19-6039; Rev 2; 4/12
78M6631
3-Phase PowerMeasurement IC
LE
AVAILAB
DATA SHEET
DS_6631_056
DESCRIPTION
FEATURES
The Teridian™ 78M6631 is a highly integrated 3-phase
power measurement and monitoring system-on-chip
(SoC), with a 10 MHz 8051-compatible MPU core and
Single Converter Technology® containing a 22-bit deltasigma converter and 32-bit compute engine (CE). The
78M6631 has been designed specifically for a wide
variety of applications requiring 3-phase power and
quality measurements. It supports both Delta and Wye
configurations.
< 0.5% Watt Accuracy Over 2000:1 Current
Range and Over Temperature
Exceeds IEC 62053/ANSI C12.20 Standards
Voltage Reference < 40 ppm/°C
Six Analog Inputs Supporting 3-Phase Voltage
and Current Measurement Inputs
Pin- or Biselectable Delta or Wye Configuration
22-Bit Delta-Sigma ADC with Independent 32Bit Compute Engine (CE)
8-Bit MPU (80515), One Clock Cycle per
Instruction with 4 KB MPU XRAM
128 KB Flash with Security
32 kHz Time Base with Hardware Watchdog
Timer
UART, I2C, and High-Speed Slave SPI Host
Interface Options
17 General-Purpose 5 V Tolerant I/O Pins
Packaged in a RoHS-Compliant (6/6)
Lead(Pb)-Free 56-Pin TQFN
Application Firmware Includes (per Phase):
o True RMS Current and Voltage Calculations
o Active, Reactive, Apparent, Fundamental,
and Harmonic Power Calculations
o Fundamental and Harmonic Current and
Voltage Calculations
o Line Frequency and Power Factor
Calculations
o Phase Compensation (18 at 60 Hz)
o Built-In Calibration Routines
o Programmable Alarm Thresholds
o Command Line (UART) Communications
o High-Speed SPI Communications
At the measurement interface, the device provides six
analog inputs including three differential current and three
voltage for interfacing to current and voltage sensors. The
device provides better than 0.5% accuracy over a wide
2000:1 dynamic range.
The integrated MPU core and 128 KB of flash memory
provide a flexible means of configuration, postprocessing, data formatting, interfacing to host processor
via a UART or SPI interface, or using DIO pins for LEDs
or relay control. Complete firmware is available from
Maxim and can be loaded into the IC during
manufacturing test.
Functional Diagrams
Pin Configurations appear at end of data sheet.
Functional Diagrams continued at end of data sheet.
UCSP is a trademark of Maxim Integrated Products, Inc.
Teridian is a trademark and Single Converter Technology is a registered trademark of Maxim Integrated Products, Inc.
For pricing, delivery, and ordering information, please contact Maxim Direct
at 1-888-629-4642, or visit Maxim’s website at www.maximintegrated.com.
78M6631 Data Sheet
DS_6631_056
Table of Contents
1
Hardware Functional Description...................................................................................................... 5
1.1 Hardware Overview ..................................................................................................................... 5
1.2 Device Reset................................................................................................................................ 7
1.3 Power Management..................................................................................................................... 7
1.3.1 Voltage Regulator ............................................................................................................ 7
1.3.2 Power Fault Management................................................................................................ 7
1.4 Analog Front-End (AFE) .............................................................................................................. 8
1.4.1 Analog Current and Voltage Inputs ................................................................................. 8
1.5 Digital Computation Engine (CE)................................................................................................. 9
1.6 80515 MPU Core ....................................................................................................................... 10
1.6.1 SFRs .............................................................................................................................. 10
1.7 RAM ........................................................................................................................................... 10
1.8 IORAM ....................................................................................................................................... 10
1.9 Flash .......................................................................................................................................... 10
1.9.1 Program Security ........................................................................................................... 10
1.10 Oscillator .................................................................................................................................... 11
1.11 PLL and Internal Clock Generation............................................................................................ 11
1.12 Real-Time Clock (RTC).............................................................................................................. 11
1.13 Hardware Watchdog Timer ........................................................................................................ 11
1.14 Temperature Sensor .................................................................................................................. 12
1.15 General Purpose Digital I/O ....................................................................................................... 12
1.16 D/Y Selection Pin ....................................................................................................................... 12
1.17 EEPROM Interface .................................................................................................................... 12
1.18 SPI Slave Port............................................................................................................................ 12
1.19 Test Port..................................................................................................................................... 13
1.20 UART ......................................................................................................................................... 13
1.21 In Circuit Emulator (ICE) Port .................................................................................................... 14
2
Electrical Specifications................................................................................................................... 15
2.1 Absolute Maximum Ratings ....................................................................................................... 15
2.2 Recommended External Components....................................................................................... 16
2.3 Recommended Operating Conditions........................................................................................ 16
2.4 Performance Specifications ....................................................................................................... 17
2.4.1 Input Logic Levels.......................................................................................................... 17
2.4.2 Output Logic Levels ....................................................................................................... 17
2.4.3 Power-Fault Comparator ............................................................................................... 17
2.4.4 Power Supply Monitor.................................................................................................... 18
2.4.5 Supply Current ............................................................................................................... 18
2.4.6 Crystal Oscillator............................................................................................................ 18
2.4.7 Temperature Sensor...................................................................................................... 19
2.4.8 VREF ............................................................................................................................. 19
2.4.9 ADC Converter, V3P3A Referenced ............................................................................. 20
2.5 Timing Specifications ................................................................................................................. 21
2.5.1 Flash Memory ................................................................................................................ 21
2.5.2 EEPROM Interface ........................................................................................................ 21
2.5.3 RESET ........................................................................................................................... 21
