PALCE20V8L-25

USE ULTRA37000TM FOR ALL NEW DESIGNS PALCE20V8 Flash-Erasable Reprogrammable CMOS PAL® Device Features • Active pull-up on data input pins • Low power version (20V8L) — 55 mA max. commercial (15, 25 ns) — 65 mA max. military/industrial (15, 25 ns) • Standard version has low power — 90 mA max. commercial (15, 25 ns) — 115 mA max. commercial (10 ns) — 130 mA max. military/industrial (15, 25 ns) • CMOS Flash technology for electrical erasability and reprogrammability • User-programmable macrocell — Output polarity control — Individually selectable for registered or combinatorial operation • QSOP package available — 10, 15, and 25 ns com’l version — 15, and 25 ns military/industrial versions • High reliability — Proven Flash technology — 100% programming and functional testing Functional Description The Cypress PALCE20V8 is a CMOS Flash Erasable second-generation programmable array logic device. It is implemented with the familiar sum-of-product (AND-OR) logic structure and the programmable macrocell. The PALCE20V8 is executed in a 24-pin 300-mil molded DIP, a 300-mil cerdip, a 28-lead square ceramic leadless chip carrier, a 28-lead square plastic leaded chip carrier, and a 24-lead quarter size outline. The device provides up to 20 inputs and 8 outputs. The PALCE20V8 can be electrically erased and reprogrammed. The programmable macrocell enables the device to function as a superset to the familiar 24-pin PLDs such as 20L8, 20R8, 20R6, 20R4. Logic Block Diagram (PDIP/CDIP/QSOP) GND 12 I10 11 I9 10 I8 9 I7 8 I6 7 I5 6 I4 5 I3 4 I2 3 I1 2 CLK/I0 1 PROGRAMMABLE AND ARRAY (64 x 40) 8 8 8 8 8 8 8 8 MUX Macrocell Macrocell Macrocell Macrocell Macrocell Macrocell Macrocell Macrocell MUX 13 OE/I11 14 I12 15 I/O0 16 I/O1 17 I/O2 18 I/O3 19 I/O4 20 I/O5 21 I/O6 22 I/O7 23 I13 24 VCC Cypress Semiconductor Corporation Document #: 38-03026 Rev. *B • 3901 North First Street • San Jose, CA 95134 • 408-943-2600 Revised April 19, 2004 USE ULTRA37000TM FOR ALL NEW DESIGNS Pin Configuration DIP/QSOP Top View CLK/I0 I1 I2 I3 I4 I5 I6 I7 I8 I9 I10 GND 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 VCC I13 I/O7 I/O6 I/O5 I/O4 I/O3 I/O2 I/O1 I/O0 I12 OE/I11 PALCE20V8 PLCC/LCC Top View I2 I1 CLK/I 0 NC VCC I13 I/O7 4 3 2 1 2827 26 I3 I4 I5 NC I6 I7 I8 5 6 7 8 9 10 11 25 24 23 22 21 20 19 I/O6 I/O5 I/O4 NC I/O3 I/O2 I/O1 121314 1516 1718 Selection Guide tPD ns Generic Part Number PALCE20V8−5 PALCE20V8−7 PALCE20V8−10 PALCE20V8−15 PALCE20V8−25 PALCE20V8L−15 PALCE20V8L−25 Com’l/Ind 5 7.5 10 15 25 15 25 10 15 25 15 25 Mil 3 7 10 12 15 12 15 10 12 20 12 20 tS ns Com’l/Ind Mil 4 5 7 10 12 10 12 10 12 20 12 20 tCO ns Com’l/Ind Mil 115 115 115 90 90 55 55 130 130 130 65 65 ICC mA Com’l Mil/Ind Shaded areas contain preliminary information. Document #: 38-03026 Rev. *B I9 I10 GND NC OE/I 11 I12 I/O0 Page 2 of 14 USE ULTRA37000TM FOR ALL NEW DESIGNS Functional Description The PALCE20V8 features 8 product terms per output and 40 input terms into the AND array. The first