MB9AF114LAQN-G-AVE2

Please note that Cypress is an Infineon Technologies Company. The document following this cover page is marked as “Cypress” document as this is the company that originally developed the product. Please note that Infineon will continue to offer the product to new and existing customers as part of the Infineon product portfolio. Continuity of document content The fact that Infineon offers the following product as part of the Infineon product portfolio does not lead to any changes to this document. Future revisions will occur when appropriate, and any changes will be set out on the document history page. Continuity of ordering part numbers Infineon continues to support existing part numbers. Please continue to use the ordering part numbers listed in the datasheet for ordering. www.infineon.com CY9A110A/CY9A110 Series 32-bit Arm® Cortex®-M3 FM3 Microcontroller The CY9A110A/CY9A110 Series are highly integrated 32-bit microcontrollers that target for high-performance and cost-sensitive embedded control applications. The CY9A110A Series are based on the Arm® Cortex®-M3 Processor and on-chip Flash memory and SRAM, and peripheral functions, including Motor Control Timers, ADCs, Communication Interfaces (UART, CSIO, I2C, LIN). The products which are described in this datasheet are placed into TYPE1 product categories in “FM3 Family Peripheral Manual”. Features 32-bit Arm Cortex-M3 Core [UART]  Processor version: r2p1  Full duplex double buffer  Up to 40 MHz Frequency Operation  Selection with or without parity supported  Integrated Nested Vectored Interrupt Controller (NVIC): 1  Built-in dedicated baud rate generator NMI (non-maskable interrupt) and 48 peripheral interrupts and 16 priority levels  24-bit System timer (Sys Tick): System timer for OS task management  External clock available as a serial clock  Hardware Flow control: Automatically control the transmission by CTS/RTS (only ch.4)*  Various error detection functions available (parity errors, On-chip Memories framing errors, and overrun errors) *: CY9AF111LA, F112LA, F114LA, F112L and F114L do not support Hardware Flow control [Flash memory]  Up to 512 Kbyte [CSIO]  Read cycle: 0 wait-cycle  Full duplex double buffer  Security function for code protection  Built-in dedicated baud rate generator [SRAM]  Overrun error detection function available This Series contain a total of up to 32 Kbyte on-chip SRAM. On-chip SRAM is composed of two independent SRAM (SRAM0, SRAM1). SRAM0 is connected to I-code bus and Dcode bus of Cortex-M3 core. SRAM1 is connected to System bus. [LIN]  LIN protocol Rev.2.1 supported  Full duplex double buffer  SRAM0: Up to 16 Kbytes  Master/Slave mode supported  SRAM1: Up to 16 Kbytes  LIN break field generation (can be changed 13- 16bit length) Multi-function Serial Interface (Max 8 channels)  4 channels with 16 steps×9bit FIFO (ch.4-ch.7), 4 channels without FIFO (ch.0-ch3) channel.  UART  CSIO  LIN  I2 C Document Number: 002-04672 Rev. *F length)  Various error detection functions available (parity errors, framing errors, and overrun errors)  Operation mode is selectable from the followings for each Cypress Semiconductor Corporation An Infineon Technologies Company  LIN break delimiter generation (can be changed 1 - 4bit [I2C] Standard-mode (Max 100 kbps) / Fast-mode (Max 400 kbps) supported • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised April 29, 2020 CY9A110A/CY9A110 Series External Bus Interface*  Supports SRAM, NOR Flash device  Up to 8 chip selects  8-/16-bit Data width  Up to 25-bit Address bit  Maximum area size: Up to 256 Mbytes  Supports Address/Data multiplex  Supports external RDY function *: CY9AF111LA, F112LA and F114LA do not support External Bus Interface DMA Controller (8 channels) The DMA Controller has an independent bus from the CPU, so CPU and DMA Controller can process simultaneously. Multi-function Timer (Max 2 units) The Multi-function timer is composed of the following blocks.  16-bit free-run timer × 3 ch/unit  Input capture × 4 ch/unit  Output compare × 6 ch/unit  A/D activation compare × 3 ch/unit  Waveform generator × 3 ch/unit  16-bit PPG timer × 3 ch/unit The following function can be used to achieve the motor control.  PWM signal output function  DC chopper waveform output function  8 independently configured and operated channels  Dead timer function  Transfer can be started by software or request from the built-  Input capture function in peripherals  Transfer address area: 32bit (4 Gbytes)  Transfer mode: Block transfer/Burst transfer/Demand transfer  Transfer data type: byte/half-word/word  Transfer block count: 1 to 16  Number of transfers: 1 to 65536 A/D Converter (Max 16 channels)  A/D converter activate function  DTIF (Motor emergency stop) interrupt function Quadrature Position/Revolution Counter (QPRC) (Max 2 units) The Quadrature Position/Revolution Counter (QPRC) is used to measure the position of the position encoder. Moreover, it is possible to use up/down counter.  The detection edge of the three external event input pins AIN, BIN and ZIN is configurable. [12-bit A/D Converter]  16-bit position counter  Successive Approximation type  16-bit revolution counter  Built-in 3units*  Two 16-bit compare registers  Conversion time: 1.0 μs@5 V Dual Timer (32-/16-bit Down Counter)  Priority conversion available (priority at 2levels) The Dual Timer consists of two programmable 32-/16-bit down counters. Operation mode is selectable from the followings for each timer channel.  Scanning conversion mode  Built-in FIFO for conversion data storage (for SCAN conversion: 16 steps, for Priority conversion: 4steps) *: CY9AF111LA, F112LA, F114LA built-in 2units Base Timer (Max 8 channels) Operation mode is selectable from the followings for each channel.  16-bit PWM timer  16-bit PPG timer  16-/32-bit reload timer  Free-running  Periodic (=Reload)  One-shot Watch Counter The Watch counter is used for wake up from Low-Power Consumption mode.  Interval timer: up to 64 s(Max)@ Sub Clock: 32.768 kHz  16-/32-bit PWC timer Document Number: 002-04672 Rev. *F Page 2 of 110 CY9A110A/CY9A110 Series Watch dog Timer (2 channels) [Resets] A watchdog timer can generate interrupts or a reset when a time-out value is reached.  Reset requests from INITX pin This series consists of two different watchdogs, a "Hardware" watchdog and a "Software" watchdog.  Power-on reset The "Hardware" watchdog timer is clocked by the built-in lowspeed CR oscillator. Therefore, the "Hardware" watchdog is active in any low-power consumption modes except STOP modes.  Watchdog timers reset External Interrupt Controller Unit  Up to 16 external interrupt input pins  Include one non-maskable interrupt (NMI) input pin  Software reset  Low-voltage detector reset  Clock Supervisor reset Clock Super Visor (CSV) Clocks generated by built-in CR oscillators are used to supervise abnormality of the external clocks.  External clock failure (clock stop) is detected, reset is asserted. General-Purpose I/O Port This series can use its pins as general-purpose I/O ports when they are not used for external bus or peripherals. Moreover, the port relocate function is built in. It can set which I/O port the peripheral function can be allocated to.  External frequency anomaly is detected, interrupt or reset is  Capable of pull-up control per pin  Capable of reading pin level directly This Series includes 2-stage monitoring of voltage on the VCC. When the voltage falls below the voltage that has been set, Low-Voltage Detector generates an interrupt or reset.  Built-in the port relocate function  LVD1: error reporting via interrupt  Up to 83 fast General Purpose I/O Ports@ 100 pin Package  LVD2: auto-reset operation  Some ports are 5V tolerant I/O (CY9AF115MA/NA, CY9AF116MA/NA only) Please see "Pin Description" to confirm the corresponding pins. CRC (Cyclic Redundancy Check) Accelerator The CRC accelerator calculates the CRC which has a heavy software processing load, and achieves a reduction of the integrity check processing load for reception data and storage. CCITT CRC16 and IEEE-802.3 CRC32 are supported.  CCITT CRC16 Generator Polynomial: 0x1021  IEEE-802.3 CRC32 Generator Polynomial: 0x04C11DB7 Clock and Reset asserted. Low-Voltage Detector (LVD) Low-Power Consumption Mode Three Low-Power Consumption modes supported.  SLEEP  TIMER  STOP Debug  Serial Wire JTAG Debug Port (SWJ-DP)  Embedded Trace Macrocells (ETM)* *: CY9AF111LA/MA, F112LA/MA, F114LA/MA, F115MA and F116MA support only SWJ-DP. [Clocks] Power Supply Selectable from five clock sources (2 external oscillators, 2 built-in CR oscillators, and Main PLL).  VCC = 2.7 V to 5.5 V: Correspond to the wide range voltage.  Main Clock: 4 MHz to 48 MHz  Sub Clock: 32.768 kHz  Built-in High-speed CR Clock: 4 MHz  Built-in Low-speed CR Clock: 100 kHz  Main PLL Clock Document Number: 002-04672 Rev. *F Page 3 of 110 CY9A110A/CY9A110 Series Contents 1. Product Lineup ................................................................ 5 2. Packages ......................................................................... 6 3. Pin Assignment ............................................................... 7 4. List of Pin Functions..................................................... 13 5. I/O Circuit Type.............................................................. 38 6. Handling Precautions ................................................... 43 6.1 Precautions for Product Design ................................. 43 6.2 Precautions for Package Mounting ............................ 44 6.3 Precautions for Use Environment .............................. 45 7. Handling Devices .......................................................... 46 8. Block Diagram ............................................................... 48 9. Memory Size .................................................................. 49 10. Memory Map .................................................................. 49 11. Pin Status in Each CPU State ...................................... 53 12. Electrical Characteristics ............................................. 57 12.1 Absolute Maximum Ratings ....................................... 57 12.2 Recommended Operating Conditions........................ 59 Document Number: 002-04672 Rev. *F 12.3 DC Characteristics ..................................................... 60 12.4 AC Characteristics ..................................................... 63 12.5 12-bit A/D Converter .................................................. 89 12.6 Low-voltage detection characteristics ........................ 92 12.7 Flash Memory Write/Erase Characteristics ................ 93 12.8 Return Time from Low-Power Consumption Mode .... 94 13. Ordering Information..................................................... 98 14. Package Dimensions..................................................... 99 15. Errata ............................................................................ 106 15.1 Part Numbers Affected ............................................ 106 15.2 Qualification Status .................................................. 106 15.3 Errata Summary....................................................... 106 16. Major Changes............................................................. 107 Document History ............................................................. 109 Sales, Solutions, and Legal Information ......................... 