2.5.4 SPI Slave Port................................................................................................................ 22
3
Packaging .......................................................................................................................................... 23
3.1 56-Pin QFN Package ................................................................................................................. 23
3.2 Pinout ......................................................................................................................................... 23
3.2.1 56-Pin QFN Package Outline ........................................................................................ 24
3.2.2 Recommended PCB Land Pattern for the QFN-56 Package ........................................ 25
4
Pin Descriptions................................................................................................................................ 26
2
Rev 2
DS_6631_056
4.1
4.2
4.3
78M6631 Data Sheet
Power and Ground Pins............................................................................................................. 26
Analog Pins................................................................................................................................ 26
Digital Pins ................................................................................................................................. 27
5
I/O Equivalent Circuits...................................................................................................................... 28
6
Ordering Information ........................................................................................................................ 29
7
Contact Information.......................................................................................................................... 29
Revision History........................................................................................................................................ 30
Rev 2
3
78M6631 Data Sheet
DS_6631_056
Figures
Figure 1: 78M6631 IC Functional Block Diagram ......................................................................................... 6
Figure 2: AFE Block Diagram ....................................................................................................................... 8
Figure 3: Functions Defined by V1.............................................................................................................. 11
Figure 4: SPI Slave Port: Typical Read and Write Operations ................................................................... 13
Figure 5: SPI Slave Port Timing.................................................................................................................. 22
Figure 6: Pinout for QFN-56 Package......................................................................................................... 23
Figure 7: PCB Land Pattern for QFN-56 Package...................................................................................... 25
Figure 8: I/O Equivalent Circuits ................................................................................................................. 28
Tables
Table 1: SPI Command Description............................................................................................................ 13
Table 2: Absolute Maximum Ratings .......................................................................................................... 15
Table 3: Recommended External Components .......................................................................................... 16
Table 4: Recommended Operating Conditions........................................................................................... 16
Table 5: Input Logic Levels ......................................................................................................................... 17
Table 6: Output Logic Levels ...................................................................................................................... 17
Table 7: Power-Fault Comparator Performance Specifications.................................................................. 17
Table 8: Power Supply Monitor Performance Specifications (BME= 1)...................................................... 18
Table 9: Supply Current Performance Specifications ................................................................................. 18
Table 10: Crystal Oscillator Performance Specifications............................................................................ 18
Table 11: Temperature Sensor Performance Specifications ...................................................................... 19
Table 12: VREF Performance Specifications.............................................................................................. 19
Table 13: ADC Converter Performance Specifications............................................................................... 20
Table 14: Flash Memory Timing Specifications .......................................................................................... 21
Table 15: EEPROM Interface Timing.......................................................................................................... 21
Table 16: RESET Timing ............................................................................................................................ 21
Table 17: SPI Slave Port Timing................................................................................................................. 22
Table 19: Power and Ground Pins.............................................................................................................. 26
Table 20: Analog Pins ................................................................................................................................. 26
Table 21: Digital Pins .................................................................................................................................. 27
Table 22: Ordering Information ................................................................................................................... 29
4
Rev 2
DS_6631_056
78M6631 Data Sheet
1 Hardware Functional Description
1.1
Hardware Overview
The Teridian 78M6631 single-chip power measurement and monitoring device integrates all the primary
AC measurement and control blocks required to implement the 3-phase power measurement and
monitoring system.
The 78M6631 includes:
Six input analog front-end (AFE) (3 Differential Current/3 Voltage)
Independent digital computation engine (CE)
8051-compatible microprocessor (MPU) which executes one instruction per clock cycle (80515)
Precision voltage reference
Temperature sensor
RAM and flash memory
A variety of I/O pins
Communication Interfaces: UART, SPI, and I2C (Master)
Various current sensor technologies are supported including Current Transformers (CT), Resistive
Shunts, and Rogowski coils.
The 32-bit compute engine (CE) of the 78M6631 sequentially process the samples from the analog inputs
on pins IA, IB, IC, VA, VB, and VC and performs calculations to measure active power (Watts), reactive
power (VARs), apparent power (VAs), power factor, fundamental power, and harmonic power for three
independent phases. RMS, fundamental, and harmonic currents and voltages are also computed for each
phase. Totals are available for most results.
Figure 1 provides a block diagram of the 78M6631 IC. A detailed description of the various functional
blocks follows.
Refer to the applicable Firmware Description Document for additional supported functionality.
Rev 2
5
78M6631 Data Sheet
DS_6631_056
VREF
V3P3A
GNDA
V3P3SYS
IAP
ADC
CONVERTER
IAN
VBIAS
IBP
IBN
V3P3D
VBIAS
FIR
RTM
VBAT
VADC
ICP
ICN
to TMUX
VREF
VREF
VOLT
REG
RPULSE
CE
MUXP
WPULSE
VA
GNDD
XPULSE
VB
CE_ PROG
16
32
CE_ DATA
YPULSE
XPULSE
WPULSE
RPULSE
YPULSE
VC
V3P3D
TEMP
MCK
PLL
XIN
XOUT
80MHz
CK_CE
FLASH
128KB
2.5V to Logic
MULTIPURPOSE
IO
XRAM
4kB
DIO3
DIO4/SDCK
DIO5/SDATA
DIO6
DIO8
DIO9
D/Y
DIO11
CK_ MPU
OSC
(32. 768kHz)
CKTESTI
CKTEST
RTC
DIO17
CKTEST
TEST
MODE
DIO24
DIO25
SDATA
EEPROM /IF
SDCK
DIO29
DIO30
DIO45
DIO47
DIGITAL /IO
RX
DIO_4...
DIO51
DIO53
DIO55
UART
TX
XRAM BUS
8
SPI SLAVE
PCSZ
PCLK
PSDI
PSDO
PSDI
PCSZ
PSDO
PCLK
80515
MPU
E_ RST
E_ TCLK
E_ RXTX
SFR
EMULATOR
V1
POWER FAULT
E_ RXTX
E_ TCLK
E_ RSTZ
ICE_E
FAULTZ
TEST
MUX
RESET
TMUXOUT
ICE_E
Figure 1: 78M6631 IC Functional Block Diagram
6
Rev 2
DS_6631_056
1.2
78M6631 Data Sheet
Device Reset
When the RESET pin is pulled high, all digital activity stops. Only the oscillator and RTC module continue
to run. Additionally, all IORAM bits are set to their default states. As long as V1 (the input voltage at the
power fault block) is greater than VBIAS, the internal 2.5 V regulator continues to provide power to the
digital section.
