DS2149DK

DS2149DK/DS21349DK T1/J1 Line Interface Unit Design Kit www.maxim-ic.com GENERAL DESCRIPTION FEATURES The DS2149DK/DS21349DK is a fully integrated design kit for the DS2149 and the DS21349 T1/J1 line interface units (LIUs). It contains the necessary circuitry to evaluate the device in all operation modes, including running the device in hardware and software mode. § § § § DESIGN KIT CONTENTS § § DS2149DK/DS21349DK Board DS2149 28-Pin PLCC DS21349 28-Pin PLCC § § PLCC 28-Pin Socket for Multiple Part Evaluation Bantam and RJ48 Connectors, Transformers, and Termination Passives for LIU Two Separate and Controllable Transmit Paths for TTIP and TRING for Evaluating Multiple Transformers Equipment-Side Connector for External Data Source/Sink or External Remote Loopback On-Board T1 Crystal Oscillator On-Board 8051 Microprocessor for Software Mode Access Connector Accesses to CS, SCLK, SDI, and SDO for Firmware Development Controllable 5V and 3.3V for VCC and IO Pins to Support the DS2149 and DS21349 LIUs ORDERING INFORMATION PART DS2149DK/ DS21349DK 1 of 14 DESCRIPTION T1/J1 Line Interface Unit Design Kit REV: 032403 DS2149DK/DS21349DK T1/J1 Line Interface Unit Design Kit COMPONENT LIST DESIGNATION C1 C3, C6, C9, C12, C15–C17, C19 C4, C7, C10, C21 C5, C8, C11, C22, C23 C13, C14 QTY DESCRIPTION 1 SUPPLIER PART 0.001mF capacitor (SMT80123) Digi-Key — 8 10mF capacitors (SMT80123) Digi-Key — 4 0.1mF capacitors (SMT80123) Digi-Key — 5 0.01mF capacitors (SMT80123) Digi-Key — 2 10mF capacitors (SMT127240) Digi-Key — C18, C20 2 22pF capacitors (SMT80123) Digi-Key — DS1–DS3, DS5 4 Red LED Digi-Key LN1251C DS7 1 150-mil SO, DS87C520-ECL Dallas Semiconductor DS87C520-ECL 15-43-8588 J1 1 Connector, RJ48, 8-pin Digi-Key J2, J3 2 Bantam connectors Digi-Key RTT34B02 J4–J11 8 Coto Technology COTO9802 J12 1 Digi-Key — JP1 1 COTO9802 100-mil, 16-pin vertical connector Pushbutton switch Digi-Key EVQPAE04M JP2–JP6 5 100-mil SIP jumper 2 position Digi-Key — JP7–JP10 4 100-mil SIP jumper 3 position Digi-Key — PWR_CONNBAN2 1 Banana connector, 2-pin, red Mouser Electronics 164-6219 PWR_CONNBAN1 1 Banana connector, 2-pin, black Mouser Electronics 164-6218 R1–R3, R12, R14 5 300W resistors (SMT80123) Digi-Key — R4, R5 2 4.7W resistors (SMT80123) Digi-Key — R6, R7, R10, R11 4 0W resistors (SMT80123) Digi-Key — R8, R9 2 50.0W resistors (SMT80123) Digi-Key — R13, R15, R16 3 10.0kW resistors SMT80123) Digi-Key — R17–R21 5 30W resistors (SMT80123) Digi-Key — — RN1, RN2 2 1kW 10-pin resistor network Digi-Key S1 1 9-pin DB9P connector Digi-Key 747459-1 SW1 1 10-position switch Digi-Key 435668-9 SW2 1 6-pin DPDT switch Digi-Key SSA22 T1 1 1:3 T1 transformer Pulse Engineering PE-64933 T2 1 1:2 T1 transformer Pulse Engineering PE-65771 T3 1 1:1 T1 transformer Pulse Engineering PE-64936 U1 1 Pioneer Electronics PLCCSMT28T0T U2, U5, U7 3 Digi-Key TC74HC04AFN U3, U4, U6 3 Digi-Key SN74LS38D Texas Instruments ULQ2003ADR Dallas Semiconductor DS232AR U8 1 PLCCSMT28T0T socket 150-mil SO, 74HC04, hex inverter 150-mil SO, 74HC03, open collector NAND gate Darlington array U9 1 150-mil SO, DS232AR U10 1 3.3V regulator Maxim MAX8887EZK33 X1 1 EC1-S-11.0592M XTAL low pro Digi-Key EC1-S-11.0592M Y1 1 1.544MHz crystal oscillator Digi-Key NTH039A3-1.5440 2 of 14 DS2149DK/DS21349DK T1/J1 Line Interface Unit Design Kit BOARD FLOORPLAN Figure 1 shows the board layout for the DS2149DK. The DS2149 PLCC socket is in the center of the board. The line-side bantam connectors for the Tx and Rx differential pairs and transformers are at the bottom of the board, while the system connector and configuration