110 Page 4 of 110 CY9A110A/CY9A110 Series 1. Product Lineup Memory Size Product name CY9AF112LA/MA/NA CY9AF112L CY9AF111LA/MA/NA CY9AF114LA/MA/NA CY9AF114L On-chip Flash memory 64 Kbytes 128 Kbytes 256 Kbytes On-chip SRAM 16 Kbytes 16 Kbytes 32 Kbytes Product name CY9AF115MA/NA CY9AF116MA/NA On-chip Flash memory 384 Kbytes 512 Kbytes On-chip SRAM 32 Kbytes 32 Kbytes Function CY9AF111LA CY9AF112LA CY9AF114LA CY9AF112L CY9AF114L Product name Pin count 64 Cortex-M3 40 MHz 2.7 V to 5.5 V 8 ch. CPU Freq. Power supply voltage range DMAC CY9AF111MA CY9AF112MA CY9AF114MA CY9AF115MA CY9AF116MA 80 100 Addr:21-bit (Max) Data:8-bit CS:4 (Max) Support: SRAM, NOR Flash Addr:25-bit (Max) Data:8-/16-bit CS:8 (Max) Support: SRAM, NOR Flash External Bus Interface - Multi-function Serial Interface (UART/CSIO/LIN/I2C) 8 ch. (Max) ch.4 to ch.7: FIFO (16 steps x 9-bit) ch.0 to ch.3: No FIFO MF-Timer Base Timer (PWC/Reload timer/PWM/PPG) A/D activation compare Input capture Free-run timer Output compare Waveform generator PPG QPRC CY9AF111NA CY9AF112NA CY9AF114NA CY9AF115NA CY9AF116NA 8 ch. (Max) 3 ch. 4 ch. 3 ch. 6 ch. 3 ch. 3 ch. 1 unit 2 units (Max) 2 ch. (Max) Dual Timer 1 unit Watch Counter CRC Accelerator Watchdog timer External Interrupts I/O ports 12-bit A/D converter CSV (Clock Super Visor) LVD (Low-Voltage Detector) High-speed Built-in CR Low-speed Debug Function 1 unit Yes 1 ch. (SW) + 1 ch. (HW) 8 pins (Max) + NMI × 1 51 pins (Max) 9 ch. (2 units) Yes 2 ch. 4 MHz 100 kHz SWJ-DP 11 pins (Max) + NMI × 1 66 pins (Max) 12 ch. (3 units) 16 pins (Max) + NMI × 1 83 pins (Max) 16 ch. (3 units) SWJ-DP/ETM Note: − All signals of the peripheral function in each product cannot be allocated by limiting the pins of package. It is necessary to use the port relocate function of the I/O port according to your function use. See “12. Electrical Characteristics 12.4. AC Characteristics 12.4.3. Built-in CR Oscillation Characteristics” for accuracy of built-in CR. Document Number: 002-04672 Rev. *F Page 5 of 110 CY9A110A/CY9A110 Series 2. Packages Package Product name CY9AF111LA CY9AF112LA CY9AF114LA CY9AF112L CY9AF114L CY9AF111MA CY9AF112MA CY9AF114MA CY9AF115MA CY9AF116MA CY9AF111NA CY9AF112NA CY9AF114NA CY9AF115NA CY9AF116NA LQFP:LQD064 (0.5 mm pitch)  - - - LQFP:LQG064 (0.65 mm pitch)   - - QFN :VNC064 (0.5 mm pitch)  - - - LQFP:LQH080 (0.5 mm pitch) - -  - LQFP:LQI100 (0.65 mm pitch) - - -  QFP :PQH100 (0.65 mm pitch) - - -  BGA :LBC112 (0.8 mm pitch) - - - * : Supported *: CY9AF115NA, CY9AF116NA are planning Note: − Refer to “14. Package Dimensions” for detailed information on each package. Document Number: 002-04672 Rev. *F Page 6 of 110 CY9A110A/CY9A110 Series 3. Pin Assignment LQI100 VSS P81 P80 VCC P60/SIN5_0/TIOA2_2/INT15_1/MRDY_1 P61/SOT5_0/TIOB2_2 P62/SCK5_0/ADTG_3/MOEX_1 P63/INT03_0/MWEX_1 P0F/NMIX/CROUT_1 P0E/CTS4_0/TIOB3_2/IC13_0/MDQM1_1 P0D/RTS4_0/TIOA3_2/IC12_0/MDQM0_1 P0C/SCK4_0/TIOA6_1/IC11_0/MALE_1 P0B/SOT4_0/TIOB6_1/IC10_0/MCSX0_1 P0A/SIN4_0/INT00_2/FRCK1_0/MCSX1_1 P09/TRACECLK/TIOB0_2/RTS4_2/MCSX2_1 P08/TRACED3/TIOA0_2/CTS4_2/MCSX3_1 P07/TRACED2/ADTG_0/SCK4_2/MCLKOUT_1 P06/TRACED1/TIOB5_2/SOT4_2/INT01_1/MCSX4_1 P05/TRACED0/TIOA5_2/SIN4_2/INT00_1/MCSX5_1 P04/TDO/SWO P03/TMS/SWDIO P02/TDI/MCSX6_1 P01/TCK/SWCLK P00/TRSTX/MCSX7_1 VCC 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 (TOP VIEW) VCC 1 75 VSS P50/INT00_0/AIN0_2/SIN3_1/RTO10_0/MADATA00_1 2 74 P20/INT05_0/CROUT_0/AIN1_1/MAD24_1 P51/INT01_0/BIN0_2/SOT3_1/RTO11_0/MADATA01_1 3 73 P21/SIN0_0/INT06_1/BIN1_1 P52/INT02_0/ZIN0_2/SCK3_1/RTO12_0/MADATA02_1 4 72 P22/SOT0_0/TIOB7_1/ZIN1_1 P53/SIN6_0/TIOA1_2/INT07_2/RTO13_0/MADATA03_1 5 71 P23/SCK0_0/TIOA7_1/RTO00_1 P54/SOT6_0/TIOB1_2/RTO14_0/MADATA04_1 6 70 P1F/AN15/ADTG_5/FRCK0_1/MAD23_1 P55/SCK6_0/ADTG_1/RTO15_0/MADATA05_1 7 69 P1E/AN14/RTS4_1/DTTI0X_1/MAD22_1 P56/INT08_2/DTTI1X_0/MADATA06_1 8 68 P1D/AN13/CTS4_1/IC03_1/MAD21_1 P30/AIN0_0/TIOB0_1/INT03_2/MADATA07_1 9 67 P1C/AN12/SCK4_1/IC02_1/MAD20_1 P31/BIN0_0/TIOB1_1/SCK6_1/INT04_2/MADATA08_1 10 66 P1B/AN11/SOT4_1/IC01_1/MAD19_1 P32/ZIN0_0/TIOB2_1/SOT6_1/INT05_2/MADATA09_1 11 65 P1A/AN10/SIN4_1/INT05_1/IC00_1/MAD18_1 P33/INT04_0/TIOB3_1/SIN6_1/ADTG_6/MADATA10_1 12 64 P19/AN09/SCK2_2/MAD17_1 LQFP - 100 47 48 49 50 PE3/X1 VSS 46 PE0/MD1 MD0 45 P4E/TIOB5_0/INT06_2/SIN7_1/ZIN1_2/MAD08_1 PE2/X0 44 VCC P4D/TIOB4_0/FRCK1_1/SOT7_1/BIN1_2/MAD07_1 51 43 25 P4C/TIOB3_0/IC13_1/SCK7_1/AIN1_2/MAD06_1 P10/AN00 VSS 42 52 P4B/TIOB2_0/IC12_1/ZIN0_1/MAD05_1 24 41 P11/AN01/SIN1_1/INT02_1/FRCK0_2/MAD09_1 P3F/RTO05_0/TIOA5_1 P4A/TIOB1_0/IC11_1/BIN0_1/SCK3_2/MAD04_1 53 40 23 P49/TIOB0_0/IC10_1/AIN0_1/SOT3_2/MAD03_1 P12/AN02/SOT1_1/IC00_2/MAD10_1 P3E/RTO04_0/TIOA4_1 39 54 P48/DTTI1X_1/INT14_1/SIN3_2/MAD02_1 22 38 P13/AN03/SCK1_1/IC01_2/MAD11_1 P3D/RTO03_0/TIOA3_1 INITX 55 37 21 36 P14/AN04/SIN0_1/INT03_1/IC02_2/MAD12_1 P3C/RTO02_0/TIOA2_1 P47/X1A 56 35 20 VCC P15/AN05/SOT0_1/IC03_2/MAD13_1 P3B/RTO01_0/TIOA1_1 P46/X0A 57 34 19 VSS P16/AN06/SCK0_1/MAD14_1 P3A/RTO00_0/TIOA0_1 33 58 C 18 32 P17/AN07/SIN2_2/INT04_1/MAD15_1 P39/DTTI0X_0/ADTG_2 P45/TIOA5_0/RTO15_1/MAD01_1 59 31 17 P44/TIOA4_0/RTO14_1/MAD00_1 AVCC P38/IC00_0/SCK5_2/INT11_1/MADATA15_1 30 60 P43/TIOA3_0/RTO13_1/ADTG_7 16 29 AVRH P37/IC01_0/SOT5_2/INT10_1/MADATA14_1 P42/TIOA2_0/RTO12_1 61 28 15 P41/TIOA1_0/RTO11_1/INT13_1 AVSS P36/IC02_0/SIN5_2/INT09_1/MADATA13_1 27 P18/AN08/SOT2_2/MAD16_1 62 26 63 14 VCC 13 P40/TIOA0_0/RTO10_1/INT12_1 P34/FRCK0_0/TIOB4_1/MADATA11_1 P35/IC03_0/TIOB5_1/INT08_1/MADATA12_1 Note: − The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR) to select the pin. Document Number: 002-04672 Rev. *F Page 7 of 110 CY9A110A/CY9A110 Series PQH100 P50/INT00_0/AIN0_2/SIN3_1/RTO10_0/MADATA00_1 VCC VSS P81 P80 VCC P60/SIN5_0/TIOA2_2/INT15_1/MRDY_1 P61/SOT5_0/TIOB2_2 P62/SCK5_0/ADTG_3/MOEX_1 P63/INT03_0/MWEX_1 P0F/NMIX/CROUT_1 P0E/CTS4_0/TIOB3_2/IC13_0/MDQM1_1 P0D/RTS4_0/TIOA3_2/IC12_0/MDQM0_1 P0C/SCK4_0/TIOA6_1/IC11_0/MALE_1 P0B/SOT4_0/TIOB6_1/IC10_0/MCSX0_1 P0A/SIN4_0/INT00_2/FRCK1_0/MCSX1_1 P09/TRACECLK/TIOB0_2/RTS4_2/MCSX2_1 P08/TRACED3/TIOA0_2/CTS4_2/MCSX3_1 P07/TRACED2/ADTG_0/SCK4_2/MCLKOUT_1 P06/TRACED1/TIOB5_2/SOT4_2/INT01_1/MCSX4_1 P05/TRACED0/TIOA5_2/SIN4_2/INT00_1/MCSX5_1 P04/TDO/SWO P03/TMS/SWDIO P02/TDI/MCSX6_1 P01/TCK/SWCLK P00/TRSTX/MCSX7_1 VCC VSS P20/INT05_0/CROUT_0/AIN1_1/MAD24_1 P21/SIN0_0/INT06_1/BIN1_1 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 (TOP VIEW) P51/INT01_0/BIN0_2/SOT3_1/RTO11_0/MADATA01_1 81 50 P22/SOT0_0/TIOB7_1/ZIN1_1 P52/INT02_0/ZIN0_2/SCK3_1/RTO12_0/MADATA02_1 82 49 P23/SCK0_0/TIOA7_1/RTO00_1 P53/SIN6_0/TIOA1_2/INT07_2/RTO13_0/MADATA03_1 83 48 P1F/AN15/ADTG_5/FRCK0_1/MAD23_1 P54/SOT6_0/TIOB1_2/RTO14_0/MADATA04_1 84 47 P1E/AN14/RTS4_1/DTTI0X_1/MAD22_1 P55/SCK6_0/ADTG_1/RTO15_0/MADATA05_1 85 46 P1D/AN13/CTS4_1/IC03_1/MAD21_1 P56/INT08_2/DTTI1X_0/MADATA06_1 86 45 P1C/AN12/SCK4_1/IC02_1/MAD20_1 P30/AIN0_0/TIOB0_1/INT03_2/MADATA07_1 87 44 P1B/AN11/SOT4_1/IC01_1/MAD19_1 P31/BIN0_0/TIOB1_1/SCK6_1/INT04_2/MADATA08_1 88 43 P1A/AN10/SIN4_1/INT05_1/IC00_1/MAD18_1 P32/ZIN0_0/TIOB2_1/SOT6_1/INT05_2/MADATA09_1 89 42 P19/AN09/SCK2_2/MAD17_1 P33/INT04_0/TIOB3_1/SIN6_1/ADTG_6/MADATA10_1 90 41 P18/AN08/SOT2_2/MAD16_1 P34/FRCK0_0/TIOB4_1/MADATA11_1 91 40 AVSS P35/IC03_0/TIOB5_1/INT08_1/MADATA12_1 92 39 AVRH P36/IC02_0/SIN5_2/INT09_1/MADATA13_1 93 38 AVCC P37/IC01_0/SOT5_2/INT10_1/MADATA14_1 94 37 P17/AN07/SIN2_2/INT04_1/MAD15_1 P38/IC00_0/SCK5_2/INT11_1/MADATA15_1 95 36 P16/AN06/SCK0_1/MAD14_1 P39/DTTI0X_0/ADTG_2 96 35 P15/AN05/SOT0_1/IC03_2/MAD13_1 P3A/RTO00_0/TIOA0_1 97 34 P14/AN04/SIN0_1/INT03_1/IC02_2/MAD12_1 P3B/RTO01_0/TIOA1_1 98 33 P13/AN03/SCK1_1/IC01_2/MAD11_1 P3C/RTO02_0/TIOA2_1 99 32 P12/AN02/SOT1_1/IC00_2/MAD10_1 P3D/RTO03_0/TIOA3_1 100 31 P11/AN01/SIN1_1/INT02_1/FRCK0_2/MAD09_1 18 19 20 21 22 23 24 25 26 27 28 29 30 P4A/TIOB1_0/IC11_1/BIN0_1/SCK3_2/MAD04_1 P4B/TIOB2_0/IC12_1/ZIN0_1/MAD05_1 P4C/TIOB3_0/IC13_1/SCK7_1/AIN1_2/MAD06_1 P4D/TIOB4_0/FRCK1_1/SOT7_1/BIN1_2/MAD07_1 P4E/TIOB5_0/INT06_2/SIN7_1/ZIN1_2/MAD08_1 PE0/MD1 MD0 PE2/X0 PE3/X1 VSS VCC P10/AN00 12 VSS 17 11 C P48/DTTI1X_1/INT14_1/SIN3_2/MAD02_1 10 P45/TIOA5_0/RTO15_1/MAD01_1 P49/TIOB0_0/IC10_1/AIN0_1/SOT3_2/MAD03_1 9 P44/TIOA4_0/RTO14_1/MAD00_1 16 8 P43/TIOA3_0/RTO13_1/ADTG_7 INITX 7 P42/TIOA2_0/RTO12_1 15 6 P41/TIOA1_0/RTO11_1/INT13_1 14 5 P40/TIOA0_0/RTO10_1/INT12_1 P47/X1A 4 VCC 13 3 VSS VCC 2 P3F/RTO05_0/TIOA5_1 P46/X0A 1 P3E/RTO04_0/TIOA4_1 QFP - 100 Note: − The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR) to select the pin. Document Number: 002-04672 Rev. *F Page 8 of 110 CY9A110A/CY9A110 Series LQH080 VSS P81 P80 VCC P60/SIN5_0/TIOA2_2/INT15_1/MRDY_1 P61/SOT5_0/TIOB2_2 P62/SCK5_0/ADTG_3/MOEX_1 P63/INT03_0/MWEX_1 P0F/NMIX/CROUT_1 P0E/CTS4_0/TIOB3_2/IC13_0/MDQM1_1 P0D/RTS4_0/TIOA3_2/IC12_0/MDQM0_1 P0C/SCK4_0/TIOA6_1/IC11_0/MALE_1 P0B/SOT4_0/TIOB6_1/IC10_0/MCSX0_1 P0A/SIN4_0/INT00_2/FRCK1_0/MCSX1_1 P07/ADTG_0/MCLKOUT_1 P04/TDO/SWO P03/TMS/SWDIO P02/TDI/MCSX6_1 P01/TCK/SWCLK P00/TRSTX/MCSX7_1 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 (TOP VIEW) VCC 1 60 P20/INT05_0/CROUT_0/AIN1_1/MAD24_1 P50/INT00_0/AIN0_2/SIN3_1/RTO10_0/MADATA00_1 2 59 P21/SIN0_0/INT06_1/BIN1_1 P51/INT01_0/BIN0_2/SOT3_1/RTO11_0/MADATA01_1 3 58 P22/SOT0_0/TIOB7_1/ZIN1_1 P52/INT02_0/ZIN0_2/SCK3_1/RTO12_0/MADATA02_1 4 57 P23/SCK0_0/TIOA7_1 P53/SIN6_0/TIOA1_2/INT07_2/RTO13_0/MADATA03_1 5 56 P1B/AN11/SOT4_1/IC01_1/MAD19_1 P54/SOT6_0/TIOB1_2/RTO14_0/MADATA04_1 6 55 P1A/AN10/SIN4_1/INT05_1/IC00_1/MAD18_1 P55/SCK6_0/ADTG_1/RTO15_0/MADATA05_1 7 54 P19/AN09/SCK2_2/MAD17_1 P56/INT08_2/DTTI1X_0/MADATA06_1 8 53 P18/AN08/SOT2_2/MAD16_1 P30/AIN0_0/TIOB0_1/INT03_2/MADATA07_1 9 52 AVSS P31/BIN0_0/TIOB1_1/SCK6_1/INT04_2/MADATA08_1 10 51 AVRH P32/ZIN0_0/TIOB2_1/SOT6_1/INT05_2/MADATA09_1 11 50 AVCC P33/INT04_0/TIOB3_1/SIN6_1/ADTG_6/MADATA10_1 12 49 P17/AN07/SIN2_2/INT04_1/MAD15_1 P39/DTTI0X_0/ADTG_2 13 48 P16/AN06/SCK0_1/MAD14_1 P3A/RTO00_0/TIOA0_1 14 47 P15/AN05/SOT0_1/IC03_2/MAD13_1 P3B/RTO01_0/TIOA1_1 15 46 P14/AN04/SIN0_1/INT03_1/IC02_2/MAD12_1 P3C/RTO02_0/TIOA2_1 16 45 P13/AN03/SCK1_1/IC01_2/MAD11_1 P3D/RTO03_0/TIOA3_1 17 44 P12/AN02/SOT1_1/IC00_2/MAD10_1 P3E/RTO04_0/TIOA4_1 18 43 P11/AN01/SIN1_1/INT02_1/FRCK0_2/MAD09_1 P3F/RTO05_0/TIOA5_1 19 42 P10/AN00 VSS 20 41 VCC 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 P44/TIOA4_0/MAD00_1 P45/TIOA5_0/MAD01_1 C VSS VCC P46/X0A P47/X1A INITX P48/DTTI1X_1/INT14_1/SIN3_2/MAD02_1 P49/TIOB0_0/IC10_1/AIN0_1/SOT3_2/MAD03_1 P4A/TIOB1_0/IC11_1/BIN0_1/SCK3_2/MAD04_1 P4B/TIOB2_0/IC12_1/ZIN0_1/MAD05_1 P4C/TIOB3_0/IC13_1/SCK7_1/AIN1_2/MAD06_1 P4D/TIOB4_0/FRCK1_1/SOT7_1/BIN1_2/MAD07_1 P4E/TIOB5_0/INT06_2/SIN7_1/ZIN1_2/MAD08_1 PE0/MD1 MD0 PE2/X0 PE3/X1 VSS LQFP - 80 Note: − The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR) to select the pin. Document Number: 002-04672 Rev. *F Page 9 of 110 CY9A110A/CY9A110 Series LQD064/LQG064 VSS P81 P80 VCC P60/SIN5_0/TIOA2_2/INT15_1 P61/SOT5_0/TIOB2_2 P62/SCK5_0/ADTG_3 P0F/NMIX/CROUT_1 P0C/SCK4_0/TIOA6_1 P0B/SOT4_0/TIOB6_1 P0A/SIN4_0/INT00_2 P04/TDO/SWO P03/TMS/SWDIO P02/TDI P01/TCK/SWCLK P00/TRSTX 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 (TOP VIEW) VCC 1 48 P21/SIN0_0/INT06_1 P50/INT00_0/AIN0_2/SIN3_1 2 47 P22/SOT0_0/TIOB7_1 P51/INT01_0/BIN0_2/SOT3_1 3 46 P23/SCK0_0/TIOA7_1 P52/INT02_0/ZIN0_2/SCK3_1 4 45 P19/AN09/SCK2_2 P30/AIN0_0/TIOB0_1/INT03_2 5 44 P18/AN08/SOT2_2 P31/BIN0_0/TIOB1_1/SCK6_1/INT04_2 6 43 AVSS P32/ZIN0_0/TIOB2_1/SOT6_1/INT05_2 7 42 AVRH P33/INT04_0/TIOB3_1/SIN6_1/ADTG_6 8 41 AVCC P39/DTTI0X_0/ADTG_2 9 40 P17/AN07/SIN2_2/INT04_1 P3A/RTO00_0/TIOA0_1 10 39 P15/AN05/IC03_2 P3B/RTO01_0/TIOA1_1 11 38 P14/AN04/INT03_1/IC02_2 P3C/RTO02_0/TIOA2_1 12 37 P13/AN03/SCK1_1/IC01_2 P3D/RTO03_0/TIOA3_1 13 36 P12/AN02/SOT1_1/IC00_2 P3E/RTO04_0/TIOA4_1 14 35 P11/AN01/SIN1_1/INT02_1/FRCK0_2 P3F/RTO05_0/TIOA5_1 15 34 P10/AN00 VSS 16 33 VCC 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 C VCC P46/X0A P47/X1A INITX P49/TIOB0_0/AIN0_1 P4A/TIOB1_0/BIN0_1 P4B/TIOB2_0/ZIN0_1 