HER602

HER601 THRU HER608 Features · Plastic package has Underwriters Laboratory Flammability Classification 94V-0 · Low forward voltage drop · High current capability · High reliability · Low power loss, high effciency · High surge current capability · High speed switching · Low leakage CURRENT 6.0 Amperes VOLTAGE 50 to 1000 Volts P-6 0.360(9.1) 0.340(8.6) DIA. 1.0(25.4) MIN. Mechanical Data · Case : P-6 molded plastic body · Epoxy : UL94V-0 rate flame retardant · Lead : Plated axial lead solderable per MIL-STD-750, method 2026 · Polarity : Color band denotes cathode end · Mounting Position : Any · Weight : 0.074 ounce, 2.1 gram 0.360(9.1) 0.340(8.6) 0.052(1.3) 0.048(1.2) DIA. 1.0(25.4) MIN. Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current 0.375"(9.5mm) lead length @ at TA=55℃ Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum instantaneous forward voltage at 2.0A Maximum DC reverse current at rated DC blocking voltage TA=25℃ Maximum DC reverse current at rated DC blocking voltage TA=100℃ Maximum reverse recovery time (Note 1) Typical junction capacitance (Note 2) Operating junction and storage temperature range IR VRRM VRMS VDC I(AV) IFSM VF HER 601 50 35 50 HER 602 100 70 100 HER 603 200 140 200 HER 604 300 210 300 HER 605 400 280 400 6.0 HER 606 600 420 600 HER 607 800 560 800 HER 608 1000 700 1000 Units Volts Volts Volts Amps Amps 200.0 1.0 1.3 10.0 1.7 Volts μA 200 Trr CJ TJ TSTG 50 100 -65 to +125 -65 to +150 75 65 ns pF ℃ Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. RATINGS AND CHARACTERISTIC CURVES HER601 THRU HER608 FIG.1-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50W NON INDUCTIVE 10W NON INDUCTIVE FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE Trr +0.5A AVERAGE FORWARD CURRENT(A) 6.0 5.0 4.0 3.0 2.0 1.0 0 0 25 50 75 100 125 150 175 AMBIENT TEMPERATURE ( ℃) SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 0.375"(9.5mm) LEAD LENGTH (+) 25Vdc (APPROX) ( ) D.U.T. PULSE GENERATOR (NOTE2) OSCILLOSCOPE (NOTE1) 0 -0.25A 1W NON INDUCTIVE NOTES : 1.Rise Time=7ns max. input impedance=1 megohm 22pF 2.Rise Time=10ns max. source impedance = 50 ohms -1.0A 1cm SET TIME BASE FOR 20/30 ns/cm FIG.3-TYPICAL FORWARD CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT(AMPERES) 100 FIG.4-TYPICAL REVERSE CHARACTERISTICS 1000 INSTANTANEOUS REVERSE CURRENT (mA) TA=100℃ 10 60 4 R6 01 H HE R6 05 H ER 60 6 100 ER 8 HE HE R6 1 07 -H ER 10 TA=25℃ 60 1.0 0.1 TA=25℃ PULSE WIDTH=300mS 1% DUTY CYCLE 0.1 1.8 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) INSTANTANEOUS FORWARD VOLTAGE (VOLTS) FIG.5-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 350 300 PEAK FORWARD SURGE CURRENT(AMPERES) 250 200 150 100 50 0 1 5 10 NUMBER OF CYCLES AT 60Hz 50 100 FIG6-TYPICAL JUNCTION CAPACITANCE 175 JUNCTION CAPACITANCE(pF) TA=25℃ 8.3m SINGLE HALF SINE WAVE (JEDEC Method) 150 125 100 75 50 25 0 0.1 0.5 1 2 5 10 20 50 100 200 1000 REVERSE VOLTAGE. (V) HER607-HER608 HER601-HER606 TJ=25℃