S6E2C3AL0AGL2000A

S6E2C3 Series 32-bit ARM® Cortex®-M4F FM4 Microcontroller Devices in the S6E2C3 Series are highly integrated 32-bit microcontrollers with high performance and competitive cost. This series is based on the ARM Cortex-M4F processor with on-chip flash memory and SRAM. The series has peripherals such as motor control timers, A/D converters, and communications interfaces (USB, UART, CSIO (SPI), I2C, LIN). The products that are described in this data sheet are placed into TYPE3-M4 product categories "FM4 Family Peripheral Manual Main Part (002-04856)." Features External Bus Interface  Supports SRAM, NOR, NAND flash and SDRAM device 32-bit ARM Cortex-M4F Core  Processor version: r0p1  Up to 9 chip selects CS0 to CS8 (CS8 is only for SDRAM)  Up to 200 MHz frequency operation  8-/16-/32-bit data width  FPU built-in  Up to 25-bit address bus  Support DSP instructions  Memory protection unit (MPU): improves the reliability of an embedded system  Integrated nested vectored interrupt controller (NVIC): 1 NMI (non-maskable interrupt) and 128 peripheral interrupts and 16 priority levels  24-bit system timer (Sys Tick): system timer for OS task  Maximum Access size: 256M byte  Supports address/data multiplexing  Supports external RDY function  Supports scramble function  Possible to set the validity/invalidity of the scramble function for the external areas 0x6000_0000 to 0xDFFF_FFFF in 4 Mbytes units. management  Possible to set two kinds of the scramble key Note: It is necessary to use the Cypress provided software library to use the scramble function. On-chip Memories  Flash memory This series is based on two independent on-chip flash memories.  Up to 2048 Kbytes  Built-in flash accelerator system with 16 Kbytes trace buffer memory  Read access to flash memory that can be achieved without wait-cycle up to an operating frequency of 72 MHz. Even at the operating frequency more than 72 MHz, an equivalent single cycle access to flash memory can be obtained by the flash accelerator system.  Security function for code protection USB Interface (Max two Channels) The USB interface is composed of a device and a host.  USB device  USB 2.0 Full-speed supported 6 EndPoint supported • EndPoint 0 is control transfer • EndPoint 1, 2 can be selected bulk-transfer, interrupttransfer or isochronous-transfer • EndPoint 3 to 5 can select bulk-transfer or interrupttransfer • EndPoint 1 to 5 comprise double buffer  The size of each endpoint is as follows. • Endpoint 0, 2 to 5: 64 byte • EndPoint 1: 256 byte  Max  SRAM This is composed of three independent SRAMs (SRAM0, SRAM1 and SRAM2). SRAM0 is connected to the I-code bus or D-code bus of Cortex-M4F core. SRAM1 and SRAM2 are connected to system bus of Cortex-M4F core.  SRAM0: up to 192 Kbytes  SRAM1: 32 Kbytes  SRAM2: 32 Kbytes  USB host  USB2.0 Full-Speed/Low-Speed supported interrupt-transfer, and isochronous-transfer  Bulk-transfer, support Device connected/dis-connected automatically detect  IN/OUT token handshake packet automatically  Max 256-byte packet length supported  Wake-up function supported  USB Cypress Semiconductor Corporation Document Number: 002-04988 Rev. *C • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised March 12, 2018 S6E2C3 Series Multi-function Serial Interface (Max 16 channels)  Separate 64 byte receive and transmit FIFO buffers for channels 0 to 7.  Operation mode is selectable for each channel from the following:  UART  CSIO (SPI)  LIN  I2 C  UART  Full-duplex double buffer with or without parity supported  Built-in dedicated baud rate generator  External clock available as a serial clock  Various error detect functions available (parity errors, framing errors, and overrun errors)  Selection  CSIO (SPI)  Full-duplex double buffer dedicated baud rate generator  Overrun error detect function available  Serial chip select function (ch 6 and ch 7 only)  Supports high-speed SPI (ch 4 and ch 6 only)  Data length 5 to 16-bit  Built-in  LIN  LIN protocol Rev.2.1 supported  Full-duplex double buffer  Master/slave mode supported  LIN break field generation (can change to 13- to 16-bit length)  LIN break delimiter generation (can change to 1- to 4-bit length)  Various error detect functions available (parity errors, framing errors, and overrun errors)  I2 C  Standard mode (Max 100 kbps)/ Fast mode (Max 400 kbps) supported  Fast mode Plus (Fm+) (Max 1000 kbps, only for ch 3 = ch A and ch 7 = ch B) supported DMA Controller (Eight channels) DMA controller has an independent bus, so the CPU and DMA controller can process simultaneously.  Eight independently configured and operated channels  Transfer can be started by software or request from the builtin peripherals DSTC (Descriptor System data Transfer Controller; 256 Channels) The DSTC can transfer data at high-speed without going via the CPU. The DSTC adopts the descriptor system and, following the specified contents of the descriptor that has already been constructed on the memory, can access directly the memory/peripheral device and perform the data-transfer operation. It supports the software activation, the hardware activation, and the chain activation functions. A/D Converter (Max 32 channels)  12-bit A/D Converter  Successive approximation type three units  Conversion time: 0.5 μs at 5 V  Priority conversion available (priority at two levels)  Scanning conversion mode  Built-in FIFO for conversion data storage (for SCAN conversion: 16 steps, for priority conversion: 4 steps)  Built-in D/A Converter (Max 2 Channels)  R-2R type  12-bit resolution Base Timer (Max 16 Channels) Operation mode is selected from the following for each channel:  16-bit PWM timer  16-bit PPG timer  16-/32-bit reload timer  16-/32-bit PWC timer General Purpose I/O Port This series can use its pins as general purpose I/O ports when they are not used for external bus or peripherals; moreover, the port relocate function is built in. It can set the I/O port to which the peripheral function can be allocated.  Capable of pull-up control per pin  Capable of reading pin level directly  Transfer address area: 32-bit (4 GB)  Built-in port-relocate function  Transfer mode: Block transfer/Burst transfer/Demand  Up to 120 high-speed general-purpose I/O ports in 144-pin  Transfer data type: bytes/half-word/word  Some pins 5 V tolerant I/O. transfer  Transfer block count: 1 to 16 package See 4. Pin Descriptions and 5. I/O Circuit Type for the corresponding pins.  Number of transfers: 1 to 65536 Document Number: 002-04988 Rev. *C Page 2 of 198 S6E2C3 Series Multi-function Timer (Max three Units) Dual Timer (32-/16-bit Down Counter) The multi-function timer is composed of the following blocks: The dual timer consists of two programmable 32/16-bit down counters. Operation mode is selectable from the following for each channel: Minimum resolution: 5.00 ns  16-bit free-run timer × 3 ch/unit  Input capture × 4 ch/unit  Output compare × 6 ch/unit  A/D activation compare × 6 ch/unit  Waveform generator × 3 ch/unit  16-bit PPG timer × 3 ch/unit  Free-running  Periodic (= Reload)  One shot Watch Counter  PWM signal output function The watch counter is used for wake up from low-power consumption mode. It is possible to select the main clock, sub clock, built-in High-speed CR clock, or built-in low-speed CR clock as the clock source.  DC chopper waveform output function  Interval timer: up to 64 s (max) with a sub clock of The following functions can be used to achieve the motor control:  Dead time function 32.768 kHz  Input capture function  A/D convertor activate function External Interrupt Controller Unit  DTIF (motor emergency stop) interrupt function  External interrupt input pin: Max 32 pins  Include one non-maskable interrupt (NMI) Real-Time Clock (RTC) The real-time clock can count year, month, day, hour, minute, second, or day of the week from 00 to 99.  Interrupt function with specifying date and time (year/month/day/hour/minute) is available. This function is also available by specifying only year, month, day, hour, or minute.  Timer interrupt function after set time or each set time.  Capable of rewriting the time with continuing the time count.  Leap year automatic count is available. Quadrature Position/Revolution Counter (QPRC; Max four Channels) The Quadrature Position/Revolution Counter (QPRC) is used to measure the position of the position encoder. It is also possible to use up/down counter.  The detection edge of the three external event input pins AIN, BIN and ZIN is configurable. Watchdog Timer (2 Channels) A watchdog timer can generate interrupts or a reset when a time-out value is reached. This series consists of two different watchdogs: a "hardware" watchdog and a "software" watchdog. The hardware watchdog timer is clocked by low-speed internal CR oscillator. The hardware watchdog is thus active in any power saving mode except RTC mode and Stop mode. Cyclic Redundancy Check (CRC) Accelerator The CRC accelerator helps to verify data transmission or storage integrity. CCITT CRC16 and IEEE-802.3 CRC32 are supported.  CCITT CRC16 generator polynomial: 0x1021  IEEE-802.3 CRC32 generator polynomial: 0x04C11DB7  16-bit position counter  16-bit revolution counter  Two 16-bit compare registers Document Number: 002-04988 Rev. *C Page 3 of 198 S6E2C3 Series Programmable Cyclic Redundancy Check (PRGCRC) Accelerator Clock and Reset The CRC accelerator helps a verify data transmission or storage integrity. Five clock sources (two external oscillators, two internal CR oscillators, and Main PLL) that are dynamically selectable. CCITT CRC16, IEEE-802.3 CRC32 and generating polynomial are supported.  CCITT CRC16 generator polynomial: 0x1021  IEEE-802.3 CRC32 generator polynomial: 0x04C11DB7  Generating polynomial  Clocks  Main clock: 4 MHz to 48 MHz clock: 32.768 kHz  High-speed internal CR clock: 4 MHz  Low-speed internal CR clock: 100 kHz  Main PLL Clock  Sub  Resets  Reset requests from INITX pin on reset  Software reset  Watchdog timer reset  Low-voltage detector reset  Clock supervisor reset  Power SD Card Interface It is possible to use the SD card that conforms to the following standards.  Part 1 Physical Layer Specification version 3.01  Part E1 SDIO Specification version 3.00  Part A2 SD Host Controller Standard Specification version 3.00  1-bit or 4-bit data bus Clock Supervisor (CSV) Clocks generated by internal CR oscillators are used to supervise abnormality of the external clocks.  External OSC clock failure (clock stop) is detected, reset is asserted. I2S (Inter-IC Sound Bus) Interface (TX x 1 channel, RX x 1 channel)  External OSC frequency anomaly is detected, interrupt or reset is asserted.  Supports three transfer protocols  I2 S  Left justified  DSP mode  Separate clock generation block for flexible system integration options  Master/slave mode selectable  RX Only, TX Only or TX and RX simultaneous operation selectable Low-Voltage Detector (LVD) This Series include two-stage monitoring of voltage on the VCC pins. when the voltage falls below the voltage that has been set, the low-voltage detector function generates an interrupt or reset.  LVD1: error reporting via interrupt  LVD2: auto-reset operation  Word length is programmable from 7-bits to 32 bits  RX/TX FIFO integrated (RX: 66 words x 32-bits, TX: 66 words x 32-bits)  DMA, interrupts, or polling based data transfer supported High-Speed Quad SPI Up to 66 MHz clock rates for very fast data transfers to and from SPI compatible devices. Up to 256 Mbytes of memory mapped address space.  Single data rate (SDR)  Supports single, dual, and quad data modes  Built-in direct mode and command sequencer mode Low-power Consumption Mode Six low power consumption modes are supported.  Sleep  Timer  RTC  Stop  Deep standby RTC (selectable from with/without RAM retention)  Deep standby stop (selectable from with/without RAM retention)  Direct mode: Access by use of transmission FIFO/reception FIFO (up to16 word x 32 bit)  Command sequencer mode: Automatic access assigned to external device area. Document Number: 002-04988 Rev. *C Page 4 of 198 S6E2C3 Series Peripheral Clock Gating Unique ID The system can reduce the current consumption of the total system with gating the operation clocks of peripheral functions not used. Unique value of the device (41-bit) is set. Power Supply VBAT The consumption power during the RTC operation can be reduced by supplying the power supply independent from the RTC (calendar circuit)/32 kHz oscillation circuit. The following circuits can also be used.  RTC  32-kHz oscillation circuit  Four power supplies  Wide range voltage: VCC = 2.7 V to 5.5 V  Power supply for USB ch 0 I/O: USBVCC0 = 3.0 V to 3.6 V (when USB is used) = 2.7 V to 5.5 V (when GPIO is used)  Power supply for USB ch 1 I/O: USBVCC1 = 3.0 V to 3.6 V (when USB is used) = 2.7 V to 5.5 V (when GPIO is used)  Power supply for VBAT: VBAT = 1.65 V to 5.5 V  Power-on circuit  Back up register: 32 bytes  Port circuit Debug  Serial wire JTAG debug port (SWJ-DP)  Embedded trace macrocells (ETM) provide comprehensive debug and trace facilities.  AHB trace macrocells (HTM) Document Number: 002-04988 Rev. *C Page 5 of 198 S6E2C3 Series Table of Contents Features ................................................................................................................................................................................... 1 1. Product Lineup .................................................................................................................................................................. 8 2. Packages ........................................................................................................................................................................... 9 3. Pin Assignments ............................................................................................................................................................. 10 4. Pin Descriptions .............................................................................................................................................................. 14 5. I/O Circuit Type ............................................................................................................................................................... 62 6. Handling Precautions ..................................................................................................................................................... 70 6.1 Precautions for Product Design ................................................................................................................................... 70 6.2 Precautions for Package Mounting .............................................................................................................................. 71 6.3 Precautions for Use Environment ................................................................................................................................ 73 7. Handling Devices ............................................................................................................................................................ 74 8. Block Diagram ................................................................................................................................................................. 77 9. Memory Size .................................................................................................................................................................... 78 10. Memory Map .................................................................................................................................................................... 78 11. Pin Status in Each CPU State ........................................................................................................................................ 83 12. Electrical Characteristics ............................................................................................................................................... 91 12.1 Absolute Maximum Ratings ......................................................................................................................................... 91 12.2 Recommended Operating Conditions ......................................................................................................................... 93 12.3 DC Characteristics ...................................................................................................................................................... 97 12.3.1 Current Rating .......................................................................................................................................................... 97 12.3.2 Pin Characteristics .................................................................................................................................................. 107 12.4 AC Characteristics ..................................................................................................................................................... 109 12.4.1 Main Clock Input Characteristics ............................................................................................................................ 109 12.4.2 Sub Clock Input Characteristics .............................................................................................................................. 110 12.4.3 Built-In CR Oscillation Characteristics .................................................................................................................... 110 12.4.4 Operating Conditions of Main PLL (in the Case of Using Main Clock for Input Clock of PLL) ................................ 111 12.4.5 Operating Conditions of USB PLL・I2S PLL (in the Case of Using Main Clock for Input Clock of PLL) ................. 111 12.4.6 Operating Conditions of Main PLL (in the Case of Using Built-in High-speed CR Clock for Input Clock of Main PLL) ........................................................................................................................................................... 112 12.4.7 Reset Input Characteristics ..................................................................................................................................... 112 12.4.8 Power-On Reset Timing ......................................................................................................................................... 113 12.4.9 GPIO Output Characteristics .................................................................................................................................. 113 12.4.10 External Bus Timing................................................................................................................................................ 114 12.4.11 Base Timer Input Timing......................................................................................................................................... 125 12.4.12 CSIO (SPI) Timing .................................................................................................................................................. 126 12.4.13 External Input Timing .............................................................................................................................................. 159 12.4.14 Quadrature Position/Revolution Counter Timing .................................................................................................... 160 12.4.15 I2C Timing ............................................................................................................................................................... 163 12.4.16 SD Card Interface Timing ....................................................................................................................................... 165 12.4.17 ETM/ HTM Timing................................................................................................................................................... 167 12.4.18 JTAG Timing ........................................................................................................................................................... 168 12.4.19 I2S Timing ............................................................................................................................................................... 169 12.4.20 High-Speed Quad SPI Timing ................................................................................................................................ 174 12.5 12-bit A/D Converter .................................................................................................................................................. 176 12.6 12-bit D/A Converter .................................................................................................................................................. 179 12.7 USB Characteristics .................................................................................................................................................. 180 12.8 Low-Voltage Detection Characteristics ...................................................................................................................... 184 12.8.1 Low-Voltage Detection Reset ................................................................................................................................. 184 Document Number: 002-04988 Rev. *C Page 6 of 198 S6E2C3 Series 12.8.2 Interrupt of Low-Voltage Detection ......................................................................................................................... 184 12.9 MainFlash Memory Write/Erase Characteristics ........................................................................................................ 185 12.10 Dual Flash Memory Write/Erase Characteristics ....................................................................................................... 185 12.11 Standby Recovery Time ............................................................................................................................................ 186 12.11.1 Recovery cause: Interrupt/WKUP ........................................................................................................................... 186 12.11.2 Recovery Cause: Reset .......................................................................................................................................... 188 13. Ordering Information .................................................................................................................................................... 190 14. Package Diagrams ........................................................................................................................................................ 191 15. Major Changes .............................................................................................................................................................. 195 Document History ............................................................................................................................................................... 196 Sales, Solutions, and Legal Information ........................................................................................................................... 198 Document Number: 002-04988 Rev. *C Page 7 of 198 S6E2C3 Series 1. Product Lineup Memory Size Product Name On-chip flash memory On-chip SRAM SRAM0 SRAM1 SRAM2 S6E2C38H/J/L 1024 Kbytes 128 Kbytes 64 Kbytes 32 Kbytes 32 Kbytes S6E2C39H/J/L 1536 Kbytes 192 Kbytes 128 Kbytes 32 Kbytes 32 Kbytes S6E2C3AH/J/L 2048 Kbytes 256 Kbytes 192 Kbytes 32 Kbytes 32 Kbytes Function S6E2C38H0A S6E2C38J0A S6E2C38L0A S6E2C39H0A S6E2C39J0A S6E2C39L0A S6E2C3AH0A S6E2C3AJ0A S6E2C3AL0A 144 176/192 216 Cortex-M4F, MPU, NVIC 128 ch 200 MHz 2.7 V to 5.5 V 2 ch 8ch 256 ch Product Name Pin count CPU Freq. Power supply voltage range USB2.0 (device/host) DMAC DSTC External bus interface Addr: 25-bit (Max), Addr: 25-bit (Max), Addr: 25-bit (Max), Data: 8-/16-bit Data: 8-/16-bit Data: 8-/16-/32-bit CS: 9 (Max), CS: 9 (Max), CS: 9 (Max), SRAM, SRAM, SRAM, NOR flash NOR flash , NAND flash NAND flash NOR flash , NAND flash, SDRAM SDRAM Multi-function serial interface (UART/CSIO/LIN/I2C) Base timer (PWC/Reload timer/PWM/PPG) A/D activation compare Input capture Free-run timer Output compare Waveform generator PPG SD card interface I2 S High-speed quad SPI QPRC Dual timer Real-time clock Watch counter CRC accelerator Watchdog timer External interrupts I/O ports 12-bit A/D converter 12-bit D/A converter CSV (clock supervisor) LVD (low-voltage detector) 16ch (Max) ch 0 to ch 7：FIFO, ch 8 to ch 15：No FIFO 16 ch (Max) MF timer 6 ch 4 ch 3 ch 6 ch 3 ch 3 ch Built-in CR Debug function Unique ID Document Number: 002-04988 Rev. *C 3 units (Max) 1 unit - 120 pins (Max) 24 ch (3 units) High-speed Low-speed 1 unit 1 unit 4 ch (Max) 1 unit 1 unit 1 unit Yes (fixed, programmable) 1 ch (SW) + 1 ch (HW) 32 pins (Max)+ NMI × 1 152 pins (Max) 190 pins (Max) 32 ch (3 units) 2 units (Max) Yes 2 ch 4 MHz 100 kHz SWJ-DP/ETM/HTM Yes Page 8 of 198 S6E2C3 Series Notes: − All signals of the peripheral function in each product cannot be allocated by limiting the pins of package. It is necessary to use the port relocate function of the I/O port according to your function use. − See 12.4.3 Built-In CR Oscillation Characteristics for the accuracy of the built-in CR. 2. Packages Product Name Package LQFP: LQS144 LQFP: LQP176 BGA : LBE192 LQFP: LQQ216 : Supported (0.5-mm pitch) (0.5-mm pitch) (0.8-mm pitch) (0.4-mm pitch) S6E2C38H0A S6E2C39H0A S6E2C3AH0A  - - S6E2C38J0A S6E2C39J0A S6E2C3AJ0A -   - S6E2C38L0A S6E2C39L0A S6E2C3AL0A  Note: − See 14. Package Diagrams for detailed information on each package. Document Number: 002-04988 Rev. *C Page 9 of 198 S6E2C3 Series 3. Pin Assignments LQS144 VSS P81/UDP0 P80/UDM0 USBVCC0 P60/SIN4_0/INT31_0/WKUP3 P61/UHCONX0/SOT4_0/MALE_0/RTCCO_0/SUBOUT_0 P62/SCK4_0/MWEX_0 P63/ADTG_3/RTS4_0/INT30_0/MOEX_0 P6E/ADTG_5/SCK4_1/IC23_1/INT29_0 PD2/CTS4_1/FRCK2_1 PD1/INT31_1 PD0/INT30_1 PCF/RTS4_1/INT12_0 PCE/SIN4_1/INT15_0 PCD/SOT4_1/INT14_0 PCC PCB/INT28_0 VSS VCC PCA/TIOA15_0 PC9/TIOB15_0 PC8 PC7/INT13_0/CROUT_1 PC6/TIOA14_0 PC5/TIOB14_0 PC4/TIOA7_0 PC3/TIOB7_0 PC2/TIOA6_0 PC1/TIOB6_0 PC0 P04/TDO/SWO P03/TMS/SWDIO P02/TDI P01/TCK/SWCLK P00/TRSTX VCC 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 (Top View) VCC 1 108 VSS PA0/RTO20_0/TIOA8_0/AIN2_0/INT00_0/MADATA00_0 2 107 P83/UDP1 PA1/RTO21_0/TIOA9_0/BIN2_0/MADATA01_0 3 106 P82/UDM1 PA2/RTO22_0/TIOA10_0/ZIN2_0/MADATA02_0 4 105 USBVCC1 PA3/RTO23_0/TIOA11_0/MADATA03_0 5 104 P20/NMIX/WKUP0 PA4/RTO24_0/TIOA12_0/MADATA04_0 6 103 P21/ADTG_4/SIN0_0/INT27_0/CROUT_0 PA5/SIN1_0/RTO25_0/TIOA13_0/INT01_0/MADATA05_0 7 102 P22/AN31/SOT0_0/INT26_0 PA6/SOT1_0/DTTI2X_0/MADATA06_0 8 101 P23/UHCONX1/AN30/SCK0_0/TIOB13_1 PA7/SCK1_0/IC20_0/MADATA07_0 9 100 P24/AN29/TIOA13_1/MAD18_0 PA8/SIN7_0/IC21_0/INT02_0/WKUP1/MADATA08_0 10 99 P25/AN28/INT25_0/MAD17_0 PA9/SOT7_0/IC22_0/MADATA09_0 11 98 P26/MAD16_0 PAA/SCK7_0/IC23_0/MADATA10_0 12 97 P27/AN27/SIN5_0/INT24_0/MAD15_0 PAB/SCS70_0/FRCK2_0/INT03_0/MADATA11_0 13 96 P28/AN26/SOT5_0/MAD14_0 PAC/SCS71_0/TIOB8_0/AIN3_0/MADATA12_0 14 95 P29/AN25/SCK5_0/MAD13_0 PAD/SCK3_0/TIOB9_0/BIN3_0/MADATA13_0 15 94 P2A/AN24/CTS5_0/MAD12_0 PAE/ADTG_0/SOT3_0/TIOB10_0/ZIN3_0/MADATA14_0 16 93 P1F/AN15/RTS5_0/TIOB8_1/INT27_1/MAD11_0 PAF/SIN3_0/TIOB11_0/INT16_0/MADATA15_0 17 92 P1E/AN14/TIOA8_1/INT26_1/MAD10_0 P08/SIN14_0/TIOB12_0/INT17_0/MDQM0_0 18 91 P1D/AN13/SCK12_0/TIOB5_2/TRACED3 P09/SOT14_0/TIOB13_0/INT18_0/MDQM1_0 19 90 P1C/AN12/SOT12_0/TIOA5_2/TRACED2 P0A/ADTG_1/SCK14_0/AIN2_1/MCLKOUT_0 20 89 P1B/AN11/SIN12_0/TIOB4_2/INT11_0/TRACED1 P32/BIN2_1/INT19_0/S_DATA1_0 21 88 P1A/AN10/SCK2_0/TIOA4_2/TRACED0 P33/FRCK0_0/ZIN2_1/S_DATA0_0 22 87 P19/AN09/SOT2_0/TIOB3_2/INT24_1/TRACECLK P34/IC03_0/INT00_1/S_CLK_0 23 86 P18/AN08/SIN2_0/TIOA3_2/INT10_0 VCC 24 85 P17/AN07/SCK11_0/TIOB2_2/ZIN1_2 VSS 25 84 P16/AN06/SOT11_0/TIOA2_2/BIN1_2 P35/IC02_0/INT01_1/S_CMD_0 26 83 P15/AN05/SIN11_0/TIOB1_2/AIN1_2/INT09_0 P36/IC01_0/INT02_1/S_DATA3_0 27 82 P14/AN04/SOT6_1 P37/IC00_0/INT03_1/S_DATA2_0 28 81 P13/AN03/SIN6_1/INT25_1 P38/ADTG_2/DTTI0X_0/S_WP_0 29 80 P12/AN02/SCK10_0/TIOA1_2/ZIN0_2 P39/SIN2_1/RTO00_0/TIOA0_1/AIN3_1/INT16_1/S_CD_0/MAD24_0 30 79 P11/AN01/SOT10_0/TIOB0_2/BIN0_2 P3A/SOT2_1/RTO01_0/TIOA1_1/BIN3_1/INT17_1/MAD23_0 31 78 P10/AN00/SIN10_0/TIOA0_2/AIN0_2/INT08_0 P3B/SCK2_1/RTO02_0/TIOA2_1/ZIN3_1/INT18_1/MAD22_0/MNALE_0 32 77 AVRH P3C/SIN13_0/RTO03_0/TIOA3_1/INT19_1/MAD21_0/MNCLE_0 33 76 AVRL P3D/SOT13_0/RTO04_0/TIOA4_1/MAD20_0/MNWEX_0 34 75 AVSS P3E/SCK13_0/RTO05_0/TIOA5_1/MAD19_0/MNREX_0 35 74 AVCC VSS 36 73 VCC 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 VCC P40/SIN3_1/RTO10_0/TIOA0_0/AIN0_0/INT23_0/MCSX7_0 P41/SOT3_1/RTO11_0/TIOA1_0/BIN0_0/MCSX6_0 P42/SCK3_1/RTO12_0/TIOA2_0/ZIN0_0/MCSX5_0 P43/SIN15_0/RTO13_0/TIOA3_0/INT04_0/MCSX4_0 P44/SOT15_0/RTO14_0/TIOA4_0/MCSX3_0 P45/SCK15_0/RTO15_0/TIOA5_0/MCSX2_0 C VSS VCC P7D/SCK1_1/DTTI1X_0/INT05_0/WKUP2/MCSX1_0 P7E/ADTG_7/FRCK1_0/MCSX0_0 INITX P46/X0A P47/X1A VBAT P48/VREGCTL P49/VWAKEUP P70/ADTG_8/SIN1_1/INT06_0/MRDY_0 P71/SOT1_1/MAD00_0 P72/SIN9_0/TIOB0_0/INT07_0/MAD01_0 P73/SOT9_0/TIOB1_0/MAD02_0 P74/SCK9_0/TIOB2_0/MAD03_0 P75/SIN8_0/TIOB3_0/AIN1_0/INT20_0/MAD04_0 P76/SOT8_0/TIOB4_0/BIN1_0/MAD05_0 P77/SCK8_0/TIOB5_0/ZIN1_0/MAD06_0 P78/SIN6_0/IC10_0/INT21_0/MAD07_0 P79/SOT6_0/IC11_0/MAD08_0 P7A/SCK6_0/IC12_0/MAD09_0 P7B/DA1/SCS60_0/IC13_0/INT22_0 P7C/DA0/SCS61_0/INT04_1 PE0/MD1 MD0 PE2/X0 PE3/X1 VSS LQFP - 144 Note: − The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR) to select the pin. Document Number: 002-04988 Rev. *C Page 10 of 198 S6E2C3 Series LQP176 VSS P81/UDP0 P80/UDM0 USBVCC0 P60/SIN4_0/INT31_0/WKUP3 P61/UHCONX0/SOT4_0/MALE_0/RTCCO_0/SUBOUT_0 P62/SCK4_0/MWEX_0 P63/ADTG_3/RTS4_0/INT30_0/MOEX_0 P64/CTS4_0/RTO25_1/INT29_1 P65/RTO24_1/INT28_1 P6E/ADTG_5/SCK4_1/IC23_1/INT29_0 PD2/CTS4_1/FRCK2_1 PD1/INT31_1 PD0/INT30_1 PCF/RTS4_1/INT12_0 PCE/SIN4_1/INT15_0 PCD/SOT4_1/INT14_0 PCC PCB/INT28_0 VSS VCC PCA/TIOA15_0 PC9/TIOB15_0 PC8 PC7/INT13_0/CROUT_1 PC6/TIOA14_0 PC5/TIOB14_0 PC4/TIOA7_0 PC3/TIOB7_0 PC2/TIOA6_0 PC1/TIOB6_0 PC0 P95/RTS5_1/Q_CS0_0 P94/CTS5_1/Q_SCK_0 P93/SCK5_1/INT15_1/Q_IO0_0 P92/SOT5_1/INT14_1/Q_IO1_0 P91/SIN5_1/INT13_1/Q_IO2_0 P90/INT12_1/Q_IO3_0 P04/TDO/SWO P03/TMS/SWDIO P02/TDI P01/TCK/SWCLK P00/TRSTX VCC 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 (Top View) VCC 1 132 VSS PA0/RTO20_0/TIOA8_0/AIN2_0/INT00_0/MADATA00_0 2 131 P83/UDP1 PA1/RTO21_0/TIOA9_0/BIN2_0/MADATA01_0 3 130 P82/UDM1 PA2/RTO22_0/TIOA10_0/ZIN2_0/MADATA02_0 4 129 USBVCC1 PA3/RTO23_0/TIOA11_0/MADATA03_0 5 128 P20/NMIX/WKUP0 PA4/RTO24_0/TIOA12_0/MADATA04_0 6 127 P21/ADTG_4/SIN0_0/INT27_0/CROUT_0 PA5/SIN1_0/RTO25_0/TIOA13_0/INT01_0/MADATA05_0 7 126 P22/AN31/SOT0_0/INT26_0 PA6/SOT1_0/DTTI2X_0/MADATA06_0 8 125 P23/UHCONX1/AN30/SCK0_0/TIOB13_1 PA7/SCK1_0/IC20_0/MADATA07_0 9 124 P24/AN29/TIOA13_1/MAD18_0 P50/SCS72_0/RTO00_1/TIOA8_2 10 123 P25/AN28/INT25_0/MAD17_0 P51/SCS73_0/RTO01_1/TIOB8_2 11 122 P26/MAD16_0 P52/RTO02_1/TIOA9_2 12 121 P27/AN27/SIN5_0/INT24_0/MAD15_0 PA8/SIN7_0/IC21_0/INT02_0/WKUP1/MADATA08_0 13 120 P28/AN26/SOT5_0/MAD14_0 PA9/SOT7_0/IC22_0/MADATA09_0 14 119 P29/AN25/SCK5_0/MAD13_0 PAA/SCK7_0/IC23_0/MADATA10_0 15 118 P2A/AN24/CTS5_0/MAD12_0 PAB/SCS70_0/FRCK2_0/INT03_0/MADATA11_0 16 117 P1F/AN15/RTS5_0/TIOB8_1/INT27_1/MAD11_0 PAC/SCS71_0/TIOB8_0/AIN3_0/MADATA12_0 17 116 P1E/AN14/TIOA8_1/INT26_1/MAD10_0 PAD/SCK3_0/TIOB9_0/BIN3_0/MADATA13_0 18 115 PB7/AN23/TIOB12_1/TRACED7 PAE/ADTG_0/SOT3_0/TIOB10_0/ZIN3_0/MADATA14_0 19 114 PB6/AN22/SCK8_1/TIOA12_1/TRACED6 PAF/SIN3_0/TIOB11_0/INT16_0/MADATA15_0 20 113 PB5/AN21/SOT8_1/TIOB11_1/INT11_1/TRACED5 P08/SIN14_0/TIOB12_0/INT17_0/MDQM0_0 21 112 PB4/AN20/SIN8_1/TIOA11_1/INT10_1/TRACED4 P09/SOT14_0/TIOB13_0/INT18_0/MDQM1_0 22 111 P1D/AN13/SCK12_0/TIOB5_2/TRACED3 P0A/ADTG_1/SCK14_0/AIN2_1/MCLKOUT_0 23 110 P1C/AN12/SOT12_0/TIOA5_2/TRACED2 P30/TIOA13_2/INT03_2/I2SDI0_0 24 109 P1B/AN11/SIN12_0/TIOB4_2/INT11_0/TRACED1 P31/TIOB13_2/I2SCK0_0 25 108 P1A/AN10/SCK2_0/TIOA4_2/TRACED0 P32/BIN2_1/INT19_0/S_DATA1_0 26 107 P19/AN09/SOT2_0/TIOB3_2/INT24_1/TRACECLK P33/FRCK0_0/ZIN2_1/S_DATA0_0 27 106 P18/AN08/SIN2_0/TIOA3_2/INT10_0 P34/IC03_0/INT00_1/S_CLK_0 28 105 PB3/AN19/SCS62_1/TIOB10_1 VCC 29 104 PB2/AN18/SCS61_1/TIOA10_1/INT09_1 VSS 30 103 PB1/AN17/SCS60_1/TIOB9_1/INT08_1 P35/IC02_0/INT01_1/S_CMD_0 31 102 PB0/AN16/SCK6_1/TIOA9_1 P36/IC01_0/INT02_1/S_DATA3_0 32 101 P17/AN07/SCK11_0/TIOB2_2/ZIN1_2 P37/IC00_0/INT03_1/S_DATA2_0 33 100 P16/AN06/SOT11_0/TIOA2_2/BIN1_2 P38/ADTG_2/DTTI0X_0/S_WP_0 34 99 P15/AN05/SIN11_0/TIOB1_2/AIN1_2/INT09_0 P39/SIN2_1/RTO00_0/TIOA0_1/AIN3_1/INT16_1/S_CD_0/MAD24_0 35 98 P14/AN04/SOT6_1 P3A/SOT2_1/RTO01_0/TIOA1_1/BIN3_1/INT17_1/MAD23_0 36 97 P13/AN03/SIN6_1/INT25_1 P3B/SCK2_1/RTO02_0/TIOA2_1/ZIN3_1/INT18_1/MAD22_0/MNALE_0 37 96 P12/AN02/SCK10_0/TIOA1_2/ZIN0_2 P3C/SIN13_0/RTO03_0/TIOA3_1/INT19_1/MAD21_0/MNCLE_0 38 95 P11/AN01/SOT10_0/TIOB0_2/BIN0_2 P3D/SOT13_0/RTO04_0/TIOA4_1/MAD20_0/MNWEX_0 39 94 P10/AN00/SIN10_0/TIOA0_2/AIN0_2/INT08_0 P3E/SCK13_0/RTO05_0/TIOA5_1/MAD19_0/MNREX_0 40 93 AVRH P5D/SIN10_1/TIOB11_2/INT01_2/I2SMCLK0_0 41 92 AVRL P5E/SOT10_1/TIOA12_2/I2SDO0_0 42 91 AVSS P5F/SCK10_1/TIOB12_2/I2SWS0_0 43 90 AVCC VSS 44 89 VCC 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 VCC P40/SIN3_1/RTO10_0/TIOA0_0/AIN0_0/INT23_0/MCSX7_0 P41/SOT3_1/RTO11_0/TIOA1_0/BIN0_0/MCSX6_0 P42/SCK3_1/RTO12_0/TIOA2_0/ZIN0_0/MCSX5_0 P43/SIN15_0/RTO13_0/TIOA3_0/INT04_0/MCSX4_0 P44/SOT15_0/RTO14_0/TIOA4_0/MCSX3_0 P45/SCK15_0/RTO15_0/TIOA5_0/MCSX2_0 C VSS VCC P7D/SCK1_1/DTTI1X_0/INT05_0/WKUP2/MCSX1_0 P7E/ADTG_7/FRCK1_0/MCSX0_0 INITX P46/X0A P47/X1A VBAT P48/VREGCTL P49/VWAKEUP PF0/SCS63_0/FRCK1_1/TIOA15_1/INT22_1 PF1/SCS62_0/TIOB15_1/INT23_1 P70/ADTG_8/SIN1_1/INT06_0/MRDY_0 P71/SOT1_1/MAD00_0 P72/SIN9_0/TIOB0_0/INT07_0/MAD01_0 P73/SOT9_0/TIOB1_0/MAD02_0 P74/SCK9_0/TIOB2_0/MAD03_0 PF2/RTO10_1/TIOA6_1/MRASX_0 PF3/RTO11_1/TIOB6_1/INT05_1/MCASX_0 PF4/RTO12_1/TIOA7_1/INT06_1/MSDWEX_0 PF5/RTO13_1/TIOB7_1/INT07_1/MCSX8_0 PF6/RTO14_1/TIOA14_1/INT20_1/MSDCKE_0 PF7/RTO15_1/TIOB14_1/INT21_1/MSDCLK_0 P75/SIN8_0/TIOB3_0/AIN1_0/INT20_0/MAD04_0 P76/SOT8_0/TIOB4_0/BIN1_0/MAD05_0 P77/SCK8_0/TIOB5_0/ZIN1_0/MAD06_0 P78/SIN6_0/IC10_0/INT21_0/MAD07_0 P79/SOT6_0/IC11_0/MAD08_0 P7A/SCK6_0/IC12_0/MAD09_0 P7B/DA1/SCS60_0/IC13_0/INT22_0 P7C/DA0/SCS61_0/INT04_1 PE0/MD1 MD0 PE2/X0 PE3/X1 VSS LQFP - 176 Note: − The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR) to select the pin. Document Number: 002-04988 Rev. *C Page 11 of 198 S6E2C3 Series LQQ216 VCC 1 PA0/RTO20_0/TIOA8_0/AIN2_0/INT00_0/MADATA00_0 P02/TDI P01/TCK/SWCLK P00/TRSTX VCC 166 165 164 163 P91/SIN5_1/INT13_1/Q_IO2_0 P90/INT12_1/Q_IO3_0 P04/TDO/SWO P03/TMS/SWDIO 170 169 168 167 P94/CTS5_1/Q_SCK_0 P93/SCK5_1/INT15_1/Q_IO0_0 P92/SOT5_1/INT14_1/Q_IO1_0 173 172 171 PC0 P97/INT13_2/Q_CS2_0 P96/INT12_2/Q_CS1_0 P95/RTS5_1/Q_CS0_0 177 176 175 174 PC3/TIOB7_0 PC2/TIOA6_0 PC1/TIOB6_0 180 179 178 PC7/INT13_0/CROUT_1 PC6/TIOA14_0 PC5/TIOB14_0 PC4/TIOA7_0 184 183 182 181 PCA/TIOA15_0 PC9/TIOB15_0 PC8 187 186 185 PCC PCB/INT28_0 VSS VCC 191 190 189 188 PCF/RTS4_1/INT12_0 PCE/SIN4_1/INT15_0 PCD/SOT4_1/INT14_0 194 193 192 P6E/ADTG_5/SCK4_1/IC23_1/INT29_0 PD2/CTS4_1/FRCK2_1 PD1/INT31_1 PD0/INT30_1 198 197 196 195 P6B/SIN14_1/IC20_1/TIOB7_2/INT14_2 P6C/SOT14_1/IC21_1/TIOA6_2 P6D/SCK14_1/IC22_1/TIOB6_2 201 200 199 P67/SOT13_1/RTO22_1/TIOB15_2 P68/SCK13_1/RTO21_1/TIOA14_2 P69/RTO20_1/TIOB14_2 P6A/DTTI2X_1/TIOA7_2 205 204 203 202 P64/CTS4_0/RTO25_1/INT29_1 P65/RTO24_1/INT28_1 P66/SIN13_1/RTO23_1/TIOA15_2/INT15_2 208 207 206 P60/SIN4_0/INT31_0/WKUP3 P61/UHCONX0/SOT4_0/MALE_0/RTCCO_0/SUBOUT_0 P62/SCK4_0/MWEX_0 P63/ADTG_3/RTS4_0/INT30_0/MOEX_0 212 211 210 209 VSS P81/UDP0 P80/UDM0 USBVCC0 216 215 214 213 (Top View) 162 VSS 2 161 P83/UDP1 PA1/RTO21_0/TIOA9_0/BIN2_0/MADATA01_0 3 160 P82/UDM1 PA2/RTO22_0/TIOA10_0/ZIN2_0/MADATA02_0 4 159 USBVCC1 PA3/RTO23_0/TIOA11_0/MADATA03_0 5 158 P20/NMIX/WKUP0 PA4/RTO24_0/TIOA12_0/MADATA04_0 6 157 P21/ADTG_4/SIN0_0/INT27_0/CROUT_0 PA5/SIN1_0/RTO25_0/TIOA13_0/INT01_0/MADATA05_0 7 156 P22/AN31/SOT0_0/INT26_0 PA6/SOT1_0/DTTI2X_0/MADATA06_0 8 155 P23/UHCONX1/AN30/SCK0_0/TIOB13_1 PA7/SCK1_0/IC20_0/MADATA07_0 9 154 P24/AN29/TIOA13_1/MAD18_0 P50/SCS72_0/RTO00_1/TIOA8_2/MADATA16_0 10 153 P25/AN28/INT25_0/MAD17_0 P51/SCS73_0/RTO01_1/TIOB8_2/MADATA17_0 11 152 P26/MAD16_0 P52/RTO02_1/TIOA9_2/MADATA18_0 12 151 PBF/SIN0_1/ZIN3_2/INT11_2/TRACED15 P53/RTO03_1/TIOB9_2/MADATA19_0 13 150 PBE/SOT0_1/BIN3_2/TRACED14 PA8/SIN7_0/IC21_0/INT02_0/WKUP1/MADATA08_0 14 149 PBD/SCK0_1/AIN3_2/INT10_2/TRACED13 PA9/SOT7_0/IC22_0/MADATA09_0 15 148 PBC/TRACED12 PAA/SCK7_0/IC23_0/MADATA10_0 16 147 P27/AN27/SIN5_0/INT24_0/MAD15_0 PAB/SCS70_0/FRCK2_0/INT03_0/MADATA11_0 17 146 P28/AN26/SOT5_0/MAD14_0 PAC/SCS71_0/TIOB8_0/AIN3_0/MADATA12_0 18 145 P29/AN25/SCK5_0/MAD13_0 P54/SIN15_1/RTO04_1/TIOA10_2/INT00_2/MADATA20_0 19 144 P2A/AN24/CTS5_0/MAD12_0 P55/SOT15_1/RTO05_1/TIOB10_2/MADATA21_0 20 143 P1F/AN15/RTS5_0/TIOB8_1/INT27_1/MAD11_0 P56/SCK15_1/DTTI0X_1/TIOB0_1/MADATA22_0 21 142 P1E/AN14/TIOA8_1/INT26_1/MAD10_0 P57/IC00_1/TIOB1_1/MADATA23_0 22 141 PB7/AN23/TIOB12_1/TRACED7 PAD/SCK3_0/TIOB9_0/BIN3_0/MADATA13_0 23 140 PB6/AN22/SCK8_1/TIOA12_1/TRACED6 PAE/ADTG_0/SOT3_0/TIOB10_0/ZIN3_0/MADATA14_0 24 139 PB5/AN21/SOT8_1/TIOB11_1/INT11_1/TRACED5 PAF/SIN3_0/TIOB11_0/INT16_0/MADATA15_0 25 138 PB4/AN20/SIN8_1/TIOA11_1/INT10_1/TRACED4 P58/SIN11_1/IC01_1/TIOB2_1/INT02_2/MADATA24_0 26 137 VCC P59/SOT11_1/IC02_1/TIOB3_1/MADATA25_0 27 136 VSS P5A/SCK11_1/IC03_1/TIOB4_1/MADATA26_0 28 135 P1D/AN13/SCK12_0/TIOB5_2/TRACED3 P5B/FRCK0_1/TIOB5_1/MADATA27_0 29 134 P1C/AN12/SOT12_0/TIOA5_2/TRACED2 P08/SIN14_0/TIOB12_0/INT17_0/MDQM0_0 30 133 P1B/AN11/SIN12_0/TIOB4_2/INT11_0/TRACED1 P09/SOT14_0/TIOB13_0/INT18_0/MDQM1_0 31 132 P1A/AN10/SCK2_0/TIOA4_2/TRACED0 P0A/ADTG_1/SCK14_0/AIN2_1/MCLKOUT_0 32 131 P19/AN09/SOT2_0/TIOB3_2/INT24_1/TRACECLK P5C/TIOA11_2/MADATA28_0/RTCCO_1/SUBOUT_1 33 130 P18/AN08/SIN2_0/TIOA3_2/INT10_0 P30/TIOA13_2/INT03_2/MDQM2_0/I2SDI0_0 34 129 PB3/AN19/SCS62_1/TIOB10_1 P31/TIOB13_2/MDQM3_0/I2SCK0_0 35 128 PB2/AN18/SCS61_1/TIOA10_1/INT09_1 P32/BIN2_1/INT19_0/S_DATA1_0 36 127 PB1/AN17/SCS60_1/TIOB9_1/INT08_1 P33/FRCK0_0/ZIN2_1/S_DATA0_0 37 126 PB0/AN16/SCK6_1/TIOA9_1 P34/IC03_0/INT00_1/S_CLK_0 38 125 P17/AN07/SCK11_0/TIOB2_2/ZIN1_2 VCC 39 124 P16/AN06/SOT11_0/TIOA2_2/BIN1_2 VSS 40 123 P15/AN05/SIN11_0/TIOB1_2/AIN1_2/INT09_0 P35/IC02_0/INT01_1/S_CMD_0 41 122 PBB/SCK9_1/ZIN2_2/TRACED11 P36/IC01_0/INT02_1/S_DATA3_0 42 121 PBA/SOT9_1/BIN2_2/TRACED10 P37/IC00_0/INT03_1/S_DATA2_0 43 120 PB9/SIN9_1/AIN2_2/INT09_2/TRACED9 P38/ADTG_2/DTTI0X_0/S_WP_0 44 119 PB8/ADTG_6/SCS63_1/INT08_2/TRACED8 P39/SIN2_1/RTO00_0/TIOA0_1/AIN3_1/INT16_1/S_CD_0/MAD24_0 45 118 P14/AN04/SOT6_1 P3A/SOT2_1/RTO01_0/TIOA1_1/BIN3_1/INT17_1/MAD23_0 46 117 P13/AN03/SIN6_1/INT25_1 P3B/SCK2_1/RTO02_0/TIOA2_1/ZIN3_1/INT18_1/MAD22_0/MNALE_0 47 116 P12/AN02/SCK10_0/TIOA1_2/ZIN0_2 P3C/SIN13_0/RTO03_0/TIOA3_1/INT19_1/MAD21_0/MNCLE_0 48 115 P11/AN01/SOT10_0/TIOB0_2/BIN0_2 P3D/SOT13_0/RTO04_0/TIOA4_1/MAD20_0/MNWEX_0 49 114 P10/AN00/SIN10_0/TIOA0_2/AIN0_2/INT08_0 LQFP - 216 105 106 107 108 MD0 PE2/X0 VSS PE0/MD1 PE3/X1 101 102 103 104 PFA/SCK7_1/IC11_1/ZIN1_1 PFC/SIN7_1/IC13_1/INT06_2 P7C/DA0/SCS61_0/INT04_1 PFB/SOT7_1/IC12_1/INT07_2 98 99 100 P7A/SCK6_0/IC12_0/MAD09_0 PF9/SCS71_1/IC10_1/BIN1_1 P79/SOT6_0/IC11_0/MAD08_0 P7B/DA1/SCS60_0/IC13_0/INT22_0 94 95 96 97 PF8/SCS70_1/DTTI1X_1/AIN1_1 P77/SCK8_0/TIOB5_0/ZIN1_0/MAD06_0 P78/SIN6_0/IC10_0/INT21_0/MAD07_0 91 92 93 P76/SOT8_0/TIOB4_0/BIN1_0/MAD05_0 PF5/RTO13_1/TIOB7_1/INT07_1/MCSX8_0 PF7/RTO15_1/TIOB14_1/INT21_1/MSDCLK_0 P75/SIN8_0/TIOB3_0/AIN1_0/INT20_0/MAD04_0 87 88 89 90 PF4/RTO12_1/TIOA7_1/INT06_1/MSDWEX_0 PF6/RTO14_1/TIOA14_1/INT20_1/MSDCKE_0 84 85 86 P74/SCK9_0/TIOB2_0/MAD03_0 PF2/RTO10_1/TIOA6_1/MRASX_0 P71/SOT1_1/MAD00_0 P73/SOT9_0/TIOB1_0/MAD02_0 PF3/RTO11_1/TIOB6_1/INT05_1/MCASX_0 80 81 82 83 P70/ADTG_8/SIN1_1/INT06_0/MRDY_0 P72/SIN9_0/TIOB0_0/INT07_0/MAD01_0 77 78 79 P49/VWAKEUP PF1/SCS62_0/TIOB15_1/INT23_1 VBAT PF0/SCS63_0/FRCK1_1/TIOA15_1/INT22_1 73 74 75 76 P46/X0A P47/X1A P48/VREGCTL 70 71 72 INITX P4E/SCS73_1 P7E/ADTG_7/FRCK1_0/MCSX0_0 P4C/SCK12_1/ZIN0_1 P7D/SCK1_1/DTTI1X_0/INT05_0/WKUP2/MCSX1_0 66 67 68 69 P4B/SOT12_1/BIN0_1 P4D/SCS72_1/INT05_2 63 64 65 VSS VCC P4A/SIN12_1/AIN0_1/INT04_2 59 60 61 VCC 62 109 C 54 P44/SOT15_0/RTO14_0/TIOA4_0/MCSX3_0 AVCC VSS P45/SCK15_0/RTO15_0/TIOA5_0/MCSX2_0 110 P43/SIN15_0/RTO13_0/TIOA3_0/INT04_0/MCSX4_0 53 55 AVSS P5F/SCK10_1/TIOB12_2/MADATA31_0/I2SWS0_0 56 111 57 52 58 AVRL P5E/SOT10_1/TIOA12_2/MADATA30_0/I2SDO0_0 VCC AVRH 112 P42/SCK3_1/RTO12_0/TIOA2_0/ZIN0_0/MCSX5_0 113 51 P41/SOT3_1/RTO11_0/TIOA1_0/BIN0_0/MCSX6_0 50 P40/SIN3_1/RTO10_0/TIOA0_0/AIN0_0/INT23_0/MCSX7_0 P3E/SCK13_0/RTO05_0/TIOA5_1/MAD19_0/MNREX_0 P5D/SIN10_1/TIOB11_2/INT01_2/MADATA29_0/I2SMCLK0_0 Note: − The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR) to select the pin. Document Number: 002-04988 Rev. *C Page 12 of 198 S6E2C3 Series LBE192 (Top View) 1 A 2 3 UDP0 UDM0 4 5 6 7 8 9 10 11 12 13 14 USBV VSS PCD PCB VSS VCC PC8 VSS TCK VCC CC0 B VSS PA0 P60 P62 P64 PD1 PCA PC1 P95 P92 TDO TMS C VCC PA1 PA2 P61 P63 PD2 PCC PC5 PC0 P93 P90 D PA5 PA4 PA6 PA7 PA3 P6E PCE PC6 PC2 P94 P91 P22 P21 UDM1 E VSS P50 P51 P52 PA8 P65 PCF PC7 PC3 P26 P25 P24 P23 F PA9 PAA PAB PAC PAD PAE PD0 PC9 PC4 P2A P29 P28 P27 PB5 G VSS PAF P08 P09 P0A P30 VSS VSS P1F P1E PB7 PB6 PB4 P1B H VCC P32 P34 P31 VSS P35 VSS VSS P18 PB2 P1D P19 P1C P1A J P33 P39 P38 P37 P36 P71 VSS P74 PB1 PB0 P17 P16 P15 PB3 K P3A P3B P3C P3D PF0 PF1 VSS P73 P75 P79 P14 P12 P11 P13 L P3E P5D P5E P43 P7D P70 VSS P72 PF7 P78 P10 AVRH AVRL VSS M VSS P5F P42 P44 P7E P49 VSS PF3 PF6 P7A P7C AVSS AVCC VCC N VCC P40 P41 P45 INITX P48 VSS PF2 PF4 P77 P7B MD0 MD1 VSS P C VSS VCC X0A X1A VSS VBAT PF5 P76 VSS TRSTX VSS TDI P20 UDP1 X0 USBV CC1 X1 PFBGA-192 Note: − The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR) to select the pin. Document Number: 002-04988 Rev. *C Page 13 of 198 S6E2C3 Series 4. Pin Descriptions List of Pin Functions The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR) to select the pin. Pin Number LQQ216 LQP176 LQS144 LBE192 1 1 1 C1 2 2 2 B2 3 3 3 C2 4 4 4 C3 5 5 5 D5 6 6 6 D2 7 7 7 D1 8 8 8 D3 9 9 9 D4 Document Number: 002-04988 Rev. *C Pin Name VCC PA0 RTO20_0 (PPG20_0) TIOA8_0 AIN2_0 INT00_0 MADATA00_0 PA1 RTO21_0 (PPG20_0) TIOA9_0 BIN2_0 MADATA01_0 PA2 RTO22_0 (PPG22_0) TIOA10_0 ZIN2_0 MADATA02_0 PA3 RTO23_0 (PPG22_0) TIOA11_0 MADATA03_0 PA4 RTO24_0 (PPG24_0) TIOA12_0 MADATA04_0 PA5 SIN1_0 RTO25_0 (PPG24_0) TIOA13_0 INT01_0 MADATA05_0 PA6 SOT1_0 (SDA1_0)) DTTI2X_0 MADATA06_0 PA7 SCK1_0 (SCL1_0) IC20_0 MADATA07_0 I/O Circuit Type - Pin State Type G K G I G I G I G I G K E I E I - Page 14 of 198 S6E2C3 Series Pin Number LQQ216 LQP176 LQS144 LBE192 10 10 - E2 11 11 - E3 12 12 - E4 13 - - - 14 13 10 E5 15 14 11 F1 16 15 12 F2 17 16 13 F3 18 17 14 F4 19 - - - Document Number: 002-04988 Rev. *C Pin Name P50 SCS72_0 RTO00_1 (PPG00_1) TIOA8_2 MADATA16_0 P51 SCS73_0 RTO01_1 (PPG00_1) TIOB8_2 MADATA17_0 P52 RTO02_1 (PPG02_1) TIOA9_2 MADATA18_0 P53 RTO03_1 (PPG02_1) TIOB9_2 MADATA19_0 PA8 SIN7_0 IC21_0 INT02_0 WKUP1 MADATA08_0 PA9 SOT7_0 (SDA7_0) IC22_0 MADATA09_0 PAA SCK7_0 (SCL7_0) IC23_0 MADATA10_0 PAB SCS70_0 FRCK2_0 INT03_0 MADATA11_0 PAC SCS71_0 TIOB8_0 AIN3_0 MADATA12_0 P54 SIN15_1 RTO04_1 (PPG04_1) TIOA10_2 INT00_2 MADATA20_0 I/O Circuit Type Pin State Type E I E I E I E I I Q N I N I E K E I E K Page 15 of 198 S6E2C3 Series Pin Number LQQ216 LQP176 LQS144 LBE192 20 - - - 21 - - - 22 - - - 23 18 15 F5 24 19 16 F6 25 20 17 G2 26 - - - 27 - - - 28 - - - Document Number: 002-04988 Rev. *C Pin Name P55 SOT15_1 (SDA15_1) RTO05_1 (PPG04_1) TIOB10_2 MADATA21_0 P56 SCK15_1 (SCL15_1) DTTI0X_1 TIOB0_1 MADATA22_0 P57 IC00_1 TIOB1_1 MADATA23_0 PAD SCK3_0 (SCL3_0) TIOB9_0 BIN3_0 MADATA13_0 PAE ADTG_0 SOT3_0 (SDA3_0) TIOB10_0 ZIN3_0 MADATA14_0 PAF SIN3_0 TIOB11_0 INT16_0 MADATA15_0 P58 SIN11_1 IC01_1 TIOB2_1 INT02_2 MADATA24_0 P59 SOT11_1 (SDA11_1) IC02_1 TIOB3_1 MADATA25_0 P5A SCK11_1 (SCL11_1) IC03_1 TIOB4_1 MADATA26_0 I/O Circuit Type Pin State Type E I E I E I N I N I I K E K E I E I Page 16 of 198 S6E2C3 Series Pin Number LQQ216 LQP176 LQS144 LBE192 29 - - - 30 21 18 G3 31 22 19 G4 32 23 20 G5 33 - - - 34 24 - G6 35 25 - H4 36 26 21 H2 37 27 22 J1 38 28 23 H3 39 40 29 30 24 25 H1 H5 41 31 26 H6 Document Number: 002-04988 Rev. *C Pin Name P5B FRCK0_1 TIOB5_1 MADATA27_0 P08 SIN14_0 TIOB12_0 INT17_0 MDQM0_0 P09 SOT14_0 (SDA14_0) TIOB13_0 INT18_0 MDQM1_0 P0A ADTG_1 SCK14_0 (SCL14_0) AIN2_1 MCLKOUT_0 P5C TIOA11_2 MADATA28_0 RTCCO_1 SUBOUT_1 P30 TIOA13_2 INT03_2 MDQM2_0 I2SDI0_0 P31 TIOB13_2 MDQM3_0 I2SCK0_0 P32 BIN2_1 INT19_0 S_DATA1_0 P33 FRCK0_0 ZIN2_1 S_DATA0_0 P34 IC03_0 INT00_1 S_CLK_0 VCC VSS P35 IC02_0 INT01_1 S_CMD_0 I/O Circuit Type Pin State Type E I E K E K L I E I E K E I L K L I L K - - L K Page 17 of 198 S6E2C3 Series Pin Number LQQ216 LQP176 LQS144 LBE192 42 32 27 J5 43 33 28 J4 44 34 29 J3 45 35 30 J2 46 36 31 K1 47 37 32 K2 48 38 33 K3 49 39 34 K4 Document Number: 002-04988 Rev. *C Pin Name P36 IC01_0 INT02_1 S_DATA3_0 P37 IC00_0 INT03_1 S_DATA2_0 P38 ADTG_2 DTTI0X_0 S_WP_0 P39 SIN2_1 RTO00_0 (PPG00_0) TIOA0_1 AIN3_1 INT16_1 S_CD_0 MAD24_0 P3A SOT2_1 (SDA2_1) RTO01_0 (PPG00_0) TIOA1_1 BIN3_1 INT17_1 MAD23_0 P3B SCK2_1 (SCL2_1) RTO02_0 (PPG02_0) TIOA2_1 ZIN3_1 INT18_1 MAD22_0 MNALE_0 P3C SIN13_0 RTO03_0 (PPG02_0) TIOA3_1 INT19_1 MAD21_0 MNCLE_0 P3D SOT13_0 (SDA13_0) RTO04_0 (PPG04_0) TIOA4_1 MAD20_0 MNWEX_0 I/O Circuit Type Pin State Type L K L K E I G K G K G K G K G I Page 18 of 198 S6E2C3 Series Pin Number LQQ216 LQP176 LQS144 LBE192 50 40 35 L1 51 41 - L2 52 42 - L3 53 43 - M2 54 55 44 45 36 37 M1 N1 56 46 38 N2 57 47 39 N3 58 48 40 M3 Document Number: 002-04988 Rev. *C Pin Name P3E SCK13_0 (SCL13_0) RTO05_0 (PPG04_0) TIOA5_1 MAD19_0 MNREX_0 P5D SIN10_1 TIOB11_2 INT01_2 MADATA29_0 I2SMCLK0_0 P5E SOT10_1 (SDA10_1) TIOA12_2 MADATA30_0 I2SDO0_0 P5F SCK10_1 (SCL10_1) TIOB12_2 MADATA31_0 I2SWS0_0 VSS VCC P40 SIN3_1 RTO10_0 (PPG10_0) TIOA0_0 AIN0_0 INT23_0 MCSX7_0 P41 SOT3_1 (SDA3_1) RTO11_0 (PPG10_0) TIOA1_0 BIN0_0 MCSX6_0 P42 SCK3_1 (SCL3_1) RTO12_0 (PPG12_0) TIOA2_0 ZIN0_0 MCSX5_0 I/O Circuit Type Pin State Type G I E K E I E I - - G K G I G I Page 19 of 198 S6E2C3 Series Pin Number LQQ216 LQP176 LQS144 LBE192 59 49 41 L4 60 50 42 M4 61 51 43 N4 62 63 64 52 53 54 44 45 46 P2 P3 P4 65 - - - 66 - - - 67 - - - 68 - - - 69 - - - 70 55 47 L5 71 56 48 M5 72 57 49 N5 73 58 50 P5 74 59 51 P6 Document Number: 002-04988 Rev. *C Pin Name P43 SIN15_0 RTO13_0 (PPG12_0) TIOA3_0 INT04_0 MCSX4_0 P44 SOT15_0 (SDA15_0) RTO14_0 (PPG14_0) TIOA4_0 MCSX3_0 P45 SCK15_0 (SCL15_0) RTO15_0 (PPG14_0) TIOA5_0 MCSX2_0 C VSS VCC P4A SIN12_1 AIN0_1 INT04_2 P4B SOT12_1 (SDA12_1) BIN0_1 P4C SCK12_1 (SCL12_1) ZIN0_1 P4D SCS72_1 INT05_2 P4E SCS73_1 P7D SCK1_1 (SCL1_1) DTTI1X_0 INT05_0 WKUP2 MCSX1_0 P7E ADTG_7 FRCK1_0 MCSX0_0 INITX P46 X0A P47 X1A I/O Circuit Type Pin State Type G K G I G I - - E K E I E I E K E I L Q L I B C P S Q T Page 20 of 198 S6E2C3 Series Pin Number LQQ216 LQP176 LQS144 LBE192 75 60 52 P8 76 61 53 N6 77 62 54 M6 78 63 - K5 79 64 - K6 80 65 55 L6 81 66 56 J6 82 67 57 L8 83 68 58 K8 84 69 59 J8 85 70 - N8 86 71 - M8 Document Number: 002-04988 Rev. *C Pin Name VBAT P48 VREGCTL P49 VWAKEUP PF0 SCS63_0 FRCK1_1 TIOA15_1 INT22_1 PF1 SCS62_0 TIOB15_1 INT23_1 P70 ADTG_8 SIN1_1 INT06_0 MRDY_0 P71 SOT1_1 (SDA1_1) MAD00_0 P72 SIN9_0 TIOB0_0 INT07_0 MAD01_0 P73 SOT9_0 (SDA9_0) TIOB1_0 MAD02_0 P74 SCK9_0 (SCL9_0) TIOB2_0 MAD03_0 PF2 RTO10_1 (PPG10_1) TIOA6_1 MRASX_0 PF3 RTO11_1 (PPG10_1) TIOB6_1 INT05_1 MCASX_0 I/O Circuit Type - Pin State Type O U O U E K E K I K E I E K E I E I L I L K - Page 21 of 198 S6E2C3 Series Pin Number LQQ216 LQP176 LQS144 LBE192 87 72 - N9 88 73 - P9 89 74 - M9 90 75 - L9 91 76 60 K9 92 77 61 P10 93 78 62 N10 94 - - - 95 - - - 96 79 63 L10 Document Number: 002-04988 Rev. *C Pin Name PF4 RTO12_1 (PPG12_1) TIOA7_1 INT06_1 MSDWEX_0 PF5 RTO13_1 (PPG12_1) TIOB7_1 INT07_1 MCSX8_0 PF6 RTO14_1 (PPG14_1) TIOA14_1 INT20_1 MSDCKE_0 PF7 RTO15_1 (PPG14_1) TIOB14_1 INT21_1 MSDCLK_0 P75 SIN8_0 TIOB3_0 AIN1_0 INT20_0 MAD04_0 P76 SOT8_0 (SDA8_0) TIOB4_0 BIN1_0 MAD05_0 P77 SCK8_0 (SCL8_0) TIOB5_0 ZIN1_0 MAD06_0 PF8 SCS70_1 DTTI1X_1 AIN1_1 PF9 SCS71_1 IC10_1 BIN1_1 P78 SIN6_0 IC10_0 INT21_0 MAD07_0 I/O Circuit Type Pin State Type L K L K L K L K E K E I E I E I E I E K Page 22 of 198 S6E2C3 Series Pin Number LQQ216 LQP176 LQS144 LBE192 97 80 64 K10 98 81 65 M10 99 82 66 N11 100 83 67 M11 101 - - - 102 - - - 103 - - - 104 84 68 N13 105 85 69 N12 Pin Name P79 SOT6_0 (SDA6_0) IC11_0 MAD08_0 P7A SCK6_0 (SCL6_0) IC12_0 MAD09_0 P7B DA1 SCS60_0 IC13_0 INT22_0 P7C DA0 SCS61_0 INT04_1 PFA SCK7_1 (SCL7_1) IC11_1 ZIN1_1 PFB SOT7_1 (SDA7_1) IC12_1 INT07_2 PFC SIN7_1 IC13_1 INT06_2 PE0 MD1 MD0 PE2 X0 PE3 X1 I/O Circuit Type Pin State Type L I L I R J R J E I E K E K C E J D A A A B 106 86 70 P12 107 87 71 P13 108 88 72 N14 VSS - - 109 89 73 M14 VCC - - 110 90 74 M13 AVCC - - 111 91 75 M12 AVSS - - 112 92 76 L13 AVRL - - 113 93 77 L12 AVRH - - L11 P10 AN00 SIN10_0 TIOA0_2 AIN0_2 INT08_0 F M 114 94 Document Number: 002-04988 Rev. *C 78 Page 23 of 198 S6E2C3 Series Pin Number LQQ216 LQP176 LQS144 LBE192 115 95 79 K13 116 96 80 K12 117 97 81 K14 118 98 82 K11 119 - - - 120 - - - 121 - - - 122 - - - 123 99 83 J13 124 100 84 J12 Document Number: 002-04988 Rev. *C Pin Name P11 AN01 SOT10_0 (SDA10_0) TIOB0_2 BIN0_2 P12 AN02 SCK10_0 (SCL10_0) TIOA1_2 ZIN0_2 P13 AN03 SIN6_1 INT25_1 P14 AN04 SOT6_1 (SDA6_1) PB8 ADTG_6 SCS63_1 INT08_2 TRACED8 PB9 SIN9_1 AIN2_2 INT09_2 TRACED9 PBA SOT9_1 (SDA9_1) BIN2_2 TRACED10 PBB SCK9_1 (SCL9_1) ZIN2_2 TRACED11 P15 AN05 SIN11_0 TIOB1_2 AIN1_2 INT09_0 P16 AN06 SOT11_0 (SDA11_0) TIOA2_2 BIN1_2 I/O Circuit Type Pin State Type F L F L F M F L E O E O E N E N F M F L Page 24 of 198 S6E2C3 Series Pin Number LQQ216 LQP176 LQS144 LBE192 125 101 85 J11 126 102 - J10 127 103 - J9 128 104 - H10 129 105 - J14 130 106 86 H9 131 107 87 H12 132 108 88 H14 133 109 89 G14 134 110 90 H13 Document Number: 002-04988 Rev. *C Pin Name P17 AN07 SCK11_0 (SCL11_0) TIOB2_2 ZIN1_2 PB0 AN16 SCK6_1 (SCL6_1) TIOA9_1 PB1 AN17 SCS60_1 TIOB9_1 INT08_1 PB2 AN18 SCS61_1 TIOA10_1 INT09_1 PB3 AN19 SCS62_1 TIOB10_1 P18 AN08 SIN2_0 TIOA3_2 INT10_0 P19 AN09 SOT2_0 (SDA2_0) TIOB3_2 INT24_1 TRACECLK P1A AN10 SCK2_0 (SCL2_0) TIOA4_2 TRACED0 P1B AN11 SIN12_0 TIOB4_2 INT11_0 TRACED1 P1C AN12 SOT12_0 (SDA12_0) TIOA5_2 TRACED2 I/O Circuit Type Pin State Type F L F L F M F M F L F M F O F N F O F N Page 25 of 198 S6E2C3 Series Pin Number LQQ216 LQP176 LQS144 LBE192 Pin Name I/O Circuit Type Pin State Type F N 135 111 91 H11 P1D AN13 SCK12_0 (SCL12_0) TIOB5_2 TRACED3 136 - - - VSS - - 137 - - - VCC - - F O F O F N F N F M F M F L F L 138 112 - G13 139 113 - F14 140 114 - G12 141 115 - G11 142 116 92 G10 143 117 93 G9 144 118 94 F10 145 119 95 F11 Document Number: 002-04988 Rev. *C PB4 AN20 SIN8_1 TIOA11_1 INT10_1 TRACED4 PB5 AN21 SOT8_1 (SDA8_1) TIOB11_1 INT11_1 TRACED5 PB6 AN22 SCK8_1 (SCL8_1) TIOA12_1 TRACED6 PB7 AN23 TIOB12_1 TRACED7 P1E AN14 TIOA8_1 INT26_1 MAD10_0 P1F AN15 RTS5_0 TIOB8_1 INT27_1 MAD11_0 P2A AN24 CTS5_0 MAD12_0 P29 AN25 SCK5_0 (SCL5_0) MAD13_0 Page 26 of 198 S6E2C3 Series Pin Number LQQ216 LQP176 LQS144 LBE192 146 120 96 F12 147 121 97 F13 148 - - - 149 - - - 150 - - - 151 - - - 152 122 98 E10 153 123 99 E11 154 124 100 E12 155 125 101 E13 156 126 102 D12 157 127 103 D13 Document Number: 002-04988 Rev. *C Pin Name P28 AN26 SOT5_0 (SDA5_0) MAD14_0 P27 AN27 SIN5_0 INT24_0 MAD15_0 PBC TRACED12 PBD SCK0_1 (SCL0_1) AIN3_2 INT10_2 TRACED13 PBE SOT0_1 (SDA0_1) BIN3_2 TRACED14 PBF SIN0_1 ZIN3_2 INT11_2 TRACED15 P26 MAD16_0 P25 AN28 INT25_0 MAD17_0 P24 AN29 TIOA13_1 MAD18_0 P23 UHCONX1 AN30 SCK0_0 (SCL0_0) TIOB13_1 P22 AN31 SOT0_0 (SDA0_0) INT26_0 P21 ADTG_4 SIN0_0 INT27_0 CROUT_0 I/O Circuit Type Pin State Type F L F M E N E O E N E O E I F M F L F L F M I K Page 27 of 198 S6E2C3 Series Pin Number Pin Name I/O Circuit Type Pin State Type LQQ216 LQP176 LQS144 LBE192 158 128 104 C13 P20 NMIX WKUP0 I F 159 129 105 E14 USBVCC1 - - H R H R P82 UDM1 P83 UDP1 160 130 106 D14 161 131 107 C14 162 132 108 B14 VSS - - 163 133 109 A13 VCC - - E G E G E G E G E G S K S K S K S K S I S I S K S K K V 164 134 110 B13 165 135 111 A12 166 136 112 C12 167 137 113 B12 168 138 114 B11 169 139 - C11 170 140 - D11 171 141 - B10 172 142 - C10 173 143 - D10 174 144 - B9 175 - - - 176 - - - 177 145 115 C9 Document Number: 002-04988 Rev. *C P00 TRSTX P01 TCK SWCLK P02 TDI P03 TMS SWDIO P04 TDO SWO P90 INT12_1 Q_IO3_0 P91 SIN5_1 INT13_1 Q_IO2_0 P92 SOT5_1 (SDA5_1) INT14_1 Q_IO1_0 P93 SCK5_1 (SCL5_1) INT15_1 Q_IO0_0 P94 CTS5_1 Q_SCK_0 P95 RTS5_1 Q_CS0_0 P96 INT12_2 Q_CS1_0 P97 INT13_2 Q_CS2_0 PC0 Page 28 of 198 S6E2C3 Series Pin Number Pin Name I/O Circuit Type Pin State Type K V K V K V K V K V K V E W K V K V LQQ216 LQP176 LQS144 LBE192 178 146 116 B8 179 147 117 D9 180 148 118 E9 181 149 119 F9 182 150 120 C8 183 151 121 D8 184 152 122 E8 185 153 123 A10 186 154 124 F8 PC5 TIOB14_0 PC6 TIOA14_0 PC7 INT13_0 CROUT_1 PC8 PC9 TIOB15_0 187 155 125 B7 PCA TIOA15_0 K V 188 156 126 A9 VCC - - 189 157 127 A8 - - 190 158 128 A7 L W 191 159 129 C7 K V 192 160 130 A6 VSS PCB INT28_0 PCC PCD SOT4_1 (SDA4_1) INT14_0 L W 193 161 131 D7 L W 194 162 132 E7 L W 195 163 133 F7 L W 196 164 134 B6 L W C6 PD2 CTS4_1 FRCK2_1 L V D6 P6E ADTG_5 SCK4_1 (SCL4_1) IC23_1 INT29_0 E W 197 198 165 166 135 136 Document Number: 002-04988 Rev. *C PC1 TIOB6_0 PC2 TIOA6_0 PC3 TIOB7_0 PC4 TIOA7_0 PCE SIN4_1 INT15_0 PCF RTS4_1 INT12_0 PD0 INT30_1 PD1 INT31_1 Page 29 of 198 S6E2C3 Series Pin Number LQQ216 LQP176 LQS144 LBE192 199 - - - 200 - - - 201 - - - 202 - - - 203 - - - 204 - - - 205 - - - 206 - - - 207 167 - E6 208 168 - B5 209 169 137 C5 Document Number: 002-04988 Rev. *C Pin Name P6D SCK14_1 (SCL14_1) IC22_1 TIOB6_2 P6C SOT14_1 (SDA14_1) IC21_1 TIOA6_2 P6B SIN14_1 IC20_1 TIOB7_2 INT14_2 P6A DTTI2X_1 TIOA7_2 P69 RTO20_1 (PPG20_1) TIOB14_2 P68 SCK13_1 (SCL13_0) RTO21_1 (PPG20_1) TIOA14_2 P67 SOT13_1 (SDA13_1) RTO22_1 (PPG22_1) TIOB15_2 P66 SIN13_1 RTO23_1 (PPG22_1) TIOA15_2 INT15_2 P65 RTO24_1 (PPG24_1) INT28_1 P64 CTS4_0 RTO25_1 (PPG24_1) INT29_1 P63 ADTG_3 RTS4_0 INT30_0 MOEX_0 I/O Circuit Type Pin State Type E I E I E K E I E I E I E I E K E K I K L K Page 30 of 198 S6E2C3 Series Pin Number LQQ216 LQP176 LQS144 LBE192 210 170 138 B4 211 171 139 C4 212 172 140 B3 213 173 141 A4 Pin Name P62 SCK4_0 (SCL4_0) MWEX_0 P61 UHCONX0 SOT4_0 (SDA4_0) MALE_0 RTCCO_0 SUBOUT_0 P60 SIN4_0 INT31_0 WKUP3 USBVCC0 P80 UDM0 P81 UDP0 I/O Circuit Type Pin State Type L I L I I Q - - H R H R 214 174 142 A3 215 175 143 A2 216 176 144 B1 - - - - - E1 - - - - - G1 - - - - - P7 - - - - - P11 - - - - - L14 - - - - - A11 - - - - - A5 - - - - - N7 - - - - - M7 - - - - - L7 - - - - - K7 - - - - - J7 - - -- - - G7 - - - - - H7 - - - - - H8 - - - - - G8 - - Document Number: 002-04988 Rev. *C VSS Page 31 of 198 S6E2C3 Series Signal Descriptions The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function register (EPFR) to select the pin. Module Pin Name A/D converter ADTG_0 ADTG_1 ADTG_2 ADTG_3 ADTG_4 ADTG_5 ADTG_6 ADTG_7 ADTG_8 AN00 AN01 AN02 AN03 AN04 AN05 AN06 AN07 AN08 AN09 AN10 AN11 AN12 AN13 AN14 AN15 AN16 AN17 AN18 AN19 AN20 AN21 AN22 AN23 AN24 AN25 AN26 AN27 AN28 AN29 AN30 AN31 Function A/D converter external trigger input pin A/D converter analog input pin. ANxx describes A/D converter ch xx. Document Number: 002-04988 Rev. *C LQQ 216 24 32 44 209 157 198 119 71 80 114 115 116 117 118 123 124 125 130 131 132 133 134 135 142 143 126 127 128 129 138 139 140 141 144 145 146 147 153 154 155 156 Pin Number LQP LQS 176 144 19 16 23 20 34 29 169 137 127 103 166 136 56 48 65 55 94 78 95 79 96 80 97 81 98 82 99 83 100 84 101 85 106 86 107 87 108 88 109 89 110 90 111 91 116 92 117 93 102 103 104 105 112 113 114 115 118 94 119 95 120 96 121 97 123 99 124 100 125 101 126 102 LBE 192 F6 G5 J3 C5 D13 D6 M5 L6 L11 K13 K12 K14 K11 J13 J12 J11 H9 H12 H14 G14 H13 H11 G10 G9 J10 J9 H10 J14 G13 F14 G12 G11 F10 F11 F12 F13 E11 E12 E13 D12 Page 32 of 198 S6E2C3 Series Module Base Timer 0 Base Timer 1 Base Timer 2 Base Timer 3 Pin Name TIOA0_0 TIOA0_1 TIOA0_2 TIOB0_0 TIOB0_1 TIOB0_2 TIOA1_0 TIOA1_1 TIOA1_2 TIOB1_0 TIOB1_1 TIOB1_2 TIOA2_0 TIOA2_1 TIOA2_2 TIOB2_0 TIOB2_1 TIOB2_2 TIOA3_0 TIOA3_1 TIOA3_2 TIOB3_0 TIOB3_1 TIOB3_2 TIOA4_0 TIOA4_1 Base Timer 4 Function Base Timer ch 0 TIOA pin Base Timer ch 0 TIOB pin Base Timer ch 1 TIOA pin Base Timer ch 1 TIOB pin Base Timer ch 2 TIOA pin Base Timer ch 2 TIOB pin Base Timer ch 3 TIOA pin Base Timer ch 3 TIOB pin Base Timer ch 4 TIOA pin LBE 192 N2 J2 L11 L8 K13 N3 K1 K12 K8 J13 M3 K2 J12 J8 J11 L4 K3 H9 K9 H12 M4 39 34 K4 TIOA4_2 132 108 88 H14 TIOB4_0 92 77 61 P10 28 - - - 133 109 89 G14 61 51 43 N4 50 40 35 L1 TIOA5_2 134 110 90 H13 TIOB5_0 93 78 62 N10 29 - - - TIOB5_2 135 111 91 H11 TIOA6_0 179 147 117 D9 85 70 - N8 Base Timer ch 4 TIOB pin TIOB4_2 TIOA5_0 TIOA5_1 TIOB5_1 TIOA6_1 Base Timer 6 Pin Number LQP LQS 176 144 46 38 35 30 94 78 67 57 95 79 47 39 36 31 96 80 68 58 99 83 48 40 37 32 100 84 69 59 101 85 49 41 38 33 106 86 76 60 107 87 50 42 49 TIOB4_1 Base Timer 5 LQQ 216 56 45 114 82 21 115 57 46 116 83 22 123 58 47 124 84 26 125 59 48 130 91 27 131 60 Base Timer ch 5 TIOA pin Base Timer ch 5 TIOB pin Base Timer ch 6 TIOA pin TIOA6_2 200 - - - TIOB6_0 178 146 116 B8 86 71 - M8 199 - - - TIOB6_1 Base Timer ch 6 TIOB pin TIOB6_2 Document Number: 002-04988 Rev. *C Page 33 of 198 S6E2C3 Series Module LQQ 216 Pin Number LQP LQS 176 144 181 149 119 LBE 192 F9 87 72 - N9 TIOA7_2 202 - - - TIOB7_0 180 148 118 E9 Pin Name Function TIOA7_0 TIOA7_1 Base Timer 7 TIOB7_1 Base Timer ch 7 TIOB pin 88 73 - P9 TIOB7_2 201 - - - TIOA8_0 2 2 2 B2 142 116 92 G10 TIOA8_2 10 10 - E2 TIOB8_0 18 17 14 F4 143 117 93 G9 11 11 - E3 TIOA8_1 Base Timer 8 Base Timer ch 7 TIOA pin TIOB8_1 Base Timer ch 8 TIOA pin Base Timer ch 8 TIOB pin TIOB8_2 TIOA9_0 3 3 3 C2 126 102 - J10 TIOA9_2 12 12 - E4 TIOB9_0 23 18 15 F5 127 103 - J9 TIOB9_2 13 - - - TIOA10_0 4 4 4 C3 128 104 - H10 TIOA9_1 Base Timer 9 TIOB9_1 TIOA10_1 Base Timer 10 Base Timer ch 10 TIOA pin 19 - - - TIOB10_0 24 19 16 F6 129 105 - J14 TIOB10_2 20 - - - TIOA11_0 5 5 5 D5 138 112 - G13 TIOA11_2 33 - - - TIOB11_0 25 20 17 G2 TIOA11_1 TIOB11_1 Base Timer ch 10 TIOB pin Base Timer ch 11 の TIOA pin Base Timer ch 11 TIOB pin 139 113 - F14 TIOB11_2 51 41 - L2 TIOA12_0 6 6 6 D2 140 114 - G12 TIOA12_2 52 42 - L3 TIOB12_0 30 21 18 G3 141 115 - G11 53 43 - M2 TIOA12_1 Base Timer 12 Base Timer ch 9 TIOB pin TIOA10_2 TIOB10_1 Base Timer 11 Base Timer ch 9 TIOA pin TIOB12_1 Base Timer ch 12 TIOA pin Base Timer ch 12 TIOB pin TIOB12_2 Document Number: 002-04988 Rev. *C Page 34 of 198 S6E2C3 Series Module Pin Name Function 7 7 7 154 124 100 E12 TIOA13_2 34 24 - G6 TIOB13_0 31 22 19 G4 155 125 101 E13 TIOA13_1 TIOB13_1 Base Timer ch 13 TIOB pin 35 25 - H4 TIOA14_0 183 151 121 D8 89 74 - M9 TIOA14_2 204 - - - TIOB14_0 182 150 120 C8 90 75 - L9 TIOB14_2 203 - - - TIOA15_0 187 155 125 B7 78 63 - K5 TIOA15_2 206 - - - TIOB15_0 186 154 124 F8 TIOB14_1 TIOA15_1 Base Timer 15 Base Timer ch 13 TIOA pin TIOB13_2 TIOA14_1 Base Timer 14 TIOB15_1 Base Timer ch 14 TIOA pin Base Timer ch 14 TIOB pin Base Timer ch 15 TIOA pin Base timer ch 15 TIOB pin TIOB15_2 79 64 - K6 205 - - - 165 135 111 A12 167 137 113 B12 168 138 114 B11 SWO Serial wire debug interface clock input pin Serial wire debug interface data input/ output pin Serial wire viewer output pin TCK JTAG test clock input pin 165 135 111 A12 TDI JTAG test data input pin 166 136 112 C12 TDO JTAG debug data output pin 168 138 114 B11 TMS JTAG test mode state input/output pin 167 137 113 B12 Trace CLK output pin of ETM/HTM 131 107 87 H12 132 108 88 H14 133 109 89 G14 134 110 90 H13 TRACED3 135 111 91 H11 TRACED4 138 112 - G13 TRACED5 139 113 - F14 TRACED6 140 114 - G12 141 115 - G11 119 - - - TRACED9 120 - - - TRACED10 121 - - - TRACED11 122 - - - SWCLK SWDIO TRACECLK TRACED0 Debugger Pin Number LQP LQS 176 144 LBE 192 D1 TIOA13_0 Base Timer 13 LQQ 216 TRACED1 TRACED2 TRACED7 TRACED8 Trace data output pin of ETM/ Trace data output pin of HTM Trace data output pin of HTM Document Number: 002-04988 Rev. *C Page 35 of 198 S6E2C3 Series Module Pin Name Function 148 - - 149 - - - 150 - - - 151 - - - 164 134 110 MAD00_0 81 66 56 B13 J6 MAD01_0 82 67 57 L8 MAD02_0 83 68 58 K8 MAD03_0 84 69 59 J8 MAD04_0 91 76 60 K9 MAD05_0 92 77 61 P10 TRACED13 TRACED14 Trace data output pin of HTM TRACED15 TRSTX JTAG test reset Input pin MAD06_0 93 78 62 N10 MAD07_0 96 79 63 L10 MAD08_0 97 80 64 K10 MAD09_0 98 81 65 M10 MAD10_0 142 116 92 G10 MAD11_0 143 117 93 G9 144 118 94 F10 145 119 95 F11 MAD12_0 External bus interface address bus MAD13_0 External bus Pin Number LQP LQS 176 144 LBE 192 - TRACED12 Debugger LQQ 216 MAD14_0 146 120 96 F12 MAD15_0 147 121 97 F13 MAD16_0 152 122 