Workaround provided 2. USB enumeration failure in USB boot mode when FX3 is self-powered. CYUSB301x-xxxx CYUSB201x-xxxx Rev. D, C, B Workaround provided 3. Extra ZLP is generated by the COMMIT action in the GPIF II state. CYUSB301x-xxxx CYUSB201x-xxxx Rev. D, C, B Workaround provided 4. Invalid PID Sequence in USB 2.0 ISOC data transfer. CYUSB301x-xxxx CYUSB201x-xxxx Rev. D, C, B Workaround provided 5. USB data transfer errors are seen when ZLP is followed by data packet within same microframe. CYUSB301x-xxxx CYUSB201x-xxxx Rev. D, C, B Workaround provided 6. Bus collision is seen when the I2C block is used as a master in the I2C Multi-master configuration. CYUSB301x-xxxx CYUSB201x-xxxx Use FX3 in Rev. D, C, B single-master configuration 7. Low Power U1 Fast-Exit Issue with USB3.0 host controller. CYUSB301x-xxxx Rev. D, C, B Workaround provided 8. USB data corruption when operating on hosts with poor link quality. CYUSB301x-xxxx Rev. D, C, B Workaround provided 9. Device treats Rx Detect sequence from the USB 3.0 host as a valid U1 exit LFPS burst. CYUSB301x-xxxx Rev. D, C, B Workaround provided 10. I2C Data Valid (tVD:DAT) specification violation at 400 kHz with a 40/60 duty cycle. CYUSB301x-xxxx CYUSB201x-xxxx No Rev. D, C, B workaround needed 11. FX3 Device does not respond correctly to Port Capability Request from Host after multiple power cycles. CYUSB301x-xxxx Rev. D, C, B Items Datasheet 70 Fix status Workaround provided 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Errata 1. Turning off VIO1 during Normal, Suspend, and Standby modes causes the FX3 to stop working. Problem definition Turning off the VIO1 during Normal, Suspend, and Standby modes will cause the FX3 to stop working. Parameters affected NA Trigger condition(s) This condition is triggered when the VIO1 is turned off during Normal, Suspend, and Standby modes. Scope of impact FX3 stops working. Workaround VIO1 must stay on during Normal, Suspend, and Standby modes. Fix status No fix. Workaround is required. 2.USB enumeration failure in USB boot mode when FX3 is self-powered. Problem definition When FX3 is self-powered and not connected to the USB host, it enters low-power mode and does not wake up when connected to USB host afterwards. This is because the bootloader does not check the VBUS pin on the connector to detect USB connection. It expects that the USB bus is connected to the host when it is powered on. Parameters affected NA Trigger condition(s) This condition is triggered when FX3 is self-powered in USB boot mode. Scope of impact Device does not enumerate Workaround Reset the device after connecting to USB host. Fix status No fix. Workaround is required. 3.Extra ZLP is generated by the COMMIT action in the GPIF II state. Problem definition When COMMIT action is used in a GPIF-II state without IN_DATA action then an extra zero length packet (ZLP) is committed along with the data packets. Parameters affected NA Trigger condition(s) This condition is triggered when COMMIT action is used in a state without IN_DATA action. Scope of impact Extra ZLP is generated. Workaround Use IN_DATA action along with COMMIT action in the same state. Fix status No fix. Workaround is required. Datasheet 71 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Errata 4.Invalid PID Sequence in USB 2.0 ISOC data transfer. Problem definition When the FX3 device is functioning as a high speed USB device with high bandwidth isochronous endpoints, the PID sequence of the ISO data packets is governed solely by the isomult setting. The length of the data packet is not considered while generating the PID sequence during each microframe. For example, even if a short packet is being sent on an endpoint with MULT set to 2; the PID used will be DATA2. Parameters affected NA Trigger condition(s) This condition is triggered when high bandwidth ISOC transfer endpoints are used. Scope of impact ISOC data transfers failure. Workaround This problem can be worked around by reconfiguring the endpoint with a lower isomult setting prior to sending short packets, and then switching back to the original value. Fix status No fix. Workaround is required. 5.USB data transfer errors are seen when ZLP is followed by data packet within same microframe. Problem definition Some data transfer errors may be seen if a ZLP is followed very quickly (within one microframe or 125 µs) by another data packet on a burst enabled USB IN endpoint operating at super speed. Parameters affected NA Trigger condition(s) This condition is triggered in SuperSpeed transfer with ZLPs Scope of impact Data failure and lower data speed. Workaround The solution is to ensure that some time is allowed to elapse between a ZLP and the next data packet on burst enabled USB IN endpoints. If this cannot be ensured at the data source, the CyU3PDmaChannelSetSuspend() API can be used to suspend the corresponding USB DMA socket on seeing the EOP condition. The channel operation can then be resumed as soon as the suspend callback is received. Fix status No fix. Workaround is required. 