Once initiated, the reset mode persists until the reset timer times out. This occurs in 4096 cycles of the
crystal clock after RESET goes low, at which time the MPU begins executing its preboot and boot
sequences from address 0x0000.
1.3
Power Management
1.3.1 Voltage Regulator
The 78M6631 provides an on-chip voltage regulator to create a 2.5 V supply for the digital logic. This
regulator can be run off of the V3P3SYS or VBAT inputs depending upon power availability.
1.3.2 Power Fault Management
The 78M6631 provides for both hardware and software controlled power fault management. The V1 pin is
connected to a comparator to monitor system power fault conditions. When the input to the comparator
falls (V1 < VBIAS) the device can enter a BROWNOUT mode, if supported in firmware and there is
sufficient voltage on VBAT, that reduces the MPU rate to 32 kHz and disables all the measurement frontend circuits. If the overhead on VBAT is insufficient to maintain a BROWNOUT mode, then the device can
also attempt to enter a SLEEP mode where only RTC functions are active.
If there is not sufficient voltage on VBAT (or it is not supported), then the part enters RESET mode when
the comparator fails.
Rev 2
7
78M6631 Data Sheet
1.4
DS_6631_056
Analog Front-End (AFE)
The AFE functions as a data acquisition system, controlled by the MPU. The main blocks in the AFE
consist of an input multiplexer, a delta-sigma A/D converter, a FIR decimation filter and a voltage
reference. The metrology input signals (IAP, IAN, IBP, IBN, ICP, ICN, VA, VB, VC, and TEMP) are
multiplexed before being sampled by the ADC. The ADC output is decimated by the FIR filter and the
results are stored in RAM where they can be accessed by the CE and the MPU.
The functionality of the AFE is established for various system requirements with different CE code. AFE
programmability includes, but is not limited to:
Input multiplexer settings
Voltage supply and temperature monitor inputs
ADC sampling rate
FIR length/resolution
Figure 2: AFE Block Diagram
1.4.1 Analog Current and Voltage Inputs
With all CE code implementations for the 78M6631, pins IAP, IAN, IBP, IBN, ICP, ICN, VA, VB, and VC
are analog inputs to the AFE for measuring current and voltage. Various current sensor technologies can
be supported including Current Transformers, Resistive Shunts, and Rogowski coils.
8
Rev 2
DS_6631_056
1.5
78M6631 Data Sheet
Digital Computation Engine (CE)
The CE, a dedicated 32-bit digital signal processor, performs the back-end computations. CE calculations
include:
Gain and offset compensation
Delay compensation on all channels
90 phase shift for VAR calculations
Frequency measurement
Accumulation for voltage and current RMS and power computation
Active, reactive, apparent, fundamental, and harmonic power calculation
Fundamental and harmonic current and voltage calculations
Monitoring of the input signal frequency (for frequency and phase information)
Monitoring of the input signal amplitude (for sag detection)
Temperature acquisition
Due to the custom nature and complexity of the CE, the CE code is part of the installed firmware and
is not modified by the user. Contact Maxim support for more information regarding CE code.
Rev 2
9
78M6631 Data Sheet
1.6
DS_6631_056
80515 MPU Core
The 78M6631 includes an 80515 MPU (8-bit, 8051-compatible) that processes most instructions in one
clock cycle. The 80515 architecture eliminates redundant bus states and implements parallel execution of
fetch and execution phases. Normally, a machine cycle is aligned with a memory fetch, therefore, most of
the 1-byte instructions are performed in a single machine cycle (MPU clock cycle). This leads to an 8x
average performance improvement (in terms of MIPS) over the Intel 8051 device running at the same clock
frequency.
1.6.1 SFRs
Several custom Special Function Registers (SFR) are implemented in the 78M6631’s 80515 MPU. Refer
to the 78M6631 Programmer’s Reference Manual for more information regarding the mapping of
functionality to specific SFR and IORAM addresses.
1.7
RAM
The CE and MPU share a single, general purpose 4KB RAM (also referred to as XRAM) for data. The
XRAM is natively accessible as 32-bit words from the CE and on 8-bit boundaries from the CPU. The
XRAM is accessed by the CPU through addresses 0x0000 to 0x0FFF.
1.8
IORAM
The MPU accesses most of its external input and output functionality as well as programmable
functionality through memory mapped IO (IORAM). The IORAM is accessed by the CPU as data
addresses 0x2000 to 0x20FF.
1.9
Flash
The 78M6631 includes 128 KB of on-chip flash memory. For read/write access from the CPU, the flash is
broken into four 32 KB banks that are managed by SFR settings. For erasing of the flash memory from
the CPU, the flash is segmented into individual 1024-byte pages and also controlled by SFR settings.
1.9.1 Program Security
The 78M6631 has functionality to guarantee the security of the user’s MPU and CE program code. When
enabled, the security feature limits the ICE to global flash erase operations only. All other ICE operations
are blocked. Security is enabled by MPU code that is executed in a pre-boot interval before the primary
boot sequence begins. Once security is enabled, the only way to disable it is to perform a global erase of
the flash, followed by a chip reset.
10
Rev 2
DS_6631_056
78M6631 Data Sheet
1.10 Oscillator
The 78M6631 oscillator drives a standard 32.768 kHz quartz crystal. These crystals are accurate and do
not require a high-current oscillator circuit. The 78M6631 oscillator has been designed specifically to
handle these crystals and is compatible with their high impedance and limited power handling capability.
The oscillator is powered directly and only from V3P3D, which therefore must be connected to a DC
voltage source not to exceed 4 V.
Since the oscillator is self-biasing, an external resistor must not be connected across the crystal.