98 E10 MAD17_0 153 123 99 E11 MAD18_0 154 124 100 E12 MAD19_0 50 40 35 L1 MAD20_0 49 39 34 K4 MAD21_0 48 38 33 K3 MAD22_0 47 37 32 K2 MAD23_0 46 36 31 K1 MAD24_0 45 35 30 J2 MCSX0_0 71 56 48 M5 MCSX1_0 70 55 47 L5 MCSX2_0 61 51 43 N4 60 50 42 M4 59 49 41 L4 MCSX5_0 58 48 40 M3 MCSX6_0 57 47 39 N3 MCSX7_0 56 46 38 N2 MCSX8_0 88 73 - P9 MCSX3_0 MCSX4_0 External bus interface chip select output pin Document Number: 002-04988 Rev. *C Page 36 of 198 S6E2C3 Series Module Pin Name LQQ 216 Pin Number LQP LQS 176 144 MADATA00_0 2 2 2 LBE 192 B2 MADATA01_0 3 3 3 C2 MADATA02_0 4 4 4 C3 MADATA03_0 5 5 5 D5 MADATA04_0 6 6 6 D2 MADATA05_0 7 7 7 D1 MADATA06_0 8 8 8 D3 MADATA07_0 9 9 9 D4 MADATA08_0 14 13 10 E5 MADATA09_0 15 14 11 F1 MADATA10_0 16 15 12 F2 MADATA11_0 17 16 13 F3 MADATA12_0 18 17 14 F4 MADATA13_0 23 18 15 F5 MADATA14_0 24 19 16 F6 25 20 17 G2 10 - - - MADATA17_0 11 - - - MADATA18_0 12 - - - MADATA19_0 13 - - - MADATA20_0 19 - - - MADATA21_0 20 - - - MADATA22_0 21 - - - MADATA23_0 22 - - - MADATA24_0 26 - - - MADATA25_0 27 - - - MADATA26_0 28 - - - MADATA27_0 29 - - - MADATA28_0 33 - - - MADATA29_0 51 - - - MADATA30_0 52 - - - MADATA31_0 53 - - - MDQM0_0 30 21 18 G3 31 22 19 G4 34 - - - 35 - - - 211 171 139 C4 80 65 55 L6 MADATA15_0 MADATA16_0 External bus Function MDQM1_0 MDQM2_0 External bus interface data bus (address/data multiplex bus) External bus interface byte mask signal output pin MDQM3_0 MALE_0 MRDY_0 External bus interface address latch enable output signal for multiplex External bus interface external RDY input signal Document Number: 002-04988 Rev. *C Page 37 of 198 S6E2C3 Series Module Pin Name MCLKOUT_0 MNALE_0 MNCLE_0 MNREX_0 MNWEX_0 External bus MOEX_0 MWEX_0 MSDCLK_0 MSDCKE_0 MRASX_0 MCASX_0 MSDWEX_0 Function External bus interface external clock output pin External bus interface ALE signal to control NAND flash output pin External bus interface CLE signal to control NAND flash output pin External bus interface read enable signal to control NAND flash External bus interface write enable signal to control NAND flash External bus interface read enable signal for SRAM External bus interface write enable signal for SRAM SDRAM interface SDRAM clock output pin SDRAM interface SDRAM clock enable pin SDRAM interface SDRAM column active strobe pin SDRAM interface SDRAM row active strobe pin SDRAM interface SDRAM write enable pin INT00_0 INT00_1 Pin Number LQP LQS 176 144 LBE 192 32 23 20 G5 47 37 32 K2 48 38 33 K3 50 40 35 L1 49 39 34 K4 209 169 137 C5 210 170 138 B4 90 75 - L9 89 74 - M9 85 70 - N8 86 71 - M8 87 72 - N9 2 2 2 B2 38 28 23 H3 INT00_2 19 - - - INT01_0 7 7 7 D1 41 31 26 H6 INT01_2 51 41 - L2 INT02_0 14 13 10 E5 42 32 27 J5 26 - - - 17 16 13 F3 43 33 28 J4 INT03_2 34 24 - G6 INT04_0 59 49 41 L4 100 83 67 M11 INT04_2 65 - - - INT05_0 70 55 47 L5 86 71 - M8 68 - - - INT01_1 INT02_1 External interrupt External interrupt request 00 input pin LQQ 216 External interrupt request 01 input pin External interrupt request 02 input pin INT02_2 INT03_0 INT03_1 INT04_1 INT05_1 External interrupt request 03 input pin External interrupt request 04 input pin External interrupt request 05 input pin INT05_2 Document Number: 002-04988 Rev. *C Page 38 of 198 S6E2C3 Series Module Pin Name Function Pin Number LQP LQS 176 144 80 65 55 LBE 192 L6 87 72 - N9 INT06_2 103 - - - INT07_0 82 67 57 L8 INT06_0 INT06_1 INT07_1 External interrupt request 06 input pin External interrupt request 07 input pin 88 73 - P9 INT07_2 102 - - - INT08_0 114 94 78 L11 127 103 - J9 INT08_2 119 - - - INT09_0 123 99 83 J13 128 104 - H10 120 - - - 130 106 86 H9 138 112 - G13 INT10_2 149 - - - INT11_0 133 109 89 G14 139 113 - F14 INT11_2 151 - - - INT12_0 194 162 132 E7 169 139 - C11 INT08_1 INT09_1 External interrupt request 08 input pin External interrupt request 09 input pin INT09_2 INT10_0 INT10_1 INT11_1 External interrupt LQQ 216 INT12_1 External interrupt request 10 input pin External interrupt request 11 input pin External interrupt request 12 input pin INT12_2 175 - - - INT13_0 184 152 122 E8 170 140 - D11 INT13_2 176 - - - INT14_0 192 160 130 A6 171 141 - B10 INT14_2 201 - - - INT15_0 193 161 131 D7 172 142 - C10 206 - - - 25 20 17 G2 45 35 30 J2 30 21 18 G3 46 36 31 K1 31 22 19 G4 47 37 32 K2 36 26 21 H2 48 38 33 K3 INT13_1 INT14_1 INT15_1 External interrupt request 13 input pin External interrupt request 14 input pin External interrupt request 15 input pin INT15_2 INT16_0 INT16_1 INT17_0 INT17_1 INT18_0 INT18_1 INT19_0 INT19_1 External interrupt request 16 input pin External interrupt request 17 input pin External interrupt request 18 input pin External interrupt request 19 input pin Document Number: 002-04988 Rev. *C Page 39 of 198 S6E2C3 Series Module Pin Name INT20_0 INT20_1 INT21_0 INT21_1 INT22_0 INT22_1 INT23_0 INT23_1 INT24_0 INT24_1 INT25_0 INT25_1 External interrupt INT26_0 INT26_1 INT27_0 INT27_1 INT28_0 INT28_1 INT29_0 INT29_1 INT30_0 INT30_1 INT31_0 INT31_1 NMIX Function External interrupt request 20 input pin External interrupt request 21 input pin External interrupt request 22 input pin External interrupt request 23 input pin External interrupt request 24 input pin External interrupt request 25 input pin External interrupt request 26 input pin External interrupt request 27 input pin External interrupt request 28 input pin External interrupt request 29 input pin External interrupt request 30 input pin External interrupt request 31 input pin Non-maskable interrupt input pin Document Number: 002-04988 Rev. *C LQQ 216 Pin Number LQP LQS 176 144 91 76 60 LBE 192 K9 89 74 - M9 96 79 63 L10 90 75 - L9 99 82 66 N11 78 63 - K5 56 46 38 N2 79 64 - K6 147 121 97 F13 131 107 87 H12 153 123 99 E11 117 97 81 K14 156 126 102 D12 142 116 92 G10 157 127 103 D13 143 117 93 G9 190 158 128 A7 207 167 - E6 198 166 136 D6 208 168 - B5 209 169 137 C5 195 163 133 F7 212 172 140 B3 196 164 134 B6 158 128 104 C13 Page 40 of 198 S6E2C3 Series Module LQQ 216 Pin Number LQP LQS 176 144 P00 164 134 110 LBE 192 B13 P01 165 135 111 A12 P02 166 136 112 C12 167 137 113 B12 Pin Name P03 P04 General-purpose I/O port 0 168 138 114 B11 P08 30 21 18 G3 P09 31 22 19 G4 P0A 32 23 20 G5 P10 114 94 78 L11 P11 115 95 79 K13 P12 116 96 80 K12 P13 117 97 81 K14 P14 118 98 82 K11 P15 123 99 83 J13 P16 124 100 84 J12 125 101 85 J11 130 106 86 H9 P19 131 107 87 H12 P1A 132 108 88 H14 P1B 133 109 89 G14 P1C 134 110 90 H13 P1D 135 111 91 H11 P1E 142 116 92 G10 P1F 143 117 93 G9 P20 158 128 104 C13 P21 157 127 103 D13 P22 156 126 102 D12 P23 155 125 101 E13 154 124 100 E12 153 123 99 E11 P26 152 122 98 E10 P27 147 121 97 F13 P28 146 120 96 F12 P29 145 119 95 F11 P2A 144 118 94 F10 P17 P18 GPIO Function General-purpose I/O port 1 P24 P25 General-purpose I/O port 2 Document Number: 002-04988 Rev. *C Page 41 of 198 S6E2C3 Series Module Pin Name LQQ 216 Pin Number LQP LQS 176 144 P30 34 24 - LBE 192 G6 P31 35 25 - H4 P32 36 26 21 H2 P33 37 27 22 J1 P34 38 28 23 H3 P35 41 31 26 H6 P36 42 32 27 J5 43 33 28 J4 P38 44 34 29 J3 P39 45 35 30 J2 P3A 46 36 31 K1 P3B 47 37 32 K2 P3C 48 38 33 K3 P3D 49 39 34 K4 P3E 50 40 35 L1 P40 56 46 38 N2 P41 57 47 39 N3 P42 58 48 40 M3 P43 59 49 41 L4 P44 60 50 42 M4 P45 61 51 43 N4 P46 73 58 50 P5 74 59 51 P6 P48 76 61 53 N6 P49 77 62 54 M6 P4A 65 - - - P4B 66 - - - P4C 67 - - - P4D 68 - - - P4E 69 - - - P37 GPIO Function P47 General-purpose I/O port 3 General-purpose I/O port 4 Document Number: 002-04988 Rev. *C Page 42 of 198 S6E2C3 Series Module Pin Name LQQ 216 Pin Number LQP LQS 176 144 P50 10 10 - LBE 192 E2 P51 11 11 - E3 P52 12 12 - E4 P53 13 - - - P54 19 - - - P55 20 - - - P56 21 - - - 22 - - - 26 - - - P59 27 - - - P5A 28 - - - P5B 29 - - - P5C 33 - - - P5D 51 41 - L2 P5E 52 42 - L3 P5F 53 43 - M2 P60 212 172 140 B3 P61 211 171 139 C4 P62 210 170 138 B4 P63 209 169 137 C5 P64 208 168 - B5 P65 207 167 - E6 P66 206 - - - 205 - - - P68 204 - - - P69 203 - - - P6A 202 - - - P6B 201 - - - P6C 200 - - - P6D 199 - - - P6E 198 166 136 D6 P57 P58 GPIO Function P67 General-purpose I/O port 5 General-purpose I/O port 6 Document Number: 002-04988 Rev. *C Page 43 of 198 S6E2C3 Series Module Pin Name LQQ 216 Pin Number LQP LQS 176 144 P70 80 65 55 LBE 192 L6 P71 81 66 56 J6 P72 82 67 57 L8 P73 83 68 58 K8 P74 84 69 59 J8 P75 91 76 60 K9 P76 92 77 61 P10 93 78 62 N10 P78 96 79 63 L10 P79 97 80 64 K10 P7A 98 81 65 M10 P7B 99 82 66 N11 P7C 100 83 67 M11 P7D 70 55 47 L5 P7E 71 56 48 M5 P80 214 174 142 A3 215 175 143 A2 160 130 106 D14 P83 161 131 107 C14 P90 169 139 - C11 P91 170 140 - D11 P92 171 141 - B10 172 142 - C10 173 143 - D10 P95 174 144 - B9 P96 175 - - - P97 176 - - - P77 GPIO Function P81 P82 P93 P94 General-purpose I/O port 7 General-purpose I/O port 8 General-purpose I/O port 9 Document Number: 002-04988 Rev. *C Page 44 of 198 S6E2C3 Series Module Pin Name LQQ 216 Pin Number LQP LQS 176 144 PA0 2 2 2 LBE 192 B2 PA1 3 3 3 C2 PA2 4 4 4 C3 PA3 5 5 5 D5 PA4 6 6 6 D2 PA5 7 7 7 D1 PA6 8 8 8 D3 9 9 9 D4 14 13 10 E5 PA9 15 14 11 F1 PAA 16 15 12 F2 PAB 17 16 13 F3 PAC 18 17 14 F4 PAD 23 18 15 F5 PAE 24 19 16 F6 PAF 25 20 17 G2 PB0 126 102 - J10 PB1 127 103 - J9 PB2 128 104 - H10 PB3 129 105 - J14 PB4 138 112 - G13 PB5 139 113 - F14 PB6 140 114 - G12 141 115 - G11 119 - - - PB9 120 - - - PBA 121 - - - PBB 122 - - - PBC 148 - - - PBD 149 - - - PBE 150 - - - PBF 151 - - - PA7 PA8 GPIO Function PB7 PB8 General-purpose I/O port A General-purpose I/O port B Document Number: 002-04988 Rev. *C Page 45 of 198 S6E2C3 Series Module LQQ 216 Pin Number LQP LQS 176 144 PC0 177 145 115 LBE 192 C9 PC1 178 146 116 B8 PC2 179 147 117 D9 PC3 180 148 118 E9 PC4 181 149 119 F9 PC5 182 150 120 C8 PC6 183 151 121 D8 184 152 122 E8 185 153 123 A10 PC9 186 154 124 F8 PCA 187 155 125 B7 PCB 190 158 128 A7 PCC 191 159 129 C7 PCD 192 160 130 A6 PCE 193 161 131 D7 PCF 194 162 132 E7 PD0 195 163 133 F7 196 164 134 B6 PD2 197 165 135 C6 PE0 104 84 68 N13 Pin Name PC7 PC8 GPIO PD1 PE2 Function General-purpose I/O port C General-purpose I/O port D General-purpose I/O port E 106 86 70 P12 PE3 107 87 71 P13 PF0 78 63 - K5 PF1 79 64 - K6 PF2 85 70 - N8 PF3 86 71 - M8 PF4 87 72 - N9 PF5 88 73 - P9 PF6 General-purpose I/O port F 89 74 - M9 PF7 90 75 - L9 PF8 94 - - - PF9 95 - - - PFA 101 - - - PFB 102 - - - PFC 103 - - - Document Number: 002-04988 Rev. *C Page 46 of 198 S6E2C3 Series Module Pin Name Function LQQ 216 Pin Number LQP LQS 176 144 SIN0_0 Multi-function serial interface ch 0 input pin 157 127 103 LBE 192 D13 151 - - - 156 126 102 D12 150 - - - 155 125 101 E13 149 - - - SIN0_1 SOT0_0 (SDA0_0) MultiFunction Serial 0 SOT0_1 (SDA0_1) SCK0_0 (SCL0_0) SCK0_1 (SCL0_1) SIN1_0 SIN1_1 SOT1_0 (SDA1_0) MultiFunction Serial 1 Multi-function serial interface ch 1 input pin 7 7 7 D1 80 65 55 L6 Multi-function serial interface ch 1 output pin. 8 8 8 D3 81 66 56 J6 9 9 9 D4 70 55 47 L5 130 106 86 H9 45 35 30 J2 131 107 87 H12 46 36 31 K1 132 108 88 H14 47 37 32 K2 This pin operates as SOT1 when it is used in SOT1_1 (SDA1_1) a UART/CSIO/LIN (operation modes 0 to 3) and as SDA1 when it is used in an I2C (operation mode 4). SCK1_0 (SCL1_0) SCK1_1 (SCL1_1) SIN2_0 SIN2_1 SOT2_0 (SDA2_0) MultiFunction Serial 2 Multi-function serial interface ch 0 output pin This pin operates as SOT0 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA0 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 0 clock I/O pin. This pin operates as SCK0 when it is used in a CSIO (operation mode 2) and as SCL0 when it is used in an I2C (operation mode 4) SOT2_1 (SDA2_1) SCK2_0 (SCL2_0) SCK2_1 (SCL2_1) Multi-function serial interface ch 1 clock I/O pin. This pin operates as SCK1 when it is used in a CSIO (operation mode 2) and as SCL1 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 2 input pin Multi-function serial interface ch 2 output pin. This pin operates as SOT2 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA2 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 2 clock I/O pin. This pin operates as SCK2 when it is used in a CSIO (operation mode 2) and as SCL2 when it is used in an I2C (operation mode 4). Document Number: 002-04988 Rev. *C Page 47 of 198 S6E2C3 Series Module Function LQQ 216 SIN3_0 Multi-function serial interface ch 3 input pin 25 20 17 LBE 192 G2 56 46 38 N2 24 19 16 F6 57 47 39 N3 23 18 15 F5 58 48 40 M3 212 172 140 B3 193 161 131 D7 211 171 139 C4 192 160 130 A6 210 170 138 B4 198 166 136 D6 Multi-function serial interface ch 4 CTS input pin 208 168 - B5 197 165 135 C6 Multi-function serial interface ch 4 RTS output pin 209 169 137 C5 194 162 132 E7 SIN3_1 SOT3_0 (SDA3_0) MultiFunction Serial 3 SOT3_1 (SDA3_1) SCK3_0 (SCL3_0) SCK3_1 (SCL3_1) SIN4_0 SIN4_1 SOT4_0 (SDA4_0) SOT4_1 (SDA4_1) MultiFunction Serial 4 Pin Number LQP LQS 176 144 Pin Name SCK4_0 (SCL4_0) SCK4_1 (SCL4_1) CTS4_0 CTS4_1 RTS4_0 RTS4_1 Multi-function serial interface ch 3 output pin. This pin operates as SOT3 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA3 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 3 clock I/O pin. This pin operates as SCK3 when it is used in a CSIO (operation modes 2) and as SCL3 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 4 input pin Multi-function serial interface ch 4 output pin. This pin operates as SOT4 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA4 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 4 clock I/O pin. This pin operates as SCK4 when it is used in a CSIO (operation mode 2) and as SCL4 when it is used in an I2C (operation mode 4). Document Number: 002-04988 Rev. *C Page 48 of 198 S6E2C3 Series Module Pin Name Function LQQ 216 Pin Number LQP LQS 176 144 SIN5_0 Multi-function serial interface ch 5 input pin 147 121 97 LBE 192 F13 170 140 - D11 146 120 96 F12 171 141 - B10 145 119 95 F11 172 142 - C10 Multi-function serial interface ch 5 CTS input pin 144 118 94 F10 173 143 - D10 Multi-function serial interface ch 5 RTS output pin 143 117 93 G9 174 144 - B9 SIN5_1 SOT5_0 (SDA5_0) SOT5_1 (SDA5_1) MultiFunction Serial 5 SCK5_0 (SCL5_0) SCK5_1 (SCL5_1) CTS5_0 CTS5_1 RTS5_0 RTS5_1 SIN6_0 SIN6_1 SOT6_0 (SDA6_0) SOT6_1 (SDA6_1) MultiFunction Serial 6 SCK6_0 (SCL6_0) SCK6_1 (SCL6_1) SCS60_0 SCS60_1 SCS61_0 SCS61_1 SCS62_0 Multi-function serial interface ch 5 output pin. This pin operates as SOT5 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA5 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 5 clock I/O pin. This pin operates as SCK5 when it is used in a CSIO (operation mode 2) and as SCL5 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 6 input pin Multi-function serial interface ch 6 output pin. This pin operates as SOT6 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA6 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 6 clock I/O pin. This pin operates as SCK6 when it is used in a CSIO (operation mode 2) and as SCL6 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 6 chip select 0 input/output pin Multi-function serial interface ch 6 chip select1 input/output pin 96 79 63 L10 117 97 81 K14 97 80 64 K10 118 98 82 K11 98 81 65 M10 126 102 - J10 99 127 100 82 103 83 66 67 N11 J9 M11 128 104 - H10 Multi-function serial interface ch 6 chip select2 input/output pin 79 64 - K6 SCS62_1 129 105 - J14 SCS63_0 SCS63_1 Multi-function serial interface ch 6 chip select3 input/output pin 78 119 63 - - K5 - Document Number: 002-04988 Rev. *C Page 49 of 198 S6E2C3 Series Module Pin Name Function SIN7_0 SIN7_1 SOT7_0 (SDA7_0) Multi-function serial interface ch 7 input pin Multi-function serial interface ch 7 output pin. This pin operates as SOT7 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA7 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 7 clock I/O pin. This pin operates as SCK7 when it is used in a CSIO (operation mode 2) and as SCL7 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 7 chip select 0 input/output pin SOT7_1 (SDA7_1) MultiFunction Serial 7 SCK7_0 (SCL7_0) SCK7_1 (SCL7_1) SCS70_0 SCS70_1 SCS71_0 SCS71_1 SCS72_0 SCS72_1 SCS73_0 SCS73_1 SIN8_0 SIN8_1 SOT8_0 (SDA8_0) MultiFunction Serial 8 SOT8_1 (SDA8_1) SCK8_0 (SCL8_0) SCK8_1 (SCL8_1) Multi-function serial interface ch 7 chip select 1 input/output pin Multi-function serial interface ch 7 chip select 2 input/output pin Multi-function serial interface ch 7 chip select 3 input/output pin Multi-function serial interface ch 8 input pin Multi-function serial interface ch 8 output pin. This pin operates as SOT8 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA8 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 8 clock I/O pin. This pin operates as SCK8 when it is used in a CSIO (operation mode 2) and as SCL8 when it is used in an I2C (operation mode 4). Document Number: 002-04988 Rev. *C LQQ 216 14 103 Pin Number LQP LQS 176 144 13 10 - LBE 192 E5 - 15 14 11 F1 102 - - - 16 15 12 F2 101 - - - 17 94 18 95 10 68 11 69 91 138 16 17 10 11 76 112 13 14 60 - F3 F4 E2 E3 K9 G13 92 77 61 P10 139 113 - F14 93 78 62 N10 140 114 - G12 Page 50 of 198 S6E2C3 Series Module MultiFunction Serial 9 Pin Name Function SIN9_0 SIN9_1 SOT9_0 (SDA9_0) Multi-function serial interface ch 9 input pin Multi-function serial interface ch 9 output pin. This pin operates as SOT9 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA9 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 9 clock I/O pin. This pin operates as SCK9 when it is used in a CSIO (operation mode 2) and as SCL9 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 10 input pin Multi-function serial interface ch 10 output pin. This pin operates as SOT10 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA10 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 10 clock I/O pin. This pin operates as SCK10 when it is used in a CSIO (operation mode 2) and as SCL10 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 11 input pin Multi-function serial interface ch 11 output pin. This pin operates as SOT11 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA11 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 11 clock I/O pin. This pin operates as SCK11 when it is used in a CSIO (operation mode 2) and as SCL11 when it is used in an I2C (operation mode 4). SOT9_1 (SDA9_1) SCK9_0 (SCL9_0) SCK9_1 (SCL9_1) SIN10_0 SIN10_1 SOT10_0 (SDA10_0) MultiFunction Serial 10 SOT10_1 (SDA10_1) SCK10_0 (SCL10_0) SCK10_1 (SCL10_1) SIN11_0 SIN11_1 SOT11_0 (SDA11_0) MultiFunction Serial 11 SOT11_1 (SDA11_1) SCK11_0 (SCL11_0) SCK11_1 (SCL11_1) Document Number: 002-04988 Rev. *C LQQ 216 82 120 Pin Number LQP LQS 176 144 67 57 - LBE 192 L8 - 83 68 58 K8 121 - - - 84 69 59 J8 122 - - - 114 51 94 41 78 - L11 L2 115 95 79 K13 52 42 - L3 116 96 80 K12 53 43 - M2 123 26 99 - 83 - J13 - 124 100 84 J12 27 - - - 125 101 85 J11 28 - - - Page 51 of 198 S6E2C3 Series Module MultiFunction Serial 12 Pin Name Function SIN12_0 SIN12_1 SOT12_0 (SDA12_0) Multi-function serial interface ch 12 input pin Multi-function serial interface ch 12 output pin. This pin operates as SOT12 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA12 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 12 clock I/O pin. This pin operates as SCK12 when it is used in a CSIO (operation mode 2) and as SCL12 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 13 input pin Multi-function serial interface ch 13 output pin. This pin operates as SOT13 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA13 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 13 clock I/O pin. This pin operates as SCK13 when it is used in a CSIO (operation mode 2) and as SCL13 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 14 input pin Multi-function serial interface ch 14 output pin. This pin operates as SOT14 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA14 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 14 clock I/O pin. This pin operates as SCK14 when it is used in a CSIO (operation mode 2) and as SCL14 when it is used in an I2C (operation mode 4). SOT12_1 (SDA12_1) SCK12_0 (SCL12_0) SCK12_1 (SCL12_1) SIN13_0 SIN13_1 SOT13_0 (SDA13_0) MultiFunction Serial 13 SOT13_1 (SDA13_1) SCK13_0 (SCL13_0) SCK13_1 (SCL13_1) SIN14_0 SIN14_1 SOT14_0 (SDA14_0) MultiFunction Serial 14 SOT14_1 (SDA14_1) SCK14_0 (SCL14_0) SCK14_1 (SCL14_1) Document Number: 002-04988 Rev. *C LQQ 216 133 65 Pin Number LQP LQS 176 144 109 89 - LBE 192 G14 - 134 110 90 H13 66 - - - 135 111 91 H11 67 - - - 48 206 38 - 33 - K3 - 49 39 34 K4 205 - - - 50 40 35 L1 204 - - - 30 201 21 - 18 - G3 - 31 22 19 G4 200 - - - 32 23 20 G5 199 - - - Page 52 of 198 S6E2C3 Series Module MultiFunction Serial 15 Pin Name Function SIN15_0 SIN15_1 SOT15_0 (SDA15_0) Multi-function serial interface ch 15 input pin Multi-function serial interface ch 15 output pin. This pin operates as SOT15 when it is used in a UART/CSIO/LIN (operation modes 0 to 3) and as SDA15 when it is used in an I2C (operation mode 4). Multi-function serial interface ch 15 clock I/O pin. This pin operates as SCK15 when it is used in a CSIO (operation mode 2) and as SCL15 when it is used in an I2C (operation mode 4). SOT15_1 (SDA15_1) SCK15_0 (SCL15_0) SCK15_1 (SCL15_1) Document Number: 002-04988 Rev. *C LQQ 216 59 19 Pin Number LQP LQS 176 144 49 41 - LBE 192 L4 - 60 50 42 M4 20 - - - 61 51 43 N4 21 - - - Page 53 of 198 S6E2C3 Series Module Pin Name LQQ 216 Pin Number LQP LQS 176 144 Input signal controlling waveform generator outputs RTO00 to RTO05 of Multi-Function Timer 0. 44 34 29 LBE 192 J3 21 - - - 16-bit free-run timer ch 0 external clock input pin 37 27 22 J1 29 - - - IC00_0 43 33 28 J4 IC00_1 22 - - - IC01_0 42 32 27 J5 26 - - - 41 31 26 H6 IC02_1 27 - - - IC03_0 38 28 23 H3 IC03_1 28 - - - Waveform generator output pin of MultiFunction Timer 0. This pin operates as PPG00 when it is used in PPG0 output modes. 45 35 30 J2 10 10 - E2 Waveform generator output pin of MultiFunction Timer 0. This pin operates as PPG00 when it is used in PPG0 output modes. 46 36 31 K1 11 11 - E3 Waveform generator output pin of MultiFunction Timer 0. This pin operates as PPG02 when it is used in PPG0 output modes. 47 37 32 K2 12 12 - E4 Waveform generator output pin of MultiFunction Timer 0. This pin operates as PPG02 when it is used in PPG0 output modes. 48 38 33 K3 13 - - - Waveform generator output pin of MultiFunction Timer 0. This pin operates as PPG04 when it is used in PPG0 output modes. 49 39 34 K4 19 - - - Waveform generator output pin of MultiFunction Timer 0. This pin operates as PPG04 when it is used in PPG0 output modes. 50 40 35 L1 20 - - - DTTI0X_0 DTTI0X_1 FRCK0_0 FRCK0_1 IC01_1 IC02_0 RTO00_0 (PPG00_0) MultiFunction Timer 0 Function RTO00_1 (PPG00_1) RTO01_0 (PPG00_0) RTO01_1 (PPG00_1) RTO02_0 (PPG02_0) RTO02_1 (PPG02_1) RTO03_0 (PPG02_0) RTO03_1 (PPG02_1) RTO04_0 (PPG04_0) RTO04_1 (PPG04_1) RTO05_0 (PPG04_0) RTO05_1 (PPG04_1) 16-bit input capture input pin of MultiFunction Timer 0. ICxx describes channel number. Document Number: 002-04988 Rev. *C Page 54 of 198 S6E2C3 Series Module Pin Name LQQ 216 Pin Number LQP LQS 176 144 Input signal controlling waveform generator outputs RTO10 to RTO15 of Multi-Function Timer 1. 70 55 47 LBE 192 L5 94 - - - 16-bit free-run timer ch 1 external clock input pin 71 56 48 M5 78 63 - K5 IC10_0 96 79 63 L10 IC10_1 95 - - - IC11_0 97 80 64 K10 101 - - - 98 81 65 M10 IC12_1 102 - - - IC13_0 99 82 66 N11 IC13_1 103 - - - Waveform generator output pin of MultiFunction Timer 1. This pin operates as PPG10 when it is used in PPG1 output modes. 56 46 38 N2 85 70 - N8 Waveform generator output pin of MultiFunction Timer 1. This pin operates as PPG10 when it is used in PPG1 output modes. 57 47 39 N3 86 71 - M8 Waveform generator output pin of MultiFunction Timer 1. This pin operates as PPG12 when it is used in PPG1 output modes. 58 48 40 M3 87 72 - N9 Waveform generator output pin of MultiFunction Timer 1. This pin operates as PPG12 when it is used in PPG1 output modes. 59 49 41 L4 88 73 - P9 Waveform generator output pin of MultiFunction Timer 1. This pin operates as PPG14 when it is used in PPG1 output modes. 60 50 42 M4 89 74 - M9 Waveform generator output pin of MultiFunction Timer 1. This pin operates as PPG14 when it is used in PPG1 output modes. 61 51 43 N4 90 75 - L9 DTTI1X_0 DTTI1X_1 FRCK1_0 FRCK1_1 IC11_1 IC12_0 RTO10_0 (PPG10_0) MultiFunction Timer 1 Function RTO10_1 (PPG10_1) RTO11_0 (PPG10_0) RTO11_1 (PPG10_1) RTO12_0 (PPG12_0) RTO12_1 (PPG12_1) RTO13_0 (PPG12_0) RTO13_1 (PPG12_1) RTO14_0 (PPG14_0) RTO14_1 (PPG14_1) RTO15_0 (PPG14_0) RTO15_1 (PPG14_1) 16-bit input capture input pin of MultiFunction Timer 1. ICxx describes channel number. Document Number: 002-04988 Rev. *C Page 55 of 198 S6E2C3 Series Module Pin Name LQQ 216 Pin Number LQP LQS 176 144 8 8 8 LBE 192 D3 202 - - - 17 16 13 F3 197 165 135 C6 IC20_0 9 9 9 D4 IC20_1 201 - - - IC21_0 14 13 10 E5 200 - - - 15 14 11 F1 IC22_1 199 - - - IC23_0 16 15 12 F2 IC23_1 198 166 136 D6 2 2 2 B2 203 - - - 3 3 3 C2 204 - - - 4 4 4 C3 205 - - - 5 5 5 D5 206 - - - 6 6 6 D2 207 167 - E6 7 7 7 D1 208 168 - B5 DTTI2X_0 DTTI2X_1 FRCK2_0 FRCK2_1 IC21_1 IC22_0 RTO20_0 (PPG20_0) MultiFunction Timer 2 Function RTO20_1 (PPG20_1) RTO21_0 (PPG20_0) RTO21_1 (PPG20_1) RTO22_0 (PPG22_0) RTO22_1 (PPG22_1) RTO23_0 (PPG22_0) RTO23_1 (PPG22_1) RTO24_0 (PPG24_0) RTO24_1 (PPG24_1) RTO25_0 (PPG24_0) RTO25_1 (PPG24_1) Input signal controlling waveform generator outputs RTO20 to RTO25 of Multi-Function Timer 1. 16-bit free-run timer ch 2 external clock input pin 16-bit input capture input pin of MultiFunction Timer 2. ICxx describes channel number. Waveform generator output pin of MultiFunction Timer 2. This pin operates as PPG20 when it is used in PPG2 output modes. Waveform generator output pin of MultiFunction Timer 2. This pin operates as PPG20 when it is used in PPG2 output modes. Waveform generator output pin of MultiFunction Timer 2. This pin operates as PPG22 when it is used in PPG2 output modes. Waveform generator output pin of MultiFunction Timer 2. This pin operates as PPG22 when it is used in PPG2 output modes. Waveform generator output pin of MultiFunction Timer 2. This pin operates as PPG24 when it is used in PPG2 output modes. Waveform generator output pin of MultiFunction Timer 2. This pin operates as PPG24 when it is used in PPG2 output modes. Document Number: 002-04988 Rev. *C Page 56 of 198 S6E2C3 Series Module Pin Name Function 56 46 38 65 - - - AIN0_2 114 94 78 L11 BIN0_0 57 47 39 N3 AIN0_1 BIN0_1 QPRC ch 0 AIN input pin QPRC ch 0 BIN input pin 66 - - - BIN0_2 115 95 79 K13 ZIN0_0 58 48 40 M3 67 - - - ZIN0_2 116 96 80 K12 AIN1_0 91 76 60 K9 94 - - - 123 99 83 J13 92 77 61 P10 45 - - - BIN1_2 124 100 84 J12 ZIN1_0 93 78 62 N10 101 - - - ZIN1_2 125 101 85 J11 AIN2_0 2 2 2 B2 32 23 20 G5 ZIN0_1 AIN1_1 QPRC ch 0 ZIN input pin QPRC ch 1 AIN input pin AIN1_2 Quadrature Position/ Revolution Counter 1 BIN1_0 BIN1_1 ZIN1_1 AIN2_1 Quadrature Position/ Revolution Counter 2 QPRC ch 1 BIN input pin QPRC ch 1 ZIN input pin QPRC ch 2 AIN input pin AIN2_2 120 - - - BIN2_0 3 3 3 C2 36 26 21 H2 BIN2_2 121 - - - ZIN2_0 4 4 4 C3 37 27 22 J1 ZIN2_2 122 - - - AIN3_0 18 17 14 F4 BIN2_1 ZIN2_1 AIN3_1 Quadrature Position/ Revolution Counter 3 Pin Number LQP LQS 176 144 LBE 192 N2 AIN0_0 Quadrature Position/ Revolution Counter 0 LQQ 216 QPRC ch 2 BIN input pin QPRC ch 2 ZIN input pin QPRC ch 3 AIN input pin 45 35 30 J2 AIN3_2 149 - - - BIN3_0 23 18 15 F5 46 36 31 K1 BIN3_2 150 - - - ZIN3_0 24 19 16 F6 47 37 32 K2 151 - - - BIN3_1 ZIN3_1 QPRC ch 3 BIN input pin QPRC ch 3 ZIN input pin ZIN3_2 Document Number: 002-04988 Rev. *C Page 57 of 198 S6E2C3 Series Module Pin Name RTCCO_0 Real-time clock RTCCO_1 SUBOUT_0 SUBOUT_1 USB0 139 33 - - - 211 171 139 C4 33 - - A3 142 UDP0 USB ch 0 device/host D + pin 215 175 143 A2 USB ch 0 external pull-up control pin 211 171 139 C4 UDM1 USB ch 1 device/host D – pin 160 130 106 D14 UDP1 USB ch 1 device/host D + pin 161 131 107 C14 155 125 101 E13 158 128 104 C13 14 13 10 E5 70 55 47 L5 212 172 140 B3 DA0 USB ch 1 external pull-up control pin Deep standby mode return signal input pin 0 Deep standby mode return signal input pin 1 Deep standby mode return signal input pin 2 Deep standby mode return signal input pin 3 D/A converter ch 0 analog output pin 100 83 67 M11 DA1 D/A converter ch 1 analog output pin 99 82 66 N11 On-board regulator control pin The return signal input pin from a hibernation state SD memory card interface SD memory card clock output pin SD memory card interface SD memory card command output 76 61 53 N6 77 62 54 M6 38 28 23 H3 41 31 26 H6 36 26 21 H2 37 27 22 J1 42 32 27 J5 43 33 28 J4 45 35 30 J2 44 34 29 J3 WKUP1 WKUP2 VREGCTL VWAKEUP S_CLK_0 S_CMD_0 S_DATA1_0 SD I/F 171 174 WKUP3 VBAT 211 LBE 192 C4 214 WKUP0 D/A converter Sub-clock output pin Pin Number LQP LQS 176 144 USB ch 0 device/host D – pin UHCONX1 Low power consumption mode 0.5 seconds pulse output pin of realtime clock LQQ 216 UDM0 UHCONX0 USB1 Function S_DATA0_0 S_DATA3_0 SD memory card interface SD memory card data bus S_DATA2_0 S_CD_0 S_WP_0 SD memory card interface SD memory card detection pin SD memory card interface SD memory card write protection Document Number: 002-04988 Rev. *C Page 58 of 198 S6E2C3 Series Module Pin Name Pin Number LQP LQS 176 144 I2S external clock pin 51 41 - I2SDO0_0 I2 S serial transition data output pin 52 42 - L3 I2SWS0_0 I2 S frame synchronization signal pin 53 43 - M2 I2SDI0_0 I2 S serial received data input pin 34 24 - G6 I2SCK0_0 I2 S bit clock pin 35 25 - H4 Q_SCK_0 SPI clock output pin 173 143 - D10 172 142 - C10 171 141 - B10 170 140 - D11 Q_IO3_0 169 139 - C11 Q_CS0_0 174 144 - B9 175 - - - 176 - - - Q_IO0_0 Q_IO1_0 High-speed quad SPI LQQ 216 LBE 192 L2 I2SMCLK0_0 I2 S Function Q_IO2_0 Q_CS1_0 SPI data input/output pin SPI chip select output pin Q_CS2_0 Document Number: 002-04988 Rev. *C Page 59 of 198 S6E2C3 Series Module Pin Name Reset INITX MD1 Mode MD0 VCC Function External reset Input pin A reset is valid when INITX = L. Mode 1 pin During serial programming to flash memory, MD1 = L must be input. Mode 0 pin During normal operation, MD0 = L must be input. During serial programming to flash memory, MD0 = H must be input. Power supply pin Power USBVCC0 USBVCC1 GND 3.3 V power supply port for USB I/O VSS Document Number: 002-04988 Rev. *C GND pin LQQ 216 Pin Number LQP LQS 176 144 LBE 192 72 57 49 N5 104 84 68 N13 105 85 69 N12 1 1 1 C1 39 29 24 H1 55 45 37 N1 64 54 46 P4 109 89 73 M14 137 - - - 163 133 109 A13 188 156 126 A9 213 173 141 A4 159 129 105 E14 40 30 25 H5 54 44 36 M1 63 53 45 P3 108 88 72 N14 136 - - - 162 132 108 B14 189 157 127 A8 216 176 144 B1 - - - E1 - - - G1 - - - P7 - - - P11 - - - L14 - - - A11 - - - A5 - - - N7 - - - M7 - - - K7 - - - J7 - - - G7 - - - H7 - - - H8 - - - G8 Page 60 of 198 S6E2C3 Series Module Clock Pin Name Main clock (oscillation) input pin 106 86 70 X1 Main clock (oscillation) I/O pin 107 87 71 P13 X0A Sub clock (oscillation) input pin 73 58 50 P5 X1A Sub clock (oscillation) I/O pin 74 59 51 P6 Built-in High-speed CR-oscillation clock output port A/D converter and D/A converter analog power-supply pin A/D converter analog reference voltage input pin A/D converter analog reference voltage input pin VBAT power supply pin Backup power supply (battery etc.) and system power supply A/D converter and D/A converter GND pin Power supply stabilization capacity pin 157 184 127 152 103 122 D13 E8 110 90 74 M13 112 92 76 L13 113 93 77 L12 75 60 52 P8 111 91 75 M12 62 52 44 P2 AVRL AVRH Analog GND C pin Pin Number LQP LQS 176 144 X0 AVCC VBAT Power LQQ 216 LBE 192 P12 CROUT_0 CROUT_1 Analog Power Function VBAT AVSS C Note: − While this device contains a Test Access Port (TAP) based on the IEEE 1149.1-2001 JTAG standard, it is not fully compliant to all requirements of that standard. This device may contain a 32-bit device ID that is the same as the 32-bit device ID in other devices with different functionality. The TAP pins may also be configurable for purposes other than access to the TAP controller. Document Number: 002-04988 Rev. *C Page 61 of 198 S6E2C3 Series 5. I/O Circuit Type Type A Circuit Remarks Pull-up resistor P-ch P-ch Digital output X1 N-ch Digital output R It is possible to select the main oscillation/GPIO function. Pull-up resistor control Digital input Standby mode control Clock input When the main oscillation is selected: ・ Oscillation feedback resistor: approximately 1 MΩ ・ Standby mode control Feedback resistor When the GPIO is selected: ・ CMOS level output. ・ CMOS level hysteresis input Standby mode control ・ Pull-up resistor control ・ Standby mode control Pull-up Digital input ・ Pull-up resistor: Standby mode control ・ IOH = -4 mA, IOL = 4 mA approximately 50 kΩ resistor R P-ch P-ch Digital output N-ch Digital output X0 Pull-up resistor control B ・ CMOS level hysteresis input Pull-up resistor ・ Pull-up resistor: Digital input Document Number: 002-04988 Rev. *C approximately 50 kΩ Page 62 of 198 S6E2C3 Series Type C Circuit Remarks Digital input ・ Open drain output Digital output N-ch ・ CMOS level hysteresis input E P-ch P-ch Digital output ・ CMOS level output ・ CMOS level hysteresis input ・ Pull-up resistor control ・ Standby mode control N-ch Digital output R ・ Pull-up resistor: approximately 50 kΩ ・ IOH = -4 mA, IOL = 4 mA ・ When this pin is used as an I2C Pull-up resistor control pin, the digital output P-ch transistor is always off. Digital input Standby mode control F P-ch P-ch Digital output ・ CMOS level output ・ CMOS level hysteresis input ・ Input control N-ch Digital output ・ Analog input ・ Pull-up resistor control ・ Standby mode control Pull-up resistor control R Digital input Standby mode control ・ Pull-up resistor: approximately 50 kΩ ・ IOH = -4 mA, IOL = 4 mA ・ When this pin is used as an I2C pin, the digital output P-ch transistor is always off. Analog input Input control Document Number: 002-04988 Rev. *C Page 63 of 198 S6E2C3 Series Type G Circuit P-ch Remarks Digital output P-ch ・ CMOS level output ・ CMOS level hysteresis input ・ Pull-up resistor control ・ Standby mode control ・ Pull-up resistor: N-ch Digital output R approximately 50 kΩ ・ IOH = -12 mA, IOL = 12 mA ・ When this pin is used as an I2C pin, the digital output P-ch Pull-up resistor control Digital input transistor is always off. Standby mode control H GPIO Digital output GPIO Digital input/output direction GPIO Digital input GPIO Digital input circuit control UDP output UDP/Pxx It is possible to select either USB I/O or GPIO function. USB Full-speed/Low-speed control UDP input When the USB I/O is selected: ・ Full-speed, low-speed control Differential UDM/Pxx Differential input USB/GPIO select When the GPIO is selected: ・ CMOS level output UDM input ・ CMOS level hysteresis input UDM output ・ Standby mode control ・ IOH = -20.5 mA, IOL = 18.5 mA USB Digital input/output direction GPIO Digital output GPIO Digital input/output direction GPIO Digital input GPIO Digital input circuit control Document Number: 002-04988 Rev. *C Page 64 of 198 S6E2C3 Series Type I Circuit P-ch Remarks P-ch Digital output ・ CMOS level output ・ CMOS level hysteresis input ・ 5V tolerant ・ Pull-up resistor control ・ Standby mode control ・ Pull-up resistor: approximately 50 kΩ N-ch Digital output ・ IOH = -4 mA, IOL = 4 mA ・ Available to control of PZR registers (pseudo-open drain R control) ・ Pull-up resistor control Digital input For PZR registers, refer to GPIO in the “FM4 Family Peripheral Manual Main Part (002-04856)”. Standby mode control J Mode input CMOS level hysteresis input K P-ch P-ch Digital output ・ CMOS level output ・ TTL level hysteresis input N-ch Digital output ・ Pull-up resistor control ・Standby mode control ・ Pull-up resistor: R approximately 50 kΩ ・ IOH = -4mA, IOL = 4mA Pull-up resistor control Digital input Standby mode control Document Number: 002-04988 Rev. *C Page 65 of 198 S6E2C3 Series Type Circuit Remarks L P-ch P-ch Digital output ・ CMOS level output ・ CMOS level hysteresis input ・ Pull-up resistor control ・ Standby mode control ・ Pull-up resistor: N-ch Digital output approximately 50 kΩ ・ IOH = -8 mA, IOL = 8 mA ・ When this pin is used as an I2C pin, the digital output P-ch Pull-up resistor control R transistor is always off. Digital input Standby mode control N ・ CMOS level output ・ CMOS level hysteresis input Pull-up resistor control P-ch P-ch Digital output ・ 5V tolerant ・ Pull-up resistor control ・ Standby mode control ・ Pull-up resistor: approximately 50 kΩ ・ IOH = -4 mA, IOL = 4 mA (GPIO) ・ IOL = 20mA (Fast mode Plus) N-ch N-ch Digital output ・ Available to control of PZR register (pseudo-open drain control) ・ For PZR registers, refer to GPIO R Fast mode control in the “FM4 Family Peripheral Manual Main Part (002-04856)”. ・ When this pin is used as an I2C Digital input Standby mode control Document Number: 002-04988 Rev. *C pin, the digital output P-ch transistor is always off. Page 66 of 198 S6E2C3 Series Type Circuit Remarks O ・ CMOS level output ・ CMOS level hysteresis input ・ 5V tolerant Pull-up resistor control P-ch P-ch Digital output ・ Pull-up resistor control ・ Pull-up resistor: approximately 50 kΩ ・ IOH = -4 mA, IOL = 4 mA ・ Available to control of PZR register (pseudo-open drain control) N-ch Digital output ・ For PZR registers, refer to GPIO in the “FM4 Family Peripheral Manual Main Part (002-04856)”. ・ For I/O setting, refer to VBAT Domain in the "FM4 Family Peripheral Manual Main Part R Digital input (002-04856).” P P-ch P-ch X0A Pull-up resistor control Digital output ・ CMOS level output ・ CMOS level hysteresis input ・ Pull-up resistor control ・ Pull-up resistor: N-ch Digital output approximately 50 kΩ ・ IOH = -4 mA, IOL = 4 mA ・ For I/O setting, refer to VBAT Domain in the "FM4 Family Peripheral Manual Main Part (002-04856).” R Digital input Standby mode control OSC Document Number: 002-04988 Rev. *C Page 67 of 198 S6E2C3 Series Type Q Circuit Pull-up resistor control Digital output P-ch X1A Remarks P-ch It is possible to select the sub oscillation/GPIO function. When the sub oscillation is selected: ・ Oscillation feedback resistor: Digital output N-ch approximately 10 MΩ When the GPIO is selected: ・ CMOS level output. ・ CMOS level hysteresis input ・ Pull-up resistor control R Digital input ・ Pull-up resistor: Standby mode control OSC ・ IOH = -4 mA, IOL = 4 mA RX approximately 50 kΩ ・ For I/O setting, refer to VBAT Domain in the "FM4 Family Peripheral Manual Main Part Standby mode control (002-04856).” Clock input R P-ch P-ch Pull-up resistor control Digital output ・ CMOS level output ・ CMOS level hysteresis input ・ Analog output ・ Pull-up resistor control N-ch Digital output ・ Standby mode control ・ Pull-up resistor: approximately 50 kΩ ・ IOH = -4 mA, IOL = 4 mA (4.5 V to 5.5 V) ・ IOH = -2 mA, IOL = 2 mA R Digital input (2.7 V to 4.5 V) Standby mode control Analog output Document Number: 002-04988 Rev. *C Page 68 of 198 S6E2C3 Series Type S Circuit Remarks ・ CMOS level output ・ (It is possible to select by port P-ch Pull-up resistor control drive capability. Select register [PDSR]) ・ CMOS level hysteresis input P-ch ・ Pull-up resistor control ・ Standby mode control Digital output ・ Pull-up resistor: approximately 50 kΩ ・ IOH = -10 mA, IOL = 10 mA (PDSR N-ch Port Drive Select = 1) ・ IOH = -4 mA, IOL = 4 mA (PDSR = 0) ・ When this pin is used as an I2C R Digital input pin, the digital output P-ch transistor is always off. Standby mode Control Document Number: 002-04988 Rev. *C Page 69 of 198 S6E2C3 Series 6. Handling Precautions Every semiconductor device has a characteristic, inherent rate of failure. The possibility of failure is greatly affected by the conditions in which they are used (circuit conditions, environmental conditions, etc.). This page describes precautions that must be observed to minimize the chance of failure and to obtain higher reliability from your Cypress semiconductor devices. 6.1 Precautions for Product Design This section describes precautions when designing electronic equipment using semiconductor devices. Absolute Maximum Ratings Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of certain established limits, called absolute maximum ratings. Do not exceed these ratings. Recommended Operating Conditions Recommended operating conditions are normal operating ranges for the semiconductor device. All the device's electrical characteristics are warranted when operated within these ranges. Always use semiconductor devices within the recommended operating conditions. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their sales representative beforehand. Processing and Protection of Pins These precautions must be followed when handling the pins that connect semiconductor devices to power supply and I/O functions. 1. Preventing Over-Voltage and Over-Current Conditions Exposure to voltage or current levels in excess of maximum ratings at any pin is likely to cause deterioration within the device, and in extreme cases leads to permanent damage of the device. Try to prevent such overvoltage or over-current conditions at the design stage. 2. Protection of Output Pins Shorting of output pins to supply pins or other output pins, or connection to large capacitance can cause large current flows. Such conditions, if present for extended periods of time, can damage the device; therefore, avoid this type of connection. 3. Handling of Unused Input Pins Unconnected input pins with very high impedance levels can adversely affect stability of operation. Such pins should be connected through an appropriate resistance to a power-supply pin or ground pin. Document Number: 002-04988 Rev. *C Page 70 of 198 S6E2C3 Series Latch-Up Semiconductor devices are constructed by the formation of p-type and n-type areas on a substrate. When subjected to abnormally high voltages, internal parasitic pnpn junctions (called thyristor structures) may be formed, causing large current levels in excess of several hundred milliamps to flow continuously at the power supply pin. This condition is called latch-up. CAUTION: The occurrence of latch-up not only causes loss of reliability in the semiconductor device, but can cause injury or damage from high heat, smoke or flame. To prevent this from happening, do the following: 1. Be sure that voltages applied to pins do not exceed the absolute maximum ratings. This should include attention to abnormal noise, surge levels, etc. 2. Be sure that abnormal current flows do not occur during the power-on sequence. Observance of Safety Regulations and Standards Most countries in the world have established standards and regulations regarding safety, protection from electromagnetic interference, etc. Customers are requested to observe applicable regulations and standards in the design of products. Fail-Safe Design As previously mentioned, all semiconductor devices have inherent rates of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. Precautions Related to Usage of Devices Cypress semiconductor devices are intended for use in standard applications (computers, office automation and other office equipment, industrial, communications, and measurement equipment, personal or household devices, etc.). CAUTION: Customers considering the use of our products in special applications where failure or abnormal operation may directly affect human lives or cause physical injury or property damage, or where extremely high levels of reliability are demanded (such as aerospace systems, atomic energy controls, sea floor repeaters, vehicle operating controls, medical devices for life support, etc.) are requested to consult with sales representatives before such use. The company will not be responsible for damages arising from such use without prior approval. 6.2 Precautions for Package Mounting Package mounting may be either lead insertion type or surface mount type. In either case, for heat resistance during soldering, you should only mount under Cypress's recommended conditions. For detailed information about mount conditions, contact your sales representative. Lead Insertion Type Mounting of lead insertion type packages onto printed circuit boards may be done by two methods: direct soldering on the board, or mounting by using a socket. Direct mounting onto boards normally involves processes for inserting leads into through-holes on the board and using the flow soldering (wave soldering) method of applying liquid solder. In this case, the soldering process usually causes leads to be subjected to thermal stress in excess of the absolute ratings for storage temperature. Mounting processes should conform to Cypress recommended mounting conditions. If socket mounting is used, differences in surface treatment of the socket contacts and IC lead surfaces can lead to contact deterioration after long periods. For this reason it is recommended that the surface treatment of socket contacts and IC leads be verified before mounting. Document Number: 002-04988 Rev. *C Page 71 of 198 S6E2C3 Series Surface Mount Type Surface mount packaging has longer and thinner leads than lead-insertion packaging, and therefore leads are more easily deformed or bent. The use of packages with higher pin counts and narrower pin pitch results in increased susceptibility to open connections caused by deformed pins, or shorting due to solder bridges. You must use appropriate mounting techniques. Cypress recommends the solder reflow method, and has established a ranking of mounting conditions for each product. Users are advised to mount packages in accordance with Cypress ranking of recommended conditions. Lead-Free Packaging CAUTION: When ball grid array (BGA) packages with Sn-Ag-Cu balls are mounted using Sn-Pb eutectic soldering, junction strength may be reduced under some conditions of use. Storage of Semiconductor Devices Because plastic chip packages are formed from plastic resins, exposure to natural environmental conditions will cause absorption of moisture. During mounting, the application of heat to a package that has absorbed moisture can cause surfaces to peel, reducing moisture resistance and causing packages to crack. To prevent this, do the following: 1. Avoid exposure to rapid temperature changes, which can cause moisture to condense inside the product. Store products in locations where temperature changes are slight. 2. Use dry boxes for product storage. Products should be stored below 70% relative humidity, and at temperatures between 5°C and 30°C. 3. When Dry Packages are opened, it is recommended to have humidity between 40% and 70%. 4. When necessary, Cypress packages semiconductor devices in highly moisture-resistant aluminum laminate bags, with a silica gel desiccant. Devices should be sealed in these aluminum laminate bags for storage. 5. Avoid storing packages where they are exposed to corrosive gases or high levels of dust. Baking Packages that have absorbed moisture may be de-moisturized by baking (heat drying). Follow the Cypress recommended conditions for baking. Condition: 125 °C/24 h Static Electricity Because semiconductor devices are particularly susceptible to damage by static electricity, you must take the following precautions: 1. Maintain relative humidity in the working environment between 40% and 70%. Use of an apparatus for ion generation may be needed to remove electricity. 2. Electrically ground all conveyors, solder vessels, soldering irons, and peripheral equipment. 3. Eliminate static body electricity by the use of rings or bracelets connected to ground through high resistance (on the level of 1 MΩ). Wearing of conductive clothing and shoes, and the use of conductive floor mats and other measures to minimize shock loads is recommended. 4. Ground all fixtures and instruments, or protect with anti-static measures. 5. Avoid the use of Styrofoam or other highly static-prone materials for storage of completed board assemblies. Document Number: 002-04988 Rev. *C Page 72 of 198 S6E2C3 Series 6.3 Precautions for Use Environment Reliability of semiconductor devices depends on ambient temperature and other conditions as described above. For reliable performance, do the following: 1. Humidity Prolonged use in high humidity can lead to leakage in devices as well as printed circuit boards. If high humidity levels are anticipated, consider anti-humidity processing. 2. Discharge of static electricity When high-voltage charges exist close to semiconductor devices, discharges can cause abnormal operation. In such cases, use anti-static measures or processing to prevent discharges. 3. Corrosive gases, dust, or oil Exposure to corrosive gases or contact with dust or oil may lead to chemical reactions that will adversely affect the device. If you use devices in such conditions, consider ways to prevent such exposure or to protect the devices. 4. Radiation, including cosmic radiation Most devices are not designed for environments involving exposure to radiation or cosmic radiation. Users should provide shielding as appropriate. 5. Smoke, flame CAUTION: Plastic molded devices are flammable and therefore should not be used near combustible substances. If devices begin to smoke or burn, there is danger of the release of toxic gases. Customers considering the use of Cypress products in other special environmental conditions should consult with sales representatives. Document Number: 002-04988 Rev. *C Page 73 of 198 S6E2C3 Series 7. Handling Devices Power-Supply Pins In products with multiple VCC and VSS pins, respective pins at the same potential are interconnected within the device in order to prevent malfunctions such as latch-up. All of these pins should be connected externally to the power supply or ground lines, however, in order to reduce electromagnetic emission levels, to prevent abnormal operation of strobe signals caused by the rise in the ground level, and to conform to the total output current rating. Be sure to connect the current-supply source with the power pins and GND pins of this device at low impedance. It is also advisable that a ceramic capacitor of approximately 0.1 µF be connected as a bypass capacitor between VCC and VSS near this device. A malfunction may occur when the power-supply voltage fluctuates rapidly even though the fluctuation is within the guaranteed operating range of the VCC power supply voltage. As a rule of voltage stabilization, suppress voltage fluctuation so that the fluctuation in VCC ripple (peak-to-peak value) at the commercial frequency (50 Hz/60 Hz) does not exceed 10% of the standard VCC value, and the transient fluctuation rate does not exceed 0.1 V/μs at a momentary fluctuation such as switching the power supply. Crystal Oscillator Circuit Noise near the X0/X1 and X0A/X1A pins may cause the device to malfunction. Design the printed circuit board so that X0/X1, X0A/X1A pins, the crystal oscillator (or ceramic oscillator), and the bypass capacitor to ground are located as close to the device as possible. It is strongly recommended that the PC board artwork be designed such that the X0/X1 and X0A/X1A pins are surrounded by ground plane, as this is expected to produce stable operation. Evaluate the oscillation introduced by the use of the crystal oscillator by your mount board. Sub Crystal Oscillator The sub-oscillator circuit for devices in this family is low gain to keep current consumption low. To stabilize the oscillation, Cypress recommends a crystal oscillator that meets the following conditions:  Surface mount type Size: Load capacitance:  Lead type Load capacitance: More than 3.2 mm × 1.5 mm approximately 6 pF to 7 pF approximately 6 pF to 7 pF Document Number: 002-04988 Rev. *C Page 74 of 198 S6E2C3 Series Using an External Clock When using an external clock as an input of the main clock, set X0/X1 to the external clock input, and input the clock to X0. X1(PE3) can be used as a general-purpose I/O port. Similarly, when using an external clock as an input of the sub clock, set X0A/X1A to the external clock input and input the clock to X0A. X1A (P47) can be used as a general-purpose I/O port.  Example of Using an External Clock Device X0(X0A) Set as external clock input Can be used as general-purpose I/O ports. X1(PE3), X1A (P47) Handling When Using Multi-Function Serial Pin as I2C Pin If the application uses the multi-function serial pin as an I2C pin, the P-channel transistor of the digital output must be disabled. I2C pins need to conform to electrical limitations like other pins, however, and avoid connecting to live external systems with the MCU power off. C Pin Devices in this series contain a regulator. Be sure to connect a smoothing capacitor (CS) for the regulator between the C pin and the GND pin. Please use a ceramic capacitor or a capacitor of equivalent frequency characteristics as a smoothing capacitor. Some laminated ceramic capacitors have a large capacitance variation due to thermal fluctuation. Please select a capacitor that meets the specifications in the operating conditions to use by evaluating the temperature characteristics of the device. A smoothing capacitor of about 4.7 μF would be recommended for this series. C Device CS VSS GND Mode Pins (MD0) Connect the MD pin (MD0) directly to VCC or VSS pins. Design the printed circuit board such that the pull-up/down resistance stays low, the distance between the mode pins and VCC pins or VSS pins is as short as possible, and the connection impedance is low when the pins are pulled up/down such as for switching the pin level and rewriting the flash memory data. This is important to prevent the device from erroneously switching to test mode as a result of noise. Document Number: 002-04988 Rev. *C Page 75 of 198 S6E2C3 Series Notes on Power-on Turn power on/off in the following order or at the same time. The device operates normally after all power on. VBAT only Power-on is possible when VBAT and VCC turns Power-on and Hibernation control is setting and then VCC turns Power-off. About Hibernation control, see Chapter 7-2: VBAT Domain(B) in FM4 Family Peripheral Manual Main Part(002-04856). Turning on: Turning off: VBAT → VCC → USBVCC0 VBAT → VCC → USBVCC1 VCC → AVCC → AVRH AVRH → AVCC → VCC USBVCC1 → VCC → VBAT USBVCC0 → VCC → VBAT Serial Communication There is a possibility of receiving incorrect data as a result of noise or other issues introduced by the serial communication. Take care to design the printed circuit board to minimize noise. Consider the case of introducing error as a result of noise, perform error detection such as by applying a checksum of data at the end. If an error is detected, retransmit the data. Differences in Characteristics within the Product Line The electric characteristics including power consumption, ESD, latch-up, noise, and oscillation differ among members of the product line because chip layout and memory structures are not the same; for example, different sizes, flash versus ROM, etc. If you are switching to a different product of the same series, please make sure to evaluate the electric characteristics. Pull-Up Function of 5 V Tolerant I/O Please do not input the signal more than VCC voltage at the time of Pull-Up function use of 5 V tolerant I/O. Pin Doubled as Debug Function The pin doubled as TDO/TMS/TDI/TCK/TRSTX, SWO/SWDIO/SWCLK should be used as output only. Do not use as input. Document Number: 002-04988 Rev. *C Page 76 of 198 S6E2C3 Series 8. Block Diagram S6E2C3AH/J/L, S6E2C39H/J/L, S6E2C38H/J/L TRSTX,TCK, TDI,TMS TDO SWJ-DP ETM/HTM* TRACEDx, TRACECLK TPIU/ETB* ROM Table SRAM0 96/144/192 Kbytes SRAM1 32 Kbytes Cortex-M4　Core I @200 MHz(Max) D FPU SRAM2 32 Kbytes MPU NVIC Multi-layer AHB (Max 200 MHz) Sys AHB-APB Bridge: APB0(Max 100 MHz) Dual-Timer Watchdog Timer (Software) Clock Reset Generator INITX Watchdog Timer (Hardware) CSV MainFlash I/F MainFlash/DualFlash 2 Mbytes(1M+1M)/ 1.5 Mbytes(1M+0.5M)/ 1 Mbytes(MainOnly) Trace Buffer (16 Kbytes) Security DualFlash I/F USB2.0 (Host/ Func) PHY USB2.0 (Host/ Func) PHY USBVCC0 UDP0,UDM0 UHCONX0 USBVCC1 UDP1,UDM1 UHCONX1 DMAC 8ch. CLK DSTC PRG-CRC Accelerator Source Clock X0A X1A Main Osc CR 100 kHz CR 4 MHz PLL VBAT Domain Sub Osc I2S 1unit AHB-AHB Bridge (Slave) X0 X1 GPIO MODE-Ctrl Unit 2 TIOBx AINx BINx ZINx 16-bit Input Capture 4ch. 16-bit Free-run Timer 3ch. 16-bit Output Compare 6ch. DTTI0X Waveform Generator 3ch. 16-bit PPG 3ch. Multi-function Timer × 3 VBAT VWAKEUP VREGCTL RTCCO, SUBOUT DAx Document Number: 002-04988 Rev. *C S_DATAx S_CD,S_WP Q_IOx QPRC 4ch. IC0x S_CLK,S_CMD SD-CARD I/F Hi-Speed Quad SPI A/D Activation Compare 6ch. RTO0x . . . PFx MD0, MD1 Q_SCK, Q_CSx Base Timer 16-bit 32ch./ 32-bit 16ch. TIOAx VBAT Domain Real-Time Clock Port Ctrl. 12-bit D/A Converter 2units MADx External Bus I/F MADATAx MCSXx,MDQMx, MOEX,MWEX, MALE,MRDY, MNALE,MNCLE, MNWEX,MNREX, MCLKOUT,MSDWEX, MSDCLK,MSDCKE, MRASX,MCASX AHB-APB Bridge : APB2 (Max 100 MHz) Unit 1 AHB-APB Bridge : APB1 (Max 200 MHz) ANxx AHB-AHB Bridge (Master) 12-bit A/D Converter Unit 0 ADTGx FRCK0 P0x, P1x, PIN-Function-Ctrl CROUT AVCC, AVSS, AVRH, AVRL I2SMCLK, I2SWS, I2SCK I2SDI I2SDO USB Clock Ctrl PLL I2S Clock Ctrl PLL Power-On Reset LVD Ctrl LVD IRQ-Monitor Regulator C CRC Accelerator Watch Counter Deep Standby Ctrl WKUPx Peripheral Clock Gating Low-speed CR Prescaler External Interrupt Controller 32-pin + NMI INTx NMIX Multi-function Serial I/F 16ch. (with FIFO ch.0 to ch.7) HW flow control(ch.4,5) SCKx SINx SOTx CTSx RTSx Page 77 of 198 S6E2C3 Series 9. Memory Size See Memory size in 1. Product Lineup to confirm the memory size. 10. Memory Map Memory Map (1) Peripherals Area 0x41FF_FFFF Reserved 0x4008_1000 0x4008_0000 0x4007_0000 0x4006_F000 0x4006_E000 0xFFFF_FFFF 0x4006_D000 Reserved 0x4006_C000 Programmable-CRC Reserved GPIO SD-Card I/F Reserved I2S 0xE010_0000 0xE000_0000 0xD000_0000 Cortex-M4 Private Peripherals Reg. Area External Device Area Reserved 0x4006_2000 0x4006_1000 0x4006_0000 0x6000_0000 0x4005_0000 0x4004_0000 Reserved 0x4400_0000 0x4200_0000 0x4003_F000 0x4003_E000 32 Mbytes Bit band alias 0x4003_D000 0x4003_C800 DSTC DMAC USB ch.1 USB ch.0 EXT-bus I/F Reserved I2S prescaler Reserved Peripheral Clock Gating 0x4003_C000 Low Speed CR Prescaler 0x4003_C100 Peripherals 0x4000_0000 0x4003_B000 0x4003_A000 Reserved 0x2400_0000 0x2200_0000 0x4003_9000 0x4003_8000 32 Mbytes Bit band alias DualFlash 0x200F_0000 0x4003_7000 0x4003_6000 0x4003_5000 0x4003_4000 0x4003_3000 0x4003_2000 Reserved See "Memory詳細は Map メモリサイズの 次項の「●メモリマップ(2)」 (2) and (3)" for を参照してください。 memory size details. 