6.Bus collision is seen when the I2C block is used as a master in the I2C Multi-master configuration. Problem definition When FX3 is used as a master in the I2C multi-master configuration, there can be occasional bus collisions. Parameters affected NA Trigger condition(s) This condition is triggered only when the FX3 I2C block operates in Multi-master configuration. Scope of impact The FX3 I2C block can transmit data when the I2C bus is not idle leading to bus collision. Workaround Use FX3 as a single master. Fix status No fix. Datasheet 72 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Errata 7.Low Power U1 Fast-Exit Issue with USB3.0 host controller. Problem definition When FX3 device transitions from Low power U1 state to U0 state within 5 µs after entering U1 state, the device sometimes fails to transition back to U0 state, resulting in USB Reset. Parameters affected NA Trigger condition(s) This condition is triggered during low power transition mode. Scope of impact Unexpected USB warm reset during data transfer. Workaround This problem can be worked around in the FW by disabling LPM (Link Power Management) during data transfer. Fix status FW workaround is proven and reliable. 8.USB data corruption when operating on hosts with poor link quality. Problem definition If FX3 is operating on a USB 3.0 link with poor signal quality, the device could send corrupted data on any of the IN endpoints (including the control endpoint). Parameters affected NA Trigger condition(s) This condition is triggered when the USB3.0 link signal quality is very poor. Scope of impact Data corruption in any of the IN endpoints (including the control endpoint). Workaround The application firmware should perform an error recovery by stalling the endpoint on receiving CYU3P_USBEPSS_RESET_EVT event, and then stop and restart DMA path when the CLEAR_FEATURE request is received. Note: SDK versions 1.3.3 and above internally manages the DMA transfers and performs the endpoint reset when potential error conditions are seen. For more details in application firmware, please refer to GpiftoUsb example available with SDK. Fix status FW Work-around is proven and reliable. 9.Device treats Rx Detect sequence from the USB 3.0 host as a valid U1 exit LFPS burst. Problem definition The USB 3.0 PHY in the FX3 device uses an electrical idle detector to determine whether LFPS is being received. The duration for which the receiver does not see an electrical idle condition is timed to detect various LFPS bursts. This implementation causes the device to treat an Rx Detect sequence from the USB host as a valid U1 exit LFPS burst. Parameters affected NA Trigger condition(s) This condition is triggered when the USB host is initiating an Rx Detect sequence while the USB 3.0 Link State Machine on the FX3 is in the U1 state. Since the host will only perform Rx Detect sequence in the RX Detect and U2 states, the error condition is seen only in cases where the USB link on the host has moved into the U2 state while the link on FX3 is in the U1 state. Scope of impact FX3 moves into Recovery prematurely leading to a Recovery failure followed by Warm Reset and USB re-enumeration. This sequence can repeat multiple times resulting in data transfer failures. Workaround FX3 can be configured to transition from U1 to U2 a few microseconds before the host does so. This will ensure that the link will be in U2 on the device side before the host attempts any Rx Detect sequence; thereby preventing a false detection of U1 exit. Fix status Workaround is implemented in FX3 SDK library 1.3.4 and above. Datasheet 73 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Errata 10. I2C Data Valid (tVD:DAT) specification violation at 400 kHz with a 40/60 duty cycle. Problem definition I2C Data Valid (tVD:DAT) parameter at 400 kHz with a 40/60 duty cycle is 1.0625 µs, which exceeds the I2C specification limit of 0.9 µs. Parameters affected NA Trigger condition(s) This violation occurs only at 400 kHz with a 40/60 duty cycle of the I2C clock. Scope of impact Setup time (tSUDAT) is met with a huge margin for the transmitted data for 400 kHz and so tvd:DAT violation will not cause any data integrity issues. Workaround No workaround needed. Fix status No fix needed. 