1.11 PLL and Internal Clock Generation
Timing for the device is derived from the 32.768 kHz crystal oscillator output. The PLL and on-chip timing
functions provide several clocks which include:
The MPU clock (CKMPU)
The emulator clock (2 x CKMPU)
The clock for the CE (CKCE)
The delta-sigma ADC and FIR clock(CKADC, CKFIR)
These internal clocks can be adjusted for various programmable rates which affect device functionality.
Refer to the 78M6631 Programmer’s Reference Manual for more information regarding the
programmability of the 78M6631 PLL and internal clock generation modules.
1.12 Real-Time Clock (RTC)
The RTC circuit is driven directly by the crystal oscillator. The RTC consists of a counter chain and output
registers. The counter chain consists of registers for seconds, minutes, hours, day of week, day of month,
month, and year (including leap years). Refer to the 78M6631 Programmer’s Reference Manual for more
information regarding the use of the 78M6631 RTC.
1.13 Hardware Watchdog Timer
V1
V3P3
V3P3 - 10mV
WDT disabled
V3P3 400mV
Normal
operation,
WDT
enabled
VBIAS
Battery
modes
In addition to the basic watchdog timer included in the 80515 MPU, an
independent, robust, fixed-duration, watchdog timer (WDT) is included in
the device. It uses the crystal oscillator as its time base and must be
refreshed by the MPU firmware at least every 1.5 seconds. When not
refreshed on time the WDT overflows, and the part is reset as if the RESET
pin were pulled high, except that the IORAM bits are maintained. 4096
oscillator cycles (or 125 ms) after the WDT overflow, the MPU is launched
from program address 0x0000. Asserting ICE_E deactivates the WDT.
The WDT can also be disabled by connecting the V1 pin to V3P3D. This
also deactivates V1 power fault detection. Since there is no method in
firmware to disable the crystal oscillator or the WDT, it is guaranteed that
whatever state the part might find itself in, upon watchdog overflow, the part
is reset to a known state.
0V
Figure 3: Functions Defined by V1
Rev 2
11
78M6631 Data Sheet
DS_6631_056
1.14 Temperature Sensor
The device includes an on-chip temperature sensor for determining the temperature of the bandgap
reference. The primary use of the temperature data is to determine the magnitude of compensation
required to offset the thermal drift in the system.
1.15 General-Purpose Digital I/O
The 78M6631 includes 17 general-purpose digital I/O pins. As inputs, these pins are 5V compatible (no
current-limiting resistors are needed). On reset or power-up, all DIO pins are inputs. Their input/output
directions are subsequently set by the MPU. The digital I/O pins can be categorized as follows:
DIO3
DIO4, DIO5
DIO6
DIO8, DIO9, DIO11
DIO17
DIO24, DIO25
DIO29, DIO30
DIO45, DIO47
DIO51
DIO53, DIO55
(1
(2
(1
(3
(1
(2
(2
(2
(1
(2
pin)
pins)
pin)
pins)
pin)
pins)
pins)
pins)
pin)
pins)
DIO pin
DIO/EEPROM
DIO pin (multifunction)
DIO pins
DIO pin
DIO pins
DIO pins
DIO pins
DIO pin
DIO pins
1.16 D/Y Selection Pin
The D/Y pin selects either the Delta or the Wye configuration. At power-on, the Delta/Wye selection
register assumes the state of the D/Y pin. The register value can be modified by the software overriding
the state of the D/Y pin.
1.17 EEPROM Interface
The 78M6631 provides hardware support for an optional 2-pin or a 3-wire (MICROWIRE®) EEPROM
interface.
2-Pin EEPROM Interface
The dedicated 2-pin serial interface communicates with external EEPROM devices. The interface is
multiplexed onto the DIO4 (SDCK) and DIO5 (SDATA) pins.
3-Wire (MICROWIRE) EEPROM Interface
A 500 kHz three-wire interface, using SDATA, SDCK and a DIO pin for CS, is also available.
1.18 SPI Slave Port
The slave SPI port communicates directly with the MPU data bus and is able to directly read and write
XRAM and IORAM locations. It is also able to send commands to the MPU. The interface to the slave port
consists of the PCSZ, PCLK, PSDI, and PSDO pins.
A typical SPI transaction is as follows. While PCSZ is high, the port is held in an initialized/reset state.
During this state, PSDO is held in high-Z state and all transitions on PCLK and PSDI are ignored. When
PCSZ falls, the port begins the transaction on the first rising edge of PCLK. A transaction consists of an
8-bit command, a 16-bit address, and then one or more bytes of data. The transaction ends when PCSZ
is raised. Some transactions can consist of a command only. The last SPI command and address (if part
of the command) are available in the IORAM.
The SPI port supports data transfers at up to 1 Mbps. The SPI commands are described in Table 1 and
Figure 4 illustrates the SPI Interface read and write timing.
MICROWIRE is a registered trademark of National Semiconductor.
12
Rev 2
DS_6631_056
78M6631 Data Sheet
Table 1: SPI Command Description
Command
11xx xxxx ADDR D0 ... DN
1100 0000 ADDR D0 ... DN
10xx xxxx ADDR D0 ... DN
1000 0000 ADDR D0 ... DN
CMD
ADDR D0 ... DN
SERIAL READ
Description
Output data on PSDO is read from RAM starting with byte at ADDR.
ADDR auto increments until PCSZ is raised.
MPU SPI interrupt is generated.
Output data on PSDO is read from RAM starting with byte at ADDR.
ADDR auto increments until PCSZ is raised.
No MPU SPI interrupt is generated.
Input data on PSDI is written to RAM starting with byte at ADDR.
ADDR auto increments until PCSZ is raised.
MPU SPI interrupt is generated.
Input data on PSDI is written to RAM starting with byte at ADDR.
ADDR auto increments until PCSZ is raised.
No MPU SPI interrupt is generated.
CMD and ADDR are available to the CPU in IORAM.