0x2004_8000 0x2004_0000 0x2003_8000 0x2000_0000 0x1FFF_0000 0x0050_0000 0x0040_0000 0x4003_0000 0x4002_F000 SRAM2 SRAM1 Reserved SRAM0 Reserved Security/CR Trim MainFlash 0x0000_0000 0x4003_1000 0x4002_E000 Reserved 0x4002_8000 0x4002_7000 0x4002_6000 0x4002_5000 0x4002_4000 0x4002_3000 0x4002_2000 0x4002_1000 0x4002_0000 0x4001_6000 0x4001_5000 0x4001_3000 0x4001_2000 0x4001_1000 0x4001_0000 0x4000_1000 0x4000_0000 Document Number: 002-04988 Rev. *C RTC/Port Ctrl Watch Counter CRC MFS Reserved USB Clock ctrl LVD/DS mode Reserved D/AC Reserved Int-Req.Read EXTI Reserved CR Trim A/DC QPRC Base Timer PPG Reserved MFT Unit2 MFT Unit1 MFT Unit0 Reserved Dual Timer Reserved SW WDT HW WDT Clock/Reset Reserved MainFlash I/F Page 78 of 198 S6E2C3 Series Memory Map (2) S6E2C3AH/J/L S6E2C39H/J/L 0x2020_0000 0x2020_0000 Reserved 0x2003_8000 0x2020_0000 Reserved 0x2004_8000 0x2004_0000 S6E2C38H/J/L Reserved 0x2004_8000 SRAM2 32 Kbytes SRAM1 32 Kbytes 0x2004_0000 0x2003_8000 Reserved 0x2004_8000 SRAM2 32 Kbytes SRAM1 32 Kbytes 0x2004_0000 0x2003_8000 Reserved 0x2000_0000 Reserved 0x2000_0000 0x2000_0000 SRAM0 128 Kbytes SRAM0 192 Kbytes SRAM2 32 Kbytes SRAM1 32 Kbytes 0x1FFF_0000 SRAM0 64 Kbytes 0x1FFE_0000 0x1FFD_0000 0x0041_0000 0x0040_2000 0x0040_0000 SA3(#0) (8KB) General purpose CR trimming Security 0x0040_8000 0x0040_6000 0x0040_4000 0x0040_2000 0x0040_0000 SA0-3(#1) (8KBx4) SA3(#0) (8KB) General purpose CR trimming Security 0x0040_8000 0x0040_6000 0x0040_4000 0x0040_2000 0x0040_0000 SA0-3(#1) (8KBx4) SA3(#0) (8KB) General purpose CR trimming Security MainFlash 40 Kbytes 0x0040_4000 SA0-3(#1) (8KBx4) 0x0041_0000 MainFlash 40 Kbytes 0x0040_6000 0x0041_0000 MainFlash 40 Kbytes 0x0040_8000 Reserved Reserved Reserved Reserved Reserved 0x0020_0000 Reserved SA9-23(#1) (64KBx15) SA9-15(#1) (64KBx7) SA8(#1) (32KB) SA4-7(#1) (8KBx4) 0x0010_0000 0x0000_0000 SA8(#0) (32KB) SA4-7(#0) (8KBx4) SA9-23(#0) (64KBx15) 0x0000_0000 SA8(#0) (32KB) SA4-7(#0) (8KBx4) 0x0010_0000 SA9-23(#0) (64KBx15) 0x0000_0000 SA8(#0) (32KB) SA4-7(#0) (8KBx4) MainFlash 1 Mbytes SA9-23(#0) (64KBx15) MainFlash 1.5 Mbytes MainFlash 2 Mbytes 0x0010_0000 SA8(#1) (32KB) SA4-7(#1) (8KBx4) 0x0018_0000 *: See S6E2CC/S6E2C5/S6E2C4/S6E2C3/S6E2C2/S6E2C1 Series Flash Programming Manual to confirm the detail of flash Memory. Document Number: 002-04988 Rev. *C Page 79 of 198 S6E2C3 Series Memory Map (2) During Dual Flash Mode S6E2C3AH/J/L 0x200F_8000 SA8(#1) (32KB) SA4-7(#1) (8KBx4) SA0-3(#1) (8KBx4) 0x2018_0000 0x2010_0000 0x200F_8000 Reserved 0x2003_8000 SA9-15(#1) (64KBx7) SA8(#1) (32KB) SA4-7(#1) (8KBx4) SA0-3(#1) (8KBx4) 0x2020_0000 Reserved 0x2010_0000 0x200F_8000 Reserved 0x2004_8000 0x2004_0000 Reserved 0x2004_0000 0x2003_8000 Reserved 0x2004_8000 SRAM2 32 Kbytes SRAM1 32 Kbytes 0x2004_0000 0x2003_8000 Reserved 0x2000_0000 SRAM2 32 Kbytes SRAM1 32 Kbytes Reserved 0x2000_0000 0x2000_0000 SRAM0 128 Kbytes SRAM0 192 Kbytes SA0-3(#1) (8KBx4) Reserved 0x2004_8000 SRAM2 32 Kbytes SRAM1 32 Kbytes DualFlash 32 Kbytes 0x2010_0000 0x2020_0000 S6E2C38H/J/L DualFlash 512 Kbytes +32 Kbytes SA9-23(#1) (64KBx15) DualFlash 1 Mbytes +32 Kbytes 0x2020_0000 S6E2C39H/J/L 0x1FFF_0000 SRAM0 64 Kbytes 0x1FFE_0000 0x1FFD_0000 0x0041_0000 0x0040_2000 0x0040_0000 SA3(#0) (8KB) General purpose CR trimming / HTM Security 0x0040_8000 0x0040_6000 0x0040_4000 0x0040_2000 0x0040_0000 Reserved SA3(#0) (8KB) General purpose CR trimming / HTM Security 0x0040_4000 0x0040_0000 SA3(#0) (8KB) General purpose CR trimming / HTM Security 0x0010_0000 SA8(#0) (32KB) SA4-7(#0) (8KBx4) SA9-23(#0) (64KBx15) 0x0000_0000 SA8(#0) (32KB) SA4-7(#0) (8KBx4) MainFlash 1 Mbytes SA9-23(#0) (64KBx15) 0x0000_0000 Reserved Reserved MainFlash 1 Mbytes Document Number: 002-04988 Rev. *C MainFlash 1 Mbytes SA8(#0) (32KB) SA4-7(#0) (8KBx4) 0x0040_6000 0x0040_2000 0x0010_0000 SA9-23(#0) (64KBx15) 0x0040_8000 Reserved 0x0010_0000 0x0000_0000 Reserved MainFlash 8 Kbytes 0x0040_4000 Reserved 0x0041_0000 MainFlash 8 Kbytes 0x0040_6000 0x0041_0000 MainFlash 8 Kbytes 0x0040_8000 Reserved Reserved Reserved Page 80 of 198 S6E2C3 Series Memory Map (3) S6E2C3AH 0xD000_0000 S6E2C3AJ 0xD000_0000 S6E2C3AL 0xD000_0000 Hi-Speed Quad SPI 256 Mbytes 0xC000_0000 0xC000_0000 Reserved 0x8000_0000 Hi-Speed Quad SPI 256 Mbytes 0xC000_0000 Reserved 0x8000_0000 Reserved 0x8000_0000 SDRAM 256 Mbytes 0x7000_0000 0x7000_0000 SRAM /NOR Flash Memory /NAND Flash Memory 256 Mbytes 0x6000_0000 Document Number: 002-04988 Rev. *C SDRAM 256 Mbytes 0x7000_0000 SRAM /NOR Flash Memory /NAND Flash Memory 256 Mbytes 0x6000_0000 SRAM /NOR Flash Memory /NAND Flash Memory 256 Mbytes 0x6000_0000 Page 81 of 198 S6E2C3 Series Peripheral Address Map Start Address 0x4000_0000 0x4000_1000 0x4001_0000 0x4001_1000 0x4001_2000 0x4001_3000 0x4001_5000 0x4001_6000 0x4002_0000 0x4002_1000 0x4002_2000 0x4002_3000 0x4002_4000 0x4002_5000 0x4002_6000 0x4002_7000 0x4002_8000 0x4002_E000 0x4002_F000 0x4003_0000 0x4003_1000 0x4003_2000 0x4003_3000 0x4003_4000 0x4003_5000 0x4003_5800 0x4003_6000 0x4003_7000 0x4003_8000 0x4003_9000 0x4003_A000 0x4003_B000 0x4003_C000 0x4003_C100 0x4003_C800 0x4003_D000 0x4003_E000 0x4003_F000 0x4004_0000 0x4005_0000 0x4006_0000 0x4006_1000 0x4006_2000 0x4006_C000 0x4006_D000 0x4006_E000 0x4006_F000 0x4007_0000 0x4008_0000 0x4008_1000 0x200E_0000 0xD000_0000 End Address 0x4000_0FFF 0x4000_FFFF 0x4001_0FFF 0x4001_1FFF 0x4001_2FFF 0x4001_4FFF 0x4001_5FFF 0x4001_FFFF 0x4002_0FFF 0x4002_1FFF 0x4002_2FFF 0x4002_3FFF 0x4002_4FFF 0x4002_5FFF 0x4002_6FFF 0x4002_7FFF 0x4002_DFFF 0x4002_EFFF 0x4002_FFFF 0x4003_0FFF 0x4003_1FFF 0x4003_2FFF 0x4003_3FFF 0x4003_4FFF 0x4003_57FF 0x4003_5FFF 0x4003_6FFF 0x4003_7FFF 0x4003_8FFF 0x4003_9FFF 0x4003_AFFF 0x4003_BFFF 0x4003_C0FF 0x4003_C7FF 0x4003_CFFF 0x4003_DFFF 0x4003_EFFF 0x4003_FFFF 0x4004_FFFF 0x4005_FFFF 0x4006_0FFF 0x4006_1FFF 0x4006_BFFF 0x4006_CFFF 0x4006_DFFF 0x4006_EFFF 0x4006_FFFF 0x4007_FFFF 0x4008_0FFF 0x41FF_FFFF 0x200E_FFFF 0xDFFF_FFFF Document Number: 002-04988 Rev. *C Bus AHB APB0 APB1 APB2 AHB Peripherals MainFlash I/F register Reserved Clock/reset control Hardware watchdog timer Software watchdog timer Reserved Dual-timer Reserved Multi-Function Timer unit 0 Multi-Function Timer unit 1 Multi-Function Timer unit 2 Reserved PPG Base timer Quadrature position/revolution counter A/D converter Reserved Internal CR trimming Reserved External interrupt controller Interrupt request batch-read function Reserved D/A converter Reserved Low voltage detector Deep standby mode Controller USB clock generator Reserved Multi-function serial interface CRC Watch counter RTC/port control Low-speed CR prescaler Peripheral clock gating Reserved I2S prescaler Reserved External memory interface USB ch 0 USB ch 1 DMAC register DSTC register Reserved I2 S Reserved SD card I/F GPIO Reserved Programmable-CRC Reserved Workflash I/F register High-speed quad SPI control register Page 82 of 198 S6E2C3 Series 11. Pin Status in Each CPU State The terms used for pin status have the following meanings:  INITX = 0 This is the period when the INITX pin is at the L level.  INITX = 1 This is the period when the INITX pin is at the H level.  SPL = 0 This is the status that the standby pin level setting bit (SPL) in the standby mode control register (STB_CTL) is set to 0.  SPL = 1 This is the status that the standby pin level setting bit (SPL) in the standby mode control register (STB_CTL) is set to 1.  Input enabled Indicates that the input function can be used.  Internal input fixed at 0 This is the status that the input function cannot be used. Internal input is fixed at L.  Hi-Z Indicates that the pin drive transistor is disabled and the pin is put in the Hi-Z state.  Setting disabled Indicates that the setting is disabled.  Maintain previous state Maintains the state that was immediately prior to entering the current mode. If a built-in peripheral function is operating, the output follows the peripheral function. If the pin is being used as a port, that output is maintained.  Analog input is enabled Indicates that the analog input is enabled.  Trace output Indicates that the trace function can be used.  GPIO selected In Deep standby mode, pins switch to the general-purpose I/O port.  Setting prohibition Prohibition of a setting by specification limitation Document Number: 002-04988 Rev. *C Page 83 of 198 S6E2C3 Series Pin Status Type List of Pin Behavior by Mode State A Function Group Power-On Reset or LowVoltage Detection State INITX Input State Device mode Internal Run or Sleep Reset mode State State Timer mode, RTC mode, or Stop mode State Deep Standby RTC Mode or Deep Standby Stop mode State Return from Deep Standby Mode State Power Supply Stable INITX = 1 - Power Power Supply Supply Stable Unstable ‐ INITX = 0 INITX = 1 ‐ ‐ ‐ Power Supply Stable INITX = 1 ‐ Power Supply Stable Power Supply Stable INITX = 1 SPL = 0 SPL = 1 GPIO selected Setting disabled Setting Setting disabled disabled Maintain previous state Maintain previous state HiZ/internal input fixed at 0 INITX = 1 SPL = 0 SPL = 1 GPIO Hiselected, Z/internal internal input fixed input fixed at 0 at 0 Main crystal oscillator input pin/ external main clock input selected Input enabled Input enabled Input enabled Input enabled Input enabled Input enabled Input enabled Input enabled Input Enabled Maintain previous state HiZ/internal input fixed at 0 GPIO selected, internal input fixed at 0 HiZ/internal input fixed at 0 GPIO selected Maintain previous state HiZ/internal input fixed at 0 Maintain previous state HiZ/internal input fixed at 0 Maintain previous State GPIO selected GPIO selected Setting disabled Setting Setting disabled disabled Maintain previous state External main clock input selected Setting disabled Setting Setting disabled disabled Maintain previous state Main crystal oscillator output pin Hi-Z/ internal input fixed at 0/ or input enable Hi-Z/ internal input fixed at 0 Hi-Z/ internal input fixed at 0 C INITX input pin Pull-up/ input enabled Pull-up/ Input enabled Pull-up/ Input enabled Pull-up/ Input enabled Pull-up/ Input enabled Pull-up/ Input enabled Pull-up/ Input enabled Pull-up/ Input enabled Pull-up/ Input enabled D Mode input pin Input enabled Input enabled Input enabled Input enabled Input enabled Input enabled Input enabled Input enabled Input enabled Mode input pin Input enabled Input enabled Input enabled Setting Setting disabled disabled Input enabled Hi-Z/ input enabled Input enabled Hi-Z/ input enabled Input enabled Setting disabled Input enabled Maintain previous state Input enabled GPIO selected Input enabled Maintain previous state B E Document Number: 002-04988 Rev. *C Maintain previous state while oscillator active/ When oscillation stops*1, it will be Hi-Z/ Internal input fixed at 0 GPIO selected GPIO selected Page 84 of 198 Pin Status Type S6E2C3 Series Function Group INITX Input State Device mode Internal Run or Sleep Reset mode State State Power Power Supply Supply Stable Unstable ‐ INITX = 0 INITX = 1 ‐ ‐ ‐ NMIX selected F Power-On Reset or LowVoltage Detection State Setting disabled Setting Setting disabled disabled Resource other than above selected GPIO selected Hi-Z Hi-Z/ input enabled Hi-Z/ input enabled JTAG selected Hi-Z Pull-up/ input enabled Pull-up/ input enabled G H I GPIO selected Setting disabled JTAG selected Hi-Z Resource other than above selected GPIO selected Resource selected GPIO selected Setting disabled Hi-Z Power Supply Stable INITX = 1 ‐ Setting Setting disabled disabled Pull-up/ input enabled Document Number: 002-04988 Rev. *C Maintain previous state Deep Standby RTC Mode or Deep Standby Stop mode State Return from Deep Standby Mode State Power Supply Stable Power Supply Stable INITX = 1 SPL = 0 SPL = 1 Maintain previous state Maintain previous Hi-Z/ state internal input fixed at 0 INITX = 1 SPL = 0 SPL = 1 Power Supply Stable INITX = 1 Maintain previous state Maintain previous state Pull-up/ input enabled Setting Setting disabled disabled Hi-Z/ input enabled Maintain previous state Timer mode, RTC mode, or Stop mode State Hi-Z/ input enabled Maintain previous state Maintain previous state Maintain previous state Maintain previous state WKUP input enabled Hi-Z/ WKUP input enabled Maintain previous state Maintain previous state Maintain previous state Maintain previous state Hi-Z/ internal input fixed at 0 GPIO selected, internal input fixed at 0 Hi-Z/ internal input fixed at 0 GPIO selected Maintain previous state Maintain previous state Maintain previous state Maintain previous state HiZ/Internal input fixed at 0 GPIO selected, internal input fixed at 0 HiZ/Internal input fixed at 0 GPIO selected HiZ/Internal input fixed at 0 GPIO selected, internal input fixed at 0 HiZ/internal input fixed at 0 GPIO selected GPIO selected Page 85 of 198 Pin Status Type S6E2C3 Series Function Group Power-On Reset or LowVoltage Detection State INITX Input State Device mode Internal Run or Sleep Reset mode State State Power Power Supply Supply Stable Unstable ‐ INITX = 0 INITX = 1 ‐ ‐ ‐ Power Supply Stable INITX = 1 ‐ Analog output selected J K External interrupt enable selected Resource other than above selected GPIO selected External interrupt enable selected Resource other than above selected GPIO selected Analog input selected Deep Standby RTC Mode or Deep Standby Stop mode State Return from Deep Standby Mode State Power Supply Stable Power Supply Stable INITX = 1 SPL = 0 SPL = 1 INITX = 1 SPL = 0 SPL = 1 Power Supply Stable INITX = 1 - *2 Hi-Z Setting disabled Hi-Z/ input enabled Hi-Z/ input enabled Hi-Z/ input enabled Hi-Z/ input enabled Hi-Z Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled Setting disabled Maintain previous state Setting Setting disabled disabled Document Number: 002-04988 Rev. *C *3 Maintain previous state Maintain previous state HiZ/internal input fixed at 0 Maintain previous state Setting Setting disabled disabled Hi-Z L Resource other than above selected GPIO selected Timer mode, RTC mode, or Stop mode State GPIO selected, internal input fixed at 0 HiZ/internal input fixed at 0 GPIO selected GPIO selected, internal input fixed at 0 HiZ/internal input fixed at 0 GPIO selected Maintain previous state Maintain previous state Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled Maintain previous state Maintain previous state HiZ/internal input fixed at 0 GPIO selected, internal input fixed at 0 HiZ/internal input fixed at 0 GPIO selected HiZ/internal input fixed at 0 Page 86 of 198 Pin Status Type S6E2C3 Series Function Group Analog input selected M Power-On Reset or LowVoltage Detection State INITX Input State Device mode Internal Run or Sleep Reset mode State State Power Power Power Supply Supply Supply Stable Unstable Stable ‐ INITX = 0 INITX = 1 INITX = 1 ‐ ‐ ‐ ‐ Hi-Z/ Hi-Z/ Hi-Z/ internal internal internal input input input fixed fixed fixed Hi-Z at 0/ at 0/ at 0/ analog analog analog input input input enabled enabled enabled External interrupt enable selected Resource other than above selected Timer mode, RTC mode, or Stop mode State Deep Standby RTC Mode or Deep Standby Stop mode State Return from Deep Standby Mode State Power Supply Stable Power Supply Stable INITX = 1 SPL = 0 SPL = 1 INITX = 1 SPL = 0 SPL = 1 Power Supply Stable INITX = 1 - Hi-Z/ internal input fixed at 0/ analog input enabled Maintain previous state Setting disabled Setting Setting disabled disabled Maintain previous state Maintain previous state Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled GPIO selected Analog input selected N Hi-Z Hi-Z/ internal input fixed at0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled Trace selected Resource other than above selected Hi-Z/ internal input fixed at 0/ analog input enabled HiZ/internal input fixed at 0 Hi-Z/ internal input fixed at 0/ analog input enabled Trace output Setting disabled Setting Setting disabled disabled GPIO selected Document Number: 002-04988 Rev. *C Maintain previous state Maintain previous state HiZ/internal input fixed at 0 Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled GPIO selected, internal input fixed at 0 HiZ/internal input fixed at 0 GPIO selected Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled GPIO selected, internal input fixed at 0 HiZ/internal input fixed at 0 GPIO selected Page 87 of 198 Pin Status Type S6E2C3 Series Function Group Analog input selected O Power-On Reset or LowVoltage Detection State INITX Input State Device mode Internal Run or Sleep Reset mode State State Power Power Power Supply Supply Supply Stable Unstable Stable ‐ INITX = 0 INITX = 1 INITX = 1 ‐ ‐ ‐ ‐ Hi-Z/ Hi-Z/ Hi-Z/ internal internal internal input input input fixed fixed fixed Hi-Z at 0/ at 0/ at 0/ analog analog analog input input input enabled enabled enabled Timer mode, RTC mode, or Stop mode State Deep Standby RTC Mode or Deep Standby Stop mode State Return from Deep Standby Mode State Power Supply Stable Power Supply Stable INITX = 1 SPL = 0 SPL = 1 INITX = 1 SPL = 0 SPL = 1 Power Supply Stable INITX = 1 - Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled GPIO selected, internal input fixed at 0 HiZ/internal input fixed at 0 GPIO selected Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled Maintain previous state WKUP input enabled Hi-Z/ WKUP input enabled HiZ/internal input fixed at 0 GPIO selected, internal input fixed at 0 HiZ/internal input fixed at 0 Trace selected Trace output External interrupt enable selected Maintain previous state Resource other than above selected Setting disabled Setting Setting disabled disabled Maintain previous state Maintain previous state HiZ/internal input fixed at 0 GPIO selected Analog input selected P Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled Hi-Z/ internal input fixed at 0/ analog input enabled WKUP enabled Resource other than above selected Setting disabled Setting Setting disabled disabled GPIO selected Document Number: 002-04988 Rev. *C Maintain previous state Maintain previous state GPIO selected Page 88 of 198 Pin Status Type S6E2C3 Series Function Group Power-On Reset or LowVoltage Detection State INITX Input State Device mode Internal Run or Sleep Reset mode State State Power Power Supply Supply Stable Unstable ‐ INITX = 0 INITX = 1 ‐ ‐ ‐ Power Supply Stable INITX = 1 ‐ Timer mode, RTC mode, or Stop mode State Deep Standby RTC Mode or Deep Standby Stop mode State Return from Deep Standby Mode State Power Supply Stable Power Supply Stable INITX = 1 SPL = 0 SPL = 1 INITX = 1 SPL = 0 SPL = 1 Hi-Z/ WKUP WKUP input input enabled enabled Power Supply Stable INITX = 1 - WKUP enabled Q External interrupt enable selected Resource other than above selected Setting disabled Maintain previous state Setting Setting disabled disabled Maintain previous state Hi-Z Hi-Z/ input enabled Hi-Z/ input enabled Hi-Z Hi-Z/ input enabled Hi-Z/ input enabled Maintain previous state HiZ/internal input fixed at 0 GPIO selected GPIO selected R USB I/O pin Setting disabled Setting Setting disabled disabled WKUP input enabled GPIO selected, internal input fixed at 0 HiZ/internal input fixed at 0 GPIO selected Maintain previous state Maintain previous state HiZ/internal input fixed at 0 GPIO selected, internal input fixed at 0 HiZ/internal input fixed at 0 GPIO selected Hi-Z at transmission/ input enabled/ internal input fixed at 0 at reception Hi-Z at transmission/ input enabled/ internal input fixed at 0 at reception Hi-Z at transmission/ input enabled/ internal input fixed at 0 at reception Hi-Z/ input enabled Hi-Z/ input enabled Hi-Z/ input enabled *1: Oscillation is stopped at sub Timer mode, sub CR Timer mode, RTC mode, Stop mode, Deep Standby RTC mode, and Deep Standby Stop mode. *2: Maintain previous state at Timer mode. GPIO selected internal input fixed at 0 at RTC mode, Stop mode. *3: Maintain previous state at Timer mode. Hi-Z/internal input fixed at 0 at RTC mode, Stop mode. *4: It shows the case selected by EPFR14.E_SPLC register. Document Number: 002-04988 Rev. *C Page 89 of 198 S6E2C3 Series VBAT Pin Status Type List of VBAT Domain Pin Status Function Group Poweron reset*1 Power Supply Unstable ‐ ‐ GPIO selected Device Internal Reset State Power Supply Stable INITX = 0 ‐ INITX = 1 ‐ Timer mode, RTC mode, or Stop mode State Power Supply Stable Power Supply Stable Power Supply Stable INITX = 1 ‐ INITX = 1 SPL = 0 SPL = 1 INITX = 1 SPL = 0 SPL = 1 Input enabled Input enabled Input enabled Input enabled Resource selected Hi-Z GPIO selected VBAT RTC Mode State Return From VBAT RTC Mode State Power Supply Stable Power Supply Stable Power Supply Stable INITX = 1 - - - Input enabled Input enabled Input enabled Input enabled Maintain previous state - Maintain previous state Maintain Maintain Maintain Maintain Maintain Maintain Maintain Maintain Setting Setting previous previous previous previous previous previous previous previous disabled prohibition state state state state state state state state External Maintain Maintain Maintain Maintain sub clock Setting previous previous previous previous input disabled state state state state selected T Maintain Hi-Z/ previous Sub internal Maintain Maintain Maintain state/ crystal input previous previous previous When oscillator fixed at 0/ state state state oscillation output pin or input stops, enable Hi-Z*2 U Return Deep Standby From RTC mode or Deep Deep Standby Stop Standby mode State Mode State Run mode or Sleep mode State Maintain Maintain Maintain Maintain Maintain Maintain Maintain Maintain Setting Setting previous previous previous previous previous previous previous previous disabled prohibition state state state state state state state state Sub crystal S oscillator input pin/ Input external enabled sub clock input selected GPIO selected INITX Input State - Maintain Maintain Maintain Maintain previous previous previous previous state state state state Maintain previous state Maintain previous state Maintain Maintain Maintain previous previous previous state/ state/ state/ Maintain When When When previous oscillation oscillation oscillation state stops, stops, stops, Hi-Z*2 Hi-Z*2 Hi-Z*2 Maintain previous state Maintain previous state Maintain Maintain Maintain Maintain Maintain Maintain Maintain Maintain previous previous previous previous previous previous previous previous state state state state state state state state Maintain previous state Maintain previous state *1: When VBAT and VCC power on. *2: When the SOSCNTL bit in the WTOSCCNT register is 0, the sub crystal oscillator output pin is maintained in the previous state. When the SOSCNTL bit in the WTOSCCNT register is 1, oscillation is stopped at Stop mode and Deep Standby Stop mode Document Number: 002-04988 Rev. *C Page 90 of 198 S6E2C3 Series 12. Electrical Characteristics 12.1 Absolute Maximum Ratings Parameter Symbol Power supply voltage*1,*2 Rating Min Max Unit VCC VSS - 0.5 VSS + 6.5 V Power supply voltage (for USB) *1,*3 USBVCC0 VSS - 0.5 VSS + 6.5 V Power supply voltage (for USB) *1,*3 USBVCC1 VSS - 0.5 VSS + 6.5 V VBAT AVCC AVRH VSS - 0.5 VSS - 0.5 VSS - 0.5 VSS + 6.5 VSS + 6.5 VSS + 6.5 VCC + 0.5 (≤ 6.5 V) USBVCC0 + 0.5 (≤ 6.5 V) USBVCC1 + 0.5 (≤ 6.5 V) V V V VSS + 6.5 Power supply voltage (VBAT) *1 ,*4 Analog power supply voltage *1 ,*5 Analog reference voltage *1 ,*5 VSS - 0.5 Input voltage *1 VI VSS - 0.5 VSS - 0.5 VSS - 0.5 Analog pin input voltage Output voltage *1 *1 L level maximum output current *6 L level average output current *7 L level total maximum output current L level total maximum output current*8 H level maximum output current *6 H level average output current *7 H level total maximum output current H level total average output current *8 Power consumption Storage temperature VIA VSS - 0.5 VO VSS - 0.5 IOL - IOLAV - ∑IOL ∑IOLAV - IOH - IOHAV - ∑IOH ∑IOHAV PD TSTG -55 Remarks V Except for USB pin V USB ch 0 pin V USB ch 1 pin V 5V tolerant AVCC + 0.5 (≤ 6.5 V) VCC + 0.5 (≤ 6.5 V) 10 20 10 20 22.4 4 8 10 12 20 100 50 -10 mA mA mA mA mA mA mA mA mA mA mA mA mA 4 mA type 8 mA type 10 mA type 12 mA type I2C Fm+ 4 mA type 8 mA type 10 mA type 12 mA type I2C Fm+ -20 mA 8 mA type -20 -20 -4 -8 -10 -12 -100 -50 200 + 150 mA mA mA mA mA mA mA mA mW °C 10 mA type 12 mA type 4 mA type 8 mA type 10 mA type 12 mA type V V 4 mA type *1: These parameters are based on the condition that VSS = AVSS = 0.0 V. *2: VCC must not drop below VSS - 0.5 V. *3: USBVCC0, USBVCC1 must not drop below VSS - 0.5 V. *4: VBAT must not drop below VSS - 0.5 V. *5: Ensure that the voltage does not exceed VCC + 0.5 V, for example, when the power is turned on. *6: The maximum output current is defined as the value of the peak current flowing through any one of the corresponding pins. Document Number: 002-04988 Rev. *C Page 91 of 198 S6E2C3 Series *7: The average output current is defined as the average current value flowing through any one of the corresponding pins for a 100-ms period. *8: The total average output current is defined as the average current value flowing through all of corresponding pins for a 100-ms period. WARNING: − Semiconductor devices may be permanently damaged by application of stress (including, without limitation, voltage, current or temperature) in excess of absolute maximum ratings. Do not exceed any of these ratings. Document Number: 002-04988 Rev. *C Page 92 of 198 S6E2C3 Series 12.2 Recommended Operating Conditions Parameter Power supply voltage Power supply voltage (for USB ch 0) Power supply voltage (for USB ch 1) Power supply voltage (VBAT) Analog power supply voltage Analog reference voltage Operating temperature Junction temperature Ambient temperature Symbol Conditions VCC - USBVCC0 USBVCC1 VBAT AVCC AVRH AVRL TJ TA Min 2.7 *7 Value 3.0 3.6 ( ≤VCC) 2.7 5.5 ( ≤VCC) 3.0 3.6 ( ≤VCC) 2.7 5.5 ( ≤VCC) 1.65 2.7 *6 AVSS -40 -40 5.5 5.5 AVCC AVSS + 125 *5 - - - Max 5.5 Unit Remarks V *1 V *2 *3 V *4 V V V V °C °C AVCC = VCC *1: When P81/UDP0 and P80/UDM0 pins are used as USB (UDP0, UDM0) *2: When P81/UDP0 and P80/UDM0 pins are used as GPIO (P81, P80) *3: When P83/UDP1 and P82/UDM1 pins are used as USB (UDP1, UDM1) *4: When P83/UDP1 and P82/UDM1 pins are used as GPIO (P83, P82) *5: The maximum temperature of the ambient temperature (TA) can guarantee a range that does not exceed the junction temperature (TJ). The calculation formula of the ambient temperature (TA) is: TA (Max) = TJ(Max) - Pd(Max) × θJA Pd: Power dissipation (W) θJA: Package thermal resistance (°C/W) Pd (Max) = VCC × ICC (Max) + Σ (IOL×VOL) + Σ ((VCC-VOH) × (- IOH)) IOL: L level output current IOH: H level output current VOL: L level output voltage VOH: H level output voltage *6: The minimum value of analog reference voltage depends on the value of compare clock cycle (tCCK). See 12.5. 12-bit A/D Converter for the details. *7: For the voltage range between Vcc(min) and the low voltage detection reset (VDH), the MCU must be clocked from either the High-speed CR or the low-speed CR.” Document Number: 002-04988 Rev. *C Page 93 of 198 S6E2C3 Series Package thermal resistance and maximum permissible power for each package are shown below. The operation is guaranteed maximum permissible power or less for semiconductor devices. Table for Package Thermal Resistance and Maximum Permissible Power Thermal Maximum Permissible Power Printed Circuit Resistance (mW) Package Board θJA TA = +85 °C TA = +105 °C (°C/W) Single-layered 48 833 417 LQS144 both sides (0.5-mm pitch) 4 layers 33 1212 606 Single-layered 45 889 444 LQP176 both sides (0.5-mm pitch) 4 layers 31 1290 645 Single-layered 46 870 435 LQQ216 both sides (0.4-mm pitch) 4 layers 32 1250 625 Single-layered LBE192 both sides (0.8-mm pitch) 4 layers 35 1143 571 WARNING: 1. The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device's electrical characteristics are warranted when the device is operated within these ranges. 2. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. 3. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. 4. Users considering application outside the listed conditions are advised to contact their representatives beforehand. Document Number: 002-04988 Rev. *C Page 94 of 198 S6E2C3 Series Calculation Method of Power Dissipation (Pd) The power dissipation is shown in the following formula. Pd = VCC × ICC + Σ (IOL × VOL) + Σ ((VCC-VOH) × (-IOH)) IOL: L level output current IOH: H level output current VOL:L level output voltage VOH:H level output voltage ICC is the current drawn by the device. It can be analyzed as follows. ICC = ICC (INT) + ΣICC (IO) ICC (INT): Current drawn by internal logic and memory, etc. through the regulator ΣICC (IO): Sum of current (I/O switching current) drawn by the output pin For ICC (INT), it can be anticipated by (1) Current Rating in 12.3. DC Characteristics (This rating value does not include ICC (IO) for a value at pin fixed). For Icc (IO), it depends on system used by customers. The calculation formula is shown below. ICC (IO) = (CINT + CEXT) × VCC × fSW CINT: Pin internal load capacitance CEXT: External load capacitance of output pin fSW: Pin switching frequency Parameter Symbol Pin internal load capacitance CINT Conditions Capacitance Value 4 mA type 1.93 pF 8 mA type 3.45 pF 12 mA type 3.42 pF Calculate ICC (Max) as follows when the power dissipation can be evaluated by yourself: Measure current value ICC (Typ) at normal temperature (+25 °C). Add maximum leakage current value ICC (leak_max) at operating on a value in (1). ICC(Max) = ICC (Typ) + ICC (leak_max) Parameter Symbol Maximum leakage current at operating Conditions TJ = +125 °C Current Value 79.2 mA ICC (leak_max) TJ = +105 °C 39.4 mA TJ = +85 °C 26.5 mA Document Number: 002-04988 Rev. *C Page 95 of 198 S6E2C3 Series Current Explanation Diagram Pd=VCC×ICC + Σ(IOL×VOL)＋Σ((VCC-VOH)×(－IOH)) ICC=ICC (INT)＋ΣICC (IO) VCC A ICC Chip ICC (INT) ΣICC (IO) A Regulator VOL V A ・・・ V IOL Flash VOH ・・・ Logic IOH RAM ICC (IO) CEXT ・・・ Document Number: 002-04988 Rev. *C Page 96 of 198 S6E2C3 Series 12.3 DC Characteristics 12.3.1 Current Rating Table 12-1 Typical and Maximum Current Consumption in Normal Operation (PLL), Code Running from Flash Memory (Flash Accelerator Mode and Trace Buffer Function Enabled) Parameter Symbol Pin Name Frequency*4 Conditions *5 *6 Power supply current ICC VCC Normal operation *7,*8 (PLL) *5 *6 200 MHz 192 MHz 180 MHz 160 MHz 144 MHz 120 MHz 100 MHz 80 MHz 60 MHz 40 MHz 20 MHz 8 MHz 4 MHz 200 MHz 192 MHz 180 MHz 160 MHz 144 MHz 120 MHz 100 MHz 80 MHz 60 MHz 40 MHz 20 MHz 8 MHz 4 MHz Value Typ* 117 113 106 95 86 73 61 50 39 27 16 8.7 6.4 71 68 64 58 52 44 38 31 24 17 10 6.3 5.0 1 Max*2 224 219 211 197 186 169 155 140 126 112 97 88.9 86.1 168 165 159 151 144 134 126 117 109 100 91 86.1 84.5 Unit mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA Remarks *3 When all peripheral clocks are on *3 When all peripheral clocks are off *1: TA = +25 °C, VCC = 3.3 V *2: TJ = +125 °C, VCC = 5.5 V *3: When all ports are fixed *4: Frequency is a value of HCLK when PCLK0 = PCLK1 = PCLK2 = HCLK *5: When stopping flash accelerator mode and trace buffer function (FRWTR.RWT = 11, FBFCR.BE = 1) *6: When stopping flash accelerator mode and trace buffer function (FRWTR.RWT = 10, FBFCR.BE = 1) *7: Firmware being executed during data collection for this table is not being accessed from the MainFlash memory.” *8: When using the crystal oscillator of 4 MHz (including the current consumption of the oscillation circuit) Document Number: 002-04988 Rev. *C Page 97 of 198 S6E2C3 Series Table 12-2 Typical and Maximum Current Consumption in Normal Operation (PLL), Code with Data Accessing Running from Flash Memory (Flash Accelerator Mode and Trace Buffer Function Disabled) Parameter Symbol Pin Name Frequency*4 Conditions *5 *6 Power supply current ICC VCC Normal operation *7,*8 (PLL) *5 *6 200 MHz 192 MHz 180 MHz 160 MHz 144 MHz 120 MHz 100 MHz 80 MHz 60 MHz 40 MHz 20 MHz 8 MHz 4 MHz 200 MHz 192 MHz 180 MHz 160 MHz 144 MHz 120 MHz 100 MHz 80 MHz 60 MHz 40 MHz 20 MHz 8 MHz 4 MHz Value Typ*1 Max*2 128 123 116 102 93 79 67 54 42 30 17 9.2 6.7 74 71 67 59 53 45 39 32 25 18 11 6.5 5.1 236 230 221 205 193 175 161 145 130 115 99 90.0 86.9 170 167 162 152 145 135 127 118 110 101 92 86.8 85.0 Unit mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA Remarks *3 When all peripheral clocks are on *3 When all peripheral clocks are off *1: TA = +25 °C, VCC = 3.3 V *2: TJ = +125 °C, VCC = 5.5 V *3: When all ports are fixed *4: Frequency is a value of HCLK when PCLK0 = PCLK1 = PCLK2 = HCLK *5: When stopping flash accelerator mode and trace buffer function (FRWTR.RWT = 11, FBFCR.BE = 0) *6: When stopping flash accelerator mode and trace buffer function (FRWTR.RWT = 10, FBFCR.BE = 0) *7: With data access to a MainFlash memory. *8: When using the crystal oscillator of 4 MHz (including the current consumption of the oscillation circuit) Document Number: 002-04988 Rev. *C Page 98 of 198 S6E2C3 Series Table 12-3 Typical and Maximum Current Consumption in Normal Operation (PLL), Code with Data Accessing Running from Flash Memory (Flash 0 Wait-cycle Mode and Read Access 0 Wait) Parameter Symbol Pin Name Frequency*4 Conditions *5 Power supply current ICC VCC Normal operation *6,*7 (PLL) *5 72 MHz 60 MHz 48 MHz 36 MHz 24 MHz 12 MHz 8 MHz 4 MHz 72 MHz 60 MHz 48 MHz 36 MHz 24 MHz 12 MHz 8 MHz 4 MHz Value Typ* 71 62 51 40 29 17 13 8.4 46 41 34 27 20 12 9.4 6.5 1 Max*2 161 150 138 125 112 98 93 88.5 132 125 118 110 102 93 