DS2153Q-A7+T&R

DS2153Q E1 Single-Chip Transceiver www.maxim-ic.com PIN CONFIGURATION Complete E1 (CEPT) PCM-30/ISDN-PRI Transceiver Functionality On-Board Line Interface for Clock/Data Recovery and Waveshaping 32-Bit or 128-Bit Jitter Attenuator Generates Line Build-Outs for Both 120Ω and 75Ω Lines Frames to FAS, CAS, and CRC4 Formats Dual On-Board Two-Frame Elastic Store Slip Buffers That can Connect to Backplanes Up to 8.192MHz 8-Bit Parallel Control Port That can be Used on Either Multiplexed or Nonmultiplexed Buses Extracts and Inserts CAS Signaling Detects and Generates Remote and AIS Alarms Programmable Output Clocks for Fractional E1, H0, and H12 Applications Fully Independent Transmit and Receive Functionality Full Access to Both Si and Sa Bits Three Separate Loopbacks for Testing Large Counters for Bipolar and Code Violations, CRC4 Codeword Errors, FAS Errors, and E Bits Pin Compatible with DS2151Q T1 SingleChip Transceiver 5V Supply; Low-Power CMOS PART DS2153Q DS2153Q+ DS2153QN DS2153QN+ ELASTIC STORES PARALLEL CONTROL PORT Dallas DS2153Q T1SCT CS RD(DS) AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 TCHCLK 6 5 4 3 2 1 44 43 42 41 40 ACTUAL SIZE OF 44-PIN PLCC ALE(AS) 7 WR (R/W) 8 9 39 38 37 DS2153Q 10 36 26 27 XTAL2 INT1 28 25 XTAL1 TSER TCLK DVDD TSYNC TLINK TLCLK TCHBLK TRING TVDD TVSS TTIP INT2 24 RVSS 19 23 18 RVDD 30 29 17 22 31 16 RRING 32 15 21 33 14 20 34 13 BTS 35 12 RTIP 11 ACLKI RLINK RLCLK DVSS RCLK RCHCLK RSER RSYNC RLOS/LOTC SYSCLK ORDERING INFORMATION TEMP RANGE 0°C to +70°C 0°C to +70°C -40°C to +85°C -40°C to +85°C FRAMER LONG & SHORT HAUL LINE INTERFACE FUNCTIONAL BLOCKS RCHBLK FEATURES PLCC PINPACKAGE 44 PLCC 44 PLCC 44 PLCC 44 PLCC +Denotes lead-free/RoHS-compliant package. Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device may be simultaneously available through various sales channels. For information about device errata, click here: www.maxim-ic.com/errata. 1 of 60 REV: 01106 DS2153Q TABLE OF CONTENTS 1 DETAILED DESCRIPTION....................................................................................................4 1.1 1.2 2 INTRODUCTION ................................................................................................................................ 4 READER’S NOTE.............................................................................................................................. 4 PIN DESCRIPTION................................................................................................................6 2.1 3 4 DS2153Q REGISTER MAP............................................................................................................... 8 PARALLEL PORT .................................................................................................................9 CONTROL AND TEST REGISTERS...................................................................................10 4.1 4.2 4.3 4.4 4.5 5 LOCAL LOOPBACK ......................................................................................................................... 17 REMOTE LOOPBACK ...................................................................................................................... 17 FRAMER LOOPBACK ...................................................................................................................... 17 AUTOMATIC ALARM GENERATION................................................................................................... 17 POWER-UP SEQUENCE ................................................................................................................. 17 STATUS AND INFORMATION REGISTERS ......................................................................18 5.1 6 CRC4 SYNC COUNTER ................................................................................................................. 20 ERROR COUNT REGISTERS.............................................................................................26 6.1 6.2 6.3 6.4 BPV OR CODE VIOLATION COUNTER ............................................................................................. 26 CRC4 ERROR COUNTER ............................................................................................................... 27 E-BIT COUNTER ............................................................................................................................ 27 FAS BIT ERROR COUNTER ............................................................................................................ 28 7 SA DATA LINK CONTROL AND OPERATION ..................................................................29 8 SIGNALING OPERATION...................................................................................................30 9 TRANSMIT IDLE REGISTERS............................................................................................32 10 CLOCK BLOCKING REGISTERS....................................................................................33 11 ELASTIC STORES OPERATION.....................................................................................35 12 ADDITIONAL (SA) AND INTERNATIONAL (SI) BIT OPERATION .................................36 13 LINE INTERFACE FUNCTIONS.......................................................................................39 13.1 13.2 13.3 14 15 16 17 RECEIVE CLOCK AND DATA RECOVERY....................................................................................... 40 TRANSMIT WAVESHAPING AND LINE DRIVING .............................................................................. 41 JITTER ATTENUATOR .................................................................................................................. 42 TIMING DIAGRAMS .........................................................................................................46 DC CHARACTERISTICS..................................................................................................52 AC CHARACTERISTICS..................................................................................................53 PACKAGE INFORMATION..............................................................................................60 17.1 44-PIN PLCC (56-G4003-001).................................................................................................. 60 2 of 60 DS2153Q LIST OF FIGURES Figure 1-1. DS2153Q Block Diagram ......................................................................................................... 5 Figure 13-1. External Analog Connections............................................................................................... 43 Figure 13-2. Jitter Tolerance .................................................................................................................... 44 Figure 13-3. Transmit Waveform Template .............................................................................................. 44 Figure 13-4. Jitter Attenuation .................................................................................................................. 45 Figure 14-1. Receive Side Timing ............................................................................................................ 46 Figure 14-2. Receive Side Boundary Timing (with Elastic Stores Disabled) ............................................ 46 Figure 14-3. 1.544MHz Boundary Timing with Elastic Store(s) Disabled ................................................. 47 Figure 14-4. 2.048MHz Boundary Timing with Elastic Store(s) Enabled.................................................. 47 Figure 14-5. Transmit Side Timing ........................................................................................................... 48 Figure 14-6. Transmit Side Boundary Timing ........................................................................................... 48 Figure 14-7. G.802 Timing........................................................................................................................ 49 Figure 14-8. Synchronization Flowchart ................................................................................................... 50 Figure 14-9. Transmit Data Flow .............................................................................................................. 51 Figure 16-1. Intel Bus Read AC Timing.................................................................................................... 54 Figure 16-2. Intel Bus Write AC Timing .................................................................................................... 54 Figure 16-3. Motorola Bus AC Timing ...................................................................................................... 55 Figure 16-4. Receive Side AC Timing ...................................................................................................... 57 Figure 16-5. Transmit Side AC Timing ..................................................................................................... 59 LIST OF TABLES Table 4-1. Sync/Resync Criteria............................................................................................................... 11 Table 5-1. Alarm Set and Clear Criteria ................................................................................................... 22 Table 13-1. Source of RCLK Upon RCL................................................................................................... 40 Table 13-2. LBO Select in LICR ............................................................................................................... 41 Table 13-3. Transformer Specifications.................................................................................................... 41 Table 13-4. Crystal Selection Guidelines ................................................................................................. 42 Table 15-1. Recommended DC Characteristics ....................................................................................... 52 Table 15-2. Capacitance .......................................................................................................................... 