Please note that Cypress is an Infineon Technologies Company.
The document following this cover page is marked as “Cypress” document as this is the
company that originally developed the product. Please note that Infineon will continue
to offer the product to new and existing customers as part of the Infineon product
portfolio.
Continuity of document content
The fact that Infineon offers the following product as part of the Infineon product
portfolio does not lead to any changes to this document. Future revisions will occur
when appropriate, and any changes will be set out on the document history page.
Continuity of ordering part numbers
Infineon continues to support existing part numbers. Please continue to use the
ordering part numbers listed in the datasheet for ordering.
www.infineon.com
CY9A140NB Series
32-bit ARM® Cortex®-M3
FM3 Microcontroller
The CY9A140NB Series are highly integrated 32-bit microcontrollers dedicated for embedded controllers with low-power
consumption mode and competitive cost.
These series are based on the ARM Cortex-M3 Processor with on-chip Flash memory and SRAM, and have peripheral functions
such as various timers, ADCs, and Communication Interfaces (UART, CSIO, I2C).
The products which are described in this datasheet are placed into TYPE6 product categories in FM3 Family Peripheral Manual.
Features
32-bit ARM® Cortex®-M3 Core
External Bus Interface*
Processor version: r2p1
Supports SRAM, NOR Flash memory device
Up to 40 MHz Frequency Operation
Up to 8 chip selects
Integrated Nested Vectored Interrupt Controller (NVIC):
8-/16-bit Data width
1 NMI (non-maskable interrupt) and 48 peripheral interrupts
and 16 priority levels
24-bit System timer (Sys Tick): System timer for OS task
Up to 25-bit Address bit
Maximum area size: Up to 256 MB
Supports Address/Data multiplex
management
Supports external RDY function
On-chip Memories
*: CY9AF141LB, F142LB and F144LB do not support
External Bus Interface.
[Flash memory]
Dual operation Flash memory
Dual
Operation Flash memory has the upper bank and the
lower bank.
So, this series could implement erase, write and read
operations
for each bank simultaneously.
Main area: Up to 256 Kbytes (Up to 240 Kbytes upper bank
+ 16 Kbytes lower bank)
Work area: 32 Kbytes (lower bank)
Read cycle: 0 wait-cycle
Multi-function Serial Interface (Max 8 channels)
4 channels with 16 steps×9-bit FIFO (ch.4 to ch.7), 4
channels without FIFO (ch.0 to ch.3)
Operation mode is selectable from the followings for each
channel.
UART
CSIO
I2C
Security function for code protection
[UART]
[SRAM]
Full-duplex double buffer
This Series on-chip SRAM is composed of two independent
SRAM (SRAM0, SRAM1). SRAM0 is connected to I-code bus
and D-code bus of Cortex-M3 core. SRAM1 is connected to
System bus.
Selection with or without parity supported
Built-in dedicated baud rate generator
External clock available as a serial clock
Hardware Flow control*: Automatically control the
SRAM0: Up to 16 KB
transmission by CTS/RTS (only ch.4)
SRAM1: Up to 16 KB
Various error detection functions available (parity errors,
framing errors, and overrun errors)
*: CY9AF141LB, F142LB and F144LB do not support
Hardware Flow control.
Cypress Semiconductor Corporation
Document Number: 002-05637 Rev. *C
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised May 17, 2019
CY9A140NB Series
[CSIO]
General-Purpose I/O Port
Full-duplex double buffer
This series can use its pins as general-purpose I/O ports when
they are not used for external bus or peripherals. Moreover, the
port relocate function is built in. It can set which I/O port the
peripheral function can be allocated to.
Built-in dedicated baud rate generator
Overrun error detection function available
[I2C]
Standard-mode (Max 100 kbps) / Fast-mode (Max 400 kbps)
supported
Capable of pull-up control per pin
Capable of reading pin level directly
Built-in the port relocate function
DMA Controller (8 channels)
Up to 83 fast general-purpose I/O Ports@100 pin Package
The DMA Controller has an independent bus from the CPU, so
CPU and DMA Controller can process simultaneously.
Some ports are 5 V tolerant I/O.
8 independently configured and operated channels
Transfer can be started by software or request from the
built-in peripherals
Transfer address area: 32-bit (4 GB)
Transfer mode: Block transfer/Burst transfer/Demand
transfer
See Pin Description to confirm the corresponding pins.
Dual Timer (32-/16-bit Down Counter)
The Dual Timer consists of two programmable 32-/16-bit down
counters.
Operation mode is selectable from the followings for each
channel.
Free-running
Transfer data type: byte/half-word/word
Periodic (=Reload)
Transfer block count: 1 to 16
One-shot
Number of transfers: 1 to 65536
A/D Converter (Max 24 channels)
HDMI-CEC/Remote Control Receiver (Up to 2
channels)
[12-bit A/D Converter]
HDMI-CEC transmitter
Successive Approximation type
Built-in 2 units
Conversion time: 2.0 μs @ 2.7 V to 3.6 V
Priority conversion available (priority at 2 levels)
Scanning conversion mode
Built-in FIFO for conversion data storage (for SCAN
conversion: 16 steps, for Priority conversion: 4 steps)
Base Timer (Max 8 channels)
Operation mode is selectable from the followings for each
channel.
Header
block automatic transmission by judging Signal
free
Generating status interrupt by detecting Arbitration lost
Generating START, EOM, ACK automatically to output
CEC transmission by setting 1 byte data
Generating transmission status interrupt when transmitting
1 block (1 byte data and EOM/ACK)
HDMI-CEC receiver
Automatic ACK
Line
reply function available
error detection function available
Remote control receiver
4
bytes reception buffer
code detection function available
Repeat
16-bit PWM timer
16-bit PPG timer
16-/32-bit reload timer
16-/32-bit PWC timer
Document Number: 002-05637 Rev. *C
Page 2 of 118
CY9A140NB Series
Real-time clock (RTC)
The Real-time clock can count
Year/Month/Day/Hour/Minute/Second/A day of the week from
00 to 99.
The interrupt function with specifying date and time
(Year/Month/Day/Hour/Minute) is available. This function is
also available by specifying only Year, Month, Day, Hour or
Minute.
Timer interrupt function after set time or each set time.
Capable of rewriting the time with continuing the time count.
Leap year automatic count is available.
Watch Counter
The Watch counter is used for wake up from sleep and timer
mode.
Interval timer: up to 64 s (Max) @ Sub Clock: 32.768 kHz
External Interrupt Controller Unit
Up to 16 external interrupt input pins
Include one non-maskable interrupt (NMI) input pin
Watchdog Timer (2 channels)
A watchdog timer can generate interrupts or a reset when a
time-out value is reached.
This series consists of two different watchdogs, a Hardware
watchdog and a Software watchdog.
The Hardware watchdog timer is clocked by the built-in
low-speed CR oscillator. Therefore, the Hardware watchdog is
active in any low-power consumption modes except RTC, Stop,
Deep Standby RTC and Deep Standby Stop modes.
CRC (Cyclic Redundancy Check) Accelerator
The CRC accelerator calculates the CRC which has a heavy
software processing load, and achieves a reduction of the
integrity check processing load for reception data and storage.
Clock and Reset
[Clocks]
Selectable from five clock sources (2 external oscillators, 2
built-in CR oscillators, and Main PLL).
Main Clock:
4 MHz to 48 MHz
Sub Clock:
32.768 kHz
Built-in high-speed CR Clock: 4 MHz
Built-in low-speed CR Clock:
100 kHz
Main PLL Clock
[Resets]
Reset requests from INITX pin
Power on reset
Software reset
Watchdog timers reset
Low-voltage detection reset
Clock Super Visor reset
Clock Super Visor (CSV)
Clocks generated by built-in CR oscillators are used to
supervise abnormality of the external clocks.
External clock failure (clock stop) is detected, reset is
asserted.
External frequency anomaly is detected, interrupt or reset is
asserted.
Low-Voltage Detector (LVD)
This Series includes 2-stage monitoring of voltage on the VCC
pins. When the voltage falls below the voltage that has been
set, Low-Voltage Detector generates an interrupt or reset.
LVD1: error reporting via interrupt
LVD2: auto-reset operation
CCITT CRC16 and IEEE-802.3 CRC32 are supported.
CCITT CRC16 Generator Polynomial: 0x1021
IEEE-802.3 CRC32 Generator Polynomial: 0x04C11DB7
Document Number: 002-05637 Rev. *C
Page 3 of 118
CY9A140NB Series
Low-Power Consumption Mode
Six low-power consumption modes supported.
Debug
Sleep
Serial Wire JTAG Debug Port (SWJ-DP)
Timer
Embedded Trace Macrocells (ETM)*
RTC
*: CY9AF141LB/MB, F142LB/MB and F144LB/MB support
only SWJ-DP.
Stop
Deep Standby RTC (selectable between keeping the value of
RAM and not)
Deep Standby Stop (selectable between keeping the value of
RAM and not)
Document Number: 002-05637 Rev. *C
Unique ID
Unique value of the device (41-bit) is set.
Power Supply
Wide range voltage: VCC = 1.65 V to 3.6 V
Page 4 of 118
CY9A140NB Series
Contents
1. Product Lineup .................................................................................................................................................................. 7
2. Packages ........................................................................................................................................................................... 8
3. Pin Assignment ................................................................................................................................................................. 9
4. List of Pin Functions....................................................................................................................................................... 16
5. I/O Circuit Type ............................................................................................................................................................... 39
6. Handling Precaution ....................................................................................................................................................... 44
7. Handling Devices ............................................................................................................................................................ 47
8. Block Diagram ................................................................................................................................................................. 49
9. Memory Size .................................................................................................................................................................... 50
10. Memory Map .................................................................................................................................................................... 50
11. Pin Status in Each CPU State ........................................................................................................................................ 53
12. Electrical Characteristics ............................................................................................................................................... 60
12.1 Absolute Maximum Ratings ......................................................................................................................................... 60
12.2 Recommended Operating Conditions ......................................................................................................................... 61
12.3 DC Characteristics ...................................................................................................................................................... 62
12.3.1 Current Rating .............................................................................................................................................................. 62
12.3.2 Pin Characteristics ....................................................................................................................................................... 65
12.4 AC Characteristics ....................................................................................................................................................... 66
12.4.1 Main Clock Input Characteristics .................................................................................................................................. 66
12.4.2 Sub Clock Input Characteristics ................................................................................................................................... 67
12.4.3 Built-in CR Oscillation Characteristics .......................................................................................................................... 67
12.4.4 Operating Conditions of Main PLL (In the case of using main clock for input of PLL) .................................................. 68
12.4.5 Operating Conditions of Main PLL (In the case of using the built-in High-speed CR for the input clock
of the Main PLL) ........................................................................................................................................................... 68
12.4.6 Reset Input Characteristics .......................................................................................................................................... 69
12.4.7 Power-on Reset Timing ................................................................................................................................................ 69
12.4.8 External Bus Timing ..................................................................................................................................................... 70
12.4.9 Base Timer Input Timing .............................................................................................................................................. 77
12.4.10 CSIO/UART Timing .................................................................................................................................................. 78
12.4.11 External Input Timing ................................................................................................................................................ 86
12.4.12 I2C Timing ................................................................................................................................................................. 87
12.4.13 ETM Timing .............................................................................................................................................................. 88
12.4.14 JTAG Timing............................................................................................................................................................. 89
12.5 12-bit A/D Converter .................................................................................................................................................... 90
12.6 Low-Voltage Detection Characteristics ........................................................................................................................ 93
12.6.1 Low-Voltage Detection Reset ....................................................................................................................................... 93
12.6.2 Interrupt of Low-Voltage Detection ............................................................................................................................... 94
12.7 Flash Memory Write/Erase Characteristics ................................................................................................................. 95
12.7.1 Write / Erase time......................................................................................................................................................... 95
12.7.2 Erase/write cycles and data hold time .......................................................................................................................... 95
12.8 Return Time from Low-Power Consumption Mode ...................................................................................................... 96
12.8.1 Return Factor: Interrupt/WKUP .................................................................................................................................... 96
12.8.2 Return Factor: Reset .................................................................................................................................................... 98
13. Ordering Information .................................................................................................................................................... 100
14. Package Dimensions .................................................................................................................................................... 102
15. Errata.............................................................................................................................................................................. 111
16. Major Changes .............................................................................................................................................................. 115
Document Number: 002-05637 Rev. *C
Page 5 of 118
CY9A140NB Series
Document History ............................................................................................................................................................... 117
Sales, Solutions, and Legal Information ........................................................................................................................... 118
Document Number: 002-05637 Rev. *C
Page 6 of 118
CY9A140NB Series
1. Product Lineup
Memory Size
Product name
On-chip
Flash
memory
On-chip
SRAM
CY9AF141LB/MB/NB
CY9AF142LB/MB/NB
CY9AF144LB/MB/NB
Main area
64 KB
128 KB
256 KB
Work area
32 KB
32 KB
32 KB
SRAM0
8 KB
8 KB
16 KB
SRAM1
Total
8 KB
16 KB
8 KB
16 KB
16 KB
32 KB
Function
Product name
Pin count
CY9AF141LB
CY9AF142LB
CY9AF144LB
64
CPU
Freq.
Power supply voltage range
DMAC
External Bus Interface
-
Multi-function Serial Interface
(UART/CSIO/I2C)
CY9AF141MB
CY9AF142MB
CY9AF144MB
80/96
100/112
Cortex-M3
40 MHz
1.65 V to 3.6 V
8 ch.
Addr: 21-bit (Max)
Addr: 25-bit (Max)
R/W Data: 8-bit (Max)
R/W Data: 8-/16-bit (Max)
CS: 4 (Max)
CS: 8 (Max)
Support: SRAM, NOR Flash
Support: SRAM,
memory
NOR Flash memory
8 ch. (Max)
ch.4 to ch.7: FIFO (16steps × 9-bit)
ch.0 to ch.3: No FIFO
Base Timer
(PWC/Reload timer/PWM/PPG)
8 ch. (Max)
Dual Timer
1 unit
HDMI-CEC/ Remote Control Receiver
Real-Time Clock
Watch Counter
CRC Accelerator
Watchdog timer
External Interrupts
I/O ports
12-bit A/D converter
CSV (Clock Super Visor)
LVD (Low-Voltage Detector)
High-speed
Built-in CR
Low-speed
Debug Function
Unique ID
CY9AF141NB
CY9AF142NB
CY9AF144NB
2 ch. (Max)
1 unit
1 unit
Yes
1ch. (SW) + 1ch. (HW)
11 pins (Max) +
NMI × 1
66 pins (Max)
17 ch. (2 units)
Yes
2 ch.
4 MHz
100 kHz
8 pins (Max) +
NMI × 1
51 pins (Max)
12 ch. (2 units)
SWJ-DP
16 pins (Max) +
NMI × 1
83 pins (Max)
24 ch. (2 units)
SWJ-DP/ETM
Yes
Note:
−
All signals of the peripheral function in each product cannot be allocated by limiting the pins of package.
It is necessary to use the port relocate function of the I/O port according to your function use.
See 12. Electrical Characteristics 12.4. AC Characteristics 12.4.3. Built-in CR Oscillation Characteristics for accuracy of built-in
CR.
Document Number: 002-05637 Rev. *C
Page 7 of 118
CY9A140NB Series
2. Packages
CY9AF141LB
CY9AF142LB
CY9AF144LB
CY9AF141MB
CY9AF142MB
CY9AF144MB
CY9AF141NB
CY9AF142NB
CY9AF144NB
LQFP: LQD064 (0.5 mm pitch)
-
-
LQFP: LQG064 (0.65 mm pitch)
-
-
QFN:
-
-
LQFP: LQH080 (0.5 mm pitch)
-
-
LQFP: LQJ080 (0.65 mm pitch)
-
-
BGA:
Product name
Package
VNC064 (0.5 mm pitch)
-
-
LQFP: LQI100 (0.5 mm pitch)
-
-
QFP:
PQH100 (0.65 mm pitch)
-
-
BGA:
LBC112 (0.8 mm pitch)
-
-
FDG096 (0.5 mm pitch)
: Supported
Note:
−
See “14. Package Dimensions” for detailed information on each package.