P4C/TIOB3_0/SCK7_1/AIN1_2 P4D/TIOB4_0/SOT7_1/BIN1_2 P4E/TIOB5_0/INT06_2/SIN7_1/ZIN1_2 PE0/MD1 MD0 PE2/X0 PE3/X1 VSS LQFP - 64 Note: − The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR) to select the pin. Document Number: 002-04672 Rev. *F Page 10 of 110 CY9A110A/CY9A110 Series LBC112 1 2 3 4 5 6 7 8 9 10 11 A VSS P81 P80 VCC P0E P0B P07 TMS/ SWDIO TRSTX VCC VSS B VCC VSS P52 P61 P0F P0C P08 TDO/ SWO TCK/ SWCLK VSS TDI C P50 P51 VSS P60 P62 P0D P09 P05 VSS P20 P21 D P53 P54 P55 VSS P56 P63 P0A VSS P06 P23 AN15 E P30 P31 P32 P33 Index P22 AN14 AN12 AN11 F P34 P35 P36 P39 AN13 AN10 AN09 AVRH G P37 P38 P3A P3D AN08 AN07 AN06 AVSS H P3B P3C P3E VSS P44 P4C AN05 VSS AN04 AN03 AVCC J VCC P3F VSS P40 P43 P49 P4D AN02 VSS AN01 AN00 K VCC VSS X1A INITX P42 P48 P4B P4E MD1 VSS VCC L VSS C X0A VSS P41 P45 P4A MD0 X0 X1 VSS PFBGA - 112 Note: − The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR) to select the pin. Document Number: 002-04672 Rev. *F Page 11 of 110 CY9A110A/CY9A110 Series VNC064 VSS P81 P80 VCC P60/SIN5_0/TIOA2_2/INT15_1 P61/SOT5_0/TIOB2_2 P62/SCK5_0/ADTG_3 P0F/NMIX/CROUT_1 P0C/SCK4_0/TIOA6_1 P0B/SOT4_0/TIOB6_1 P0A/SIN4_0/INT00_2 P04/TDO/SWO P03/TMS/SWDIO P02/TDI P01/TCK/SWCLK P00/TRSTX 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 (TOP VIEW) VCC 1 48 P21/SIN0_0/INT06_1 P50/INT00_0/AIN0_2/SIN3_1 2 47 P22/SOT0_0/TIOB7_1 P51/INT01_0/BIN0_2/SOT3_1 3 46 P23/SCK0_0/TIOA7_1 P52/INT02_0/ZIN0_2/SCK3_1 4 45 P19/AN09/SCK2_2 P30/AIN0_0/TIOB0_1/INT03_2 5 44 P18/AN08/SOT2_2 P31/BIN0_0/TIOB1_1/SCK6_1/INT04_2 6 43 AVSS P32/ZIN0_0/TIOB2_1/SOT6_1/INT05_2 7 42 AVRH P33/INT04_0/TIOB3_1/SIN6_1/ADTG_6 8 41 AVCC P39/DTTI0X_0/ADTG_2 9 40 P17/AN07/SIN2_2/INT04_1 P3A/RTO00_0/TIOA0_1 10 39 P15/AN05/IC03_2 P3B/RTO01_0/TIOA1_1 11 38 P14/AN04/INT03_1/IC02_2 P3C/RTO02_0/TIOA2_1 12 37 P13/AN03/SCK1_1/IC01_2 P3D/RTO03_0/TIOA3_1 13 36 P12/AN02/SOT1_1/IC00_2 P3E/RTO04_0/TIOA4_1 14 35 P11/AN01/SIN1_1/INT02_1/FRCK0_2 P3F/RTO05_0/TIOA5_1 15 34 P10/AN00 VSS 16 33 VCC 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 C VCC P46/X0A P47/X1A INITX P49/TIOB0_0/AIN0_1 P4A/TIOB1_0/BIN0_1 P4B/TIOB2_0/ZIN0_1 P4C/TIOB3_0/SCK7_1/AIN1_2 P4D/TIOB4_0/SOT7_1/BIN1_2 P4E/TIOB5_0/INT06_2/SIN7_1/ZIN1_2 PE0/MD1 MD0 PE2/X0 PE3/X1 VSS QFN - 64 Note: − The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR) to select the pin. Document Number: 002-04672 Rev. *F Page 12 of 110 CY9A110A/CY9A110 Series 4. List of Pin Functions List of pin numbers The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR) to select the pin. Pin No LQFP-100 1 QFP-100 79 BGA-112 B1 1 1 I/O circuit type Pin name LQFP-64 QFN-64 LQFP-80 VCC Pin state type - P50 2 2 80 C1 2 INT00_0 AIN0_2 SIN3_1 - E H E H E H E H E I RTO10_0 (PPG10_0) MADATA00_1 P51 INT01_0 3 3 81 C2 BIN0_2 SOT3_1 (SDA3_1) 3 - RTO11_0 (PPG10_0) MADATA01_1 P52 INT02_0 4 4 82 B3 ZIN0_2 SCK3_1 (SCL3_1) 4 - RTO12_0 (PPG12_0) MADATA02_1 P53 SIN6_0 TIOA1_2 5 83 D1 5 - INT07_2 RTO13_0 (PPG12_0) MADATA03_1 P54 SOT6_0 (SDA6_0) 6 84 D2 6 - TIOB1_2 RTO14_0 (PPG14_0) MADATA04_1 Document Number: 002-04672 Rev. *F Page 13 of 110 CY9A110A/CY9A110 Series Pin No LQFP-100 QFP-100 BGA-112 Pin name LQFP-64 QFN-64 LQFP-80 I/O circuit type Pin state type P55 SCK6_0 (SCL6_0) 7 85 D3 7 - ADTG_1 E I E H E H E H E H E H E I RTO15_0 (PPG14_0) MADATA05_1 P56 8 86 D5 8 - INT08_2 DTTI1X_0 MADATA06_1 P30 9 87 E1 9 5 AIN0_0 TIOB0_1 INT03_2 - MADATA07_1 P31 BIN0_0 10 88 E2 10 6 TIOB1_1 SCK6_1 (SCL6_1) INT04_2 - MADATA08_1 P32 ZIN0_0 11 89 E3 11 7 TIOB2_1 SOT6_1 (SDA6_1) INT05_2 - MADATA09_1 P33 INT04_0 12 90 E4 12 8 TIOB3_1 SIN6_1 ADTG_6 - MADATA10_1 P34 13 91 F1 - - FRCK0_0 TIOB4_1 MADATA11_1 Document Number: 002-04672 Rev. *F Page 14 of 110 CY9A110A/CY9A110 Series Pin No LQFP-100 QFP-100 BGA-112 I/O circuit type Pin name LQFP-64 QFN-64 LQFP-80 Pin state type P35 IC03_0 14 92 F2 - - TIOB5_1 E H E H E H E H E I G I G I G I G I INT08_1 MADATA12_1 P36 IC02_0 15 93 F3 - - SIN5_2 INT09_1 MADATA13_1 P37 IC01_0 16 94 G1 - - SOT5_2 (SDA5_2) INT10_1 MADATA14_1 P38 IC00_0 17 95 G2 - - SCK5_2 (SCL5_2) INT11_1 MADATA15_1 P39 18 96 F4 13 9 DTTI0X_0 ADTG_2 P3A 19 97 G3 14 10 RTO00_0 (PPG00_0) TIOA0_1 P3B 20 98 H1 15 11 RTO01_0 (PPG00_0) TIOA1_1 P3C 21 99 H2 16 12 RTO02_0 (PPG02_0) TIOA2_1 P3D 22 100 G4 17 13 - - B2 - - RTO03_0 (PPG02_0) TIOA3_1 Document Number: 002-04672 Rev. *F VSS - Page 15 of 110 CY9A110A/CY9A110 Series Pin No LQFP-100 QFP-100 BGA-112 I/O circuit type Pin name LQFP-64 QFN-64 LQFP-80 Pin state type P3E 23 1 H3 18 14 RTO04_0 (PPG04_0) G I G I TIOA4_1 P3F 24 2 J2 19 15 RTO05_0 (PPG04_0) TIOA5_1 25 3 L1 20 16 VSS - 26 4 J1 - - VCC - P40 TIOA0_0 27 5 J4 - - RTO10_1 (PPG10_1) G H G H G I G I G I G I INT12_1 P41 TIOA1_0 28 6 L5 - - RTO11_1 (PPG10_1) INT13_1 P42 29 7 K5 - - TIOA2_0 RTO12_1 (PPG12_1) P43 TIOA3_0 30 8 J5 - - RTO13_1 (PPG12_1) ADTG_7 P44 21 31 9 H5 TIOA4_0 - MAD00_1 RTO14_1 (PPG14_1) - P45 22 32 10 L6 TIOA5_0 - MAD01_1 RTO15_1 (PPG14_1) - - K2 - - VSS - - - J3 - - VSS - - - H4 - - VSS - Document Number: 002-04672 Rev. *F Page 16 of 110 CY9A110A/CY9A110 Series Pin No LQFP-100 QFP-100 BGA-112 I/O circuit type Pin name LQFP-64 QFN-64 LQFP-80 33 11 L2 23 17 C - 34 12 L4 24 - VSS - 35 13 K1 25 18 VCC - 36 14 L3 26 19 37 15 K3 27 20 38 16 K4 28 21 P46 X0A P47 X1A INITX Pin state type D M D N B C E H E I E I E I E / I* I P48 DTTI1X_1 39 17 K6 29 - INT14_1 SIN3_2 MAD02_1 P49 22 TIOB0_0 AIN0_1 40 18 J6 30 IC10_1 - SOT3_2 (SDA3_2) MAD03_1 P4A 23 TIOB1_0 BIN0_1 41 19 L7 31 IC11_1 - SCK3_2 (SCL3_2) MAD04_1 P4B 24 42 20 K7 32 TIOB2_0 ZIN0_1 - IC12_1 MAD05_1 P4C TIOB3_0 25 43 21 H6 33 SCK7_1 (SCL7_1) AIN1_2 - Document Number: 002-04672 Rev. *F IC13_1 MAD06_1 Page 17 of 110 CY9A110A/CY9A110 Series Pin No LQFP-100 QFP-100 BGA-112 I/O circuit type Pin name LQFP-64 QFN-64 LQFP-80 Pin state type P4D TIOB4_0 26 44 22 J7 34 SOT7_1 (SDA7_1) E / I* I E / I* I C P J D A A A B BIN1_2 - FRCK1_1 MAD07_1 P4E TIOB5_0 45 23 K8 35 27 INT06_2 SIN7_1 ZIN1_2 46 24 K9 36 28 47 25 L8 37 29 MAD08_1 MD1 PE0 MD0 X0 48 26 L9 38 30 49 27 L10 39 31 50 28 L11 40 32 VSS - 51 29 K11 41 33 VCC - 52 30 J11 42 34 PE2 X1 PE3 P10 AN00 F K F L F K P11 AN01 53 31 J10 43 35 SIN1_1 INT02_1 FRCK0_2 - MAD09_1 P12 AN02 54 32 J8 44 36 SOT1_1 (SDA1_1) IC00_2 - MAD10_1 - - K10 - - VSS - - - J9 - - VSS - Document Number: 002-04672 Rev. *F Page 18 of 110 CY9A110A/CY9A110 Series Pin No LQFP-100 QFP-100 BGA-112 I/O circuit type Pin name LQFP-64 QFN-64 LQFP-80 Pin state type P13 AN03 55 33 H10 45 37 SCK1_1 (SCL1_1) F K F L F K F K F L IC01_2 - MAD11_1 P14 38 56 34 H9 46 AN04 INT03_1 IC02_2 - SIN0_1 MAD12_1 P15 39 57 35 H7 AN05 IC03_2 47 - SOT0_1 (SDA0_1) MAD13_1 P16 AN06 58 36 G10 48 - SCK0_1 (SCL0_1) MAD14_1 P17 59 37 G9 49 40 AN07 SIN2_2 INT04_1 - MAD15_1 60 38 H11 50 41 AVCC - 61 39 F11 51 42 AVRH - 62 40 G11 52 43 AVSS - P18 63 41 G8 53 44 - AN08 SOT2_2 (SDA2_2) F K F K MAD16_1 P19 64 - 42 - F10 H8 Document Number: 002-04672 Rev. *F 54 - 45 AN09 SCK2_2 (SCL2_2) - MAD17_1 - VSS - Page 19 of 110 CY9A110A/CY9A110 Series Pin No LQFP-100 QFP-100 BGA-112 I/O circuit type Pin name LQFP-64 QFN-64 LQFP-80 Pin state type P1A AN10 65 43 F9 55 - SIN4_1 INT05_1 F L F K F K F K F K F K IC00_1 MAD18_1 P1B AN11 66 44 E11 56 - SOT4_1 (SDA4_1) IC01_1 MAD19_1 P1C AN12 67 45 E10 - - SCK4_1 (SCL4_1) IC02_1 MAD20_1 P1D AN13 68 46 F8 - - CTS4_1 IC03_1 MAD21_1 P1E AN14 69 47 E9 - - RTS4_1 DTTI0X_1 MAD22_1 P1F AN15 70 48 D11 - - ADTG_5 FRCK0_1 MAD23_1 - - B10 - - VSS - - - C9 - - VSS - Document Number: 002-04672 Rev. *F Page 20 of 110 CY9A110A/CY9A110 Series Pin No LQFP-100 QFP-100 BGA-112 I/O circuit type Pin name LQFP-64 QFN-64 LQFP-80 Pin state type P23 57 71 49 46 D10 SCK0_0 (SCL0_0) TIOA7_1 - - E I E I E H E H RTO00_1 (PPG00_1) P22 72 50 E8 58 47 SOT0_0 (SDA0_0) TIOB7_1 - ZIN1_1 P21 73 51 C11 59 48 SIN0_0 INT06_1 - BIN1_1 P20 INT05_0 74 52 C10 60 - CROUT_0 AIN1_1 MAD24_1 75 53 A11 - - VSS - 76 54 A10 - - VCC - 77 55 A9 61 49 - P00 TRSTX E E E E E E E E E E E F MCSX7_1 P01 78 56 B9 62 50 TCK SWCLK 79 57 B11 63 51 - P02 TDI MCSX6_1 P03 80 58 A8 64 52 TMS SWDIO P04 81 59 B8 65 53 TDO SWO P05 TRACED0 82 60 C8 - - TIOA5_2 SIN4_2 INT00_1 MCSX5_1 - - D8 Document Number: 002-04672 Rev. *F - - VSS - Page 21 of 110 CY9A110A/CY9A110 Series Pin No LQFP-100 QFP-100 BGA-112 I/O circuit type Pin name LQFP-64 QFN-64 LQFP-80 Pin state type P06 TRACED1 TIOB5_2 83 61 D9 - - SOT4_2 (SDA4_2) E F E G E G E G E / I* H E / I* I E / I* I INT01_1 MCSX4_1 P07 66 84 62 A7 ADTG_0 - - MCLKOUT_1 TRACED2 SCK4_2 (SCL4_2) P08 TRACED3 85 63 B7 - - TIOA0_2 CTS4_2 MCSX3_1 P09 TRACECLK 86 64 C7 - - TIOB0_2 RTS4_2 MCSX2_1 P0A 54 87 65 D7 67 SIN4_0 INT00_2 - FRCK1_0 MCSX1_1 P0B 55 88 66 A6 68 SOT4_0 (SDA4_0) TIOB6_1 - IC10_0 MCSX0_1 P0C 56 89 67 B6 69 SCK4_0 (SCL4_0) TIOA6_1 - IC11_0 MALE_1 - - D4 - - VSS - - - C3 - - VSS - Document Number: 002-04672 Rev. *F Page 22 of 110 CY9A110A/CY9A110 Series Pin No LQFP-100 QFP-100 BGA-112 I/O circuit type Pin name LQFP-64 QFN-64 LQFP-80 Pin state type P0D RTS4_0 90 68 C6 70 - TIOA3_2 E I E I E J E H E I E I E / I* H IC12_0 MDQM0_1 P0E CTS4_0 91 69 A5 71 - TIOB3_2 IC13_0 MDQM1_1 P0F 92 70 B5 72 57 NMIX CROUT_1 P63 93 71 D6 73 - INT03_0 MWEX_1 P62 94 72 C5 74 58 SCK5_0 (SCL5_0) ADTG_3 - MOEX_1 P61 95 73 B4 75 59 SOT5_0 (SDA5_0) TIOB2_2 P60 96 74 C4 76 60 SIN5_0 TIOA2_2 INT15_1 - MRDY_1 97 75 A4 77 61 VCC - 98 76 A3 78 62 P80 H O 99 77 A2 79 63 P81 H O 100 78 A1 80 64 VSS - *: 5V tolerant I/O on CY9AF115MA/NA and CY9AF116MA/NA Document Number: 002-04672 Rev. *F Page 23 of 110 CY9A110A/CY9A110 Series List of pin functions The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR) to select the pin. Pin No Module ADC Pin name Function BGA-112 LQFP-80 LQFP-64 QFN-64 84 62 A7 66 - ADTG_1 7 85 D3 7 - ADTG_2 18 96 F4 13 9 94 72 C5 74 58 ADTG_4 A/D converter external trigger input pin - - - - - ADTG_5 70 48 D11 - - ADTG_6 12 90 E4 12 8 ADTG_7 30 8 J5 - - ADTG_8 - - - - - AN00 52 30 J11 42 34 AN01 53 31 J10 43 35 AN02 54 32 J8 44 36 AN03 55 33 H10 45 37 AN04 56 34 H9 46 38 AN05 57 35 H7 47 39 AN06 58 36 G10 48 - AN07 59 37 G9 49 40 AN08 A/D converter analog input pin. ANxx describes ADC ch.xx. 63 41 G8 53 44 AN09 64 42 F10 54 45 AN10 65 43 F9 55 - AN11 66 44 E11 56 - AN12 67 45 E10 - - AN13 68 46 F8 - - AN14 69 47 E9 - - AN15 70 48 D11 - - TIOA0_0 27 5 J4 - - 19 97 G3 14 10 85 63 B7 - - 40 18 J6 30 22 9 87 E1 9 5 86 64 C7 - - 28 6 L5 - - 20 98 H1 15 11 5 83 D1 5 - 41 19 L7 31 23 10 88 E2 10 6 6 84 D2 6 - TIOA0_1 Base timer ch.0 TIOA pin TIOA0_2 TIOB0_0 TIOB0_1 Base timer ch.0 TIOB pin TIOB0_2 Base Timer 1 QFP-100 ADTG_0 ADTG_3 Base Timer 0 LQFP-100 TIOA1_0 TIOA1_1 Base timer ch.1 TIOA pin TIOA1_2 TIOB1_0 TIOB1_1 Base timer ch.1 TIOB pin TIOB1_2 Document Number: 002-04672 Rev. *F Page 24 of 110 CY9A110A/CY9A110 Series Pin No Module Base Timer 2 Pin name TIOA2_0 BGA-112 LQFP-80 LQFP-64 QFN-64 K5 - - 21 99 H2 16 12 TIOA2_2 96 74 C4 76 60 TIOB2_0 42 20 K7 32 24 TIOA2_1 Base timer ch.2 TIOA pin 11 89 E3 11 7 TIOB2_2 95 73 B4 75 59 TIOA3_0 30 8 J5 - - TIOA3_1 Base timer ch.2 TIOB pin 22 100 G4 17 13 TIOA3_2 Base timer ch.3 TIOA pin 90 68 C6 70 - TIOB3_0 43 21 H6 33 25 12 90 E4 12 8 91 69 A5 71 - 31 9 H5 21 - 23 1 H3 18 14 - - - - - 44 22 J7 34 26 13 91 F1 - - - - - - - 32 10 L6 22 - 24 2 J2 19 15 TIOA5_2 82 60 C8 - - TIOB5_0 45 23 K8 35 27 14 92 F2 - - Base timer ch.3 TIOB pin TIOB3_2 TIOA4_0 TIOA4_1 Base timer ch.4 TIOA pin TIOA4_2 TIOB4_0 TIOB4_1 Base timer ch.4 TIOB pin TIOB4_2 Base Timer 5 QFP-100 7 TIOB3_1 Base Timer 4 LQFP-100 29 TIOB2_1 Base Timer 3 Function TIOA5_0 TIOA5_1 TIOB5_1 Base timer ch.5 TIOA pin Base timer ch.5 TIOB pin 83 61 D9 - - Base Timer 6 TIOB5_2 TIOA6_1 Base timer ch.6 TIOA pin 89 67 B6 69 56 TIOB6_1 Base timer ch.6 TIOB pin 88 66 A6 68 55 Base Timer 7 TIOA7_0 - - - - - 71 49 D10 57 46 