ES1B

ES1A THRU ES1J Features · For surface applications in order to optimize board space · Low profile package · Built-in strain relief, ideal for automated placement · Super fast recovery time · Glass passivated junction · Plastic package has Unerwrites Laboratory Flammability Classification 94V-0 · Ideally suited for use in very high frequency switching power supplies, inverters and as free wheeling diodes · Low forward voltage drop · Glass passivated chip junction · High temperature soldering guaranteed : 250℃/10 seconds, at terminals CURRENT 1.0 Ampere VOLTAGE 50 to 400 Volts DO-214AC (SMA) 0.058(1.47) 0.052(1.32) 0.110(2.79) 0.100(2.54) 0.177(4.50) 0.157(3.99) 0.012(0.31) 0.006(0.15) 0.090(2.29) 0.078(1.98) 0.060(1.52) 0.030(0.76) 0.005(0.127) MAX. 0.208(5.28) 0.194(4.93) Mechanical Data · Case : JEDEC SMA(DO-214AC) molded plastic body · Terminals : Plated axial lead solderable per MIL-STD-750, method 2026 · Polarity : Color band denotes cathode end · Mounting Position : Any · Weight : 0.002 ounce, 0.064 gram Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TL=120℃ Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum instantaneous forward voltage at 1.0A Maximum reverse current at rated voltage TA=25℃ TA=100℃ VRRM VRMS VDC I(AV) IFSM VF IR Trr RθJL RθJA CJ TJ TSTG ES1A 50 35 50 ES1B 100 70 100 ES1C 150 105 150 1.0 30.0 0.95 5.0 100 35 35.0 85.0 7.0 ES1D 200 140 200 ES1G 400 380 400 ES1J 600 420 600 Units Volts Volts Volts Amp Amps 1.25 Volts μA ns ℃/W pF ℃ Maximum reverse recovery time (Note 1) Typical thermal resistance (Note 3) Typical junction capacitance (Note 2) Operating unction and storage temperature range -55 to +150 Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. (3) P.C.B mounted on 0.2×0.2"(5.0×5.0mm) copper pad areas RATINGS AND CHARACTERISTIC CURVES ES1A THRU ES1J FIG.1-FORWARD CURRENT DERATING CURVE 1.2 AVERAGE FORWARD CURRENT AMPERES 30 1 PEAK FORWARD SURGE CURRENT(AMPERES) 0.8 0.6 0.4 0.2 0 80 90 100 110 120 130 140 150 RESISTIVE OR INDUCTIVE LOAD 0.2X0.2"(5.0X5.0mm) COPPER PAD AREAS FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 25 20 15 10 5 0 1 10 8.3ms SINGLE HALF SINE WAVE (JEDEC Method) at TL=120℃ 100 LEAD TEMPERATURE (℃) NUMBER OF CYCLES AT 60Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT(AMPERES) 50 10 FIG.4-TYPICAL REVERSE CHARACTERISTICS 1000 INSTANTANEOUS REVERSE CURRENT ,(mA) 100 TJ=125℃ 1 10 0.1 TJ=25℃ PULSE WIDTH=300mS 1% DUTY CYCLE 1 TJ=75℃ 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0.1 TJ=25℃ INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) FIG.5-TYPICAL JUNCTION CAPACITANCE 14 JUNCTIOIN CAPACITANCE(pF) 12 10 8 6 4 2 0 0.1 1 10 100 REVERSE VOLTAGE. VOLTS TJ=25℃ f=1.0MHz Vsig=50mVp-P FIG.6-TYPICAL TRANSIENT THERMAL IMPEDANCE 100 TRANSIENT THERMAL IMPEDANCE, ℃/W MOUNTED ON 0.2X0.2"(5X7mm) COPPER PAD AREAS 10 1 0.1 1 10 100 T, PULSE DURATION ,sec. RATINGS AND CHARACTERISTIC CURVES ES1A THRU ES1J FIG.1-FORWARD CURRENT DERATING CURVE 1.2 AVERAGE FORWARD CURRENT AMPERES 30 1 PEAK FORWARD SURGE CURRENT(AMPERES) 0.8 0.6 0.4 0.2 0 80 90 100 110 120 130 140 150 RESISTIVE OR INDUCTIVE LOAD 0.2X0.2"(5.0X5.0mm) COPPER PAD AREAS FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 25 20 15 10 5 0 1 10 8.3ms SINGLE HALF SINE WAVE (JEDEC Method) at TL=120℃ 100 LEAD TEMPERATURE (℃) NUMBER OF CYCLES AT 60Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT(AMPERES) 50 10 FIG.4-TYPICAL REVERSE CHARACTERISTICS 1000 INSTANTANEOUS REVERSE CURRENT ,(mA) 100 TJ=125℃ 1 10 0.1 TJ=25℃ PULSE WIDTH=300mS 1% DUTY CYCLE 1 TJ=75℃ 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0.1 TJ=25℃ INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) FIG.5-TYPICAL JUNCTION CAPACITANCE 14 JUNCTIOIN CAPACITANCE(pF) 12 10 8 6 4 2 0 0.1 1 10 100 REVERSE VOLTAGE. VOLTS TJ=25℃ f=1.0MHz Vsig=50mVp-P FIG.6-TYPICAL TRANSIENT THERMAL IMPEDANCE 100 TRANSIENT THERMAL IMPEDANCE, ℃/W MOUNTED ON 0.2X0.2"(5X7mm) COPPER PAD AREAS 10 1 0.1 1 10 100 T, PULSE DURATION ,sec.