“Spansion, Inc.” and “Cypress Semiconductor Corp.” have merged together to deliver high-performance, high-quality solutions at
the heart of today's most advanced embedded systems, from automotive, industrial and networking platforms to highly interactive
consumer and mobile devices. The new company “Cypress Semiconductor Corp.” will continue to offer “Spansion, Inc.” products
to new and existing customers.
CONTINUITY OF SPECIFICATIONS
There is no change to this document as a result of offering the device as a Cypress product. Any changes that have been made
are the result of normal document improvements and are noted in the document history page, where supported. Future revisions
will occur when appropriate, and changes will be noted in a document history page.
CONTINUITY OF ORDERING PART NUMBERS
Cypress continues to support existing part numbers. To order these products, please use only the Ordering Part Numbers listed in
this document.
FOR MORE INFORMATION
Please visit our website at www.cypress.com or contact your local sales office for additional information about Cypress products
and services.
OUR CUSTOMERS
Cypress is for true innovators – in companies both large and small.
Our customers are smart, aggressive, out-of-the-box thinkers who design and develop game-changing products that revolutionize
their industries or create new industries with products and solutions that nobody ever thought of before.
ABOUT CYPRESS
Founded in 1982, Cypress is the leader in advanced embedded system solutions for the world’s most innovative automotive,
industrial, home automation and appliances, consumer electronics and medical products. Cypress’s programmable systems-onchip, general-purpose microcontrollers, analog ICs, wireless and USB-based connectivity solutions and reliable, high-performance
memories help engineers design differentiated products and get them to market first.
Cypress is committed to providing customers with the best support and engineering resources on the planet enabling innovators
and out-of-the-box thinkers to disrupt markets and create new product categories in record time. To learn more, go to
www.cypress.com.
Cypress Semiconductor Corporation
Document Number: 002-00719 Rev. *K
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised November 09, 2017
S25FL216K
16-Mbit 3.0 V Serial Flash Memory
with Uniform 4 kB Sectors
Distinctive Features
Single power supply operation
– Full voltage range: 2.7 to 3.6V
Flexible Architecture with 4 kB Sectors
– Sector Erase (4 kB)
– Block Erase (64 kB)
– Page Program up to 256 bytes
– 100k erase/program cycles typical
– 20-year data retention typical
16-Mbit Serial Flash
– 16-Mbit/2048 kbyte/9192 pages
– 256 bytes per programmable page
– Uniform 4-kbyte Sectors/64-kbyte Blocks
Standard and Dual
– Standard SPI: SCK, CS#, SI, SO, WP#, HOLD#
– Dual SPI: SCK, CS#, SI/IO0, SO, WP#, HOLD#
– Fast Read Dual Output instruction
– Auto-increment Read capability
Software and Hardware Write Protection
– Write Protect all or portion of memory via software
– Enable/Disable protection with WP# pin
High Performance
– FAST READ (Serial): 65 MHz clock rate
– DUAL OUTPUT READ: 65 MHz clock rate
High Performance Program/Erase Speed
– Page program time: 1.6 ms typical
– Sector erase time (4 kB): 45 ms typical
– Block erase time (64 kB): 450 ms typical
– Chip erase time: 12 seconds typical
Low Power Consumption
– 12 mA typical active current
– 15 µA typical standby current
Package Options
– 8-pin SOIC 150/208-mil
– All Pb-free packages are RoHS compliant
General Description
The S25FL216K device is a 16-Mbit, 2048-kbyte Serial Flash memory, with advanced write protection mechanisms. The
S25FL216K supports the standard Serial Peripheral Interface (SPI), and a high performance Dual output using SPI pins: Serial
Clock, Chip Select, Serial SI/IO0, SO, WP#, and HOLD#. SPI clock frequencies of up to 65 MHz are supported.
The S25FL216K array is organized into 8,192 programmable pages of 256 bytes each. Up to 256 bytes can be programmed at a
time. Pages can be erased in groups of 16 (4-kB Sector Erase), groups of 256 (64-kB Block Erase) or the entire chip (Chip Erase).
The S25FL216K has 512 erasable sectors and 32 erasable blocks. The small 4 kB sectors allow for greater flexibility in applications
that require data and parameter storage.
A Hold pin, Write Protect Pin and programmable write protection provide further control flexibility. Additionally, the S25FL216K
device supports JEDEC standard manufacturer and device identification.
Cypress Semiconductor Corporation
Document Number: 002-00719 Rev. *K
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised November 09, 2017
S25FL216K
Contents
Distinctive Features ............................................................. 2
General Description ............................................................. 2
1.
Block Diagram.............................................................. 4
2.
Connection Diagrams.................................................. 4
3.
Signal Descriptions ..................................................... 5
4.
4.1
Ordering Information ................................................... 6
Valid Combinations ........................................................ 6
5.
Memory Organizations ................................................ 7
6.
6.1
6.2
6.3
6.4
Functional Description ................................................
SPI Modes .....................................................................
Dual Output SPI .............................................................
Hold Function.................................................................
Status Register ..............................................................
7.
7.1
7.2
7.3
7.4
Write Protection ......................................................... 10
Page Programming ...................................................... 11
Sector Erase, Block Erase, and Chip Erase ................ 11
Polling During a Write, Program, or Erase Cycle......... 11
Active Power, Stand-by Power, and Deep Power-Down
Modes .......................................................................... 11
8.
8.1
8.2
Commands ................................................................. 11
Write Enable (06h) ....................................................... 12
Write Disable (04h) ...................................................... 13
Document Number: 002-00719 Rev. *K
8
8
8
8
9
8.3
8.4
8.5
8.6
8.7
8.8
8.9
8.10
8.11
8.12
8.13
8.14
8.15
Read Status Register (05h) .......................................... 13
Write Status Register (01h)........................................... 14
Read Data (03h) ........................................................... 15
Fast Read (0Bh) ........................................................... 15
Fast Read Dual Output (3Bh) ....................................... 16
Page Program (PP) (02h) ............................................. 17
Sector Erase (SE) (20h)................................................ 18
Block Erase (BE) (D8h)................................................. 19
Chip Erase (CE) (C7h).................................................. 19
Deep Power-down (DP) (B9h) ...................................... 20
Release Deep Power-down / Device ID (ABh) ............. 21
Read Manufacturer / Device ID (90h) ........................... 22
Read Identification (RDID) (9Fh) .................................. 23
9.