TIOA7_2 - - - - - TIOB7_0 - - - - - 72 50 E8 58 47 - - - - - TIOA7_1 TIOB7_1 Base timer ch.7 TIOA pin Base timer ch.7 TIOB pin TIOB7_2 Document Number: 002-04672 Rev. *F Page 25 of 110 CY9A110A/CY9A110 Series Pin No Module Debugger Pin name SWCLK SWDIO Function Serial wire debug interface clock input Serial wire debug interface data input / output QFP-100 BGA-112 LQFP-80 LQFP-64 QFN-64 78 56 B9 62 50 80 58 A8 64 52 SWO Serial wire viewer output 81 59 B8 65 53 TCK JTAG test clock input 78 56 B9 62 50 TDI JTAG test data input 79 57 B11 63 51 TDO JTAG debug data output 81 59 B8 65 53 TMS JTAG test mode state input/output 80 58 A8 64 52 TRACECLK Trace CLK output of ETM 86 64 C7 - - 82 60 C8 - - 83 61 D9 - - 84 62 A7 - - 85 63 B7 - - TRACED0 TRACED1 TRACED2 Trace data output of ETM TRACED3 TRSTX External Bus LQFP-100 77 55 A9 61 49 MAD00_1 31 9 H5 21 - MAD01_1 32 10 L6 22 - MAD02_1 39 17 K6 29 - MAD03_1 40 18 J6 30 - MAD04_1 41 19 L7 31 - MAD05_1 42 20 K7 32 - MAD06_1 43 21 H6 33 - MAD07_1 44 22 J7 34 - MAD08_1 45 23 K8 35 - MAD09_1 53 31 J10 43 - MAD10_1 54 32 J8 44 - MAD11_1 55 33 H10 45 - 56 34 H9 46 - MAD13_1 57 35 H7 47 - MAD14_1 58 36 G10 48 - MAD15_1 59 37 G9 49 - MAD16_1 63 41 G8 53 - MAD17_1 64 42 F10 54 - MAD18_1 65 43 F9 55 - MAD19_1 66 44 E11 56 - MAD20_1 67 45 E10 - - MAD21_1 68 46 F8 - - MAD22_1 69 47 E9 - - MAD23_1 70 48 D11 - - MAD24_1 74 52 C10 60 - MAD12_1 JTAG test reset input External bus interface address bus Document Number: 002-04672 Rev. *F Page 26 of 110 CY9A110A/CY9A110 Series Pin No Module External Bus Pin name Function LQFP-100 QFP-100 BGA-112 LQFP-80 LQFP-64 QFN-64 MCSX0_1 88 66 A6 68 - MCSX1_1 87 65 D7 67 - MCSX2_1 86 64 C7 - - MCSX3_1 85 63 B7 - - MCSX4_1 External bus interface chip select output pin 83 61 D9 - - MCSX5_1 82 60 C8 - - MCSX6_1 79 57 B11 63 - MCSX7_1 77 55 A9 61 - MDQM0_1 90 68 C6 70 - 91 69 A5 71 - 94 72 C5 74 - 93 71 D6 73 - MADATA00_1 2 80 C1 2 - MADATA01_1 3 81 C2 3 - MADATA02_1 4 82 B3 4 - MADATA03_1 5 83 D1 5 - MADATA04_1 6 84 D2 6 - MADATA05_1 7 85 D3 7 - MADATA06_1 8 86 D5 8 - MADATA07_1 9 87 E1 9 - MDQM1_1 MOEX_1 MWEX_1 MADATA08_1 External bus interface byte mask signal output External bus interface read enable signal for SRAM External bus interface write enable signal for SRAM External bus interface data bus 10 88 E2 10 - MADATA09_1 11 89 E3 11 - MADATA10_1 12 90 E4 12 - MADATA11_1 13 91 F1 - - MADATA12_1 14 92 F2 - - MADATA13_1 15 93 F3 - - MADATA14_1 16 94 G1 - - MADATA15_1 17 95 G2 - - 89 67 B6 69 - 96 84 74 62 C4 A7 76 66 - MALE_1 MRDY_1 MCLKOUT_1 Address Latch enable signal for multiplex External RDY input signal External bus clock output Document Number: 002-04672 Rev. *F Page 27 of 110 CY9A110A/CY9A110 Series Pin No Module External Interrupt Pin name Function INT00_0 LQFP-100 QFP-100 BGA-112 LQFP-80 LQFP-64 QFN-64 2 80 C1 2 2 82 60 C8 - - INT00_2 87 65 D7 67 54 INT01_0 External interrupt request 01 input pin 3 81 C2 3 3 83 61 D9 - - External interrupt request 02 input pin 4 82 B3 4 4 53 31 J10 43 35 93 71 D6 73 - 56 34 H9 46 38 9 87 E1 9 5 12 90 E4 12 8 59 37 G9 49 40 INT04_2 10 88 E2 10 6 INT05_0 74 52 C10 60 - 65 43 F9 55 - INT05_2 11 89 E3 11 7 INT06_1 73 51 C11 59 48 45 23 K8 35 27 5 83 D1 5 - 14 92 F2 - - 8 86 D5 8 - 15 93 F3 - - 16 94 G1 - - 17 95 G2 - - 27 5 J4 - - 28 6 L5 - - 39 17 K6 29 - 96 74 C4 76 60 92 70 B5 72 57 INT00_1 INT01_1 INT02_0 INT02_1 External interrupt request 00 input pin INT03_0 INT03_1 External interrupt request 03 input pin INT03_2 INT04_0 INT04_1 INT05_1 INT06_2 INT07_2 INT08_1 INT08_2 INT09_1 INT10_1 INT11_1 INT12_1 INT13_1 INT14_1 INT15_1 NMIX External interrupt request 04 input pin External interrupt request 05 input pin External interrupt request 06 input pin External interrupt request 07 input pin External interrupt request 08 input pin External interrupt request 09 input pin External interrupt request 10 input pin External interrupt request 11 input pin External interrupt request 12 input pin External interrupt request 13 input pin External interrupt request 14 input pin External interrupt request 15 input pin Non-Maskable Interrupt input Document Number: 002-04672 Rev. *F Page 28 of 110 CY9A110A/CY9A110 Series Pin No Module GPIO Pin name P00 P01 P02 P03 P04 P05 P06 P07 P08 P09 P0A P0B P0C P0D P0E P0F P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P1A P1B P1C P1D P1E P1F P20 P21 P22 P23 Function General-purpose I/O port 0 General-purpose I/O port 1 General-purpose I/O port 2 Document Number: 002-04672 Rev. *F LQFP-100 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 52 53 54 55 56 57 58 59 63 64 65 66 67 68 69 70 74 73 72 71 QFP-100 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 30 31 32 33 34 35 36 37 41 42 43 44 45 46 47 48 52 51 50 49 BGA-112 LQFP-80 LQFP-64 QFN-64 A9 B9 B11 A8 B8 C8 D9 A7 B7 C7 D7 A6 B6 C6 A5 B5 J11 J10 J8 H10 H9 H7 G10 G9 G8 F10 F9 E11 E10 F8 E9 D11 C10 C11 E8 D10 61 62 63 64 65 66 67 68 69 70 71 72 42 43 44 45 46 47 48 49 53 54 55 56 60 59 58 57 49 50 51 52 53 54 55 56 57 34 35 36 37 38 39 40 44 45 48 47 46 Page 29 of 110 CY9A110A/CY9A110 Series Pin No Module GPIO Pin name P30 P31 P32 P33 P34 P35 P36 P37 P38 P39 P3A P3B P3C P3D P3E P3F P40 P41 P42 P43 P44 P45 P46 P47 P48 P49 P4A P4B P4C P4D P4E P50 P51 P52 P53 P54 P55 P56 P60 P61 P62 P63 P80 P81 PE0 PE2 PE3 Function General-purpose I/O port 3 General-purpose I/O port 4 General-purpose I/O port 5 General-purpose I/O port 6 General-purpose I/O port 8 General-purpose I/O port E Document Number: 002-04672 Rev. *F LQFP-100 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 27 28 29 30 31 32 36 37 39 40 41 42 43 44 45 2 3 4 5 6 7 8 96 95 94 93 98 99 46 48 49 QFP-100 87 88 89 90 91 92 93 94 95 96 97 98 99 100 1 2 5 6 7 8 9 10 14 15 17 18 19 20 21 22 23 80 81 82 83 84 85 86 74 73 72 71 76 77 24 26 27 BGA-112 LQFP-80 LQFP-64 QFN-64 E1 E2 E3 E4 F1 F2 F3 G1 G2 F4 G3 H1 H2 G4 H3 J2 J4 L5 K5 J5 H5 L6 L3 K3 K6 J6 L7 K7 H6 J7 K8 C1 C2 B3 D1 D2 D3 D5 C4 B4 C5 D6 A3 A2 K9 L9 L10 9 10 11 12 13 14 15 16 17 18 19 21 22 26 27 29 30 31 32 33 34 35 2 3 4 5 6 7 8 76 75 74 73 78 79 36 38 39 5 6 7 8 9 10 11 12 13 14 15 19 20 22 23 24 25 26 27 2 3 4 60 59 58 62 63 28 30 31 Page 30 of 110 CY9A110A/CY9A110 Series Pin No Module MultiFunction Serial 0 Pin name SIN0_0 SIN0_1 SOT0_0 (SDA0_0) SOT0_1 (SDA0_1) SCK0_0 (SCL0_0) SCK0_1 (SCL0_1) MultiFunction Serial 1 SIN1_1 SOT1_1 (SDA1_1) SCK1_1 (SCL1_1) Multi Function Serial 2 SIN2_2 SOT2_2 (SDA2_2) SCK2_2 (SCL2_2) Multi Function Serial 3 SIN3_1 SIN3_2 SOT3_1 (SDA3_1) SOT3_2 (SDA3_2) SCK3_1 (SCL3_1) SCK3_2 (SCL3_2) Function Multifunction serial interface ch.0 input pin Multifunction serial interface ch.0 output pin. This pin operates as SOT0 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA0 when it is used in an I2C (operation mode 4). Multifunction serial interface ch.0 clock I/O pin. This pin operates as SCK0 when it is used in a CSIO (operation mode 2) and as SCL0 when it is used in an I2C (operation mode 4). Multifunction serial interface ch.1 input pin Multifunction serial interface ch.1 output pin. This pin operates as SOT1 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA1 when it is used in an I2C (operation mode 4). Multifunction serial interface ch.1 clock I/O pin. This pin operates as SCK1 when it is used in a CSIO (operation mode 2) and as SCL1 when it is used in an I2C (operation mode 4). Multifunction serial interface ch.2 input pin Multifunction serial interface ch.2 output pin. This pin operates as SOT2 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA2 when it is used in an I2C (operation mode 4). Multifunction serial interface ch.2 clock I/O pin. This pin operates as SCK2 when it is used in a CSIO (operation mode 2) and as SCL2 when it is used in an I2C (operation mode 4). Multifunction serial interface ch.3 input pin Multifunction serial interface ch.3 output pin. This pin operates as SOT3 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA3 when it is used in an I2C (operation mode 4). Multifunction serial interface ch.3 clock I/O pin. This pin operates as SCK3 when it is used in a CSIO (operation mode 2) and as SCL3 when it is used in an I2C (operation mode 4). Document Number: 002-04672 Rev. *F LQFP-100 QFP-100 BGA-112 LQFP-80 LQFP-64 QFN-64 73 51 C11 59 48 56 34 H9 46 - 72 50 E8 58 47 57 35 H7 47 - 71 49 D10 57 46 58 36 G10 48 - 53 31 J10 43 35 54 32 J8 44 36 55 33 H10 45 37 59 37 G9 49 40 63 41 G8 53 44 64 42 F10 54 45 2 39 80 17 C1 K6 2 29 2 - 3 81 C2 3 3 40 18 J6 30 - 4 82 B3 4 4 41 19 L7 31 - Page 31 of 110 CY9A110A/CY9A110 Series Pin No Module MultiFunction Serial 4 Pin name Function SIN4_0 QFP-100 BGA-112 LQFP-80 LQFP-64 QFN-64 87 65 D7 67 54 65 43 F9 55 - 82 60 C8 - - 88 66 A6 68 55 66 44 E11 56 - 83 61 D9 - - 89 67 B6 69 56 67 45 E10 - - 84 62 A7 - - 90 68 C6 70 - 69 47 E9 - - 86 64 C7 - - 91 69 A5 71 - 68 46 F8 - - CTS4_2 85 63 B7 - - SIN5_0 96 74 C4 76 60 15 93 F3 - - 95 73 B4 75 59 16 94 G1 - - 94 72 C5 74 58 17 95 G2 - - SIN4_1 Multifunction serial interface ch.4 input pin SIN4_2 SOT4_0 (SDA4_0) SOT4_1 (SDA4_1) SOT4_2 (SDA4_2) SCK4_0 (SCL4_0) SCK4_1 (SCL4_1) SCK4_2 (SCL4_2) Multifunction serial interface ch.4 output pin. This pin operates as SOT4 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA4 when it is used in an I2C (operation mode 4). Multifunction serial interface ch.4 clock I/O pin. This pin operates as SCK4 when it is used in a CSIO (operation mode 2) and as SCL4 when it is used in an I2C (operation mode 4). RTS4_0 RTS4_1 Multifunction serial interface ch.4 RTS output pin RTS4_2 CTS4_0 CTS4_1 MultiFunction Serial 5 LQFP-100 SIN5_2 SOT5_0 (SDA5_0) SOT5_2 (SDA5_2) SCK5_0 (SCL5_0) SCK5_2 (SCL5_2) Multifunction serial interface ch.4 CTS input pin Multifunction serial interface ch.5 input pin Multifunction serial interface ch.5 output pin. This pin operates as SOT5 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA5 when it is used in an I2C (operation mode 4). Multifunction serial interface ch.5 clock I/O pin. This pin operates as SCK5 when it is used in a CSIO (operation mode 2) and as SCL5 when it is used in an I2C (operation mode 4). Document Number: 002-04672 Rev. *F Page 32 of 110 CY9A110A/CY9A110 Series Pin No Module MultiFunction Serial 6 Pin name SIN6_0 SIN6_1 SOT6_0 (SDA6_0) SOT6_1 (SDA6_1) SCK6_0 (SCL6_0) SCK6_1 (SCL6_1) MultiFunction Serial 7 SIN7_1 SOT7_1 (SDA7_1) SCK7_1 (SCL7_1) Function Multifunction serial interface ch.6 input pin Multifunction serial interface ch.6 output pin. This pin operates as SOT6 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA6 when it is used in an I2C (operation mode 4). Multifunction serial interface ch.6 clock I/O pin. This pin operates as SCK6 when it is used in a CSIO (operation mode 2) and as SCL6 when it is used in an I2C (operation mode 4). Multifunction serial interface ch.7 input pin Multifunction serial interface ch.7 output pin. This pin operates as SOT7 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA7 when it is used in an I2C (operation mode 4). Multifunction serial interface ch.7 clock I/O pin. This pin operates as SCK7 when it is used in a CSIO (operation mode 2) and as SCL7 when it is used in an I2C (operation mode 4). Document Number: 002-04672 Rev. *F LQFP-100 QFP-100 BGA-112 LQFP-80 LQFP-64 QFN-64 5 83 D1 5 - 12 90 E4 12 8 6 84 D2 6 - 11 89 E3 11 7 7 85 D3 7 - 10 88 E2 10 6 45 23 K8 35 27 44 22 J7 34 26 43 21 H6 33 25 Page 33 of 110 CY9A110A/CY9A110 Series Pin No Module MultiFunction Timer 0 Pin name DTTI0X_0 DTTI0X_1 Function Input signal of waveform generator to control outputs RTO00 to RTO05 of multi-function timer 0 FRCK0_0 FRCK0_1 16-bit free-run timer external clock input pin LQFP-100 QFP-100 BGA-112 LQFP-80 LQFP-64 QFN-64 18 96 F4 13 9 69 47 E9 - - 13 91 F1 - - 70 48 D11 - - FRCK0_2 53 31 J10 43 35 IC00_0 17 95 G2 - - IC00_1 65 43 F9 55 - IC00_2 54 32 J8 44 36 IC01_0 16 94 G1 - - IC01_1 66 44 E11 56 - 55 33 H10 45 37 IC01_2 IC02_0 16-bit input capture input pin of multifunction timer 0. ICxx describes channel number. 