D0… DN are ignored.
MPU SPI interrupt is generated.
8 bit CMD
DATA[ADDR]
16 bit Address
DATA[ADDR+1]
Extended Read . . .
PCSZ
0
7
8
C0
A15
23
24
A0
x
31
32
D0
D7
39
PSCK
(From Host) PSDI
x
C7
C6
C5
A14
A1
HI Z
(From 6531) PSDO
SERIAL WRITE
D7
8 bit CMD
D6
D1
D6
DATA[ADDR]
16 bit Address
D1
D0
DATA[ADDR+1]
PCSZ
Extended Write . . .
0
7
8
C0
A15
23
24
A0
D7
31
32
D0
D7
39
PSCK
(From Host) PSDI
x
(From 6531) PSDO
C7
C6
C5
A14
A1
D6
D1
D6
D1
D0
x
HI Z
Figure 4: SPI Slave Port: Typical Read and Write Operations
Since the addresses are in 16-bit format, any type of XRAM data can be accessed: CE, MPU, or IORAM
but not SFRs or the 80515-internal register bank.
1.19 Test Port
One out of 16 digital or eight analog signals can be selected to be output on the TMUXOUT pin. Refer to
the 78M6631 Programmer’s Reference Manual for more information regarding the use of TMUXOUT.
1.20 UART
The 78M6631 includes one UART (UART0) that can be programmed to communicate with a variety of
external devices. The UART is a dedicated 2-wire serial interfaces (no hardware flow
control/handshaking), which can communicate at rates up to 38,400 bps. All UART transfers are
programmable for parity enable, parity, 2 stop bits/1 stop bit and XON/XOFF options for variable
communication baud rates from 300 to 38,400 bps. Refer to the 78M6631 Programmer’s Reference
Manual for more information regarding the use of the UART resources.
Rev 2
13
78M6631 Data Sheet
DS_6631_056
1.21 In-Circuit Emulator (ICE) Port
The 78M6631 implements an In-Circuit Emulator (ICE) port for debug and programming of the device. To
enable the use of the port the ICE_E pin must be pulled high. In this mode the E_RST, E_TCLK, and
E_RXTX pins are enabled. Contact Maxim support for more information regarding the use of the ICE
interface for device programming and debug.
14
Rev 2
DS_6631_056
78M6631 Data Sheet
2 Electrical Specifications
2.1
Absolute Maximum Ratings
Table 2 shows the absolute maximum ranges for the device. Stresses beyond Absolute Maximum
Ratings may cause permanent damage to the device. These are stress ratings only and functional
operation at these or any other conditions beyond those indicated under recommended operating
conditions (Section 2.3) is not implied. Exposure to absolute-maximum-rated conditions for extended
periods may affect device reliability. All voltages are with respect to GNDA.
Table 2: Absolute Maximum Ratings
Voltage and Current
Supplies and Ground Pins
V3P3D, V3P3A
-0.5 V to 4.0 V
GNDD
-0.5 V to +0.5 V
Analog Output Pins
-10 mA to +10 mA,
-0.5 V to (V3P3A + 0.5 V)
VREF
Analog Input Pins
IAP, IAN, IBP, IBN, ICP, ICN, VA, VB, VC
-10 mA to +10 mA
-0.5 V to (V3P3A + 0.5 V)
XIN, XOUT
-10 mA to +10 mA
-0.5 V to 3.0 V
All Other Pins
Configured as Digital Inputs
-10 mA to +10 mA,
-0.5 to +6 V
Configured as Digital Outputs
-15 mA to +15 mA,
-0.5 V to (V3P3D + 0.5 V)
All Other Pins
-0.5 V to (V3P3D + 0.5 V)
Temperature and ESD Stress
Operating Junction Temperature (peak, 100 ms)
+140°C
Operating Junction Temperature (continuous)
+125°C
Storage Temperature
-45°C to +165°C
Lead Temperature (soldering, 10 s)
+250°C
Soldering Temperature (reflow)
+260C
ESD Stress on All Pins
4 kV
Rev 2
15
78M6631 Data Sheet
2.2
DS_6631_056
Recommended External Components
Table 3: Recommended External Components
Name
From
To
C1
V3P3A
AGND
C3
V3P3D
XTAL
Function
Value
Unit
Bypass capacitor for 3.3 V supply
0.1 20%
F
DGND
Bypass capacitor for V3P3D
1.0 30%
F
XIN
XOUT
32.768 kHz crystal, electrically similar to
ECS .327-12.5-17X or Vishay XT26T,
load capacitance 12.5 pF
32.768
kHz
CXS
XIN
AGND
Load capacitor for crystal (depends on
crystal specs and board parasitics)
33 10%
pF
CXL
XOUT
AGND
Load capacitor for crystal (depends on
crystal specs and board parasitics)
15 10%
pF
Notes:
1. AGND and DGND should be connected together.
2. V3P3Ds and V3P3A should be connected together.
2.3
Recommended Operating Conditions
Table 4: Recommended Operating Conditions
Parameter
V3P3D, V3P3A: 3.3 V Supply Voltage
(V3P3A and V3P3D must be at the same
voltage)
Operating Temperature Range
16
Condition
Min
Typ
Max
Unit
Normal operation
3.0
3.3
3.6
V
+85
ºC
-40
Rev 2
DS_6631_056
2.4
78M6631 Data Sheet
Performance Specifications
2.4.1 Input Logic Levels
Table 5: Input Logic Levels
Parameter
Condition
Min
1
Digital high-level input voltage , VIH
Typ
Max
2
V
1
Digital low-level input voltage , VIL
Input pullup current, IIL
E_RXTX,
E_RST, CKTEST
Other digital inputs
VIN = 0 V,
ICE_E = 1
Input pulldown current, IIH
ICE_E
RESET
Other digital inputs
VIN = V3P3D
Unit
10
10
-1
10
10
-1
0.8
V
0
100
100
+1
A
A
A
0
100
100
+1
A
A
A
1
To reduce power consumption, digital inputs should be below 0.3 V or above 2.5 V to minimize supply
current.