9.1
9.2
9.3
9.4
9.5
9.6
Electrical Specifications............................................. 25
Power-up Timing........................................................... 25
Absolute Maximum Ratings .......................................... 26
Recommended Operating Ranges ............................... 26
DC Characteristics ........................................................ 27
AC Measurement Conditions ........................................ 27
AC Characteristics ........................................................ 28
10. Package Material......................................................... 31
10.1 8-Pin SOIC 150-mil Package (SOA 008) ...................... 31
10.2 8-Pin SOIC 208-mil Package (SOC 008)...................... 32
11.
Revision History.......................................................... 33
Page 3 of 35
S25FL216K
1. Block Diagram
Flash
M em ory
X -Decoder
Address
Buffers
and
Latches
Y- Decoder
I/O Buffers
and Data
Latches
Control Logic
Serial Interface
CS #
SCK
SI/IO0
SO
W P#
HO LD #
2. Connection Diagrams
Figure 2.1 8-pin SOIC (150/208 mil)
Document Number: 002-00719 Rev. *K
CS#
1
8
VCC
SO
2
7
HOLD#
WP#
3
6
SCK
GND
4
5
SI/IO0
Page 4 of 35
S25FL216K
3. Signal Descriptions
Serial Data Input / Output (SI/IO0)
The SPI Serial Data Input/Output (SI/IO0) pin provides a means for instructions, addresses and data to be serially written to (shifted
into) the device. Data is latched on the rising edge of the Serial Clock (SCK) input pin. The SI/IO0 pin is also used as an output pin
when the Fast Read Dual Output instruction is executed.
Serial Data Output (SO)
The SPI Serial Data Output (SO) pin provides a means for data and status to be serially read from (shifted out of) the device. Data is
shifted out on the falling edge of the Serial Clock (SCK) input pin.
Serial Clock (SCK)
The SPI Serial Clock Input (SCK) pin provides the timing for serial input and output operations. See SPI Modes on page 8.
Chip Select (CS#)
The SPI Chip Select (CS#) pin enables and disables device operation. When CS# is high the device is deselected and the Serial
Data Output pins are at high impedance.
When deselected, the device’s power consumption will be at standby levels unless an internal erase, program or status register
cycle is in progress. When CS# is brought low the device will be selected, power consumption will increase to active levels and
instructions can be written to and data read from the device. After power-up, CS# must transition from high to low before a new
instruction will be accepted.
HOLD (HOLD#)
The HOLD# pin allows the device to be paused while it is actively selected. When HOLD# is brought low, while CS# is low, the SO
pin will be at high impedance and signals on the SI and SCK pins will be ignored (don’t care). The HOLD# function can be useful
when multiple devices are sharing the same SPI signals.
Write Protect (WP#)
The Write Protect (WP#) pin can be used to prevent the Status Register from being written. Used in conjunction with the Status
Register’s Block Protect (BP0, BP1 and BP2, BP3) bits and Status Register Protect (SRP) bits, a portion or the entire memory array
can be hardware protected.
Table 3.1 Pin Descriptions
Symbol
Pin Name
SCK
Serial Clock Input
SI/IO0
Serial Data Input / Output (1)
SO
Serial Data Output
CS#
Chip Enable
WP#
Write Protect
HOLD#
Hold Input
VCC
Supply Voltage (2.7-3.6V)
GND
Ground
Note:
1. SI/IO0 output is used for Dual Output Read instruction.
Document Number: 002-00719 Rev. *K
Page 5 of 35
S25FL216K
4.
Ordering Information
The ordering part number is formed by a valid combination of the following:
S25FL
216
K
0P
M
F
I
01
1
Packing Type
0 = Tray
1 = Tube
3 = 13” Tape and Reel
Model Number (Additional Ordering Options)
04 = 8-pin SO package (150 mil)
01 = 8-pin SO package (208 mil)
Temperature Range
I = Industrial (–40°C to +85°C)
Package Materials
F = Lead (Pb)-free
Package Type
M = 8-pin SO package
Speed
0P = 65 MHz
Device Technology
K = 0.09 µm process technology
Density
216= 16 Mbit
Device Family
S25FL
Spansion Memory 3.0 Volt-Only, Serial Peripheral Interface (SPI) Flash Memory
4.1
Valid Combinations
Table 4.1 lists the valid combinations configurations planned to be supported in volume for this device.
Table 4.1 S25FL216K Valid Combinations
S25FL216K Valid Combinations
Base Ordering
Part Number
Speed Option
Package and
Temperature
Model
Number
Packing Type
Package Marking
S25FL216K
0P
MFI
01, 04
0, 1, 3
FL216KIF
Document Number: 002-00719 Rev. *K
Page 6 of 35
S25FL216K
5.
Memory Organizations
The memory is organized as:
2,097,152 bytes
Uniform Sector Architecture
– 32 blocks of 64 kB
– 512 sectors of 4 kB
8,192 pages (256 bytes each)
Each page can be individually programmed (bits are programmed from 1 to 0). The device is Sector, Block or Chip Erasable but not
Page Erasable.
Figure 5.1 Memory Organization
xxFF00h
.
Sector 15 (4 kB)
xxF000h
xxEF00h
Sector 14 (4 kB)
xxE000h
1FFF00h
.
.
xxF0FFh
xxEFFFh
1F0000h
1FFFFFh
Block 31 (64 kB)
.
xxE0FFh
08FF00h
.
08FFFFh
Block 8 (64 kB)
…
0800FFh
07FF00h
07FFFFh
Block 7 (64 kB)
070000h
xx1F00h
Sector 1 (4 kB)
Document Number: 002-00719 Rev. *K
Sector 0 (4 kB)
...
xx0000h
.
0700FFh
xx1FFFh
xx1000h
xx0F00h
.
.
080000h
.
.
.
1F0FFFh
...
.
xxFFFFh
.
xx10FFh
xx0FFFh
00FF00h
.
.
xx00FFh
000000h
00FFFFh
Block 0 (64 kB)
.
0000FFh
Page 7 of 35
S25FL216K
6.
Functional Description
6.1
SPI Modes
The S25FL216K device can be driven by an embedded microcontroller (bus master) in either of the two following clocking modes.