product term in a macrocell can be used either as an internal output enable control or as a data product term. There are a total of 18 architecture bits in the PALCE20V8 macrocell; two are global bits that apply to all macrocells and 16 that apply locally, two bits per macrocell. The architecture bits determine whether the macrocell functions as a register or combinatorial with inverting or noninverting output. The output enable control can come from an external pin or internally from a product term. The output can also be permanently enabled, functioning as a dedicated output or permanently disabled, functioning as a dedicated input. Feedback paths are selectable from either the input/output pin associated with the macrocell, the input/output pin associated with an adjacent pin, or from the macrocell register itself. Power-Up Reset All registers in the PALCE20V8 power-up to a logic LOW for predictable system initialization. For each register, the associated output pin will be HIGH due to active-LOW outputs. Electronic Signature PALCE20V8 An electronic signature word is provided in the PALCE20V8 that consists of 64 bits of programmable memory that can contain user-defined data. Security Bit A security bit is provided that defeats the readback of the internal programmed pattern when the bit is programmed. Low Power The Cypress PALCE20V8 provides low-power operation through the use of CMOS technology, and increased testability with Flash reprogrammability. Product Term Disable Product Term Disable (PTD) fuses are included for each product term. The PTD fuses allow each product term to be individually disabled. Input and I/O Pin Pull-Ups The PALCE20V8 input and I/O pins have built-in active pull-ups that will float unused inputs and I/Os to an active HIGH state (logical 1). All unused inputs and three-stated I/O pins should be connected to another active input, VCC, or Ground to improve noise immunity and reduce ICC. Configuration Table CG0 0 0 1 1 1 CG1 1 1 0 0 1 CL0x 0 1 0 1 1 Cell Configuration Registered Output Combinatorial I/O Combinatorial Output Input Combinatorial I/O Devices Emulated Registered Med PALs Registered Med PALs Small PALs Small PALs 20L8 only Macrocell OE VCC 0X 10 11 10 00 01 To Adjacent Macrocell 11 CG1 CL0x 11 0X D Q Q 10 11 0X CG1 for pin 16 to 21 (DIP) CG0 for pin 15 and 22 (DIP) CL0x 10 I/Ox VCC CLK CL1x From Adjacent Pin Document #: 38-03026 Rev. *B Page 3 of 14 USE ULTRA37000TM FOR ALL NEW DESIGNS Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ..................................... −65°C to +150°C Ambient Temperature with Power Applied .................................................. −55°C to +125°C Supply Voltage to Ground Potential (Pin 24 to Pin 12).................................................−0.5V to +7.0V DC Voltage Applied to Outputs in High-Z State .....................................................−0.5V to +7.0V PALCE20V8 DC Input Voltage ................................................. −0.5V to +7.0V Output Current into Outputs (LOW)............................. 