FR805

FR801 THRU FR807 Features · Fast switching · Low leakage · Low forward voltage drop · High current capability · High current surge · High reliability CURRENT 8.0 Amperes VOLTAGE 50 to 1000 Volts TO-220A .412 (10.5) MAX. .180 3.8 f +.2 HOLE THRU (4.6) .248 (6.3) .595 (15.1) MAX. .550 .158 (14.0) (4.0) MIN. MAX. .200 (5.08) + .108 (2.75) .040 (1.0) MAX. .051 MAX. (1.3) .040 MAX. (1.0) .050 (1.27) Mechanical Data · Case : JEDEC TO-220A molded plastic body · Terminals : Lead solderable per MIL-STD-750, method 2026 · Polarity : As marked · Mounting Position : Any · Weight : 0.08 ounce, 2.24 gram PIN 1 + CASE PIN 2 Case Positive + CASE PIN 2 Case Negative Suffix "R" PIN 1 .120 (3.05) Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TC=55℃ Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum instantaneous forward voltage at 8.0A Maximum DC reverse current at rated DC blocking voltage TC=25℃ TC=125℃ VRRM VRMS VDC I(AV) IFSM VF IR Trr CJ FR 801 50 35 50 FR 802 100 70 100 FR 803 200 140 200 FR 804 400 280 400 8.0 150 1.3 10 100 FR 805 600 420 600 FR 806 800 560 800 FR 807 1000 700 1000 Units Volts Volts Volts Amps Amps Volts μA 250 500 ns pF ℃/W ℃ Maximum reverse recovery time (Note 1) Typical junction capacitance (Note 2) TJ=25℃ Typical thermal resistance (Note 3) Operating junction and storage temperature range 150 60 3.0 -55 to +150 RθJC TJ TSTG Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. (3) Thermal resistance from junction to case, single side cooled. RATINGS AND CHARACTERISTIC CURVES FR801 THRU FR807 FIG . 1 -REVERSE RECOVERY TIME CHARACTERISTIC NONINDUCTIVE AND TEST CIRCUIT DIAGRAM 50 NONINDUCTIVE +0.5A 10 trr (+ ) 50Vdc (approx) (-) DUT OSCILLOSCOPE (NOTE 1 ) PULSE GENERATOR ( NOTE 2 ) 0 -0.25A NONINDUCTIVE NOTES: 1 . RISE TIM E = 7nsmax. INPUT IMPEDANCE= 1 MEGOHM 22pf 2 . RISE IM E = 10ns max. SOURSE T IMPEDANCE = 50ohmsf -1.0A 1cm SET TIME BASE FOR 5/ 10ns / cm AV E R A G E F O R WA R D C U R R E N T ( A ) FIG . 2- MAXIMUM F ORWARD CURRENT D ERATING CURVE 10 I N S TA N TA N E O U S F O R WA R D V O LTA G E . ( A ) 8 6 4 2 0 0 50 100 LEAD TEMPERATURE . (OC ) 150 FIG . 5 - T YPICAL INSTANTANEOUS F ORWARD CARACTERISTICS 4 00 200 100 40 20 10 4 2 1 0.4 0.2 0.1 .6 .8 1.0 1.2 1 .4 1.6 1.8 2.0 I NSTANTANEOUS F ORWARD VOLTAGE . ( A ) FIG . 6 - T YPICAL REVERSE CHARACTERISTICS Tj=125 C O Pulse Width=300 1% Duty Cycle Tj=25OC s P E A K F O R WA R D S U R G E CURRENT . ( A ) 1 50 125 100 75 50 FIG . 3 - M AXIMUM NON - REPETITIVE F ORWARD S URGE CURRENT 8.3ms Single Half Sine Wave JEDEC Method TC = 125OC I N S TA N TA N E O U S R E V E R S E C U R R E N T . ( A ) 25 1 2 5 10 20 NUMBER OF CYCLES A T 60Hz 50 1 00 1 00 40 10 4 2 1.0 .4 .2 FIG . 4 - T YPICAL HUNCTION CAPACITANCE 1 20 C A PA C I TA N C E . ( p F ) 100 80 60 40 20 0.1 Tj=25 C f = 1.0MHz Vsig = 50mVp-p O Tj=75OC Tj=25OC 20 40 60 8 0 100 120 140 PERCENT OF RATED PEAK REVERSE V OLTAGE. ( % ) 0.5 1.0 5 10 50 100 REVERSE VOLTAGE . ( V ) 500 1 000 .1 0