15 93 F3 - - IC02_1 67 45 E10 - - IC02_2 56 34 H9 46 38 IC03_0 14 92 F2 - - IC03_1 68 46 F8 - - IC03_2 57 35 H7 47 39 19 97 G3 14 10 71 49 D10 - - 20 98 H1 15 11 21 99 H2 16 12 22 100 G4 17 13 23 1 H3 18 14 24 2 J2 19 15 RTO00_0 (PPG00_0) RTO00_1 (PPG00_1) RTO01_0 (PPG00_0) RTO02_0 (PPG02_0) RTO03_0 (PPG02_0) RTO04_0 (PPG04_0) RTO05_0 (PPG04_0) Waveform generator output of multifunction timer 0. This pin operates as PPG00 when it is used in PPG 0 output mode. Waveform generator output of multifunction timer 0. This pin operates as PPG00 when it is used in PPG 0 output mode. Waveform generator output of multifunction timer 0. This pin operates as PPG02 when it is used in PPG 0 output mode. Waveform generator output of multifunction timer 0. This pin operates as PPG02 when it is used in PPG 0 output mode. Waveform generator output of multifunction timer 0. This pin operates as PPG04 when it is used in PPG 0 output mode. Waveform generator output of multifunction timer 0. This pin operates as PPG04 when it is used in PPG 0 output mode. Document Number: 002-04672 Rev. *F Page 34 of 110 CY9A110A/CY9A110 Series Pin No Module MultiFunction Timer 1 Pin name DTTI1X_0 DTTI1X_1 FRCK1_0 FRCK1_1 Function LQFP-100 QFP-100 BGA-112 LQFP-80 LQFP-64 QFN-64 Input signal of waveform generator to control outputs RTO10 to RTO15 of multi-function timer 1 8 86 D5 8 - 39 17 K6 29 - 16-bit free-run timer ch.1 external clock input pin 87 65 D7 67 - 44 22 J7 34 - IC10_0 88 66 A6 68 - IC10_1 40 18 J6 30 - IC11_0 89 67 B6 69 - 41 19 L7 31 - IC11_1 IC12_0 16-bit input capture input pin of multifunction timer 1. ICxx describes channel number. 90 68 C6 70 - IC12_1 42 20 K7 32 - IC13_0 91 69 A5 71 - IC13_1 43 21 H6 33 - Waveform generator output of multifunction timer 1. This pin operates as PPG10 when it is used in PPG 1 output mode. 2 80 C1 2 - 27 5 J4 - - Waveform generator output of multifunction timer 1. This pin operates as PPG10 when it is used in PPG 1 output mode. 3 81 C2 3 - 28 6 L5 - - Waveform generator output of multifunction timer 1. This pin operates as PPG12 when it is used in PPG 1 output mode. 4 82 B3 4 - 29 7 K5 - - Waveform generator output of multifunction timer 1. This pin operates as PPG12 when it is used in PPG 1 output mode. 5 83 D1 5 - 30 8 J5 - - Waveform generator output of multifunction timer 1. This pin operates as PPG14 when it is used in PPG 1 output mode. 6 84 D2 6 - 31 9 H5 21 - Waveform generator output of multifunction timer 1. This pin operates as PPG14 when it is used in PPG 1 output mode. 7 85 D3 7 - 32 10 L6 22 - RTO10_0 (PPG10_0) RTO10_1 (PPG10_1) RTO11_0 (PPG10_0) RTO11_1 (PPG10_1) RTO12_0 (PPG12_0) RTO12_1 (PPG12_1) RTO13_0 (PPG12_0) RTO13_1 (PPG12_1) RTO14_0 (PPG14_0) RTO14_1 (PPG14_1) RTO15_0 (PPG14_0) RTO15_1 (PPG14_1) Document Number: 002-04672 Rev. *F Page 35 of 110 CY9A110A/CY9A110 Series Pin No Module Quadrature Position/ Revolution Counter 0 Pin name Function AIN0_0 QFP-100 BGA-112 LQFP-80 LQFP-64 QFN-64 9 87 E1 9 5 40 18 J6 30 22 AIN0_2 2 80 C1 2 2 BIN0_0 10 88 E2 10 6 AIN0_1 BIN0_1 QPRC ch.0 AIN input pin 41 19 L7 31 23 BIN0_2 3 81 C2 3 3 ZIN0_0 11 89 E3 11 7 42 20 K7 32 24 4 82 B3 4 4 74 52 C10 60 - 43 21 H6 33 25 73 51 C11 59 - 44 22 J7 34 26 72 50 E8 58 - 45 23 K8 35 27 ZIN0_1 QPRC ch.0 BIN input pin QPRC ch.0 ZIN input pin ZIN0_2 Quadrature Position/ Revolution Counter 1 LQFP-100 AIN1_1 AIN1_2 BIN1_1 BIN1_2 ZIN1_1 ZIN1_2 QPRC ch.1 AIN input pin QPRC ch.1 BIN input pin QPRC ch.1 ZIN input pin Document Number: 002-04672 Rev. *F Page 36 of 110 CY9A110A/CY9A110 Series Pin No Module Reset Pin name INITX LQFP-64 QFN-64 21 47 25 L8 37 29 46 24 K9 36 28 1 26 35 51 76 97 25 34 50 75 100 48 36 49 37 79 4 13 29 54 75 3 12 28 53 78 26 14 27 15 B1 J1 K1 K11 A10 A4 B2 L1 K2 J3 H4 L4 L11 K10 J9 H8 B10 C9 A11 D8 D4 C3 A1 L9 L3 L10 K3 1 25 41 77 20 24 40 80 38 26 39 27 1 18 33 61 16 32 64 30 19 31 20 Built-in high-speed CR-osc clock output port 74 52 C10 60 - 92 70 B5 72 57 A/D converter analog power supply pin A/D converter analog reference voltage input pin 60 38 H11 50 41 61 39 F11 51 42 AVSS A/D converter GND pin 62 40 G11 52 43 C Power supply stabilization capacity pin 33 11 L2 23 17 VCC VCC VCC VCC VCC VCC VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS X0 X0A X1 X1A CROUT_1 AVCC AVRH Analog GND C pin LQFP-80 28 CROUT_0 Analog Power BGA-112 K4 MD1 Clock QFP-100 16 MD0 GND External Reset Input. A reset is valid when INITX="L" Mode 0 pin. During normal operation, MD0="L" must be input. During serial programming to flash memory, MD0="H" must be input. Mode 1 pin. During serial programming to flash memory, MD1="L" must be input. Power supply pin Power supply pin Power supply pin Power supply pin Power supply pin Power supply pin GND pin GND pin GND pin GND pin GND pin GND pin GND pin GND pin GND pin GND pin GND pin GND pin GND pin GND pin GND pin GND pin GND pin Main clock (oscillation) input pin Sub clock (oscillation) input pin Main clock (oscillation) I/O pin Sub clock (oscillation) I/O pin LQFP-100 38 Mode Power Function Note: − While this device contains a Test Access Port (TAP) based on the IEEE 1149.1-2001 JTAG standard, it is not fully compliant to all requirements of that standard. This device may contain a 32-bit device ID that is the same as the 32-bit device ID in other devices with different functionality. The TAP pins may also be configurable for purposes other than access to the TAP controller. Document Number: 002-04672 Rev. *F Page 37 of 110 CY9A110A/CY9A110 Series 5. I/O Circuit Type Type A Circuit Remarks It is possible to select the main oscillation / GPIO function Pull-up resistor P-ch When the main oscillation is selected. P-ch Digital output X1 • Oscillation feedback resistor : Approximately 1 MΩ • With Standby mode control When the GPIO is selected. N-ch Digital output R Pull-up resistor control Digital input • • • • • CMOS level output. CMOS level hysteresis input With pull-up resistor control With standby mode control Pull-up resistor : Approximately 50 kΩ • IOH = -4 mA, IOL = 4 mA Standby mode control Feedback Clock input resistor Standby mode control Digital input Standby mode control Pull-up resistor R P-ch P-ch Digital output N-ch Digital output X0 Pull-up resistor control B • CMOS level hysteresis input • Pull-up resistor : Approximately 50 kΩ Pull-up resistor Digital input Document Number: 002-04672 Rev. *F Page 38 of 110 CY9A110A/CY9A110 Series Type C Circuit Remarks Digital input • Open drain output • CMOS level hysteresis input Digital output N-ch D It is possible to select the sub oscillation / GPIO function Pull-up resistor P-ch When the sub oscillation is selected. P-ch Digital output X1A • Oscillation feedback resistor : Approximately 5 MΩ • With Standby mode control When the GPIO is selected. N-ch Digital output R Pull-up resistor control Digital input • • • • • CMOS level output. CMOS level hysteresis input With pull-up resistor control With standby mode control Pull-up resistor : Approximately 50 kΩ • IOH = -4 mA, IOL = 4 mA Standby mode control Feedback Clock input resistor Standby mode control Digital input Standby mode control Pull-up resistor R P-ch P-ch Digital output N-ch Digital output X0A Pull-up resistor control Document Number: 002-04672 Rev. *F Page 39 of 110 CY9A110A/CY9A110 Series Type E Circuit Remarks • • • • • P-ch P-ch N-ch Digital output Digital output CMOS level output CMOS level hysteresis input With pull-up resistor control With standby mode control Pull-up resistor : Approximately 50 kΩ • IOH=-4 mA, IOL=4 mA • When this pin is used as an I2C pin, the digital output P-ch transistor is always off • +B input is available R Pull-up resistor control Digital input Standby mode control F P-ch R P-ch Digital output N-ch Digital output • • • • • • • CMOS level output CMOS level hysteresis input With input control Analog input With pull-up resistor control With standby mode control Pull-up resistor : Approximately 50 kΩ • IOH=-4 mA, IOL=4 mA • When this pin is used as an I2C pin, the digital output P-ch transistor is always off • +B input is available Pull-up resistor control Digital input Standby mode control Analog input Input control Document Number: 002-04672 Rev. *F Page 40 of 110 CY9A110A/CY9A110 Series Type G Circuit Remarks • • • • • CMOS level output CMOS level hysteresis input With pull-up resistor control With standby mode control Pull-up resistor : Approximately 50 kΩ • IOH=-12 mA, IOL= 12 mA • +B input is available P-ch P-ch N-ch Digital output Digital output R Pull-up resistor control Digital input Standby mode control H • • • • CMOS level output CMOS level hysteresis input With standby mode control IOH = -20.5 mA, IOL = 18.5 mA Digital output N-ch Digital output R Digital input Standby mode control Document Number: 002-04672 Rev. *F Page 41 of 110 CY9A110A/CY9A110 Series Type I Circuit Remarks • • • • • • P-ch Digital output N-ch Digital output CMOS level output CMOS level hysteresis input 5V tolerant With standby mode control IOH=-4 mA, IOL= 4 mA When this pin is used as an I2C pin, the digital output P-ch transistor is always off R Digital input Standby mode control J CMOS level hysteresis input Mode Input Document Number: 002-04672 Rev. *F Page 42 of 110 CY9A110A/CY9A110 Series 6. Handling Precautions Any semiconductor devices have inherently a certain rate of failure. The possibility of failure is greatly affected by the conditions in which they are used (circuit conditions, environmental conditions, etc.). This page describes precautions that must be observed to minimize the chance of failure and to obtain higher reliability from your Cypress semiconductor devices. 6.1 Precautions for Product Design This section describes precautions when designing electronic equipment using semiconductor devices. Absolute Maximum Ratings Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of certain established limits, called absolute maximum ratings. Do not exceed these ratings. Recommended Operating Conditions Recommended operating conditions are normal operating ranges for the semiconductor device. All the device's electrical characteristics are warranted when operated within these ranges. Always use semiconductor devices within the recommended operating conditions. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the datasheet. Users considering application outside the listed conditions are advised to contact their sales representative beforehand. Processing and Protection of Pins These precautions must be followed when handling the pins which connect semiconductor devices to power supply and input/output functions. 1. Preventing Over-Voltage and Over-Current Conditions Exposure to voltage or current levels in excess of maximum ratings at any pin is likely to cause deterioration within the device, and in extreme cases leads to permanent damage of the device. Try to prevent such overvoltage or over-current conditions at the design stage. 2. Protection of Output Pins Shorting of output pins to supply pins or other output pins, or connection to large capacitance can cause large current flows. Such conditions if present for extended periods of time can damage the device. Therefore, avoid this type of connection. 