52 Table 15-3. DC Characteristics ................................................................................................................ 52 Table 16-1. AC Characteristics—Parallel Port ......................................................................................... 53 Table 16-2. AC Characteristics—Receive Side ........................................................................................ 56 Table 16-3. AC Characteristics—Transmit Side ....................................................................................... 58 3 of 60 DS2153Q 1 DETAILED DESCRIPTION The DS2153Q E1 single-chip transceiver (SCT) contains all the necessary functions for connection to E1 lines. The on-board clock/data recovery circuitry coverts the AMI/HDB3 E1 waveforms to a NRZ serial stream. The DS2153Q automatically adjusts to E1 22 AWG (0.6mm) twisted-pair cables from 0 to 1.5km. The device can generate the necessary G.703 waveshapes for both 75Ω and 120Ω cables. The on-board jitter attenuator (selectable to either 32 bits or 128 bits) can be placed in either the transmit or receive data paths. The framer locates the frame and multiframe boundaries and monitors the data stream for alarms. It is also used for extracting and inserting signaling data, Si, and Sa-bit information. The device contains a set of 71 8-bit internal registers that the user can access to control the operation of the unit. Quick access via the parallel control port allows a single micro to handle many E1 lines. The device fully meets all the latest E1 specifications, including ITU G.703, G.704, G.706, G.823, and I.431 as well as ETSI 300 011, 300 233, TBR 12 and TBR 13. 1.1 Introduction The analog AMI waveform off of the E1 line is transformer coupled into the RRING and RTIP pins of the DS2153Q. The device recovers clock and data from the analog signal and passes it through the jitter attenuation mux to the receive side framer where the digital serial stream is analyzed to locate the framing pattern. If needed, the receive side elastic store can be enabled in order to absorb the phase and frequency differences between the recovered E1 data stream and an asynchronous backplane clock which is provided at the SYSCLK input. The transmit side of the DS2153Q is totally independent from the receive side in both the clock requirements and characteristics. The transmit formatter will provide the necessary data overhead for E1 transmission. Once the data stream has been prepared for transmission, it is sent via the jitter attenuation mux to the waveshaping and line driver functions. The DS2153Q will drive the E1 line from the TTIP and TRING pins via a coupling transformer. 1.2 Reader’s Note This data sheet assumes a particular nomenclature of the E1 operating environment. There are 32 8-bit time slots in E1 systems that are numbered 0 to 31. Time slot 0 is transmitted first and received first. These 32 time slots are also referred to as channels with a numbering scheme of 1 to 32. Time slot 0 is identical to channel 1, time slot 1 is identical to channel 2, and so on. Each time slot (or channel) is made up of 8 bits numbered 1 to 8. Bit number 1 is the MSB and is transmitted first. Bit number 8 is the LSB and is transmitted last. Throughout this data sheet, the following abbreviations are used: FAS CAS MF Si CRC4 CCS Sa E-bit Frame Alignment Signal Channel Associated Signaling Multiframe International Bits Cyclical Redundancy Check Common Channel Signaling Additional bits CRC4 Error bits 4 of 60 DS2153Q Figure 1-1. DS2153Q Block Diagram 5 of 60 DS2153Q 2 PIN DESCRIPTION PIN 1–4, 41–44 5 6 NAME AD4–AD7, AD0–AD3 RD (DS) TYPE CS I I 7 ALE(AS) I 8 WR (R/ W ) I 9 RLINK O 10 RLCLK O 11 12 DVSS RCLK — O 13 RCHCLK O 14 RSER O 15 RSYNC I/O 16 RLOS/LOTC O 17 SYSCLK I 18 RCHBLK O 19 ACLKI I I/O FUNCTION Address/Data Bus. An 8-bit multiplexed address/data bus. Active-Low Read Input (Data Strobe) Active-Low Chip Select. Must be low to read or write the port. Address Latch Enable (Address Strobe). A positive going edge serves to demultiplex the bus. Active-Low Write Input (Read/Write) Receive Link Data. Outputs the full receive data stream including the Sa bits. See Section 14 for timing details. Receive Link Clock. 4kHz to 20kHz demand clock for the RLINK output. Controlled by RCR2. See Section 14 for timing details. Digital Signal Ground. 0.0V. Should be tied to local ground plane. Receive Clock. Recovered 2.048MHz clock. Receive Channel Clock. 256kHz clock that pulses high during the LSB of each channel. Useful for parallel to serial conversion of channel data. See Section 14 for timing details. Receive Serial Data. Received NRZ serial data, updated on rising edges of RCLK or SYSCLK. Receive Sync. An extracted pulse, one RCLK wide, is output at this pin, which identifies either frame (RCR1.6 = 0) or multiframe boundaries (RCR1.6 = 1). If the elastic store is enabled via the RCR2.1, then this pin can be enabled to be an input via RCR1.5 at which a frame boundary pulse is applied. See Section 14 for timing details. Receive Loss of Sync/Loss of Transmit Clock. A dual function output. If TCR2.0 = 0, will toggle high when the synchronizer is searching for the E1 frame and multiframe; if TCR2.0 = 1, will toggle high if the TCLK pin has not toggled for 5µs. System Clock. 1.544MHz or 2.048MHz clock. Only used when the elastic store functions are enabled via either RCR2.1. Should be tied low in applications that do not use the elastic store. If tied high for at least 100µs, will force all output pins (including the parallel port) to tri-state. Receive Channel Block. A user-programmable output that can be forced high or low during any of the 32 E1 channels. Useful for blocking clocks to a serial UART or LAPD controller in applications where not all E1 channels are used such as Fractional E1, 384kbps service (H0), 1920kbps (H12), or ISDN-PRI. Also useful for locating individual channels in drop-and-insert applications. See Section 14 for timing details. Alternate Clock Input. Upon a receive carrier loss, the clock applied at this pin (normally 2.048MHz) will be routed to the RCLK pin. If no clock is routed to this pin, then it should be tied to DVSS via a 1kΩ resistor. 6 of 60 DS2153Q PIN NAME TYPE 20 BTS I 21, 22 RTIP, RRING — 23 RVDD — 24 RVSS XTAL1, XTAL2 — 27 INT1 O 28 INT2 O 29 TTIP — 30 TVSS — 31 TVDD — 32 TRING — 33 TCHBLK O 34 TLCLK O 35 TLINK I 36 TSYNC I/O 37 DVDD — 38 TCLK I 39 TSER I 40 TCHCLK O 25, 26 — FUNCTION Bus Type Select. Strap high to select Motorola bus timing; strap low to select Intel bus timing. This pin controls the function of the RD (DS), ALE(AS), and WR (R/ W ) pins. If BTS = 1, then these pins assume the function listed in parentheses (). Receive Tip and Ring. Analog inputs for clock recovery circuitry; connects to a 1:1 transformer (see Section 13 for details). Receive Analog Positive Supply. 5.0V. Should be tied to DVDD and TVDD pins. Receive Signal Ground. 0V. Should be tied to local ground plane. Crystal Connections. A pullable 8.192MHz crystal must be applied to these pins. See Section 13 for crystal specifications. Receive Alarm Interrupt 1. Flags host controller during alarm conditions defined in Status Register 1. Active low, open drain output. Receive Alarm Interrupt 2. Flags host controller during conditions defined in Status Register 2. Active low, open drain output. Transmit Tip. Analog line driver output; connects to a step-up transformer (see Section 13 for details). Transmit Signal Ground. 0V. Should be tied to local ground plane. Transmit Analog Positive Supply. 5.0V. Should be tied to DVDD and RVDD pins. Transmit Ring. Analog line driver outputs; connects to a step-up transformer (see Section 13 for details). Transmit Channel Block. A user-programmable output that can be forced high or low during any of the 32 E1 channels. Useful for blocking clocks to a serial UART or LAPD controller in applications where not all E1 channels are used such as Fractional E1, 384kbps service (H0), 1920kbps (H12), or ISDN-PRI. Also useful for locating individual channels in drop-and-insert applications. See Section 14 for timing details. Transmit Link Clock. 4kHz to 20kHz demand clock for the TLINK input. Controlled by TCR2. See Section 14 for timing details. Transmit Link Data. If enabled, this pin will be sampled on the falling edge of TCLK to insert the Sa bits. See Section 14 for timing details. Transmit Sync. A pulse at this pin will establish either frame or multiframe boundaries for the DS2153Q. Via TCR1.1, the DS2153Q can be programmed to output either a frame or multiframe pulse at this pin. See Section 14 for timing details. Digital Positive Supply. 5.0V. Should be tied to RVDD and TVDD pins. Transmit Clock. 2.048MHz primary clock. Transmit Serial Data. Transmit NRZ serial data, sampled on the falling edge of TCLK. Transmit Channel Clock. 256kHz clock that pulses high during the LSB of each channel. Useful for parallel to serial conversion of channel data. See Section 14 for timing details. 7 of 60 DS2153Q 2.1 DS2153Q Register Map ADDRESS 00 01 02 03 04 05 06 07 08 10 11 12 13 14 15 16 17 18 19 1A 1B 1E 1F 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F R/W R R R R R R R R R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R R R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W REGISTER NAME BPV or Code Violation Count 1 BPV or Code Violation Count 2 CRC4 Count 1/FAS Error Count 1 CRC4 Error Count 2 E-Bit Count 1/FAS Error Count 2 E-Bit Count 2 Status 1 Status 2 Receive Information Receive Control 1 Receive Control 2 Transmit Control 1 Transmit Control 2 Common Control 1 Test 1 Interrupt Mask 1 Interrupt Mask 2 Line Interface Control Test 2 Common Control 2 Common Control 3 Synchronizer Status Receive Non-Align Frame Transmit Signaling 1 Transmit Signaling 2 Transmit Signaling 3 Transmit Signaling 4 Transmit Signaling 5 Transmit Signaling 6 Transmit Signaling 7 Transmit Signaling 8 Transmit Signaling 9 Transmit Signaling 10 Transmit Signaling 11 Transmit Signaling 12 Transmit Signaling 13 Transmit Signaling 14 Transmit Signaling 15 Transmit Signaling 16 ADDRESS 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2E 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R R R R R R R R R R R R R R R R R REGISTER NAME Transmit Align Frame Transmit Non-Align Frame Transmit Channel Blocking 1 Transmit Channel Blocking 2 Transmit Channel Blocking 3 Transmit Channel Blocking 4 Transmit Idle 1 Transmit Idle 2 Transmit Idle 3 Transmit Idle 4 Transmit Idle Definition Receive Channel Blocking 1 Receive Channel Blocking 2 Receive Channel Blocking 3 Receive Channel Blocking 4 Receive Align Frame Receive Signaling 1 Receive Signaling 2 Receive Signaling 3 Receive Signaling 4 Receive Signaling 5 Receive Signaling 6 Receive Signaling 7 Receive Signaling 8 Receive Signaling 9 Receive Signaling 10 Receive Signaling 11 Receive Signaling 12 Receive Signaling 13 Receive Signaling 14 Receive Signaling 15 Receive Signaling 16 Note: Test Registers 1 and 2 are used only by the factory; these registers must be cleared (set to all 0s) on power-up initialization to ensure proper operation. 