2.4.2 Output Logic Levels
Table 6: Output Logic Levels
Parameter
Condition
Digital high-level output voltage VOH
Digital low-level output voltage VOL
Min
Typ
Max
Unit
ILOAD = 1 mA
V3P3D 0.4
V
ILOAD = 15 mA
V3P3D 0.6
V
ILOAD = 1 mA
0
ILOAD = 15 mA
0.4
V
0.8
V
2.4.3 Power-Fault Comparator
Table 7: Power-Fault Comparator Performance Specifications
Parameter
Condition
Offset Voltage: V1 - VBIAS
Min
Max
Unit
-20
+15
mV
1.2
A
100
100
s
s
-10
mV
Hysteresis Current: V1
VIN = VBIAS – 100 mV
0.8
Response Time: V1
+100 mV overdrive
Voltage at V1 rising
Voltage at V1 falling
10
WDT Disable Threshold: V1 - V3P3A
Rev 2
-400
Typ
8
37
17
78M6631 Data Sheet
DS_6631_056
2.4.4 Power Supply Monitor
Table 8: Power Supply Monitor Performance Specifications (BME= 1)
Parameter
Load Resistor
LSB Value
Condition
Min
Typ
Max
Unit
–
27
45
63
kΩ
[M40MHZ, M26MHZ]
= [00], [10], or [11]
FIR_LEN=0(L=138)
FIR_LEN=1(L=288)
(-10%)
-48.7
-5.35
(+10%)
V
V
[M40MHZ, M26MHZ]
= [01]
FIR_LEN=0(L=186)
FIR_LEN=1(L=384)
(-10%)
-19.8
-2.26
(+10%)
-200
0
+100
V
V
mV
Typ
Max
Unit
Normal Operation,
V3P3A = V3P3SYS = 3.3 V
CKMPU = 614 kHz
No flash memory write
RTM_E=0, ECK_DIS=1,
ADC_E=1, ICE_E=0
4.2
6.35
mA
8.4
9.6
mA
3.3
3.8
mA
Normal operation as above, except
write flash at maximum rate, CE_E =
0, ADC_ E = 0
9.1
12
mA
Max
Unit
1
W
3
pF
5
5
pF
pF
Offset Error
2.4.5 Supply Current
Table 9: Supply Current Performance Specifications
Parameter
Condition
V3P3D current (CE off)
V3P3D current (CE on)
V3P3A current
V3P3D current,
Write Flash
Min
2.4.6 Crystal Oscillator
Table 10: Crystal Oscillator Performance Specifications
Parameter
Condition
Maximum Output Power to Crystal
XIN to XOUT Capacitance
Capacitance to DGND
XIN
XOUT
18
1
4
Crystal connected
1
Min
Typ
RTCA_ADJ = 0
Rev 2
DS_6631_056
78M6631 Data Sheet
2.4.7 Temperature Sensor
Table 11 shows the performance for the temperature sensor. The LSB values do not include the 8-bit left
shift at CE input.
Table 11: Temperature Sensor Performance Specifications
Parameter
Condition
Min
Typ
Max
Unit
Nominal relationship: N(T) = Sn*(T-Tn) + Nn, Tn = 22ºC
[M26MHZ, M40MH] =
[00], [01], or [11]
Nominal
Sensitivity (Sn)
L
S n 0.00107
3
3
Nominal Offset
(Nn) 4
L
N n 0.510
3
3
FIR_LEN= 0 (L=138)
FIR_LEN=1 (L=288)
-104
-947
[M26MHZ, M40MHZ] =
[10]
FIR_LEN=0
-255
[M26MHZ, M40MH] =
[00], [01], or [11]
FIR_LEN=0 (L=138)
FIR_LEN=1 (L=288)
[M26MHZ, M40MHZ] =
[10]
FIR_LEN=0 (L=186)
Temperature Error 2
( N (T ) N n )
Tn
ERR T
Sn
(L=186)
Tn = 22°C,
T = -40ºC to +85ºC
LSB/ºC
49641
451200
LSB
121500
-101
+101
ºC
1
Guaranteed by design; not production tested.
Nn is measured at Tn during measurement calibration and is stored in MPU or CE for use in temperature
calculations.
2
2.4.8 VREF
Table 12 shows the performance specifications for VREF. Unless otherwise specified, VREF_DIS = 0.
Table 12: VREF Performance Specifications
Parameter
VREF output voltage, VREF(22)
Condition
TA = +22ºC
Min
Typ
Max
Unit
1.193
1.195
1.197
V
40
mV
+1.5
mV/V
VREF chop step
VREF power supply sensitivity
ΔVREF/ΔV3P3A
V3P3A = 3.0 to 3.6 V
VREF input impedance
VREF_DIS = 1,
VREF = 1.3 to 1.7 V
VREF output impedance
CAL =1,
ILOAD = 10 A, -10 A
VNOM definition2
VNOM(T ) VREF(22) (T 22)TC1 (T 22) 2 TC2
VNOM temperature coefficients:
TC1
TC2
-1.5
100
k
2.5
3.18·(52.46-TRIMT)
-0.444
k
V
V/ºC
V/°C2
VREF(T) deviation from VNOM(T)
VREF (T ) VNOM (T )
10 6
VNOM (T )
max( T 22 ,40)
VREF aging
1
2
-401
+401
25
ppm/ºC
ppm/year
Guaranteed by design; not production tested.
This relationship describes the nominal behavior of VREF at different temperatures.
Rev 2
19
78M6631 Data Sheet
DS_6631_056
2.4.9 ADC Converter, V3P3A Referenced
Table 13 shows the performance specifications for the ADC converter, V3P3A referenced. For this data,
FIR_LEN = 0, VREF_DIS = 0 and LSB values do not include the 9-bit left shift at the CE input.