24 mA DC Programming Voltage............................................. 12.5V Latch-up Current...................................................... >200 mA Operating Range[1] Range Commercial Industrial Military[2] Ambient Temperature 0°C to +75°C −40°C to +85°C −55°C to +125°C VCC 5V ±5% 5V ±10% 5V ±10% Electrical Characteristics Over the Operating Range[3] Parameter VOH VOL VIH VIL IIH IIL[6] ISC ICC [5] Description Output HIGH Voltage Output LOW Voltage Input HIGH Level Input LOW Level Input or I/O HIGH Leakage Current Input or I/O LOW Leakage Current Operating Power Supply Current VCC = Min., VIN = VIH or VIL VCC = Min., VIN = VIH or VIL Test Conditions IOH = −3.2 mA IOH = −2 mA IOL = 24 mA IOL = 12 mA Com’l Mil/Ind Com’l Mil/Ind Min. 2.4 Max. Unit V 0.5 2.0 −0.5 0.8 10 −100 −30 −150 115 90 55 V V V µA µA mA mA mA mA mA mA Guaranteed Input Logical HIGH Voltage for All Inputs[4] Guaranteed Input Logical LOW Voltage for All 3.5V < VIN < VCC 0V < VIN < VIN (Max.) Inputs[4] Output Short Circuit Current VCC = Max., VOUT = 0.5V[7,8] VCC = Max., VIL = 0V, VIH = 3V, Output Open, f = 15 MHz (counter) 5, 7, 10 ns 15, 25 ns 15L, 25L ns 10, 15, 25 ns 15L, 25L ns Mil/Ind Mil/Ind Com’l 130 65 Capacitance[8] Parameter CIN COUT Description Input Capacitance Output Capacitance Test Conditions VIN = 2.0V @ f = 1 MHz VOUT = 2.0V @ f = 1 MHz Typ. 5 5 Unit pF pF Endurance Characteristics[8] Parameter N Description Minimum Reprogramming Cycles Test Conditions Normal Programming Conditions Min. 100 Max. Unit Cycles Notes: 1. The Voltage on any input or I/O pin cannot exceed the power pin during power-up. 2. TA is the “instant on” case temperature. 3. See the last page of this specification for Group A subgroup testing information. 4. These are absolute values with respect to device ground. All overshoots due to system or tester noise are included. 5. VIL (Min.) is equal to −3.0V for pulse durations less than 20 ns. 6. The leakage current is due to the internal pull-up resistor on all pins. 7. Not more than one output should be tested at a time. Duration of the short circuit should not be more than one second. VOUT = 0.5V has been chosen to avoid test problems caused by tester ground degradation. 8. Tested initially and after any design or process changes that may affect these parameters. Document #: 38-03026 Rev. *B Page 4 of 14 USE ULTRA37000TM FOR ALL NEW DESIGNS AC Test Loads and Waveforms ALL INPUT PULSES 3.0V 90% GND ≤ 2 ns 10% 90% 10% ≤ 2 ns PALCE20V8 5V S1 R1 OUTPUT R2 CL TEST POINT Commercial Specification tPD, tCO tPZX, tEA tPXZ, tER Closed Z ⎜ H: Open Z ⎜ L: Closed H ⎜ Z: Open L ⎜ Z: Closed 5 pF S1 CL 50 pF R1 200Ω R2 390Ω R1 Military R2 750Ω Measured Output Value 1.5V 1.5V H ⎜ Z: VOH − 0.5V L ⎜ Z: VOL + 0.5V 390Ω Commercial and Industrial Switching Characteristics [3] 20V8−5 Parameter tPD tPZX tPXZ tEA tER tCO tS tH tP Description Input to Output Propagation Delay[9] OE to Output Enable OE to