11.FX3 Device does not respond correctly to Port Capability Request from Host after multiple power cycles. Problem definition During multiple power cycles, sometimes the FX3 device does not respond correctly to the Port Capability request (Link Packet) from the USB Controller. In view of this, FX3 does not get the subsequent Port Configuration request from the USB controller, resulting in SS.Disabled state. The device fails to recover from this state and finally results in enumeration failure. Parameters affected NA Trigger condition(s) This condition is triggered when the FX3 provides an incorrect response to the Port Capability request from the host. Scope of impact Device fails to enumerate after multiple retries. Workaround Since the host does not send the Port Configuration request to the FX3 device, it causes a Port Configuration request timeout interrupt to be triggered in the device. This interrupt is handled in the FX3 SDK 1.3.4 onwards to generate and signal CY_U3P_USB_EVENT_LMP_EXCH_FAIL event to the application. This event should be handled in the user application such that it does a USB Interface Block Restart. Refer the Knowledge Base Article (KBA225778) for more details and the firmware workaround example project. Fix status Suggested firmware work-around is proven and reliable. Datasheet 74 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Revision history Revision histor y Document revision Date ** 2009-03-06 New data sheet. 2009-09-01 Updated the part# from CYX01XXBB to CYUSB3011-BZXI Changed status from “ADVANCE” to “ADVANCE INFORMATION” In page 1, the second bullet (Flexible Host Interface), add “32-bit, 100 MHz” to first sub bullet. In page 1, changed the second bullet “Flexible Host Interface” to General Programmable Interface”. In page 1, the second bullet (Flexible Host Interface), removed “DMA Slave Support” and “MMC Slave support with Pass through Boot” sub bullets. In page 1, third bullet, changed “50 A with Core Power” to “60 A with Core Power” In page 1, fifth bullet, added “at 1 MHz” In page 1, seventh bullet, added “up to 4 MHz” to UART In page 1, Applications Section, move “Digital Still Cameras” to second line. In page 1, Applications Section, added “Machine Vision” and Industrial Cameras” Added ™ to GPIF and FX3. In page 1, updated Logic Block Diagram. In page 2, section of “Functional Overview”, updated the whole section. In page 2, removed the section of “Product Interface” In page 2, removed the section of “Processor Interface (P-Port)” In page 2, removed the section of “USB Interface (U-Port)” In page 2, removed the section of “Other Interfaces” In page 2, added a section of “GPIF II” In page 2, added a section of “CPU” In page 2, added a section of “JTAG Interface” In page 2, added a section of “Boot Options” In page 2, added a section of “ReNumeration” In page 2, added a section of “Power” In the section of “Package”, replaced “West Bridge USB 3.0 Platform” by FX3. In the section of “Package”, added 0.8 mm pitch in front of BGA. Added Pin List (Table 1) *B 2009-09-29 Changed title to EZ-USB™ FX3: SuperSpeed USB Controller Features: Added the thrid bullet “Fully accessible 32-bit ARM9 core with 512kB of embedded SRAM” Added the thrid line “EZ USB™ Software and DVK for easy code development” Table 1: Pin 74, corrected to NC - No Connect. *C 2009-12-08 Added data sheet to the USB 3.0 EROS spec 001-51884. No technical updates. *A Datasheet Description of changes 75 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Revision history Document revision Date Description of changes 2010-11-08 Changed status from Advance to Preliminary. Changed part number from CYUSB3011 to CYUSB3014 Added the following sections: Power, Digital I/Os, Digital I/Os, System-level ESD, DC specifications, AC timing parameters, Reset sequence, Package diagram Added DC specifications table Updated feature list Updated Pin List Added support for selectable clock input frequencies. Updated block diagram Updated part number Updated package diagram *E 2011-03-24 Updated Slave FIFO protocol and added ZLP signaling protocol Changed GPIFII asynchronous tDO parameter Changed Async Slave FIFO tOE parameter Changed Async Slave FIFO tRDO parameter Added tCOE parameter to GPIFII Sync mode timing parameters Renamed GPIFII Sync mode tDO to tCO and tDO_ss0 to tCO_ss0 Modified description of GPIFII Sync tCO (previously tDO) parameter Changed tAH(address hold time) parameter in Async Slave FIFO modes to be with respect to rising edge of SLWR#/SLRD# instead of falling edge. Correspondingly, changed the tAH number. Removed 24 bit data bus support for GPIFII. *F 2011-04-07 Minor ECN - Release to web. No content changes. *G 2011-04-20 Minor updates in Features. *H 2011-04-06 Updated GPIFII Synchronous Timing diagram. Added SPI Boot option. Corrected values of R_USB2 and R_USB3. Corrected TCK and TRST# pull-up/pull-down configuration. Minor