FR1606

FR1601 THRU FR1607 Features · Fast switching · Low leakage · Low forward voltage drop · High current capability · High current surge · High reliability CURRENT 16.0 Amperes VOLTAGE 50 to 1000 Volts TO-220 .412 (10.5) MAX. .180 3.8 +.2 HOLE THRU (4.6) .248 (6.3) .595 (15.1) MAX. .050 (1.27) .108 (2.75) Mechanical Data · Case : JEDEC TO-220 molded plastic body · Terminals : Lead solderable per MIL-STD-750, method 2026 · Polarity : As marked · Mounting Position : Any · Weight : 0.08 ounce, 2.24 gram .051 MAX. (1.3) .040 MAX. (1.0) .100 (2.54) PIN 1 PIN 3 Positive CT Suffix "C" .550 .158 (14.0) (4.0) MIN. MAX. .120 (3.05) + CASE PIN 2 PIN 1 PIN 3 Negative CT Suffix "A" CASE PIN 2 Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current See Fig. 2 Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum instantaneous forward voltage at 8.0A Maximum DC reverse current at rated DC blocking voltage TC=25℃ TC=125℃ VRRM VRMS VDC I(AV) IFSM VF IR Trr FR 1601 50 35 50 FR 1602 100 70 100 FR 1603 200 140 200 FR 1604 400 280 400 16.0 150 1.3 10 100 FR 1605 600 420 600 FR 1606 800 560 800 FR 1607 1000 700 1000 Units Volts Volts Volts Amps Amps Volts μA 250 500 ns ℃/W ℃ Maximum reverse recovery time (Note 1) Typical thermal resistance (Note 2) Operating junction and storage temperature range 150 3.0 -55 to +150 RθJC TJ TSTG Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (3) Thermal resistance from junction to case mounted on heatsink. RATINGS AND CHARACTERISTIC CURVES FR1601 THRU FR1607 FIG . 1-REVERSE RECOVERY TIMECHARACTERISTIC AND TESTCIRCUIT DIAGRAM 50 10 trr NONINDUCTIVE NONINDUCTIVE +0.5A (+ ) 50Vdc (approx) (-) DUT PULSE GENERATOR ( NOTE 2 ) 0 -0.25A NONINDUCTIVE OSCILLOSCOPE (NOTE 1 ) NOTES: 1 . RISE TIM E = 7nsmax. INPUT IMPEDANCE= 1 MEGOHM 22pf 2 . RISE IM E = 10ns max. SOURSE T IMPEDANCE = 50ohmsf -1.0A 1cm SET TIME BASE FOR 5/ 10ns / cm AV E R A G E F O R WA R D C U R R E N T ( A ) 20.0 16.0 12.0 8.0 4.0 0 F IG . 2- MAXIMUM F ORWARD CURRENT D ERATING CURVE 1 000 I N S TA N TA N E O U S R E V E R S E C U R R E N T . ( A ) FIG . 3 - T YPICAL REVERSE CHARACTERISTICS 100 Tj=125 C O 10 Tj=25 C O 0 50 100 O LEAD TEMPERATURE . ( C ) 150 300 P E A K F O R WA R D S U R G E CURRENT . ( A ) 250 200 150 100 FIG .4 - MAXIMUM N ON - REPETITIVE FORWARD S URGE CURRENT 1.0 8.3ms Single Half Sine Wave JEDEC Method 0.1 0 PERCENT OF RATED P EAK REVERSE V OLTAGE. ( % ) 20 40 60 80 100 120 140 1 2 5 10 20 NUMBER OF CYCLES A T 60Hz 50 1 00 I N S TA N TA N E O U S F O R WA R D V O LTA G E . ( A ) 50 80 40 20 FIG . 6 - T YPICAL INSTANTANEOUS F ORWARD CARACTERISTICS 10 4 2 1.0 .4 .2 .1 .8 .9 1.0 1.1 1 .2 1.3 1.4 1.5 Pulse Width=300 1% Duty Cycle 1 20 C A PA C I TA N C E . ( p F ) 100 80 60 40 20 FIG .5 - TYPICAL J UNCTION CAPACITANCE PER LEG Tj=25 C O s Tj=25 C f = 1.0MHz Vsig = 50mVp-p O 0 .1 0.5 1.0 5 10 50 100 500 1 000 REVERSE VOLTAGE . ( V ) INSTANTANEOUS F ORWARD VOLTAGE . ( A )