Output Disable Input to Output Enable Delay[8] Input to Output Disable Delay[8,10] Clock to Output Delay[9] Input or Feedback Set-up Time Input Hold Time External Clock Period (tCO + tS) 1 3 0 7 Min. 1 Max. 5 5 5 6 6 4 1 7 0 12 20V8−7 Min. 1 Max. 7.5 6 6 9 9 5 1 10 0 17 20V8−10 Min. 1 Max. 10 10 10 10 10 7 1 12 0 22 20V8−15 Min. 1 Max. 15 15 15 15 15 10 1 15 0 27 20V8−25 Min. 1 Max. 25 20 20 25 25 12 Unit ns ns ns ns ns ns ns ns ns Shaded areas contain preliminary information. Notes: 9. Min. times are tested initially and after any design or process changes that may affect these parameters. 10. This parameter is measured as the time after OE pin or internal disable input disables or enables the output pin. This delay is measured to the point at which a previous HIGH level has fallen to 0.5 volts below VOH min. or a previous LOW level has risen to 0.5 volts above VOL max. 11. This specification indicates the guaranteed maximum frequency at which a state machine configuration with external feedback can operate. 12. This specification indicates the guaranteed maximum frequency at which the device can operate in data path mode. 13. This specification indicates the guaranteed maximum frequency at which a state machine configuration with internal only feedback can operate. 14. This parameter is calculated from the clock period at fMAX internal (1/fMAX3) as measured (see Note 7 above) minus tS. Document #: 38-03026 Rev. *B Page 5 of 14 USE ULTRA37000TM FOR ALL NEW DESIGNS Commercial and Industrial Switching Characteristics (continued)[3] 20V8−5 Parameter tWH tWL fMAX1 fMAX2 fMAX3 tCF tPR Description Clock Width HIGH [8] PALCE20V8 20V8−15 Min. 8 8 45.5 62.5 50 6 8 1 1 Max. 20V8−25 Min. 12 12 37 41.6 40 10 Max. Unit ns ns MHz MHz MHz ns µs 20V8−7 Min. 5 5 83 100 100 Max. 20V8−10 Min. 8 8 58 62.5 62.5 Max. Min. 3 3 143 Max. Clock Width LOW[8] External Maximum Frequency (1/(tCO + tS))[8,11] Data Path Maximum 166.6 Frequency (1/(tWH + tWL))[8, 12] Internal Feedback Maximum Frequency (1/(tCF + tS))[8,13] Register Clock to Feedback Input[8, 14] Power-Up Reset Time[8] 1 166.6 3 3 1 1 Military Switching Characteristics[3] 20V8−10 Parameter tPD tPZX tPXZ tEA tER tCO tS tH tP tWH tWL fMAX1 fMAX2 fMAX3 tCF tPR Description Input to Output Propagation Delay[9] OE to Output Enable OE to Output Disable Input to Output Enable Clock to Output Input Hold Time External Clock Period (tCO + tS) Clock Width HIGH[8] Clock Width LOW[8] External Maximum Frequency (1/(tCO + tS)[8,11] Data Path Maximum Frequency (1/(tWH + tWL))[8, 12 ] Internal Feedback Maximum Frequency (1/(tCF + tS))[8,13] Register Clock to Feedback Input[8, 14] Power-Up Reset Time[8] 1 Delay[8] 1 10 0 20 8 8 50 62.5 62.5 6 1 Input to Output Disable Delay[8,10] Delay[9] Input or Feedback Set-Up Time Min. 1 Max. 10 10 10 10 10 10 1 12 0 24 10 10 41.7 50 50 8 1 20V8−15 Min. 1 Max. 15 15 15 15 15 12 1 20 0 40 15 15 25 33.3 33.3 10 20V8−25 Min. 1 Max. 25 20 20 25 25 20 Unit ns ns ns ns ns ns ns ns ns ns ns MHz MHz MHz