updates to block diagrams. Corrected Synchronous Slave FIFO tDH parameter. *I 2011-07-07 Minor ECN - Correct ECN number in revision *F. No content changes. *J 2011-12-06 Changed datasheet status from Preliminary to Final. Changed tWRPE parameter to 2 ns Updated tRR and tRPW for crystal input Added clarification regarding IOZ and IIX Updated Sync SLave FIFO Read timing diagram Updated SPI timing diagram Removed tGRANULARITY parameter Updated I2S Timing diagram and tTd parameter Updated 121-ball BGA package diagram. Added clarification regarding VCC in DC Specifications table In Power Modes description, stated that VIO1 cannot be turned off at any time if the GPIFII is used in the application Updated Absolute Maximum Ratings Added requirement for by-pass capacitor on U3RXVDDQ and U3TXVDDQ Updated tPEI parameter in Async Slave FIFO timing table Updated Sync Slave FIFO write and read timing diagrams Updated I2C interface tVD:ACK parameter for 1MHz operation Clarified that CTL[15] is not usable as a GPIO *K 2012-02-24 Corrected typo in the block diagram. *D Datasheet 76 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Revision history Document revision Date Description of changes *L 2012-08-16 Changed part number to CYUSB301X. Added 256 KB range for embedded SRAM. Updated Functional Overview, Other Interfaces, and Clocking sections. Added Pin List for CYUSB3011 and CYUSB3013 parts. Updated Ordering information: Updated part numbers. *M 2012-12-20 Updated 121-ball BGA package diagram to current revision. 2013-05-31 Included Commercial Temperature Range related information in all instances across the document. Included 131-ball WLCSP Package related information in all instances across the document. Updated Pin description: Updated Table 7. Updated Package diagram: Added 131-ball WLCSP Package Diagram. Updated Ordering information: Updated part numbers. *O 2014-05-02 Updated Package diagram: spec 001-62221 – Changed revision from *B to *C. Updated to new template. Completing Sunset Review. *P 2014-08-14 Added CYUSB201x MPNs, ball map, and pin list to the datasheet. *N Datasheet 77 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Revision history Document revision *Q *R Datasheet Date Description of changes 2015-02-24 Updated Features: Updated description. Updated Logic block diagram. Updated Functional description: Added “For a complete list of related documentation, click here.” at the end. Added More information. Updated Functional overview: Updated Application examples: Updated Figure 1. Updated Figure 2. Updated USB interface: Updated description. Removed Figure “USB Interface Signals”. Updated Reset: Updated Hard reset: Updated description. Updated Pin configurations: Updated Figure 6. Updated Pin description: Updated Table 7: Updated entire table. Modified CVDDQ power domain description. Removed Table “CYUSB3011 and CYUSB3013 Pin List (GPIF II with 16-bit Data Bus Width)”. Removed Table “CYUSB2014 Pin List (GPIF II with 32-bit Data Bus Width)”. Updated DC specifications: Added ISS parameter and its details. Updated Slave FIFO interface: Updated Synchronous Slave FIFO Read sequence description: Updated Figure 11. Updated Synchronous Slave FIFO Write sequence description: Updated Figure 12. Updated Table 15. Updated AC timing parameters: Added Host Processor Interface (P-Port) timing. Updated Acronyms. Added Errata. Replaced West Bridge Benicia with FX3. 2015-03-27 Updated Slave FIFO interface: Updated Synchronous Slave FIFO Read sequence description: Updated Figure 11. Updated Synchronous Slave FIFO Write sequence description: Updated Figure 12. Updated Table 15: Updated minimum value of tSSD parameter. Added tACCD, tFAD parameters and their details. 78 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Revision history Document revision Date Description of changes 2016-04-07 Updated Electrical specifications: Updated DC specifications: Updated Table 8 (Removed ISS parameter and its corresponding details). Updated Errata: Updated Errata summary: Updated description. Added item “Bus collision is seen when the I2C block is used as a master in the I2C Multi-master configuration.” and its corresponding details in the table. *T 2016-06-29 Updated AC timing parameters: Updated GPIF II timing: Updated Table 13: Changed maximum value of tCO parameter from 8 ns to 7 ns. Updated Slave FIFO interface: Updated Synchronous Slave FIFO Write sequence description: Updated Table 15: Changed maximum value of tCO parameter from 8 ns to 7 ns. Updated to new template. *U 2017-04-20 Updated Cypress Logo and Copyright. 