Document Number: 002-05637 Rev. *C
Page 8 of 118
CY9A140NB Series
3. Pin Assignment
LQI100
VSS
P81
P80
VCC
P60/SIN5_0/TIOA2_2/INT15_1/WKUP3/CEC1/MRDY_1
P61/SOT5_0/TIOB2_2
P62/SCK5_0/ADTG_3/MOEX_1
P63/INT03_0/MWEX_1
P0F/NMIX/CROUT_1/RTCCO_0/SUBOUT_0/WKUP0
P0E/CTS4_0/TIOB3_2/MDQM1_1
P0D/RTS4_0/TIOA3_2/MDQM0_1
P0C/SCK4_0/TIOA6_1/MALE_1
P0B/SOT4_0/TIOB6_1/MCSX0_1
P0A/SIN4_0/INT00_2/MCSX1_1
P09/TRACECLK/TIOB0_2/RTS4_2/MCSX2_1
P08/AN23/TRACED3/TIOA0_2/CTS4_2/MCSX3_1
P07/AN22/TRACED2/ADTG_0/SCK4_2/MCLKOUT_1
P06/AN21/TRACED1/TIOB5_2/SOT4_2/INT01_1/MCSX4_1
P05/AN20/TRACED0/TIOA5_2/SIN4_2/INT00_1/MCSX5_1
P04/TDO/SWO
P03/TMS/SWDIO
P02/TDI/MCSX6_1
P01/TCK/SWCLK
P00/TRSTX/MCSX7_1
VCC
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
(TOP VIEW)
VCC
1
75
VSS
P50/INT00_0/SIN3_1/MADATA00_1
2
74
P20/AN19/INT05_0/CROUT_0/MAD24_1
P51/INT01_0/SOT3_1/MADATA01_1
3
73
P21/AN18/SIN0_0/INT06_1/WKUP2
P52/INT02_0/SCK3_1/MADATA02_1
4
72
P22/AN17/SOT0_0/TIOB7_1
P53/SIN6_0/TIOA1_2/INT07_2/MADATA03_1
5
71
P23/AN16/SCK0_0/TIOA7_1
P54/SOT6_0/TIOB1_2/MADATA04_1
6
70
P1F/AN15/ADTG_5/MAD23_1
P55/SCK6_0/ADTG_1/MADATA05_1
7
69
P1E/AN14/RTS4_1/MAD22_1
P56/INT08_2/MADATA06_1
8
68
P1D/AN13/CTS4_1/MAD21_1
P30/TIOB0_1/INT03_2/MADATA07_1
9
67
P1C/AN12/SCK4_1/MAD20_1
P31/TIOB1_1/SCK6_1/INT04_2/MADATA08_1
10
66
P1B/AN11/SOT4_1/MAD19_1
P32/TIOB2_1/SOT6_1/INT05_2/MADATA09_1
11
65
P1A/AN10/SIN4_1/INT05_1/MAD18_1
P33/INT04_0/TIOB3_1/SIN6_1/ADTG_6/MADATA10_1
12
64
P19/AN09/SCK2_2/MAD17_1
P34/TIOB4_1/MADATA11_1
13
63
P18/AN08/SOT2_2/MAD16_1
P35/TIOB5_1/INT08_1/MADATA12_1
14
62
AVSS
P36/SIN5_2/INT09_1/MADATA13_1
15
61
AVRH
P37/SOT5_2/INT10_1/MADATA14_1
16
60
AVCC
P38/SCK5_2/INT11_1/MADATA15_1
17
59
P17/AN07/SIN2_2/INT04_1/MAD15_1
P39/ADTG_2
18
58
P16/AN06/SCK0_1/MAD14_1
P3A/TIOA0_1/RTCCO_2/SUBOUT_2
19
57
P15/AN05/SOT0_1/MAD13_1
P3B/TIOA1_1
20
56
P14/AN04/SIN0_1/INT03_1/MAD12_1
P3C/TIOA2_1
21
55
P13/AN03/SCK1_1/RTCCO_1/SUBOUT_1/MAD11_1
P3D/TIOA3_1
22
54
P12/AN02/SOT1_1/MAD10_1
P3E/TIOA4_1
23
53
P11/AN01/SIN1_1/INT02_1/WKUP1/MAD09_1
P3F/TIOA5_1
24
52
P10/AN00
VSS
25
51
VCC
46
47
48
49
50
MD0
PE2/X0
PE3/X1
VSS
39
P48/INT14_1/SIN3_2/MAD02_1
PE0/MD1
38
INITX
45
37
P47/X1A
P4E/TIOB5_0/INT06_2/SIN7_1/MAD08_1
36
P46/X0A
44
35
VCC
P4D/TIOB4_0/SOT7_1/MAD07_1
34
VSS
43
33
C
P4C/TIOB3_0/SCK7_1/CEC0/MAD06_1
32
P45/TIOA5_0/MAD01_1
42
31
P44/TIOA4_0/MAD00_1
41
30
P43/TIOA3_0/ADTG_7
P4B/TIOB2_0/MAD05_1
29
P42/TIOA2_0
40
28
P41/TIOA1_0/INT13_1
P49/TIOB0_0/SOT3_2/MAD03_1
27
P4A/TIOB1_0/SCK3_2/MAD04_1
26
VCC
P40/TIOA0_0/INT12_1
LQFP - 100
Note:
−
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these
pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register
(EPFR) to select the pin.
Document Number: 002-05637 Rev. *C
Page 9 of 118
CY9A140NB Series
PQH100
P50/INT00_0/SIN3_1/MADATA00_1
VCC
VSS
P81
P80
VCC
P60/SIN5_0/TIOA2_2/INT15_1/WKUP3/CEC1/MRDY_1
P61/SOT5_0/TIOB2_2
P62/SCK5_0/ADTG_3/MOEX_1
P63/INT03_0/MWEX_1
P0F/NMIX/CROUT_1/RTCCO_0/SUBOUT_0/WKUP0
P0E/CTS4_0/TIOB3_2/MDQM1_1
P0D/RTS4_0/TIOA3_2/MDQM0_1
P0C/SCK4_0/TIOA6_1/MALE_1
P0B/SOT4_0/TIOB6_1/MCSX0_1
P0A/SIN4_0/INT00_2/MCSX1_1
P09/TRACECLK/TIOB0_2/RTS4_2/MCSX2_1
P08/AN23/TRACED3/TIOA0_2/CTS4_2/MCSX3_1
P07/AN22/TRACED2/ADTG_0/SCK4_2/MCLKOUT_1
P06/AN21/TRACED1/TIOB5_2/SOT4_2/INT01_1/MCSX4_1
P05/AN20/TRACED0/TIOA5_2/SIN4_2/INT00_1/MCSX5_1
P04/TDO/SWO
P03/TMS/SWDIO
P02/TDI/MCSX6_1
P01/TCK/SWCLK
P00/TRSTX/MCSX7_1
VCC
VSS
P20/AN19/INT05_0/CROUT_0/MAD24_1
P21/AN18/SIN0_0/INT06_1/WKUP2
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
(TOP VIEW)
P51/INT01_0/SOT3_1/MADATA01_1
81
50
P22/AN17/SOT0_0/TIOB7_1
P52/INT02_0/SCK3_1/MADATA02_1
82
49
P23/AN16/SCK0_0/TIOA7_1
P53/SIN6_0/TIOA1_2/INT07_2/MADATA03_1
83
48
P1F/AN15/ADTG_5/MAD23_1
P54/SOT6_0/TIOB1_2/MADATA04_1
84
47
P1E/AN14/RTS4_1/MAD22_1
P55/SCK6_0/ADTG_1/MADATA05_1
85
46
P1D/AN13/CTS4_1/MAD21_1
P56/INT08_2/MADATA06_1
86
45
P1C/AN12/SCK4_1/MAD20_1
P30/TIOB0_1/INT03_2/MADATA07_1
87
44
P1B/AN11/SOT4_1/MAD19_1
P31/TIOB1_1/SCK6_1/INT04_2/MADATA08_1
88
43
P1A/AN10/SIN4_1/INT05_1/MAD18_1
P32/TIOB2_1/SOT6_1/INT05_2/MADATA09_1
89
42
P19/AN09/SCK2_2/MAD17_1
P33/INT04_0/TIOB3_1/SIN6_1/ADTG_6/MADATA10_1
90
41
P18/AN08/SOT2_2/MAD16_1
P34/TIOB4_1/MADATA11_1
91
40
AVSS
P35/TIOB5_1/INT08_1/MADATA12_1
92
39
AVRH
QFP - 100
18
19
20
21
22
23
24
25
26
27
28
29
30
P49/TIOB0_0/SOT3_2/MAD03_1
P4A/TIOB1_0/SCK3_2/MAD04_1
P4B/TIOB2_0/MAD05_1
P4C/TIOB3_0/SCK7_1/CEC0/MAD06_1
P4D/TIOB4_0/SOT7_1/MAD07_1
P4E/TIOB5_0/INT06_2/SIN7_1/MAD08_1
PE0/MD1
MD0
PE2/X0
PE3/X1
VSS
VCC
P10/AN00
15
P47/X1A
17
14
16
13
P46/X0A
INITX
12
VSS
VCC
P48/INT14_1/SIN3_2/MAD02_1
11
C
P11/AN01/SIN1_1/INT02_1/WKUP1/MAD09_1
9
31
10
100
P45/TIOA5_0/MAD01_1
P12/AN02/SOT1_1/MAD10_1
P3D/TIOA3_1
P44/TIOA4_0/MAD00_1
32
8
99
P43/TIOA3_0/ADTG_7
P13/AN03/SCK1_1/RTCCO_1/SUBOUT_1/MAD11_1
P3C/TIOA2_1
7
P14/AN04/SIN0_1/INT03_1/MAD12_1
33
6
34
98
P42/TIOA2_0
97
P3B/TIOA1_1
5
P15/AN05/SOT0_1/MAD13_1
P3A/TIOA0_1/RTCCO_2/SUBOUT_2
P41/TIOA1_0/INT13_1
35
P40/TIOA0_0/INT12_1
96
4
P16/AN06/SCK0_1/MAD14_1
P39/ADTG_2
VCC
36
3
95
2
P17/AN07/SIN2_2/INT04_1/MAD15_1
P38/SCK5_2/INT11_1/MADATA15_1
1
AVCC
37
VSS
38
94
P3F/TIOA5_1
93
P3E/TIOA4_1
P36/SIN5_2/INT09_1/MADATA13_1
P37/SOT5_2/INT10_1/MADATA14_1
Note:
−
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these
pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register
(EPFR) to select the pin.
Document Number: 002-05637 Rev. *C
Page 10 of 118
CY9A140NB Series
LQH080/ LQJ080
VSS
P81
P80
VCC
P60/SIN5_0/TIOA2_2/INT15_1/WKUP3/CEC1/MRDY_1
P61/SOT5_0/TIOB2_2
P62/SCK5_0/ADTG_3/MOEX_1
P63/INT03_0/MWEX_1
P0F/NMIX/CROUT_1/RTCCO_0/SUBOUT_0/WKUP0
P0E/CTS4_0/TIOB3_2/MDQM1_1
P0D/RTS4_0/TIOA3_2/MDQM0_1
P0C/SCK4_0/TIOA6_1/MALE_1
P0B/SOT4_0/TIOB6_1/MCSX0_1
P0A/SIN4_0/INT00_2/MCSX1_1
P07/AN22/ADTG_0/MCLKOUT_1
P04/TDO/SWO
P03/TMS/SWDIO
P02/TDI/MCSX6_1
P01/TCK/SWCLK
P00/TRSTX/MCSX7_1
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
(TOP VIEW)
VCC
1
60
P20/AN19/INT05_0/CROUT_0/MAD24_1
P50/INT00_0/SIN3_1/MADATA00_1
2
59
P21/AN18/SIN0_0/INT06_1/WKUP2
P51/INT01_0/SOT3_1/MADATA01_1
3
58
P22/AN17/SOT0_0/TIOB7_1
P52/INT02_0/SCK3_1/MADATA02_1
4
57
P23/AN16/SCK0_0/TIOA7_1
P53/SIN6_0/TIOA1_2/INT07_2/MADATA03_1
5
56
P1B/AN11/SOT4_1/MAD19_1
P54/SOT6_0/TIOB1_2/MADATA04_1
6
55
P1A/AN10/SIN4_1/INT05_1/MAD18_1
P55/SCK6_0/ADTG_1/MADATA05_1
7
54
P19/AN09/SCK2_2/MAD17_1
P56/INT08_2/MADATA06_1
8
53
P18/AN08/SOT2_2/MAD16_1
P30/TIOB0_1/INT03_2/MADATA07_1
9
52
AVSS
P31/TIOB1_1/SCK6_1/INT04_2/MADATA08_1
10
51
AVRH
P32/TIOB2_1/SOT6_1/INT05_2/MADATA09_1
11
50
AVCC
P33/INT04_0/TIOB3_1/SIN6_1/ADTG_6/MADATA10_1
12
49
P17/AN07/SIN2_2/INT04_1/MAD15_1
P39/ADTG_2
13
48
P16/AN06/SCK0_1/MAD14_1
P3A/TIOA0_1/RTCCO_2/SUBOUT_2
14
47
P15/AN05/SOT0_1/MAD13_1
P3B/TIOA1_1
15
46
P14/AN04/SIN0_1/INT03_1/MAD12_1
P3C/TIOA2_1
16
45
P13/AN03/SCK1_1/RTCCO_1/SUBOUT_1/MAD11_1
P3D/TIOA3_1
17
44
P12/AN02/SOT1_1/MAD10_1
P3E/TIOA4_1
18
43
P11/AN01/SIN1_1/INT02_1/WKUP1/MAD09_1
P3F/TIOA5_1
19
42
P10/AN00
VSS
20
41
VCC
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
P44/TIOA4_0/MAD00_1
P45/TIOA5_0/MAD01_1
C
VSS
VCC
P46/X0A
P47/X1A
INITX
P48/INT14_1/SIN3_2/MAD02_1
P49/TIOB0_0/SOT3_2/MAD03_1
P4A/TIOB1_0/SCK3_2/MAD04_1
P4B/TIOB2_0/MAD05_1
P4C/TIOB3_0/SCK7_1/CEC0/MAD06_1
P4D/TIOB4_0/SOT7_1/MAD07_1
P4E/TIOB5_0/INT06_2/SIN7_1/MAD08_1
PE0/MD1
MD0
PE2/X0
PE3/X1
VSS
LQFP - 80
Note:
−
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these
pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register
(EPFR) to select the pin.
Document Number: 002-05637 Rev. *C
Page 11 of 118
CY9A140NB Series
LQD064/ LQG064
P03/TMS/SWDIO
P02/TDI
P01/TCK/SWCLK
P00/TRSTX
52
51
50
49
P0A/SIN4_0/INT00_2
P04/TDO/SWO
54
53
P0C/SCK4_0/TIOA6_1
P0B/SOT4_0/TIOB6_1
56
55
P62/SCK5_0/ADTG_3
P0F/NMIX/CROUT_1/RTCCO_0/SUBOUT_0/WKUP0
58
57
P60/SIN5_0/TIOA2_2/INT15_1/WKUP3/CEC1
P61/SOT5_0/TIOB2_2
60
59
P80
VCC
62
61
VSS
P81
64
63
(TOP VIEW)
VCC
1
48
P21/AN18/SIN0_0/INT06_1/WKUP2
P50/INT00_0/SIN3_1
2
47
P22/AN17/SOT0_0/TIOB7_1
P51/INT01_0/SOT3_1
3
46
P23/AN16/SCK0_0/TIOA7_1
P52/INT02_0/SCK3_1
4
45
P19/AN09/SCK2_2
P30/TIOB0_1/INT03_2
5
44
P18/AN08/SOT2_2
P31/TIOB1_1/SCK6_1/INT04_2
6
43
AVSS
P32/TIOB2_1/SOT6_1/INT05_2
7
42
AVRH
P33/INT04_0/TIOB3_1/SIN6_1/ADTG_6
8
41
AVCC
P39/ADTG_2
9
40
P17/AN07/SIN2_2/INT04_1
P3A/TIOA0_1/RTCCO_2/SUBOUT_2
10
39
P15/AN05
P3B/TIOA1_1
11
38
P14/AN04/INT03_1
P3C/TIOA2_1
12
37
P13/AN03/SCK1_1/RTCCO_1/SUBOUT_1
P3D/TIOA3_1
13
36
P12/AN02/SOT1_1
P3E/TIOA4_1
14
35
P11/AN01/SIN1_1/INT02_1/WKUP1
P3F/TIOA5_1
15
34
P10/AN00
VSS
16
33
VCC
29
31
32
PE3/X1
VSS
PE0/MD1
30
P4E/TIOB5_0/INT06_2/SIN7_1
MD0
27
28
P4D/TIOB4_0/SOT7_1
PE2/X0
25
26
P4C/TIOB3_0/SCK7_1/CEC0
23
24
P4A/TIOB1_0
P4B/TIOB2_0
21
22
INITX
19
20
P46/X0A
P47/X1A
P49/TIOB0_0
17
18
C
VCC
LQFP - 64
Note:
−
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these
pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register
(EPFR) to select the pin.