89.7 86.4 Unit mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA Remarks *3 When all peripheral clocks are on *3 When all peripheral clocks are off *1: TA = +25 °C, VCC = 3.3 V *2: TJ = +125 °C, VCC = 5.5 V *3: When all ports are fixed *4: Frequency is a value of HCLK when PCLK0 = PCLK1 = PCLK2 = HCLK *5: When operating flash 0 wait-cycle mode and read access 0 wait (FRWTR.RWT = 00, FBFCR.SD = 000) *6: With data access to a MainFlash memory. *7: When using the crystal oscillator of 4 MHz (including the current consumption of the oscillation circuit) Document Number: 002-04988 Rev. *C Page 99 of 198 S6E2C3 Series Table 12-4 Typical and Maximum Current Consumption in Normal Operation (Other Than PLL), Code with Data Accessing Running from Flash Memory (Flash 0 Wait-cycle Mode and Read Access 0 Wait) Parameter Symbol Pin Name Normal operation *6, *7 (main oscillation) Power supply current Normal operation *6 (built-in High-speed CR) ICC Frequency*4 Conditions *5 *5 Value Typ*1 Max*2 Unit 4.7 84.9 mA 3.9 83.8 mA 3.0 83.2 mA 2.1 82.0 mA 0.78 80.37 mA 0.77 80.36 mA 0.81 80.39 mA 0.78 80.38 mA 4 MHz 4 MHz VCC Normal operation *6, *8 (sub oscillation) Normal operation *6 (built-in low-speed CR) *5 *5 32 kHz 100 kHz Remarks *3 When all peripheral clocks are on *3 When all peripheral clocks are off *3 When all peripheral clocks are on *3 When all peripheral clocks are off *3 When all peripheral clocks are on *3 When all peripheral clocks are off *3 When all peripheral clocks are on *3 When all peripheral clocks are off *1: TA = +25 °C, VCC = 3.3 V *2: TJ = +125 °C, VCC = 5.5 V *3: When all ports are fixed *4: Frequency is a value of HCLK when PCLK0 = PCLK1 = PCLK2 = HCLK/2 *5: When operating flash 0 wait-cycle mode and read access 0 wait (FRWTR.RWT = 00, FBFCR.SD = 000) *6: With data access to a MainFlash memory. *7: When using the crystal oscillator of 4 kHz (including the current consumption of the oscillation circuit) *8: When using the crystal oscillator of 32 kHz (including the current consumption of the oscillation circuit) Document Number: 002-04988 Rev. *C Page 100 of 198 S6E2C3 Series Table 12-5 Typical and Maximum Current Consumption in Sleep Operation (PLL), when PCLK0 = PCLK1 = PCLK2 = HCLK/2 Parameter Power supply current Symbol ICCS Pin Name VCC Conditions Frequency*4 Sleep operation*5 (PLL) 200 MHz 192 MHz 180 MHz 160 MHz 144 MHz 120 MHz 100 MHz 80 MHz 60 MHz 40 MHz 20 MHz 8 MHz 4 MHz 200 MHz 192 MHz 180 MHz 160 MHz 144 MHz 120 MHz 100 MHz 80 MHz 60 MHz 40 MHz 20 MHz 8 MHz 4 MHz Value Typ*1 Max*2 88 85 80 72 65 55 47 38 30 21 12 7.4 5.8 44 42 40 36 33 28 24 20 16 12 7.6 5.2 4.4 188 184 178 164 156 144 134 124 114 104 93 87.2 85.2 134 132 129 123 119 113 108 103 98 93 87.6 84.7 83.7 Unit mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA Remarks *3 When all peripheral clocks are on *3 When all peripheral clocks are off *1: TA = +25 °C, VCC = 3.3 V *2: TJ = +125 °C, VCC = 5.5 V *3: When all ports are fixed *4: Frequency is a value of HCLK when PCLK0 = PCLK1 = PCLK2 = HCLK/2 *5: When using the crystal oscillator of 4 MHz (including the current consumption of the oscillation circuit) Document Number: 002-04988 Rev. *C Page 101 of 198 S6E2C3 Series Table 12-6 Typical and Maximum Current Consumption in Sleep Operation (PLL), when PCLK0 = PCLK1 = PCLK2 = HCLK Parameter Power supply current Symbol ICCS Pin Name VCC Conditions Frequency*4 Sleep operation*5 (PLL) 72 MHz 60 MHz 48 MHz 36 MHz 24 MHz 12 MHz 8 MHz 4 MHz 72 MHz 60 MHz 48 MHz 36 MHz 24 MHz 12 MHz 8 MHz 4 MHz Value Typ* 45 38 31 24 18 11 8.6 6.3 20 18 15 12 9.1 6.5 5.5 4.6 1 Max*2 130 122 114 106 99 91 88.3 85.7 103 99 96 93 89.3 86.1 84.9 83.8 Unit mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA Remarks *3 When all peripheral clocks are on *3 When all peripheral clocks are off *1: TA = +25 °C, VCC = 3.3 V *2: TJ = +125 °C, VCC = 5.5 V *3: When all ports are fixed *4: Frequency is a value of HCLK when PCLK0 = PCLK1 = PCLK2 = HCLK *5: When using the crystal oscillator of 4 MHz (including the current consumption of the oscillation circuit) Document Number: 002-04988 Rev. *C Page 102 of 198 S6E2C3 Series Table 12-7 Typical and Maximum Current Consumption in Sleep Operation (Other Than PLL), when PCLK0 = PCLK1 = PCLK2 = HCLK/2 Parameter Symbol Pin Name Conditions Sleep operation*5 (main oscillation) Power supply current Sleep operation (built-in High-speed CR) ICCS Frequency*4 Value Unit Typ*1 Max*2 3.4 82.6 mA 2.5 81.7 mA 2.5 81.7 mA 1.7 80.9 mA 0.75 79.97 mA 0.74 79.96 mA 0.79 80.01 mA 0.76 79.98 mA 4 MHz 4 MHz VCC Sleep operation*6 (sub oscillation) Sleep operation (built-in low-speed CR) 32 kHz 100 kHz Remarks *3 When all peripheral clocks are on *3 When all peripheral clocks are off *3 When all peripheral clocks are on *3 When all peripheral clocks are off *3 When all peripheral clocks are on *3 When all peripheral clocks are off *3 When all peripheral clocks are on *3 When all peripheral clocks are off *1: TA = +25 °C, VCC = 3.3 V *2: TJ = +125 °C, VCC = 5.5 V *3: When all ports are fixed. *4: Frequency is a value of HCLK when PCLK0 = PCLK1 = PCLK2 = HCLK/2 *5: When using the crystal oscillator of 4 MHz (including the current consumption of the oscillation circuit) *6: When using the crystal oscillator of 32 kHz (including the current consumption of the oscillation circuit) Document Number: 002-04988 Rev. *C Page 103 of 198 S6E2C3 Series Table 12-8 Typical and Maximum Current Consumption in Stop Mode, Timer Mode and RTC Mode Parameter Symbol Pin Name Conditions Stop mode ICCH Timer mode*5 (main oscillation) Timer mode (built-in High-speed CR) Power supply current ICCT Frequency - 4 MHz 4 MHz VCC Timer mode*6 (sub oscillation) Timer mode (built-in Low-speed CR) ICCR RTC mode*6 (sub oscillation) 32 kHz 100 kHz 32 kHz Value Typ*1 Max*2 Unit Remarks 0.56 3.01 mA *3, *4 TA = +25 °C - 27.03 mA *3, *4 TA = +85 °C - 39.92 mA *3, *4 TA = +105 °C 1.40 3.85 mA *3, *4 TA = +25 °C - 27.87 mA *3, *4 TA = +85 °C - 40.76 mA *3, *4 TA = +105 °C 0.95 3.40 mA *3, *4 TA = +25 °C - 27.42 mA *3, *4 TA = +85 °C - 40.31 mA *3, *4 TA = +105 °C 0.57 3.02 mA *3, *4 TA = +25 °C - 27.04 mA *3, *4 TA = +85 °C - 39.93 mA *3, *4 TA = +105 °C 0.58 3.03 mA *3, *4 TA = +25 °C - 27.05 mA *3, *4 TA = +85 °C - 39.94 mA *3, *4 TA = +105 °C 0.57 3.02 mA *3, *4 TA = +25 °C - 27.04 mA *3, *4 TA = +85 °C - 39.93 mA *3, *4 TA = +105 °C *1: VCC = 3.3 V *2: VCC = 5.5 V *3: When all ports are fixed *4: When LVD is off *5: When using the crystal oscillator of 4 MHz (including the current consumption of the oscillation circuit) *6: When using the crystal oscillator of 32 kHz (including the current consumption of the oscillation circuit) Document Number: 002-04988 Rev. *C Page 104 of 198 S6E2C3 Series Table 12-9 Typical and Maximum Current Consumption in Deep Standby Stop Mode, Deep Standby RTC Mode and VBAT Parameter Symbol Pin Name Conditions Deep Standby Stop mode (When RAM is off) Frequency - Value Typ* 1 Max*2 Unit 96 248 µA *3, *4 TA = +25 °C - 3009 µA *3, *4 TA = +85 °C - 3889 µA *3, *4 TA = +105 °C 106 259 µA *3, *4 TA = +25 °C - 3020 µA *3, *4 TA = +85 °C - 3900 µA *3, *4 TA = +105 °C 96 248 µA *3, *4 TA = +25 °C - 3009 µA *3, *4 TA = +85 °C - 3889 µA *3, *4 TA = +105 °C 106 259 µA *3, *4 TA = +25 °C - 3020 µA *3, *4 TA = +85 °C - 3900 µA *3, *4 TA = +105 °C 0.058 0.1 µA *3, *4, *5 TA = +25 °C - 1.4 µA *3, *4, *5 TA = +85 °C - 3.3 µA *3, *4, *5 TA = +105 °C 1.0 1.8 µA *3, *4 TA = +25 °C - 3.2 µA *3, *4 TA = +85 °C - 5.1 µA *3, *4 TA = +105 °C ICCHD Deep Standby Stop mode (When RAM is on) - VCC Deep Standby RTC mode (When RAM is off) Power supply current 32 kHz ICCRD Deep Standby RTC mode (When RAM is on) RTC stop*6 ICCVBAT VBAT - RTC operation*6 Remarks *1: VCC = 3.3 V *2: VCC = 5.5 V *3: When all ports are fixed *4: When LVD is off *5: When sub oscillation is off *6: In the case of setting RTC after VCC power on Document Number: 002-04988 Rev. *C Page 105 of 198 S6E2C3 Series Table 12-10 Typical and Maximum Current Consumption in Low-voltage Detection Circuit, Main Flash Memory Write/erase Parameter Low-voltage detection circuit (LVD) power supply current MainFlash memory write/erase current Symbol Pin Name ICCLVD Min Value Typ Max At operation - 4 At write/erase - 13.4 Conditions Unit Remarks 7 µA For occurrence of interrupt 15.9 mA *1 VCC ICCFLASH *1: When programming or erase in flash memory, Flash Memory Write/Erase current (ICCFLASH) is added to the Power supply current (ICC). Peripheral Current Dissipation Clock system HCLK PCLK1 PCLK2 Frequency (MHz) Peripheral Unit GPIO 50 100 200 All ports 0.39 0.81 1.56 DMAC - 0.99 1.97 3.82 DSTC - 0.73 1.49 2.86 External bus I/F - 0.25 0.48 0.97 SD card I/F - 0.74 1.47 2.90 USB 1 ch 0.48 0.95 1.89 I2 S - 0.51 1.02 1.99 High-Speed Quad SPI - 0.48 0.97 1.49 Programmable CRC - 0.05 0.10 0.22 Base timer 4 ch 0.21 0.42 0.83 1 unit/4 ch 0.83 1.65 3.25 1 unit 0.07 0.13 0.27 A/D converter 1 unit 0.31 0.60 1.17 Multi-function serial 1 ch 0.41 0.81 - Multi-functional timer/PPG Quadrature position/revolution counter Document Number: 002-04988 Rev. *C Unit Remarks mA mA mA Page 106 of 198 S6E2C3 Series 12.3.2 Pin Characteristics (VCC = USBVCC0 = USBVCC1 = AVCC = 2.7 V to 5.5 V, VSS = AVSS = 0 V) Parameter H level input voltage (hysteresis input) L level input voltage (hysteresis input) Symbol VIHS VILS Pin Name Conditions CMOS hysteresis input pin, MD0, MD1 MADATAxx 5 V tolerant input pin Input pin doubled as I2C Fm+ TTL Schmitt input pin CMOS hysteresis input pin, MD0, MD1 5 V tolerant input pin Input pin doubled as I2C Fm+ TTL Schmitt input pin Value Unit Remarks Min Typ Max - VCC × 0.8 - VCC + 0.3 V VCC > 3.0 V, VCC ≤ 3.6 V, 2.4 - VCC + 0.3 V - VCC × 0.8 - VSS + 5.5 V - VCC × 0.7 - VSS + 5.5 V - 2.0 - VCC+0.3 V - VSS - 0.3 - VCC×0.2 V - VSS - 0.3 - VCC×0.2 V - VSS - VCC×0.3 V - VSS - 0.3 - 0.8 V VCC - 0.5 - VCC V VCC - 0.5 - VCC V VCC - 0.5 - VCC V VCC - 0.5 - VCC V USBVCC - 0.4 - USBVCC V *1 VCC - 0.5 - VCC V At GPIO At External Bus VCC ≥ 4.5 V, IOH = -4 mA 4 mA type VCC < 4.5 V, IOH = -2 mA VCC ≥ 4.5 V, IOH = -8 mA 8 mA type H level output voltage 10 mA type VOH 12 mA type The pin doubled as USB I/O The pin doubled as I2C Fm+ Document Number: 002-04988 Rev. *C VCC < 4.5 V, IOH = -4 mA VCC ≥ 4.5 V, IOH = -10 mA VCC < 4.5 V, IOH = -8 mA VCC ≥ 4.5 V, IOH = -12 mA VCC < 4.5 V, IOH = -8 mA USBVCC ≥ 4.5 V, IOH = -20.5 mA USBVCC < 4.5 V, IOH = -13.0 mA VCC ≥ 4.5 V, IOH = -4 mA VCC < 4.5 V, IOH = -3 mA Page 107 of 198 S6E2C3 Series Parameter Symbol Pin Name Conditions Value Unit Min Typ Max VSS - 0.4 V VSS - 0.4 V VSS - 0.4 V VSS - 0.4 V VSS - 0.4 V VSS - 0.4 V Remarks VCC ≥ 4.5 V, IOL = 4 mA 4 mA type VCC < 4.5 V, IOL = 2 mA VCC ≥ 4.5 V, IOL = 8 mA 8 mA type L level output voltage 10 mA type VOL 12 mA type The pin doubled as USB I/O The pin doubled as I2C Fm+ Input leak current Pull-up resistor value Input capacitance IIL - RPU Pull-up pin CIN Other than VCC, USBVCC0, USBVCC1, VBAT, VSS, AVCC, AVSS, AVRH VCC < 4.5 V, IOL = 4 mA VCC ≥ 4.5 V, IOL = 10 mA VCC < 4.5 V, IOL = 8 mA VCC ≥ 4.5 V, IOL = 12 mA VCC < 4.5 V, IOL = 8 mA USBVCC ≥ 4.5 V, IOL = 18.5 mA USBVCC < 4.5 V, IOL = 10.5 mA VCC ≥ 4.5 V, IOL = 4 mA VCC < 4.5 V, IOL = 3 mA VCC ≤ 4.5 V, IOL = 20 mA *1 At GPIO At I2C Fm+ - -5 - +5 VCC ≥ 4.5 V 25 50 100 VCC < 4.5 V 30 80 200 - - 5 15 μA kΩ pF *1: USBVcc0 and USBVcc1 are described as USBVcc. Document Number: 002-04988 Rev. *C Page 108 of 198 S6E2C3 Series 12.4 AC Characteristics 12.4.1 Main Clock Input Characteristics (VCC = AVCC = 2.7 V to 5.5 V, VSS = AVSS = 0 V, Ta = -40 C to +105 C) Parameter Input frequency Input clock cycle Symbol tCYLH tCF, tCR fCC Internal operating clock *1 frequency fCP0 fCP1 fCP2 tCYCC tCYCP0 tCYCP1 tCYCP2 Value Max VCC ≥4.5 V VCC < 4.5 V VCC ≥4.5 V VCC < 4.5 V VCC ≥4.5 V VCC < 4.5 V PWH/tCYLH, PWL/tCYLH 4 4 4 4 20.83 50 48 20 48 20 250 250 45 - X0, X1 - Input clock rise time and fall time Conditions Min fCH Input clock pulse width Internal operating clock *1 cycle time Pin Name Unit Remarks MHz When crystal oscillator is connected MHz When using external clock ns When using external clock 55 % When using external clock - 5 ns When using external clock - - 200 MHz Base clock (HCLK/FCLK) - 5 10 5 10 100 200 100 - MHz MHz MHz ns ns ns ns APB0bus clock *2 APB1bus clock *2 APB2bus clock *2 Base clock (HCLK/FCLK) APB0bus clock *2 APB1bus clock *2 APB2bus clock *2 *1: For more information about each internal operating clock, see "CHAPTER 2-1: Clock" in FM4 Family Peripheral Manual Main Part (002-04856). *2: For more about each APB bus to which each peripheral is connected, see 8. Block Diagram in this data sheet. X0 Document Number: 002-04988 Rev. *C Page 109 of 198 S6E2C3 Series 12.4.2 Sub Clock Input Characteristics (VBAT = 1.65 V to 5.5 V, VSS = 0 V) Parameter Symbol Input frequency Pin Name Value Conditions Unit Min Typ Max - - 32.768 - kHz - 32 - 100 kHz - 10 - 31.25 μs PWH/tCYLL, PWL/tCYLL 45 - 55 % 1/tCYLL Input clock cycle tCYLL Input clock pulse width X0A, X1A - Remarks When crystal oscillator is connected * When using external clock When using external clock When using external clock *: For more information about crystal oscillator, see Sub crystal oscillator in 7. Handling Devices. tCYLL 0.8 × VBAT 0.8 × VBAT X0A PWH 12.4.3 0.8 × VBAT 0.2 × VBAT 0.2 × VBAT PWL Built-In CR Oscillation Characteristics Built-In High-speed CR (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Clock frequency Frequency stabilization time Symbol fCRH Value Conditions Min Typ Max TJ = - 20°C to + 105°C 3.92 4 4.08 TJ = - 40°C to + 125°C 3.88 4 4.12 TJ = - 40°C to + 125°C 3 4 5 - - - 30 tCRWT Unit Remarks When trimming *1 MHz When not trimming μs *2 *1: In the case of using the values in CR trimming area of flash memory at shipment for frequency/temperature trimming *2: This is the time to stabilize the frequency of the High-speed CR clock after setting trimming value. During this period, it is able to use the High-speed CR clock as a source clock. Built-In Low-speed CR (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol Condition Clock frequency fCRL - Document Number: 002-04988 Rev. *C Value Min Typ Max 50 100 150 Unit Remarks kHz Page 110 of 198 S6E2C3 Series 12.4.4 Operating Conditions of Main PLL (in the Case of Using Main Clock for Input Clock of PLL) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Min Value Typ Max tLOCK 100 - - μs fPLLI fPLLO 4 13 200 - - 16 100 400 200 MHz multiplier MHz MHz Symbol time*1 PLL oscillation stabilization wait (lock up time) PLL input clock frequency PLL multiplication rate PLL macro oscillation clock frequency Main PLL clock frequency*2 fCLKPLL Unit Remarks *1: Time from when the PLL starts operating until the oscillation stabilizes *2: For more information about Main PLL clock (CLKPLL), see Chapter 2-1: Clock in FM4 Family Peripheral Manual Main Part (002-04856). 12.4.5 Operating Conditions of USB PLL・I2S PLL (in the Case of Using Main Clock for Input Clock of PLL) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter PLL oscillation stabilization wait time (lock up time) PLL input clock frequency PLL multiplication rate *1 PLL macro oscillation clock frequency USB clock frequency *2 I2S clock frequency *3 Min Value Typ Max tLOCK 100 - - μs fPLLI - 4 13 - fPLLO 200 - 16 100 400 384 MHz multiplier MHz MHz fCLKPLL - - 50 MHz fCLKPLL - - 12.288 MHz Symbol Unit Remarks USB I 2S After the M frequency division After the M frequency division *1: Time from when the PLL starts operating until the oscillation stabilizes *2: For more information about USB/Ethernet clock, see Chapter 2-2: USB/Ethernet Clock Generation in FM4 Family Peripheral Manual Communication Macro Part (002-04862). *3: For more information about I2S clock, see Chapter 7-1: I2S Clock Generation in FM4 Family Peripheral Manual Communication Macro Part (002-04862). Document Number: 002-04988 Rev. *C Page 111 of 198 S6E2C3 Series 12.4.6 Operating Conditions of Main PLL (in the Case of Using Built-in High-speed CR Clock for Input Clock of Main PLL) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Min Value Typ Max tLOCK 100 - - µs fPLLI fPLLO 3.8 50 190 4 - 4.2 95 400 MHz multiplier MHz fCLKPLL - - 200 MHz Symbol *1 PLL oscillation stabilization wait time (lock up time) PLL input clock frequency PLL multiplication rate PLL macro oscillation clock frequency Main PLL clock frequency *2 Unit Remarks *1: Time from when the PLL starts operating until the oscillation stabilizes *2: For more information about Main PLL clock (CLKPLL), see Chapter 2-1: Clock in FM4 Family Peripheral Manual Main Part (002-04856). Note: − The High-speed CR clock (CLKHC) should be set with frequency/temperature trimming to act as the source clock of the Main PLL. 12.4.7 Reset Input Characteristics (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Reset input time Symbol Pin Name Conditions tINITX INITX - Document Number: 002-04988 Rev. *C Value Min Typ 500 - Unit Remarks ns Page 112 of 198 S6E2C3 Series Power-On Reset Timing 12.4.8 (VSS = 0 V) Pin Symbol Name Parameter Power supply shut down time dV/dt Time until releasing Power-on reset VCC Unit Min Typ Max - 1 - - VCC: 0.2 V to 2.70 V 0.6 - 1000 - 0.33 - 0.60 tOFF Power ramp rate Value Conditions tPRT ms Remarks *1 mV/µs *2 ms *1: VCC must be held below 0.2 V for a minimum period of tOFF. Improper initialization may occur if this condition is not met. *2: This dV/dt characteristic is applied at the power-on of cold start (tOFF>1ms). Note: − If tOFF cannot be satisfied designs must assert external reset(INITX) at power-up and at any brownout event per 12. 4. 7. 2.7V VCC VDH 0.2V 0.2V dV/dt tPRT Internal RST 0.2V tOFF release RST Active CPU Operation start Glossary  VDH: 12.4.9 detection voltage of Low Voltage detection reset. See “12.8. Low-Voltage Detection Characteristics”. GPIO Output Characteristics (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Output frequency Symbol Pin Name tPCYCLE Pxx* Conditions Value Unit Min Typ VCC ≥ 4.5 V - 50 MHz VCC < 4.5 V - 32 MHz Remarks *: GPIO is a target. Pxx tPCYCLE Document Number: 002-04988 Rev. *C Page 113 of 198 S6E2C3 Series 12.4.10 External Bus Timing External Bus Clock Output Characteristics Parameter Symbol Pin Name tCYCLE MCLKOUT *1 Output frequency Value Conditions Min Typ - 50 *2 Unit Remarks MHz *1: The external bus clock (MCLKOUT) is a divided clock of HCLK. For more information about setting of clock divider, see Chapter 14: External Bus Interface in FM4 Family Peripheral Manual Main Part (002-04856). *2: Generate MCLKOUT at setting more than four divisions when the AHB bus clock exceeds 100 MHz. 0.8 × Vcc 0.8 × Vcc MCLK tCYCLE External Bus Signal I/O Characteristics (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol Signal input characteristics Conditions VIH VIL - VOH Value Unit 0.8 × VCC V 0.2 × VCC V 0.8 × VCC V 0.2 × VCC V Remarks Signal output characteristics VOL Input signal VIH VIL VIH VIL VOH VOL VOH VOL Document Number: 002-04988 Rev. *C Page 114 of 198 S6E2C3 Series Separate Bus Access Asynchronous SRAM Mode (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol Pin Name Conditions tOEW MOEX MCSX↓→Address output delay time tCSL – AV MOEX↑→Address hold time tOEH - AX MCSX↓→ MOEX↓delay time tCSL - OEL MOEX↑→ MCSX↑time tOEH - CSH MOEX Minimum pulse width MCSX↓→ MDQM↓delay time Value Unit Min Max - MCLK×n-3 - ns MCSX[7: 0], MAD[24: 0] - -9 +9 ns MOEX, MAD[24: 0] - 0 MCLK×m+9 ns - MCLK×m-9 MCLK×m+9 ns - 0 MCLK×m+9 ns MOEX, MCSX[7: 0] tCSL - RDQML MCSX, MDQM[3: 0] - MCLK×m-9 MCLK×m+9 ns Data set up→MOEX↑ time tDS - OE MOEX, MADATA[31: 0] - 20 - ns MOEX↑→ Data hold time tDH - OE MOEX, MADATA[31: 0] - 0 - ns MWEX Minimum pulse width tWEW MWEX - MCLK×n-3 - ns MWEX↑→Address output delay time tWEH - AX MWEX, MAD[24: 0] - 0 MCLK×m+9 ns MCSX↓→ MWEX↓delay time tCSL - WEL - MCLK×n-9 MCLK×n+9 ns MWEX↑→ MCSX↑delay time tWEH - CSH - 0 MCLK×m+9 ns MCSX↓→ MDQM↓delay time tCSL-WDQML MCSX, MDQM[3: 0] - MCLK×n-9 MCLK×n+9 ns tCSL-DX MCSX, MADATA[31: 0] - MCLK-9 MCLK+9 ns tWEH - DX MWEX, MADATA[31: 0] - 0 MCLK×m+9 ns MCSX↓→ Data output time MWEX↑→ Data hold time MWEX, MCSX[7: 0] Remarks Note: − When the external load capacitance CL = 30 pF (m = 0 to 15, n = 1 to 16) Document Number: 002-04988 Rev. *C Page 115 of 198 S6E2C3 Series tCYCLE MCLK tOEH-CSH MCSX[7: 0] MAD[24: 0] tCSL-AV tWEH-CSH tOEH-AX Address tWEH-AX tCSL-AV Address tCSL-OEL MOEX tOEW tCSL-WDQML tCSL-RDQML MDQM[1: 0] tCSL-WEL MWEX tWEW tDS-OE MADATA[15: 0] tDH-OE RD tWEH-DX WD Invalid tCSL-DX Document Number: 002-04988 Rev. *C Page 116 of 198 S6E2C3 Series Separate Bus Access Synchronous SRAM Mode (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol Pin Name Conditions tAV MCLK, MAD[24: 0] Address delay time tCSL MCSX delay time tCSH Max - 1 9 ns MCLK, MCSX[7: 0] - 1 9 ns - 1 9 ns MCLK, MOEX - 1 9 ns - 1 9 ns - 19 - ns - 0 - ns MCLK, MWEX - 1 9 ns - 1 9 ns MCLK, MDQM[3: 0] - 1 9 ns - 1 9 ns - MCLK + 1 MCLK + 18 ns - 1 18 ns tREH Data set up →MCLK↑ time MCLK↑→ Data hold time MCLK, MADATA[31: 0] MCLK, MADATA[31: 0] tDS tDH tWEL MWEX delay time tWEH tDQML MDQM[1: 0] delay time tDQMH MCLK↑→ Data output time MCLK↑→ Data hold time tODS tOD Unit Min tREL MOEX delay time Value MCLK, MADATA[31: 0] MCLK, MADATA[31: 0] Remarks Note: − When the external load capacitance CL = 30 pF tCYCLE MCLK tCSL tCSH MCSX[7: 0] tAV tAV Address MAD[24: 0] Address tREL tREH tDQML tDQMH MOEX tDQML tDQMH tWEL tWEH MDQM[3: 0] MWEX MADATA[31: 0] tDS tDH RD tOD WD Invalid tODS Document Number: 002-04988 Rev. *C Page 117 of 198 S6E2C3 Series Multiplexed Bus Access Asynchronous SRAM Mode (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol Multiplexed address delay time tALE-CHMADV Multiplexed address hold time tCHMADH Pin Name MALE, MAD[24: 0] Conditions Value Unit Min Max - 0 10 ns - MCLK × n+0 MCLK × n + 10 ns Remarks Note: − When the external load capacitance CL = 30 pF (m = 0 to 15, n = 1 to 16) MCLK MCSX[7: 0] MALE MAD [24: 0] MOEX MDQM [3: 0] MWEX MADATA[31: 0] Document Number: 002-04988 Rev. *C Page 118 of 198 S6E2C3 Series Multiplexed Bus Access Synchronous SRAM Mode (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter MALE delay time Symbol Pin Name Conditions tCHAL MCLK, MALE tCHAH MCLK↑→Multiplexed address delay time MCLK↑→Multiplexed data output time tCHMADV tCHMADX MCLK, MADATA[31: 0] Value Unit Min Max - 1 9 - 1 9 - 1 tOD ns - 1 tOD ns Remarks Note: − When the external load capacitance CL = 30 pF MCLK MCSX[7: 0] MALE MAD [24: 0] MOEX MDQM [3: 0] MWEX MADATA[31: 0] Document Number: 002-04988 Rev. *C Page 119 of 198 S6E2C3 Series NAND Flash Mode (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter MNREX Min pulse width Data set up →MNREX↑time Symbol Pin Name Conditions tNREW MNREX tDS – NRE MNREX, MADATA[31: 0] MNREX, MADATA[31: 0] MNALE, MNWEX MNALE, MNWEX MNCLE, MNWEX Value Unit Min Max - MCLK × n-3 - ns - 20 - ns - 0 - ns MCLK × m-9 MCLK × m-9 MCLK × m-9 MCLK × m+9 MCLK × m+9 MCLK × m+9 MNREX↑→ Data hold time MNALE↑→ MNWEX delay time MNALE↓→ MNWEX delay time MNCLE↑→ MNWEX delay time tCLEH - NWEL MNWEX↑→ MNCLE delay time tNWEH - CLEL MNCLE, MNWEX - 0 MCLK × m+9 ns tNWEW MNWEX - MCLK × n-3 - ns - -9 9 ns - 0 MCLK × m+9 ns MNWEX Min pulse width MNWEX↓→ Data output time MNWEX↑→ Data hold time tDH – NRE tALEH - NWEL tALEL - NWEL tNWEL – DV tNWEH – DX MNWEX, MADATA[31: 0] MNWEX, MADATA[31: 0] - Remarks ns ns ns Note: − When the external load capacitance CL = 30 pF (m = 0 to 15, n = 1 to 16) NAND Flash Read MCLK MNREX MADATA[31: 0] Document Number: 002-04988 Rev. *C Read Page 120 of 198 S6E2C3 Series NAND Flash Address Write MCLK MNALE MNCLE MNWEX MADATA[31: 0] Write NAND Flash Command Write MCLK MNALE MNCLE MNWEX MADATA[31: 0] Document Number: 002-04988 Rev. *C Write Page 121 of 198 S6E2C3 Series External Ready Input Timing (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter MCLK↑ MRDY input setup time Symbol Pin Name Conditions tRDYI MCLK, MRDY - Value Min Max 19 - Unit Remarks ns  When RDY is input ··· MCLK Over 2cycle Original MOEX MWEX tRDYI MRDY  When RDY is released MCLK ··· ··· 2 cycles Extended MOEX MWEX tRDYI 0.5×VCC MRDY Document Number: 002-04988 Rev. *C Page 122 of 198 S6E2C3 Series SDRAM Mode (VCC = 2.7 V to 3.6 V, VSS = 0 V) Parameter Symbol Pin Name Value Output frequency tCYCSD MSDCLK Address delay time tAOSD MSDCLK↑→ Data output delay time MSDCLK↑→ Data output Hi-Z time tDOSD tDOZSD MDQM[3: 0] delay time tWROSD MCSX delay time tMCSSD MRASX delay time tRASSD MCASX delay time tCASSD MSDWEX delay time tMWESD MSDCKE delay time tCKESD Data set up time tDSSD Data hold time tDHSD MSDCLK, MAD[15: 0] MSDCLK, MADATA[31: 0] MSDCLK, MADATA[31: 0] MSDCLK, MDQM[1: 0] MSDCLK, MCSX8 MSDCLK, MRASX MSDCLK, MCASX MSDCLK, MSDWEX MSDCLK, MSDCKE MSDCLK, MADATA[31: 0] MSDCLK, MADATA[31: 0] Unit Unit Min Max - - 50 MHz - 2 12 ns - 2 12 ns - 2 19.5 ns - 1 12 ns - 2 12 ns - 2 12 ns - 2 12 ns - 2 12 ns - 2 12 ns - 19 - ns - 0 - ns Remarks Note: − When the external load capacitance CL = 30 pF Document Number: 002-04988 Rev. *C Page 123 of 198 S6E2C3 Series tCYCSD SDRAM Access MSDCLK tAOSD MAD[24:0] MDQM[1:0] MCSX MRASX MCASX MSDWEX MSDCKE Address tWROSD tMCSSD tRASSD tCASSD tMWESD tCKESD tDSSD MADATA[15:0] tDOSD MADATA[15:0] Document Number: 002-04988 Rev. *C tDHSD RD tDOZSD WD Page 124 of 198 S6E2C3 Series 12.4.11 Base Timer Input Timing Timer Input Timing (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Input pulse width Symbol Pin Name Conditions tTIWH, tTIWL TIOAn/TIOBn (when using as ECK, TIN) - tTIWH Value Min Max 2tCYCP - Unit Remarks ns tTIWL ECK VIHS TIN VIHS VILS VILS Trigger Input Timing (VCC = 2.7V to 5.5V, VSS = 0V) Parameter Input pulse width Symbol Pin Name Conditions tTRGH, tTRGL TIOAn/TIOBn (when using as TGIN) - tTRGH TGIN VIHS Value Min Max 2tCYCP - Unit Remarks ns tTRGL VIHS VILS VILS Note: − tCYCP indicates the APB bus clock cycle time. For more information about the APB bus number to which the base timer is connected, see 8. Block Diagram in this data sheet. Document Number: 002-04988 Rev. *C Page 125 of 198 S6E2C3 Series 12.4.12 CSIO (SPI) Timing Synchronous Serial (SPI = 0, SCINV = 0) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol Pin Name - SCKx SCKx, SOTx SCKx, SINx SCKx, SINx SCKx SCKx SCKx, SOTx SCKx, SINx SCKx, SINx SCKx SCKx Baud rate Serial clock cycle time tSCYC SCK↓→SOT delay time tSLOVI SIN→SCK↑ setup time tIVSHI SCK↑→SIN hold time tSHIXI Serial clock L pulse width Serial clock H pulse width tSLSH tSHSL SCK↓→SOT delay time tSLOVE SIN→SCK↑ setup time tIVSHE SCK↑→SIN hold time tSHIXE SCK fall time SCK rise time tF tR Conditions Internal shift clock operation External shift clock operation VCC < 4.5 V VCC ≥ 4.5 V Unit Min Max Min Max - - 4tCYCP 8 - 4tCYCP 8 - Mbps ns -30 +30 -20 +20 ns 50 - 30 - ns 0 - 0 - ns 2tCYCP - 10 tCYCP + 10 - 2tCYCP - 10 tCYCP + 10 - ns ns - 50 - 30 ns 10 - 10 - ns 20 - 20 - ns - 5 5 - 5 5 ns ns Notes: The above characteristics apply to CLK synchronous mode. − − tCYCP indicates the APB bus clock cycle time. For more information about the APB bus number to which the multi-function serial is connected, see 8. Block Diagram in this data sheet. − These characteristics only guarantee the same relocate port number; for example, the combination of SCKx_0 and SOTx_1 is not guaranteed. − When the external load capacitance CL = 30 pF. Document Number: 002-04988 Rev. *C Page 126 of 198 S6E2C3 Series tSCYC VOH SCK VOL VOL tSLOVI VOH VOL SOT tIVSHI VIH VIL SIN tSHIXI VIH VIL MS bit = 0 tSLSH SCK VIH tF VIL tSHSL VIL SIN VIH tR tSLOVE SOT VIH VOH VOL tIVSHE VIH VIL tSHIXE VIH VIL MS bit = 1 Document Number: 002-04988 Rev. *C Page 127 of 198 S6E2C3 Series Synchronous Serial (SPI = 0, SCINV = 1) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Symbol Pin Name Conditions Baud rate Serial clock cycle time tSCYC - SCK↑→SOT delay time tSHOVI SIN→SCK↓ setup time tIVSLI SCK↓→SIN hold time tSLIXI Serial clock L pulse width tSLSH SCKx SCKx, SOTx SCKx, SINx SCKx, SINx SCKx Serial clock H pulse width tSHSL SCKx SCK↑→SOT delay time tSHOVE SIN→SCK↓ setup time tIVSLE SCK↓→SIN hold time tSLIXE Parameter SCK fall time SCK rise time tF tR SCKx, SOTx SCKx, SINx SCKx, SINx SCKx SCKx Internal shift clock operation External shift clock operation VCC < 4.5 V VCC ≥ 4.5 V Unit Min Max Min Max 4tCYCP 8 - 4tCYCP 8 - Mbps ns -30 +30 -20 +20 ns 50 - 30 - ns 0 - 0 - ns 2tCYCP - 10 - 2tCYCP - 10 - ns tCYCP + 10 - tCYCP + 10 - ns - 50 - 30 ns 10 - 10 - ns 20 - 20 - ns - 5 5 - 5 5 ns ns Notes: − The above characteristics apply to CLK synchronous mode. − tCYCP indicates the APB bus clock cycle time. For more information about the APB bus number to which the multi-function serial is connected, see 8. Block Diagram in this data sheet. − These characteristics only guarantee the same relocate port number; for example, the combination of SCKx_0 and SOTx_1 is not guaranteed. − When the external load capacitance CL = 30 pF. Document Number: 002-04988 Rev. *C Page 128 of 198 S6E2C3 Series tSCYC VOH SCK VOH VOL tSHOVI VOH VOL SOT tIVSLI VIH VIL SIN tSLIXI VIH VIL MS bit = 0 tSHSL SCK tSLSH VIH VIH VIL tR VIL tF tSHOVE SOT SIN VIL VOH VOL tIVSLE VIH VIL tSLIXE VIH VIL MS bit = 1 Document Number: 002-04988 Rev. *C Page 129 of 198 S6E2C3 Series Synchronous Serial (SPI = 1, SCINV = 0) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Symbol Pin Name Conditions Baud rate Serial clock cycle time tSCYC - SCK↑→SOT delay time tSHOVI SIN→SCK↓ setup time tIVSLI SCK↓→SIN hold time tSLIXI SOT→SCK↓ delay time tSOVLI Serial clock L pulse width Serial clock H pulse width tSLSH tSHSL SCK↑→SOT delay time tSHOVE SCKx SCKx, SOTx SCKx, SINx SCKx, SINx SCKx, SOTx SCKx SCKx SCKx, SOTx SCKx, SINx SCKx, SINx SCKx SCKx Parameter SIN→SCK↓ setup time tIVSLE SCK↓→SIN hold time tSLIXE SCK fall time SCK rise time tF tR Internal shift clock operation External shift clock operation VCC < 4.5 V VCC ≥ 4.5 V Unit Min Max Min Max 4tCYCP 8 - 4tCYCP 8 - Mbps ns -30 +30 -20 +20 ns 50 - 30 - ns 0 - 0 - ns 2tCYCP - 30 - 2tCYCP - 30 - ns 2tCYCP - 10 tCYCP + 10 - 2tCYCP - 10 tCYCP + 10 - ns ns - 50 - 30 ns 10 - 10 - ns 20 - 20 - ns - 5 5 - 5 5 ns ns Notes: − The above characteristics apply to CLK synchronous mode. − tCYCP indicates the APB bus clock cycle time. For more information about the APB bus number to which the multi-function serial is connected, see 8. Block Diagram in this data sheet. − These characteristics only guarantee the same relocate port number; for example, the combination of SCKx_0 and SOTx_1 is not guaranteed. − When the external load capacitance CL = 30 pF. Document Number: 002-04988 Rev. *C Page 