8 of 60 DS2153Q 3 PARALLEL PORT The DS2153Q is controlled via a multiplexed bidirectional address/data bus by an external microcontroller or microprocessor. The DS2153Q can operate with either Intel or Motorola bus timing configurations. If the BTS pin is tied low, Intel timing will be selected; if tied high, Motorola timing will be selected. All Motorola bus signals are listed in parentheses (). See the timing diagrams in Section 14 for more details. The multiplexed bus on the DS2153Q saves pins because the address information and data information share the same signal paths. The addresses are presented to the pins in the first portion of the bus cycle and data will be transferred on the pins during second portion of the bus cycle. Addresses must be valid prior to the falling edge of ALE (AS), at which time the DS2153Q latches the address from the AD0 to AD7 pins. Valid write data must be present and held stable during the later portion of the DS or WR pulses. In a read cycle, the DS2153Q outputs a byte of data during the latter portion of the DS or RD pulses. The read cycle is terminated and the bus returns to a high-impedance state as RD transitions high in Intel timing or as DS transitions low in Motorola timing. 9 of 60 DS2153Q 4 CONTROL AND TEST REGISTERS The operation of the DS2153Q is configured via a set of seven registers. Typically, the control registers are only accessed when the system is first powered up. Once the DS2153Q has been initialized, the control registers only need to be accessed when there is a change in the system configuration. There are two Receive Control Registers (RCR1 and RCR2), two Transmit Control Registers (TCR1 and TCR2), and three Common Control Registers (CCR1, CCR2, and CCR3). Each of the seven registers is described in this section. The LICR is described in Section 13. The Test Registers at addresses 15 and 19 hex are used by the factory in testing the DS2153Q. On powerup, the Test Registers should be set to 00 hex in order for the DS2153Q to operate properly. RCR1: RECEIVE CONTROL REGISTER 1 (Address = 10B Hex) (MSB) RSMF RSM RSIO — — FRC SYNCE (LSB) RESYNC SYMBOL POSITION NAME AND DESCRIPTION RSMF RCR1.7 RSYNC Multiframe Function. Only used if the RSYNC pin is programmed in the multiframe mode (RCR1.6 = 1). 0 = RSYNC outputs CAS multiframe boundaries 1 = RSYNC outputs CRC4 multiframe boundaries RSM RCR1.6 RSYNC Mode Select. 0 = frame mode (see the timing in Section 14) 1 = multiframe mode (see the timing in Section 14) RSIO RCR1.5 RSYNC I/O Select. 0 = RSYNC is an output (depends on RCR1.6) 1 = RSYNC is an input (only valid if elastic store enabled) (Note: this bit must be set to 0 when RCR2.1 = 0) — RCR1.4 Not Assigned. Should be set to 0 when written. — RCR1.3 Not Assigned. Should be set to 0 when written. FRC RCR1.2 Frame Resync Criteria. 0 = resync if FAS received in error 3 consecutive times 1 = resync if FAS or bit 2 of non-FAS is received in error 3 consecutive times SYNCE RCR1.1 Sync Enable. 0 = auto resync enabled 1 = auto resync disabled RESYNC RCR1.0 Resync. When toggled from low to high, a resync is initiated. Must be cleared and set again for a subsequent resync. 10 of 60 DS2153Q Table 4-1. Sync/Resync Criteria FRAME OR MULTIFRAME LEVEL FAS CRC4 SYNC CRITERIA FAS present in frames N and N + 2, and FAS not present in frame N + 1. Two valid MF alignment words found within 8ms. RESYNC CRITERIA ITU SPEC Three consecutive incorrect FAS received. G.706 Alternate (RCR1.2 = 1) the above criteria is met or three consecutive incorrect bit 2 of non-FAS received. 4.1.1 915 or more CRC4 codewords out of 1000 received in error. G.706 4.1.2 4.2 4.3.2 CAS Valid MF alignment word found and previous time slot 16 contains code other than all 0s. Two consecutive MF alignment words received in error. G.732 5.2 RCR2: RECEIVE CONTROL REGISTER 2 (Address = 11 Hex) (MSB) Sa8S Sa7S Sa6S Sa5S Sa4S RSCLKM RESE (LSB) — SYMBOL POSITION NAME AND DESCRIPTION Sa8S RCR2.7 Sa8 Bit Select. Set to 1 to report the Sa8 bit at the RLINK pin; set to 0 to not report the Sa8 bit. Sa7S RCR2.6 Sa7 Bit Select. Set to 1to report the Sa7 bit at the RLINK pin; set to 0 to not report the Sa7 bit. Sa6S RCR2.5 Sa6 Bit Select. Set to 1 to report the Sa6 bit at the RLINK pin; set to 0 to not report the Sa6 bit. Sa5S RCR2.4 Sa5 Bit Select. Set to 1 to report the Sa5 bit at the RLINK pin; set to 0 to not report the Sa5 bit. Sa4S RCR2.3 Sa4 Bit Select. Set to 1 to report the Sa4 bit at the RLINK pin; set to 0 to not report the Sa4 bit. RSCLKM RCR2.2 Receive Side SYSCLK Mode Select. 0 = if SYSCLK is 1.544MHz 1 = if SYSCLK is 2.048MHz RESE RCR2.1 Receive Side Elastic Store Enable. 0=elastic store is bypassed 1=elastic store is enabled — RCR2.0 Not Assigned. Should be set to 0 when written. 11 of 60 DS2153Q TCR1: TRANSMIT CONTROL REGISTER 1 (Address = 12 Hex) (MSB) — TFPT T16S TUA1 TSiS TSA1 TSM (LSB) TSIO SYMBOL POSITION NAME AND DESCRIPTION — TCR1.7 Not Assigned. Should be set to 0 when written to. TFPT TCR1.6 Transmit Time Slot 0 Pass Through. 0 = FAS bits/Sa bits/Remote Alarm sourced internally from the TAF and TNAF registers 1 = FAS bits/Sa bits/Remote Alarm sourced from TSER T16S TCR1.5 Transmit Time Slot 16 Data Select. 0 = sample time slot 16 at TSER pin 1 = source time slot 16 from TS1 to TS16 registers TUA1 TCR1.4 Transmit Unframed All Ones. 0 = transmit data normally 1 = transmit an unframed all ones code at TPOS and TNEG TSiS TCR1.3 Transmit International Bit Select. 0 = sample Si bits at TSER pin 1 = source Si bits from TAF and TNAF registers (in this mode, TCR1.6 must be set to 0) TSA1 TCR1.2 Transmit Signaling All Ones. 0 = normal operation 1 = force time slot 16 in every frame to all ones TSM TCR1.1 TSYNC Mode Select. 0 = frame mode (see the timing in Section 14) 1 = CAS and CRC4 multiframe mode (see the timing in Section 14) TSIO TCR1.0 TSYNC I/O Select. 0 = TSYNC is an input 1 = TSYNC is an output Note: For details about how the Transmit Control Registers affect the operation of the DS2153Q, see Figure 14-9. 12 of 60 DS2153Q TCR2: TRANSMIT CONTROL REGISTER 2 (Address = 13 Hex) (MSB) Sa8S Sa7S Sa6S Sa5S Sa4S — AEBE (LSB) P16F SYMBOL POSITION NAME AND DESCRIPTION Sa8S TCR2.7 Sa8 Bit Select. Set to 1 to source the Sa8 bit from the TLINK pin; set to 0 to not source the Sa8 bit. Sa7S TCR2.6 Sa7 Bit Select. Set to 1 to source the Sa7 bit from the TLINK pin; set to 0 to not source the Sa7 bit. Sa6S TCR2.5 Sa6 Bit Select. Set to 1 to source the Sa6 bit from the TLINK pin; set to 0 to not source the Sa6 bit. Sa5S TCR2.4 Sa5 Bit Select. Set to 1 to source the Sa5 bit from the TLINK pin; set to 0 to not source the Sa5 bit. Sa4S TCR2.3 Sa4 Bit Select. Set to 1 to source the Sa4 bit from the TLINK pin; set to 0 to not source the Sa4 bit. — TCR2.2 Not Assigned. Should be set to 0 when written. AEBE TCR2.1 Automatic E-Bit Enable. 0 = E-bits not automatically set in the transmit direction 1 = E-bits automatically set in the transmit direction P16F TCR2.0 Function of Pin 16. 0 = Receive Loss of Sync (RLOS) 1 = Loss of Transmit Clock (LOTC) 13 of 60 DS2153Q CCR1: COMMON CONTROL REGISTER 1 (Address = 14 Hex) (MSB) FLB THDB3 TG802 TCRC4 RSM RHDB3 RG802 (LSB) RCRC4 SYMBOL POSITION NAME AND DESCRIPTION FLB CCR1.7 Framer Loopback. 0 = loopback disabled 1 = loopback enabled THDB3 CCR1.6 Transmit HDB3 Enable. 0 = HDB3 disabled 1 = HDB3 enabled TG802 CCR1.5 Transmit G.802 Enable. See Figure 14-7 for details. 0 = do not force TCHBLK high during bit 1 of time slot 26 1 = force TCHBLK high during bit 1 of time slot 26 TCRC4 CCR1.4 Transmit CRC4 Enable. 0 = CRC4 disabled 1 = CRC4 enabled RSM CCR1.3 Receive Signaling Mode Select. 0 = CAS signaling mode 1 = CCS signaling mode RHDB3 CCR1.2 Receive HDB3 Enable. 0 = HDB3 disabled 1 = HDB3 enabled RG802 CCR1.1 Receive G.802 Enable. See Figure 14-7 for details. 0 = do not force RCHBLK high during bit 1 of time slot 26 1 = force RCHBLK high during bit 1 of time slot 26 RCRC4 CCR1.0 Receive CRC4 Enable. 0 = CRC4 disabled 1 = CRC4 enabled 14 of 60 DS2153Q CCR2: COMMON CONTROL REGISTER 2 (Address = 1A Hex) (MSB) ECUS VCRFS AAIS ARA RSERC LOTCMC RLB (LSB) LLB SYMBOL POSITION NAME AND DESCRIPTION ECUS CCR2.7 Error Counter Update Select. 0 = update error counters once a second 1 = update error counters every 62.5ms (500 frames) VCRFS CCR2.6 VCR Function Select. 0 = count Bipolar Violations (BPVs) 1 = count Code Violations (CVs) AAIS CCR2.5 Automatic AIS Generation. 0 = disabled 1 = enabled ARA CCR2.4 Automatic Remote Alarm Generation. 0 = disabled 1 = enabled RSERC CCR2.3 RSER Control. 0 = allow RSER to output data as received under all conditions 1 = force RSER to 1 under loss of frame alignment conditions LOTCMC CCR2.2 Loss of Transmit Clock Mux Control. Determines whether the transmit side formatter should switch to the ever present RCLK if the TCLK should fail to transition (see Figure 1-1). 0 = do not switch to RCLK if TCLK stops 1 = switch to RCLK if TCLK stops RLB CCR2.1 Remote Loopback. 0 = loopback disabled 1 = loopback enabled LLB CCR2.0 Local Loopback. 