jumpers are at the top. The LEDs for INT, INLOOP, and RCL/QPD are in the center of the board, right above the DS2149 socket. The power-supply connectors and power indicator LED are in the upper left corner of the board, while the DB9 serial connector is the upper left. A T1 oscillator sits to the left of the DS2149 socket below a switch for changing the voltage to the DS2149 socket from 5V to 3.3V. Please refer to the general locations on the board when this document references specific items on the DS2149DK. Figure 1. Board Floorplan SYSTEM CONNECTOR VDD GND POWER JACKS LEDs SERIAL PORT NLOOP PWR RCL LED INT Dallas Semiconductor DS2149DK/ DS21349DK OSCILLATOR DS2149 T1 CONFIGURATION JUMPERS TRANSFORMERS Tx Tx Rx CONFIGURATION SWITCHES LINE CONNECTORS Rx Tx 3 of 14 DS2149DK/DS21349DK T1/J1 Line Interface Unit Design Kit LINE-SIDE CONNECTIONS The DS2149DK/DS21349DK implements the Tx and Rx line interface networks recommended in the DS2149 and DS21349 data sheets and as shown in Figure 2. To connect the DS2149DK/DS21349DK to T1 or J1 test equipment, connect the equipment to the RJ48 connector or to the two bantam connectors, J2 and J3. Please notice the relays disconnecting TTIP and TRING on T1 and T2. These relays disconnect the series resistors R4 and R5, which is recommended for some long-haul configurations. Pin 16 on the system connector serves as the control line for the relays. When pin 16 is high, T2 is enabled with TTIP and TRING. When it is held low, T1 is enabled with TTIP and TRING. Figure 2. Line-Side Circuitry J2 TRANSMIT T1 C2 1mF TTIP TRING T2 Dallas Semiconductor DS2149/DS21349 R4 4.7W (1%) J3 RECEIVE R5 4.7W (1%) T3 RTIP R9 50W (1%) R8 50W (1%) 4 of 14 RRING DS2149DK/DS21349DK T1/J1 Line Interface Unit Design Kit SYSTEM CONNECTOR A 16-pin system connector at the top of the board gives access to the following signals: RPOS, TPOS, RNEG, TNEG, RCLK_CON, TCLK, MCLK, VDD, GND, CS, SCLK, SDI, and RELAY_CONTROL. By using jumpers to connect TCLK to RCLK_CON, TPOS to RPOS, and TNEG to RNEG, the system connector can also be used to implement an external remote loopback. Additionally, the system connector can read and write to the device without going through the on-board microcontroller. With this feature, you can quickly use this design kit as a working prototype and begin writing firmware for your system. Figure 3 shows a representation of the system connector. Figure 3. System Connector RPOS CS TPOS RNEG SCLK SDI TNEG SDO RCLK GND TCLK GND MCLK GND VDD RELAY_CONTROL POWER-SUPPLY CONNECTORS Connect a 5.0V power supply across the red (VDD) and black (GND) banana jacks. The red PWR LED indicates power is applied to the board. Select the appropriate voltage that needs to be applied to VDD from the power switch below the PWR LED, depending if you are using a DS2149 (5V) or DS21349 (3.3V). MICROCONTROLER AND SERIAL CONNECTOR The DS2149DK/DS21349DK contains an on-board 8051 microcontroller with factory-installed firmware loaded into the microcontroller’s EPROM. This firmware translates memory access requests from the RS-232 serial port into register access to the DS2149 or DS21349 in software mode. DemoView, a software application created by Dallas Semiconductor, allows easy read-write access for this device. INSTALLING AND RUNNING THE SOFTWARE DemoView is a general-purpose program that supports several Dallas Semiconductor design kits. To install the DemoView software, run SETUP.EXE from the DemoView.ZIP file. (Download DemoView.ZIP from our website, After installation, run the DEMOVIEW.EXE program with the www.maxim-ic.com/telecom.) DS2149DK/DS21349DK