Table 13: ADC Converter Performance Specifications
Parameter
Condition
Recommended Input Range
(VIN - V3P3A)
Voltage to Current Crosstalk
6
10 *Vcrosstalk
cos(Vin Vcrosstalk)
Vin
VIN = 200 mV peak,
65 Hz, on VA.
Vcrosstalk = largest
measurement on IA or IB
THD (First 10 harmonics) 1:
250 mV-pk
20 mV-pk
VIN = 65 Hz,
64 kpts FFT, BlackmanHarris window
CKCE = 5 MHz
Input Impedance
VIN = 65 Hz
Temperature coefficient of Input
Impedance
VIN = 65 Hz
LSB size
1.25 3
VLSB VREF
4.75 L
L = FIR length
3
Min
Typ
Max
Unit
-250
+250
mV
peak
-101
+101
V/V
-751
-901
dB
dB
90
k
40
/°C
1.7
[M40MHZ,
M26MHZ] =
[00], [10], or [11]
[M40MHZ,
M26MHZ] =
[01]
nV/
LSB
nV/
LSB
Digital Full Scale [M40MHZ,
3
M26MHZ] =
L
[00], [10], or [11]
3
LSB
L = FIR length
[M40MHZ,
M26MHZ] =
[01]
ADC Gain Error versus
%Power Supply Variation
106 NoutPK 357nV / VIN
100 V 3P3 A / 3.3
LSB
VIN = 200 mV pk, 65
Hz, V3P3A=3.0 V, 3.6
V
Input Offset (VIN - V3P3A)
1
-10
50
ppm/%
+10
mV
Guaranteed by design; not production tested.
20
Rev 2
DS_6631_056
2.5
78M6631 Data Sheet
Timing Specifications
2.5.1 Flash Memory
Table 14: Flash Memory Timing Specifications
Parameter
Condition
Flash write cycles
-40°C to +85°C
Flash data retention
Flash data retention
Min
Typ
Max
Unit
20,000
Cycles
+25°C
100
Years
+85°C
10
Years
Flash byte write operations between
page or mass erase operations
2
Cycles
Write Time per Byte
42
s
Page Erase (1024 bytes)
20
ms
Mass Erase
200
ms
Max
Unit
2.5.2 EEPROM Interface
Table 15: EEPROM Interface Timing
Parameter
Condition
2
Write Clock frequency (I C)
Write Clock frequency (3-wire)
Min
Typ
CKMPU = 4.9152 MHz,
using interrupts
78
kHz
CKMPU = 4.9152 MHz,
bit-banging DIO4/5
150
kHz
CKMPU = 4.9152 MHz
500
kHz
2.5.3 RESET
Table 16: RESET Timing
Parameter
Reset pulse width
Reset pulse fall time
1
Condition
Min
Typ
Max
Unit
s
5
1
1
s
Guaranteed by design; not production tested.
Rev 2
21
78M6631 Data Sheet
DS_6631_056
2.5.4 SPI Slave Port
Table 17: SPI Slave Port Timing
Parameter
Condition
Min
Typ
Max
Unit
tSPIcycPCLK cycle time
1
s
tSPILead Enable lead time
15
ns
tSPILag Enable lag time
0
ns
tSPIW PCLK pulse width
High
40
Low
40
Ignore if PCLK is low
when PCSZ falls
tSPISCK PCSZ to first PCLK fall
tSPIDIS Disable time
ns
2
ns
0
ns
tSPIEV PCLK to Data Out
15
ns
tSPISUData input setup time
10
ns
tSPIHData input hold time
5
ns
PCSZ
tSPILead
tSPIcyc
tSPILag
PCLK
PSDO
tSPISCK
tSPIW
MSB OUT
tSPIEV
tSPIW
LSB OUT
tSPIDIS
tSPIH
PSDI
MSB IN
LSB IN
Figure 5: SPI Slave Port Timing
22
Rev 2
DS_6631_056
78M6631 Data Sheet
3 Packaging
3.1
56-Pin QFN Package
3.2
Pinout
Figure 6: Pinout for QFN-56 Package
Rev 2
23
78M6631 Data Sheet
DS_6631_056
3.2.1 56-Pin QFN Package Outline
24
Rev 2
DS_6631_056
78M6631 Data Sheet
3.2.2 Recommended PCB Land Pattern for the QFN-56 Package
Figure 7: PCB Land Pattern for QFN-56 Package
Rev 2
25
78M6631 Data Sheet
DS_6631_056
4 Pin Descriptions
4.1
Power and Ground Pins
Table 18: Power and Ground Pins
Name
Type
Circuit
GNDA
P
–
Analog ground: This pin should be connected directly to the ground
plane.
GNDD
P
–
Digital ground: This pin should be connected directly to the ground plane.
V3P3A
P
–
Analog power supply: A 3.3 V power supply should be connected to this
pin, must be the same voltage as V3P3SYS.
V3P3D
P
–
System 3.3 V supply. This pin should be connected to a 3.3 V power
supply.
4.2
Description
Analog Pins
Table 19: Analog Pins
Name
IAP,
IAN,
IBP,
IBN,
ICP,
ICN
VA, VB,
VC
Type
Circuit
Description
I
6
Line Current Sense Inputs: These pins are voltage inputs to the internal
A/D converter. Typically, they are connected to the outputs of current
sensors. Unused pins must be connected to V3P3A.
I
6
Line Voltage Sense Inputs: These pins are voltage inputs to the internal
A/D converter. Typically, they are connected to the outputs of resistor
dividers. Unused pins must be connected to V3P3A.
V1
I
7
Comparator Input: This pin is a voltage input to the internal comparator.
The voltage applied to the pin is compared to the internal BIAS voltage
(1.6 V). If the input voltage is above VBIAS, the comparator output is high
(1). If the comparator output is low, a voltage fault occurs. A series 5 k
resistor should be connected from V1 to the resistor divider.
VREF
O
9
Voltage Reference for the ADC. Normally disabled and left unconnected.