0 = loopback disabled 1 = loopback enabled 15 of 60 DS2153Q CCR3: COMMON CONTROL REGISTER 3 (Address = 1B Hex) (MSB) TESE TCBFS TIRFS ESR LIRST — TSCLKM (LSB) — SYMBOL POSITION NAME AND DESCRIPTION TESE CCR3.7 Transmit Elastic Store Enable. 0 = elastic store is disabled 1 = elastic store is enabled TCBFS CCR3.6 Transmit Channel Blocking Registers (TCBR) Function Select. 0 = TCBRs define the operation of the TCHBLK output pin 1 = TCBRs define which signaling bits are to be inserted TIRFS CCR3.5 Transmit Idle Registers (TIR) Function Select. 0 = TIRs define in which channels to insert idle code 1 = TIRs define in which channels to insert data from RSER ESR CCR3.4 Elastic Stores Reset. Setting this bit from a 1 to a 0 will force the elastic stores to a known depth. Should be toggled after SYSCLK has been applied and is stable. Must be set and cleared again for a subsequent reset. Do not leave this bit set high. LIRST CCR3.3 Line Interface Reset. Setting this bit from a 0 to a 1 will initiate an internal reset that affects the slicer, AGC, clock recovery state machine, and jitter attenuator. Normally this bit is only toggled on power-up. Must be cleared and set again for a subsequent reset. — CCR3.2 Not Assigned. Should be set to 0 when written. TSCLKM CCR3.1 Transmit Backplane Clock Select. Must be set like RCR2.2. 0 = 1.544MHz 1 = 2.048MHz — CCR3.0 Not Assigned. Should be set to 0 when written. 16 of 60 DS2153Q 4.1 Local Loopback When CCR2.0 is set to a 1, the DS2153Q will be forced into Local Loopback (LLB). In this loopback, data will continue to be transmitted as normal through the transmit side of the SCT. Data being received at RTIP and RRING will be replaced with the data being transmitted. Data in this loopback will pass through the jitter attenuator. See Figure 1-1 for more details. 4.2 Remote Loopback When CCR2.1 is set to a 1, the DS2153Q will be forced into Remote Loopback (RLB). In this loopback, data recovered off the E1 line from the RTIP and RRING pins will be transmitted back onto the E1 line (with any BPVs that might have occurred intact) via the TTIP and TRING pins. Data will continue to pass through the receive side of the DS2153Q as it would normally and the data at the TSER input will be ignored. Data in this loopback will pass through the jitter attenuator. See Figure 1-1 for more details. 4.3 Framer Loopback When CCR1.7 is set to a 1, the DS2153Q will enter a Framer Loopback (FLB) mode. This loopback is useful in testing and debugging applications. In FLB, the DS2153Q will loop data from the transmit side back to the receive side. When FLB is enabled, the following will occur: 1) Data will be transmitted at TTIP and TRING. 2) Data off the E1 line at RTIP and RRING will be ignored. The RCLK output will be replaced with the TCLK input. 4.4 Automatic Alarm Generation When either CCR2.4 or CCR2.5 is set to 1, the DS2153Q monitors the receive side to determine if any of the following conditions are present: loss of receive frame synchronization, AIS alarm (all 1s) reception, or loss of receive carrier (or signal). If any one (or more) of the above conditions is present, then the DS2153Q will either force an AIS alarm (if CCR2.5 = 1) or a Remote Alarm (CCR2.4 = 1) to be transmitted via the TTIP and TRING pins. It is an illegal state to have both CCR2.4 and CCR2.5 set to 1 at the same time. 4.5 Power-Up Sequence On power-up, after the supplies are stable, the DS2153Q should be configured for operation by writing to all of the internal registers (this includes setting the Test Register) since the contents of the internal registers cannot be predicted on power-up. Next, the LIRST bit should be toggled from 0 to 1 to reset the line interface circuitry (it will take the DS2153Q about 40ms to recover from the LIRST being toggled). Finally, after the SYSCLK input is stable, the ESR bit should be toggled from a 0 to a 1 and back to 0 (this step can be skipped if the elastic stores are disabled). 17 of 60 DS2153Q 5 STATUS AND INFORMATION REGISTERS There is a set of four registers that contain information on the current real-time status of the DS2153Q: Status Register 1 (SR1), Status Register 2 (SR2), Receive Information Register (RIR), and Synchronizer Status Register (SSR). When a particular event has occurred (or is occurring), the appropriate bit in one of these four registers will be set to a 1. All of the bits in these registers operate in a latched fashion (except for the SSR). This means that if an event occurs and a bit is set to a 1 in any of the registers, it will remain set until the user reads that bit. The bit will be cleared when it is read and it will not be set again until the event has occurred again or if the alarm is still present. The user will always precede a read of the SR1, SR2, and RIR registers with a write. The byte written to the register will inform the DS2153Q which bits the user wishes to read and have cleared. The user will write a byte to one of these three registers, with a 1 in the bit positions he or she wishes to read and a 0 in the bit positions he or she does not wish to obtain the latest information on. When a 1 is written to a bit location, the read register will be updated with current value and it will be cleared. When a 0 is written to a bit position, the read register will not be updated and the previous value will be held. A write to the status and information registers will be immediately followed by a read of the same register. The read result should be logically ANDed with the mask byte that was just written and this value should be written back into the same register to insure that bit does indeed clear. This second write step is necessary because the alarms and events in the status registers occur asynchronously in respect to their access via the parallel port. This write-read-write scheme allows an external microcontroller or microprocessor to individually poll certain bits without disturbing the other bits in the register. This operation is key in controlling the DS2153Q with higher-order software languages. The SSR register operates differently than the other three. It is a read-only register and it reports the status of the synchronizer in real time. This register is not latched and it is not necessary to precede a read of this register with a write. The SR1 and SR2 registers have the unique ability to initiate a hardware interrupt via the INT1 and INT2 pins, respectively. Each of the alarms and events in the SR1 and SR2 can be either masked or unmasked from the interrupt pins via the Interrupt Mask Register 1 (IMR1) and Interrupt Mask Register 2 (IMR2), respectively. 18 of 60 DS2153Q RIR: RECEIVE INFORMATION REGISTER (Address = 08 Hex) (MSB) TESF TESE JALT RESF RESE CRCRC FASRC (LSB) CASRC SYMBOL POSITION NAME AND DESCRIPTION TESF RIR.7 Transmit Elastic Store Full. Set when the elastic store fills and a frame is deleted. TESE RIR.6 Transmit Elastic Store Empty. Set when the elastic store empties and a frame is repeated. JALT RIR.5 Jitter Attenuator Limit Trip. Set when the jitter attenuator FIFO reaches to within 4 bits of its limit; useful for debugging jitter attenuation operation. RESF RIR.4 Elastic Store Full. Set when the elastic store buffer fills and a frame is deleted. RESE RIR.3 Elastic Store Empty. Set when the elastic store buffer empties and a frame is repeated. CRCRC RIR.2 CRC Resync Criteria Met. Set when 915/1000 codewords are received in error. FASRC RIR.1 FAS Resync Criteria Met. Set when three consecutive FAS words are received in error. CASRC RIR.0 CAS Resync Criteria Met. Set when two consecutive CAS MF alignment words are received in error. 19 of 60 DS2153Q SSR: SYNCHRONIZER STATUS REGISTER (Address = 1E Hex) (MSB) CSC5 CSC4 CSC3 CSC2 CSC0 FASSA CASSA (LSB) CRC4SA SYMBOL POSITION NAME AND DESCRIPTION CSC5 SSR.7 CRC4 Sync Counter Bit 5. MSB of the 6-bit counter. CSC4 SSR.6 CRC4 Sync Counter Bit 4. CSC3 SSR.5 CRC4 Sync Counter Bit 3. CSC2 SSR.4 CRC4 Sync Counter Bit 2. CSC0 SSR.3 CRC4 Sync Counter Bit 0. LSB of the 6-bit counter. The next to LSB bit is not accessible. This bit will toggle each time the CRC4 MF search times out at 8ms. FASSA SSR.2 FAS Sync Active. Set while the synchronizer is searching for alignment at the FAS level. CASSA SSR.1 CAS MF Sync Active. Set while the synchronizer is searching for the CAS MF alignment word. CRC4SA SSR.0 CRC4 MF Sync Active. Set while the synchronizer is searching for the CRC4 MF alignment word. 5.1 CRC4 Sync Counter The CRC4 sync counter increments each time the 8ms CRC4 multiframe search times out. The counter is cleared when the DS2153Q has successfully obtained synchronization at the CRC4 level. The counter can also be cleared by disabling the CRC4 mode (CCR1.0 = 0). This counter is useful for determining the amount of time the DS2153Q has been searching for synchronization at the CRC4 level. Annex B of CCITT G.706 suggests that if synchronization at the CRC4 level cannot be obtained within 400ms, then the search should be abandoned and proper action taken. The CRC4 sync counter will rollover. 20 of 60 DS2153Q SR1: STATUS REGISTER 1 (Address = 06 Hex) (MSB) RSA1 RDMA RSA0 RSLIP RUA1 RRA RCL (LSB) RLOS SYMBOL POSITION NAME AND DESCRIPTION RSA1 SR1.7 Receive Signaling All 1s. Set when the contents of time slot 16 contains less than three 0s over 16 consecutive frames. This alarm is not disabled in the CCS signaling mode. RDMA SR1.6 Receive Distant MF Alarm. Set when bit 6 of time slot 16 in frame 0 has been set for two consecutive multiframes. This alarm is not disabled in the CCS signaling mode. RSA0 SR1.5 Receive Signaling All 0s. Set when over a full MF, time slot 16 contains all 0s. RSLIP SR1.4 Receive Elastic Store Slip Occurrence. Set when the elastic store has either repeated or deleted a frame of data. RUA1 SR1.3 Receive Unframed All 1s. Set when an unframed all 1s code is received at RTIP and RRING. RRA SR1.2 Receive Remote Alarm. Set when a remote alarm is received at RTIP and RRING. RCL SR1.1 Receive Carrier Loss. Set when 255 consecutive 0s have been detected at RTIP and RRING. RLOS SR1.0 Receive Loss of Sync. Set when the device is not synchronized to the receive E1 stream. 