Document Number: 002-05637 Rev. *C
Page 12 of 118
CY9A140NB Series
VNC064
VSS
P81
P80
VCC
P60/SIN5_0/TIOA2_2/INT15_1/WKUP3/CEC1
P61/SOT5_0/TIOB2_2
P62/SCK5_0/ADTG_3
P0F/NMIX/CROUT_1/RTCCO_0/SUBOUT_0/WKUP0
P0C/SCK4_0/TIOA6_1
P0B/SOT4_0/TIOB6_1
P0A/SIN4_0/INT00_2
P04/TDO/SWO
P03/TMS/SWDIO
P02/TDI
P01/TCK/SWCLK
P00/TRSTX
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
(TOP VIEW)
VCC
1
48
P21/AN18/SIN0_0/INT06_1/WKUP2
P50/INT00_0/SIN3_1
2
47
P22/AN17/SOT0_0/TIOB7_1
P51/INT01_0/SOT3_1
3
46
P23/AN16/SCK0_0/TIOA7_1
P52/INT02_0/SCK3_1
4
45
P19/AN09/SCK2_2
P30/TIOB0_1/INT03_2
5
44
P18/AN08/SOT2_2
P31/TIOB1_1/SCK6_1/INT04_2
6
43
AVSS
P32/TIOB2_1/SOT6_1/INT05_2
7
42
AVRH
P33/INT04_0/TIOB3_1/SIN6_1/ADTG_6
8
41
AVCC
P39/ADTG_2
9
40
P17/AN07/SIN2_2/INT04_1
P3A/TIOA0_1/RTCCO_2/SUBOUT_2
10
39
P15/AN05
P3B/TIOA1_1
11
38
P14/AN04/INT03_1
P3C/TIOA2_1
12
37
P13/AN03/SCK1_1/RTCCO_1/SUBOUT_1
P3D/TIOA3_1
13
36
P12/AN02/SOT1_1
P3E/TIOA4_1
14
35
P11/AN01/SIN1_1/INT02_1/WKUP1
P3F/TIOA5_1
15
34
P10/AN00
VSS
16
33
VCC
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
C
VCC
P46/X0A
P47/X1A
INITX
P49/TIOB0_0
P4A/TIOB1_0
P4B/TIOB2_0
P4C/TIOB3_0/SCK7_1/CEC0
P4D/TIOB4_0/SOT7_1
P4E/TIOB5_0/INT06_2/SIN7_1
PE0/MD1
MD0
PE2/X0
PE3/X1
VSS
QFN - 64
Note:
−
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these
pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register
(EPFR) to select the pin.
Document Number: 002-05637 Rev. *C
Page 13 of 118
CY9A140NB Series
LBC112
(TOP VIEW)
1
2
3
4
5
6
7
8
9
10
11
A
VSS
P81
P80
VCC
P0E
P0B
AN22
TMS/
SWDIO
TRSTX
VCC
VSS
B
VCC
VSS
P52
P61
P0F
P0C
AN23
TDO/
SWO
TCK/
SWCLK
VSS
TDI
C
P50
P51
VSS
P60
P62
P0D
P09
AN20
VSS
AN19
AN18
D
P53
P54
P55
VSS
P56
P63
P0A
VSS
AN21
AN16
AN15
E
P30
P31
P32
P33
Index
AN17
AN14
AN12
AN11
F
P34
P35
P36
P39
AN13
AN10
AN09
AVRH
G
P37
P38
P3A
P3D
AN08
AN07
AN06
AVSS
H
P3B
P3C
P3E
VSS
P44
P4C
AN05
VSS
AN04
AN03
AVCC
J
VCC
P3F
VSS
P40
P43
P49
P4D
AN02
VSS
AN01
AN00
K
VCC
VSS
X1A
INITX
P42
P48
P4B
P4E
MD1
VSS
VCC
L
VSS
C
X0A
VSS
P41
P45
P4A
MD0
X0
X1
VSS
PFBGA - 112
Note:
−
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these
pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register
(EPFR) to select the pin.
Document Number: 002-05637 Rev. *C
Page 14 of 118
CY9A140NB Series
FDG096
(TOP VIEW)
1
2
3
4
5
6
7
8
9
10
11
A
VSS
P81
P80
VCC
VSS
P0F
VSS
AN22
TMS/
SWDIO
TRSTX
VSS
B
VCC
VSS
P52
P61
P63
P0D
P0C
TDO/
SWO
TCK/
SWCLK
VSS
TDI
C
P50
P51
VSS
P60
P62
P0E
P0B
P0A
VSS
AN19
AN18
D
P53
P54
P55
Index
AN17
AN16
VSS
E
P56
P30
P31
AN11
AN10
AN09
F
VSS
VSS
VSS
AN08
AN07
AVRH
G
P32
P33
P39
AN06
AN05
AVSS
H
P3A
P3B
P3C
AN04
AN03
AVCC
J
P3D
P3E
VSS
P3F
P48
P4A
P4D
AN02
VSS
AN01
AN00
K
VCC
VSS
X1A
INITX
P45
P49
P4C
P4E
MD1
VSS
VCC
L
VSS
C
X0A
VSS
P44
VSS
P4B
MD0
X0
X1
VSS
PFBGA - 96
Note:
−
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these
pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register
(EPFR) to select the pin.
Document Number: 002-05637 Rev. *C
Page 15 of 118
CY9A140NB Series
4. List of Pin Functions
List of pin numbers
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins,
there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR) to
select the pin.
Pin No
LQFP-100
1
QFP-100
79
BGA-112
B1
LQFP-80
1
B1
Pin Name
LQFP-64
QFN-64
BGA-96
1
VCC
I/O Circuit
Type
Pin State
Type
-
P50
2
80
C1
2
C1
2
INT00_0
SIN3_1
-
E
L
E
L
E
L
E
L
E
K
E
K
E
L
E
L
MADATA00_1
P51
3
81
C2
3
C2
3
-
INT01_0
SOT3_1
(SDA3_1)
MADATA01_1
P52
4
82
B3
4
B3
4
-
INT02_0
SCK3_1
(SCL3_1)
MADATA02_1
P53
SIN6_0
5
83
D1
5
D1
-
TIOA1_2
INT07_2
MADATA03_1
P54
6
84
D2
6
D2
-
SOT6_0
(SDA6_0)
TIOB1_2
MADATA04_1
P55
7
85
D3
7
D3
-
SCK6_0
(SCL6_0)
ADTG_1
MADATA05_1
P56
8
86
D5
8
E1
-
INT08_2
MADATA06_1
P30
9
87
E1
9
E2
5
INT03_2
-
Document Number: 002-05637 Rev. *C
TIOB0_1
MADATA07_1
Page 16 of 118
CY9A140NB Series
Pin No
LQFP-100
QFP-100
BGA-112
LQFP-80
Pin Name
LQFP-64
QFN-64
BGA-96
I/O Circuit
Type
Pin State
Type
P31
TIOB1_1
10
88
E2
10
E3
6
SCK6_1
(SCL6_1)
E
L
E
L
E
L
E
K
E
L
E
L
INT04_2
-
MADATA08_1
P32
TIOB2_1
11
89
E3
11
G1
7
SOT6_1
(SDA6_1)
INT05_2
-
MADATA09_1
P33
INT04_0
12
90
E4
12
G2
8
TIOB3_1
SIN6_1
ADTG_6
-
MADATA10_1
P34
13
91
F1
-
-
-
TIOB4_1
MADATA11_1
P35
14
92
F2
-
-
-
TIOB5_1
INT08_1
MADATA12_1
P36
SIN5_2
15
93
F3
-
-
-
-
-
-
-
F1
-
VSS
-
-
-
-
-
F2
-
VSS
-
-
-
-
-
F3
-
VSS
-
INT09_1
MADATA13_1
P37
16
94
G1
-
-
-
SOT5_2
(SDA5_2)
E
L
E
L
E
K
INT10_1
MADATA14_1
P38
17
95
G2
-
-
-
SCK5_2
(SCL5_2)
INT11_1
MADATA15_1
18
96
F4
Document Number: 002-05637 Rev. *C
13
G3
9
P39
ADTG_2
Page 17 of 118
CY9A140NB Series
Pin No
LQFP-100
QFP-100
BGA-112
LQFP-80
Pin Name
LQFP-64
QFN-64
BGA-96
I/O Circuit
Type
Pin State
Type
P3A
19
97
G3
14
H1
10
TIOA0_1
RTCCO_2
E
K
E
K
E
K
E
K
SUBOUT_2
20
98
H1
15
H2
11
21
99
H2
16
H3
12
22
100
G4
17
J1
13
-
-
B2
-
B2
-
P3B
TIOA1_1
P3C
TIOA2_1
P3D
TIOA3_1
VSS
P3E
-
23
1
H3
18
J2
14
24
2
J2
19
J4
15
25
3
L1
20
L1
16
VSS
-
26
4
J1
-
-
-
VCC
-
TIOA4_1
P3F
TIOA5_1
E
K
E
K
P40
27
5
J4
-
-
-
TIOA0_0
E
L
E
L
E
K
E
K
E
K
E
K
INT12_1
P41
28
6
L5
-
-
-
TIOA1_0
INT13_1
29
7
K5
-
-
-
30
8
J5
-
-
-
P42
TIOA2_0
P43
TIOA3_0
31
9
H5
21
L5
-
32
10
L6
22
K5
-
-
-
K2
-
K2
-
ADTG_7
P44
TIOA4_0
MAD00_1
P45
TIOA5_0
MAD01_1
VSS
-
-
J3
-
J3
-
VSS
-
-
-
H4
-
-
-
VSS
-
-
-
-
-
L6
-
VSS
-
33
11
L2
23
L2
17
C
-
34
12
L4
24
L4
-
VSS
-
35
13
K1
25
K1
18
VCC
-
36
14
L3
26
L3
19
37
15
K3
27
K3
20
Document Number: 002-05637 Rev. *C
P46
X0A
P47
X1A
-
D
F
D
G
Page 18 of 118
CY9A140NB Series
Pin No
LQFP-100
38
QFP-100
16
BGA-112
K4
LQFP-80
28
K4
21
I/O Circuit
Type
Pin Name
LQFP-64
QFN-64
BGA-96
INITX
Pin State
Type
B
C
E
L
E
K
E
K
E
K
I
S
I
K
I
L
C
E
G
D
A
A
A
B
P48
39
17
K6
29
J5
-
INT14_1
SIN3_2
MAD02_1
22
40
18
J6
30
K6
-
P49
TIOB0_0
SOT3_2
(SDA3_2)
MAD03_1
23
41
19
L7
31
J6
-
P4A
TIOB1_0
SCK3_2
(SCL3_2)
MAD04_1
42
20
K7
32
L7
24
-
P4B
TIOB2_0
MAD05_1
P4C
TIOB3_0
43
21
H6
33
K7
25
SCK7_1
(SCL7_1)
CEC0
-
MAD06_1
P4D
44
22
J7
34
J7
26
-
TIOB4_0
SOT7_1
(SDA7_1)
MAD07_1
P4E
45
23
K8
35
K8
27
TIOB5_0
INT06_2
SIN7_1
46
24
K9
36
K9
28
47
25
L8
37
L8
29
MAD08_1
MD1
PE0
MD0
X0
48
26
L9
38
L9
30
49
27
L10
39
L10
31
50
28
L11
40
L11
32
VSS
-
51
29
K11
41
K11
33
VCC
-
52
30
J11
Document Number: 002-05637 Rev. *C
42
J11
34
PE2
X1
PE3
P10
AN00
F
M
Page 19 of 118
CY9A140NB Series
Pin No
LQFP-100
QFP-100
BGA-112
LQFP-80
I/O Circuit
Type
Pin Name
LQFP-64
QFN-64
BGA-96
Pin State
Type
P11
AN01
53
31
J10
43
J10
35
SIN1_1
INT02_1
F
R
F
M
WKUP1
-
MAD09_1
P12
36
AN02
54
32
J8
44
J8
-
MAD10_1
-
-
K10
-
K10
-
VSS
-
-
-
J9
-
J9
-
VSS
-
SOT1_1
(SDA1_1)
P13
AN03
55
33
H10
45
H10
37
SCK1_1
(SCL1_1)
F
M
F
N
F
M
F
M
F
N
RTCCO_1
SUBOUT_1
-
MAD11_1
P14
38
56
34
H9
46
H9
INT03_1
39
57
35
H7
47
AN04
G10
-
SIN0_1
MAD12_1
P15
AN05
SOT0_1
(SDA0_1)
MAD13_1
P16
AN06
58
36
G10
48
G9
-
SCK0_1
(SCL0_1)
MAD14_1
P17
59
37
G9
49
F10
40
AN07
SIN2_2
INT04_1
-
MAD15_1
60
38
H11
50
H11
41
AVCC
-
61
39
F11
51
F11
42
AVRH
-
62
40
G11
52
G11
43
AVSS
-
Document Number: 002-05637 Rev. *C
Page 20 of 118
CY9A140NB Series
Pin No
LQFP-100
QFP-100
BGA-112
LQFP-80
I/O Circuit
Type
Pin Name
LQFP-64
QFN-64
BGA-96
Pin State
Type
P18
63
41
G8
53
F9
44
-
AN08
SOT2_2
(SDA2_2)
F
M
F
M
MAD16_1
P19
64
42
F10
54
E11
-
-
H8
-
-
45
AN09
SCK2_2
(SCL2_2)
-
MAD17_1
-
VSS
-
P1A
AN10
65
43
F9
55
E10
-
SIN4_1
F
N
F
M
F
M
F
M
F
M
F
M
INT05_1
MAD18_1
P1B
AN11
66
44
E11
56
E9
-
SOT4_1
(SDA4_1)
MAD19_1
P1C
AN12
67
45
E10
-
-
-
SCK4_1
(SCL4_1)
MAD20_1
P1D
68
46
F8
-
-
-
AN13
CTS4_1
MAD21_1
P1E
69
47
E9
-
-
-
AN14
RTS4_1
MAD22_1
P1F
70
48
D11
-
-
-
AN15
ADTG_5
MAD23_1
-
-
B10
-
B10
-
VSS
-
-
-
C9
-
C9
-
VSS
-
-
-
-
-
D11
-
VSS
-
Document Number: 002-05637 Rev. *C
Page 21 of 118
CY9A140NB Series
Pin No
LQFP-100
QFP-100
BGA-112
LQFP-80
I/O Circuit
Type
Pin Name
LQFP-64
QFN-64
BGA-96
Pin State
Type
P23
AN16
71
49
D10
57
D10
46
SCK0_0
(SCL0_0)
F
M
F
M
F
R
F
N
TIOA7_1
P22
AN17
72
50
E8
58
D9
47
SOT0_0
(SDA0_0)
TIOB7_1
P21
AN18
73
51
C11
59
C11
48
SIN0_0
INT06_1
WKUP2
P20
AN19
74
52
C10
60
C10
-
INT05_0
CROUT_0
MAD24_1
75
53
A11
-
A11
-
VSS
-
76
54
A10
-
-
-
VCC
-
77
55
A9
61
A10
49
-
P00
TRSTX
E
J
E
J
E
J
E
J
E
J
F
Q
MCSX7_1
P01
78
56
B9
62
B9
50
TCK
SWCLK
79
57
B11
63
B11
51
-
P02
TDI
MCSX6_1
P03
80
58
A8
64
A9
52
TMS
SWDIO
P04
81
59
B8
65
B8
53
TDO
SWO
P05
AN20
TRACED0
82
60
C8
-
-
-
TIOA5_2
SIN4_2
INT00_1
MCSX5_1
Document Number: 002-05637 Rev. *C
Page 22 of 118
CY9A140NB Series
Pin No
LQFP-100
-
QFP-100
-
BGA-112
D8
LQFP-80
-
-
-
I/O Circuit
Type
Pin Name
LQFP-64
QFN-64
BGA-96
VSS
Pin State
Type
-
P06
AN21
TRACED1
83
61
D9
-
-
-
TIOB5_2
SOT4_2
(SDA4_2)
F
Q
F
P
INT01_1
MCSX4_1
P07
66
84
62
AN22
A8
A7
ADTG_0
-
MCLKOUT_1
TRACED2
-
-
-
-
-
-
A7
SCK4_2
(SCL4_2)
-
VSS
-
P08
AN23
85
63
B7
-
-
-
TRACED3
TIOA0_2
F
P
E
O
I
L
I
K
I
K
CTS4_2
MCSX3_1
P09
TRACECLK
86
64
C7
-
-
-
TIOB0_2
RTS4_2
MCSX2_1
P0A
87
65
D7
67
C8
54
SIN4_0
INT00_2
-
MCSX1_1
P0B
88
66
A6
68
C7
55
SOT4_0
(SDA4_0)
TIOB6_1
-
MCSX0_1
P0C
89
67
B6
69
B7
56
SCK4_0
(SCL4_0)
TIOA6_1
-
-
D4
Document Number: 002-05637 Rev. *C
-
-
-
MALE_1
-
VSS
-
Page 23 of 118
CY9A140NB Series
Pin No
LQFP-100
-
QFP-100
-
BGA-112
C3
LQFP-80
-
C3
-
I/O Circuit
Type
Pin Name
LQFP-64
QFN-64
BGA-96
VSS
Pin State
Type
-
P0D
90
68
C6
70
B6
-
RTS4_0
TIOA3_2
E
K
E
K
MDQM0_1
P0E
91
69
A5
71
C6
-
-
-
-
-
A5
-
CTS4_0
TIOB3_2
MDQM1_1
VSS
-
P0F
NMIX
92
70
B5
72
A6
57
CROUT_1
RTCCO_0
E
I
E
L
E
K
E
K
I
T
SUBOUT_0
WKUP0
P63
93
71
D6
73
B5
-
INT03_0
MWEX_1
P62
94
72
C5
74
C5
58
SCK5_0
(SCL5_0)
ADTG_3
-
MOEX_1
P61
95
73
B4
75
B4
59
SOT5_0
(SDA5_0)
TIOB2_2
P60
SIN5_0
96
74
C4
76
C4
60
TIOA2_2
INT15_1
WKUP3
CEC1
-
MRDY_1
97
75
A4
77
A4
61
VCC
-
98
76
A3
78
A3
62
P80
H
H
99
77
A2
79
A2
63
P81
H
H
100
78
A1
80
A1
64
VSS
-
Document Number: 002-05637 Rev. *C
Page 24 of 118
CY9A140NB Series
List of pin functions
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins,
there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR) to
select the pin.