2018-02-19 Removed 131-ball WLCSP Package related information in all instances across the document. Updated Package diagram: spec 001-54471 – Changed revision from *E to *F. Updated to new template. *S *V Datasheet 79 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Revision history Document revision *W *X Datasheet Date Description of changes 2018-09-25 Updated Features: Updated description. Updated More information: Updated description. Updated Functional overview: Updated description. Updated USB interface: Removed “EZ-Dtect”. Updated JTAG interface: Updated description. Updated Other interfaces: Updated I2S interface: Updated description. Updated Boot options: Updated description. Updated Power: Updated description. Updated Table 6. Updated Pin configurations: Updated Figure 6. Updated Figure 7. Updated Pin description: Updated Table 7. Updated Electrical specifications: Updated DC specifications: Updated Table 8. Added Table 9. Added Thermal characteristics. Updated AC timing parameters: Added GPIF II lines AC characteristics at 100 MHz. Added GPIF II PCLK jitter characteristics. Updated Errata: Updated description. Updated Errata summary: Updated description. Updated details in “Silicon Revision” column for all items in the table. Added items “Low Power U1 Fast-Exit Issue with USB3.0 host controller.”, “USB data corruption when operating on hosts with poor link quality.”, “Device treats Rx Detect sequence from the USB 3.0 host as a valid U1 exit LFPS burst.”, “I2C Data Valid (tVD:DAT) specification violation at 400 kHz with a 40/60 duty cycle.” and their corresponding details in the table. 2018-12-17 Updated Pin description: Updated Table 7. Updated Errata: Updated Errata summary: Updated description. Added item “FX3 Device does not respond correctly to Port Capability Request from Host after multiple power cycles.” and its corresponding details in the table. 80 001-52136 Rev. *Z 2022-09-29 EZ-USB FX3 SuperSpeed USB Controller Revision history Document revision *Y *Z Datasheet Date Description of changes 2022-08-11 Updated Document Title to read as “CYUSB301X, CYUSB201X, EZ-USB FX3 SuperSpeed USB Controller”. Added a note on Errata in page 2. Updated More information: Updated description. Added hyperlink in required places. Updated Functional overview: Updated Application examples: Updated Figure 1. Updated Figure 2. Updated USB interface: Updated description. Updated Boot options: Updated description. Updated Errata: Updated Errata summary: Updated details in “[Part Number]” column for Errata items 7, 8, 9, and 11. Migrated to Infineon template. 2022-09-29 Updated Features: Updated description. Updated More information: Updated description. Updated hyperlinks. Updated Functional overview: Updated description. Updated USB interface: Updated description. Updated Boot options: Updated description. Updated Table 2. Updated Electrical specifications: Updated Absolute maximum ratings: Updated details corresponding to “Latch-up current”. Updated Pin description: Updated Table 7. 81 001-52136 Rev. *Z 2022-09-29 Please read the Important Notice and Warnings at the end of this document Trademarks All referenced product or service names and trademarks are the property of their respective owners. Edition 2022-09-29 Published by Infineon Technologies AG 81726 Munich, Germany © 2022 Infineon Technologies AG. All Rights Reserved. Do you have a question about this document? Go to www.infineon.com/support Document reference 001-52136 Rev. *Z IMPORTANT NOTICE The information given in this document shall in no For further information on the product, technology, event be regarded as a guarantee of conditions or delivery terms and conditions and prices please contact your nearest Infineon Technologies office characteristics (“Beschaffenheitsgarantie”). (www.infineon.com). With respect to any examples, hints or any typical values stated herein and/or any information WARNINGS regarding the application of the product, Infineon Due to technical requirements products may contain Technologies hereby disclaims any and all dangerous substances. For information on the types warranties and liabilities of any kind, including in question please contact your nearest Infineon without limitation warranties of non-infringement of Technologies office. intellectual property rights of any third party. In addition, any information given in this document is subject to customer’s compliance with its obligations stated in this document and any applicable legal requirements, norms and standards concerning customer’s products and any use of the product of Infineon Technologies in customer’s applications. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer’s technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies’ products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury.
CYUSB3011-BZXC 价格&库存

很抱歉,暂时无法提供与“CYUSB3011-BZXC”相匹配的价格&库存,您可以联系我们找货

免费人工找货