DS1811-15+

DS1811 5V EconoReset with Open Drain Output www.maxim-ic.com FEATURES § § § § § § § PIN ASSIGNMENT Automatically restarts a microprocessor after power failure Maintains reset for 150 ms after VCC returns to an in-tolerance condition Reduces need for discrete components Precision temperature-compensated voltage reference and voltage sensor Low-cost TO-92 or space saving SOT-23 packages available Efficient open-drain output with internal 5.5 kW pull-up resistor Operating temperature -40°C to +85°C 3 DALLAS DS1811 Econo Reset 1 1 2 3 2 TOP VIEW SOT-23 PACKAGE See Mech. Drawings Section On Website 1 2 3 BOTTOM VIEW TO-92 PACKAGE See Mech. Drawings Section On Website PIN DESCRIPTION TO-92 1 2 3 RST VCC GND Active Low Reset Output Power Supply Ground SOT-23 1 2 3 RST VCC GND Active Low Reset Output Power Supply Ground DESCRIPTION The DS1811 EconoReset uses a precision temperature reference and comparator circuit to monitor the status of the power supply (VCC). When an out-of-tolerance condition is detected, an internal power-fail signal is generated which forces reset to the active state. When VCC returns to an in-tolerance condition, the reset signal is kept in the active state for approximately 150 ms to allow the power supply and processor to stabilize. 1 of 5 041002 DS1811 OPERATION - POWER MONITOR The DS1811 provides the functions of detecting out-of-tolerance power supply conditions and warning a processor-based system of impending power failure. When VCC is detected as out-of-tolerance, the RST signal is asserted. On power-up, RST is kept active for approximately 150 ms after the power supply has reached the selected tolerance. This allows the power supply and microprocessor to stabilize before RST is released. BLOCK DIAGRAM (OPEN-DRAIN OUTPUT) Figure 1 APPLICATION EXAMPLE Figure 2 2 of 5 DS1811 TIMING DIAGRAM: POWER-UP Figure 3 TIMING DIAGRAM: POWER-DOWN Figure 4 3 of 5 DS1811 ABSOLUTE MAXIMUM RATINGS* Voltage on VCC Pin Relative to Ground Voltage on RST Relative to Ground Operating Temperature Storage Temperature Soldering Temperature * -0.5V to +7.0V -0.5V to VCC +0.5V -40°C to +85°C -55°C to +125°C 260°C for 10 seconds This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. RECOMMENDED DC OPERATING CONDITIONS PARAMETER Supply Voltage SYMBOL VCC DC ELECTRICAL CHARACTERISTICS PARAMETER MIN 0.0 (-40°C to +85°C) TYP MAX 5.5 UNITS V NOTES 1 (-40°C to +85°C; VCC=1.2V to 5.5V) SYMBOL MIN Output Current @ 0.4 volts IOL +10 Operating Current VCC < 5.5 volts ICC TYP MAX UNITS NOTES mA 2, 3 30 40 mA 4 VCC Trip Point (DS1811-5) VCCTP 4.50 4.62 4.75 V 1 VCC Trip Point (DS1811-10) VCCTP 4.25 4.35 4.49 V 1 VCC Trip Point (DS1811-15) VCCTP 4.00 4.13 4.24 V 1 RP 3.5 5.5 7.5 kW 10 pF Internal Pull-Up Resistor Output Capacitance COUT AC ELECTRICAL CHARACTERISTICS PARAMETER (-40°C to +85°C; VCC=1.2V to 5.5V) SYMBOL MIN TYP MAX UNITS RESET Active Time tRST 100 150 300 ms VCC Detect to RST tRPD 2 5 ms VCC Slew Rate (VCCTP (MAX) to VCCTP (MIN)) tF 300 ms VCC Slew Rate (VCCTP (MIN) to VCCTP (MAX)) tR 0 ns tRPU 100 VCC Detect to RST 4 of 5 150 300 ms NOTES 5 DS1811 NOTES: 1. All voltages are referenced to ground. 2. Measured with VCC ³ 2.7 volts. 3. A 1kW external resistor may be required in some applications for proper operation of the microprocessor reset control circuit. 4. Measured with RST output open. 5. tR = 5 ms. PART MARKING CODES “A”, “B”, &“C” represent the device type. 810 . . . . DS1810 811 . . . . DS1811 812 . . . . DS1812 813 . . . . DS1813 815 . . . . DS1815 816 . . . . DS1816 817 . . . . DS1817 818 . . . . DS1818 “D” represents the device tolerance. A . . . . . . 5% B . . . . . . 10% C . . . . . . 15% D . . . . . . 20% 5 of 5