Mode 0 with Clock Polarity (CPOL) = 0 and, Clock Phase (CPHA) = 0
Mode 3 with CPOL = 1 and, CPHA = 1
For these two modes, input data into the device is always latched in on the rising edge of the SCK signal and the output data is
always available from the falling edge of the SCK clock signal. The difference between the two modes is the clock polarity when the
bus master is in standby mode and not transferring any data.
SCK will stay at logic low state with CPOL = 0, CPHA = 0
SCK will stay at logic high state with CPOL = 1, CPHA = 1
Figure 6.1 SPI Modes
CS #
SCK
SI/IO0
M ode3
M ode 3
M ode0
M ode 0
B it7
B it6
B it5
B it4
B it3
B it2
B it1
B it0
D ON T C AR E
M SB
SO
H ig h Im p e d a n ce
B it7
B it6
B it5
B it4
B it3
B it2
B it1
B it0
M SB
6.2
Dual Output SPI
The S25FL216K supports Dual Output Operation when using the “Fast Read with Dual Output” (3B hex) command. This feature
allows data to be transferred from the Serial Flash at twice the rate possible with the standard SPI. This command can be used to
quickly download code from Flash to RAM upon Power-up (Code-shadowing) or for applications that cache code-segments to RAM
for execution.
The Dual Output feature simply allows the SPI data input pin (SI) to also serve as an output during this command. All other
operations use the standard SPI interface with single signal. The host keeps CS# low and HOLD# high. The Write Protect (WP#)
signal is ignored. The memory drives data on the SI/IO0 and SO signals during the dual output cycles. The next interface state
continues to be Dual Output Cycle until the host returns CS# to high ending the command.
6.3
Hold Function
The Hold (HOLD#) signal is used to pause any serial communications with the S25FL216K device without deselecting the device or
stopping the serial clock. To enter the Hold condition, the device must be selected by driving the CS# input to the logic low state. It is
recommended that the user keep the CS# input low state during the entire duration of the Hold condition. This is to ensure that the
state of the interface logic remains unchanged from the moment of entering the Hold condition. If the CS# input is driven to the logic
high state while the device is in the Hold condition, the interface logic of the device will be reset. To restart communication with the
device, it is necessary to drive HOLD# to the logic high state while driving the CS# signal into the logic low state. This prevents the
device from going back into the Hold condition.
The Hold condition starts on the falling edge of the Hold (HOLD#) signal, provided that this coincides with SCK being at the logic low
state. If the falling edge does not coincide with the SCK signal being at the logic low state, the Hold condition starts whenever the
SCK signal reaches the logic low state. Taking the HOLD# signal to the logic low state does not terminate any Write, Program or
Erase operation that is currently in progress.
Document Number: 002-00719 Rev. *K
Page 8 of 35
S25FL216K
During the Hold condition, SO is in high impedance and both the SI and SCK input are Don't Care. The Hold condition ends on the
rising edge of the Hold (HOLD#) signal, provided that this coincides with the SCK signal being at the logic low state. If the rising
edge does not coincide with the SCK signal being at the logic low state, the Hold condition ends whenever the SCK signal reaches
the logic low state.
Figure 6.2 Hold Condition Waveform
SCK
HO LD #
A ctive
6.4
H o ld
A ctive
H o ld
A ctive
Status Register
The Status Register contains a number of status and control bits that can be read or set (as appropriate) by specific instructions
Table 6.1 Status Register Bit Locations
R7
R6
R5
R4
R3
R2
R1
R0
SRP
REV
BP3
BP2
BP1
BP0
WEL
WIP
WIP (Write In Progress) is a read only bit in the status register (R0) which indicates whether the device is performing a
program, write, erase operation, or any other operation, during which a new operation command will be ignored. When the
WIP bit is set to 1, the device is busy performing an operation. When the bit is cleared to 0, no operation is in progress.
Write Enable Latch (WEL) is a read only bit in the status register (R1) that must be set to 1 to enable program, write, or
erase operations as a means to provide protection against inadvertent changes to memory or register values. The Write
Enable (WREN) command execution sets the Write Enable Latch to a 1 to allow any program, erase, or write commands to
execute afterwards. The Write Disable (WRDI) command can be used to set the Write Enable Latch to a 0 to prevent all
program, erase, and write commands from execution. The WEL bit is cleared to 0 at the end of any successful program,
write, or erase operation. After a power down/power up sequence, hardware reset, or software reset, the Write Enable
Latch is set to a 0.
Block Protect Bits (BP3, BP2, BP1, BP0) are non-volatile read/write bits in the status register (R5, R4, R3, and R2) that
define the main flash array area to be software protected against program and erase commands. When one or more of the
BP bits is set to 1, the relevant memory area is protected against program and erase. The Chip Erase (CE) command can
be executed only when the BP bits are cleared to 0’s. See Table 7.1 on page 10 for a description of how the BP bit values
select the memory array area protected. The factory default setting for all the BP bits is 0, which implies that none of array
is protected.
Reserved Bits (REV), Status register bit location R6 is reserved for future use. Current devices will read 0 for this bit
location. It is recommended to mask out the reserved bit when testing the Status Register. Doing this will ensure
compatibility with future devices.
The Status Register Protect (SRP) bit is a non-volatile read/write bit in status register (R7) that can be used in conjunction
with the Write Protect (WP#) pin to disable writes to status register. When the SRP bit is set to a 0 state (factory default) the
WP# pin has no control over status register. When the SRP pin is set to a 1, the Write Status Register instruction is locked
out while the WP# pin is low. When the WP# pin is high the Write Status Register instruction is allowed.
Document Number: 002-00719 Rev. *K
Page 9 of 35
S25FL216K
7. Write Protection
Some basic protection against unintended changes to stored data is provided and controlled purely by the hardware design. These
protection mechanisms in the S25FL216K device are described below:
Power-On Reset and an internal timer (tPUW) can provide protection against inadvertent changes while the power supply is
outside the operating specification.
Program, Erase and Write Status Register instructions are checked that they consist of a number of clock pulses that is a
multiple of eight, before they are accepted for execution.
All instructions that modify data must be preceded by a Write Enable (WREN) instruction to set the Write Enable Latch
(WEL) bit. This bit is returned to its reset state by the following events:
– Power-up
– Write Disable (WRDI) instruction completion or Write Status Register (WRSR) instruction completion or Page Program
(PP) instruction completion or Sector Erase (SE) instruction completion or Block Erase (BE) instruction completion or Chip
Erase (CE) instruction completion
The Block Protect (BP3, BP2, BP1, and BP0) bits allow part of the memory to be configured as read-only. This is the
Software Protected Mode (SPM).