21 of 60 DS2153Q Table 5-1. Alarm Set and Clear Criteria ALARM RSA1 (receive signaling all 1s) RSA0 (receive signaling all 0s) RDMA (receive distant multiframe alarm) RUA1 (receive unframed all 1s) RRA (receive remote alarm) RCL CCITT SPEC. SET CRITERIA CLEAR CRITERIA Over 16 consecutive frames (one full MF) time slot 16 contains less than three 0s Over 16 consecutive frames (one full MF) time slot 16 contains three or more 0s Over 16 consecutive frames (one full MF) time slot 16 contains all 0s Over 16 consecutive frames (one full MF) time slot 16 contains at least a single 1 Bit 6 in time slot 16 of frame 0 set to 1 for two consecutive MF Bit 6 in time slot 16 of frame 0 set to 0 for a two consecutive MF O.162 Less than three 0s in two frames (512 bits) More than two 0s in two frames (512 bits) O.162 Bit 3 of non-align frame set to 1 for three consecutive occasions Bit 3 of non-align frame set to 0 for three consecutive occasions 255 consecutive 0s received In 255-bit times, at least 32 1s are received (receive carrier loss) 22 of 60 G.732 4.2 G.732 5.2 2.1.5 1.6.1.2 O.162 2.1.4 G.775 DS2153Q SR2: STATUS REGISTER 2 (Address = 07 Hex) (MSB) RMF RAF TMF SEC TAF LOTC RCMF (LSB) TSLIP SYMBOL POSITION NAME AND DESCRIPTION RMF SR2.7 Receive CAS Multiframe. Set every 2ms (regardless if CAS signaling is enabled or not) on receive multiframe boundaries. Used to alert the host that signaling data is available. RAF SR2.6 Receive Align Frame. Set every 250ms at the beginning of align frames. Used to alert the host that Si and Sa bits are available in the RAF and RNAF registers. TMF SR2.5 Transmit Multiframe. Set every 2µs (regardless if CRC4 is enabled) on transmit multiframe boundaries. Used to alert the host that signaling data needs to be updated. SEC SR2.4 1-Second Timer. Set on increments of 1 second based on RCLK. If CCR2.7 = 1, then this bit will be set every 62.5ms instead of once a second. TAF SR2.3 Transmit Align Frame. Set every 250µs at the beginning of align frames. Used to alert the host that the TAF and TNAF registers need to be updated. LOTC SR2.2 Loss of Transmit Clock. Set when the TCLK pin has not transitioned for one channel time (or 3.9µs). Will force pin 16 high if enabled via TCR2.0. Based on RCLK. RCMF SR2.1 Receive CRC4 Multiframe. Set on CRC4 multiframe boundaries; will continue to be set every 2ms on an arbitrary boundary if CRC4 is disabled. TSLIP SR2.0 Transmit Elastic Store Slip. Set when the elastic store has either repeated or deleted a frame of data. 23 of 60 DS2153Q IMR1: INTERRUPT MASK REGISTER1 (Address = 16 Hex) (MSB) RSA1 RDMA RSA0 RSLIP RUA1 RRA SYMBOL POSITION NAME AND DESCRIPTION RSA1 IMR1.7 Receive Signaling All 1s. 0 = interrupt masked 1 = interrupt enabled RDMA IMR1.6 Receive Distant MF Alarm. 0 = interrupt masked 1 = interrupt enabled RSA0 IMR1.5 Receive Signaling All 0s. 0 = interrupt masked 1 = interrupt enabled RSLIP IMR1.4 Receive Elastic Store Slip Occurrence. 0 = interrupt masked 1 = interrupt enabled RUA1 IMR1.3 Receive Unframed All 1s. 0 = interrupt masked 1 = interrupt enabled RRA IMR1.2 Receive Remote Alarm. 0 = interrupt masked 1 = interrupt enabled RCL IMR1.1 Receive Carrier Loss. 0 = interrupt masked 1 = interrupt enabled RLOS IMR1.0 Receive Loss of Sync. 0 = interrupt masked 1 = interrupt enabled 24 of 60 RCL (LSB) RLOS DS2153Q IMR2: INTERRUPT MASK REGISTER 2 (Address = 17 Hex) (MSB) RMF RAF SYMBOL POSITION RMF IMR2.7 Receive CAS Multiframe. 0 = interrupt masked 1 = interrupt enabled RAF IMR2.6 Receive Align Frame. 0 = interrupt masked 1 = interrupt enabled TMF IMR2.5 Transmit Multiframe. 0 = interrupt masked 1 = interrupt enabled SEC IMR2.4 1-Second Timer. 0 = interrupt masked 1 = interrupt enabled TAF IMR2.3 Transmit Align Frame. 0 = interrupt masked 1 = interrupt enabled LOTC IMR2.2 Loss Of Transmit Clock. 0 = interrupt masked 1 = interrupt enabled RCMF IMR2.1 Receive CRC4 Multiframe. 0 = interrupt masked 1 = interrupt enabled TSLIP IMR2.0 Transmit Side Elastic Store Slip. 0 = interrupt masked 1 = interrupt enabled TMF SEC TAF NAME AND DESCRIPTION 25 of 60 LOTC RCMF (LSB) TSLIP DS2153Q 6 ERROR COUNT REGISTERS There are a set of four counters in the DS2153Q that record bipolar or code violations, errors in the CRC4 SMF codewords, E bits as reported by the far end, and word errors in the FAS. Each of these four counters are automatically updated on either 1-second boundaries (CCR2.7 = 0) or every 62.5ms (CCR2.7 = 1) as determined by the timer in Status Register 2 (SR2.4). Hence, these registers contain performance data from either the previous second or the previous 62.5ms. The user can use the interrupt from the timer to determine when to read these registers. The user has a full second (or 62.5ms) to read the counters before the data is lost. 6.1 BPV or Code Violation Counter Violation Count Register 1 (VCR1) is the most significant word and VCR2 is the least significant word of a 16-bit counter that records either Bipolar Violations (BPVs) or Code Violations (CVs). If CCR2.6 = 0, then the VCR counts bipolar violations. Bipolar violations are defined as consecutive marks of the same polarity. In this mode, if the HDB3 mode is set for the receive side via CCR1.2, then HDB3 codewords are not counted as BPVs. If CCR2.6 = 1, then the VCR counts code violations as defined in CCITT O.161. Code violations are defined as consecutive bipolar violations of the same polarity. In most applications, the DS2153Q should be programmed to count BPVs when receiving AMI code and to count CVs when receiving HDB3 code. This counter increments at all times and is not disabled by loss of sync conditions. The counter saturates at 65,535 and will not rollover. The bit error rate on an E1 line would have to be greater than 10**-2 before the VCR would saturate. VCR1: UPPER BIPOLAR VIOLATION COUNT REGISTER 1 (Address = 00 Hex) VCR2: LOWER BIPOLAR VIOLATION COUNT REGISTER 2 (Address = 01 Hex) (MSB) V15 V14 V13 V12 V11 V10 V7 V6 V5 V4 V3 V2 V9 (LSB) V8 VCR1 V1 V0 VCR2 SYMBOL POSITION NAME AND DESCRIPTION V15 VCR1.7 MSB of the 16-bit bipolar or code violation count. V0 VCR2.0 LSB of the 16-bit bipolar or code violation count. 26 of 60 DS2153Q 6.2 CRC4 Error Counter CRC4 Count Register 1 (CRCCR1) is the most significant word and CRCCR2 is the least significant word of a 10-bit counter that records word errors in the Cyclic Redundancy Check 4 (CRC4). Since the maximum CRC4 count in a 1-second period is 1000, this counter cannot saturate. The counter is disabled during loss of sync at either the FAS or CRC4 level; it will continue to count if loss of multiframe sync occurs at the CAS level. CRCCR1: CRC4 COUNT REGISTER 1 (Address = 02 Hex) CRCCR2: CRC4 COUNT REGISTER 2 (Address = 03 Hex) (MSB) (See note) (See note) (See note) (See note) (See note) (See note) CRC9 (LSB) CRC8 CRC7 CRC6 CRC5 CRC4 CRC3 CRC2 CRC1 CRC0 SYMBOL POSITION NAME AND DESCRIPTION CRC9 CRCCR1.1 MSB of the 10-bit CRC4 error count. CRC0 CRCCR2.0 LSB of the 10-bit CRC4 error count. CRCCR1 CRCCR2 Note: The upper 6 bits of CRCCR1 at address 02 are the most significant bits of the 12-bit FAS error counter. 6.3 E-Bit Counter E-bit Count Register 1 (EBCR1) is the most significant word and EBCR2 is the least significant word of a 10-bit counter that records Far End Block Errors (FEBE) as reported in the first bit of frames 13 and 15 on E1 lines running with CRC4 multiframe. These count registers will increment once each time the received E-bit is set to 0. Since the maximum E-bit count in a 1-second period is 1000, this counter cannot saturate. The counter is disabled during loss of sync at either the FAS or CRC4 level; it will continue to count if loss of multiframe sync occurs at the CAS level. EBCR1: E-BIT COUNT REGISTER 1 (Address = 04 Hex) EBCR2: E-BIT COUNT REGISTER 2 (Address = 05 Hex) (MSB) (See note) (See note) (See note) (See note) (See note) (See note) EB9 (LSB) EB8 EB7 EB6 EB5 EB4 EB3 EB2 EB1 EB0 SYMBOL POSITION NAME AND DESCRIPTION EB9 EBCR1.1 MSB of the 10-bit E-bit count. EB0 EBCR2.0 LSB of the 10-bit E-bit count. Note: The upper 6 bits of EBCR1 at address 04 are the least significant bits of the 12-bit FAS error counter. 27 of 60 EBCR1 EBCR2 DS2153Q 6.4 FAS Bit Error Counter FAS Count Register 1 (FASCR1) is the most significant word and FASCR2 is the least significant word of a 12-bit counter that records word errors in the Frame Alignment Signal in time slot 0. This counter is disabled during loss of synchronization conditions, (RLOS = 1). Since the maximum FAS word error count in a 1-second period is 4000, this counter cannot saturate. FASCR1: FAS BIT COUNT REGISTER 1 (Address = 02 Hex) FASCR2: FAS BIT COUNT REGISTER 2 (Address = 04 Hex) (MSB) FAS11 FAS10 FAS9 FAS8 FAS7 FAS6 FAS5 FAS4 FAS3 FAS2 FAS1 FAS0 (Note 1) (LSB) (Note 1) FASCR1 (Note 2) (Note 2) FASCR2 SYMBOL POSITION NAME AND DESCRIPTION FAS11 FASCR1.7 MSB of the 12-bit FAS error count. FAS0 FASCR2.2 LSB of the 12-bit FAS error count. Note 1: The lower 2 bits of FASCR1 at address 02 are the most significant bits of the 10-bit CRC4 error counter. Note 2: The lower 2 bits of FASCR2 at address 04 are the most significant bits of the 10-bit E-bit counter. 28 of 60 DS2153Q 7 Sa DATA LINK CONTROL AND OPERATION The DS2153Q provides for access to the proposed E1 performance monitor data link in the Sa bit positions. The device allows access to the Sa bits either via a set of two internal registers (RNAF and TNAF) or via two external pins (RLINK and TLINK). On the receive side, the Sa bits are always reported in the internal RNAF register (see Section 12 for more details). All five Sa bits are always output at the RLINK pin. See Section 14 for detailed timing. Via RCR2, the user can control the RLCLK pin to pulse during any combination of Sa bits. This allows the user to create a clock that can be used to capture the needed Sa bits. On the transmit side, the individual Sa bits can be either sourced from the internal TNAF register (TCR1.6 = 0) or from the external TLINK pin. Via TCR2, the DS2153Q can be programmed to source any combination of the additional bits from the TLINK pin. If the user wishes to pass the Sa bits through the DS2153Q without them being altered, then the device should be set up to source all five Sa bits via the TLINK pin and the TLINK pin should be tied to the TSER pin. See the timing diagrams and the transmit data flow diagram in Section 14 for examples. 