Pin
Function
ADC
Pin No
Pin Name
ADTG_0
ADTG_1
ADTG_2
ADTG_3
ADTG_4
ADTG_5
ADTG_6
ADTG_7
ADTG_8
AN00
AN01
AN02
AN03
AN04
AN05
AN06
AN07
AN08
AN09
AN10
AN11
AN12
AN13
AN14
AN15
AN16
AN17
AN18
AN19
AN20
AN21
AN22
AN23
Function Description
A/D converter external trigger
input pin
A/D converter analog input pin.
ANxx describes ADC ch.xx.
Document Number: 002-05637 Rev. *C
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-64
84
7
18
94
70
12
30
52
53
54
55
56
57
58
59
63
64
65
66
67
68
69
70
71
72
73
74
82
83
84
85
62
85
96
72
48
90
8
30
31
32
33
34
35
36
37
41
42
43
44
45
46
47
48
49
50
51
52
60
61
62
63
A7
D3
F4
C5
D11
E4
J5
J11
J10
J8
H10
H9
H7
G10
G9
G8
F10
F9
E11
E10
F8
E9
D11
D10
E8
C11
C10
C8
D9
A7
B7
66
7
13
74
12
42
43
44
45
46
47
48
49
53
54
55
56
57
58
59
60
66
-
A8
D3
G3
C5
G2
J11
J10
J8
H10
H9
G10
G9
F10
F9
E11
E10
E9
D10
D9
C11
C10
A8
-
9
58
8
34
35
36
37
38
39
40
44
45
46
47
48
-
Page 25 of 118
CY9A140NB Series
Pin
Function
Base Timer
0
Base Timer
1
Base Timer
2
Base Timer
3
Base Timer
4
Base Timer
5
Base Timer
6
Base Timer
7
Pin No
Pin Name
TIOA0_0
TIOA0_1
TIOA0_2
TIOB0_0
TIOB0_1
TIOB0_2
TIOA1_0
TIOA1_1
TIOA1_2
TIOB1_0
TIOB1_1
TIOB1_2
TIOA2_0
TIOA2_1
TIOA2_2
TIOB2_0
TIOB2_1
TIOB2_2
TIOA3_0
TIOA3_1
TIOA3_2
TIOB3_0
TIOB3_1
TIOB3_2
TIOA4_0
TIOA4_1
TIOA4_2
TIOB4_0
TIOB4_1
TIOB4_2
TIOA5_0
TIOA5_1
TIOA5_2
TIOB5_0
TIOB5_1
TIOB5_2
Function Description
Base timer ch.0 TIOA pin
Base timer ch.0 TIOB pin
Base timer ch.1 TIOA pin
Base timer ch.1 TIOB pin
Base timer ch.2 TIOA pin
Base timer ch.2 TIOB pin
Base timer ch.3 TIOA pin
Base timer ch.3 TIOB pin
Base timer ch.4 TIOA pin
Base timer ch.4 TIOB pin
Base timer ch.5 TIOA pin
Base timer ch.5 TIOB pin
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-64
27
19
85
40
9
86
28
20
5
41
10
6
29
21
96
42
11
95
30
22
90
43
12
91
31
23
44
13
32
24
82
45
14
83
5
97
63
18
87
64
6
98
83
19
88
84
7
99
74
20
89
73
8
100
68
21
90
69
9
1
22
91
10
2
60
23
92
61
J4
G3
B7
J6
E1
C7
L5
H1
D1
L7
E2
D2
K5
H2
C4
K7
E3
B4
J5
G4
C6
H6
E4
A5
H5
H3
J7
F1
L6
J2
C8
K8
F2
D9
14
30
9
15
5
31
10
6
16
76
32
11
75
17
70
33
12
71
21
18
34
22
19
35
-
H1
K6
E2
H2
D1
J6
E3
D2
H3
C4
L7
G1
B4
J1
B6
K7
G2
C6
L5
J2
J7
K5
J4
K8
-
10
22
5
11
23
6
12
60
24
7
59
13
25
8
14
26
15
27
-
TIOA6_1
Base timer ch.6 TIOA pin
89
67
B6
69
B7
56
TIOB6_1
Base timer ch.6 TIOB pin
88
66
A6
68
C7
55
71
72
-
49
50
-
D10
E8
-
57
58
-
D10
D9
-
46
47
-
TIOA7_0
TIOA7_1
TIOA7_2
TIOB7_0
TIOB7_1
TIOB7_2
Base timer ch.7 TIOA pin
Base timer ch.7 TIOB pin
Document Number: 002-05637 Rev. *C
Page 26 of 118
CY9A140NB Series
Pin
Function
Debugger
Pin No
Pin Name
SWCLK
SWDIO
SWO
TCK
TDI
TDO
TMS
External
Bus
TRACECLK
TRACED0
TRACED1
TRACED2
TRACED3
TRSTX
MAD00_1
MAD01_1
MAD02_1
MAD03_1
MAD04_1
MAD05_1
MAD06_1
MAD07_1
MAD08_1
MAD09_1
MAD10_1
MAD11_1
MAD12_1
MAD13_1
MAD14_1
MAD15_1
MAD16_1
MAD17_1
MAD18_1
MAD19_1
MAD20_1
MAD21_1
MAD22_1
MAD23_1
MAD24_1
Function Description
Serial wire debug interface
clock input pin
Serial wire debug interface
data input / output pin
Serial wire viewer output pin
JTAG test clock input pin
JTAG test data input pin
JTAG debug data output pin
JTAG test mode state
input/output pin
Trace CLK output pin of ETM
Trace data output pins of ETM
JTAG test reset input pin
External bus interface address
bus
Document Number: 002-05637 Rev. *C
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-64
78
56
B9
62
B9
50
80
58
A8
64
A9
52
81
78
79
81
59
56
57
59
B8
B9
B11
B8
65
62
63
65
B8
B9
B11
B8
53
50
51
53
80
58
A8
64
A9
52
86
82
83
84
85
77
31
32
39
40
41
42
43
44
45
53
54
55
56
57
58
59
63
64
65
66
67
68
69
70
74
64
60
61
62
63
55
9
10
17
18
19
20
21
22
23
31
32
33
34
35
36
37
41
42
43
44
45
46
47
48
52
C7
C8
D9
A7
B7
A9
H5
L6
K6
J6
L7
K7
H6
J7
K8
J10
J8
H10
H9
H7
G10
G9
G8
F10
F9
E11
E10
F8
E9
D11
C10
61
21
22
29
30
31
32
33
34
35
43
44
45
46
47
48
49
53
54
55
56
60
A10
L5
K5
J5
K6
J6
L7
K7
J7
K8
J10
J8
H10
H9
G10
G9
F10
F9
E11
E10
E9
C10
49
-
Page 27 of 118
CY9A140NB Series
Pin
Function
External
Bus
Pin No
Pin Name
MCSX0_1
MCSX1_1
MCSX2_1
MCSX3_1
MCSX4_1
MCSX5_1
MCSX6_1
MCSX7_1
MDQM0_1
MDQM1_1
MOEX_1
MWEX_1
MADATA00
_1
MADATA01
_1
MADATA02
_1
MADATA03
_1
MADATA04
_1
MADATA05
_1
MADATA06
_1
MADATA07
_1
MADATA08
_1
MADATA09
_1
MADATA10
_1
MADATA11_
1
MADATA12
_1
MADATA13
_1
MADATA14
_1
MADATA15
_1
MALE_1
MRDY_1
MCLKOUT
_1
Function Description
External bus interface chip
select output pin
External bus interface byte
mask signal output pin
External bus interface read
enable signal for SRAM
External bus interface write
enable signal for SRAM
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-64
88
87
86
85
83
82
79
77
90
91
66
65
64
63
61
60
57
55
68
69
A6
D7
C7
B7
D9
C8
B11
A9
C6
A5
68
67
63
61
70
71
C7
C8
B11
A10
B6
C6
-
94
72
C5
74
C5
-
93
71
D6
73
B5
-
2
80
C1
2
C1
-
3
81
C2
3
C2
-
4
82
B3
4
B3
-
5
83
D1
5
D1
-
6
84
D2
6
D2
-
7
85
D3
7
D3
-
8
86
D5
8
E1
-
9
87
E1
9
E2
-
10
88
E2
10
E3
-
11
89
E3
11
G1
-
12
90
E4
12
G2
-
13
91
F1
-
-
-
14
92
F2
-
-
-
15
93
F3
-
-
-
16
94
G1
-
-
-
17
95
G2
-
-
-
89
67
B6
69
B7
-
96
74
C4
76
C4
-
84
62
A7
66
A8
-
External bus interface data bus
Address Latch enable signal
for multiplex
External RDY input signal
External bus clock output pin
Document Number: 002-05637 Rev. *C
Page 28 of 118
CY9A140NB Series
Pin
Function
External
Interrupt
Pin No
Pin Name
INT00_0
INT00_1
INT00_2
INT01_0
INT01_1
INT02_0
INT02_1
INT03_0
INT03_1
INT03_2
INT04_0
INT04_1
INT04_2
INT05_0
INT05_1
INT05_2
INT06_1
INT06_2
INT07_2
INT08_1
INT08_2
INT09_1
INT10_1
INT11_1
INT12_1
INT13_1
INT14_1
INT15_1
NMIX
Function Description
External interrupt request 00
input pin
External interrupt request 01
input pin
External interrupt request 02
input pin
External interrupt request 03
input pin
External interrupt request 04
input pin
External interrupt request 05
input pin
External interrupt request 06
input pin
External interrupt request 07
input pin
External interrupt request 08
input pin
External interrupt request 09
input pin
External interrupt request 10
input pin
External interrupt request 11
input pin
External interrupt request 12
input pin
External interrupt request 13
input pin
External interrupt request 14
input pin
External interrupt request 15
input pin
Non-Maskable Interrupt input
pin
Document Number: 002-05637 Rev. *C
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-64
2
82
87
3
83
4
53
93
56
9
12
59
10
74
65
11
73
45
80
60
65
81
61
82
31
71
34
87
90
37
88
52
43
89
51
23
C1
C8
D7
C2
D9
B3
J10
D6
H9
E1
E4
G9
E2
C10
F9
E3
C11
K8
2
67
3
4
43
73
46
9
12
49
10
60
55
11
59
35
C1
C8
C2
B3
J10
B5
H9
E2
G2
F10
E3
C10
E10
G1
C11
K8
2
54
3
4
35
38
5
8
40
6
7
48
27
5
83
D1
5
D1
-
14
8
92
86
F2
D5
8
E1
-
15
93
F3
-
-
-
16
94
G1
-
-
-
17
95
G2
-
-
-
27
5
J4
-
-
-
28
6
L5
-
-
-
39
17
K6
29
J5
-
96
74
C4
76
C4
60
92
70
B5
72
A6
57
Page 29 of 118
CY9A140NB Series
Pin
Function
GPIO
Pin No
Pin Name
P00
P01
P02
P03
P04
P05
P06
P07
P08
P09
P0A
P0B
P0C
P0D
P0E
P0F
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P1A
P1B
P1C
P1D
P1E
P1F
P20
P21
P22
P23
Function Description
General-purpose I/O port 0
General-purpose I/O port 1
General-purpose I/O port 2
Document Number: 002-05637 Rev. *C
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-64
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
52
53
54
55
56
57
58
59
63
64
65
66
67
68
69
70
74
73
72
71
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
30
31
32
33
34
35
36
37
41
42
43
44
45
46
47
48
52
51
50
49
A9
B9
B11
A8
B8
C8
D9
A7
B7
C7
D7
A6
B6
C6
A5
B5
J11
J10
J8
H10
H9
H7
G10
G9
G8
F10
F9
E11
E10
F8
E9
D11
C10
C11
E8
D10
61
62
63
64
65
66
67
68
69
70
71
72
42
43
44
45
46
47
48
49
53
54
55
56
60
59
58
57
A10
B9
B11
A9
B8
A8
C8
C7
B7
B6
C6
A6
J11
J10
J8
H10
H9
G10
G9
F10
F9
E11
E10
E9
C10
C11
D9
D10
49
50
51
52
53
54
55
56
57
34
35
36
37
38
39
40
44
45
48
47
46
Page 30 of 118
CY9A140NB Series
Pin
Function
GPIO
Pin No
Pin Name
P30
P31
P32
P33
P34
P35
P36
P37
P38
P39
P3A
P3B
P3C
P3D
P3E
P3F
P40
P41
P42
P43
P44
P45
P46
P47
P48
P49
P4A
P4B
P4C
P4D
P4E
P50
P51
P52
P53
P54
P55
P56
P60
P61
P62
P63
P80
P81
PE0
PE2
PE3
Function Description
General-purpose I/O port 3
General-purpose I/O port 4
General-purpose I/O port 5
General-purpose I/O port 6
General-purpose I/O port 8
General-purpose I/O port E
Document Number: 002-05637 Rev. *C
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-64
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
27
28
29
30
31
32
36
37
39
40
41
42
43
44
45
2
3
4
5
6
7
8
96
95
94
93
98
99
46
48
49
87
88
89
90
91
92
93
94
95
96
97
98
99
100
1
2
5
6
7
8
9
10
14
15
17
18
19
20
21
22
23
80
81
82
83
84
85
86
74
73
72
71
76
77
24
26
27
E1
E2
E3
E4
F1
F2
F3
G1
G2
F4
G3
H1
H2
G4
H3
J2
J4
L5
K5
J5
H5
L6
L3
K3
K6
J6
L7
K7
H6
J7
K8
C1
C2
B3
D1
D2
D3
D5
C4
B4
C5
D6
A3
A2
K9
L9
L10
9
10
11
12
13
14
15
16
17
18
19
21
22
26
27
29
30
31
32
33
34
35
2
3
4
5
6
7
8
76
75
74
73
78
79
36
38
39
E2
E3
G1
G2
G3
H1
H2
H3
J1
J2
J4
L5
K5
L3
K3
J5
K6
J6
L7
K7
J7
K8
C1
C2
B3
D1
D2
D3
E1
C4
B4
C5
B5
A3
A2
K9
L9
L10
5
6
7
8
9
10
11
12
13
14
15
19
20
22
23
24
25
26
27
2
3
4
60
59
58
62
63
28
30
31
Page 31 of 118
CY9A140NB Series
Pin
Function
Multifunction
Serial
0
Pin No
Pin Name
SIN0_0
SIN0_1
SOT0_0
(SDA0_0)
SOT0_1
(SDA0_1)
SCK0_0
(SCL0_0)
SCK0_1
(SCL0_1)
Multifunction
Serial
1
SIN1_1
SOT1_1
(SDA1_1)
SCK1_1
(SCL1_1)
Function Description
Multi-function serial interface
ch.0 input pin
Multi-function serial interface
ch.0 output pin.
This pin operates as SOT0
when it is used in a
UART/CSIO (operation modes
0 to 2) and as SDA0 when it is
used in an I2C (operation mode
4).
Multi-function serial interface
ch.0 clock I/O pin.
This pin operates as SCK0
when it is used in a
UART/CSIO (operation modes
0 to 2) and as SCL0 when it is
used in an I2C (operation mode
4).
Multi-function serial interface
ch.1 input pin
Multi-function serial interface
ch.1 output pin.
This pin operates as SOT1
when it is used in a
UART/CSIO (operation modes
0 to 2) and as SDA1 when it is
used in an I2C (operation mode
4).
Multi-function serial interface
ch.1 clock I/O pin.
This pin operates as SCK1
when it is used in a
UART/CSIO (operation modes
0 to 2) and as SCL1 when it is
used in an I2C (operation mode
4).
Document Number: 002-05637 Rev. *C
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-64
73
51
C11
59
C11
48
56
34
H9
46
H9
-
72
50
E8
58
D9
47
57
35
H7
47
G10
-
71
49
D10
57
D10
46
58
36
G10
48
G9
-
53
31
J10
43
J10
35
54
32
J8
44
J8
36
55
33
H10
45
H10
37
Page 32 of 118
CY9A140NB Series
Pin
Function
Multifunction
Serial
2
Pin No
Pin Name
SIN2_2
SOT2_2
(SDA2_2)
SCK2_2
(SCL2_2)
Multifunction
Serial
3
SIN3_1
SIN3_2
SOT3_1
(SDA3_1)
SOT3_2
(SDA3_2)
SCK3_1
(SCL3_1)
SCK3_2
(SCL3_2)
Function Description
Multi-function serial interface
ch.2 input pin
Multi-function serial interface
ch.2 output pin.
This pin operates as SOT2
when it is used in a
UART/CSIO (operation modes
0 to 2) and as SDA2 when it is
used in an I2C (operation mode
4).
Multi-function serial interface
ch.2 clock I/O pin.
This pin operates as SCK2
when it is used in a
UART/CSIO (operation modes
0 to 2) and as SCL2 when it is
used in an I2C (operation mode
4).
Multi-function serial interface
ch.3 input pin
Multi-function serial interface
ch.3 output pin.
This pin operates as SOT3
when it is used in a
UART/CSIO (operation modes
0 to 2) and as SDA3 when it is
used in an I2C (operation mode
4).