The Write Protect (WP#) signal allows the Block Protect (BP3, BP2, BP1, BP0) bits and Status Register Protect (SRP) bit to
be protected. This is the Hardware Protected Mode (HPM).
In addition to the low power consumption feature, the Deep Power-down mode offers extra software protection from
inadvertent Write, Program and Erase instructions, as all instructions are ignored except one particular instruction (the
Release from Deep Power-down instruction).
Table 7.1 Protected Area Sizes Block Organization — S25FL216K
Status Bit
Protect Blocks
BP3
BP2
BP1
BP0
0
0
0
0
0 (None)
0
0
0
1
1 (1 block, block 31th)
0
0
1
0
2 (2 blocks, block 30th~31th)
0
0
1
1
3 (4 blocks, block 28th~31th)
0
1
0
0
4 (8 blocks, block 24th~31th)
0
1
0
1
5 (16 blocks, block 16th~31th)
0
1
1
0
6 (32 blocks, all)
0
1
1
1
7 (32 blocks, all)
1
0
0
0
8 (32 blocks, all)
1
0
0
1
9 (32 blocks, all)
1
0
1
0
10 (16 blocks, block 0th~15th)
1
0
1
1
11 (24 blocks, block 0th~23th)
1
1
0
0
12 (28 blocks, block 0th~27th)
1
1
0
1
13 (30 blocks, block 0th~29th)
1
1
1
0
14 (31 blocks, block 0th~30th)
1
1
1
1
15 (32 blocks, all)
Document Number: 002-00719 Rev. *K
Page 10 of 35
S25FL216K
7.1
Page Programming
To program one data byte, two instructions are required: Write Enable (WREN), which is one byte, and a Page Program (PP)
sequence, which consists of four bytes plus data. This is followed by the internal Program cycle (of duration tPP). To spread this
overhead, the Page Program (PP) instruction allows up to 256 bytes to be programmed at a time (changing bits from 1 to 0),
provided that they lie in consecutive addresses on the same page of memory.
7.2
Sector Erase, Block Erase, and Chip Erase
The Page Program (PP) instruction allows bits to be reset from 1 to 0. Before this can be applied, the bytes of memory need to have
been erased to all 1s (FFh). This can be achieved a sector at a time, using the Sector Erase (SE) instruction, a block at a time using
the Block Erase (BE) instruction or throughout the entire memory, using the Chip Erase (CE) instruction. This starts an internal
Erase cycle (of duration tSE, tBE, or tCE). The Erase instruction must be preceded by a Write Enable (WREN) instruction.
7.3
Polling During a Write, Program, or Erase Cycle
A further improvement in the time to Write Status Register (WRSR), Program (PP) or Erase (SE, BE, or CE) can be achieved by not
waiting for the worst case delay (tW, tPP, tSE, tBE, or tCE). The Write In Progress (WIP) bit is provided in the Status Register so that
the application program can monitor its value, polling it to establish when the previous Write cycle, Program cycle or Erase cycle is
complete.
7.4
Active Power, Stand-by Power, and Deep Power-Down Modes
When Chip Select (CS#) is Low, the device is enabled, and in the Active Power mode. When Chip Select (CS#) is High, the device
is disabled, but could remain in the Active Power mode until all internal cycles have completed (Program, Erase, Write Status
Register). The device then goes into the Standby Power mode. The device consumption drops to ICC1.
The Deep Power-down mode is entered when the specific instruction (the Enter Deep Power-down Mode (DP) instruction) is
executed, with the device consumption at ICC2. The device remains in this mode until another specific instruction (the Release from
Deep Power-down Mode and Read Device ID (RDI) instruction) is executed.
All other instructions are ignored while the device is in the Deep Power-down mode. This can be used as an extra software
protection mechanism, when the device is not in active use, to protect the device from inadvertent Write, Program or Erase
instructions.
8. Commands
The command set of the S25FL216K consists of fifteen basic instructions that are fully controlled through the SPI bus (see
Table 8.1). The host system must shift all commands, addresses, and data in and out of the device, beginning with the most
significant bit. On the first rising edge of SCK after CS# is driven low, the device accepts the one-byte command on SI (all
commands are one byte long), most significant bit first. Each successive bit is latched on the rising edge of SCK.
Every command sequence begins with a one-byte command code. The command may be followed by address, data, both, or
nothing, depending on the command. CS# must be driven high after the last bit of the command sequence has been written. All
commands that write, program or erase require that CS# be driven high at a byte boundary, otherwise the command is not executed.
Since a byte is composed of eight bits, CS# must therefore be driven high when the number of clock pulses after CS# is driven low
is an exact multiple of eight. The device ignores any attempt to access the memory array during a Write Registers, program, or erase
operation, and continues the operation uninterrupted.
Table 8.1 Command Set (Sheet 1 of 2)
Command
Name
Byte1 Code
Write Enable
06h
write Disable
04h
Read Status
Register
05h
Byte2
(S7-S0) (1)
Document Number: 002-00719 Rev. *K
Byte3
Byte4
Byte5
Byte6
N-bytes
(Note 2)
Page 11 of 35
S25FL216K
Table 8.1 Command Set (Sheet 2 of 2)
Command
Name
Byte1 Code
Byte2
Write Status
Register
01h
S7-S0
Read Data
03h
A23-A16
Byte3
Byte4
Byte5
Byte6
A15-A8
A7-A0
(D7-D0)
(Next byte)
continuous
(D7-D0)
(Next byte)
continuous
Fast Read
0Bh
A23-A16
A15-A8
A7-A0
dummy
Fast Read
Dual Output
3Bh
A23-A16
A15-A8
A7-A0
dummy
Page Program
02h
A23-A16
A15-A8
A7-A0
(D7-D0)
Block Erase
(64 kB)
D8h
A23-A16
A15-A8
A7-A0
Sector Erase
(4 kB)
20h
A23-A16
A15-A8
A7-A0
Chip Erase
C7h/60h
Power-down
B9h
Release
Power-down /
Device ID
ABh
dummy
dummy
dummy
(ID7-ID0) (4)
Manufacturer /
Device ID (3)
90h
dummy
dummy
00h
(M7-M0)
JEDEC ID
9Fh
(M7-M0)
manufacturer
(ID15-ID8)
Memory Type
(ID7-ID0)
Capacity
N-bytes
I/O=
(One byte per 4
(D6,D4,D2,D0)
clocks,
O=
continuous)
(D7,D5,D3,D1)
Up to 256
bytes
(Next byte)
(ID7-ID0)
Notes:
1. Data bytes are shifted with Most Significant Bit first. Byte fields with data in parenthesis “( )” indicate data being read from the device on the SO pin.