29 of 60 DS2153Q 8 SIGNALING OPERATION The Channel Associated Signaling (CAS) bits embedded in the E1 stream can be extracted from the receive stream and inserted into the transmit stream by the DS2153Q. Each of the 30 channels has four signaling bits (A/B/C/D) associated with it. The numbers in parentheses are the channel associated with a particular signaling bit. The channel numbers have been assigned as described in the ITU documents. For example, channel 1 is associated with time slot 1 and channel 30 is associated with time slot 31. There is a set of 16 registers for the receive side (RS1 to RS16) and 16 registers on the transmit side (TS1 to TS16). The signaling registers are detailed below. RS1 TO RS16: RECEIVE SIGNALING REGISTERS (Address = 30 to 3F Hex) (MSB) (LSB) 0 0 0 0 X Y X X RS1 (30) A(1) B(1) C(1) D(1) A(16) B(16) C(16) D(16) RS2 (31) A(2) B(2) C(2) D(2) A(17) B(17) C(17) D(17) RS3 (32) A(3) B(3) C(3) D(3) A(18) B(18) C(18) D(18) RS4 (33) A(4) B(4) C(4) D(4) A(19) B(19) C(19) D(19) RS5 (34) A(5) B(5) C(5) D(5) A(20) B(20) C(20) D(20) RS6 (35) A(6) B(6) C(6) D(6) A(21) B(21) C(21) D(21) RS7 (33) A(7) B(7) C(7) D(7) A(22) B(22) C(22) D(22) RS8 (37) A(8) B(8) C(8) D(8) A(23) B(23) C(23) D(23) RS9 (38) A(9) B(9) C(9) D(9) A(24) B(24) C(24) D(24) RS10 (39) A(10) B(10) C(10) D(10) A(25) B(25) C(25) D(25) RS11 (3A) A(11) B(11) C(11) D(11) A(26) B(26) C(26) D(26) RS12 (3B) A(12) B(12) C(12) D(12) A(27) B(27) C(27) D(27) RS13 (3C) A(13) B(13) C(13) D(13) A(28) B(28) C(28) D(28) RS14 (3D) A(14) B(14) C(14) D(14) A(29) B(29) C(29) D(29) RS15 (3E) A(15) B(15) C(15) D(15) A(30) B(30) C(30) D(30) RS16 (3F) SYMBOL POSITION NAME AND DESCRIPTION X RS1.0/1/3 Y RS1.2 Remote Alarm Bit (integrated and reported in SR1.6) A(1) RS2.7 Signaling Bit A for Channel 1 D(30) RS16.0 Signaling Bit D for Channel 30 Spare Bits Each Receive Signaling Register (RS1 to RS16) reports the incoming signaling from two time slots. The bits in the Receive Signaling Registers are updated on multiframe boundaries so the user can utilize the Receive Multiframe Interrupt in the Receive Status Register 2 (SR2.7) to know when to retrieve the signaling bits. The user has a full 2ms to retrieve the signaling bits before the data is lost. The RS registers are updated under all conditions. Their validity should be qualified by checking for synchronization at the CAS level. In CCS signaling mode, RS1 to RS16 can also be used to extract signaling information. Via the SR2.7 bit, the user will be informed when the signaling registers have been loaded with data. The user has 2ms to retrieve the data before it is lost. 30 of 60 DS2153Q TS1 TO TS16: TRANSMIT SIGNALING REGISTERS (Address = 40 to 4F Hex) (MSB) (LSB) 0 0 0 0 X Y X X TS1 (40) A(1) B(1) C(1) D(1) A(31) B(16) C(16) D(16) TS2 (41) A(2) B(2) C(2) D(2) A(32) B(17) C(17) D(17) TS3 (42) A(3) B(3) C(3) D(3) A(33) B(18) C(18) D(18) TS4 (43) A(4) B(4) C(4) D(4) A(34) B(19) C(19) D(19) TS5 (44) A(5) B(5) C(5) D(5) A(35) B(20) C(20) D(20) TS6 (45) A(6) B(6) C(6) D(6) A(36) B(21) C(21) D(21) TS7 (43) A(7) B(7) C(7) D(7) A(37) B(22) C(22) D(22) TS8 (47) A(8) B(8) C(8) D(8) A(38) B(23) C(23) D(23) TS9 (48) A(9) B(9) C(9) D(9) A(39) B(24) C(24) D(24) TS10 (49) A(10) B(10) C(10) D(10) A(40) B(25) C(25) D(25) TS11 (4A) A(11) B(11) C(11) D(11) A(41) B(26) C(26) D(26) TS12 (4B) A(12) B(12) C(12) D(12) A(42) B(27) C(27) D(27) TS13 (4C) A(13) B(13) C(13) D(13) A(43) B(28) C(28) D(28) TS14 (4D) A(14) B(14) C(14) D(14) A(44) B(29) C(29) D(29) TS15 (43) A(15) B(15) C(15) D(15) A(45) B(30) C(30) D(30) TS16 (4F) SYMBOL POSITION NAME AND DESCRIPTION X TS1.0/1/3 Y TS1.2 Remote Alarm Bit A(1) TS2.7 Signaling Bit A for Channel 1 D(30) TS16.0 Signaling Bit D for Channel 30 Spare Bits Each Transmit Signaling Register (TS1 to TS16) contains the CAS bits for two time slots that will be inserted into the outgoing stream if enabled to do so via TCR1.5. On multiframe boundaries, the DS2153Q will load the values present in the Transmit Signaling Register into an outgoing signaling shift register that is internal to the device. The user can utilize the Transmit Multiframe bit in Status Register 2 (SR2.5) to know when to update the signaling bits. The bit will be set every 2ms and the user has 2ms to update the TSRs before the old data will be retransmitted. The TS1 register is special because it contains the CAS multiframe alignment word in its upper nibble. The upper nibble must always be set to 0000, or else the terminal at the far end will lose multiframe synchronization. If the user wishes to transmit a multiframe alarm to the far end, then the TS1.2 bit should be set to a 1. If no alarm is to be transmitted, then the TS1.2 bit should be cleared. The three remaining bits in TS1 are the spare bits. If they are not used, they should be set to 1. In CCS signaling mode, TS1 to TS16 can also be used to insert signaling information. Via the SR2.5 bit, the user will be informed when the signaling registers need to be loaded with data. The user has 2ms to load the data before the old data will be retransmitted. Via the CCR3.6 bit, the user has the option to use the Transmit Channel Blocking Registers (TCBRs) to determine on a channel by channel basis which signaling bits are to be inserted via the TSRs (the corresponding bit in the TCBRs = 1) and which are to be sourced from the TSER pin (the corresponding bit in the TCBRs = 0). See the Transmit Data Flow diagram in Section 14 for more details. 31 of 60 DS2153Q 9 TRANSMIT IDLE REGISTERS There is a set of five registers in the DS2153Q that can be used to custom tailor the data that is to be transmitted onto the E1 line, on a channel-by-channel basis. Each of the 32 E1 channels can be forced to have a user-defined idle code inserted into them. TIR1/TIR2/TIR3/TIR4: TRANSMIT IDLE REGISTERS (Address = 26 to 29 Hex) (MSB) (LSB) CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1 TIR1 (26) CH16 CH15 CH14 CH13 CH12 CH11 CH10 CH9 TIR2 (27) CH24 CH23 CH22 CH21 CH20 CH19 CH18 CH17 TIR3 (28) CH32 CH31 CH30 CH29 CH28 CH27 CH26 CH25 TIR4 (29) SYMBOL POSITION NAME AND DESCRIPTION CH32 TIR4.7 Transmit Idle Registers. 0 = do not insert the Idle Code into this channel CH1 TIR1.0 1 = insert the Idle Code into this channel Note: If CCR3.5 = 1, then a 0 in the TIRs implies that channel data is to be sourced from TSER and a 1 implies that channel data is to be sourced from the RSER pin. TIDR: TRANSMIT IDLE DEFINITION REGISTER (Address = 2A Hex) (MSB) TIDR7 TIDR6 SYMBOL TIDR7 TIDR0 TIDR5 TIDR4 POSITION TIDR.7 TIDR.0 TIDR3 TIDR2 TIDR1 (LSB) TIDR0 NAME AND DESCRIPTION MSB of the Idle Code LSB of the Idle Code Each of the bit positions in the Transmit Idle Registers (TIR1/TIR2/TIR3/TIR4) represents a time slot in the outgoing frame. When these bits are set to a 1, the corresponding channel will transmit the Idle Code contained in the Transmit Idle Definition Register (TIDR). In the TIDR, the MSB is transmitted first. Via the CCR3.5 bit, the user has the option to use the TIRs to determine on a channel-by-channel basis, if data from the RSER pin should be substituted for data from the TSER pin. In this mode, if the corresponding bit in the TIRs is set to 1, then data will be sourced from the RSER pin. If the corresponding bit in the TIRs is set to 0, then data for that channel will sourced from the TSER pin. See the Transmit Data Flow diagram in Section 14 for more details. 32 of 60 DS2153Q 10 CLOCK BLOCKING REGISTERS The Receive Channel Blocking Registers (RCBR1/RCBR2/RCBR3/RCBR4) and the Transmit Channel Blocking Registers (TCBR1/TCBR2/TCBR3/TCBR4) control the RCHBLK and TCHBLK pins, respectively. The RCHBLK and TCHCLK pins are user-programmable outputs that can be forced either high or low during individual channels. These outputs can be used to block clocks to a USART or LAPD controller in ISDN-PRI applications. When the appropriate bits are set to a 1, the RCHBLK and TCHCLK pins will be held high during the entire corresponding channel time. See the timing diagrams in Section 14 for an example. The TCBRs have an alternate mode of use. Via the CCR3.6 bit, the user has the option to use the TCBRs to determine on a channel by channel basis, which signaling bits are to be inserted via the TSRs (the corresponding bit in the TCBRs = 1) and which are to be sourced from the TSER pin (the corresponding bit in the TCBR = 0). See the Transmit Data Flow diagram in Section 14 for more details. RCBR1/RCBR2/RCBR3/RCBR4: RECEIVE CHANNEL BLOCKING REGISTERS (Address = 2B to 2E Hex) (MSB) CH8 CH16 CH24 CH32 CH7 CH15 CH23 CH31 CH6 CH14 CH22 CH30 CH5 CH13 CH21 CH29 SYMBOL POSITION CH32 RCBR4.7 CH1 RCBR1.0 CH4 CH12 CH20 CH28 CH3 CH11 CH19 CH27 CH2 CH10 CH18 CH26 (LSB) CH1 CH9 CH17 CH25 RCBR1 (2B) RCBR2 (2C) RCBR3 (2D) RCBR4 (2E) NAME AND DESCRIPTION Receive Channel Blocking Registers. 0 = force the RCHBLK pin to remain low during this channel time 1 = force the RCHBLK pin high during this channel time TCBR1/TCBR2/TCBR3/TCBR4: TRANSMIT CHANNEL BLOCKING REGISTERS (Address = 22 to 25 Hex) (MSB) CH8 CH16 CH24 CH32 CH7 CH15 CH23 CH31 CH6 CH14 CH22 CH30 CH5 CH13 CH21 CH29 SYMBOL POSITION CH32 TCBR4.7 CH1 TCBR1.0 CH4 CH12 CH20 CH28 CH3 CH11 CH19 CH27 CH2 CH10 CH18 CH26 (LSB) CH1 CH9 CH17 CH25 TCBR1 (22) TCBR2 (23) TCBR3 (24) TCBR4 (25) NAME AND DESCRIPTION Transmit Channel Blocking Registers. 0 = force the TCHBLK pin to remain low during this channel time 1 = force the TCHBLK pin high during this channel time Note: If CCR3.6 = 1, then a 0 in the TCBRs implies that signaling data is to be sourced from TSER and a 1 implies that signaling data for that channel is to be sourced from the Transmit Signaling (TS) registers. 