board powered up and connected to the PC. In the opening screen, click the REGVIEW button. Select the correct serial port in the Port Selection dialog box, then click OK. To configure DEMOVIEW to support the DS2149DK/DS21349DK, open the File pulldown menu and select Definition File. In the Choose Definition File dialog box, select DS2149DK.DEF and click Open. After selecting the definition file, the main part of the REGVIEW window displays the DS2149’s memory map. To select a register, click on it in the register map. When a register is selected, the full name of the register and its bit map are displayed at the bottom of the REGVIEW window. Bits that are logic 0 are displayed in white, while bits that are logic 1 are displayed in green. The DemoView software supports the following actions: Toggle a bit. Select the register in the register map and then click the bit in the bit map. Write a register. Select the register, click the Write button, and enter the value to be written. Write all registers. Click the Write All button and enter the value to be written. Read a register. Select the register in the register map and click the Read button. Read all registers. Click the Read All button. § § § § § 5 of 14 DS2149DK/DS21349DK T1/J1 Line Interface Unit Design Kit BASIC CONFIGURATION The following example configurations provide a quick start to using the DS2149DK/DS21349DK, although there are many ways they can be configured. To set up other configurations, refer to the DS2149/DS21349 data sheets in addition to this data sheet. T1 Hardware Mode—External Remote Loopback 1) On the system connector, jumper TPOS to RPOS, TNEG to RNEG, RCLK_CON to TCLK, and RELAY_CONTROL to GND. 2) JP8, jumper RCLK to CON. 3) Remove JP5, TCLK_EN. 4) Jumper JP6 MCLK_EN. 5) JP9, JASEL, jumper to GND. 6) JP7, TAIS, jumper to GND. 7) JP10, MODE0, jumper to GND. 8) Jumper JP3, MODE1_EN. 9) Jumper JP4, RLS_EN. 10) Jumper JP2, LLB_EN. 11) On SW1, switch MODE1 to MODE1_LO. 12) On SW1, switch L0 to L0_HI. 13) On SW1, switch L1 to L1_HI. 14) On SW1, switch L2 to L2_LO. 15) On SW1, switch L3 to L3_LO. 16) On SW1, switch RLB to RLB_LO. 17) On SW1, switch LLB to LLB_LO. 18) Place appropriate device in socket. 19) Select the power 5V or 3V depending on which device you use. 20) Connect J2 and J3 to test equipment Device should be in external remote loopback. T1 Software Mode—External Remote Loopback 1) On the system connector, jumper TPOS to RPOS, TNEG to RNEG, RCLK_CON to TCLK, and RELAY_CONTROL to GND. 2) JP8, jumper RCLK to CON. 3) Remove JP5, TCLK_EN. 4) Jumper JP6 MCLK_EN. 5) JP9, JASEL, jumper to GND. 6) JP7, TAIS, jumper to GND. 7) JP10, MODE0, jumper to GND. 8) Jumper JP3, MODE1_EN. 9) Jumper JP4, RLS_EN. 10) Jumper JP2, LLB_EN. 11) On SW1, switch MODE1 to MODE1_HI. 12) Place appropriate device in socket. 13) Select the power 5V or 3V depending on which device you use. 14) Connect J2 and J3 to test equipment. 15) Load the DemoView software. 16) Select RegView. 17) Load the DS2149.DEF file. 18) Write CR1 to 0x03. 19) Write CR2 to 0x00. 20) Write CR3 to 0x00. 21) Write CR4 to 0x00. Device should be in external remote loopback. 6 of 14 DS2149DK/DS21349DK T1/J1 Line Interface Unit Design Kit DS2149/DS21349 INFORMATION For more information about the DS2149 and DS21349, please consult the DS2149 and DS21349 data sheets available on our website, www.maxim-ic.com/telecom. TECHNICAL SUPPORT For technical support, please email your questions to telecom.support@dalsemi.com. SCHEMATICS The DS2149DK/DS21349DK schematics are featured in the following 14 pages. 7 of 14