130 of 198 S6E2C3 Series tSCYC VOH SCK SOT VOL VOH VOL VOH VOL tIVSLI tSLIXI VIH VIL SIN VOL tSHOVI tSOVLI VIH VIL MS bit = 0 tSLSH SCK VIH VIH VIL tF * SOT VIL tSHSL tR VIH tSHOVE VOH VOL VOH VOL tIVSLE SIN tSLIXE VIH VIL VIH VIL MS bit = 1 *: Changes when writing to TDR register Document Number: 002-04988 Rev. *C Page 131 of 198 S6E2C3 Series Synchronous Serial (SPI = 1, SCINV = 1) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Symbol Pin Name Conditions Baud rate Serial clock cycle time tSCYC - SCK↓→SOT delay time tSLOVI SIN→SCK↑ setup time tIVSHI SCK↑→SIN hold time tSHIXI SOT→SCK↑ delay time tSOVHI Serial clock L pulse width Serial clock H pulse width tSLSH tSHSL SCK↓→SOT delay time tSLOVE SCKx SCKx, SOTx SCKx, SINx SCKx, SINx SCKx, SOTx SCKx SCKx SCKx, SOTx SCKx, SINx SCKx, SINx SCKx SCKx Parameter SIN→SCK↑ setup time tIVSHE SCK↑→SIN hold time tSHIXE SCK fall time SCK rise time tF tR Internal shift clock operation External shift clock operation VCC < 4.5 V VCC ≥ 4.5 V Unit Min Max Min Max 4tCYCP 8 - 4tCYCP 8 - Mbps ns -30 +30 -20 +20 ns 50 - 30 - ns 0 - 0 - ns 2tCYCP - 30 - 2tCYCP - 30 - ns 2tCYCP - 10 tCYCP + 10 - 2tCYCP - 10 tCYCP + 10 - ns ns - 50 - 30 ns 10 - 10 - ns 20 - 20 - ns - 5 5 - 5 5 ns ns Notes: − The above characteristics apply to CLK synchronous mode. − tCYCP indicates the APB bus clock cycle time. For more information about the APB bus number to which the multi-function serial is connected, see 8. Block Diagram in this data sheet. − These characteristics only guarantee the same relocate port number; for example, the combination of SCKx_0 and SOTx_1 is not guaranteed. − When the external load capacitance CL = 30 pF. Document Number: 002-04988 Rev. *C Page 132 of 198 S6E2C3 Series tSCYC VOH SCK tSOVHI SOT tSLOVI VOH VOL VOH VOL tSHIXI tIVSHI VIH VIL SIN VOH VOL VIH VIL MS bit = 0 tSHSL tR SCK VIL VIH tSLSH VIH VIL tF VIL VIH tSLOVE SOT VOH VOL VOH VOL tIVSHE SIN tSHIXE VIH VIL VIH VIL MS bit = 1 Document Number: 002-04988 Rev. *C Page 133 of 198 S6E2C3 Series When Using Synchronous Serial Chip Select (SCINV = 0, CSLVL = 1) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol SCS↓→SCK↓ setup time tCSSI SCK↑→SCS↑ hold time tCSHI SCS deselect time tCSDI SCS↓→SCK↓ setup time tCSSE SCK↑→SCS↑ hold time tCSHE SCS deselect time tCSDE SCS↓→SOT delay time SCS↑→SOT delay time tDSE Conditions Internal shift clock operation External shift clock operation tDEE VCC < 4.5 V VCC ≥ 4.5 V Unit Min Max Min Max (*1) - 50 (*1) + 0 (*1) - 50 (*1) + 0 ns (*2) + 0 (*3) - 50 + 5tCYCP 3tCYCP + 30 (*2) + 50 (*3) + 50 + 5tCYCP - (*2) + 0 (*3) – 50 + 5tCYCP 3tCYCP + 30 (*2) + 50 (*3) + 50 + 5tCYCP - ns ns ns 0 - 0 - ns 3tCYCP + 30 - 3tCYCP + 30 - ns - 40 - 40 ns 0 - 0 - ns (*1): CSSU bit value×serial chip select timing operating clock cycle [ns] (*2): CSHD bit value×serial chip select timing operating clock cycle [ns] (*3): CSDS bit value×serial chip select timing operating clock cycle [ns] Notes: − tCYCP indicates the APB bus clock cycle time. For more information about the APB bus number to which the multifunction serial is connected, see 8. Block Diagram in this data sheet. − For more information about CSSU, CSHD, CSDS, and the serial chip select timing operating clock, see FM4 Family Peripheral Manual Main Part (002-04856). − When the external load capacitance CL = 30 pF. Document Number: 002-04988 Rev. *C Page 134 of 198 S6E2C3 Series SCS output tCSDI tCSHI tCSSI SCK output SOT (SPI=0) SOT (SPI=1) MS bit = 0 SCS input tCSDE tCSSE tCSHE SCK input tDEE SOT (SPI=0) tDSE SOT (SPI=1) MS bit = 1 Document Number: 002-04988 Rev. *C Page 135 of 198 S6E2C3 Series When Using Synchronous Serial Chip Select (SCINV = 1, CSLVL = 1) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol SCS↓→SCK↓ setup time tCSSI SCK↑→SCS↑ hold time tCSHI SCS deselect time tCSDI SCS↓→SCK↓ setup time tCSSE SCK↑→SCS↑ hold time tCSHE SCS deselect time tCSDE SCS↓→SOT delay time SCS↑→SOT delay time tDSE Conditions Internal shift clock operation External shift clock operation tDEE VCC < 4.5 V VCC ≥ 4.5 V Unit Min Max Min Max (*1) - 50 (*1) + 0 (*1) - 50 (*1) + 0 ns (*2) + 0 (*3) - 50 + 5tCYCP 3tCYCP + 30 (*2) + 50 (*3) + 50 + 5tCYCP - (*2) + 0 (*3) – 50 + 5tCYCP 3tCYCP + 30 (*2) + 50 (*3) + 50 + 5tCYCP - ns ns ns 0 - 0 - ns 3tCYCP + 30 - 3tCYCP + 30 - ns - 40 - 40 ns 0 - 0 - ns (*1): CSSU bit value×serial chip select timing operating clock cycle [ns] (*2): CSHD bit value×serial chip select timing operating clock cycle [ns] (*3): CSDS bit value×serial chip select timing operating clock cycle [ns] Notes: − tCYCP indicates the APB bus clock cycle time. For more information about the APB bus number to which the multifunction serial is connected, see 8. Block Diagram in this data sheet. − For more information about CSSU, CSHD, CSDS, and the serial chip select timing operating clock, see FM4 Family Peripheral Manual Main Part (002-04856). − When the external load capacitance CL = 30 pF. Document Number: 002-04988 Rev. *C Page 136 of 198 S6E2C3 Series SCS output tCSDI tCSHI tCSSI SCK output SOT (SPI=0) SOT (SPI=1) MS bit = 0 SCS input tCSDE tCSHE tCSSE SCK input tDEE SOT (SPI=0) tDSE SOT (SPI=1) MS bit = 1 Document Number: 002-04988 Rev. *C Page 137 of 198 S6E2C3 Series When Using Synchronous Serial Chip Select (SCINV = 0, CSLVL = 0) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol SCS↑→SCK↓ setup time tCSSI SCK↑→SCS↓ hold time tCSHI SCS deselect time tCSDI Conditions Internal shift clock operation VCC < 4.5 V VCC ≥ 4.5 V Unit Min Max Min Max (*1) - 50 (*1) + 0 (*1) - 50 (*1) + 0 ns (*2) + 50 (*3) + 50 + 5tCYCP - (*2) + 0 (*3) – 50 + 5tCYCP 3tCYCP + 30 (*2) + 50 (*3) + 50 + 5tCYCP - ns SCS↑→SCK↓ setup time tCSSE (*2) + 0 (*3) – 50 + 5tCYCP 3tCYCP + 30 SCK↑→SCS↓ hold time tCSHE 0 - 0 - ns SCS deselect time tCSDE 3tCYCP + 30 - 3tCYCP + 30 - ns SCS↑→SOT delay time tDSE - 40 - 40 ns SCS↓→SOT delay time tDEE 0 - 0 - ns External shift clock operation ns ns (*1): CSSU bit value×serial chip select timing operating clock cycle [ns] (*2): CSHD bit value×serial chip select timing operating clock cycle [ns] (*3): CSDS bit value×serial chip select timing operating clock cycle [ns] Notes: − tCYCP indicates the APB bus clock cycle time. For more information about the APB bus number to which the multifunction serial is connected, see 8. Block Diagram in this data sheet. − For more information about CSSU, CSHD, CSDS, and the serial chip select timing operating clock, see FM4 Family Peripheral Manual Main Part (002-04856). − When the external load capacitance CL = 30 pF. Document Number: 002-04988 Rev. *C Page 138 of 198 S6E2C3 Series tCSDI SCS output tCSHI tCSSI SCK output SOT (SPI=0) SOT (SPI=1) MS bit = 0 tCSDE SCS input tCSHE tCSSE SCK input tDEE SOT (SPI=0) tDSE SOT (SPI=1) MS bit = 1 Document Number: 002-04988 Rev. *C Page 139 of 198 S6E2C3 Series When Using Synchronous Serial Chip Select (SCINV = 1, CSLVL = 0) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol SCK↓→SCS↓hold time tCSSI tCSHI SCS deselect time tCSDI SCS↑→SCK↑setup time Conditions Internal shift clock operation VCC < 4.5 V SCK↓→SCS↓hold time Units Max Min Max (*1) - 50 (*1) + 0 (*1) - 50 (*1) + 0 ns (*2) + 0 (*3) – 50 + 5tCYCP 3tCYCP + 30 (*2) + 50 (*3) + 50 + 5tCYCP - (*2) + 0 (*3) – 50 + 5tCYCP 3tCYCP + 30 (*2) + 50 (*3) + 50 + 5tCYCP - ns - 0 - ns - 3tCYCP + 30 - ns 40 - 40 ns - 0 - ns tCSSE 0 tCSHE External SCS deselect time shift clock 3tCYCP + 30 tCSDE operation SCS↑→SOT delay time tDSE SCS↓→SOT delay time 0 tDEE (*1): CSSU bit value×serial chip select timing operating clock cycle [ns] (*2): CSHD bit value×serial chip select timing operating clock cycle [ns] (*3): CSDS bit value×serial chip select timing operating clock cycle [ns] SCS↑→SCK↑setup time VCC ≥ 4.5 V Min ns ns Notes: − tCYCP indicates the APB bus clock cycle time. For more information about the APB bus number to which the multifunction serial is connected, see 8. Block Diagram in this data sheet. − For more information about CSSU, CSHD, CSDS, and the serial chip select timing operating clock, see FM4 Family Peripheral Manual Main Part (002-04856). − When the external load capacitance CL = 30 pF. Document Number: 002-04988 Rev. *C Page 140 of 198 S6E2C3 Series tCSDI SCS output tCSHI tCSSI SCK output SOT (SPI=0) SOT (SPI=1) MS bit = 0 tCSDE SCS input tCSHE tCSSE SCK input tDEE SOT (SPI=0) tDSE SOT (SPI=1) MS bit = 1 Document Number: 002-04988 Rev. *C Page 141 of 198 S6E2C3 Series High-Speed Synchronous Serial (SPI = 0, SCINV = 0) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Symbol Pin Name Serial clock cycle time tSCYC SCK↓→SOT delay time tSLOVI SCKx SCKx, SOTx SIN→SCK↑ setup time tIVSHI SCK↑→SIN hold time tSHIXI Serial clock L pulse width tSLSH SCKx, SINx SCKx Serial clock H pulse width tSHSL SCKx SCK↓→SOT delay time tSLOVE SIN→SCK↑ setup time tIVSHE SCK↑→SIN hold time tSHIXE Parameter SCK fall time SCK rise time tF tR SCKx, SINx SCKx, SOTx SCKx, SINx SCKx, SINx SCKx SCKx Conditions Internal shift clock operation External shift clock operation VCC < 4.5 V VCC ≥ 4.5 V Unit Min Max Min Max 4tCYCP - 4tCYCP - ns -10 +10 -10 +10 ns - 12.5 - ns 5 - 5 - ns 2tCYCP - 5 tCYCP + 10 - 2tCYCP - 5 tCYCP + 10 - ns - ns - 15 - 15 ns 5 - 5 - ns 5 - 5 - ns - 5 5 - 5 5 ns ns 14 12.5* - Notes: − The above characteristics apply to CLK synchronous mode. − tCYCP indicates the APB bus clock cycle time. For more information about the APB bus number to which the multi-function serial is connected, see 8. Block Diagram in this data sheet. − These characteristics only guarantee the following pins: No chip select: SIN4_0, SOT4_0, SCK4_0 Chip select: SIN6_0, SOT6_0, SCK6_0, SCS60_0, SCS61_0, SCS62_0, SCS63_0 − When the external load capacitance CL = 30 pF. (For *, when CL = 10 pF) Document Number: 002-04988 Rev. *C Page 142 of 198 S6E2C3 Series tSCYC VOH SCK VOL VOL tSLOVI VOH VOL SOT tIVSHI VIH VIL SIN tSHIXI VIH VIL MS bit = 0 tSLSH SCK VIH tF VIL tSHSL VIL SIN VIH tR tSLOVE SOT VIH VOH VOL tIVSHE VIH VIL tSHIXE VIH VIL MS bit = 1 Document Number: 002-04988 Rev. *C Page 143 of 198 S6E2C3 Series High-Speed Synchronous Serial (SPI = 0, SCINV = 1) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol Serial clock cycle time tSCYC SCK↑→SOT delay time tSHOVI Pin Name SCKx SCKx, SOTx SCKx, SINx SIN→SCK↓ setup time tIVSLI SCK↓→SIN hold time tSLIXI Serial clock L pulse width tSLSH SCKx, SINx SCKx Serial clock H pulse width tSHSL SCKx SCK↑→SOT delay time tSHOVE SIN→SCK↓ setup time tIVSLE SCK↓→SIN hold time tSLIXE SCK fall time SCK rise time tF tR SCKx, SOTx SCKx, SINx SCKx, SINx SCKx SCKx Conditions VCC < 4.5 V Min Max 4tCYCP -10 Internal shift clock operation External shift clock operation VCC ≥ 4.5 V Min Max 4tCYCP - Unit ns +10 -10 +10 ns - 12.5 - ns 5 - 5 - ns 2tCYCP - 5 tCYCP + 10 - 2tCYCP - 5 tCYCP + 10 - ns - ns - 15 - 15 ns 5 - 5 - ns 5 - 5 - ns - 5 5 - 5 5 ns ns 14 12.5* - Notes: − The above characteristics apply to CLK synchronous mode. − tCYCP indicates the APB bus clock cycle time. For more information about the APB bus number to which the multi-function serial is connected, see 8. Block Diagram in this data sheet. − These characteristics only guarantee the following pins: No chip select: SIN4_0, SOT4_0, SCK4_0 Chip select: SIN6_0, SOT6_0, SCK6_0, SCS60_0, SCS61_0, SCS62_0, SCS63_0 − When the external load capacitance CL = 30 pF. (For *, when CL = 10 pF) Document Number: 002-04988 Rev. *C Page 144 of 198 S6E2C3 Series tSCYC VOH SCK VOH VOL tSHOVI VOH VOL SOT tIVSLI VIH VIL SIN tSLIXI VIH VIL MS bit = 0 tSHSL SCK tSLSH VIH VIH VIL tR VIL tF tSHOVE SOT SIN VIL VOH VOL tIVSLE VIH VIL tSLIXE VIH VIL MS bit = 1 Document Number: 002-04988 Rev. *C Page 145 of 198 S6E2C3 Series High-Speed Synchronous Serial (SPI = 1, SCINV = 0) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Symbol Pin Name Serial clock cycle time tSCYC SCK↑→SOT delay time tSHOVI SCKx SCKx, SOTx SIN→SCK↓ setup time tIVSLI SCK↓→SIN hold time tSLIXI SOT→SCK↓ delay time tSOVLI Serial clock L pulse width Serial clock H pulse width tSLSH tSHSL SCK↑→SOT delay time tSHOVE Parameter SIN→SCK↓ setup time tIVSLE SCK↓→SIN hold time tSLIXE SCK fall time SCK rise time tF tR SCKx, SINx SCKx, SINx SCKx, SOTx SCKx SCKx SCKx, SOTx SCKx, SINx SCKx, SINx SCKx SCKx VCC < 4.5 V Conditions Internal shift clock operation VCC ≥ 4.5 V Unit Min Max Min Max 4tCYCP - 4tCYCP - ns -10 +10 -10 +10 ns - 12.5 - ns 5 - 5 - ns 2tCYCP - 10 - 2tCYCP - 10 - ns 2tCYCP - 5 tCYCP + 10 - 2tCYCP - 5 tCYCP + 10 - ns ns - 15 - 15 ns 5 - 5 - ns 5 - 5 - ns - 5 5 - 5 5 ns ns 14 12.5* External shift clock operation Notes: − The above characteristics apply to CLK synchronous mode. − tCYCP indicates the APB bus clock cycle time. For more information about the APB bus number to which the multi-function serial is connected, see 8. Block Diagram in this data sheet. − These characteristics only guarantee the following pins: No chip select: SIN4_0, SOT4_0, SCK4_0 Chip select: SIN6_0, SOT6_0, SCK6_0, SCS60_0, SCS61_0, SCS62_0, SCS63_0 − When the external load capacitance CL = 30 pF. (for *, when CL = 10 pF) Document Number: 002-04988 Rev. *C Page 146 of 198 S6E2C3 Series tSCYC VOH SCK SOT VOL VOH VOL VOH VOL tIVSLI tSLIXI VIH VIL SIN VOL tSHOVI tSOVLI VIH VIL MS bit = 0 tSLSH SCK VIH tR VIH tSHOVE VOH VOL VOH VOL tIVSLE SIN VIH VIL tF * SOT VIL tSHSL tSLIXE VIH VIL VIH VIL MS bit = 1 *: Changes when writing to TDR register Document Number: 002-04988 Rev. *C Page 147 of 198 S6E2C3 Series High-Speed Synchronous Serial (SPI = 1, SCINV = 1) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Symbol Pin Name Serial clock cycle time tSCYC SCK↓→SOT delay time tSLOVI SCKx SCKx, SOTx SIN→SCK↑ setup time tIVSHI SCK↑→SIN hold time tSHIXI SOT→SCK↑ delay time tSOVHI Serial clock L pulse width Serial clock H pulse width tSLSH tSHSL SCK↓→SOT delay time tSLOVE Parameter SIN→SCK↑ setup time tIVSHE SCK↑→SIN hold time tSHIXE SCK fall time SCK rise time tF tR SCKx, SINx SCKx, SINx SCKx, SOTx SCKx SCKx SCKx, SOTx SCKx, SINx SCKx, SINx SCKx SCKx VCC < 4.5 V Conditions Internal shift clock operation VCC ≥ 4.5 V Unit Min Max Min Max 4tCYCP - 4tCYCP - ns -10 +10 -10 +10 ns - 12.5 - ns 5 - 5 - ns 2tCYCP - 10 - 2tCYCP - 10 - ns 2tCYCP - 5 tCYCP + 10 - 2tCYCP - 5 tCYCP + 10 - ns ns - 15 - 15 ns 5 - 5 - ns 5 - 5 - ns - 5 5 - 5 5 ns ns 14 12.5* External shift clock operation Notes: − The above characteristics apply to CLK synchronous mode. − tCYCP indicates the APB bus clock cycle time. For more information about the APB bus number to which the multi-function serial is connected, see 8. Block Diagram in this data sheet. − These characteristics only guarantee the following pins: No chip select: SIN4_0, SOT4_0, SCK4_0 Chip select: SIN6_0, SOT6_0, SCK6_0, SCS60_0, SCS61_0, SCS62_0, SCS63_0 − When the external load capacitance CL = 30 pF. (for *, when CL = 10 pF) Document Number: 002-04988 Rev. *C Page 148 of 198 S6E2C3 Series tSCYC VOH SCK tSOVHI SOT tSLOVI VOH VOL VOH VOL tSHIXI tIVSHI VIH VIL SIN VOH VOL VIH VIL MS bit = 0 tSHSL tR SCK VIL VIH tSLSH VIH VIL tF VIL VIH tSLOVE SOT VOH VOL VOH VOL tIVSHE SIN tSHIXE VIH VIL VIH VIL MS bit = 1 Document Number: 002-04988 Rev. *C Page 149 of 198 S6E2C3 Series When Using High-Speed Synchronous Serial Chip Select (SCINV = 0, CSLVL = 1) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol SCS↓→SCK↓ setup time tCSSI SCK↑→SCS↑ hold time tCSHI SCS deselect time tCSDI SCS↓→SCK↓ setup time tCSSE SCK↑→SCS↑ hold time tCSHE SCS deselect time tCSDE SCS↓→SOT delay time tDSE SCS↑→SOT delay time tDEE Conditions Internal shift clock operation External shift clock operation VCC < 4.5 V VCC ≥ 4.5 V Unit Min Max Min Max (*1) - 20 (*1) + 0 (*1) - 20 (*1) + 0 ns (*2) + 0 (*3) – 20 + 5tCYCP 3tCYCP + 15 (*2) + 20 (*3) + 20 + 5tCYCP - (*2) + 0 (*3) – 20 + 5tCYCP 3tCYCP + 15 (*2) + 20 (*3) + 20 + 5tCYCP - ns ns ns 0 - 0 - ns 3tCYCP + 15 - 3tCYCP + 15 - ns - 25 - 25 ns 0 - 0 - ns (*1): CSSU bit value×serial chip select timing operating clock cycle [ns] (*2): CSHD bit value×serial chip select timing operating clock cycle [ns] (*3): CSDS bit value×serial chip select timing operating clock cycle [ns] Notes: − tCYCP indicates the APB bus clock cycle time. For more information about the APB bus number to which the multifunction serial is connected, see 8. Block Diagram in this data sheet. − For more information about CSSU, CSHD, CSDS, and the serial chip select timing operating clock, see FM4 Family Peripheral Manual Main Part (002-04856). − When the external load capacitance CL = 30 pF. Document Number: 002-04988 Rev. *C Page 150 of 198 S6E2C3 Series SCS output tCSDI tCSHI tCSSI SCK output SOT (SPI=0) SOT (SPI=1) MS bit = 0 SCS input tCSDE tCSSE tCSHE SCK input tDEE SOT (SPI=0) tDSE SOT (SPI=1) MS bit = 1 Document Number: 002-04988 Rev. *C Page 151 of 198 S6E2C3 Series When Using High-Speed Synchronous Serial Chip Select (SCINV = 1, CSLVL = 1) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol SCS↓→SCK↓ setup time tCSSI SCK↑→SCS↑ hold time tCSHI SCS deselect time tCSDI SCS↓→SCK↑ setup time tCSSE SCK↑→SCS↑ hold time tCSHE SCS deselect time tCSDE SCS↓→SOT delay time tDSE SCS↑→SOT delay time tDEE Conditions Internal shift clock operation External shift clock operation VCC < 4.5 V VCC≥ 4.5 V Unit Min Min Min Max (*1) - 20 (*1) + 0 (*1) - 20 (*1) + 0 ns (*2) + 0 (*3) - 20 + 5tCYCP 3tCYCP + 15 (*2) + 20 (*3) + 20 + 5tCYCP - (*2) + 0 (*3) - 20 + 5tCYCP 3tCYCP + 15 (*2) + 20 (*3) + 20 + 5tCYCP - ns ns ns 0 - 0 - ns 3tCYCP + 15 - 3tCYCP + 15 - ns - 25 - 25 ns 0 - 0 - ns (*1): CSSU bit value×serial chip select timing operating clock cycle [ns] (*2): CSHD bit value×serial chip select timing operating clock cycle [ns] (*3): CSDS bit value×serial chip select timing operating clock cycle [ns] Notes: − tCYCP indicates the APB bus clock cycle time. For more information about the APB bus number to which the multifunction serial is connected, see 8. Block Diagram in this data sheet. − For more information about CSSU, CSHD, CSDS, and the serial chip select timing operating clock, see FM4 Family Peripheral Manual Main Part (002-04856). − When the external load capacitance CL = 30 pF. Document Number: 002-04988 Rev. *C Page 152 of 198 S6E2C3 Series SCS output tCSDI tCSHI tCSSI SCK output SOT (SPI=0) SOT (SPI=1) MS bit = 0 SCS intpu tCSDE tCSHE tCSSE SCK input tDEE SOT (SPI=0) tDSE SOT (SPI=1) MS bit = 1 Document Number: 002-04988 Rev. *C Page 153 of 198 S6E2C3 Series When Using High-Speed Synchronous Serial Chip Select (SCINV = 0, CSLVL = 0) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol SCS↑→SCK↓ setup time tCSSI SCK↑→SCS↓ hold time tCSHI SCS deselect time tCSDI Conditions Internal shift clock operation VCC < 4.5 V VCC ≥ 4.5 V Unit Min Max Min Max (*1)-20 (*1)+0 (*1)-20 (*1)+0 ns ( *2)+20 (*3)+20 +5tCYCP - ( *2)+0 (*3)-20 +5tCYCP 3tCYCP+15 ( *2)+20 (*3)+20 +5tCYCP - ns SCS↑→SCK↓ setup time tCSSE ( *2)+0 (*3)-20 +5tCYCP 3tCYCP+15 SCK↑→SCS↓ hold time tCSHE 0 - 0 - ns SCS deselect time tCSDE 3tCYCP+15 - 3tCYCP+15 - ns SCS↑→SOT delay time tDSE - 25 - 25 ns SCS↓→SOT delay time tDEE 0 - 0 - ns External shift clock operation ns ns (*1): CSSU bit value×serial chip select timing operating clock cycle [ns] (*2): CSHD bit value×serial chip select timing operating clock cycle [ns] (*3): CSDS bit value×serial chip select timing operating clock cycle [ns] Notes: − tCYCP indicates the APB bus clock cycle time. For more information about the APB bus number to which the multifunction serial is connected, see 8. Block Diagram in this data sheet. − For more information about CSSU, CSHD, CSDS, and the serial chip select timing operating clock, see FM4 Family Peripheral Manual Main Part (002-04856). − When the external load capacitance CL = 30 pF. Document Number: 002-04988 Rev. *C Page 154 of 198 S6E2C3 Series tCSDI SCS output tCSHI tCSSI SCK output SOT (SPI=0) SOT (SPI=1) MS bit = 0 tCSDE SCS input tCSHE tCSSE SCK input tDEE SOT (SPI=0) tDSE SOT (SPI=1) MS bit = 1 Document Number: 002-04988 Rev. *C Page 155 of 198 S6E2C3 Series When Using High-Speed Synchronous Serial Chip Select (SCINV = 1, CSLVL = 0) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol SCS↓→SCK↓ setup time tCSSI SCK↑→SCS↓ hold time tCSHI SCS deselect time tCSDI Conditions Internal shift clock operation VCC < 4.5 V VCC ≥ 4.5 V Unit Min Max Min Max (*1)-20 (*1)+0 (*1)-20 (*1)+0 ns ( *2)+20 (*3)+20 +5tCYCP - ( *2)+0 (*3)-20 +5tCYCP 3tCYCP+15 ( *2)+20 (*3)+20 +5tCYCP - ns SCS↑→SCK↑ setup time tCSSE ( *2)+0 (*3)-20 +5tCYCP 3tCYCP+15 SCK↓→SCS↓ hold time tCSHE 0 - 0 - ns SCS deselect time tCSDE 3tCYCP+15 - 3tCYCP+15 - ns SCS↑→SOT delay time tDSE - 40 - 40 ns SCS↓→SOT delay time tDEE 0 - 0 - ns External shift clock operation ns ns (*1): CSSU bit value×serial chip select timing operating clock cycle [ns] (*2): CSHD bit value×serial chip select timing operating clock cycle [ns] (*3): CSDS bit value×serial chip select timing operating clock cycle [ns] Notes: − tCYCP indicates the APB bus clock cycle time. For more information about the APB bus number to which the multifunction serial is connected, see 8. Block Diagram in this data sheet. − For more information about CSSU, CSHD, CSDS, and the serial chip select timing operating clock, see FM4 Family Peripheral Manual Main Part (002-04856). − When the external load capacitance CL = 30 pF. Document Number: 002-04988 Rev. *C Page 156 of 198 S6E2C3 Series tCSDI SCS output tCSHI tCSSI SCK output SOT (SPI=0) SOT (SPI=1) MS bit = 0 tCSDE SCS input tCSHE tCSSE SCK input tDEE SOT (SPI=0) tDSE SOT (SPI=1) MS bit = 1 Document Number: 002-04988 Rev. *C Page 157 of 198 S6E2C3 Series External clock (EXT = 1): When in Asynchronous Mode Only (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol Serial clock L pulse width tSLSH Serial clock H pulse width tSHSL SCK fall time tF SCK rise time tR CL = 30 pF tR SCK VIL Document Number: 002-04988 Rev. *C Value Condition Max tCYCP + 10 - ns tCYCP + 10 - ns - 5 ns - 5 ns tSHSL VIH Unit Min tF tSLSH VIH VIL Remarks VIL VIH Page 158 of 198 S6E2C3 Series 12.4.13 External Input Timing (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol Pin Name Conditions Value Min Max Unit A/D converter trigger input ADTGx FRCKx Input pulse width ICxx DTTIxX tINH, tINL - 2tCYCP*1 - ns - 2tCYCP*1 2tCYCP + 100*1 - ns - ns 500*2 - ns 500*3 - ns INT00 to INT31, NMIX - WKUPx - Remarks Free-run timer input clock Input capture Waveform generator External interrupt, NMI Deep standby wake up 1: tCYCP indicates the APB bus clock cycle time except stop when in Stop mode, in Timer mode. For more information about the APB bus number to which the A/D converter, multi-function timer, and external interrupt are connected, see 8. Block Diagram in this data sheet. 2: When in Stop mode, in Timer mode 3: When in Deep Standby RTC mode, in Deep Standby Stop mode Document Number: 002-04988 Rev. *C Page 159 of 198 S6E2C3 Series 12.4.14 Quadrature Position/Revolution Counter Timing (VCC = AVCC = 2.7 V to 5.5 V, VSS = AVSS = 0 V, TA = -40 °C to +105 °C) Parameter Symbol Conditions AIN pin H width AIN pin L width BIN pin H width BIN pin L width BIN rise time from AIN pin H level AIN fall time from BIN pin H level BIN fall time from AIN pin L level AIN rise time from BIN pin L level AIN rise time from BIN pin H level BIN fall time from AIN pin H level AIN fall time from BIN pin L level BIN rise time from AIN pin L level ZIN pin H width ZIN pin L width AIN/BIN rise and fall time from determined ZIN level Determined ZIN level from AIN/BIN rise and fall time tAHL tALL tBHL tBLL tZHL tZLL PC_Mode2 or PC_Mode3 PC_Mode2 or PC_Mode3 PC_Mode2 or PC_Mode3 PC_Mode2 or PC_Mode3 PC_Mode2 or PC_Mode3 PC_Mode2 or PC_Mode3 PC_Mode2 or PC_Mode3 PC_Mode2 or PC_Mode3 QCR: CGSC = 0 QCR: CGSC = 0 tZABE QCR: CGSC = 1 tABEZ QCR: CGSC = 1 tAUBU tBUAD tADBD tBDAU tBUAU tAUBD tBDAD tADBU Min Value Max 2tCYCP* - Unit ns *: tCYCP indicates the APB bus clock cycle time except when in Stop mode, in Timer mode. For more information about the APB bus number to which the quadrature position/revolution counter is connected, see "8. Block Diagram" in this data sheet. tALL tAHL AIN tAUBU tADBD tBUAD tBDAU BIN tBHL Document Number: 002-04988 Rev. *C tBLL Page 160 of 198 S6E2C3 Series tBLL tBHL BIN tBUAU tBDAD tAUBD tADBU AIN tAHL tALL ZIN Document Number: 002-04988 Rev. *C Page 161 of 198 S6E2C3 Series ZIN AIN/BIN Document Number: 002-04988 Rev. *C Page 162 of 198 S6E2C3 Series 12.4.15 I2C Timing Standard-mode, Fast-mode (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter SCL clock frequency (Repeated) START condition hold time SDA ↓ → SCL ↓ SCL clock L width SCL clock H width (Repeated) START condition setup time SCL ↑ → SDA ↓ Data hold time SCL ↓ → SDA ↓ ↑ Data setup time SDA ↓ ↑ → SCL ↑ Stop condition setup time SCL ↑ → SDA ↑ Bus free time between "Stop condition" and "START condition" Noise filter Symbol Conditions Standard-mode Fast-mode Unit Min Max Min Max fSCL 0 100 0 400 kHz tHDSTA 4.0 - 0.6 - μs tLOW tHIGH 4.7 4.0 - 1.3 0.6 - μs μs 4.7 - 0.6 - μs 0 3.45*2 0 0.9*3 μs tSUDAT 250 - 100 - ns tSUSTO 4.0 - 0.6 - μs tBUF 4.7 - 1.3 - μs 2 tCYCP*4 - 2 tCYCP*4 - ns 4 tCYCP*4 - 4 tCYCP*4 - ns *4 - 6 tCYCP *4 - ns 8 tCYCP*4 - 8 tCYCP*4 - ns tSUSTA tHDDAT tSP CL = 30 pF, R = (Vp/IOL)*1 2 MHz ≤ tCYCP＜40 MHz 40 MHz ≤ tCYCP ＜60 MHz 60 MHz ≤ tCYCP ＜80 MHz 80 MHz ≤ tCYCP ≤100 MHz Remarks *5 6 tCYCP *1: R and CL represent the pull-up resistance and load capacitance of the SCL and SDA lines, respectively. Vp indicates the power supply voltage of the pull-up resistance and IOL indicates VOL guaranteed current. *2: The maximum tHDDT must not extend beyond the low period (tLOW) of the device’s SCL signal. *3: Fast-mode I2C bus device can be used on a Standard-mode I2C bus system as long as the device satisfies the requirement of "tSUDAT ≥ 250 ns.” *4: tCYCP is the APB bus clock cycle time. For more information about the APB bus number to which the I2C is connected, see "8.Block Diagram" in this data sheet. When using Standard-mode, the peripheral bus clock must be set more than 2 MHz. When using Fast-mode, the peripheral bus clock must be set more than 8 MHz. *5: The noise filter time can be changed by register settings. Change the number of the noise filter steps according to the APB bus clock frequency. Document Number: 002-04988 Rev. *C Page 163 of 198 S6E2C3 Series Fast Mode Plus (Fm+) (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter SCL clock frequency (Repeated) START condition hold time SDA ↓ → SCL ↓ SCL clock L width SCL clock H width SCL clock frequency (Repeated) START condition hold time SDA ↓ → SCL ↓ Data setup time SDA ↓ ↑ → SCL ↑ Stop condition setup time SCL ↑ → SDA ↑ Bus free time between "Stop condition" and "START condition" Noise filter Symbol Conditions Fast Mode Plus (Fm+)*6 Unit fSCL Min 0 Max 1000 kHz tHDSTA 0.26 - μs tLOW tHIGH tSUSTA 0.5 0.26 0.26 - μs μs μs 0 0.45*2, *3 μs tSUDAT 50 - ns tSUSTO 0.26 - μs tBUF 0.5 - μs 6 tCYCP*4 - ns 8 tCYCP*4 - ns tHDDAT tSP CL = 30 pF, R = (Vp/IOL)*1 60 MHz ≤ tCYCP＜80 MHz 80 MHz ≤ tCYCP ≤100 MHz Remarks *5 *1: R and CL represent the pull-up resistance and load capacitance of the SCL and SDA lines, respectively. Vp indicates the power supply voltage of the pull-up resistance and IOL indicates VOL guaranteed current. *2: The maximum tHDDT must not extend beyond the low period (tLOW) of the device’s SCL signal. *3: The Fast mode I2C bus device can be used on a Standard-mode I2C bus system as long as the device satisfies the requirement of "tSUDAT ≥ 250 ns.” *4: tCYCP is the APB bus clock cycle time. For more information about the APB bus number to which the I2C is connected, see "8.Block Diagram" in this data sheet. To use fast mode plus (Fm+), set the peripheral bus clock at 64 MHz or more. *5: The noise filter time can be changed by register settings. Change the number of the noise filter steps according to the APB bus clock frequency. *6: When using fast mode plus (Fm+), set the I/O pin to the mode corresponding to I2C Fm+ in the EPFR register. See Chapter12: I/O PORT in FM4 Family Peripheral Manual Main Part (002-04856) for the details. Document Number: 002-04988 Rev. *C Page 164 of 198 S6E2C3 Series 12.4.16 SD Card Interface Timing Default-Speed Mode  Clock CLK (All values are referenced to VIH and VIL transition points) (VCC = 2.7 V to 3.6 V, VSS = 0 V) Parameter Symbol Pin Name fPP S_CLK fOD S_CLK tWL tWH tTLH tTHL S_CLK S_CLK S_CLK S_CLK Clock frequency Data Transfer Mode Clock frequency Identification Mode Clock low time Clock high time Clock rise time Clock fall time Conditions Min CCARD ≤ 10 pF (1card) Value Max Remarks 0 25 MHz 0/100 400 kHz 10 10 - 10 10 ns ns ns ns * 0 Hz means to stop the clock. The given minimum frequency range is for cases where a continuous clock is required.  