HER1605

HER1601 THRU HER1606 Features · Plastic package has Underwriters Laboratory Flammability Classification 94V-0 · Low forward voltage drop · High current capability · High reliability · Low power loss, high effciency · High surge current capability · High speed switching · Low leakage CURRENT 16.0 Amperes VOLTAGE 50 to 600 Volts TO-220A .412 (10.5) MAX. .180 3.8 f +.2 HOLE THRU (4.6) .248 (6.3) .595 (15.1) MAX. .550 .158 (14.0) (4.0) MIN. MAX. .200 (5.08) + .108 (2.75) .040 (1.0) MAX. .051 MAX. (1.3) .040 MAX. (1.0) .050 (1.27) Mechanical Data · Case : JEDEC TO-220A molded plastic body · Terminals : Lead solderable per MIL-STD-750, method 2026 · Polarity : As marked · Mounting Position : Any · Weight : 0.08 ounce, 2.24 gram PIN 1 + CASE PIN 2 Case Positive + CASE PIN 2 Case Negative Suffix "R" PIN 1 .120 (3.05) Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current 0.375"(9.5mm) lead length @ at TA=100℃ Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum instantaneous forward voltage at 8.0A Maximum DC reverse current at rated DC blocking voltage TA=25℃ Maximum DC reverse current at rated DC blocking voltage TA=125℃ Maximum reverse recovery time (Note 1) Typical junction capacitance (Note 2) Typical thermal resistance (Note 3) Operating junction and storage temperature range IR VRRM VRMS VDC I(AV) IFSM VF HER 1601 50 35 50 HER 1602 100 70 100 HER 1603 200 140 200 HER 1604 300 210 300 16.0 200 HER 1605 400 280 400 HER 1606 600 420 600 Units Volts Volts Volts Amps Amps 1.0 10.0 1.3 1.7 Volts μA 100 Trr CJ 50 80 2.2 -55 to +150 -55 to +150 80 50 ns pF ℃/W ℃ RθJC TJ TSTG Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. (3) Thermal resistance from junction to case mounting on heatsink. RATINGS AND CHARACTERISTIC CURVES HER1601 THRU HER1606 FIG . 1 -REVERSE RECOVERY TIME CHARACTERISTIC NONINDUCTIVE 50 NONINDUCTIVE 10 AND TEST CIRCUIT DIAGRAM trr +0.5A PULSE GENERATOR ( NOTE 2 ) 0 -0.25A DUT (+ ) 50Vdc (approx) (-) NONINDUCTIVE OSCILLOSCOPE (NOTE 2 ) -1.0A 1cm SET TIME BASE FOR 5/ 10ns / cm NOTES: 1 . RISE TIM E = 7nsmax. INPUT IMPEDANCE= 1 MEGOHM 22p 2 . RISE IM E = 10ns max. SOURSE T IMPEDANCE = 50ohmsf AV E R AG E F O R WAR D C U R R E N T . ( A ) . FIG 2 -MAXIMUM AVERAGE FORWARD CURRENT DERATING 20 16 12 8 4 0 0 50 100 CASE TEMPERATURE . ( % ) 150 A) 1000 FIG . 3 -TYPICAL REVERSE CHARACTERISTICS I N S TA N TA N E O U S R E V E R S E C U R R E T . ( 100 Tj=125 C O 10 Tj=25 C O PE A K F O R W A R D S U R G E C U R R E N T . ( A ) FIG . 4 -MAXIMUM NON - REPETITIVE FORWARD SURGE CURRENT 120 90 60 1 Tj=25oC 8.3ms Single Half Sine Wave JEDEC Method 0.1 PERCENT OF RATED PEAK REVERSE VOLT AGE . (%) 20 40 60 80 100 120 140 I N S TA N TA N E O U S F O R WA R D C U R R E N T . ( A ) 30 1 2 5 10 20 NMBER OF CYCLES AT 60Hz 50 1 00 FIG . 6 -TYPICAL FRWARD CHARACTERISTICS 100 30 60 1-1 240 C A PA C I TA N C E ( p F ) 200 160 120 80 40 0 FIG . 5 -TYPICAL JUNCTIOON CAP ACITANCE PER LEG 1.0 0.3 0.1 0.03 .010.4 HE R1 3.0 60 HE HE R1 60 R1 Tj=25oC Pulse Width=300 1% Duty Cycle 6 Tj=25 C o HE HE R1 60 6 R1 60 1-1 60 5 60 10 4 5 s 1.8 0.6 0.8 1.0 1 .2 1.4 1.6 1 2 5 10 20 50 100 200 REVERSE VOLTAGE . ( V) 500 1000 FORWARD VOLTAGE . ( V )