ES2J

ES2A THRU ES2J Features · For surface applications in order optimize board space · Low profile package · Built-in strain relief, ideal for automated placement · Super fast recovery time · Plastic package has Unerwrites Laboratory Flammability Classification 94V-0 · Ideally suited for use in very high frequency switching power supplies, inverters and as free wheeling diodes · Low forward voltage drop · Glass passivated chip junction · High temperature soldering guaranteed : 250℃/10 seconds, at terminals CURRENT 2.0 Amperes VOLTAGE 50 to 400 Volts DO-214AA (SMB) 0.083(2.11) 0.075(1.91) 0.155(3.94) 0.130(3.30) 0.185(4.70) 0.160(4.06) 0.012(0.31) 0.006(0.15) 0.096(2.44) 0.083(2.13) 0.050(1.27) 0.030(0.76) 0.008(0.203) MAX. 0.220(5.59) 0.200(5.08) Mechanical Data · Case : JEDEC SMB(DO-214AA) molded plastic body · Terminals : Plated axial lead solderable per MIL-STD-750, method 2026 · Polarity : Color band denotes cathode end · Mounting Position : Any · Weight : 0.003 ounce, 0.093 gram Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TL=120℃ Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum instantaneous forward voltage at 2.0A Maximum reverse current at rated voltage TA=25℃ TA=125℃ VRRM VRMS VDC I(AV) IFSM VF IR Trr RθJL RθJA CJ TJ TSTG ES2A 50 35 50 ES2B 100 70 100 ES2C 150 105 150 2.0 50.0 0.95 5.0 350 35 20.0 75.0 18.0 ES2D 200 140 200 ES2G 400 280 400 ES2J 600 420 600 Units Volts Volts Volts Amps Amps 1.25 Volts μA μS ℃/W 200 Maximum reverse recovery time (Note 1) Typical thermal resistance (Note 3) Typical junction capacitance (Note 2) Operating junction and storage temperature range 15.0 -55 to +150 pF ℃ Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. (3) Units mounted on P.C.B 5.0×5.0mm(0.013mm thick) land areas RATINGS AND CHARACTERISTIC CURVES ES2A THRU ES2J FIG.1-FORWARD CURRENT DERATING CURVE 2.4 AVERAGE FORWARD CURRENT AMPERES 30 2.0 PEAK FORWARD SURGE CURRENT(AMPERES) 1.6 1.2 0.8 0.4 0 80 90 100 110 120 130 140 150 RESISTIVE OR INDUCTIVE LOAD P.C.B. 0.2X0.2"(5.0X5.0mm) COPPER PAD AREAS FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 25 20 15 10 5 0 1 10 8.3ms SINGLE HALF SINE WAVE (JEDEC Method) at TL=110℃ 100 LEAD TEMPERATURE (℃) NUMBER OF CYCLES AT 60Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT(AMPERES) 50 10 FIG.4-TYPICAL REVERSE CHARACTERISTICS 1000 INSTANTANEOUS REVERSE CURRENT ,(mA) 100 TJ=125℃ 1 10 0.1 TJ=25℃ PULSE WIDTH=300mS 1% DUTY CYCLE 1 TJ=75℃ 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0.1 TJ=25℃ INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) FIG.5-TYPICAL JUNCTION CAPACITANCE 14 JUNCTIOIN CAPACITANCE(pF) 12 10 8 6 4 2 0 0.1 1 10 100 REVERSE VOLTAGE. VOLTS TJ=25℃ f=1.0MHz Vsig=50mVp-P FIG.6-TYPICAL TRANSIENT THERMAL IMPEDANCE 100 TRANSIENT THERMAL IMPEDANCE, ℃/W MOUNTED ON 0.2X0.2"(5X7mm) COPPER PAD AREAS 10 1 0.1 1 10 100 T, PULSE DURATION ,sec.