2. The Status Register contents will repeat continuously until CS# terminates the instruction.
3. See Table 8.2, Manufacturer and Device Identification on page 12 for Device ID information.
4. The Device ID will repeat continuously until CS# terminates the instruction.
Table 8.2 Manufacturer and Device Identification
OP Code
(M7-M0)
(ID15-ID0)
ABh
8.1
(ID7-ID0)
14h
90h
01h
9Fh
01h
14h
4015h
Write Enable (06h)
The Write Enable command (Figure 8.1) sets the Write Enable Latch (WEL) bit in the Status Register to a 1, which enables the
device to accept a Write Status Register, program, or erase command.
The WEL bit must be set prior to every Page Program, Sector Erase, Block Erase, Chip Erase, and Write Status Register command.
The host system must first drive CS# low, write the WREN command, and then drive CS# high.
Document Number: 002-00719 Rev. *K
Page 12 of 35
S25FL216K
Figure 8.1 Write Enable Command Sequence
CS
M o d e3
SCK
0
1
3
2
4
5
6
7
M o d e3
M o d e0
M o d e0
Ins truc tion (06 H)
SI/IO0
H igh Im pedanc e
SO
8.2
Write Disable (04h)
The Write Disable command (Figure 8.2) resets the Write Enable Latch (WEL) bit to a 0, which disables the device from accepting a
write, program or erase command. The host system must first drive CS# low, write the WRDI command, and then drive CS# high.
The WEL bit is automatically reset after Power-up and upon completion of the Write Status Register, Page Program, Sector Erase,
Block Erase, and Chip Erase commands.
Figure 8.2 Write Disable Command Sequence
CS
M o d e3
SCK
0
1
2
3
4
5
6
7
M o d e3
M o d e0
M o d e0
Ins truc tion (04 H)
SI/IO0
SO
8.3
H igh Im pedanc e
Read Status Register (05h)
The Read Status Register (RDSR) command outputs the state of the Status Register bits. The RDSR command may be written at
any time, even while a program, erase, or Write Registers operation is in progress. The host system should check the Write In
Progress (WIP) bit before sending a new command to the device if an operation is already in progress. Figure 8.3 shows the RDSR
command sequence, which also shows that it is possible to read the Status Register continuously until CS# is driven high. (See
Section 6.4, Status Register on page 9).
Document Number: 002-00719 Rev. *K
Page 13 of 35
S25FL216K
Figure 8.3 Read Status Register Command Sequence
CS #
SCK
Mode3
Mode0
0
1
2
3
4
5
6
7
8
9
10
11
12 13
14 15
16
17 18
19 20
21
22 23
Instruction (05 H )
SI/IO0
Status Register O ut
Status Register O ut
SO
High Im pedance
7
*
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
*
*=M SB
8.4
Write Status Register (01h)
The Write Status Register command allows the Status Register to be written. A Write Enable command must previously have been
executed for the device to accept the Write Status Register command (Status Register bit WEL must equal 1). Once write enabled,
the command is entered by driving CS# low, sending the instruction code “01h”, and then writing the status register data byte as
illustrated in Figure 8.4. The Status Register bits are shown in Table 6.1 on page 9 and described in Section 6.4, Status Register
on page 9.
Only non-volatile Status Register bits SRP, BP3, BP2, BP1, and BP0 (bits 7, 5, 4, 3, and 2) can be written to. All other Status
Register bit locations are read-only and will not be affected by the Write Status Register command.
The CS# chip select input pin must be driven to the logic high state after the eighth bit of data has been latched in. If not, the Write
Status Register command is not executed. As soon as the CS# chip select input pin is driven to the logic high state, the self-timed
Write Status Register cycle is initiated. While the Write Status Register cycle is in progress, the Status Register may still be read to
check the value of the Write In Progress (WIP) bit. The Write In Progress (WIP) bit is a 1 during the self-timed Write Status Register
cycle, and is a 0 when it is completed. When the Write Status Register cycle is completed, the Write Enable Latch (WEL) is set to a
0.
The Write Status Register command allows the Block Protect bits (BP3, BP2, BP1, and BP0) to be set for protecting all, a portion, or
none of the memory from erase and program commands. Protected areas become read-only (see Table 7.1 on page 10). The Write
Status Register command also allows the Status Register Protect bit (SRP) to be set. This bit is used in conjunction with the Write
Protect (WP#) pin to disable writes to the status register. When the SRP bit is set to a 0 state (factory default) the WP# pin has no
control over the status register. When the SRP pin is set to a 1, the Write Status Register command is locked out while the WP# pin
is low. When the WP# pin is high the Write Status Register command is allowed.
Document Number: 002-00719 Rev. *K
Page 14 of 35
S25FL216K
Figure 8.4 Write Status Register Command Sequence
CS #
0
Mode3
SCK M o d e 0
1
2
3
4
5
6
7
8
9
10 11
12 13
14 15
5
3
1
Mode3
Mode0
In stru ctio n ( 0 1H )
SI/IO0
7
6
4
2
0
*
High Im pedance
SO
*= M SB
8.5
Read Data (03h)
The Read Data command allows one more data bytes to be sequentially read from the memory. The command is initiated by driving
the CS# pin low and then shifting the instruction code “03h” followed by a 24-bit address (A23-A0) into the SI/IO0 pin. The code and
address bits are latched on the rising edge of the SCK pin. After the address is received, the data byte of the addressed memory
location will be shifted out on the SO pin at the falling edge of SCK with most significant bit (MSB) first. The address is automatically
incremented to the next higher address after each byte of data is shifted out allowing for a continuous stream of data. This means
that the entire memory can be accessed with a single command as long as the clock continues. The command is completed by
driving CS# high.
The Read Data command sequence is shown in Figure 8.5. If a Read Data command is issued while an Erase, Program or Write
cycle is in process (WIP=1) the command is ignored and will not have any effects on the current cycle. The Read Data command
allows clock rates from D.C. to a maximum of fR. See AC Characteristics on page 28.
