FR106G

FR101G THRU FR107G Features · Fast switching · Low leakage · Low forward voltage drop · High current capability · Glass passivated junction · High reliability capability CURRENT 1.0 Ampere VOLTAGE 50 to 1000 Volts DO-41 0.107(2.7) 0.080(2.0) DIA. 1.0(25.4) MIN. 0.205(5.2) 0.166(4.2) Mechanical Data · Case : JEDEC DO-41 molded plastic body · Terminals : Plated axial lead solderable per MIL-STD-750, method 2026 · Polarity : Color band denotes cathode end · Mounting Position : Any · Weight : 0.012 ounce, 0.33 gram 1.0(25.4) MIN. 0.034(0.9) 0.028(0.7) DIA. Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current 0.375"(9.5mm) lead length TA=55℃ Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum instantaneous forward voltage at 1.0A Maximum DC reverse current at rated DC blocking voltage Maximum full load reverse current full cycle average. 0.375"(9.5mm) lead length at TL=55℃ Maximum reverse recovery time (Note 1) Typical junction capacitance (Note 2) Operating junction and storage temperature range IR VRRM VRMS VDC I(AV) IFSM VF FR 101G 50 35 50 FR 102G 100 70 100 FR 103G 200 140 200 FR 104G 400 280 400 1.0 30.0 1.3 5.0 FR 105G 600 420 600 FR 106G 800 560 800 FR 107G 1000 700 1000 Units Volts Volts Volts Amp Amps Volts μA 100 Trr CJ TJ TSTG 150 15.0 -65 to +175 250 500 ns pF ℃ Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. RATINGS AND CHARACTERISTIC CURVES FR101G THRU FR107G FIG.1-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50W NON INDUCTIVE 10W NON INDUCTIVE +0.5A Trr (+) 25Vdc (APPROX) D.U.T. PULSE GENERATOR (NOTE2) 0 -0.25A ( ) NON INDUCTIVE 1W OSCILLOSCOPE (NOTE1) -1.0A 1cm NOTES : 1.Rise Time=7ns max. input impedance=1 megohm 22pF 2.Rise Time=10ns max. source impedance =50 ohms SET TIME BASE FOR 50/100 ns/cm FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE FIG.3-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT(AMPERES) 50 8.3m SINGLE HALF SINE WAVE (JEDEC Method) 1.50 AVERAGE FORWARD CURRENT(A) 1.25 1.00 0.75 0.50 0.25 0 0 25 50 75 100 125 150 175 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 40 30 20 10 AMBIENT TEMPERATURE ( ℃) 0 1 2 4 6 8 10 20 40 60 100 NUMBER OF CYCLES AT 60Hz FIG.4-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.5-TYPICAL JUNCTION CAPACITANCE 10 INSTANTANEOUS FORWARD CURRENT(AMPERES) JUNCTION CAPACITANCE(pF) 200 100 60 40 20 10 6 4 2 TJ=25℃ 3 1 0.3 0.1 TJ=25℃ 1 0.03 0.01 0.4 0.6 0.8 Pulse Width=300mS 1% Duty Cycle 0.1 0.2 0.4 1 2 4 10 20 40 100 REVERSE VOLTAGE. (V) 1.4 1.6 1.0 1.2 INSTANTANEOUS FORWARD VOLTAGE (VOLTS)