3. Handling of Unused Input Pins Unconnected input pins with very high impedance levels can adversely affect stability of operation. Such pins should be connected through an appropriate resistance to a power supply pin or ground pin. Latch-up Semiconductor devices are constructed by the formation of P-type and N-type areas on a substrate. When subjected to abnormally high voltages, internal parasitic PNPN junctions (called thyristor structures) may be formed, causing large current levels in excess of several hundred mA to flow continuously at the power supply pin. This condition is called latch-up. CAUTION: The occurrence of latch-up not only causes loss of reliability in the semiconductor device, but can cause injury or damage from high heat, smoke or flame. To prevent this from happening, do the following: 1. Be sure that voltages applied to pins do not exceed the absolute maximum ratings. This should include attention to abnormal noise, surge levels, etc. 2. Be sure that abnormal current flows do not occur during the power-on sequence. Observance of Safety Regulations and Standards Most countries in the world have established standards and regulations regarding safety, protection from electromagnetic interference, etc. Customers are requested to observe applicable regulations and standards in the design of products. Fail-Safe Design Any semiconductor devices have inherently a certain rate of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of overcurrent levels and other abnormal operating conditions. Document Number: 002-04672 Rev. *F Page 43 of 110 CY9A110A/CY9A110 Series Precautions Related to Usage of Devices Cypress semiconductor devices are intended for use in standard applications (computers, office automation and other office equipment, industrial, communications, and measurement equipment, personal or household devices, etc.). CAUTION: Customers considering the use of our products in special applications where failure or abnormal operation may directly affect human lives or cause physical injury or property damage, or where extremely high levels of reliability are demanded (such as aerospace systems, atomic energy controls, sea floor repeaters, vehicle operating controls, medical devices for life support, etc.) are requested to consult with sales representatives before such use. The company will not be responsible for damages arising from such use without prior approval. 6.2 Precautions for Package Mounting Package mounting may be either lead insertion type or surface mount type. In either case, for heat resistance during soldering, you should only mount under Cypress recommended conditions. For detailed information about mount conditions, contact your sales representative. Lead Insertion Type Mounting of lead insertion type packages onto printed circuit boards may be done by two methods: direct soldering on the board, or mounting by using a socket. Direct mounting onto boards normally involves processes for inserting leads into through-holes on the board and using the flow soldering (wave soldering) method of applying liquid solder. In this case, the soldering process usually causes leads to be subjected to thermal stress in excess of the absolute ratings for storage temperature. Mounting processes should conform to Cypress recommended mounting conditions. If socket mounting is used, differences in surface treatment of the socket contacts and IC lead surfaces can lead to contact deterioration after long periods. For this reason, it is recommended that the surface treatment of socket contacts and IC leads be verified before mounting. Surface Mount Type Surface mount packaging has longer and thinner leads than lead-insertion packaging, and therefore leads are more easily deformed or bent. The use of packages with higher pin counts and narrower pin pitch results in increased susceptibility to open connections caused by deformed pins, or shorting due to solder bridges. You must use appropriate mounting techniques. Cypress recommends the solder reflow method, and has established a ranking of mounting conditions for each product. Users are advised to mount packages in accordance with Cypress ranking of recommended conditions. Lead-Free Packaging CAUTION: When ball grid array (BGA) packages with Sn-Ag-Cu balls are mounted using Sn-Pb eutectic soldering, junction strength may be reduced under some conditions of use. Storage of Semiconductor Devices Because plastic chip packages are formed from plastic resins, exposure to natural environmental conditions will cause absorption of moisture. During mounting, the application of heat to a package that has absorbed moisture can cause surfaces to peel, reducing moisture resistance and causing packages to crack. To prevent, do the following: 1. Avoid exposure to rapid temperature changes, which cause moisture to condense inside the product. Store products in locations where temperature changes are slight. 2. Use dry boxes for product storage. Products should be stored below 70% relative humidity, and at temperatures between 5°C and 30°C. When you open Dry Package that recommends humidity 40% to 70% relative humidity. 3. When necessary, Cypress packages semiconductor devices in highly moisture-resistant aluminum laminate bags, with a silica gel desiccant. Devices should be sealed in their aluminum laminate bags for storage. 4. Avoid storing packages where they are exposed to corrosive gases or high levels of dust. Document Number: 002-04672 Rev. *F Page 44 of 110 CY9A110A/CY9A110 Series Baking Packages that have absorbed moisture may be de-moisturized by baking (heat drying). Follow the Cypress recommended conditions for baking. Condition: 125°C/24 h Static Electricity Because semiconductor devices are particularly susceptible to damage by static electricity, you must take the following precautions: 1. Maintain relative humidity in the working environment between 40% and 70%. Use of an apparatus for ion generation may be needed to remove electricity. 2. Electrically ground all conveyors, solder vessels, soldering irons and peripheral equipment. 3. Eliminate static body electricity by the use of rings or bracelets connected to ground through high resistance (on the level of 1 MΩ). Wearing of conductive clothing and shoes, use of conductive floor mats and other measures to minimize shock loads is recommended. 4. Ground all fixtures and instruments, or protect with anti-static measures. 5. Avoid the use of styrofoam or other highly static-prone materials for storage of completed board assemblies. 6.3 Precautions for Use Environment Reliability of semiconductor devices depends on ambient temperature and other conditions as described above. For reliable performance, do the following: 1. Humidity Prolonged use in high humidity can lead to leakage in devices as well as printed circuit boards. If high humidity levels are anticipated, consider anti-humidity processing. 2. Discharge of Static Electricity When high-voltage charges exist close to semiconductor devices, discharges can cause abnormal operation. In such cases, use anti-static measures or processing to prevent discharges. 3. Corrosive Gases, Dust, or Oil Exposure to corrosive gases or contact with dust or oil may lead to chemical reactions that will adversely affect the device. If you use devices in such conditions, consider ways to prevent such exposure or to protect the devices. 4. Radiation, Including Cosmic Radiation Most devices are not designed for environments involving exposure to radiation or cosmic radiation. Users should provide shielding as appropriate. 5. Smoke, Flame CAUTION: Plastic molded devices are flammable, and therefore should not be used near combustible substances. If devices begin to smoke or burn, there is danger of the release of toxic gases. Customers considering the use of Cypress products in other special environmental conditions should consult with sales representatives. Document Number: 002-04672 Rev. *F Page 45 of 110 CY9A110A/CY9A110 Series 7. Handling Devices Power supply pins In products with multiple VCC and VSS pins, respective pins at the same potential are interconnected within the device in order to prevent malfunctions such as latch-up. However, all of these pins should be connected externally to the power supply or ground lines in order to reduce electromagnetic emission levels, to prevent abnormal operation of strobe signals caused by the rise in the ground level, and to conform to the total output current rating. Moreover, connect the current supply source with each Power supply pin and GND pin of this device at low impedance. It is also advisable that a ceramic capacitor of approximately 0.1 µF be connected as a bypass capacitor between each Power supply pin and GND pin, between AVCC pin and AVSS pin near this device. Stabilizing power supply voltage A malfunction may occur when the power supply voltage fluctuates rapidly even though the fluctuation is within the recommended operating conditions of the VCC power supply voltage. As a rule, with voltage stabilization, suppress the voltage fluctuation so that the fluctuation in VCC ripple (peak-to-peak value) at the commercial frequency (50 Hz/60 Hz) does not exceed 10% of the VCC value in the recommended operating conditions, and the transient fluctuation rate does not exceed 0.1 V/μs when there is a momentary fluctuation on switching the power supply. Crystal oscillator circuit Noise near the X0/X1 and X0A/X1A pins may cause the device to malfunction. Design the printed circuit board so that X0/X1, X0A/X1A pins, the crystal oscillator, and the bypass capacitor to ground are located as close to the device as possible. It is strongly recommended that the PC board artwork be designed such that the X0/X1 and X0A/X1A pins are surrounded by ground plane as this is expected to produce stable operation. Evaluate oscillation of your using crystal oscillator by your mount board. Using an external clock When using an external clock, the clock signal should be driven to the X0, X0A pin only and the X1, X1A pin should be kept open. • Example of Using an External Clock Device X0(X0A) Open X1(X1A) Handling when using Multi-function serial pin as I2C pin If it is using the multi-function serial pin as I2C pins, P-ch transistor of digital output is always disabled. However, I 2C pins need to keep the electrical characteristic like other pins and not to connect to the external I 2C bus system with power OFF. Document Number: 002-04672 Rev. *F Page 46 of 110 CY9A110A/CY9A110 Series C Pin This series contains the regulator. Be sure to connect a smoothing capacitor (C S) for the regulator between the C pin and the GND pin. Please use a ceramic capacitor or a capacitor of equivalent frequency characteristics as a smoothing capacitor. However, some laminated ceramic capacitors have the characteristics of capacitance variation due to thermal fluctuation (F characteristics and Y5V characteristics). Please select the capacitor that meets the specifications in the operating conditions to use by evaluating the temperature characteristics of a capacitor. A smoothing capacitor of about 4.7 μF would be recommended for this series. C Device CS VSS GND Mode pins (MD0) Connect the MD pin (MD0) directly to VCC or VSS pins. Design the printed circuit board such that the pull-up/down resistor stays low, as well as the distance between the mode pins and VCC pins or VSS pins is as short as possible and the connection impedance is low, when the pins are pulled-up/down such as for switching the pin level and rewriting the Flash memory data. It is because of preventing the device erroneously switching to test mode due to noise. Notes on power-on Turn power on/off in the following order or at the same time. If not using the A/D converter, connect AVCC = VCC and AVSS = VSS. Turning on : VCC → AVCC → AVRH Turning off : AVRH → AVCC → VCC Serial Communication There is a possibility to receive