Multi-function serial interface
ch.3 clock I/O pin.
This pin operates as SCK3
when it is used in a
UART/CSIO (operation modes
0 to 2) and as SCL3 when it is
used in an I2C (operation mode
4).
Document Number: 002-05637 Rev. *C
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-64
59
37
G9
49
F10
40
63
41
G8
53
F9
44
64
42
F10
54
E11
45
2
80
C1
2
C1
2
39
17
K6
29
J5
-
3
81
C2
3
C2
3
40
18
J6
30
K6
-
4
82
B3
4
B3
4
41
19
L7
31
J6
-
Page 33 of 118
CY9A140NB Series
Pin
Function
Multifunction
Serial
4
Pin No
Pin Name
Function Description
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-64
87
65
D7
67
C8
54
65
43
F9
55
E10
-
82
60
C8
-
-
-
88
66
A6
68
C7
55
66
44
E11
56
E9
-
83
61
D9
-
-
-
89
67
B6
69
B7
56
67
45
E10
-
-
-
84
62
A7
-
-
-
90
68
C6
70
B6
-
69
47
E9
-
-
-
86
64
C7
-
-
-
91
69
A5
71
C6
-
68
46
F8
-
-
-
CTS4_2
85
63
B7
-
-
-
SIN5_0
96
74
C4
76
C4
60
15
93
F3
-
-
-
95
73
B4
75
B4
59
16
94
G1
-
-
-
94
72
C5
74
C5
58
17
95
G2
-
-
-
SIN4_0
SIN4_1
Multi-function serial interface
ch.4 input pin
SIN4_2
SOT4_0
(SDA4_0)
SOT4_1
(SDA4_1)
SOT4_2
(SDA4_2)
SCK4_0
(SCL4_0)
SCK4_1
(SCL4_1)
SCK4_2
(SCL4_2)
Multi-function serial interface
ch.4 output pin.
This pin operates as SOT4
when it is used in a
UART/CSIO (operation modes
0 to 2) and as SDA4 when it is
used in an I2C (operation mode
4).
Multi-function serial interface
ch.4 clock I/O pin.
This pin operates as SCK4
when it is used in a
UART/CSIO (operation modes
0 to 2) and as SCL4 when it is
used in an I2C (operation mode
4).
RTS4_0
RTS4_1
Multi-function serial interface
ch.4 RTS output pin
RTS4_2
CTS4_0
CTS4_1
Multifunction
Serial
5
SIN5_2
SOT5_0
(SDA5_0)
SOT5_2
(SDA5_2)
SCK5_0
(SCL5_0)
SCK5_2
(SCL5_2)
Multi-function serial interface
ch.4 CTS input pin
Multi-function serial interface
ch.5 input pin
Multi-function serial interface
ch.5 output pin.
This pin operates as SOT5
when it is used in a
UART/CSIO (operation modes
0 to 2) and as SDA5 when it is
used in an I2C (operation mode
4).
Multi-function serial interface
ch.5 clock I/O pin.
This pin operates as SCK5
when it is used in a
UART/CSIO (operation modes
0 to 2) and as SCL5 when it is
used in an I2C (operation mode
4).
Document Number: 002-05637 Rev. *C
Page 34 of 118
CY9A140NB Series
Pin
Function
Multifunction
Serial
6
Pin No
Pin Name
SIN6_0
SIN6_1
SOT6_0
(SDA6_0)
SOT6_1
(SDA6_1)
SCK6_0
(SCL6_0)
SCK6_1
(SCL6_1)
Multifunction
Serial
7
SIN7_1
SOT7_1
(SDA7_1)
SCK7_1
(SCL7_1)
Function Description
Multi-function serial interface
ch.6 input pin
Multi-function serial interface
ch.6 output pin.
This pin operates as SOT6
when it is used in a
UART/CSIO (operation modes
0 to 2) and as SDA6 when it is
used in an I2C (operation mode
4).
Multi-function serial interface
ch.6 clock I/O pin.
This pin operates as SCK6
when it is used in a
UART/CSIO (operation modes
0 to 2) and as SCL6 when it is
used in an I2C (operation mode
4).
Multi-function serial interface
ch.7 input pin
Multi-function serial interface
ch.7 output pin.
This pin operates as SOT7
when it is used in a
UART/CSIO (operation modes
0 to 2) and as SDA7 when it is
used in an I2C (operation mode
4).
Multi-function serial interface
ch.7 clock I/O pin.
This pin operates as SCK7
when it is used in a
UART/CSIO (operation modes
0 to 2) and as SCL7 when it is
used in an I2C (operation mode
4).
Document Number: 002-05637 Rev. *C
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-64
5
83
D1
5
D1
-
12
90
E4
12
G2
8
6
84
D2
6
D2
-
11
89
E3
11
G1
7
7
85
D3
7
D3
-
10
88
E2
10
E3
6
45
23
K8
35
K8
27
44
22
J7
34
J7
26
43
21
H6
33
K7
25
Page 35 of 118
CY9A140NB Series
Pin
Function
Real-time
clock
Low-Power
Consumption
Mode
Pin No
Pin Name
RTCCO_0
RTCCO_1
RTCCO_2
SUBOUT_0
SUBOUT_1
SUBOUT_2
WKUP0
WKUP1
WKUP2
WKUP3
HDMICEC/
Remote
Control
Function Description
0.5 seconds pulse output pin of
Real-time clock
Sub clock output pin
Deep standby mode return
signal input pin 0
Deep standby mode return
signal input pin 1
Deep standby mode return
signal input pin 2
Deep standby mode return
signal input pin 3
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-64
92
55
19
92
55
19
70
33
97
70
33
97
B5
H10
G3
B5
H10
G3
72
45
14
72
45
14
A6
H10
H1
A6
H10
H1
57
37
10
57
37
10
92
70
B5
72
A6
57
53
31
J10
43
J10
35
73
51
C11
59
C11
48
96
74
C4
76
C4
60
CEC0
HDMI-CEC/Remote Control
Reception ch.0 input/output pin
43
21
H6
33
K7
25
CEC1
HDMI-CEC/Remote Control
Reception ch.1 input/output pin
96
74
C4
76
C4
60
Document Number: 002-05637 Rev. *C
Page 36 of 118
CY9A140NB Series
Pin
Function
Reset
Pin No
Pin Name
INITX
Mode
MD0
MD1
Power
GND
VCC
VCC
VCC
VCC
VCC
VCC
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
Function Description
External Reset Input pin.
A reset is valid when INITX=L.
Mode 0 pin.
During normal operation,
MD0=L must be input. During
serial programming to Flash
memory, MD0=H must be input.
Mode 1 pin.
During serial programming to
Flash memory, MD1=L must be
input.
Power supply Pin
Power supply Pin
Power supply Pin
Power supply Pin
Power supply Pin
Power supply Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
GND Pin
Document Number: 002-05637 Rev. *C
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-64
38
16
K4
28
K4
21
47
25
L8
37
L8
29
46
24
K9
36
K9
28
1
26
35
51
76
97
25
34
50
75
100
79
4
13
29
54
75
3
12
28
53
78
B1
J1
K1
K11
A10
A4
B2
L1
K2
J3
H4
L4
L11
K10
J9
H8
B10
C9
A11
D8
D4
C3
A1
1
25
41
77
20
24
40
80
B1
K1
K11
A4
F1
F2
F3
B2
L1
K2
J3
L6
L4
L11
K10
J9
B10
C9
D11
A11
A7
C3
A5
A1
1
18
33
61
16
32
64
Page 37 of 118
CY9A140NB Series
Pin
Function
Clock
ADC
power
Pin No
Pin Name
X0
X0A
X1
X1A
CROUT_0
CROUT_1
AVCC
AVRH
ADC
GND
C pin
Function Description
Main clock (oscillation) input pin
Sub clock (oscillation) input pin
Main clock (oscillation) I/O pin
Sub clock (oscillation) I/O pin
Built-in high-speed CR-osc clock
output port
A/D converter analog power
supply pin
A/D converter analog reference
voltage input pin
LQFP-100
QFP-100
BGA-112
LQFP-80
BGA-96
LQFP/
QFN-64
48
36
49
37
74
92
26
14
27
15
52
70
L9
L3
L10
K3
C10
B5
38
26
39
27
60
72
L9
L3
L10
K3
C10
A6
30
19
31
20
57
60
38
H11
50
H11
41
61
39
F11
51
F11
42
AVSS
A/D converter GND pin
62
40
G11
52
G11
43
C
Power stabilization capacity pin
33
11
L2
23
L2
17
Note:
−
While this device contains a Test Access Port (TAP) based on the IEEE 1149.1-2001 JTAG standard, it is not fully compliant to
all requirements of that standard. This device may contain a 32-bit device ID that is the same as the 32-bit device ID in other
devices with different functionality. The TAP pins may also be configurable for purposes other than access to the TAP
controller.
Document Number: 002-05637 Rev. *C
Page 38 of 118
CY9A140NB Series
5. I/O Circuit Type
Type
A
Circuit
Remarks
It is possible to select the main
oscillation / GPIO function
P
u
l
P-ch
When the main oscillation is selected.
−
: Approximately 1 MΩ
l
Digital
output
P-ch
-
X1
Oscillation feedback resistor
−
With Standby mode control
u
p
Digital
output
r
N-ch
e
R
s
i
s
Pull-up
resistor control
When the GPIO is selected.
−
CMOS level output.
−
CMOS level hysteresis input
−
With pull-up resistor control
−
With standby mode control
−
Pull-up resistor
: Approximately 33 kΩ
t
Digital
input
o
−
IOH = -4 mA, IOL = 4 mA
r
Standby mode control
Clock input
F
e
e
d
b
Standby mode control
a
c
Digital input
k
Standby mode control
P
r
R
P-ch
P-ch
X0
N-ch
u
e
l
s
l
i
s
u
t
p
o
r
r
Digital output
Digital output
e
s
i
s
Pull-up resistor control
t
o
r
Document Number: 002-05637 Rev. *C
Page 39 of 118
CY9A140NB Series
Type
B
Circuit
Remarks
−
CMOS level hysteresis input
−
Pull-up resistor
: Approximately 33 kΩ
Pull-up resistor
Digital input
C
Digital input
N-ch
Document Number: 002-05637 Rev. *C
−
Open drain output
−
CMOS level hysteresis input
Digital output
Page 40 of 118
CY9A140NB Series
Type
D
Circuit
Remarks
It is possible to select the sub
oscillation / GPIO function
P
u
l
P-ch
When the sub oscillation is selected.
−
l
Digital
output
P-ch
-
X1A
u
Oscillation feedback resistor
: Approximately 5 MΩ
−
With Standby mode control
p
When the GPIO is selected.
−
CMOS level output.
e
−
CMOS level hysteresis input
s
−
With pull-up resistor control
i
−
With standby mode control
s
Pull-up
resistor control
−
Pull-up resistor
r
Digital
output
N-ch
R
t
Digital
input
o
r
: Approximately 33 kΩ
−
IOH = -4 mA, IOL = 4 mA
Standby mode control
Clock input
F
e
e
d
b
Standby mode control
a
c
Digital input
k
Standby mode control
P
r
R
P-ch
P-ch
X0A
N-ch
u
e
l
s
l
i
s
u
t
p
o
r
r
Digital output
Digital output
e
s
i
s
Pull-up resistor control
t
o
r
Document Number: 002-05637 Rev. *C
Page 41 of 118
CY9A140NB Series
Type
E
Circuit
P-ch
P-ch
Remarks
−
CMOS level output
−
CMOS level hysteresis input
−
With pull-up resistor control
−
With standby mode control
−
Pull-up resistor
Digital output
: Approximately 33 kΩ
−
IOH = -4 mA, IOL = 4 mA
−
When this pin is used as an I2C pin, the
digital output P-ch transistor is always off
N-ch
Digital output
R
Pull-up resistor control
Digital input
Standby mode control
F
P-ch
P-ch
Digital output
−
CMOS level output
−
CMOS level hysteresis input
−
With input control
−
Analog input
−
With pull-up resistor control
−
With standby mode control
−
Pull-up resistor
: Approximately 33 kΩ
N-ch
Digital output
−
IOH = -4 mA, IOL = 4 mA
−
When this pin is used as an I2C pin, the
digital output P-ch transistor is always off
R
Pull-up resistor control
Digital input
Standby mode control
Analog input
Input control
Document Number: 002-05637 Rev. *C
Page 42 of 118
CY9A140NB Series
Type
G
Circuit
Remarks
−
CMOS level hysteresis input
−
CMOS level output
−
CMOS level hysteresis input
−
With standby mode control
Mode input
H
IOH = -12.0 mA, IOL = 10.5 mA
P-ch
N-ch
Digital output
Digital output
R
Digital input
Standby mode control
I
P-ch
P-ch
Digital output
−
CMOS level output
−
CMOS level hysteresis input
−
5 V tolerant
−
With pull-up resistor control
−
With standby mode control
−
Pull-up resistor
: Approximately 33 kΩ
N-ch
Digital output
−
IOH = -4 mA, IOL = 4 mA
−
Available to control PZR registers.
−
When this pin is used as an I2C pin, the
digital output P-ch transistor is always off
R
Pull-up resistor control
Digital input
Standby mode control
Document Number: 002-05637 Rev. *C
Page 43 of 118
CY9A140NB Series
6. Handling Precaution
Any semiconductor devices have inherently a certain rate of failure. The possibility of failure is greatly affected by the conditions in
which they are used (circuit conditions, environmental conditions, etc.). This page describes precautions that must be observed to
minimize the chance of failure and to obtain higher reliability from your Cypress semiconductor devices.
6.1
Precautions for Product Design
This section describes precautions when designing electronic equipment using semiconductor devices.
Absolute Maximum Ratings
Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of
certain established limits, called absolute maximum ratings. Do not exceed these ratings.
Recommended Operating Conditions
Recommended operating conditions are normal operating ranges for the semiconductor device. All the device's electrical
characteristics are warranted when operated within these ranges.
Always use semiconductor devices within the recommended operating conditions. Operation outside these ranges may adversely
affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on the datasheet. Users
considering application outside the listed conditions are advised to contact their sales representative beforehand.
Processing and Protection of Pins
These precautions must be followed when handling the pins which connect semiconductor devices to power supply and input/output
functions.
1. Preventing Over-Voltage and Over-Current Conditions
Exposure to voltage or current levels in excess of maximum ratings at any pin is likely to cause deterioration within the device,
and in extreme cases leads to permanent damage of the device. Try to prevent such overvoltage or over-current conditions at
the design stage.
2. Protection of Output Pins
Shorting of output pins to supply pins or other output pins, or connection to large capacitance can cause large current flows.
Such conditions if present for extended periods of time can damage the device.
Therefore, avoid this type of connection.
3. Handling of Unused Input Pins
Unconnected input pins with very high impedance levels can adversely affect stability of operation. Such pins should be
connected through an appropriate resistance to a power supply pin or ground pin.
Latch-up
Semiconductor devices are constructed by the formation of P-type and N-type areas on a substrate. When subjected to abnormally
high voltages, internal parasitic PNPN junctions (called thyristor structures) may be formed, causing large current levels in excess of
several hundred mA to flow continuously at the power supply pin. This condition is called latch-up.
CAUTION: The occurrence of latch-up not only causes loss of reliability in the semiconductor device, but can cause injury or
damage from high heat, smoke or flame. To prevent this from happening, do the following:
1. Be sure that voltages applied to pins do not exceed the absolute maximum ratings. This should include attention to abnormal
noise, surge levels, etc.
2. Be sure that abnormal current flows do not occur during the power-on sequence.
Observance of Safety Regulations and Standards
Most countries in the world have established standards and regulations regarding safety, protection from electromagnetic
interference, etc. Customers are requested to observe applicable regulations and standards in the design of products.
Fail-Safe Design
Any semiconductor devices have inherently a certain rate of failure. You must protect against injury, damage or loss from such
failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and
prevention of over-current levels and other abnormal operating conditions.
.
Document Number: 002-05637 Rev. *C
Page 44 of 118
CY9A140NB Series
Precautions Related to Usage of Devices
Cypress semiconductor devices are intended for use in standard applications (computers, office automation and other office
equipment, industrial, communications, and measurement equipment, personal or household devices, etc.).
CAUTION: Customers considering the use of our products in special applications where failure or abnormal operation may directly
affect human lives or cause physical injury or property damage, or where extremely high levels of reliability are demanded (such as
aerospace systems, atomic energy controls, sea floor repeaters, vehicle operating controls, medical devices for life support, etc.)
are requested to consult with sales representatives before such use. The company will not be responsible for damages arising from
such use without prior approval.
6.2
Precautions for Package Mounting
Package mounting may be either lead insertion type or surface mount type. In either case, for heat resistance during soldering, you
should only mount under Cypress’ recommended conditions. For detailed information about mount conditions, contact your sales
representative.
Lead Insertion Type
Mounting of lead insertion type packages onto printed circuit boards may be done by two methods: direct soldering on the board, or
mounting by using a socket.
Direct mounting onto boards normally involves processes for inserting leads into through-holes on the board and using the flow
soldering (wave soldering) method of applying liquid solder. In this case, the soldering process usually causes leads to be subjected
to thermal stress in excess of the absolute ratings for storage temperature. Mounting processes should conform to Cypress
recommended mounting conditions.