If enabled, a 0.1 F capacitor to V3P3A should be connected to this pin.
XIN
XOUT
I
8
Crystal Inputs: A 32 kHz crystal should be connected across these pins.
Typically, a 33 pF capacitor is also connected from XIN to GNDA and a
15 pF capacitor is connected from XOUT to GNDA. It is important to
minimize the capacitance between these pins. Refer to the crystal
manufacturer data sheet for details. If an external clock is used, a 150
mVP-P clock signal should be applied to XIN, and XOUT should be left
unconnected.
1)
Pin types: P = Power, O = Output, I = Input, I/O = Input/Output
The circuit number denotes the equivalent circuit, as specified under Section 5 I/O Equivalent Circuits.
26
Rev 2
DS_6631_056
4.3
78M6631 Data Sheet
Digital Pins
Table 20: Digital Pins
Name
DIO3
DIO4,DIO5,DIO6
DIO8, DIO9, DIO11
DIO17
DIO24, DIO25
DIO29, DIO30
DIO45, DIO47
DIO51, DIO53
DIO55
D/Y
Type
Circuit
I/O
3, 4
I/O
I
Description
Dedicated DIO pin.
3, 4, 5 Multi-use pins, DIO.
(DIO4 = SCK, DIO5 = SDA when configured as EEPROM
interface; If unused, these pins must be configured as DIOs
and set to outputs by the firmware.
–
Selects either the Delta or the Wye configuration.
PCLK
PSDO
PCSZ
PSDI
I/O
3, 4, 5 SPI PORT.
E_RXTX
I/O
1, 4, 5 Port pins (when ICE_E pulled high).
E_RST
I/O
1, 4, 5
E_TCLK
O
4, 5
ICE_E
I
2
CKTEST
I/O
3, 4
TMUXOUT
O
4
Digital test multiplexer output. Controlled by TMUX[3:0].
RESET
I
2
Chip reset: This input pin is used to reset the chip into a known
state. For normal operation, this pin is pulled low. To reset the
chip, this pin should be pulled high. This pin has an internal
30 A (typ) current source pulldown. No external reset circuitry is
necessary.
RX
I
3
UART input. If this pin is unused, it must be terminated to
V3P3D or GNDD.
TX
O
4
UART output.
GNDD (pin 55)
I
7
Enables Production Test. This pin must be grounded in normal
operation.
ICE enable. When zero, E_RST, E_TCLK and E_RXTX SEG32
For production units, this pin should be pulled to GND to disable
the emulator port.
Test clock.
Pin types: P = Power, O = Output, I = Input, I/O = Input/Output.
The circuit number denotes the equivalent circuit, as specified in Section 5, I/O Equivalent Circuits.
Rev 2
27
78M6631 Data Sheet
DS_6631_056
5 I/O Equivalent Circuits
V3P3D
V3P3A
V3P3D
110K
Digital
Input
Pin
CMOS
Input
from
internal
reference
LCD SEG
Output
Pin
LCD
Driver
VREF
Pin
GNDD
GNDD
GNDA
LCD Output Equivalent Circuit
Type 5:
LCD SEG or
pin configured as LCD SEG
Digital Input Equivalent Circuit
Type 1:
Standard Digital Input or
pin configured as DIO Input
with Internal Pull-Up
VREF Equivalent Circuit
Type 9:
VREF
V3P3A
V3P3D
V3P3D
Digital
Input
Pin
CMOS
Input
Analog
Input
Pin
GNDD
GNDD
Analog Input Equivalent Circuit
Type 6:
ADC Input
Digital Input
Type 2:
Pin configured as DIO Input
with Internal Pull-Down
V2P5 Equivalent Circuit
Type 10:
V2P5
V3P3A
V3P3D
Comparator
Input
Pin
To
Comparator
LCD
Drivers
VLCD
Pin
GNDA
Digital
Input
Pin
CMOS
Input
GNDD
GNDD
Comparator Input Equivalent
Circuit Type 7:
Comparator Input
Oscillator
Pin
Digital Input Type 3:
Standard Digital Input or
pin configured as DIO Input
VLCD Equivalent Circuit
Type 11:
VLCD Power
To
Oscillator
Power
Down
Circuits
VBAT
Pin
GNDD
V3P3D
GNDD
Oscillator Equivalent Circuit
Type 8:
Oscillator I/O
V3P3D
Digital
Output
Pin
CMOS
Output
V2P5
Pin
GNDA
110K
GNDD
from
internal
reference
To
MUX
GNDD
GNDD
Digital Output Equivalent Circuit
Type 4:
Standard Digital Output or
pin configured as DIO Output
from
V3P3SYS
10
VBAT Equivalent Circuit
Type 12:
VBAT Power
V3P3D
Pin
from
VBAT
40
V3P3D Equivalent Circuit
Type 13:
V3P3D
Figure 8: I/O Equivalent Circuits
28
Rev 2
DS_6631_056
78M6631 Data Sheet
6 Ordering Information
Table 21: Ordering Information
Part
Part Description
(Package)
Flash
Size
78M6631
56-pin QFN, Lead(Pb)Free
128 KB
7
Packaging
Order Number
Bulk
78M6631-IM/F
Tape and Reel
78M6631-IMR/F
Package
Marking
78M6631
Contact Information
For more information about Maxim products or to check the availability of the 78M6631, contact technical
support at www.maxim-ic.com/support.
Rev 2
29
DS_6631_056
78M6631 Data Sheet
Revision History
REVISION
NUMBER
REVISION
DATE
0
9/11
Initial release
1
1/12
Removed information about programmed devices from
Table 21. Ordering Information
29
2
4/12
Removed “-IM” from the Package Marking
29
DESCRIPTION
PAGES
CHANGED
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical
Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
30
© Maxim Integrated
Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000
The Maxim logo and Maxim Integrated are trademarks of Maxim Integrated Products, Inc.
工商网监
湘ICP备2023018690号