wrong data due to the noise or other causes on the serial communication. Therefore, design a printed circuit board so as to avoid noise. Consider the case of receiving wrong data due to noise, perform error detection such as by applying a checksum of data at the end. If an error is detected, retransmit the data Differences in features among the products with different memory sizes and between Flash memory products and MASK products The electric characteristics including power consumption, ESD, latch-up, noise characteristics, and oscillation characteristics among the products with different memory sizes and between Flash products and MASK products are different because chip layout and memory structures are different. If you are switching to use a different product of the same series, please make sure to evaluate the electric characteristics. Document Number: 002-04672 Rev. *F Page 47 of 110 CY9A110A/CY9A110 Series 8. Block Diagram MB9AF111LA/MA/NA, F112LA/MA/NA/L, F114LA/MA/NA/L, F115MA/NA, F116MA/NA TRSTX,TCK, TDI,TMS TDO TRACED[3:0], TRACECLK SWJ-DP ETM*1 TPIU*1 ROM Table SRAM0 8/16 Kbyte Cortex-M3 Core I @40 MHz(Max) D Multi-layer AHB (Max 40 MHz) NVIC Flash I/F Sys AHB-APB Bridge: APB0(Max 40 MHz) Dual-Timer WatchDog Timer (Software) Clock Reset Generator INITX WatchDog Timer (Hardware) Security On-Chip Flash 64/128/256/384/512 Kbyte SRAM1 8/16 Kbyte DMAC 8ch CSV X0 X1 X0A Main Osc Sub Osc PLL CR 4MHz AHB-AHB Bridge CLK Source Clock CR 100kHz MAD[24:0] CROUT AVCC, AVSS,AVRH External Bus I/F*2 12-bit A/D Converter x 3 MADATA[15:0] MCSX[7:0], MOEX,MWEX, MALE, MRDY, MCLKOUT, MDQM[1:0] Unit 0 AN[15:0] Unit 1 TIOB[7:0] AIN[1:0] BIN[1:0] QPRC 2ch. ZIN[1:0] A/D Activation Compare 3ch. IC0[3:0] IC1[3:0] FRCK[1:0] DTTI[1:0]X RTO0[5:0] RTO1[5:0] Power-On Reset Base Timer 16-bit 8ch. / 32-bit 4ch. 16-bit Input Capture 4ch. 16-bit Free-Run Timer 3ch. 16-bit Output Compare 6ch. LVD Ctrl AHB-APB Bridge : APB2 (Max 40 MHz) TIOA[7:0] Unit 2*2 AHB-APB Bridge : APB1 (Max 40 MHz) ADTGx Regulator Multi-Function Timer x 2 C IRQ-Monitor CRC Accelerator Watch Counter External Interrupt Controller 16-pin + NMI INT[15:0] NMIX MD[1:0] MODE-Ctrl GPIO Waveform Generator 3ch. 16-bit PPG 3ch. LVD Multi-Function Serial I/F 8ch. (with FIFO ch.4 to 7) 2 & HW flow control(ch.4)* PIN-Function-Ctrl P0[F:0], P1[F:0], . . . Px[x:0] SCK[7:0] SIN[7:0] SOT[7:0] CTS4 RTS4 *1: For the CY9AF111LA/MA, F112LA/MA, CY9AF114LA/MA, CY9AF115MA and CY9AF116MA, ETM is not available. *2: For the CY9AF111LA, F112LA and CY9AF114LA, the External Bus Interface and 12-bit A/D Converter (unit 2) are not available. And the Multi-function Serial Interface does not support hardware flow control in these products. Document Number: 002-04672 Rev. *F Page 48 of 110 CY9A110A/CY9A110 Series 9. Memory Size See “Memory Size” in “1. Product Lineup” to confirm the memory size. 10. Memory Map Memory Map (1) Peripherals Area 0x41FF_FFFF Reserved 0xFFFF_FFFF Reserved 0xE010_0000 0xE000_0000 Cortex-M3 Private Peripherals 0x4006_1000 0x4006_0000 0x4005_0000 0x4003_F000 Reserved 0x4003_B000 0x4003_A000 0x7000_0000 0x6000_0000 0x4003_9000 External Device Area 0x4003_8000 0x4003_7000 Reserved 0x4003_5000 32Mbytes Bit band alias 0x4003_4000 0x4400_0000 0x4200_0000 0x4000_0000 Peripherals 0x4003_3000 0x4003_2000 0x4003_1000 0x4003_0000 Reserved 0x2400_0000 0x2200_0000 32Mbytes Bit band alias Reserved 0x2008_0000 0x2000_0000 0x1FF8_0000 See the next page "nMemory Map (2),(3)" for the memory size details. 0x0010_2000 0x0010_0000 0x4002_F000 0x4002_E000 0x4002_8000 Security/CR Trim EXT-bus I/F Reserved Watch Counter CRC MFS Reserved LVD Reserved GPIO Reserved Int-Req.Read EXTI Reserved CR Trim Reserved A/DC 0x4002_6000 QPRC 0x4002_5000 Base Timer PPG 0x4002_2000 0x4002_1000 0x4002_0000 Reserved MFT Unit1 MFT Unit0 0x4001_6000 Flash 0x4001_5000 0x4001_3000 0x0000_0000 0x4001_2000 0x4001_1000 0x4001_0000 0x4000_1000 0x4000_0000 Document Number: 002-04672 Rev. *F Reserved 0x4002_7000 SRAM1 SRAM0 Reserved DMAC Dual Timer Reserved SW WDT HW WDT Clock/Reset Reserved Flash I/F Page 49 of 110 CY9A110A/CY9A110 Series Memory Map (2) MB9AF116MA/NA MB9AF115MA/NA 0x2008_0000 0x2008_0000 Reserved 0x1FFF_C000 SRAM1 16Kbytes 0x2000_0000 SRAM0 16Kbytes 0x1FFF_C000 0x2000_4000 SRAM1 16Kbytes 0x2000_0000 SRAM0 16Kbytes 0x1FFF_C000 Reserved 0x0010_2000 0x0010_0000 Reserved 0x2000_4000 Reserved 0x0010_1000 0x2008_0000 Reserved 0x2000_4000 0x2000_0000 MB9AF114LA/MA/NA MB9AF114L 0x0010_1000 0x0010_0000 SRAM0 16Kbytes Reserved 0x0010_2000 CR trimming Security SRAM1 16Kbytes 0x0010_2000 CR trimming Security 0x0010_1000 0x0010_0000 CR trimming Security Reserved 0x0008_0000 Reserved Reserved 0x0006_0000 SA10-13(64KBx4) 0x0000_0000 SA4-7(8KBx4) 0x0004_0000 SA10-11(64KBx2) SA8-9(48KBx2) 0x0000_0000 SA4-7(8KBx4) SA8-9(48KBx2) 0x0000_0000 Flash 256Kbytes SA8-9(48KBx2) Flash 384Kbytes Flash 512Kbytes SA10-15(64KBx6) SA4-7(8KBx4) See "CY9A310A/110A Series Flash programming Manual" for sector structure of Flash. Document Number: 002-04672 Rev. *F Page 50 of 110 CY9A110A/CY9A110 Series Memory Map (3) MB9AF112LA/MA/NA MB9AF112L MB9AF111LA/MA/NA 0x2008_0000 0x2008_0000 Reserved Reserved 0x2000_2000 0x2000_0000 0x1FFF_E000 0x2000_2000 SRAM1 8Kbytes SRAM0 8Kbytes SRAM1 8Kbytes SRAM0 8Kbytes 0x2000_0000 0x1FFF_E000 Reserved Reserved 0x0010_2000 0x0010_1000 0x0010_0000 0x0010_2000 CR trimming Security 0x0010_1000 0x0010_0000 CR trimming Security Reserved 0x0000_0000 SA4-7(8KBx4) 0x0001_0000 SA8-9(16KBx2) 0x0000_0000 SA4-7(8KBx4) Flash 64Kbytes SA8-9(48KBx2) Flash 128Kbytes 0x0002_0000 Reserved See "CY9A310A/110A Series Flash programming Manual" for sector structure of Flash. Document Number: 002-04672 Rev. *F Page 51 of 110 CY9A110A/CY9A110 Series Peripheral Address Map Start address End address Bus Peripherals 0x4000_0000H 0x4000_0FFFH 0x4000_1000H 0x4000_FFFFH 0x4001_0000H 0x4001_0FFFH Clock/Reset Control 0x4001_1000H 0x4001_1FFFH Hardware Watchdog timer 0x4001_2000H 0x4001_2FFFH 0x4001_3000H 0x4001_4FFFH 0x4001_5000H 0x4001_5FFFH Dual-Timer 0x4001_6000H 0x4001_FFFFH Reserved 0x4002_0000H 0x4002_0FFFH Multi-function timer unit0 0x4002_1000H 0x4002_1FFFH Multi-function timer unit1 0x4002_2000H 0x4002_3FFFH Reserved 0x4002_4000H 0x4002_4FFFH PPG 0x4002_5000H 0x4002_5FFFH 0x4002_6000H 0x4002_6FFFH 0x4002_7000H 0x4002_7FFFH A/D Converter 0x4002_8000H 0x4002_DFFFH Reserved 0x4002_E000H 0x4002_EFFFH Built-in CR trimming 0x4002_F000H 0x4002_FFFFH Reserved 0x4003_0000H 0x4003_0FFFH External Interrupt 0x4003_1000H 0x4003_1FFFH Interrupt Source Check Register 0x4003_2000H 0x4003_2FFFH Reserved 0x4003_3000H 0x4003_3FFFH GPIO 0x4003_4000H 0x4003_4FFFH Reserved 0x4003_5000H 0x4003_5FFFH 0x4003_6000H 0x4003_6FFFH 0x4003_7000H 0x4003_7FFFH Reserved 0x4003_8000H 0x4003_8FFFH Multi-function serial Interface 0x4003_9000H 0x4003_9FFFH CRC 0x4003_A000H 0x4003_AFFFH Watch Counter 0x4003_B000H 0x4003_EFFFH Reserved 0x4003_F000H 0x4003_FFFFH External Bus interface 0x4004_0000H 0x4004_FFFFH Reserved 0x4005_0000H 0x4005_FFFFH Reserved 0x4006_0000H 0x4006_0FFFH 0x4006_1000H 0x4006_1FFFH 0x4006_2000H 0x4006_2FFFH Reserved 0x4006_3000H 0x4006_3FFFH Reserved 0x4006_4000H 0x41FF_FFFFH Reserved Document Number: 002-04672 Rev. *F AHB APB0 APB1 Flash Memory I/F register Reserved Software Watchdog timer Reserved Base Timer Quadrature Position/Revolution Counter(QPRC) Low-Voltage Detector APB2 Reserved DMAC register AHB Reserved Page 52 of 110 CY9A110A/CY9A110 Series 11. Pin Status in Each CPU State The terms used for pin status have the following meanings.  INITX=0 This is the period when the INITX pin is the "L" level.  INITX=1 This is the period when the INITX pin is the "H" level.  SPL=0 This is the status that the standby pin level setting bit (SPL) in the standby mode control register (STB_CTL) is set to "0".  SPL=1 This is the status that the standby pin level setting bit (SPL) in the standby mode control register (STB_CTL) is set to "1".  Input enabled Indicates that the input function can be used.  Internal input fixed at "0" This is the status that the input function cannot be used. Internal input is fixed at "L".  Hi-Z Indicates that the pin drive transistor is disabled and the pin is put in the Hi-Z state.  Setting disabled Indicates that the setting is disabled.  Maintain previous state Maintains the state that was immediately prior to entering the current mode. If a built-in peripheral function is operating, the output follows the peripheral function. If the pin is being used as a port, that output is maintained.  Analog input is enabled Indicates that the analog input is enabled.  Trace output Indicates that the trace function can be used. Document Number: 002-04672 Rev. *F Page 53 of 110 CY9A110A/CY9A110 Series List of Pin Status Pin status type Function group Power-on reset or lowvoltage detection state Power supply unstable - INITX input state Device internal reset state Run mode or SLEEP mode state Timer mode or STOP mode state INITX=0 INITX=1 Power supply stable INITX=1 - - - SPL=0 Power supply stable Power supply stable INITX=1 SPL=1 GPIO selected Setting disabled Setting disabled Setting disabled Maintain previous state Maintain previous state Hi-Z/ Internal input fixed at "0" Main crystal oscillator input pin Input enabled Input enabled Input enabled Input enabled Input enabled Input enabled GPIO selected Setting disabled Setting disabled Setting disabled Maintain previous state Maintain previous state Hi-Z/ Internal input fixed at "0" Maintain previous state/ Hi-Z at oscillation stop*1/ Internal input fixed at "0" A Main crystal oscillator output pin Hi-Z/ Internal input fixed at "0"/ or Input enable Hi-Z/ Internal input fixed at "0" Hi-Z/ Internal input fixed at "0" Maintain previous state Maintain previous state/ Hi-Z at oscillation stop*1/ Internal input fixed at "0" C INITX input pin Pull-up/ Input enabled Pull-up/ Input enabled Pull-up/ Input enabled Pull-up/ Input enabled Pull-up/ Input enabled Pull-up/ Input enabled D Mode input pin Input enabled Input enabled Input enabled Input enabled Input enabled Input enabled JTAG selected Hi-Z Pull-up/ Input enabled Pull-up/ Input enabled Setting disabled Setting disabled Setting disabled Setting disabled Setting disabled Setting disabled B E GPIO selected Maintain previous state Maintain previous state Maintain previous state Trace selected External interrupt enabled selected F GPIO selected, or resource other than above selected Document Number: 002-04672 Rev. *F Hi-Z/ Internal input fixed at "0" Trace output Maintain previous state Maintain previous state Hi-Z Hi-Z/ Input enabled Hi-Z/ Input enabled Maintain previous state Hi-Z/ Internal input fixed at "0" Page 54 of 110 CY9A110A/CY9A110 Series Pin status type Function group Power-on reset or lowvoltage detection state Power supply unstable - Trace selected G H I J Setting disabled Device internal reset state INITX=0 INITX=1 - - - Setting disabled Timer mode or STOP mode state Power supply stable INITX=1 SPL=0 Setting disabled Hi-Z Hi-Z/ Input enabled Hi-Z/ Input enabled External interrupt enabled selected Setting disabled Setting disabled Setting disabled GPIO selected, or resource other than above selected Hi-Z Hi-Z/ Input enabled Hi-Z/ Input enabled GPIO selected, resource selected Hi-Z Hi-Z/ Input enabled Hi-Z/ Input enabled NMIX selected Setting disabled Setting disabled Setting disabled GPIO selected, or resource other than above selected Run mode or SLEEP mode state Power supply stable INITX=1 Power supply stable GPIO selected, or resource other than above selected SPL=1 Trace output Maintain previous state Maintain previous state Hi-Z/ Internal input fixed at "0" Maintain previous state Maintain previous state