If socket mounting is used, differences in surface treatment of the socket contacts and IC lead surfaces can lead to contact
deterioration after long periods. For this reason it is recommended that the surface treatment of socket contacts and IC leads be
verified before mounting.
Surface Mount Type
Surface mount packaging has longer and thinner leads than lead-insertion packaging, and therefore leads are more easily deformed
or bent. The use of packages with higher pin counts and narrower pin pitch results in increased susceptibility to open connections
caused by deformed pins, or shorting due to solder bridges.
You must use appropriate mounting techniques. Cypress Inc. recommends the solder reflow method, and has established a ranking
of mounting conditions for each product. Users are advised to mount packages in accordance with Cypress ranking of
recommended conditions.
Lead-Free Packaging
CAUTION: When ball grid array (BGA) packages with Sn-Ag-Cu balls are mounted using Sn-Pb eutectic soldering, junction strength
may be reduced under some conditions of use.
Storage of Semiconductor Devices
Because plastic chip packages are formed from plastic resins, exposure to natural environmental conditions will cause absorption of
moisture. During mounting, the application of heat to a package that has absorbed moisture can cause surfaces to peel, reducing
moisture resistance and causing packages to crack. To prevent, do the following:
1. Avoid exposure to rapid temperature changes, which cause moisture to condense inside the product. Store products in
locations where temperature changes are slight.
2. Use dry boxes for product storage. Products should be stored below 70% relative humidity, and at temperatures between 5°C
and 30°C.
When you open Dry Package that recommends humidity 40% to 70% relative humidity.
3. When necessary, Cypress Inc. packages semiconductor devices in highly moisture-resistant aluminum laminate bags, with a
silica gel desiccant. Devices should be sealed in their aluminum laminate bags for storage.
4. Avoid storing packages where they are exposed to corrosive gases or high levels of dust.
Baking
Packages that have absorbed moisture may be de-moisturized by baking (heat drying). Follow the Cypress recommended
conditions for baking.
Condition: 125°C/24 h
Document Number: 002-05637 Rev. *C
Page 45 of 118
CY9A140NB Series
Static Electricity
Because semiconductor devices are particularly susceptible to damage by static electricity, you must take the following precautions:
1. Maintain relative humidity in the working environment between 40% and 70%. Use of an apparatus for ion generation may be
needed to remove electricity.
2. Electrically ground all conveyors, solder vessels, soldering irons and peripheral equipment.
3. Eliminate static body electricity by the use of rings or bracelets connected to ground through high resistance (on the level of 1
MΩ).
Wearing of conductive clothing and shoes, use of conductive floor mats and other measures to minimize shock loads is
recommended.
4. Ground all fixtures and instruments, or protect with anti-static measures.
5. Avoid the use of styrofoam or other highly static-prone materials for storage of completed board assemblies.
6.3
Precautions for Use Environment
Reliability of semiconductor devices depends on ambient temperature and other conditions as described above.
For reliable performance, do the following:
1. Humidity
Prolonged use in high humidity can lead to leakage in devices as well as printed circuit boards. If high humidity levels are
anticipated, consider anti-humidity processing.
2. Discharge of Static Electricity
When high-voltage charges exist close to semiconductor devices, discharges can cause abnormal operation. In such cases,
use anti-static measures or processing to prevent discharges.
3. Corrosive Gases, Dust, or Oil
Exposure to corrosive gases or contact with dust or oil may lead to chemical reactions that will adversely affect the device. If
you use devices in such conditions, consider ways to prevent such exposure or to protect the devices.
4. Radiation, Including Cosmic Radiation
Most devices are not designed for environments involving exposure to radiation or cosmic radiation. Users should provide
shielding as appropriate.
5. Smoke, Flame
CAUTION: Plastic molded devices are flammable, and therefore should not be used near combustible substances. If devices
begin to smoke or burn, there is danger of the release of toxic gases.
Customers considering the use of Cypress products in other special environmental conditions should consult with sales
representatives.
Document Number: 002-05637 Rev. *C
Page 46 of 118
CY9A140NB Series
7. Handling Devices
Power supply pins
In products with multiple VCC and VSS pins, respective pins at the same potential are interconnected within the device in order to
prevent malfunctions such as latch-up. However, all of these pins should be connected externally to the power supply or ground
lines in order to reduce electromagnetic emission levels, to prevent abnormal operation of strobe signals caused by the rise in the
ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with each Power supply pin and GND pin of this device at low impedance. It is also
advisable that a ceramic capacitor of approximately 0.1 µF be connected as a bypass capacitor between each Power supply pin and
GND pin, between AVCC pin and AVSS pin near this device.
Stabilizing supply voltage
A malfunction may occur when the power supply voltage fluctuates rapidly even though the fluctuation is within the recommended
operating conditions of the VCC power supply voltage. As a rule, with voltage stabilization, suppress the voltage fluctuation so that
the fluctuation in VCC ripple (peak-to-peak value) at the commercial frequency (50 Hz/60 Hz) does not exceed 10% of the VCC
value in the recommended operating conditions, and the transient fluctuation rate does not exceed 0.1 V/μs when there is a
momentary fluctuation on switching the power supply..
Crystal oscillator circuit
Noise near the X0/X1 and X0A/X1A pins may cause the device to malfunction. Design the printed circuit board so that X0/X1,
X0A/X1A pins, the crystal oscillator, and the bypass capacitor to ground are located as close to the device as possible.
It is strongly recommended that the PC board artwork be designed such that the X0/X1 and X0A/X1A pins are surrounded by
ground plane as this is expected to produce stable operation.
Evaluate oscillation of your using crystal oscillator by your mount board.
Sub crystal oscillator
This series sub oscillator circuit is low gain to keep the low current consumption.
The crystal oscillator to fill the following conditions is recommended for sub crystal oscillator to stabilize the oscillation.
Surface mount type
Size:
More than 3.2 mm × 1.5 mm
Load capacitance: Approximately 6 pF to 7 pF
Lead type
Load capacitance: Approximately 6 pF to 7 pF
Using an external clock
When using an external clock as an input of the main clock, set X0/X1 to the external clock input, and input the clock to X0. X1(PE3)
can be used as a general-purpose I/O port.
Similarly, when using an external clock as an input of the sub clock, set X0A/X1A to the external clock input, and input the clock to
X0A. X1A (P47) can be used as a general-purpose I/O port.
Example of Using an External Clock
Device
X0(X0A)
Can be used as
general-purpose
I/O ports.
Document Number: 002-05637 Rev. *C
X1(PE3),
X1A (P47)
Set as
External clock
input
Page 47 of 118
CY9A140NB Series
Handling when using Multi-function serial pin as I2C pin
If it is using the multi-function serial pin as I2C pins, P-ch transistor of digital output is always disabled. However, I2C pins need to
keep the electrical characteristic like other pins and not to connect to the external I2C bus system with power OFF.
C Pin
This series contains the regulator. Be sure to connect a smoothing capacitor (CS) for the regulator between the C pin and the GND
pin. Please use a ceramic capacitor or a capacitor of equivalent frequency characteristics as a smoothing capacitor.
However, some laminated ceramic capacitors have the characteristics of capacitance variation due to thermal fluctuation (F
characteristics and Y5V characteristics). Please select the capacitor that meets the specifications in the operating conditions to use
by evaluating the temperature characteristics of a capacitor. A smoothing capacitor of about 4.7 μF would be recommended for this
series.
C
Device
CS
VSS
GND
Mode pins (MD0)
Connect the MD pin (MD0) directly to VCC or VSS pins. Design the printed circuit board such that the pull-up/down resistor stays
low, as well as the distance between the mode pins and VCC pins or VSS pins is as short as possible and the connection
impedance is low, when the pins are pulled-up/down such as for switching the pin level and rewriting the Flash memory data. It is
because of preventing the device erroneously switching to test mode due to noise.
Notes on power-on
Turn power on/off in the following order or at the same time.
If not using the A/D converter, connect AVCC = VCC and AVSS = VSS.
Turning on:
VCC →AVCC → AVRH
Turning off:
AVRH → AVCC → VCC
Serial Communication
There is a possibility to receive wrong data due to the noise or other causes on the serial communication.
Therefore, design a printed circuit board so as to avoid noise.
Consider the case of receiving wrong data due to noise, perform error detection such as by applying a checksum of data at the end.
If an error is detected, retransmit the data.
Differences in features among the products with different memory sizes and between Flash memory
products and MASK products
The electric characteristics including power consumption, ESD, latch-up, noise characteristics, and oscillation characteristics among
the products with different memory sizes and between Flash memory products and MASK products are different because chip
layout and memory structures are different.
If you are switching to use a different product of the same series, please make sure to evaluate the electric characteristics.
Pull-Up function of 5 V tolerant I/O
Please do not input the signal more than VCC voltage at the time of Pull-Up function use of 5 V tolerant I/O.
Document Number: 002-05637 Rev. *C
Page 48 of 118
CY9A140NB Series
8. Block Diagram
TRSTX,TCK,
TDI,TMS
TDO
SWJ-DP
ETM*1
TRACEDx,
TRACECLK
TPIU*1
ROM
Table
SRAM0
8/16 Kbyte
Multi-layer AHB (Max 40 MHz)
Cortex-M3 Core I
@40 MHz(Max)
D
NVIC
Sys
AHB-APB Bridge:
APB0(Max 40 MHz)
Dual-Timer
WatchDog Timer
(Software)
Clock Reset
Generator
INITX
WatchDog Timer
(Hardware)
SRAM1
8/16 Kbyte
Flash I/F
Security
On-Chip Flash
64+32 Kbyte/
128+32 Kbyte/
256+32 Kbyte
DMAC
8ch.
CSV
Main
Osc
Sub
Osc
PLL
CR
4 MHz
AHB-AHB
Bridge
CLK
X0
X1
X0A
X1A
CROUT
Source Clock
CR
100 kHz
MADx
External Bus I/F*2
ADTGx
TIOAx
TIOBx
Unit 0
Unit 1
Base Timer
16-bit 8ch./
32-bit 4ch.
Power-On
Reset
LVD Ctrl
RTCCO,
SUBOUT
CRC
Accelerator
Watch Counter
External Interrupt
Controller
16-pin + NMI
INTx
NMIX
MODE-Ctrl
MD0,
MD1
P0x,
P1x,
WKUPx
HDMI-CEC/
Remote Reciver Control
Real-Time Clock
C
IRQ-Monitor
GPIO
CEC0,CEC1
MCSXx,
MOEX,
MWEX,
MALE,
MRDY,
MCLKOUT,
MDQMx
LVD
Regulator
AHB-APB Bridge : APB2 (Max 40 MHz)
ANxx
MADATAx
12-bit A/D Converter
AHB-APB Bridge : APB1 (Max 40 MHz)
AVCC,
AVSS,
AVRH
PIN-Function-Ctrl
.
.
.
PEx
Multi-Function Serial I/F
8ch.
(with FIFO ch.4 to ch.7)
HW flow control(ch.4)*2
Deep Standby Ctrl
SCKx
SINx
SOTx
CTS4
RTS4
*1: For the CY9AF141LB/MB, CY9AF142LB/MB, and CY9AF144LB/MB, ETM is not available.
*2: For the CY9AF141LB, CY9AF142LB and CY9AF144LB, the External Bus Interface is not available. And the Multi-function
Serial Interface does not support hardware flow control in these products.
Document Number: 002-05637 Rev. *C
Page 49 of 118
CY9A140NB Series
9. Memory Size
See “Memory size” in “1. Product Lineup” to confirm the memory size.
10. Memory Map
Memory Map (1)
Peripherals Area
0x41FF_FFFF
Reserved
0xFFFF_FFFF
Reserved
0xE010_0000
0xE000_0000
Cortex-M3 Private
Peripherals
0x4006_1000
0x4006_0000
0x4005_0000
0x4004_0000
0x4003_F000
Reserved
0x4003_C000
0x4003_B000
0x4003_A000
0x7000_0000
0x6000_0000
External Device
Area
Reserved
0x4003_9000
0x4003_8000
0x4003_7000
0x4003_6000
0x4003_5000
0x4400_0000
0x4200_0000
0x4000_0000
32Mbytes
Bit band alias
Peripherals
Reserved
0x2400_0000
0x2200_0000
0x1FFF_0000
0x0020_8000
0x0020_0000
See the next page
"lMemory Map (2)"
for the memory size
details.
0x0010_4000
0x0010_0000
0x4003_3000
0x4003_2000
0x4003_1000
0x4003_0000
0x4002_F000
0x4002_E000
32Mbytes
Bit band alias
Reserved
0x2008_0000
0x2000_0000
0x4003_4000
0x4002_8000
DMAC
Reserved
EXT-bus I/F
Reserved
RTC
Watch Counter
CRC
MFS
Reserved
LVD/DS mode
HDMI-CEC/
Remote Control Receiver
GPIO
Reserved
Int-Req.Read
EXTI
Reserved
CR Trim
Reserved
0x4002_7000
A/DC
0x4002_6000
Reserved
0x4002_5000
Base Timer
SRAM1
SRAM0
Reserved
Flash(Work area)
Reserved
Security/CR Trim
Reserved
0x4001_6000
0x4001_5000
Flash(Main area)
0x0000_0000
0x4001_3000
0x4001_2000
0x4001_1000
0x4001_0000
0x4000_1000
0x4000_0000
Document Number: 002-05637 Rev. *C
Dual Timer
Reserved
SW WDT
HW WDT
Clock/Reset
Reserved
Flash I/F
Page 50 of 118
CY9A140NB Series
Memory Map (2)
Refer to the programming manual for the detail of Flash main area.
CY9AB40N/A40N/340N/140N/150R, CY9B520M/320M/120M Series Flash Programming Manual
Document Number: 002-05637 Rev. *C
Page 51 of 118
CY9A140NB Series
Peripheral Address Map
Start address
End address
Bus
Peripherals
0x4000_0000
0x4000_0FFF
0x4000_1000
0x4000_FFFF
0x4001_0000
0x4001_0FFF
Clock/Reset Control
0x4001_1000
0x4001_1FFF
Hardware Watchdog timer
0x4001_2000
0x4001_2FFF
0x4001_3000
0x4001_4FFF
0x4001_5000
0x4001_5FFF
Dual Timer
0x4001_6000
0x4001_FFFF
Reserved
0x4002_0000
0x4002_4FFF
Reserved
0x4002_5000
0x4002_5FFF
Base Timer
0x4002_6000
0x4002_6FFF
Reserved
0x4002_7000
0x4002_7FFF
0x4002_8000
0x4002_DFFF
Reserved
0x4002_E000
0x4002_EFFF
Built-in CR trimming
0x4002_F000
0x4002_FFFF
Reserved
0x4003_0000
0x4003_0FFF
External Interrupt
0x4003_1000
0x4003_1FFF
Interrupt Source Check Register
0x4003_2000
0x4003_2FFF
Reserved
0x4003_3000
0x4003_3FFF
GPIO
0x4003_4000
0x4003_4FFF
HDMI-CEC/Remote control Receiver
0x4003_5000
0x4003_57FF
Low-Voltage Detector
0x4003_5800
0x4003_5FFF
0x4003_6000
0x4003_7FFF
0x4003_8000
0x4003_8FFF
Multi-function serial
0x4003_9000
0x4003_9FFF
CRC
0x4003_A000
0x4003_AFFF
Watch Counter
0x4003_B000
0x4003_BFFF
Real-time clock
0x4003_C000
0x4003_EFFF
Reserved
0x4003_F000
0x4003_FFFF
External bus interface
0x4004_0000
0x4005_FFFF
Reserved
0x4006_0000
0x4006_0FFF
0x4006_1000
0x41FF_FFFF
Document Number: 002-05637 Rev. *C
AHB
APB0
APB1
APB2
AHB
Flash memory I/F register
Reserved
Software Watchdog timer
Reserved
A/D Converter
Deep standby mode Controller
Reserved
DMAC register
Reserved
Page 52 of 118
CY9A140NB Series
11. Pin Status in Each CPU State
The terms used for pin status have the following meanings.
INITX=0
This is the period when the INITX pin is the L level.
INITX=1
This is the period when the INITX pin is the H level.
SPL=0
This is the status that the standby pin level setting bit (SPL) in the standby mode control register (STB_CTL) is set to 0.
SPL=1
This is the status that the standby pin level setting bit (SPL) in the standby mode control register (STB_CTL) is set to 1.
Input enabled
Indicates that the input function can be used.
Internal input fixed at 0
This is the status that the input function cannot be used. Internal input is fixed at L.
Hi-Z
Indicates that the pin drive transistor is disabled and the pin is put in the Hi-Z state.
Setting disabled
Indicates that the setting is disabled.
Maintain previous state
Maintains the state that was immediately prior to entering the current mode.
If a built-in peripheral function is operating, the output follows the peripheral function.
If the pin is being used as a port, that output is maintained.
Analog input is enabled
Indicates that the analog input is enabled.
Trace output
Indicates that the trace function can be used.
GPIO selected
In Deep standby mode, pins switch to the general-purpose I/O port.