Figure 8.5 Read Data Command Sequence
CS #
SCK
Mode3
Mode0
0
1
2
3
4
5
6
7
8
9
Instruction (03 H)
SI/IO0
*=M SB
8.6
28 29 30
31
32 33
34
35
36
37
38 39
24 -Bit Address
23 22
*
SO
10
High Im pedance
21
3
2
1
0
Data O ut 1
7
6
5
4
3
Data O ut 2
2
1
0
7
*
Fast Read (0Bh)
The Fast Read command is similar to the Read Data command except that it can operate at higher frequency than the traditional
Read Data command. See AC Characteristics on page 28. This is accomplished by adding eight “dummy” clocks after the 24-bit
address as shown in Figure 8.6. The dummy clocks allow the device’s internal circuits additional time for setting up the initial
address. During the dummy clocks the data value on the SI pin is a “don’t care”.
Document Number: 002-00719 Rev. *K
Page 15 of 35
S25FL216K
Figure 8.6 Fast Read Command Sequence
CS#
SCK
M o d e3
M o d e0
0
1
2
3
4
5
7
6
9
8
Instruction (0BH)
28 29 30 31
10
24-Bit Address
23 22 21
SI/IO0
2
3
*
1
0
High Im pedance
SO
CS#
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 51 53 54 55
SCK
Dum m y Clocks
SI/IO0
7
6
5
4
3
2
1
0
Data O ut 1
SO
*=M SB
8.7
7
*
6
5
4
3
Data O ut 1
2
1
0
7
*
6
5
4
3
2
1
0
7
*
Fast Read Dual Output (3Bh)
The Fast Read Dual Output (3Bh) command is similar to the standard Fast Read (0Bh) command except that data is output on two
pins, SO and SI/IO0, instead of just SO. This allows data to be transferred from the S25FL216K at twice the rate of standard SPI
devices. The Fast Read Dual Output command is ideal for quickly downloading code from the SPI flash to RAM upon power-up or
for applications that cache code-segments to RAM for execution.
Similar to the Fast Read command, the Fast Read Dual Output command can operate at higher frequencies than the traditional
Read Data command. See AC Characteristics on page 28. This is accomplished by adding eight “dummy” clocks after the 24-bit
address as shown in Figure 8.7. The dummy clocks allow the device's internal circuits additional time for setting up the initial
address. The input data during the dummy clocks is “don’t care”. However, the SI/IO0 pin should be high-impedance prior to the
falling edge of the first data out clock.
Document Number: 002-00719 Rev. *K
Page 16 of 35
S25FL216K
Figure 8.7 Fast Read Dual Output Command Sequence
CS#
SCK
Mode3
Mode0
0
1
2
3
4
5
6
7
Instruction (3BH )
SI/IO0
28 29 30 31
9 10
8
24-Bit Address
23 22 21
2
3
1
0
*
High Im pedance
SO
CS#
SCK
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 51 53 54 55
SI/IO 0 switches from input to output
Dum m y Clocks
SI/IO0
6
4
2
0
SO
7
5
3
1
*=M SB
8.8
*
D ata out 1
6
4
2 0
6
4
2
0
6
4
2 0
7
5
3
7
5
3
1
7
5
3
*
D ata out 2
1
*
D ata out 3
*
D ata out 4
1
6
7
*
Page Program (PP) (02h)
The Page Program command allows up to 256 bytes of data to be programmed at previously erased to all 1s (FFh) memory
locations. A Write Enable command must be executed before the device will accept the Page Program command (Status Register
bit WEL must equal 1). The command is initiated by driving the CS# pin low then shifting the command code “02h” followed by a 24bit address (A23-A0) and at least one data byte, into the SI/IO0 pin. The CS# pin must be held low for the entire length of the
command while data is being sent to the device. The Page Program command sequence is shown in Figure 8.8.
If an entire 256 byte page is to be programmed, the last address byte (the 8 least significant address bits) should be set to 0. If the
last address byte is not zero, and the number of clocks exceed the remaining page length, the addressing will wrap to the beginning
of the page. In some cases, less than 256 bytes (a partial page) can be programmed without having any effect on other bytes within
the same page. One condition to perform a partial page program is that the number of clocks can not exceed the remaining page
length. If more than 256 bytes are sent to the device the addressing will wrap to the beginning of the page and overwrite previously
sent data.
As with the write and erase commands, the CS# pin must be driven high after the eighth bit of the last byte has been latched. If this
is not done the Page Program command will not be executed. After CS# is driven high, the self-timed Page Program command will
commence for a time duration of tPP. See AC Characteristics on page 28. While the Page Program cycle is in progress, the Read
Status Register command may still be accessed for checking the status of the WIP bit. The WIP bit is a 1 during the Page Program
cycle and becomes a 0 when the cycle is finished and the device is ready to accept other commands again. After the Page Program
cycle has finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Page Program command will not be
executed if the addressed page is protected by the Block Protect (BP3, BP2, BP1, and BP0) bits (see Table 7.1 on page 10).
Document Number: 002-00719 Rev. *K
Page 17 of 35
S25FL216K
Figure 8.8 Page Program Command Sequence
CS #
SCK
0
Mode3
Mode0
1
2
3
4
5
8
9
23
22
7
6
Instruction (02 H )
28
10
29 30 31
32
33 34 35 36
24 -Bit Address
SI/IO0
21
3
37 38
39
2
0
Data Byte 1
2
1
0
*
7
6
5
4
3
1
*
High Im pedance
SO
Data Byte 2
SI/IO0
4
3
2
50
51
52 53 54
55
6
Data Byte 256
5 4
2
3
Data Byte 3
1
*
SO
0
7
6
5
4
*
3
2
1
0
7
2 079
48 49
2 07 8
5
47
46
20 76
6
45
2 07 7
7
43 44
2 07 5
41
2 074
41
2 073
40
SCK
2 07 2
CS #
1
0
Mode3
Mode0
*
High Im pedance
*=M SB
8.9
Sector Erase (SE) (20h)
The Sector Erase command sets all bits in the addressed 4-kB sector to 1 (all bytes are FFh). Before the Sector Erase command
can be accepted by the device, a Write Enable command must be issued and decoded by the device, which sets the Write Enable
Latch bit in the Status Register to enable any write operations. The command is initiated by driving the CS# pin low and shifting the
command code “20h” followed by a 24-bit sector address (A23-A0). The Sector Erase command sequence is shown in Figure 8.9.