Maintain previous state Maintain previous state Maintain previous state Hi-Z/ Internal input fixed at "0" Hi-Z/ Internal input fixed at "0" Maintain previous state Maintain previous state Maintain previous state Hi-Z/ Internal input fixed at "0" Hi-Z Hi-Z/ Input enabled Hi-Z/ Input enabled Analog input selected Hi-Z Hi-Z/ Internal input fixed at "0"/ Analog input enabled Hi-Z/ Internal input fixed at "0"/ Analog input enabled Hi-Z/ Internal input fixed at "0"/ Analog input enabled Hi-Z/ Internal input fixed at "0"/ Analog input enabled Hi-Z/ Internal input fixed at "0"/ Analog input enabled GPIO selected, or resource other than above selected Setting disabled Setting disabled Setting disabled Maintain previous state Maintain previous state Hi-Z/ Internal input fixed at "0" External interrupt enabled selected Setting disabled Setting disabled Setting disabled Maintain previous state Maintain previous state Maintain previous state Analog input selected Hi-Z Hi-Z/ Internal input fixed at "0"/ Analog input enabled Hi-Z/ Internal input fixed at "0"/ Analog input enabled Hi-Z/ Internal input fixed at "0"/ Analog input enabled Hi-Z/ Internal input fixed at "0"/ Analog input enabled Hi-Z/ Internal input fixed at "0"/ Analog input enabled GPIO selected, or resource other than above selected Setting disabled Setting disabled Setting disabled Maintain previous state Maintain previous state Hi-Z/ Internal input fixed at "0" K L INITX input state Document Number: 002-04672 Rev. *F Page 55 of 110 CY9A110A/CY9A110 Series Pin status type Function group Power-on reset or lowvoltage detection state Power supply unstable - Power supply stable INITX=0 INITX=1 - - - Power supply stable INITX=1 SPL=0 SPL=1 Input enabled Input enabled Maintain previous state Maintain previous state Hi-Z/ Internal input fixed at "0" Hi-Z/ Internal input fixed at "0" Maintain previous state Maintain previous state/ Hi-Z at oscillation stop*2/ Internal input fixed at "0" Maintain previous state/ Hi-Z at oscillation stop*2/ Internal input fixed at "0" Hi-Z/ Input enabled Hi-Z/ Input enabled Maintain previous state Maintain previous state Hi-Z/ Internal input fixed at "0" Input enabled Input enabled Input enabled Input enabled Input enabled Input enabled Setting disabled Setting disabled Setting disabled Maintain previous state Maintain previous state Hi-Z/Input enabled Setting disabled Setting disabled Setting disabled Sub crystal oscillator input pin Input enabled Input enabled Input enabled GPIO selected Setting disabled Setting disabled Setting disabled Sub crystal oscillator output pin Hi-Z/ Internal input fixed at "0"/ or Input enabled Hi-Z/ Internal input fixed at "0" GPIO pin Hi-Z Mode input pin GPIO selected P Maintain previous state Input enabled Timer mode or STOP mode state Maintain previous state GPIO selected N Run mode or SLEEP mode state Power supply stable INITX=1 Hi-Z/ Internal input fixed at "0" M O INITX input state Device internal reset state *1: Oscillation is stopped at sub timer mode, low-speed CR timer mode, and stop mode. *2: Oscillation is stopped at stop mode. Document Number: 002-04672 Rev. *F Page 56 of 110 CY9A110A/CY9A110 Series 12. Electrical Characteristics 12.1 Absolute Maximum Ratings Parameter Rating Symbol Power supply voltage*1, *2 Analog power supply voltage*1, *3 Analog reference voltage*1, *3 VCC AVCC AVRH Input voltage*1 VI Min Unit Max VSS - 0.5 VSS - 0.5 VSS - 0.5 VSS + 6.5 VSS + 6.5 VSS + 6.5 V V V VSS - 0.5 VCC + 0.5 (≤ 6.5 V) V VSS - 0.5 Analog pin input voltage*1 VIA VSS - 0.5 Output voltage*1 VO VSS - 0.5 Clamp maximum current ICLAMP -2 Clamp total maximum current Σ[ICLAMP] Remarks VSS + 6.5 AVCC + 0.5 (≤ 6.5 V) VCC + 0.5 (≤ 6.5 V) +2 V mA *7 +20 mA *7 10 20 39 4 12 18.5 100 50 - 10 mA mA mA mA mA mA mA mA mA 4mA type 12mA type P80, P81 4mA type 12mA type P80, P81 mA mA mA mA 12mA type P80, P81 4mA type 12mA type mA mA mA mW °C P80, P81 "L" level maximum output current*4 IOL - "L" level average output current*5 IOLAV - "L" level total maximum output current "L" level total average output current*6 ∑IOL ∑IOLAV - "H" level maximum output current*4 IOH - "H" level average output current*5 IOHAV - - 20 - 39 -4 - 12 "H" level total maximum output current "H" level total average output current*6 Power consumption Storage temperature ∑IOH ∑IOHAV PD TSTG - 55 - 20.5 - 100 - 50 300 + 150 5V tolerant V V 4mA type *1: These parameters are based on the condition that V SS = AVSS = 0.0 V. *2: VCC must not drop below VSS - 0.5 V. *3: Be careful not to exceed VCC + 0.5 V, for example, when the power is turned on. *4: The maximum output current is defined as the value of the peak current flowing through any one of the corresponding pins. *5: The average output current is defined as the average current value flowing through any one of the corresponding pins for a 100 ms period. *6: The total average output current is defined as the average current value flowing through all of corresponding pins for a 100 ms. Document Number: 002-04672 Rev. *F Page 57 of 110 CY9A110A/CY9A110 Series *7: • • • • • See “4. List of Pin Functions” and “5. I/O Circuit Type” about +B input available pin. Use within recommended operating conditions. Use at DC voltage (current) the +B input. The +B signal should always be applied a limiting resistance placed between the +B signal and the device. The value of the limiting resistance should be set so that when the +B signal is applied the input current to the device pin does not exceed rated values, either instantaneously or for prolonged periods. • Note that when the device drive current is low, such as in the low-power consumption modes, the +B input potential may pass through the protective diode and increase the potential at the VCC and AVCC pin, and this may affect other devices. • Note that if a +B signal is input when the device power supply is off (not fixed at 0 V), the power supply is provided from the pins, so that incomplete operation may result. • The following is a recommended circuit example (I/O equivalent circuit). Protection Diode VCC VCC Limiting resistor P-ch +B input(0V to 16V) Digital output N-ch Digital input R AVCC Analog input WARNING: − Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. Document Number: 002-04672 Rev. *F Page 58 of 110 CY9A110A/CY9A110 Series 12.2 Recommended Operating Conditions (VSS = AVSS = 0.0V) Parameter Symbol Value Conditions Min Max Unit Remarks Power supply voltage VCC - 2.7*2 5.5 V Analog power supply voltage AVCC - 2.7 5.5 V Analog reference voltage AVRH - 2.7 AVCC V Smoothing capacitor LQI100 LQH080 LQD064 LQG064 VNC064 LBC112 Operating temperature CS - 1 10 μF TA - - 40 + 105 °C - 40 + 105 °C TA When mounted on four-layer PCB When mounted on double-sided single-layer PCB - 40 + 105 °C ICC ≤ 35 mA - 40 + 85 °C ICC > 35 mA PQH100 AVCC = VCC For built-in regulator*1 *1: See "C Pin" in "7. Handling Devices" for the connection of the smoothing capacitor. *2: In between less than the minimum power supply voltage and low voltage reset/interrupt detection voltage or more, instruction execution and low voltage detection function by built-in High-speed CR(including Main PLL is used) or builtin Low-speed CR is possible to operate only. WARNING: − The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device's electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the datasheet. Users considering application outside the listed conditions are advised to contact their representatives beforehand. Document Number: 002-04672 Rev. *F Page 59 of 110 CY9A110A/CY9A110 Series 12.3 DC Characteristics 12.3.1 Current rating (VCC = AVCC= 2.7V to 5.5V, VSS = AVSS = 0V, TA = - 40°C to + 105°C) Parameter Symbol Pin name Conditions PLL RUN mode RUN mode current ICC High-speed CR RUN mode VCC Sub RUN mode Low-speed CR RUN mode SLEEP mode current ICCS PLL SLEEP mode High-speed CR SLEEP mode Sub SLEEP mode Low-speed CR SLEEP mode CPU: 40 MHz, Peripheral: 40 MHz, Flash 0 Wait FRWTR.RWT = 00 FSYNDN.SD = 000 *5 CPU: 40 MHz, Peripheral: 40 MHz, Flash 3 Wait FRWTR.RWT = 00 FSYNDN.SD = 011 *5 Value Typ*3 Max*4 Unit Remarks 32 41 mA *1 21 28 mA *1 3.9 7.7 mA *1 0.15 3.2 mA *1 0.2 3.3 mA *1 10 15 mA *1 Peripheral: 4 MHz *2 1.2 4.4 mA *1 Peripheral: 32 kHz *6 0.1 3.1 mA *1 Peripheral: 100 kHz 0.1 3.1 mA *1 CPU/ Peripheral: 4 MHz *2 Flash 0 Wait FRWTR.RWT = 00 FSYNDN.SD = 000 CPU/ Peripheral: 32 kHz Flash 0 Wait FRWTR.RWT = 00 FSYNDN.SD = 000 *6 CPU/ Peripheral: 100 kHz Flash 0 Wait FRWTR.RWT = 00 FSYNDN.SD = 000 Peripheral: 40 MHz *5 *1: When all ports are fixed. *2: When setting it to 4 MHz by trimming. *3: TA =+25°C, VCC=5.5 V *4: TA =+105°C, VCC=5.5 V *5: When using the crystal oscillator of 4 MHz(Including the current consumption of the oscillation circuit) *6: When using the crystal oscillator of 32 kHz(Including the current consumption of the oscillation circuit) Document Number: 002-04672 Rev. *F Page 60 of 110 CY9A110A/CY9A110 Series (Vcc = AVcc = 2.7V to 5.5V, Vss = AVss = 0V, TA = - 40°C to + 105°C) Parameter Pin name Symbol Main TIMER mode TIMER mode current ICCT VCC STOP mode current ICCH Value Typ*2 Max*2 Conditions Sub TIMER mode STOP mode TA = + 25°C, When LVD is off *3 TA = + 105°C, When LVD is off *3 TA = + 25°C, When LVD is off *4 TA = + 105°C, When LVD is off *4 TA = + 25°C, When LVD is off Ta = + 105°C, When LVD is off Unit Remarks 2.5 3 mA *1 - 6 mA *1 60 230 μA *1 - 3.1 mA *1 35 200 μA *1 - 3 mA *1 *1: When all ports are fixed. *2: VCC=5.5 V *3: When using the crystal oscillator of 4 MHz(Including the current consumption of the oscillation circuit) *4: When using the crystal oscillator of 32 kHz(Including the current consumption of the oscillation circuit) Low-Voltage Detection Current (VCC = 2.7V to 5.5V, VSS = 0V, TA = - 40°C to + 105°C) Parameter Low-voltage detection circuit (LVD) power supply current Symbol ICCLVD Pin name VCC Value Conditions At operation for interrupt Vcc = 5.5 V Typ 4 Max 7 Unit μA Remarks At not detect Flash Memory Current (VCC = 2.7V to 5.5V, VSS = 0V, TA = - 40°C to + 105°C) Parameter Flash memory write/erase current Symbol ICCFLASH Pin name VCC Value Conditions At Write/Erase Typ 11.4 Max 13.1 Unit Remarks mA A/D Converter Current (VCC = AVCC = 2.7V to 5.5V, VSS = AVSS = AVRL = 0V, TA = - 40°C to + 105°C) Parameter Power supply current Reference power supply current Symbol ICCAD ICCAVRH Document Number: 002-04672 Rev. *F Pin name AVCC AVRH Value Conditions Typ Max Unit At 1unit operation 0.57 0.72 mA At stop 0.06 20 μA At 1unit operation AVRH=5.5 V 1.1 1.96 mA At stop 0.06 4 μA Remarks Page 61 of 110 CY9A110A/CY9A110 Series 12.3.2 Pin Characteristics (VCC = AVCC = 2.7V to 5.5V, VSS = AVSS = 0V, TA = - 40°C to + 105°C) Parameter Symbol "H" level input voltage (hysteresis input) VIHS "L" level input voltage (hysteresis input) VILS Pin name CMOS hysteresis input pin, MD0,1 5V tolerant I/O pin CMOS hysteresis input pin, MD0,1 4mA type "H" level output voltage VOH 12mA type P80, P81 4mA type "L" level output voltage VOL 12mA type P80, P81 Input leak current Pull-up resistor value Input capacitance IIL - RPU Pull-up pin CIN Other than VCC, VSS, AVCC, AVSS, AVRH Document Number: 002-04672 Rev. *F Value Conditions Min Typ Max Unit - VCC × 0.8 - VCC + 0.3 V - VCC × 0.8 - VSS + 5.5 V - VSS - 0.3 - VCC × 0.2 V VCC - 0.5 - VCC V VCC - 0.5 - VCC V VCC - 0.4 - VCC V VSS - 0.4 V VSS - 0.4 V VSS - 0.4 V μA Vcc ≥ 4.5 V IOH = - 4 mA Vcc < 4.5 V IOH = - 2 mA Vcc ≥ 4.5 V IOH = - 12 mA Vcc < 4.5 V IOH = - 8 mA Vcc ≥ 4.5 V IOH = - 20.5 mA Vcc < 4.5 V IOH = - 13.0 mA Vcc ≥ 4.5 V IOL = 4 mA Vcc < 4.5 V IOL = 2 mA Vcc ≥ 4.5 V IOL = 12 mA Vcc < 4.5 V IOL = 8 mA Vcc ≥ 4.5 V IOL = 18.5 mA Vcc < 4.5 V IOL = 10.5 mA - -5 - +5 Vcc≥ 4.5 V 25 50 100 VCC