UF4003

UF4001 THRU UF4007 Features · Plastic package has Underwriters Laboratory Flammability Classification 94V-0 · Low forward voltage drop · High current capability · High reliability · Low power loss, high effciency · High surge current capability · High speed switching · Low leakage CURRENT 1.0 Ampere VOLTAGE 50 to 1000 Volts DO-41 0.107(2.7) 0.080(2.0) DIA. 1.0(25.4) MIN. Mechanical Data · Case : JEDEC DO-41 molded plastic body · Epoxy : UL94V-0 rate flame retardant · Lead : Plated axial lead solderable per MIL-STD-750, method 2026 · Polarity : Color band denotes cathode end · Mounting Position : Any · Weight : 0.012 ounce, 0.33 gram 0.205(5.2) 0.166(4.2) 0.034(0.9) 0.028(0.7) DIA. 1.0(25.4) MIN. Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current 0.375"(9.5mm) lead length at TA=50℃ Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum instantaneous forward voltage at 1.0A Maximum DC reverse current at rated DC blocking voltage Maximum full load reverse current full cycle average. 0.375"(9.5mm) lead length at TL=55℃ Maximum reverse recovery time (Note 1) Typical junction capacitance (Note 2) Operating junction and storage temperature range IR VRRM VRMS VDC I(AV) IFSM VF UF 4001 50 35 50 UF 4002 100 70 100 UF 4003 200 140 200 UF 4004 400 280 400 1.0 30.0 UF 4005 600 420 600 UF 4006 800 560 800 UF 4007 1000 700 1000 Units Volts Volts Volts Amp Amps 1.0 1.3 5.0 1.7 Volts μA 100 Trr CJ TJ TSTG 50 20 -65 to +150 75 10 ns pF ℃ Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. RATINGS AND CHARACTERISTIC CURVES UF4001 THRU UF4007 FIG.1-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50W NON INDUCTIVE 10W NON INDUCTIVE FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE Trr AVERAGE FORWARD CURRENT (A) 1.0 0.8 0.6 0.4 0.2 0 0 25 50 75 100 125 150 175 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD +0.5A (+) 25Vdc (APPROX) ( ) D.U.T. PULSE GENERATOR (NOTE2) OSCILLOSCOPE (NOTE1) 0 -0.25A 1W NON INDUCTIVE NOTES : 1.Rise Time=7ns max. input impedance=1 megohm 22pF 2.Rise Time=10ns max. source impedance = 50 ohms -1.0A 1cm SET TIME BASE FOR 50/100 ns/cm AMBIENT TEMPERATURE (℃) FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT (AMPERES) 10 FIG.4-TYPICAL REVERSE CHARACTERISTICS 100 INSTANTANEOUS REVERSE CURRENT ,(mA) 50\100\200\400V 1.0 10 TJ=150℃ TJ=100℃ 1.0 TJ=25℃ 0.1 600\800\1000V 0.1 0.01 TJ=25℃ PULSE WIDTH=300mS 1% DUTY CYCLE 0.01 0 20 40 60 80 100 120 140 1.8 0.001 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) INSTANTANEOUS FORWARD VOLTAGE (VOLTS) FIG.5-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 50 40 30 20 10 0 1 5 10 NUMBER OF CYCLES AT 60Hz 50 100 FIG6-TYPICAL JUNCTION CAPACITANCE 200 100 JUNCTION CAPACITANCE (pF) 60 40 20 10 6 4 TJ=25℃ UF4005-UF4007 UF4001-UF4004 8.3m SINGLE HALF SINE WAVE (JEDEC Method) PEAK FORWARD SURGE CURRENT (AMPERES) 2 1 0.1 0.2 0.4 1 2 4 10 20 40 100 REVERSE VOLTAGE. (V)