ns µs Document #: 38-03026 Rev. *B Page 6 of 14 USE ULTRA37000TM FOR ALL NEW DESIGNS Switching Waveform INPUTS, I/O, REGISTERED FEEDBACK tS CP t CO REGISTERED OUTPUTS t PD COMBINATORIAL OUTPUTS tPXZ, tER [11] PALCE20V8 tH t WH t WL tP tPXZ, tER[11] tEA, tPZX[11] [11] tEA, tPZX Power-Up Reset Waveform POWER SUPPLY VOLTAGE REGISTERED ACTIVE LOW OUTPUTS CLOCK tPR MAX = 1 µs t WL 10% 90% t PR VCC tS Document #: 38-03026 Rev. *B Page 7 of 14 USE ULTRA37000TM FOR ALL NEW DESIGNS Functional Logic Diagram for PALCE20V8 PIN NUMBERS DIP (PLCC) PACKAGE PALCE20V8 1 (2) 0 4 8 12 16 20 24 28 32 32 PTD PIN NUMBERS DIP (PLCC)PACKAGE 1 0 CG0 0 2 (3) 23 (27) MC7 CL1=2560 CL0=2632 22 (26) 280 3 (4) 320 MC6 CL1=2561 CL0=2633 21 (25) 600 4 (5) 640 MC5 CL1=2562 CL0=2634 20 (24) 920 5 (6) 960 MC4 CL1=2563 CL0=2635 19 (23) 1240 6 (7) 1280 MC3 CL1=2564 CL0=2636 18 (21) 1560 7 (9) 1600 MC2 CL1=2565 CL0=2637 17 (20) 1880 8 (10) 1920 MC1 CL1=2566 CL0=2638 16 (19) 2200 9 (11) 2240 MC0 CL1=2567 CL0=2639 15 (18) 2520 10 (12) 11 (13) CG0 0 1 14 (17) 13 (16) ELECTRONIC SIGNATURE ROW 2568 BYTE7 2569 . . . BYTE6 . . . . . . 2630 . . . BYTE1 2631 BYTE0 CG0=2704 CG1=2705 MSB LSB Document #: 38-03026 Rev. *B Page 8 of 14 USE ULTRA37000TM FOR ALL NEW DESIGNS Ordering Information for PALCE20V8 ICC (mA) 115 115 115 tPD (ns) 5 7.5 10 tS (ns) 3 7 10 tCO (ns) 4 5 7 Ordering Code PALCE20V8−5JC PALCE20V8−7JC PALCE20V8−7PC PALCE20V8−10JC PALCE20V8−10PC PALCE20V8−10QC 130 10 10 10 PALCE20V8−10JI PALCE20V8−10PI PALCE20V8−10DMB PALCE20V8−10LMB 90 15 12 10 PALCE20V8−15JC PALCE20V8−15PC PALCE20V8−15QC 130 15 12 12 PALCE20V8−15JI PALCE20V8−15PI PALCE20V8−15QI PALCE20V8−15DMB PALCE20V8−15LMB 90 25 15 12 PALCE20V8−25JC PALCE20V8−25PC PALCE20V8−25QC 130 25 20 20 PALCE20V8−25JI PALCE20V8−25PI PALCE20V8−25QI PALCE20V8−25DMB PALCE20V8−25LMB Shaded areas contain preliminary information. PALCE20V8 Package Name J64 J64 P13 J64 P13 Q13 J64 P13 D14 L64 J64 P13 Q13 J64 P13 Q13 D14 L64 J64 P13 Q13 J64 P13 Q13 D14 L64 Package Type 28-Lead Plastic Leaded Chip Carrier 28-Lead Plastic Leaded Chip Carrier 24-Lead (300-Mil) Molded DIP 28-Lead Plastic Leaded Chip Carrier 24-Lead (300-Mil) Molded DIP 24-Lead Quarter-Size Outline 28-Lead Plastic Leaded Chip Carrier 24-Lead (300-Mil) Molded DIP 24-Lead (300-Mil) CerDIP 28-Pin Square Leadless Chip Carrier 28-Lead Plastic Leaded Chip Carrier 24-Lead (300-Mil) Molded DIP 24-Lead Quarter-Size Outline 28-Lead Plastic Leaded Chip Carrier 24-Lead (300-Mil) Molded DIP 24-Lead Quarter-Size Outline 24-Lead (300-Mil) CerDIP 28-Pin Square Leadless Chip Carrier 28-Lead Plastic Leaded Chip Carrier 24-Lead (300-Mil) Molded DIP 24-Lead Quarter-Size Outline 28-Lead Plastic Leaded Chip Carrier 24-Lead (300-Mil) Molded DIP 24-Lead Quarter-Size Outline 24-Lead (300-Mil) CerDIP 28-Pin Square Leadless Chip Carrier Operating Range Commercial Commercial Industrial Military Commercial Industrial Military Commercial Industrial Military Ordering Information for PALCE20V8L ICC (mA) 55 tPD (ns) 15 tS (ns) 12 tCO (ns) 10 Ordering Code PALCE20V8L−15JC PALCE20V8L−15PC PALCE20V8L−15QC 65 15 12 12 PALCE20V8L−15JI PALCE20V8L−15PI PALCE20V8L−15QI PALCE20V8L−15DMB PALCE20V8L−15LMB 55 25 15 12 PALCE20V8L−25JC PALCE20V8L−25PC PALCE20V8L−25QC Package Name J64 P13 Q13 J64 P13 Q13 D14 L64 J64 P13 Q13 Package Type 28-Lead Plastic Leaded Chip Carrier 24-Lead (300-Mil) Molded DIP 24-Lead Quarter-Size Outline 28-Lead Plastic Leaded Chip Carrier 24-Lead (300-Mil) Molded DIP 24-Lead Quarter-Size Outline 24-Lead (300-Mil) CerDIP 28-Pin Square Leadless Chip Carrier 28-Lead Plastic Leaded Chip Carrier 24-Lead (300-Mil) Molded DIP 24-Lead Quarter-Size Outline Commercial Military Industrial Operating Range Commercial Document #: 38-03026 Rev. *B Page 9 of 14 USE ULTRA37000TM FOR ALL NEW DESIGNS Ordering Information for PALCE20V8L (continued) ICC (mA) 65 tPD (ns) 25 tS (ns) 20 tCO (ns) 20 Ordering Code PALCE20V8L−25JI PALCE20V8L−25PI PALCE20V8L−25QI PALCE20V8L−25DMB PALCE20V8L−25LMB Package Name J64 P13 Q13 D14 L64 Package Type PALCE20V8 Operating Range Industrial 28-Lead Plastic Leaded Chip Carrier 24-Lead (300-Mil) Molded DIP 24-Lead Quarter-Size Outline 24-Lead (300-Mil) CerDIP 28-Pin Square Leadless Chip Carrier Military Document #: 38-03026 Rev. *B Page 10 of 14 USE ULTRA37000TM FOR ALL NEW DESIGNS MILITARY SPECIFICATIONS Group Subgroup Testing DC Characteristics Parameter VOH VOL VIH VIL IIX IOZ ICC 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 Subgroups PALCE20V8 Switching Characteristics Parameter tPD tCO tS tH Subgroups 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 Package Diagrams 24-Lead (300-Mil) CerDIP D14 MIL-STD-1835 D- 9 Config.A 51-80031-** Document #: 38-03026 Rev. *B Page 11 of 14 USE ULTRA37000TM FOR ALL NEW DESIGNS Package Diagrams (continued) 28-Lead Plastic Leaded Chip Carrier J64 PALCE20V8 51-85001-*A 28-Square Leadless Chip Carrier L64 MIL-STD-1835 C-4 51-80051-** Document #: 38-03026 Rev. *B Page 12 of 14 USE ULTRA37000TM FOR ALL NEW DESIGNS Package Diagrams (continued) 24-Lead (300-Mil) PDIP P13 PALCE20V8 51-85013-*B 24-Lead Quarter Size Outline Q13 51-85055-B Ultra37000 is a trademark of Cypress Semiconductor Corporation. PAL is a registered trademark of Advanced Micro Devices, Inc. All products and company names mentioned in this document may be the trademarks of their respective holders. Document #: 38-03026 Rev. *B Page 13 of 14 © Cypress Semiconductor Corporation, 2004. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges. USE ULTRA37000TM FOR ALL NEW DESIGNS Document History Page Document Title: PALCE20V8 Flash-Erasable Reprogrammable CMOS PAL® Device Document Number: 38-03026 REV. ** *A *B ECN NO. 106371 122231 213375 Issue Date 07/11/01 12/28/02 See ECN Orig. of Change SZV RBI FSG Description of Change Changed from Spec Number: 38-00367 to 38-03026 PALCE20V8 Added power-up requirements to Operating Range Information Added note to title page: “Use Ultra37000 For All New Designs” Document #: 38-03026 Rev. *B Page 14 of 14