The CS# pin must be driven high after the eighth bit of the last byte has been latched. If this is not done the Sector Erase command
will not be executed. After CS# is driven high, the self-timed Sector Erase command will commence for a time duration of tSE.
See AC Characteristics on page 28. While the Sector Erase cycle is in progress, the Read Status Register command may still be
accessed for checking the status of the WIP bit. The WIP bit is a 1 during the Sector Erase cycle and becomes a 0 when the cycle is
finished and the device is ready to accept other commands again. After the Sector Erase cycle has finished the Write Enable Latch
(WEL) bit in the Status Register is cleared to 0. The Sector Erase command will not be executed if the addressed page is protected
by the Block Protect (BP3, BP2, BP1, and BP0) bits (see Table 7.1 on page 10).
Document Number: 002-00719 Rev. *K
Page 18 of 35
S25FL216K
Figure 8.9 Sector Erase Command Sequence
CS#
M ode 3
SCK
0
1
2
3
4
5
6
7
8
9
29
30 31
M ode 3
M ode 0
M ode 0
In stru ctio n ( 2 0H )
2 4 - B it A d d re ss
23
SI/IO0
22
2
1
0
*
High Im pedance
SO
*=M SB
8.10
Block Erase (BE) (D8h)
The Block Erase command sets all bits in the addressed 64-kB block to 1 (all bytes are FFh). Before the BE command can be
accepted by the device, a Write Enable command must be issued and decoded by the device, which sets the Write Enable Latch in
the Status Register to enable any write operations. The command is initiated by driving the CS# pin low and shifting the command
code “D8h” followed a 24-bit block address (A23-A0). The Block Erase command sequence is shown in Figure 8.10.
The CS# pin must be driven high after the eighth bit of the last byte has been latched. If this is not done the Block Erase command
will not be executed. After CS# is driven high, the self-timed Block Erase command will commence for a time duration of tBE. See AC
Characteristics on page 28. While the Block Erase cycle is in progress, the Read Status Register command may still be accessed
for checking the status of the WIP bit. The WIP bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is finished
and the device is ready to accept other commands again. After the Block Erase cycle has finished the Write Enable Latch (WEL) bit
in the Status Register is cleared to 0. The Block Erase command will not be executed if the addressed page is protected by the
Block Protect (BP3, BP2, BP1, and BP0) bits (see Table 7.1 on page 10).
Figure 8.10 Block Erase Command Sequence
CS#
SCK
M ode 3
M ode 0
0
1
2
3
4
5
6
7
8
9
29
30 31
M ode 3
M ode 0
In stru ctio n (D8)
SI/IO0
SO
2 4 - B it A d d re ss
23
22
2
1
0
*
High Im pedance
*=M SB
8.11
Chip Erase (CE) (C7h)
The Chip Erase command sets all bits to 1 (all bytes are FFh) inside the entire flash memory array. Before the CE command can be
accepted by the device, a Write Enable command must be issued and decoded by the device, which sets the Write Enable Latch in
the Status Register to enable any write operations. The command is initiated by driving the CS# pin low and shifting the command
code “C7h”. The Chip Erase command sequence is shown in Figure 8.11.
Document Number: 002-00719 Rev. *K
Page 19 of 35
S25FL216K
The CS# pin must be driven high after the eighth bit has been latched. If this is not done the Chip Erase command will not be
executed. After CS# is driven high, the self-timed Chip Erase command will commence for a time duration of tCE. See AC
Characteristics on page 28. While the Chip Erase cycle is in progress, the Read Status Register command may still be accessed to
check the status of the WIP bit. The WIP bit is a 1 during the Chip Erase cycle and becomes a 0 when finished and the device is
ready to accept other commands again. After the Chip Erase cycle has finished the Write Enable Latch (WEL) bit in the Status
Register is cleared to 0. The Chip Erase command will not be executed if any page is protected by the Block Protect (BP3,BP2, BP1,
and BP0) bits (see Table 7.1 on page 10).
Figure 8.11 Chip Erase Command Sequence
CS #
M o d e3
SCK
0
1
2
3
4
5
6
7
M o d e3
M o d e0
M o d e0
Ins truc tion( C 7H )
SI/IO0
SO
8.12
H igh Im pedanc e
Deep Power-down (DP) (B9h)
The Deep Power-Down (DP) command provides the lowest power consumption mode of the device. It is intended for periods when
the device is not in active use, and ignores all commands except for the Release from Deep Power-Down (RES) command. The
lower power consumption makes the Deep Power-down command especially useful for battery powered applications (See ICC1 and
ICC2 in DC Characteristics on page 27.) The command is initiated by driving the CS# pin low and shifting the command code “B9h”
as shown in Figure 8.12.
The CS# pin must be driven high after the eighth bit has been latched. If this is not done the Deep Power-down command will not be
executed. After CS# is driven high, the power-down state will enter within the time duration of tDP (See AC Characteristics
on page 28.) While in the power-down state only the Release from Power-down / Device ID command, which restores the device to
normal operation, will be recognized. All other commands are ignored. This includes the Read Status Register command, which is
always available during normal operation. The Deep Power-down mode therefore provides the maximum data protection against
unintended write operations. Deep Power-down mode automatically terminates when power is removed, and the device always
powers up in the standard standby mode. The device rejects any Deep Power-down command issued while it is executing a
program, erase, or Write Registers operation, and continues the operation uninterrupted.
Document Number: 002-00719 Rev. *K
Page 20 of 35
S25FL216K
Figure 8.12 Deep Power-down Command Sequence
CS #
M ode 3
SCK
0
1
2
3
4
5
6
t DP
7
M ode 0
M ode 3
M ode 0
In stru ctio n (B 9 H)
SI/IO0
H ig h Im p e d a n ce
SO
S ta n d a rd C u rre n t
8.13
P o w e r-d o w n C u rre n t
Release Deep Power-down / Device ID (ABh)
The Release from Deep Power-down / Device ID command is a multi-purpose command. The device requires the Release from
Deep Power-down command to exit the Deep Power-down mode. When the device is in the Deep Power-down mode, all commands
except Release from Deep Power-down command are ignored. In addition, the ABh command can also be used to read the device's
8-bit electronic Device ID.
When used only to release the device from the power-down state, the command is issued by driving the CS# pin low, shifting the
command code “ABh” and driving CS# high as shown in Figure 8.13. After the time duration of tRES1 (See AC Characteristics
on page 28.) the device will resume normal operation and other commands will be accepted. The CS# pin must remain high during
the tRES1 time duration.
