1N4006

1N4001 THRU 1N4007 Features · The plastic package carries Underwrites Laboratory Flammability Classification 94V-0 · Construction utilizes void-free molded plastic technique · Low reverse leakage · High forward surge current capability · High temperature soldering guaranteed : 250℃/10 seconds, 0.375"(9.5mm) lead length, 5lbs.(2.3kg). CURRENT 1.0 Ampere VOLTAGE 50 to 1000 Volts DO-41 0.107(2.7) 0.080(2.0) DIA. 1.0(25.4) MIN. 0.205(5.2) 0.166(4.2) Mechanical Data · Case : JEDEC DO-41 molded plastic body · Terminals : Lead solderable per MIL-STD-750, method 2026 · Polarity : Color band denotes cathode end · Mounting Position : Any · Weight : 0.012 ounce, 0.33 gram 0.034(0.9) 0.028(0.7) DIA. 1.0(25.4) MIN. Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current 0.375"(9.5mm) lead length TA=75℃ Peak forward surge current 8.3ms half sine wave superimposed on rated load (JEDEC method) at TA=75℃ Maximum instantaneous forward voltage at 1.0A Maximum reverse current at rated DC blocking voltage TA=25℃ TA=100℃ VRRM VRMS VDC I(AV) IFSM VF IR RθJA RθJL CJ TA TJ TSTG 1N 4001 50 35 50 1N 4002 100 70 100 1N 4003 200 140 200 1N 4004 400 280 400 1.0 30.0 1.1 5.0 50.0 50.0 25.0 15.0 +150 1N 4005 600 420 600 1N 4006 800 560 800 1N 4007 1000 700 1000 Units Volts Volts Volts Amp Amps Volts μA ℃/W pF ℃ ℃ Typical thermal resistance (Note 2) Typical junction capacitance (Note 1) Maximum DC blocking voltage temperature Operating and storage temperature range -50 to +175 Notes: (1) Measured at 1MHz and applied reverse voltage of 4.0V DC. (2) Thermal resistance from junction to ambient and from junction to lead at 0.375"(9.5mm) lead length, P.C.B. mounted RATINGS AND CHARACTERISTIC CURVES 1N4001 THRU 1N4007 FIG.1-FORWARD CURRENT DERATING CURVE 1.0 AVERAGE FORWARD CURRENT AMPERES 0.8 INSTANTANEOUS FORWARD CURRENT(AMPERES) 0.6 0.4 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD FIG.2-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 20 10 0.2 0 0 1 25 50 75 100 125 150 175 TJ=25℃ LEAD TEMPERATURE ( ℃) 0.1 PULSE WIDTH=300μS 1% DUTY CYCLE FIG.3-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 50 40 30 20 10 0 1 10 NUMBER OF CYCLES AT 60Hz 100 INSTANTANEOUS REVERSE CURRENT (μA) 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 0.01 0.6 0.8 1.0 1.2 1.4 1.5 INSTANTANEOUS FORWARD VOLTAGE (VOLTS) PEAK FORWARD SURGE CURRENT (AMPERES) FIG.4-TYPICAL REVERSE CHARACTERISTICS 10 1.0 TJ=100℃ FIG.5-TYPICAL JUNCTION CAPACITANCE 100 JUNCTION CAPACITANCE(pF) 0.1 TJ=25℃ 0.01 TJ=25℃ 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) 10 1 0.1 1 10 100 REVERSE VOLTAGE. VOLTS