FR206G

FR201G THRU FR207G Features · Fast switching · Low leakage · Low forward voltage drop · High current capability · Glass passivated junction · High switching capability CURRENT 2.0 Amperes VOLTAGE 50 to 1000 Volts DO-15 0.140(3.6) 0.104(2.6) DIA. 1.0(25.4) MIN. 0.300(7.6) 0.230(5.8) Mechanical Data · Case : JEDEC DO-15 molded plastic body · Terminals : Plated axial lead solderable per MIL-STD-750, method 2026 · Polarity : Color band denotes cathode end · Mounting Position : Any · Weight : 0.014 ounce, 0.39 gram 0.034(0.9) 0.028(0.7) DIA. 1.0(25.4) MIN. Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current 0.375"(9.5mm) lead length TA=55℃ Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum instantaneous forward voltage at 2.0A Maximum DC reverse current at rated DC blocking voltage Maximum full load reverse current full cycle average. 0.375"(9.5mm) lead length at TL=55℃ Maximum reverse recovery time (Note 1) Typical junction capacitance (Note 2) Operating junction and storage temperature range IR VRRM VRMS VDC I(AV) IFSM VF FR 201G 50 35 50 FR 202G 100 70 100 FR 203G 200 140 200 FR 204G 400 280 400 2.0 60 1.3 5.0 FR 205G 600 420 600 FR 206G 800 560 800 FR 207G 1000 700 1000 Units Volts Volts Volts Amps Amps Volts μA 100 Trr CJ TJ TSTG 150 35 -65 to +175 250 500 ns pF ℃ Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. RATINGS AND CHARACTERISTIC CURVES FR201G THRU FR207G FIG.1-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50W NON INDUCTIVE 10W NON INDUCTIVE +0.5A Trr (+) 25Vdc (APPROX) D.U.T. PULSE GENERATOR (NOTE2) 0 -0.25A ( ) NON INDUCTIVE 1W OSCILLOSCOPE (NOTE1) -1.0A 1cm NOTES : 1.Rise Time=7ns max. input impedance=1 megohm 22pF 2.Rise Time=10ns max. source impedance =50 ohms SET TIME BASE FOR 50/100 ns/cm FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE FIG.3-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT(AMPERES) 60 50 40 30 20 10 0 1 2 4 6 8 10 20 40 60 100 NUMBER OF CYCLES AT 60Hz 8.3m SINGLE HALF SINE WAVE (JEDEC Method) AVERAGE FORWARD CURRENT(A) SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 2.00 1.50 1.00 0.50 0 0 25 50 75 100 125 150 175 AMBIENT TEMPERATURE ( ℃) FIG.4-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.5-TYPICAL JUNCTION CAPACITANCE 10 INSTANTANEOUS FORWARD CURRENT(AMPERES) JUNCTION CAPACITANCE(pF) 200 100 60 40 20 10 6 4 2 TJ=25℃ Pulse Width=300mS 1% Duty Cycle 1 TJ=25℃ 0.1 1 0.1 0.2 0.4 1 2 4 10 20 40 100 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 REVERSE VOLTAGE. (V) INSTANTANEOUS FORWARD VOLTAGE (VOLTS)