33 of 60 DS2153Q TCBR1/TCBR2/TCBR3/TCBR4: DEFINITION WHEN CCR3.6 = 1 (MSB) (LSB) CH20 CH4 CH19 CH3 CH18 CH2 CH17* CH1* TCBR1 CH24 CH8 CH23 CH7 CH22 CH6 CH21 CH5 TCBR2 CH28 CH12 CH27 CH11 CH26 CH10 CH25 CH9 TCBR3 CH32 CH16 CH31 CH15 CH30 CH14 CH29 CH13 TCBR4 *CH1 and CH17 should be set to 1 to allow the internal TS1 register to create the CAS Multiframe Alignment Word and Spare/Remote Alarm bits. 34 of 60 DS2153Q 11 ELASTIC STORES OPERATION The DS2153Q has an on-board two-frame (512 bits) elastic store. This elastic store can be enabled via RCR2.1. If the elastic store is enabled (RCR2.1=1), then the user must provide either a 1.544MHz (RCR2.2 = 0) or 2.048MHz (RCR2.2 = 1) clock at the SYSCLK pin. If the elastic store is enabled, then the user has the option of either providing a frame sync at the RSYNC pin (RCR1.5 = 1) or having the RSYNC pin provide a pulse on frame or multiframe boundaries (RCR1.5 = 0). If the user wishes to obtain pulses at the frame boundary, then RCR1.6 must be set to 0, and if the user wishes to have pulses occur at the multiframe boundary, then RCR1.6 must be set to 1. If the user selects to apply a 1.544MHz clock to the SYSCLK pin, then every fourth channel will be deleted and the F-bit position inserted (forced to 1). Hence channels 1, 5, 9, 13, 17, 21, 25, and 29 (time slots 0, 4, 8, 12, 16, 20, 24, and 28) will be deleted. Also, in 1.544MHz applications, the RCHBLK output will not be active in channels 25 through 32 (or in other words, RCBR4 is not active). See Section 14 for more details. If the 512-bit elastic buffer either fills or empties, a controlled slip will occur. If the buffer empties, then a full frame of data (256 bits) will be repeated at RSER and the SR1.4 and RIR.3 bits will be set to 1. If the buffer fills, then a full frame of data will be deleted and the SR1.4 and RIR.4 bits will be set to 1. 35 of 60 DS2153Q 12 ADDITIONAL (Sa) AND INTERNATIONAL (Si) BIT OPERATION The DS2153Q provides for access to both the Additional (Sa) and International (Si) bits. On the receive side, the RAF and RNAF registers will always report the data as it received in the Additional and International bit locations. The RAF and RNAF registers are updated with the setting of the Receive Align Frame bit in Status Register 2 (SR2.6). The host can use the SR2.6 bit to know when to read the RAF and RNAF registers. It has 250µs to retrieve the data before it is lost. On the transmit side, data is sampled from the TAF and TNAF registers with the setting of the Transmit Align Frame bit in Status Register 2 (SR2.3). The host can use the SR2.3 bit to know when to update the TAF and TNAF registers. It has 250µs to update the data or else the old data will be retransmitted. Data in the Si bit position will be overwritten if either the DS2153Q is programmed: (1) to source the Si bits from the TSER pin, (2) in the CRC4 mode, or (3) have automatic E-bit insertion enabled. Data in the Sa bit position will be overwritten if any of the TCR2.3 to TCR2.7 bits are set to 1. See the register descriptions for TCR1 and TCR2 and the Transmit Data Flow diagram in Section 14 for more details. RAF: RECEIVE ALIGN FRAME REGISTER (Address = 2F Hex) (MSB) Si 0 0 1 1 SYMBOL POSITION NAME AND DESCRIPTION Si RAF.7 International Bit. 0 RAF.6 Frame Alignment Signal Bit. 0 RAF.5 Frame Alignment Signal Bit. 1 RAF.4 Frame Alignment Signal Bit. 1 RAF.3 Frame Alignment Signal Bit. 0 RAF.2 Frame Alignment Signal Bit. 1 RAF.1 Frame Alignment Signal Bit. 1 RAF.0 Frame Alignment Signal Bit. 36 of 60 0 1 (LSB) 1 DS2153Q RNAF: RECEIVE NON-ALIGN FRAME REGISTER (Address = 1F Hex) (MSB) Si 1 A Sa4 Sa5 Sa6 SYMBOL POSITION Si RNAF.7 International Bit. 1 RNAF.6 Frame Non-Alignment Signal Bit. A RNAF.5 Remote Alarm. Sa4 RNAF.4 Additional Bit 4. Sa5 RNAF.3 Additional Bit 5. Sa6 RNAF.2 Additional Bit 6. Sa7 RNAF.1 Additional Bit 7. Sa8 RNAF.0 Additional Bit 8. Sa7 (LSB) Sa8 NAME AND DESCRIPTION TAF: TRANSMIT ALIGN FRAME REGISTER (Address = 20 Hex) (MSB) Si 0 0 1 1 SYMBOL POSITION NAME AND DESCRIPTION Si TAF.7 International Bit. 0 TAF.6 Frame Alignment Signal Bit. 0 TAF.5 Frame Alignment Signal Bit. 1 TAF.4 Frame Alignment Signal Bit. 1 TAF.3 Frame Alignment Signal Bit. 0 TAF.2 Frame Alignment Signal Bit. 1 TAF.1 Frame Alignment Signal Bit. 1 TAF.0 Frame Alignment Signal Bit. 37 of 60 0 1 (LSB) 1 DS2153Q TNAF: TRANSMIT NON-ALIGN FRAME REGISTER (Address = 21 Hex) (MSB) Si 1 A Sa4 Sa5 Sa6 SYMBOL POSITION NAME AND DESCRIPTION Si TNAF.7 International Bit. 1 TNAF.6 Frame Non-Alignment Signal Bit. A TNAF.5 Remote Alarm. Sa4 TNAF.4 Additional Bit 4. Sa5 TNAF.3 Additional Bit 5. Sa6 TNAF.2 Additional Bit 6. Sa7 TNAF.1 Additional Bit 7. Sa8 TNAF.0 Additional Bit 8. 38 of 60 Sa7 (LSB) Sa8 DS2153Q 13 LINE INTERFACE FUNCTIONS The line interface function in the DS2153Q contains three sections: the receiver, which handles clock and data recovery; the transmitter, which waveshapes and drives the T1 line; and the jitter attenuator. Each of these three sections is controlled by the Line Interface Control Register (LICR), which is described below. LICR: LINE INTERFACE CONTROL REGISTER (Address = 18 Hex) (MSB) LB2 LB1 LB0 SYMBOL LB2 EGL JAS JABDS DJA (LSB) TPD LICR POSITION LICR.7 NAME AND DESCRIPTION Line Build-Out Select Bit 2. Sets the transmitter build out; see the Table 13-2. LB1 LICR.6 Line Build-Out Select Bit 1. Sets the transmitter build out; see the Table 13-2. LB0 LICR.5 Line Build-Out Select Bit 0. Sets the transmitter build out; see the Table 13-2. EGL LICR.4 Receive Equalizer Gain Limit. 0 = -12dB 1 = -30dB JAS LICR.3 Jitter Attenuator Select. 0 = place the jitter attenuator on the receive side 1 = place the jitter attenuator on the transmit side JABDS LICR.2 Jitter Attenuator Buffer Depth Select. 0 = 128 bits 1 = 32 bits (use for delay sensitive applications) DJA LICR.1 Disable Jitter Attenuator. 0 = jitter attenuator enabled 1 = jitter attenuator disabled TPD LICR.0 Transmit Power Down. 0 = normal transmitter operation 1 = powers down the transmitter and tri-states the TTIP and TRING pins 39 of 60 DS2153Q 13.1 Receive Clock and Data Recovery The DS2153Q contains a digital clock recovery system. See Figure 1-1 and Figure 13-1 for more details. The DS2153Q couples to the receive E1 twisted pair or coax via a 1:1 transformer. See Table 13-3 for transformer details. The DS2153Q automatically adjusts to the E1 signal being received at the RTIP and RRING pins and can handle E1 twisted pair cables of 0.6mm (22 AWG) from 0 to 1.5km in length. The crystal attached at the XTAL1 and XTAL2 pins is multiplied by 4 via an internal PLL and fed to the clock recovery system. The clock recovery system uses both edges of the clock from the PLL circuit to form a 32 times oversampler that is used to recover the clock and data. This oversampling technique offers outstanding jitter tolerance (see Figure 13-2). Normally, the clock that is output at the RCLK pin is the recovered clock from the E1 AMI waveform presented at the RTIP and RRING inputs. When no AMI signal is present at RTIP and RRING, a Receive Carrier Loss (RCL) condition will occur and the RCLK can be sourced from either the ACLKI pin or from the crystal attached to the XTAL1 and XTAL2 pins. The DS2153Q will sense the ACLKI pin to determine if a clock is present. If no clock is applied to the ACLKI pin, then it should be tied to RVSS to prevent the device from falsely sensing a clock. See Table 13-1. If the jitter attenuator is either placed in the transmit path or is disabled, the RCLK output can exhibit short high cycles of the clock. This is due to the highly oversampled digital clock recovery circuitry. If the jitter attenuator is placed in the receive path (as is the case in most applications), the jitter attenuator restores the RCLK to being close to 50% duty cycle. See the receive AC timing characteristics in Section 16 for more details. Table 13-1. Source of RCLK Upon RCL ACLKI PRESENT? Yes No RECEIVE SIDE JITTER ATTENUATOR ACLKI via the jitter attenuator Centered crystal 40 of 60 TRANSMIT SIDE JITTER ATTENUATOR ACLKI TCLK via the jitter attenuator DS2153Q 13.2 Transmit Waveshaping and Line Driving The DS2153Q uses a set of laser-trimmed delay lines along with a precision digital-to-analog converter (DAC) to create the waveforms that are transmitted onto the E1 line. The waveforms created by the DS2153Q meet the ITU specifications. See Figure 13-3. The user will select which waveform is to be generated by properly programming the L0 to L2 bits in the Line Interface Control Register (LICR). The DS2153Q can set up in a number of various configurations depending on the application. See Table 13-2 and Figure 1-1. Table 13-2. LBO Select in LICR TRANSFORMER RETURN LOSS (dB) Rt (Ω) 75Ω normal 1:1.15 step-up N.M. 0 1 120Ω normal 1:1.15 step-up N.M. 0 1 0 75Ω normal with protection resistors 1:1.15 step-up N.M. 8.2 0 1 1 120Ω normal with protection resistors 1:1.15 step-up N.M. 8.2 1 0 0 75Ω with high return loss 1:1.15 step-up 21 27 1 1 0 75Ω with high return loss 1:1.36 step-up 21 18 1 0 0 120Ω with high return loss 1:1.36 step-up 21 27 L2 L1 L0 0 0 0 0 0 0 APPLICATION N.M. = not meaningful Due to the nature of the design of the transmitter in the DS2153Q, very little jitter (less than 0.005UIP-P broadband from 10Hz to 100kHz) is added to the jitter present on TCLK. Also, the waveforms that they create are independent of the duty cycle of TCLK. The transmitter in the DS2153Q couples to the E1 transmit shielded twisted pair or coax via a 1:1.15 or 1:1.36 step-up transformer as shown in Figure 13-1. For the devices to create the proper waveforms, the transformer used must meet the specifications listed in Table 13-3. Table 13-3. Transformer Specifications SPECIFICATION Turns Ratio Primary Inductance Leakage Inductance Intertwining Capacitance DC Resistance RECOMMENDED VALUE 1:1 (receive) and 1:1.15 or 1:1.36 (transmit) ±5% 600µH minimum 1.0µH maximum 60pF maximum 1.2Ω maximum 41 of 60 DS2153Q 13.3 Jitter Attenuator The DS2153Q contains an on-board jitter attenuator that can be set to a depth of either 32 or 128 bits via the JABDS bit in the Line Interface Control Register (LICR). The 128-bit mode is used in applications where large excursions of wander are expected. The 32-bit mode is used in delay sensitive applications. The characteristics