When used only to obtain the Device ID while not in the Deep power-down state, the command is initiated by driving the CS# pin low
and shifting the command code “ABh” followed by 3-dummy bytes. The Device ID bits are then shifted out on the falling edge of SCK
with most significant bit (MSB) first as shown in Figure 8.14. The Device ID value for the S25FL216K is listed in Manufacturer and
Device Identification table. The Device ID can be read continuously. The command is completed by driving CS# high.
When used to release the device from the Deep power-down state and obtain the Device ID, the command is the same as
previously described, and shown in Figure 8.14, except that after CS# is driven high it must remain high for a time duration of tRES2
(See AC Characteristics on page 28.). After this time duration the device will resume normal operation and other commands will be
accepted. If the Release from Deep Power-down / Device ID command is issued while an Erase, Program or Write cycle is in
process (when WIP equals 1) the command is ignored and will not have any effects on the current cycle.
Figure 8.13 Release Deep Power-down Command
CS #
M ode 3
SCK
0
1
2
3
4
5
6
7
t RES 1
M ode 0
M ode 3
M ode 0
In stru ctio n (A B H)
SI/IO0
SO
H ig h Im p e d a n ce
Deep P o w e r-d o w n C u rre n t
H ig h P e rfo rm a n ce C u rre n t
Document Number: 002-00719 Rev. *K
S ta n d- b y C u rre n t
Page 21 of 35
S25FL216K
Figure 8.14 Release Deep Power-down / Device ID Command Sequence
CS #
SCK
Mode3
Mode0
0
1
2
3
4
5
6
7
8
9
Instruction (ABH )
10
28
29 30
31 32
36
37
38
Mode3
Mode0
tR ES2
3 Dum m y Bytes
SI/IO0
23
SO
High Im pedance
*
22
21
3
2
1
0
Device ID **
7
*
*=M SB
8.14
33 34 35
6
5
4
3
2
Power down Current
High Perform ance M ode Current
1
0
Stand -by
Current
Read Manufacturer / Device ID (90h)
The Read Manufacturer/Device ID command is an alternative to the Release from Deep Power-down /Device ID command that
provides both the JEDEC assigned manufacturer ID and the specific device ID.
The Read Manufacturer/Device ID command is very similar to the Release from Deep Power-down / Device ID command. The
command is initiated by driving the CS# pin low and shifting the command code “90h” followed by a 24-bit address (A23-A0) of
000000h. After which, the Manufacturer ID for Spansion (01h) and the Device ID are shifted out on the falling edge of SCK with most
significant bit (MSB) first as shown in Figure 8.15. The Device ID values for the S25FL216K are listed in Table 8.2 on page 12. If the
24-bit address is initially set to 000001h the Device ID will be read first, followed by the Manufacturer ID.
Document Number: 002-00719 Rev. *K
Page 22 of 35
S25FL216K
Figure 8.15 Read Manufacturer / Device ID Command Sequence
CS#
SCK
Mode3
Mode0
0
1
2
3
4
5
6
7
8
9
Instruction (90H)
SI/IO0
28 29 30 31
10
Address᧤000000H᧥
23 22 21
3
2
1
0
*
High Impedance
SO
CS#
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46
Mode3
Mode0
SCK
SI/IO0
Manufacturer ID
62
*=MSB
8.15
Device ID**
7
*
6
5
4
3
2
1
0
*
Read Identification (RDID) (9Fh)
For compatibility reasons, the S25FL216K provides several commands to electronically determine the identity of the device. The
Read JEDEC ID command is compatible with the JEDEC standard for SPI compatible serial memories that was adopted in 2003.
The command is initiated by driving the CS# pin low and shifting the command code “9Fh”. The JEDEC assigned Manufacturer ID
byte for Spansion (01h) and two Device ID bytes, Memory Type (ID15-ID8) and Capacity (ID7-ID0) are then shifted out on the falling
edge of SCK with most significant bit (MSB) first as shown in Figure 8.16. For memory type and capacity values refer to Table 8.2,
Manufacturer and Device Identification on page 12.
Document Number: 002-00719 Rev. *K
Page 23 of 35
S25FL216K
Figure 8.16 Read JEDEC ID Command Sequence
CS #
SCK
0
Mode3
Mode0
1
2
3
4
5
7
6
8
9
10
11
12 13
14 15
Instruction (9FH )
SI/IO0
M anufacturer ID
High Im pedance
SO
7
*
6
5
4
3
2
1
0
CS #
16
17
18
19 20
21
22
23
24 25
26
27
28 29
30 31
SCK
Mode3
Mode0
SI/IO0
M e m o ry T yp e ID 1 5- ID 8
SO
*= M SB
7
6
*
Document Number: 002-00719 Rev. *K
5
4
3
2
C a p a city ID 7 -ID 0
1
0
7
*
6
5
4
3
2
1
0
Page 24 of 35
S25FL216K
9. Electrical Specifications
9.1
Power-up Timing
Figure 9.1 Power-up Timing
V cc
V cc (m a x)
Program, E rase, and W rite Instruction are Ignored
C S # M ust T rack V cc
V cc (m in)
t VSL
R ead Instructions
A llow ed
D evice is F ully
A ccessible
Reset
Stast
VWI
tPUW
T im e
Table 9.1 Power-up Voltage and Timing
Parameter
Symbol
Type
Min
Max
Unit
VCC (min) to CS# Low
tVSL (1)
10
Time Delay Before Write Instruction
tPUW (1)
1
10
ms
Write Inhibit Threshold Voltage
VWI (1)
1
2
V
µs
Notes:
1. The parameters are characterized only.
2. VCC (max.) is 3.6V and VCC (min.) is 2.7V.
Document Number: 002-00719 Rev. *K
Page 25 of 35
S25FL216K
9.2
Absolute Maximum Ratings
Stresses above the values so mentioned above may cause permanent damage to the device. These values are for a stress rating
only and do not imply that the device should be operated at conditions up to or above these values.
Table 9.2 Absolute Maximum Ratings
Parameters
Symbol
Conditions
Range
Unit
Supply Voltage
VCC
Voltage applied on any pin
-0.6 to +4.0
V
VIO
Relative to Ground
-0.6 to VCC+0.4
V
Transient Voltage on any Pin
VIOT