Document Number: 002-05637 Rev. *C
Page 53 of 118
CY9A140NB Series
Pin status type
List of Pin Status
A
Function
group
Power-on
reset or
low-voltage
detection
state
Power
supply
unstable
-
INITX
input
state
Device
internal
reset
state
Power supply stable
INITX = 0
-
INITX = 1
-
Run
mode or
Sleep
mode
state
Power
supply
stable
INITX = 1
-
Timer mode,
RTC mode, or
Stop mode state
Deep standby RTC
mode or Deep
standby Stop mode
state
Power supply stable
Power supply stable
INITX = 1
SPL = 0
SPL = 1
INITX = 1
SPL = 0
SPL = 1
Return
from
Deep
standby
mode
state
Power
supply
stable
INITX = 1
-
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Main
crystal
oscillator
input pin/
External
main clock
input
selected
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Maintain
previous
state
Hi-Z /
Internal
input fixed
at "0"
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
External
main clock
input
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state
Maintain
previous
state/
When
oscillation
stops *1,
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state/
When
oscillation
stops *1,
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state/
When
oscillation
stops *1,
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state/
When
oscillation
stops *1,
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state/
When
oscillation
stops *1,
Hi-Z /
Internal
input fixed
at 0
B
Main
crystal
oscillator
output pin
Hi-Z /
Internal input
fixed at 0/
or Input
enabled
Hi-Z /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state/
When
oscillation
stops *1,
Hi-Z /
Internal
input fixed
at 0
C
INITX
input pin
Pull-up / Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Pull-up /
Input
enabled
D
Mode
input pin
Input enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Document Number: 002-05637 Rev. *C
Page 54 of 118
Pin status type
CY9A140NB Series
Function
group
Power-on
reset or
low-voltage
detection
state
Power
supply
unstable
-
INITX
input
state
Device
internal
reset
state
Run
mode or
Sleep
mode
state
INITX = 0
-
INITX = 1
-
Power
supply
stable
INITX = 1
-
Power supply stable
Timer mode,
RTC mode, or
Stop mode state
Deep standby RTC
mode or Deep
standby Stop mode
state
Power supply stable
Power supply stable
INITX = 1
SPL = 0
SPL = 1
INITX = 1
SPL = 0
SPL = 1
Return
from
Deep
standby
mode
state
Power
supply
stable
INITX = 1
-
Mode
input pin
Input enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Input
enabled
GPIO
selected
Hi-Z /
Input
enabled
GPIO
selected
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
E
F
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Sub
crystal
oscillator
input pin /
External
sub clock
input
selected
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Input
enabled
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
External
sub clock
input
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state
Hi-Z/
Internal
input fixed
at 0
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state/
When
oscillation
stops *2,
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state/
When
oscillation
stops *2,
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state/
When
oscillation
stops *2,
Hi-Z/
Internal
input fixed
at 0
Maintain
previous
state/
When
oscillation
stops *2,
Hi-Z/
Internal
input fixed
at 0
Maintain
previous
state/
When
oscillation
stops *2,
Hi-Z/
Internal
input fixed
at 0
G
Sub
crystal
oscillator
output pin
Hi-Z /
Internal input
fixed at 0 /
or Input
enable
Hi-Z /
Internal
input fixed
at 0
Document Number: 002-05637 Rev. *C
Hi-Z /
Internal
input fixed
at 0
Page 55 of 118
Pin status type
CY9A140NB Series
H
I
Function
group
Power-on
reset or
low-voltage
detection
state
Power
supply
unstable
-
INITX
input
state
Run
mode or
Sleep
mode
state
INITX = 0
-
INITX = 1
-
Power
supply
stable
INITX = 1
-
Hi-Z /
Input
enabled
Maintain
previous
state
Setting
disabled
Power supply stable
GPIO
selected
Hi-Z
Hi-Z /
Input
enabled
NMIX
selected
Setting
disabled
Setting
disabled
Resource
other than
above
selected
Device
internal
reset
state
Hi-Z
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
Hi-Z
Pull-up /
Input
enabled
Pull-up /
Input
enabled
Timer mode,
RTC mode, or
Stop mode state
Deep standby RTC
mode or Deep
standby Stop mode
state
Power supply
stable
Power supply stable
INITX = 1
SPL = 0
SPL = 1
INITX = 1
SPL = 0
SPL = 1
Maintain
previous
state
J
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Hi-Z
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
Setting
disabled
Setting
disabled
Setting
disabled
Resource
selected
K
GPIO
selected
External
interrupt
enabled
selected
L
Resource
other than
above
selected
Hi-Z
Hi-Z /
Input
enabled
GPIO
selected
Document Number: 002-05637 Rev. *C
Hi-Z /
Input
enabled
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
WKUP
input
enabled
Hi-Z /
WKUP
input
enabled
GPIO
selected
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
GPIO
selected
JTAG
selected
Return
from
Deep
standby
mode
state
Power
supply
stable
INITX = 1
-
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Page 56 of 118
Pin status type
CY9A140NB Series
Function
group
Analog
input
selected
Power-on
reset or
low-voltage
detection
state
Power
supply
unstable
-
Hi-Z
INITX
input
state
Device
internal
reset
state
Run
mode or
Sleep
mode
state
Power supply
stable
Power supply stable
INITX = 1
SPL = 0
SPL = 1
INITX = 1
SPL = 0
SPL = 1
INITX = 0
-
INITX = 1
-
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input
fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Hi-Z /
Internal
input
fixed at 0
/
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Hi-Z
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
GPIO
selected
Analog
input
selected
N
External
interrupt
enabled
selected
Resource
other than
above
selected
Maintain
previous
state
Setting
disabled
Setting
disabled
Setting
disabled
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
GPIO
selected
Trace
selected
O
Resource
other than
above
selected
GPIO
selected
Return
from
Deep
standby
mode
state
Power
supply
stable
INITX = 1
-
Power
supply
stable
INITX = 1
-
Power supply stable
M
Resource
other than
above
selected
Timer mode,
RTC mode, or
Stop mode state
Deep standby RTC
mode or Deep
standby Stop mode
state
Hi-Z
Hi-Z /
Input
enabled
Document Number: 002-05637 Rev. *C
Hi-Z /
Input
enabled
Hi-Z /
Internal
input fixed
at 0
Trace
output
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Page 57 of 118
Pin status type
CY9A140NB Series
Function
group
Analog
input
selected
P
Power-on
reset or
low-voltage
detection
state
Power
supply
unstable
-
Hi-Z
INITX
input
state
Device
internal
reset
state
Run
mode or
Sleep
mode
state
INITX = 0
-
INITX = 1
-
Power
supply
stable
INITX = 1
-
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Power supply stable
Timer mode,
RTC mode, or
Stop mode state
Deep standby RTC
mode or Deep
standby Stop mode
state
Power supply
stable
Power supply stable
INITX = 1
SPL = 0 SPL = 1
INITX = 1
SPL = 0
SPL = 1
Hi-Z /
Internal
input
fixed
at 0 /
Analog
input
enabled
Trace
selected
Resource
other than
above
selected
Q
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Hi-Z
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Maintain
previous
state
Hi-Z /
Internal
input
fixed at 0
/
Analog
input
enabled
Hi-Z /
Internal
input
fixed at 0
Hi-Z /
Internal
input
fixed at 0
/
Analog
input
enabled
Trace
selected
Trace
output
External
interrupt
enabled
selected
Maintain
previous
state
Resource
other than
above
selected
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Trace
output
GPIO
selected
Analog
input
selected
Hi-Z /
Internal
input
fixed
at 0 /
Analog
input
enabled
Return
from
Deep
standby
mode
state
Power
supply
stable
INITX = 1
-
Setting
disabled
Setting
disabled
GPIO
selected
Document Number: 002-05637 Rev. *C
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input
fixed at 0
Page 58 of 118
Pin status type
CY9A140NB Series
Function
group
Analog
input
selected
R
Power
supply
unstable
-
Hi-Z
INITX
input
state
Device
internal
reset
state
Run
mode or
Sleep
mode
state
INITX = 0
-
INITX = 1
-
Power
supply
stable
INITX = 1
-
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Power supply stable
Timer mode,
RTC mode, or
Stop mode state
Deep standby RTC
mode or Deep
standby Stop mode
state
Power supply
stable
Power supply
stable
INITX = 1
SPL = 0
SPL = 1
INITX = 1
SPL = 0
SPL = 1
Hi-Z /
Internal
input
fixed at 0
/
Analog
input
enabled
WKUP
enabled
External
interrupt
enabled
selected
Resource
other than
above
selected
GPIO
selected
Maintain
previous
state
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
WKUP
input
enabled
Hi-Z /
Internal
input
fixed at 0
/
Analog
input
enabled
Hi-Z /
WKUP
input
enabled
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input
fixed at 0
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
GPIO
selected
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Resource
other than
above
selected
GPIO
selected
Hi-Z
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
Maintain
previous
state
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
GPIO
selected
Internal
input fixed
at 0
Hi-Z /
Internal
input
fixed at 0
GPIO
selected
CEC
enabled
Setting
disabled
Setting
disabled
Setting
disabled
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
Maintain
previous
state
WKUP
enabled
T
Hi-Z /
Internal
input fixed
at 0 /
Analog
input
enabled
Return
from
Deep
standby
mode
state
Power
supply
stable
INITX = 1
-
Setting
disabled
CEC
enabled
S
Power-on
reset or
low-voltage
detection
state
External
interrupt
enabled
selected
Resource
other than
above
selected
GPIO
selected
Setting
disabled
Setting
disabled
Maintain
previous
state
Setting
disabled
Maintain
previous
state
Hi-Z
Hi-Z /
Input
enabled
Hi-Z /
Input
enabled
Maintain
previous
state
Hi-Z /
Internal
input fixed
at 0
WKUP
input
enabled
GPIO
selected
Internal
input fixed
at 0
Maintain
previous
state
Hi-Z /
WKUP
input
enabled
Hi-Z /
Internal
input
fixed at 0
Maintain
previous
state
GPIO
selected
*1: Oscillation is stopped at Sub Timer mode, Low-speed CR Timer mode, RTC mode, Stop mode, Deep Standby RTC mode, and
Deep Standby Stop mode.
*2: Oscillation is stopped at Stop mode and Deep Standby Stop mode.
Document Number: 002-05637 Rev. *C
Page 59 of 118
CY9A140NB Series
12. Electrical Characteristics
12.1 Absolute Maximum Ratings
Parameter
Rating
Symbol
Power supply voltage *1, *2
Analog power supply voltage *1, *3
Analog reference voltage *1, *3
VCC
AVCC
AVRH
Input voltage *1
VI
Min
VSS - 0.5
VSS - 0.5
VSS - 0.5
VSS - 0.5
VSS - 0.5
Analog pin input voltage
*1
VIA
VSS - 0.5
Output voltage *1
VO
VSS - 0.5
L level maximum output current *4
IOL
-
L level average output current *5
IOLAV
-
L level total maximum output current
L level total average output current *6
∑IOL
∑IOLAV
-
H level maximum output current *4
IOH
-
H level average output current *5
IOHAV
-
H level total maximum output current
H level total average output current *6
Power consumption
Storage temperature
∑IOH
∑IOHAV
PD
TSTG
- 55
Unit
Max
VSS + 4.6
VSS + 4.6
VSS + 4.6
VCC + 0.5
(≤ 4.6 V)
VSS + 6.5
AVCC + 0.5
(≤ 4.6 V)
VCC + 0.5
(≤ 4.6 V)
V
V
V
10
mA
39
mA
4
10.5
100
50
- 10
mA
mA
mA
mA
mA
39
-4
12
- 100
- 50
300
+ 150
mA
mA
mA
mA
mA
mW
°C
Remarks
V
V
5 V tolerant
V
V
P80/P81 pins
P80/P81 pins
P80/P81 pins
P80/P81 pins
*1: These parameters are based on the condition that VSS = AVSS = 0 V.
*2: VCC must not drop below VSS - 0.5 V.
*3: Ensure that the voltage does not to exceed VCC + 0.5 V, for example, when the power is turned on.
*4: The maximum output current is defined as the value of the peak current flowing through any one of the corresponding pins.
*5: The average output current is defined as the average current value flowing through any one of the corresponding pins for a
100 ms period.
*6: The total average output current is defined as the average current value flowing through all of corresponding pins for a 100 ms.
WARNING:
−
Semiconductor devices may be permanently damaged by application of stress (including, without limitation, voltage, current or
temperature) in excess of absolute maximum ratings.
Do not exceed any of these ratings.
Document Number: 002-05637 Rev. *C
Page 60 of 118
CY9A140NB Series
12.2 Recommended Operating Conditions
(VSS = AVSS = 0.0 V)
Parameter
Power supply voltage
Analog power supply voltage
Analog reference voltage
Smoothing capacitor
Operating temperature
Symbol
Conditions
VCC
AVCC
-
AVRH
-
AVRL
CS
TA
--
Value
Min
1.65 *2
1.65
2.7
AVCC
AVSS
1
- 40
Max
3.6
3.6
AVCC
AVCC
AVSS
10
+ 85
Unit
V
V
V
V
V
µF
°C
Remarks
AVCC = VCC
AVCC ≥ 2.7 V
AVCC< 2.7 V
For Regulator *1
*1: See "C Pin" in "7. Handling Devices" for the connection of the smoothing capacitor.
*2: In between less than the minimum power supply voltage and low voltage reset/interrupt detection voltage
or more, instruction execution and low voltage detection function by built-in High-speed CR (including Main PLL is used) or
built-in Low-speed CR is possible to operate only.
WARNING:
−
The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All
of the device's electrical characteristics are warranted when the device is operated under these conditions.
Any use of semiconductor devices will be under their recommended operating condition.
Operation under any conditions other than these conditions may adversely affect reliability of device and could result in device
failure.
No warranty is made with respect to any use, operating conditions or combinations not represented on this datasheet. If you
are considering application under any conditions other than listed herein, please contact sales representatives beforehand.
Document Number: 002-05637 Rev. *C
Page 61 of 118
CY9A140NB Series
12.3 DC Characteristics
12.3.1
Current Rating
(VCC = AVCC = 1.65 V to 3.6 V, VSS = AVSS = 0 V, TA = - 40°C to + 85°C)
Parameter
Symbol
Pin
name
ICC
Power supply
current
VCC
ICCS
Conditions
PLL
Rrun mode
CPU: 40 MHz,
Peripheral: 40 MHz
CPU: 40 MHz,
Peripheral: the clock stops
NOP operation
High-speed
CR
Rrun mode
Sub
Rrun mode
Low-speed
CR
Run mode
PLL
Sleep mode
High-speed
CR
Sleep mode
Sub
Sleep mode
Low-speed
CR
Sleep mode
Value
Typ *3
Max *4
Unit
Remarks
15.5
21
mA
*1, *5
8.7
12
mA
*1, *5
CPU/ Peripheral: 4 MHz *2
1.8
2.9
mA
*1
CPU/ Peripheral: 32 kHz
110
680
μA
*1, *6
CPU/ Peripheral: 100 kHz
125
700
μA
*1
Peripheral: 40 MHz
9
12.5
mA
*1, *5
Peripheral: 4 MHz *2
0.8
1.6
mA
*1
Peripheral: 32 kHz
96
670
μA
*1, *6
Peripheral: 100 kHz
110
680
μA
*1
*1: When all ports are fixed.
*2: When setting it to 4 MHz by trimming.
*3: TA=+25°C, VCC=3.6 V
*4: TA=+85°C, VCC=3.6 V
*5: When using the crystal oscillator of 4 MHz (Including the current consumption of the oscillation circuit)
*6: When using the crystal oscillator of 32 kHz (Including the current consumption of the oscillation circuit)
Document Number: 002-05637 Rev. *C
Page 62 of 118
CY9A140NB Series
Parameter
Symbol
Value
Pin
name
Conditions
Main Timer mode
ICCT
Sub Timer mode
ICCR
RTC mode
ICCH
Power supply
current
Stop mode
VCC
ICCHD
ICCRD
Deep Standby
Stop mode
Deep Standby
RTC mode
Unit
Remarks
Typ *2
Max *2
2.1
2.5
mA
*1, *3
-
3.4
mA
*1, *3
12
35
μA
*1, *4
-
330
μA
*1, *4
9.8
29
μA
*1, *4
-
280
μA
*1, *4
9
28
μA
*1
TA = + 85°C,
When LVD is off
-
270
μA
*1
TA = + 25°C,
When LVD is off,
When RAM is off
1.25
7
μA
*1, *4, *5
TA = + 25°C,
When LVD is off,
When RAM is on
5.3
18
μA
*1, *4, *5
70
μA
*1, *4, *5
100
μA
*1, *4, *5
1.9
9
μA
*1, *5
5.9
20
μA
*1, *5
75
μA
*1, *5
105
μA
*1, *5
TA = + 25°C,
When LVD is off
TA = + 85°C,
When LVD is off
TA = + 25°C,
When LVD is off
TA = + 85°C,
When LVD is off
TA = + 25°C,
When LVD is off
TA = + 85°C,
When LVD is off
TA = + 25°C,
When LVD is off
TA = + 85°C,
When LVD is off,
When RAM is off
TA = + 85°C,
When LVD is off,
When RAM is on
TA = + 25°C,
When LVD is off,
When RAM is off
TA = + 25°C,
When LVD is off,
When RAM is on
TA = + 85°C,
When LVD is off,
When RAM is off
TA = + 85°C,
When LVD is off,
When RAM is on
-
-
*1: When all ports are fixed.