of the attenuation are shown in Figure 13-4. The jitter attenuator can be placed in either the receive path or the transmit path by appropriately setting or clearing the JAS bit in the LICR. Also, the jitter attenuator can be disabled (in effect, removed) by setting the DJA bit in the LICR. In order for the jitter attenuator to operate properly, a crystal with the specifications listed in Table 13-4 must be connected to the XTAL1 and XTAL2 pins. The jitter attenuator divides the clock provided by the 8.192MHz crystal at the XTAL1 and XTAL2 pins to create an output clock that contains very little jitter. On-board circuitry will pull the crystal (by switching in or out load capacitance) to keep it long-term averaged to the same frequency as the incoming E1 signal. If the incoming jitter exceeds either 120UIP-P (buffer depth is 128 bits) or 28UIP-P (buffer depth is 32 bits), then the DS2153Q will divide the attached crystal by either 3.5 or 4.5 instead of the normal 4 to keep the buffer from overflowing. When the device divides by either 3.5 or 4.5, it also sets the Jitter Attenuator Limit Trip (JALT) bit in the Receive Information Register (RIR.5). Table 13-4. Crystal Selection Guidelines PARAMETER Parallel Resonant Frequency Mode Load Capacitance Tolerance Pullability Effective Series Resistance Crystal Cut SPECIFICATION 8.192MHz Fundamental 18pF to 20pF (18.5pF nominal) ±50ppm CL = 10pF, delta frequency = +175ppm to +250ppm CL = 45pF, delta frequency = -175ppm to -250ppm 30Ω maximum AT 42 of 60 DS2153Q Figure 13-1. External Analog Connections NOTE 1: ALL RESISTOR VALUES ARE ±1%. NOTE 2: THE RT RESISTORS ARE USED TO INCREASE THE TRANSMITTER RETURN LOSS OR TO PROTECT THE DEVICE FROM OVERVOLTAGE. NOTE 3: THE RR RESISTORS ARE USED TO TERMINATE THE RECEIVE E1 LINE. NOTE 4: FOR 75Ω TERMINATION, RR = 37.5Ω/FOR 12Ω TERMINATION RR = 60Ω. NOTE 5: SEE THE SEPARATE APPLICATION NOTE FOR DETAILS ON HOW TO CONSTRUCT A PROTECTED INTERFACE. 43 of 60 DS2153Q Figure 13-2. Jitter Tolerance Figure 13-3. Transmit Waveform Template 44 of 60 DS2153Q Figure 13-4. Jitter Attenuation 45 of 60 DS2153Q 14 TIMING DIAGRAMS Figure 14-1. Receive Side Timing NOTE 1: RSYNC IN THE FRAME MODE (RCR1.6 = 0). NOTE 2: RSYNC IN THE MULTIFRAME MODE (RCR1.6 = 1). NOTE 3: RLCLK IS PROGRAMMED TO OUTPUT JUST THE Sa4 BIT. NOTE 4: RLINK WILL ALWAYS OUTPUT ALL FIVE Sa BITS AS WELL AS THE REST OF THE RECEIVE DATA STREAM. NOTE 5: THIS DIAGRAM ASSUMES THE CAS MF BEGINS WITH THE FAS WORD. Figure 14-2. Receive Side Boundary Timing (with Elastic Stores Disabled) NOTE 1: RCHBLK IS PROGRAMMED TO BLOCK CHANNEL 2. NOTE 2: RLINK IS PROGRAMMED TO OUTPUT THE Sa4 BITS. NOTE 3: RLINK IS PROGRAMMED TO OUTPUT THE Sa4 AND Sa8 BITS. NOTE 4: RLINK IS PROGRAMMED TO OUTPUT THE Sa5 AND Sa7 BITS. NOTE 5: SHOWN IS A NON-ALIGN FRAME BOUNDARY. 46 of 60 DS2153Q Figure 14-3. 1.544MHz Boundary Timing with Elastic Store(s) Disabled NOTE 1: DATA FROM THE E1 CHANNELS 1, 5, 9, 13, 17, 21, 25, AND 29 IS DROPPED (CHANNEL 2 FROM THE E1 LINK IS MAPPED TO CHANNEL 1 OF THE T1 LINK, ETC.) AND THE F-BIT POSITION IS ADDED (FORCED TO 1). NOTE 2: RSYNC IS IN THE OUTPUT MODE (RCR1.5 = 0). NOTE 3: RSYNC IS IN THE INPUT MODE (RCR1.5 = 1). NOTE 4: RCHBLK IS PROGRAMMED TO BLOCK CHANNEL 24. Figure 14-4. 2.048MHz Boundary Timing with Elastic Store(s) Enabled NOTE 1: RSYNC IS IN THE OUTPUT MODE (RCR1.5 = 0). NOTE 2: RSYNC IS IN THE INPUT MODE (RCR1.5 = 1). NOTE 3: RCHBLK IS PROGRAMMED TO BLOCK CHANNEL 1. 47 of 60 DS2153Q Figure 14-5. Transmit Side Timing NOTE 1: TSYNC IN THE FRAME MODE (TCR1.1 = 0). NOTE 2: TSYNC IN THE MULTIFRAME MODE (TCR1.1 = 1). NOTE 3: TLINK IS PROGRAMMED TO SOURCE ONLY THE Sa4 BIT. NOTE 4: THIS DIAGRAM ASSEMBLES BOTH THE CAS MF AND THE CRC4 BEGIN WITH THE ALIGN FRAME. Figure 14-6. Transmit Side Boundary Timing NOTE 1: TSYNC IS IN THE INPUT MODE (TCR1.0 = 0). NOTE 2: TSYNC IS IN THE OUTPUT MODE (TCR1.0 = 1). NOTE 3: TCHBLK IS PROGRAMMED TO BLOCK CHANNEL 2. NOTE 4: TLINK IS PROGRAMMED TO SOURCE THE SA4 BITS. NOTE 5: TLINK IS PROGRAMMED TO SOURCE THE SA7 AND SA8 BITS. NOTE 6: SHOWN IS A NON-ALIGN FRAME BOUNDARY. NOTE 7: SEE Figure 14-3 AND Figure 14-4 FOR DETAILS ON TIMING WITH THE TRANSMIT SIDE ELASTIC STORE ENABLED. 48 of 60 DS2153Q Figure 14-7. G.802 Timing NOTE 1: RCHBLK OR TCHBLK IS PROGRAMMED TO PULSE HIGH DURING TIME SLOTS 1 TO 15, 17 TO 25, AND DURING BIT 1 OF TIME SLOT 26. 49 of 60 DS2153Q Figure 14-8. Synchronization Flowchart 50 of 60 DS2153Q Figure 14-9. Transmit Data Flow NOTE 1: TCLK MUST BE TIED TO RCLK (OR SYSCLK IF THE ELASTIC STORE IS ENABLED) AND TSYNC MUST BE TIED TO RSYNC FOR DATA TO BE PROPERLY SOURCED FROM RSER. 51 of 60 DS2153Q 15 DC CHARACTERISTICS ABSOLUTE MAXIMUM RATINGS Voltage Range on Any Pin Relative to Ground……………………………………………..-1.0V to +7.0V Operating Temperature Range Commercial……………………………………………………………...……………...0°C to 70°C Industrial…………………………………………………………………………….-40°C to +85°C Storage Temperature ………………………………………………………………………-55°C to +125°C Soldering Temperature...………………………………………..See IPC/JEDEC J-STD-020 Specification This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. Table 15-1. Recommended DC Characteristics (TA = 0°C to +70°C for DS2153Q, TA = -40°C to +85°C for DS2153QN.) PARAMETER SYMBOL MIN TYP MAX Logic 1 VIH 2.0 VDD + 0.3 Logic 0 VIL -0.3 +0.8 DS2153Q 4.75 5.25 Supply VDD DS2153QN 4.80 5.25 UNITS V V NOTES V 1 UNITS pF pF NOTES Table 15-2. Capacitance (TA = +25°C) PARAMETER Input Capacitance Output Capacitance SYMBOL CIN COUT MIN TYP 5 7 MAX Table 15-3. DC Characteristics (VDD = 5V ±5%, TA = 0°C to +70°C for DS2153Q; VDD = 5V +5%/-4%, TA = -40°C to +85°C for DS2153QN.) PARAMETER Supply Current at 5V Input Leakage Output Leakage Output Current (2.4V) Output Current (0.4V) SYMBOL IDD IIL ILO IOH IOL MIN TYP MAX 65 -1.0 -1.0 +4.0 NOTES: 1) Applies to RVDD, TVDD, and DVDD. 2) TCLK =2.048MHz. 3) 0V < VIN < VDD. 4) Applies to INT1 and INT1 when tri-stated. 52 of 60 +1.0 1.0 UNITS NOTES mA µA µA mA mA 2 3 4 DS2153Q 16 AC CHARACTERISTICS Table 16-1. AC Characteristics—Parallel Port (VDD = 5V ±5%, TA = 0°C to +70°C for DS2153Q; VDD = 5V +5%/-4%, TA = -40°C to +85°C for DS2153QN.) (See Figure 16-1, Figure 16-2, and Figure 16-3.) PARAMETER SYMBOL MIN TYP MAX UNITS NOTES Cycle Time tCYC 250 ns Pulse Width, DS Low or RD PWEL 150 ns High Pulse Width, DS High or RD PWEH 100 ns Low Input Rise/Fall Times tR, tF 30 ns tRWH 10 ns R/ W Hold Time R/ W Setup Time before DS tRWS 50 ns High CS Setup Time before DS, tCS 20 ns WR or RD Active tCH 0 ns CS Hold Time Read Data Hold Time tDHR 10 50 ns Write Data Hold Time tDHW 0 ns Muxed Address Valid to AS tASL 20 ns or ALE Fall Muxed Address Hold Time tAHL 10 ns Delay Time DS, WR or RD tASD 25 ns to AS or ALE Rise Pulse Width AS or ALE High PWASH 40 ns Delay Time, AS or ALE to tASED 20 ns DS, WR or RD Output Data Delay Time from 20 100 ns tDDR DS or RD Data Setup Time tDSW 80 ns 53 of 60 DS2153Q Figure 16-1. Intel Bus Read AC Timing Figure 16-2. Intel Bus Write AC Timing 54 of 60 DS2153Q Figure 16-3. Motorola Bus AC Timing 55 of 60 DS2153Q Table 16-2. AC Characteristics—Receive Side (VDD = 5V ±5%, TA = 0°C to +70°C for DS2153Q; VDD = 5V +5%/-4%, TA = -40°C to +85°C for DS2153QN.) (See Figure 16-4.) PARAMETER SYMBOL MIN TYP MAX UNITS NOTES ACLKI/RCLK Period tCP 488 ns tCH 180 244 ns 1 RCLK Pulse Width 180 244 ns tCL tCH 90 244 ns RCLK Pulse Width 2 tCL 200 244 ns tSP 648 ns 3 SYSCLK Period tSP 488 ns 4 tSH 50 ns SYSCLK Pulse Width tSL 50 RSYNC Setup to SYSCLK tSU 25 tSH -5 ns Falling RSYNC Pulse Width tPW 50 ns SYSCLK Rise/Fall Times tR, tF 25 ns Delay RCLK or SYSCLK to tDD 70 ns RSER Valid Delay RCLK or SYSCLK to tD1 50 ns RCHCLK Delay RCLK or SYSCLK to tD2 50 ns RCHBLK Delay RCLK or SYSCLK to tD3 50 ns RSYNC Delay RCLK to RLCLK tD4 50 ns Delay RCLK to RLINK Valid tD5 50 ns NOTES: 1) Jitter attenuator enabled in the receive side path. 2) Jitter attenuator disabled or enabled in the transmit path. 3) SYSCLK = 1.544MHz. 4) SYSCLK = 2.048MHz. 56 of 60 DS2153Q Figure 16-4. Receive Side AC Timing NOTE 1: RSYNC IS IN THE OUTPUT MODE (RCR1.5 = 0). NOTE 2: RSYNC IS IN THE INPUT MODE (RCR1.5 = 1). NOTE 3: RLCLK AND RLINK ONLY HAVE A TIMING RELATIONSHIP TO RCLK. NO TIMING RELATIONSHIP BETWEEN RLCLK/RLINK AND RSYNC IS IMPLIED. NOTE 4: RCLK CAN EXHIBIT A SHORT HIGH TIME IF THE JITTER ATTENUATOR IS EITHER DISABLED OR IN THE TRANSMIT PATH. 57 of 60 DS2153Q Table 16-3. AC Characteristics—Transmit Side (VDD = 5V ±5%, TA = 0°C to +70°C for DS2153Q; VDD = 5V +5%/-4%, TA = -40°C to +85°C for DS2153QN.) (See Figure 16-5.) PARAMETER SYMBOL MIN TYP MAX UNITS NOTES TCLK Period tP 488 ns tCH 75 ns TCLK Pulse Width 75 ns tCL TSER and TLINK Set up to tSU 25 ns 1 TCLK Falling TSER and TLINK Hold from tHD 25 ns 1 TCLK Falling TSYNC Set up to TCLK 25 tCH -5 tSU Falling TSYNC Pulse Width tPW TCLK Rise/Fall Times tR, tF 25 ns Delay TCLK to TCHCLK tD1 50 ns Delay TCLK to TCHBLK tD2 50 ns Delay TCLK to TSYNC tD3 50 ns Delay TCLK to TLCLK tD4 50 ns NOTES: 1) If the transmit side elastic store is enabled, then TSER is sampled on the falling edge of SYSCLK and the parameters tSU and tHD still apply. 58 of 60 DS2153Q Figure 16-5. Transmit Side AC Timing NOTE 1: TSYNC IS IN THE OUTPUT MODE (TCR1.0 = 1). NOTE 2: TSYNC IS IN THE INPUT MODE (TCR1.0 = 0). NOTE 3: NO TIMING RELATIONSHIP BETWEEN TSYNC AND TLCLK/TLINK IS IMPLIED. NOTE 4: TSER IS SAMPLED ON THE FALLING EDGE OF SYSCLK IF THE TRANSMIT SIDE ELASTIC STORE IS ENABLED 59 of 60 DS2153Q 17 PACKAGE INFORMATION (The package drawing(s) in this data sheet may not reflect the most current specifications. The package number provided for each package is a link to the latest package outline information.) 17.1 44-Pin PLCC (56-G4003-001) 60 of 60 Maxim/Dallas Semiconductor cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim/Dallas Semiconductor product. No circuit patent licenses are implied. Maxim/Dallas Semiconductor reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2006 Maxim Integrated Products • Printed USA The Maxim logo is a registered trademark of Maxim Integrated Products, Inc. The Dallas logo is a registered trademark of Dallas Semiconductor.