Card Inputs CMD, DAT (referenced to Clock CLK) Parameter Symbol Input set-up time tISU Input hold time tIH Pin Name Conditions S_CMD, S_DATA3: 0 S_CMD, S_DATA3: 0 CCARD ≤ 10 pF (1card) Min Output Delay time during Data Transfer Mode Output Delay time during Identification Mode Symbol tODLY tODLY Pin Name Conditions S_CMD, S_DATA3: 0 S_CMD, S_DATA3: 0 CCARD ≤ 40 pF (1card) ns 5 - ns Value Max 0 14 ns 0 50 ns VIH VIH VIH VIL VIL tTLH tTHL tIH VIH VIH VIL VIL tODLY(Min) tODLY(Max) S_CMD, S_DATA3: 0 (Card Output) Remarks tWH tISU S_CMD, S_DATA3: 0 (Card Input) Remarks - Min tWL S_CLK (SD Clock) Max 5  Card Outputs CMD, DAT (referenced to Clock CLK) Parameter Value VOH VOH VOL VOL Default-Speed Mode Notes: − The Card Input corresponds to the Host Output and the Card Output corresponds to the Host Input because this model is the Host. − For more information about clock frequency (fPP), see Chapter 15: SD card Interface in FM4 Family Peripheral Manual Main Part (002-04856). Document Number: 002-04988 Rev. *C Page 165 of 198 S6E2C3 Series High-Speed Mode  Clock CLK (All values are referred to VIH and VIL) (VCC = 2.7 V to 3.6 V, VSS = 0 V) Parameter Symbol Pin Name fPP S_CLK Clock frequency Data Transfer Mode Clock low time Clock high time Clock rise time Clock fall time tWL tWH tTLH tTHL Conditions Min CCARD ≤ 10 pF (1 card) S_CLK S_CLK S_CLK S_CLK Symbol Input set-up time tISU Input hold time tIH Pin Name Conditions S_CMD, S_DATA3: 0 S_CMD, S_DATA3: 0 CCARD ≤ 10 pF (1 card) Symbol Output delay time during data transfer mode tODLY Output hold time tOH Total system capacitance for each line* CL Pin Name Conditions S_CMD, S_DATA3: 0 S_CMD, S_DATA3: 0 CL ≤ 40 pF (1 card) CL ≥ 15 pF (1 card) - 1 card Remarks 50 MHz 7 7 - 3 3 ns ns ns ns Min Value Max Remarks 6 - ns 2 - ns  Card Outputs CMD, DAT (referenced to Clock CLK) Parameter Max 0  Card Inputs CMD, DAT (referenced to Clock CLK) Parameter Value Min Value Max Remarks 0 14 ns 2.5 - ns - 40 pF *: In order to satisfy severe timing, host shall drive only one card. tWH tWL S_CLK (SD Clock) 50%VCC VIH VIH VIL VIL 50%VCC tTLH tTHL tIH tISU S_CMD, S_DATA3: 0 (Card Input) tODLY(Max) S_CMD, S_DATA3: 0 (Card Output) VIH VIH VIH VIL VIL tOH(Min) VOH VOH VOL VOL High-Speed Mode Notes: − The Card Input corresponds to the Host Output and the Card Output corresponds to the Host Input because this model is the Host. − For more information about clock frequency (fPP), see Chapter 15: SD card Interface in FM4 Family Peripheral Manual Main Part (002-04856). Document Number: 002-04988 Rev. *C Page 166 of 198 S6E2C3 Series 12.4.17 ETM/ HTM Timing (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Data hold Symbol Pin Name Conditions tETMH TRACECLK, TRACED[15: 0] TRACECLK frequency 1/tTRACE TRACECLK clock cycle tTRACE TRACECLK Value Unit Min Max VCC ≥ 4.5 V 2 9 ns VCC ＜4.5 V VCC ≥ 4.5 V VCC ＜4.5 V 2 15 50 32 MHz MHz VCC ≥ 4.5 V 20 - ns VCC ＜4.5 V 31.25 - ns Remarks Note: − When the external load capacitance CL = 30 pF. HCLK TRACECLK TRACED[15: 0] Document Number: 002-04988 Rev. *C Page 167 of 198 S6E2C3 Series 12.4.18 JTAG Timing (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol Pin Name Conditions TMS, TDI setup time tJTAGS TCK, TMS, TDI VCC ≥ 4.5 V VCC ＜4.5 V TMS, TDI hold time tJTAGH TCK, TMS, TDI TDO delay time tJTAGD TCK, TDO VCC ≥ 4.5 V VCC ＜4.5 V VCC ≥ 4.5 V VCC ＜4.5 V Value Unit Min Max 15 - ns 15 - ns - 25 45 ns Remarks Note: − When the external load capacitance CL = 30 pF. TCK TMS/TDI TDO Document Number: 002-04988 Rev. *C Page 168 of 198 S6E2C3 Series 12.4.19 I2S Timing Master Mode Timing (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol Pin Name Conditions fMCYC tMHW I2SCK - I2SCK - Output frequency Output clock pulse width I2SCK→I2SWS delay time I2SCK→I2SDO delay time* I2SDI→I2SCK setup time I2SDI→I2SCK hold time Input signal rise time Input signal fall time tMLW tDFS tDDO tHSDI tHDI tFI tFI I2SCK, I2SWS I2SCK, I2SDO I2SCK, I2SDI I2SDI Value Unit Min Max 45 12.288 55 MHz % 45 55 % - 0 24.0 ns - 0 24.0 ns - 25.0 - ns - 0 - ns - - 5 ns - - 5 ns Remarks *: Except for the first bit of transmission frame Notes: − When the external load capacitance CL = 20 pF − When I2SWS = 48 kHz, I2MCLK = 256 × I2SWS Frame synchronization signal (I2SWS) is settable to 48 kHz, 32 kHz, 16 kHz. See Chapter7-2: I2S (Inter-IC Sound bus) Interface in FM4 Family Peripheral Manual Communication Macro Part (002-04862) for the details. Document Number: 002-04988 Rev. *C Page 169 of 198 S6E2C3 Series tmcyc tmhw tmlw I2SCK (CPOL=0) I2SCK (CPOL=1) tdfs I2SWS (FSPH=0, FSLN=0) tdfs tdfs tdfs I2SWS (FSPH=1, FSLN=0) tdfs tdfs I2SWS (FSPH=0, FSLN=1) tdfs tdfs I2SWS (FSPH=1, FSLN=1) tddo I2SDO tsdi thdi tsdi thdi I2SDI (SMPL=0) tsdi thdi I2SDI (SMPL=1) Note: − See Chapter7-2: I2S (Inter-IC Sound bus) Interface in FM4 Family Peripheral Manual Communication Macro Part (002-04862) for the details of CPOL, FSPH, FSLIN, and SMPL. I2SDI 0.8×VCC 0.8×VCC 0.2×VCC tfi Document Number: 002-04988 Rev. *C 0.8×VCC 0.2×VCC tri Page 170 of 198 S6E2C3 Series Slave Mode Timing (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Input frequency Input clock pulse width Symbol Pin Name Conditions fSCYC tSHW I2SCK - I2SCK - I2SWS→I2SCK Setup time I2SWS→I2SCK Hold time I2SCK↑→I2SDO Delay time*1 I2SCK↑→I2SDO Delay time*2 I2SDI→I2SCK↓ Setup time I2SDI→I2SCK↓ Hold time Input signal rise time Input signal fall time tSLW tSFI tHFI I2SCK, I2SWS I2SCK, I2SWS tDDO Value Unit Min Max 45 12.288 55 MHz % 45 55 % - 8 - ns - 0 - ns - 0 32 ns - 0 32 ns - 8 - ns - 0 - ns - - 5 ns - - 5 ns Remarks I2SCK, I2SDO tDFB1 tSDI I2SCK, I2SDI tHDI tFI tFI I2SCK, I2SWS, I2SDI *1: Except for the first bit of transmission frame *2: When FSPH bit = 1. Notes: − When the external load capacitance CL = 20 pF − When I2SWS = 48 kHz, I2MCLK = 256×I2SWS Frame synchronization signal (I2SWS) is settable to 48 kHz, 32 kHz, 16 kHz. See Chapter7-2: I2S (Inter-IC Sound bus) Interface in FM4 Family Peripheral Manual Communication Macro Part (002-04862) for the details. Document Number: 002-04988 Rev. *C Page 171 of 198 S6E2C3 Series tscyc tshw tslw I2SCK (CPOL=0) I2SCK (CPOL=1) tsfi thfi I2SWS (FSPH=0, FSLN=0) tsfi thfi I2SWS (FSPH=1, FSLN=0) tsfi I2SWS (FSPH=0, FSLN=1) tsfi I2SWS (FSPH=1, FSLN=1) tddo tdfb1 I2SDO tsdi thdi tsdi thdi I2SDI (SMPL=0) tsdi thdi I2SDI (SMPL=1) Notes: − See Chapter7-2: I2S (Inter-IC Sound bus) Interface in FM4 Family Peripheral Manual Communication Macro Part (002-04862) for the details of FSPH, FSLN, SMPL − I2SCK input is selectable polarity by CPOL bit of CNTREG register I2SCK I2SWS I2SDI 0.8×VCC 0.8×VCC 0.2×VCC tfi Document Number: 002-04988 Rev. *C 0.8×VCC 0.2×VCC tri Page 172 of 198 S6E2C3 Series I2SMCLK Input Characteristics (VCC = 2.7 V to 5.5 V, VSS = 0 V) Symbol Pin Name Conditions Input frequency fCHS I2SMCK Input clock cycle tCYLHS - - - tCFS tCRS - Parameter Input clock pulse width Input clock rise time and fall time Value Unit Min Max - - 25 MHz PWHS/tCYLHS PWLS/tCYLHS 40 - ns 45 55 % - - 5 ns Remarks When using external clock When using external clock tCYLHS I2SMCLK 0.8×VCC 0.8×VCC 0.8×VCC 0.2×VCC PWHS 0.2×VCC PWLS tCFS tCRS I2SMCLK Output Characteristics (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol Pin Name Conditions fCHS I2SMCK - Output frequency Document Number: 002-04988 Rev. *C Value Min Max - 12.288 Unit Remarks MHz Page 173 of 198 S6E2C3 Series 12.4.20 High-Speed Quad SPI Timing (VCC = 2.7 V to 3.6 V, VSS = 0 V) Parameter Serial clock frequency Enabled CS→ CLK Starting Time (mode0/mode2) Enabled CS→ CLK Starting Time (mode1/mode3) CLK Last→ Disabled CS Time (mode0/mode2) CLK Last→ Disabled CS Time (mode1/mode3) SIO Data output time Symbol tSCYCM Pin Name Q_SCK_0 Conditions Unit Remarks 66 MHz *1 - 50 MHz *2 1.5×tSCYCM - 5 - ns tSCYCM - 5 - ns tSCYCM - ns 1.5×tSCYCM - ns CL = 15 pF, VCC = 3.0 to 3.6V 0 5 ns CL = 30 pF 0 5 3 10 0.5×tSCYCM - Max CL = 15 pF, VCC = 3.0 to 3.6V - CL = 30 pF tOSLSK02 tOSLSK13 tOSKSL02 Q_SCK_0, Q_CS0_0, Q_CS1_0, Q_CS2_0 CL = 30 pF tOSKSL13 tOSDAT SIO Setup tDSSET SIO Hold tSDHOLD Q_SCK_0, Q_IO0_0, Q_IO1_0, Q_IO2_0, Q_IO3_0 Value Min CL = 30 pF CL = 30 pF ns *1 *2 ns *1: When RTM = 1 and mode = 0, 1, 3 *2: When RTM = 1 and mode = 2 or RTM = 0 and mode = 0, 1, 2, 3 Notes: − See Chapter8-3: High-Speed Quad SPI controller in FM4 Family Peripheral Manual Communication Macro Part (002-04862) for the detail of RTM mode. − When using High-Speed Quad SPI, please set PDSR register to set the pin drive capability for VCC = 3 V. See Chapter12: I/O Port in FM4 Family Peripheral Manual Main Part (002-04856) for the details. Document Number: 002-04988 Rev. *C Page 174 of 198 S6E2C3 Series Q_CS0, Q_CS1, Q_CS2 tSCYCM mode0 mode2 tOSLSK02 Q_SCK tOSKSL02 mode1 mode3 tOSKSL13 tOSLSK13 input Q_IO0, Q_IO1, Q_IO2, Q_IO3 tDSSET tSDHOLD output tOSDAT Document Number: 002-04988 Rev. *C Page 175 of 198 S6E2C3 Series 12.5 12-bit A/D Converter Electrical Characteristics for the A/D Converter (VCC = AVCC = 2.7 V to 5.5 V, VSS = AVSS = AVRL = 0 V) Parameter Symbol Pin Name Resolution Integral nonlinearity Differential nonlinearity Zero transition voltage Full-scale transition voltage VZT ANxx VFST ANxx Conversion time - - Sampling time *2 Ts - Compare clock cycle*3 Tcck - State transition time to operation permission Tstt - Power supply current (analog + digital) - AVCC Reference power supply current (AVRH) - AVRH Analog input capacity CAIN Analog input resistance Value Unit Remarks Min Typ Max - 4.5 - 2.5 - 15 AVRH – 15 AVCC - 15 - 12 + 4.5 + 2.5 + 15 AVRH + 15 AVCC + 15 bit LSB LSB mV mV mV 0.5*1 - - μs 0.15 0.3 25 - 10 μs 1000 50 - 1000 - - 1.0 μs - 0.69 0.92 mA A/D 1 unit operation - 1.3 22 μA When A/D stop - 1.1 1.97 mA A/D 1 unit operation AVRH = 5.5 V - 0.3 6.3 μA When A/D stop - - - pF RAIN - - - Interchannel disparity Analog port input leak current - - - - 12.05 1.2 1.8 4 LSB - ANxx - - 5 μA Analog input voltage - ANxx AVRH - AVRL - AVRH AVCC AVCC AVCC AVSS V V - AVSS AVSS 4.5 2.7 AVSS Reference voltage ns kΩ V AVRH = 2.7 V to 5.5 V AVCC ≥ 4.5 V AVCC ≥ 4.5 V AVCC < 4.5 V AVCC ≥ 4.5 V AVCC < 4.5 V AVCC ≥ 4.5 V AVCC < 4.5 V Tcck ＜ 50 ns Tcck ≥ 50 ns V *1: The conversion time is the value of sampling time (Ts) + compare time (Tc). The condition of the minimum conversion time is when the value of Ts = 150 ns and Tc = 350 ns (AVCC ≥ 4.5V). Ensure that it satisfies the value of sampling time (Ts) and compare clock cycle (Tcck). For setting of sampling time and compare clock cycle, see Chapter 1-1: A/D Converter in FM4 Family Peripheral Manual Analog Macro Part (002-04860). The register setting of the A/D converter is reflected by the APB bus clock timing. For more information about the APB bus number to which the A/D converter is connected, see 8. Block Diagram in this data sheet. The sampling and compare clock are set at base clock (HCLK). *2: A necessary sampling time changes by external impedance. Ensure that it sets the sampling time to satisfy (Equation 1). *3: The compare time (Tc) is the value of (Equation 2). Document Number: 002-04988 Rev. *C Page 176 of 198 S6E2C3 Series AN00 to AN31 Analog input pin Rext Comparator R AIN Rin Analog signal source Cin CAIN (Equation 1) Ts ≥ (RAIN + Rext) × CAIN × 9 Ts: Sampling time RAIN: Input resistance of A/D = 1.2 kΩ at 4.5 V ≤ AVCC ≤ 5.5 V Input resistance of A/D = 1.8 kΩ at 2.7 V ≤ AVCC < 4.5 V CAIN: Input capacity of A/D = 12.05 pF at 2.7 V ≤ AVCC ≤ 5.5 V Rext: Output impedance of external circuit (Equation 2) Tc = Tcck × 14 Tc: Compare time Tcck: Compare clock cycle Document Number: 002-04988 Rev. *C Page 177 of 198 S6E2C3 Series Definition of 12-bit A/D Converter Terms  Resolution: Analog variation that is recognized by an A/D converter.  Integral Nonlinearity: Deviation of the line between the zero-transition point (0b000000000000 ←→ 0b000000000001) and the full-scale transition point (0b111111111110 ←→ 0b111111111111) from the actual conversion characteristics.  Differential Nonlinearity: Deviation from the ideal value of the input voltage that is required to change the output code by 1 LSB. Integral Nonlinearity 0xFFF Actual conversion characteristics 0xFFE Actual conversion characteristics 0x(N+1) {1 LSB(N-1) + VZT} VFST VNT 0x004 (Actually-measured value) 0x003 0x002 0x001 (Actuallymeasured value) Digital output Digital output 0xFFD Differential Nonlinearity Actual conversion characteristics Ideal characteristics 0xN Ideal characteristics VNT Actual conversion characteristics AVRH AVss Analog input Integral Nonlinearity of digital output N = Differential Nonlinearity of digital output N = 1LSB = (Actually-measured value) (Actually-measured value) 0x(N-2) VZT (Actually-measured value) AVss V(N+1)T 0x(N-1) AVRH Analog input VNT - {1LSB × (N - 1) + VZT} 1LSB V(N + 1) T - VNT 1LSB [LSB] - 1 [LSB] VFST - VZT 4094 N: A/D converter digital output value. VZT: Voltage at which the digital output changes from 0x000 to 0x001. VFST: Voltage at which the digital output changes from 0xFFE to 0xFFF. VNT: Voltage at which the digital output changes from 0x(N − 1) to 0xN. Document Number: 002-04988 Rev. *C Page 178 of 198 S6E2C3 Series 12.6 12-bit D/A Converter Electrical Characteristics for the D/A Converter (VCC = AVCC = 2.7 V to 5.5 V, VSS = AVSS = 0 V) Parameter Resolution Symbol Integral nonlinearity * Differential nonlinearity * tC20 tC100 INL DNL Output voltage offset VOFF Conversion time Analog output impedance Power supply current * Pin Name DAx RO IDDA IDSA AVCC Min 0.56 2.79 - 16 - 0.98 - 20.0 3.10 2.0 Value Typ 0.69 3.42 3.80 - Max 12 0.81 4.06 + 16 + 1.5 + 10 + 1.4 4.50 - 260 330 410 μs 400 510 620 μs - - 14 μs Unit bit μs μs LSB LSB mV mV kΩ MΩ Remarks Load 20 pF Load 100 pF When setting 0x000 When setting 0xFFF D/A operation When D/A stop D/A 1ch operation AVCC = 3.3 V D/A 1ch operation AVCC = 5.0 V When D/A stop *: During no load Document Number: 002-04988 Rev. *C Page 179 of 198 S6E2C3 Series 12.7 USB Characteristics (VCC = AVCC = 2.7 V to 5.5 V, USBVCC0 = USBVCC1 = 3.0 V to 3.6 V, VSS = AVSS = 0 V) Parameter Input characteristics Output characteristics Symbol Pin Name Conditions Value Min Max Unit Remarks V *1 V *1 Input H level voltage VIH - 2.0 Input L level voltage Differential input sensitivity Different common mode range VIL - VSS - 0.3 USBVCC + 0.3 0.8 VDI - 0.2 - V *2 VCM - 0.8 2.5 V *2 2.8 3.6 V *3 0.0 0.3 V *3 1.3 4 4 2.0 20 20 V ns ns *4 *5 *5 Output H level voltage VOH Output L level voltage VOL Crossover voltage Rise time Fall time Rise/fall time matching Output impedance VCRS tFR tFF Rise time Fall time Rise/fall time matching UDP0/ UDM0, UDP1/ UDM1 External pulldown resistance = 15 kΩ External pull-up resistance = 1.5 kΩ Full-Speed Full-Speed tFRFM Full-Speed 90 111.11 % *5 ZDRV Full-Speed 28 44 Ω *6 tLR tLF Low-Speed Low-Speed 75 75 300 300 ns ns *7 *7 tLRFM Low-Speed 80 125 % *7 *1: The switching threshold voltage of the single-end-receiver of USB I/O buffer is set as within VIL (Max) = 0.8 V, VIH (Min) = 2.0 V (TTL input standard). There is some hysteresis applied to lower noise sensitivity. *2: Use differential-receiver to receive USB differential data signal. Differential-receiver has 200 mV of differential input sensitivity when the differential data input is within 0.8 V to 2.5 V to the local ground reference level. Minimum differential input sensitivity [V] Above voltage range is the common mode input voltage range. Common mode input voltage [V] Document Number: 002-04988 Rev. *C Page 180 of 198 S6E2C3 Series *3: The output drive capability of the driver is below 0.3 V at low state (VOL) (to 3.6 V and 1.5 kΩ load), and 2.8 V or above (to the VSS and 1.5 kΩ load) at high state (VOH). *4: The cross voltage of the external differential output signal (D +/D −) of USB I/O buffer is within 1.3 V to 2.0 V. VCRS specified range *5: They indicate rise time (Trise) and fall time (Tfall) of the full-speed differential data signal. They are defined by the time between 10% and 90% of the output signal voltage. For full-speed buffer, Tr/Tf ratio is regulated as within ± 10% to minimize RFI emission. Rise time Document Number: 002-04988 Rev. *C Falling time Page 181 of 198 S6E2C3 Series *6: USB Full-speed connection is performed via twisted-pair cable shield with 90 Ω ± 15% characteristic impedance (differential mode). USB standard defines that the output impedance of the USB driver must be in the range from 28 Ω to 44 Ω. So, a discrete series resistor (Rs) addition is defined in order to satisfy the above definition and keep balance. When using this USB I/O, use it with 25 Ω to 30 Ω (recommended value 27 Ω) series resistor Rs. 28 Ω to 44 Ω Equiv. Imped. 28 Ω to 44 Ω Equiv. Imped. Mount it as external resistance. Rs series resistor 25 Ω to 30 Ω Series resistor of 27 Ω (recommendation value) must be added. And, use "resistance with an uncertainty of 5% by E24 sequence.” *7: They indicate rise time (Trise) and fall time (Tfall) of the low-speed differential data signal. They are defined by the time between 10% and 90% of the output signal voltage. Rise time Falling time Note: − See Low-Speed Load (Compliance Load) for conditions of external load. Document Number: 002-04988 Rev. *C Page 182 of 198 S6E2C3 Series Low-Speed Load (Upstream Port Load) - Reference 1 CL=50pF to 150pF CL=50pF to 150pF Low-Speed Load (Downstream Port Load) - Reference 2 CL= 200pF to 600pF CL= 200pF to 600pF Low-Speed Load (Compliance Load) CL=200pF to 450pF CL=200pF to 450pF Document Number: 002-04988 Rev. *C Page 183 of 198 S6E2C3 Series 12.8 Low-Voltage Detection Characteristics 12.8.1 Low-Voltage Detection Reset Parameter Detected voltage Released voltage 12.8.2 Symbol Conditions VDL VDH - Min 2.46 2.51 Value Typ 2.55 2.60 Min Typ Max 2.80 2.90 2.99 3.09 3.18 3.28 3.67 3.76 3.76 3.86 4.05 4.15 4.15 4.25 4.25 4.34 2.90 3.00 3.10 3.20 3.30 3.40 3.80 3.90 3.90 4.00 4.20 4.30 4.30 4.40 4.40 4.50 3.00 3.11 3.21 3.31 3.42 3.52 3.93 4.04 4.04 4.14 4.35 4.45 4.45 4.55 4.55 4.66 V V V V V V V V V V V V V V V V - - 6000 × tCYCP* µs Max 2.64 2.69 Unit V V Remarks When voltage drops When voltage rises Interrupt of Low-Voltage Detection Parameter Symbol Detected voltage Released voltage Detected voltage Released voltage Detected voltage Released voltage Detected voltage Released voltage Detected voltage Released voltage Detected voltage Released voltage Detected voltage Released voltage Detected voltage Released voltage VDL VDH VDL VDH VDL VDH VDL VDH VDL VDH VDL VDH VDL VDH VDL VDH LVD stabilization wait time TLVDW Conditions SVHI = 00111 SVHI = 00100 SVHI = 01100 SVHI = 01111 SVHI = 01110 SVHI = 01001 SVHI = 01000 SVHI = 11000 - Value Unit Remarks When voltage drops When voltage rises When voltage drops When voltage rises When voltage drops When voltage rises When voltage drops When voltage rises When voltage drops When voltage rises When voltage drops When voltage rises When voltage drops When voltage rises When voltage drops When voltage rises *: tCYCP indicates the APB2 bus clock cycle time. Document Number: 002-04988 Rev. *C Page 184 of 198 S6E2C3 Series 12.9 MainFlash Memory Write/Erase Characteristics (VCC = 2.7 V to 5.5 V) Parameter Min Value Typ Max Unit Large Sector - 0.7 3.7 s Small Sector - 0.3 1.1 s Write cycles < 100 times Write cycles > 100 times - 12 100 200 μs Not including system-level overhead time - 13.6 68 s Includes write time prior to internal erase Sector erase time Half word (16-bit) write time Remarks Chip erase time* Includes write time prior to internal erase *: It indicates the chip erase time of 1 MB MainFlash memory For devices with 1.5 MB or 2 MB of MainFlash memory, two erase cycles are required. See 3.2.2 Command Operating Explanations and 3.3.3 Flash Erase Operation in this product's Flash Programming Manual for the detail. Write Cycles and Data Retention Time Erase/Write Cycles (Cycle) Data Retention Time (Year) 1,000 20* 10,000 10* 100,000 5* *: This value comes from the technology qualification (using Arrhenius equation to translate high temperature acceleration test result into average temperature value at + 85°C). 12.10 Dual Flash Memory Write/Erase Characteristics It is the same write/erase characteristics as the MainFlash memory. See 3.6 Dual flash mode in this product's Flash Programming Manual for the detail of dual flash mode. Document Number: 002-04988 Rev. *C Page 185 of 198 S6E2C3 Series 12.11 Standby Recovery Time 12.11.1 Recovery cause: Interrupt/WKUP The time from the interrupt occurring to the time of program operation start is shown. Recovery Count Time (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Value Symbol Sleep mode High-speed CR Timer mode Main Timer mode PLL Timer mode Unit Max* Typ HCLK×1 μs 40 80 μs Low-speed CR Timer mode 450 900 μs Sub Timer mode 896 1136 μs 316 581 μs 270 540 μs 365 667 μs 365 667 μs RTC mode Stop mode (High-speed CR/Main/PLL Run mode return) RTC mode Stop mode (Low-speed CR/sub Run mode return) tICNT Deep Standby RTC mode with RAM retention Deep Standby Stop mode with RAM retention Remarks without RAM retention with RAM retention *: The maximum value depends on the built-in CR accuracy. Example of Standby Recovery Operation (when in External Interrupt Recovery*) Ext.INT Interrupt factor accept Active tICNT CPU Operation Interrupt factor clear by CPU Start *: External interrupt is set to detecting fall edge. Document Number: 002-04988 Rev. *C Page 186 of 198 S6E2C3 Series Example of Standby Recovery Operation (when in Internal Resource Interrupt Recovery*) Internal Resource INT Interrupt factor accept Active tICNT CPU Operation Interrupt factor clear by CPU Start *: Depending on the standby mode, interrupt from the internal resource is not included in the recovery cause. Notes: − The return factor is different in each low-power consumption mode. See Chapter 6: Low Power Consumption Mode and Operations of Standby Modes in FM4 Family Peripheral Manual Main Part (002-04856). − The recovery process is unique for each operating mode. See Chapter 6: Low Power Consumption Mode in FM4 Family Peripheral Manual Main Part (002-04856). Document Number: 002-04988 Rev. *C Page 187 of 198 S6E2C3 Series 12.11.2 Recovery Cause: Reset The time from reset release to the program operation start is shown. Recovery Count Time (VCC = 2.7 V to 5.5 V, VSS = 0 V) Parameter Symbol Value Unit Typ Max* Sleep mode High-speed CR Timer mode Main Timer mode PLL Timer mode 155 266 µs 155 266 µs Low-speed CR Timer mode 315 567 µs 315 567 µs 315 567 µs 336 667 µs 336 667 µs tRCNT Sub Timer mode RTC mode Stop mode Deep Standby RTC mode with RAM retention Deep Standby Stop mode with RAM retention Remarks without RAM retention with RAM retention *: The maximum value depends on the built-in CR accuracy. Example of Standby Recovery Operation (when in INITX Recovery) INITX Internal RST RST Active Release tRCNT CPU Operation Document Number: 002-04988 Rev. *C Start Page 188 of 198 S6E2C3 Series Example of Standby Recovery Operation (when in Internal Resource Reset Recovery*) Internal Resource RST Internal RST RST Active Release tRCNT CPU Operation Start *: Depending on the low-power consumption mode, the reset issue from the internal resource is not included in the recovery cause. Notes: − The return factor is different in each low power consumption mode. See Chapter 6: Low Power Consumption Mode and Operations of Standby Modes in FM4 Family Peripheral Manual Main Part (002-04856). − The recovery process is unique for each operating mode. See Chapter 6: Low Power Consumption Mode in FM4 Family Peripheral Manual Main Part (002-04856). − When the power-on reset/low-voltage detection reset, they are not included in the return factor. See 12.4.8 Power-On Reset Timing. − In recovering from reset, CPU changes to High-speed Run mode. In the case of using the main clock and PLL clock, they need further main clock oscillation stabilization wait time and oscillation stabilization wait time of Main PLL clock. − Internal resource reset indicates Watchdog reset and CSV reset. Document Number: 002-04988 Rev. *C Page 189 of 198 S6E2C3 Series 13. Ordering Information Part number Flash RAM Crypto S6E2C38H0AGV2000A 1 MB 128 KB N/A S6E2C39H0AGV2000A 1.5 MB 192 KB N/A S6E2C3AH0AGV2000A 2 MB 256 KB N/A S6E2C38J0AGV2000A 1 MB 128 KB N/A S6E2C39J0AGV2000A 1.5 MB 192 KB N/A S6E2C3AJ0AGV2000A 2 MB 256 KB N/A S6E2C38J0AGB1000A 1 MB 128 KB N/A S6E2C39J0AGB1000A 1.5 MB 192 KB N/A S6E2C3AJ0AGB1000A 2 MB 256 KB N/A S6E2C38L0AGL2000A 1 MB 128 KB N/A S6E2C39L0AGL2000A 1.5 MB 192 KB N/A S6E2C3AL0AGL2000A 2 MB 256 KB N/A Document Number: 002-04988 Rev. *C Package Plastic・LQFP (0.5-mm pitch), 144 pin (LQS144) Plastic・LQFP (0.65-mm pitch), 176 pin (LQP176) Plastic・LQFP (0.8-mm pitch), 192 pin (LBE192) Plastic・LQFP (0.4-mm pitch), 216 pin (LQQ216) Page 190 of 198 S6E2C3 Series 14. Package Diagrams Package Type Package Code LQFP 144 LQS 144 002-13015 *A Document Number: 002-04988 Rev. *C Page 191 of 198 S6E2C3 Series Package Type Package Code LQFP 176 LQP 176 D D1 132 4 5 7 89 133 89 88 132 133 88 E1 E 5 7 4 3 6 176 45 1 176 45 44 44 1 2 5 7 e 3 BOTTOM VIEW 0.10 C A-B D 0.20 C A-B D b 0.08 C A-B D 8 TOP VIEW 2 A A' 0.08 C SIDE VIEW SYM BOL NOM . M AX. 0.05 0.15 L1 0.25 A1 10 L c b SECTION A-A' 1.70 b 0.17 c 0.09 0.22 26.00 BSC D1 24.00 BSC e 0.50 BSC E 26.00 BSC E1 0.27 0.20 D 24.00 BSC L 0.45 0.60 0.75 L1 0.30 0.50 0.70 θ SEA TIN G PLAN E DIM ENSIONS M IN. A A1 9 θ A 0° 8° 002-15150 ** PACKAGE OUTLINE, 176 LEAD LQFP 24.0X24.0X1.7 M M LQP176 REV** Document Number: 002-04988 Rev. *C Page 192 of 198 S6E2C3 Series Package Type Package Code LQFP 216 LQQ 216 4 D 5 7 D1 162 109 1 09 108 163 162 108 163 E1 E 5 4 7 3 6 55 216 1 55 216 54 1 54 e 2 5 7 3 0.10 C A-B D 0.20 C A-B D b 0.07 C A-B D BOTTOM VIEW 8 TOP VIEW 2 A θ A A' SEA TIN G PLAN E L1 0.08 C 9 0.25 L A1 10 c b SECTION A-A' SIDE VIEW SYM BOL DIM ENSIONS M IN. NOM . M AX. 0.05 0.15 1.70 A A1 b 0.13 c 0.09 0.18 0.23 0.20 D 26.00 BSC. D1 24.00 BSC. e 0.40 BSC E 26.00 BSC. 24.00 BSC. E1 L 0.45 0.60 0.75 L1 0.30 0.50 0.70 θ 0° 8° 002-15153 ** PACKAGE OUTLINE, 216 LEAD LQFP 24.0X24.0X1.7 M M LQQ216 REV** Document Number: 002-04988 Rev. *C Page 193 of 198 S6E2C3 Series Package Type Package Code PFBGA 192 LBE 192 002-13493 *A Document Number: 002-04988 Rev. *C Page 194 of 198 S6E2C3 Series 15. Major Changes Spansion Publication Number: S6E2C3_DS709-00012 Page Section Revision 0.1 Revision 1.0 11 2. Features 13 3. Product Lineup 87 10. Block Diagram 88 12. Memory Map 16-18 5. Pin Assignments 20-71 6. Pin Descriptions 72-79 7. I/O Circuit Type - 94-101 102-103 13. Pin Status In Each CPU State 14.1. Absolute Maximum Ratings 104-107 14.2. Recommended Operating Conditions 108-117 14.3.1. Current Rating 118-119 14.3.2. Pin Characteristics 122 14.4.5. Operating Conditions of USB PLL・ I2S PLL (in the case of using main clock for input clock of PLL) 186 14.5.12-bit A/D Converter 194 14.8.2. Interrupt of Low-Voltage Detection Change Results Initial release Deleted HDM-CEC/Remote Control Receiver. Deleted the pins of HDM-CEC/Remote Control Receiver.(CEC0,CEC1) Revised the pin name of I2S. (MI2S*_0→MI2S*0_0) Deleted the pin of IGTRG0_0. Deleted the pins of HDM-CEC/Remote Control Receiver.(CEC0,CEC1) Revised the pin name of I2S. (MI2S*_0→MI2S*0_0) Revised the pin number of PF7 in LQFP216.(91→90) revised the pin number of X1. (73, 58, 50, P5→107, 87, 71, P13) Revised the pin number of X0A. (107, 87, 71, P13→73, 58, 50, P5) Revised IOH/IOL of Type S.(IOH=-12mA→-10mA, IOL=12mA→ 10mA) Added the case of using I2C in Type E, F, G, L, N, S. Deleted X and Y in Pin Status Type. Added 10mA type. Added AVRL in Analog reference voltage. Revised the leakage current in Maximum leakage current at operating Revised the maximum current of each category. Added the characteristic of external bus in H level input voltage (hysteresis input). Added the characteristic of 10 mA type. Revised the maximum of I2S PLL macro oscillation clock frequency. (307.2 MHz→384 MHz) Revised the minimum of Sampling time. Revised the characteristic of State transition time to operation permission Added AVRL in Analog reference voltage. Revised the SVHI values in Conditions NOTE: Please see “Document History” about later revised information. Document Number: 002-04988 Rev. *C Page 195 of 198 S6E2C3 Series Document History Document Title: S6E2C3 Series 32-bit ARM® Cortex®-M4F, FM4 Microcontroller Document Number: 002-04988 Orig. of Submission Change Date - AKIH 04/22/2015 5126421 HITK 02/05/2016 Revision ECN ** *A Description of Change New Spec. Company name and layout design change. Added the note of TAP pin. Updated Package Code and Dimensions (LQFP-144, LQFP-176, LQFP-216). Deleted CAN in communications interfaces. (Page 1) Deleted CAN(RX0_2, TX0_2) in LQQ216 pin assignments (Page 12) Deleted RX2_0 in P7D in “4. Pin Descriptions” (Page 20) Updated 12.4.8 Power-On Reset Timing. Changed parameter from “Power Supply rise time(tVCCR)[ms]” to “Power ramp rate(dV/dt)[mV/us]” and add some comments. (Page 113) Modified CSIO timing typo (12.4.12 CSIO(SPI) Timing) Deleted “SPI=1, MS=0” in the titles and added MS=0,1 in the schematic (Page 134-141, 150-157) Modified RTC description(Features, Real-Time Clock(RTC) ) Deleted “second , or day of the week” in the Interrupt function.(Page 3) Modifications related to the VBAT in the following chapter. “7. Handling Devices” Notes on Power-on (Page 76) “11. Pin Status in Each CPU State” List of VBAT Domain Pin Status (Page 90) “12.3.1 Current Rating” Table129. Typical and Maximum Current Consumption in Deep Standby STOP Mode, Deep Standby RTC Mode and VBAT (Page 105) Deleted MPNs below from “13. Ordering Information” (Page 190) *B 5634625 YSKA 02/20/2017 S6E2C38H0AGV20000, S6E2C38J0AGB10000, S6E2C38J0AGV20000, S6E2C38L0AGL20000, S6E2C39H0AGV20000, S6E2C39J0AGB10000, S6E2C39J0AGV20000, S6E2C39L0AGL20000, S6E2C3AH0AGV20000, S6E2C3AJ0AGB10000, S6E2C3AJ0AGV20000, S6E2C3AL0AGL20000 Added MPNs below to “13. Ordering Information” (Page 190) S6E2C38H0AGV2000A, S6E2C38J0AGB1000A, S6E2C38J0AGV2000A, S6E2C38L0AGL2000A, S6E2C39H0AGV2000A, S6E2C39J0AGB1000A, S6E2C39J0AGV2000A, S6E2C39L0AGL2000A, S6E2C3AH0AGV2000A, S6E2C3AJ0AGB1000A, S6E2C3AJ0AGV2000A, S6E2C3AL0AGL2000A Deleted Baud rate spec for High-Speed Synchronous Serial in “12.4.12 CSIO(SPI) Timing”(Page 142-148) Modified the expression of the “Built-in CR” and add Note in the “1. Product Lineup”(Page 8) Modified typo(SCLKx_0 -> SCKx_0)(Page 126, 128, 130, 132) Change the name from “USB Function” to “USB Device” (Page 1, 8, 58) Added Maximum Access size in “Features”(Page 1) Updated IO circuit (type A) (Page 62) Document Number: 002-04988 Rev. *C Page 196 of 198 S6E2C3 Series Updated Package Diagrams: Spec 002-13015 – Changed revision from ** to *A. *C 6095085 HUAL 03/12/2018 Spec 002-13493 – Changed revision from ** to *A. Updated to new template. Completing Sunset Review. Document Number: 002-04988 Rev. *C Page 197 of 198 S6E2C3 Series Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. PSoC® Solutions Products ARM® Cortex® Microcontrollers Automotive Clocks & Buffers Interface Internet of Things Memory cypress.com/arm cypress.com/automotive cypress.com/clocks cypress.com/interface cypress.com/iot cypress.com/memory Microcontrollers cypress.com/mcu PSoC cypress.com/psoc Power Management ICs cypress.com/pmic Touch Sensing USB Controllers Wireless Connectivity PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP | PSoC 6 MCU Cypress Developer Community Forums | WICED IOT Forums | Projects | Video | Blogs | Training | Components Technical Support cypress.com/support cypress.com/touch cypress.com/usb cypress.com/wireless ARM and Cortex are the registered trademarks of ARM Limited in the EU and other countries. © Cypress Semiconductor Corporation, 2014-2018. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC (“Cypress”). This document, including any software or firmware included or referenced in this document (“Software”), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress’s patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited. TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the device or system could cause personal injury, death, or property damage (“Unintended Uses”). A critical component is any component of a device or system whose failure to perform can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products. Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners. Document Number: 002-04988 Rev. *C March 12, 2018 Page 198 of 198