*2: VCC=3.6 V
*3: When using the crystal oscillator of 4 MHz (Including the current consumption of the oscillation circuit)
*4: When using the crystal oscillator of 32 kHz (Including the current consumption of the oscillation circuit)
*5: RAM on/off setting is on-chip SRAM only.
Document Number: 002-05637 Rev. *C
Page 63 of 118
CY9A140NB Series
Low-Voltage Detection Current
(VCC = 1.65 V to 3.6 V, VDDI = 1.1 V to 1.3 V, VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Low-voltage detection
circuit (LVD) power
supply current
Symbol
ICCLVD
Pin
name
Value
Conditions
Typ
Max
Unit
Remarks
At operation
for reset
VCC = 3.6 V
0.13
0.3
μA
At not detect
At operation
for interrupt
VCC = 3.6 V
0.13
0.3
μA
At not detect
VCC
Flash Memory Current
(VCC = 1.65 V to 3.6 V, VDDI = 1.1 V to 1.3 V, VSS = 0 V, TA = - 40°C to + 85°C)
Parameter
Flash memory
write/erase
current
Symbol
ICCFLASH
Pin
name
VCC
Value
Conditions
At Write/Erase
Typ
9.5
Max
11.2
Unit
mA
Remarks
*1
*1: The current at which to write or erase Flash memory, ICCFLASH is added to ICC.
A/D Converter Current
(VCC = VCC28 = AVCC = 1.65 V to 3.6 V, VDDI = 1.1 V to 1.3 V, VSS = AVSS = 0 V, TA = - 40°C to +85°C)
Parameter
Power supply current
Reference power
supply current
Symbol
ICCAD
ICCAVRH
Document Number: 002-05637 Rev. *C
Pin
name
Conditions
Value
Typ
Max
Unit
At 1unit operation
0.27
0.42
mA
At stop
0.03
10
μA
At 1unit operation
AVRH=3.6 V
0.72
1.29
mA
At stop
0.02
2.6
μA
Remarks
AVCC
AVRH
Page 64 of 118
CY9A140NB Series
12.3.2
Pin Characteristics
(VCC = AVCC = 1.65 V to 3.6 V, VSS = AVSS = 0 V, TA = - 40°C to + 85°C)
Parameter
H level input
voltage
(hysteresis
input)
Symbol
Pin name
CMOS
hysteresis
input pin,
MD0, MD1
VIHS
5V tolerant
input pin
Conditions
VCC ≥ 2.7 V
VCC × 0.8
VCC < 2.7 V
VCC × 0.7
VCC ≥ 2.7 V
VCC × 0.8
VCC < 2.7 V
L level input
voltage
(hysteresis
input)
CMOS
hysteresis
input pin,
MD0, MD1
Value
Typ
Max
Unit
-
VCC + 0.3
V
-
VSS + 5.5
V
Remarks
VCC × 0.7
VCC ≥ 2.7 V
VCC × 0.2
VSS - 0.3
-
V
VCC < 2.7 V
VCC × 0.3
VCC ≥ 2.7 V
VCC × 0.2
VILS
5V tolerant
input pin
4 mA type
H level
output voltage
Min
VOH
VSS - 0.3
-
VCC < 2.7 V
V
VCC × 0.3
VCC ≥ 2.7 V,
IOH = - 4 mA
VCC - 0.5
VCC < 2.7 V,
IOH = - 2 mA
VCC - 0.45
-
VCC
V
VCC - 0.4
-
VCC
V
VSS
-
0.4
V
VSS
-
0.4
V
VCC = AVCC = AVRH =
VSS = AVSS = 0.0 V
-5
-
+5
μA
-
-
+1.8
μA
VCC ≥ 2.7 V
21
33
66
VCC < 2.7 V
-
-
134
-
-
5
15
VCC ≥ 2.7 V,
IOH = - 12 mA
P80/P81
VCC < 2.7 V,
IOH = - 6.5 mA
VCC ≥ 2.7 V,
IOL = 4 mA
4 mA type
L level
output voltage
VCC < 2.7 V,
IOL = 2 mA
VOL
VCC ≥ 2.7 V,
IOL = 10.5 mA
P80/P81
VCC < 2.7 V,
IOL = 5 mA
Input leak current
Pull-up resistor
value
Input capacitance
IIL
RPU
CIN
CEC0,
CEC1
kΩ
Pull-up pin
Other than
VCC,
VSS,
AVCC,
AVSS, AVRH
Document Number: 002-05637 Rev. *C
pF
Page 65 of 118
CY9A140NB Series
12.4 AC Characteristics
12.4.1
Main Clock Input Characteristics
(VCC = 1.65 V to 3.6 V, VSS = 0 V, TA = - 40°C to + 85°C)
Parameter
Input frequency
Pin
name
Symbol
fCH
X0,
X1
Value
Conditions
Min
Max
Unit
VCC ≥ 2.7 V
VCC < 2.7 V
4
4
48
20
MHz
When crystal oscillator is
connected
-
4
48
MHz
When using external
clock
-
20.83
250
ns
When using external
clock
Input clock cycle
tCYLH
Input clock pulse width
-
PWH/tCYLH,
PWL/tCYLH
45
55
%
Input clock rising time and
falling time
tCF,
tCR
-
-
5
ns
Internal operating
clock *1 frequency
Internal operating
clock[1] cycle time
Remarks
When using external
clock
When using external
clock
fCM
-
-
-
40
MHz
Master clock
fCC
-
-
-
40
MHz
Base clock (HCLK/FCLK)
fCP0
fCP1
-
-
-
40
40
MHz
MHz
APB0 bus clock *2
APB1 bus clock *2
fCP2
-
-
-
40
MHz
APB2 bus clock *2
tCYCC
-
-
25
-
ns
Base clock (HCLK/FCLK)
tCYCP0
tCYCP1
-
-
25
25
-
ns
ns
APB0 bus clock *2
APB1 bus clock *2
tCYCP2
-
-
25
-
ns
APB2 bus clock *2
*1: For more information about each internal operating clock, see Chapter 2-1: Clock in FM3 Family Peripheral Manual.
*2: For about each APB bus which each peripheral is connected to, see 8. Block Diagram in this datasheet.
X0
Document Number: 002-05637 Rev. *C
Page 66 of 118
CY9A140NB Series
12.4.2
Sub Clock Input Characteristics
(VCC = 1.65 V to 3.6 V, VSS = 0 V, TA = - 40°C to + 85°C)
Parameter
Pin
name
Symbol
Input frequency
fCL
Input clock cycle
tCYLL
Input clock pulse width
-
X0A,
X1A
Value
Conditions
Min
Typ
Unit
Max
Remarks
-
-
32.768
-
kHz
-
32
-
100
kHz
When crystal oscillator is
connected
When using external clock
-
10
-
31.25
μs
When using external clock
PWH/tCYLL,
PWL/tCYLL
45
-
55
%
When using external clock
X0A
12.4.3
Built-in CR Oscillation Characteristics
Built-in high-speed CR
(VCC = 1.65 V to 3.6 V, VSS = 0 V, TA = - 40°C to + 85°C)
Parameter
Clock frequency
Frequency stabilization
time
Symbol
fCRH
tCRWT
Value
Conditions
Min
Typ
Max
TA = + 25°C
VCC ≥ 2.7 V
3.96
4
4.04
TA = + 25°C
VCC < 2.7 V
3.9
4
4.1
TA =
- 40°C to + 85°C
3.84
4
4.16
TA =
- 40°C to + 85°C
2.8
-
5.2
-
-
-
30
Unit
Remarks
When trimming *1
MHz
When not trimming
μs
*2
*1: In the case of using the values in CR trimming area of Flash memory at shipment for frequency/temperature trimming.
*2: This is the time to stabilize the frequency of High-speed CR clock after setting trimming value.
This period is able to use High-speed CR clock as source clock.
Built-in low-speed CR
(VCC = 1.65 V to 3.6 V, VSS = 0 V, TA = - 40°C to + 85°C)
Parameter
Clock frequency
Symbol
fCRL
Document Number: 002-05637 Rev. *C
Conditions
-
Value
Min
50
Typ
100
Max
150
Unit
Remarks
kHz
Page 67 of 118
CY9A140NB Series
12.4.4
Operating Conditions of Main PLL (In the case of using main clock for input of PLL)
(VCC = 1.65 V to 3.6 V, VSS = 0 V, TA = - 40°C to + 85°C)
Parameter
PLL oscillation stabilization wait time *1
(LOCK UP time)
PLL input clock frequency
PLL multiple rate
PLL macro oscillation clock frequency
Main PLL clock frequency *2
Symbol
Value
Typ
Min
Max
Unit
tLOCK
100
-
-
μs
fPLLI
fPLLO
fCLKPLL
4
5
75
-
-
16
37
150
40
MHz
multiple
MHz
MHz
Remarks
*1: Time from when the PLL starts operating until the oscillation stabilizes.
*2: For more information about Main PLL clock (CLKPLL), see Chapter 2-1: Clock in FM3 Family Peripheral Manual.
12.4.5
Operating Conditions of Main PLL (In the case of using the built-in High-speed CR for the input clock of
the Main PLL)
(VCC = 1.65 V to 3.6 V, VSS = 0 V, TA = - 40°C to + 85°C)
Parameter
Symbol
Value
Min
Typ
Max
Unit
PLL oscillation stabilization wait time *1
(LOCK UP time)
tLOCK
100
-
-
μs
PLL input clock frequency
PLL multiple rate
PLL macro oscillation clock frequency
Main PLL clock frequency *2
fPLLI
fPLLO
fCLKPLL
3.8
19
4
-
4.2
35
MHz
multiple
MHz
MHz
72
-
150
40
Remarks
*1: Time from when the PLL starts operating until the oscillation stabilizes.
*2: For more information about Main PLL clock (CLKPLL), see Chapter 2-1: Clock in FM3 Family Peripheral Manual.
Note:
−
Make sure to input to the Main PLL source clock, the High-speed CR clock (CLKHC) that the frequency/temperature
has been trimmed.
When setting PLL multiple rate, please take the accuracy of the built-in High-speed CR clock into account and prevent the
master clock from exceeding the maximum frequency.
Main PLL connection
Main clock (CLKMO)
High-speed CR clock (CLKHC)
K
divider
PLL input
clock
PLL macro
oscillation clock
Main
PLL
M
divider
Main PLL
clock
(CLKPLL)
N
divider
Document Number: 002-05637 Rev. *C
Page 68 of 118
CY9A140NB Series
12.4.6
Reset Input Characteristics
(VCC = 1.65 V to 3.6 V, VSS = 0 V, TA = - 40°C to + 85°C)
Parameter
Symbol
Reset input time
12.4.7
tINITX
Pin name
Value
Conditions
INITX
-
Min
Unit
Max
500
-
Remarks
ns
Power-on Reset Timing
(VSS = 0V, TA = - 40°C to + 85°C)
Parameter
Symbol
Power supply shut down time
Power ramp rate
Pin name
Conditions
dV/dt
VCC
Unit
Remarks
Min
Typ
Max
-
1
-
-
ms
*1
Vcc:0.2 V to 1.65 V
0.2
-
1000
mV/μs
*2
-
1.34
-
16.09
ms
tOFF
Time until releasing Power-on
reset
Value
tPRT
*1: VCC must be held below 0.2 V for minimum period of tOFF. Improper initialization may occur if this condition is not met.
*2: This dV/dt characteristic is applied at the power-on of cold start (tOFF>1 ms).
Note:
−
If tOFF cannot be satisfied designs must assert external reset(INITX) at power-up and at any brownout event per “12. 4. 6.Reset
Input Characteristics”.
1.65V
VCC
VDH
0.2V
dV/dt
0.2V
tPRT
Internal RST
CPU Operation
RST Active
0.2V
tOFF
release
start
Glossary:
VDH: detection voltage of Low Voltage detection reset. See “12.6 Low-Voltage Detection Characteristics”
Document Number: 002-05637 Rev. *C
Page 69 of 118
CY9A140NB Series
12.4.8
External Bus Timing
External bus clock output characteristics
(VCC = 1.65 V to 3.6 V, VSS = 0 V, TA = - 40°C to + 85°C)
Parameter
Output frequency
Symbol
Pin name
MCLKOUT *1
tCYCLE
Value
Conditions
Min
Max
Unit
VCC ≥ 2.7 V
-
40
MHz
VCC < 2.7 V
-
20
MHz
*1: The external bus clock output (MCLKOUT) is a divided clock of HCLK.
For more information about setting of clock divider, see Chapter 12: External Bus Interface in FM3 Family Peripheral Manual.
When external bus clock is not output, this characteristic does not give any effect on external bus operation.
MCLKOUT
External bus signal input/output characteristics
(VCC = 1.65 V to 3.6 V, VSS = 0 V, TA = - 40°C to + 85°C)
Parameter
Symbol
Conditions
VIH
Value
Unit
0.8 × VCC
V
0.2 × VCC
V
VOH
0.8 × VCC
V
VOL
0.2 × VCC
V
Remarks
Signal input characteristics
VIL
Signal output characteristics
Input signal
VIH
VIL
VIH
VIL
Output signal
VOH
VOL
VOH
VOL
Document Number: 002-05637 Rev. *C
Page 70 of 118
CY9A140NB Series
Separate Bus Access Asynchronous SRAM Mode
(VCC = 1.65 V to 3.6 V, VSS = 0 V, TA = - 40°C to + 85°C)
Parameter
MOEX
Min pulse width
MCSX ↓ → Address output
delay time
MOEX ↑ →
Address hold time
MCSX ↓ →
MOEX ↓ delay time
MOEX ↑ →
MCSX ↑ time
MCSX ↓ →
MDQM ↓ delay time
Data set up →
MOEX ↑ time
MOEX ↑ →
Data hold time
MWEX
Min pulse width
MWEX ↑ → Address output
delay time
MCSX ↓ →
MWEX ↓ delay time
MWEX ↑ →
MCSX ↑ delay time
MCSX ↓→
MDQM ↓ delay time
MWEX ↓→
Data output time
MWEX ↑ →
Data hold time
Symbol
tOEW
tCSL – AV
tOEH - AX
tCSL - OEL
tOEH - CSH
tCSL - RDQML
tDS - OE
tDH - OE
Pin name
MOEX
MCSX[7:0],
MAD[24:0]
MOEX,
MAD[24:0]
MOEX,
MCSX[7:0]
MCSX,
MDQM[1:0]
MOEX,
MADATA[15:0]
MOEX,
MADATA[15:0]
tWEW
MWEX
tWEH - AX
MWEX,
MAD[24:0]
tCSL - WEL
tWEH - CSH
tCSL-WDQML
tCSL - DV
tWEH - DX
MWEX,
MCSX[7:0]
MCSX,
MDQM[1:0]
MCSX,
MADATA[15:0]
MWEX,
MADATA[15:0]
Value
Conditions
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
Min
Unit
Max
MCLK×n-3
-
-9
-12
MCLK×m-9
MCLK×m-12
30
38
+9
+12
MCLK×m+9
MCLK×m+12
MCLK×m+9
MCLK×m+12
MCLK×m+9
MCLK×m+12
MCLK×m+9
MCLK×m+12
-
0
-
ns
MCLK×n-3
-
ns
0
MCLK×m-9
MCLK×m-12
0
0
MCLK×n-9
MCLK×n-12
0
MCLK×n-9
MCLK×n-12
MCLK-9
MCLK-12
0
ns
MCLK×m+9
MCLK×m+12
MCLK×n+9
MCLK×n+12
MCLK×m+9
MCLK×m+12
MCLK×n+9
MCLK×n+12
MCLK+9
MCLK+12
MCLK×m+9
MCLK×m+12
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Note:
−
When the external load capacitance CL = 30 pF (m = 0 to 15, n = 1 to 16).
Document Number: 002-05637 Rev. *C
Page 71 of 118
CY9A140NB Series
MCLK
MCSX[7:0]
MAD[24:0]
MOEX
MDQM[1:0]
MWEX
MADATA[15:0]
Document Number: 002-05637 Rev. *C
Page 72 of 118
CY9A140NB Series
Separate Bus Access Synchronous SRAM Mode
(VCC = 1.65 V to 3.6 V, VSS = 0 V, TA = - 40°C to + 85°C)
Parameter
Address delay time
Symbol
tAV
tCSL
MCSX delay time
tCSH
tREL
MOEX delay time
tREH
Data set up →
MCLK ↑ time
MCLK ↑ →
Data hold time
tDS
tDH
tWEL
MWEX delay time
tWEH
MDQM[1:0]
delay time
MCLK ↑ →
Data output time
MCLK ↑ →
Data hold time
tDQML
tDQMH
tODS
tOD
Pin name
MCLK,
MAD[24:0]
MCLK,
MCSX[7:0]
MCLK,
MOEX
MCLK,
MADATA[15:0]
MCLK,
MADATA[15:0]
MCLK,
MWEX
MCLK,
MDQM[1:0]
MCLK,
MADATA[15:0]
MCLK,
MADATA[15:0]
Value
Conditions
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC < 2.7 V
VCC ≥ 2.7 V
VCC
工商网监
湘ICP备2023018690号
