DS34S132DK

DS34S132 Evaluation Kit Evaluates: DS34S132 General Description The DS34S132 evaluation kit (EV kit) is an easy-to-use EV kit for evaluating the DS34S132 32-port TDM-overpacket (TDMoP) IC. The EV kit is a stand-alone system with a TDMoP chip, local oscillator, local control processor, memory, external E1/T1 LIUs and framers, power supply, and user interface software included in a 2.5 RU enclosure. The EV kit is controlled over an RS-232 serial link from an external ASCII terminal (typically using terminal emulation software running on a PC) or through a telnet session. The ASCII user interface is menu driven and hierarchical for easy use. The behavior and performance of the TDMoP IC can be evaluated with a single EV kit where the Ethernet signal is looped back to the kit, or with two EV kits configured as separate end points. EV Kit Contents DS34S132 EV Kit System TDMoP IC Daughter Card (Factory Installed) MPC8313 CPU Daughter Card (Factory Installed) User Interface Software (Factory Installed) Ordering Information PART DS34S132DK TYPE EV Kit Features S Complete System: Motherboard and Daughter Cards in a Convenient 2.5 RU Enclosure S Menu-Driven ASCII Text User Interface Software S System Processor on a Separate Daughter Card S Ethernet PHYs, I/O Jacks, E1/T1 Transceivers, and Clock Sources on Motherboard S Built-In AC Power-Supply Module S Several Popular TCXO and OCXO Oscillators from Which to Select and BNC Connectors for Lab References S 9-Pin Serial Jack to Connect an ASCII Terminal for Configuration and Status S System TCP/IP Stack for Configuration and Status Over IP/Ethernet S One RJ45 Ethernet Jack for Connection to the Ethernet Network S One RJ45 Jack for Each E1/T1 Port S RJ45 External Clock Input Jack S BNC Common Clock Input Jack S BNC Reference Clock Input Jack S 16-Bit CPU Interface to TDMoP IC TDMoIP® Evaluation System with No Lid TDMoIP is a registered trademark of RAD Data Communications, Ltd. For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim’s website at www.maximintegrated.com. 19-5865; Rev 0; 5/11 DS34S132 Evaluation Kit Evaluates: DS34S132 TABLE OF CONTENTS 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1.3 Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1.3.1 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1.4 Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1.4.1 Recommended Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1.4.2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1.5 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1.5.1 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1.5.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.5.3 Timing Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.5.4 Ethernet Clock Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 1.5.5 Motherboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 1.5.6 CPU Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 1.5.7 TDMoP IC Daughter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 1.5.8 Bundles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 1.5.9 Packet Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 1.5.10 TDMoP Mappings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 1.5.11 Payload Type Machines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 1.5.12 OAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 1.5.13 Packet Delay Variation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 1.5.13.1 Differential Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 1.5.13.2 End-to-End Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 1.5.14 End-to-End Alarm Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 1.5.15 Default Gateway Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.2 Making Internal Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.2.1 Opening the DS34S132 EV Kit Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.2.2 Setting the Internal Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.3 Connecting to the Ethernet Network Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 2.4 Connecting to the TDM Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 2.5 Connecting to the Clock Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 2.5.1 Connecting to the External Clock Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 2.5.2 Connecting to the Common Clock Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 2.5.3 Connecting to the Reference Clock Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 2.5.4 Connecting to an ASCII Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 2   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 TABLE OF CONTENTS (continued) 3. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 3.1 Front Panel Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3.2 User Interface Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3.2.1 Using the Control Port and an ASCII Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3.2.2 Using Telnet Through the Ethernet Management Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 3.2.3 Choosing Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 3.2.4 Redisplaying the Current Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 3.2.5 Saving Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4. Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4.1 Preliminary Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4.2 Configuring General Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 4.3 Configuring TDM Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 4.3.1 Configuring E1 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 4.3.2 Configuring T1 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 4.4 Configuring Bundles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 4.4.1 Configuring SAToP Bundles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 4.4.2 Configuring CESoPSN Bundles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 4.5 Deleting Bundles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 4.6 Displaying Active Bundles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 4.7 Restoring Default Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 5. Troubleshooting and Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 5.1 Displaying Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 5.1.1 Displaying General Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 5.1.2 Displaying Interface Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 5.1.3 Displaying Bundle Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 5.1.3.1 SAToP/CES Bundle Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 5.2 Displaying Performance Monitoring Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 5.2.1 Displaying Ethernet Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 5.2.2 Displaying Bundle Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 5.2.2.1 Displaying SAToP/CES Bundle Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 5.2.3 Displaying TDM Interface Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 5.3 Utility Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 5.3.1 Read Memory/Write Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 5.3.2 Update ToP Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 5.3.3 Set Debug Flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 5.4.4 Management Network Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 5.3.5 Loopbacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Maxim Integrated   3 DS34S132 Evaluation Kit Evaluates: DS34S132 TABLE OF CONTENTS (continued) 5.3.5.1 Enabling Loopbacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 5.3.5.2 Framer Loopback and Payload Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 5.3.5.3 Local Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 5.3.5.4 Remote Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 5.3.5.5 Ethernet Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 5.3.5.6 PHY Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 5.3.6 Reboot System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 5.3.7 UART Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 5.3.8 Read Script Configuration File from Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 5.3.9 Send OAM Packet to Other Party . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 5.3.10 Read S132 Memory/Write S132 Memory (DDR Memory) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 5.3.11 Read DSP Memory/Write DSP Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 5.3.12 System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 5.3.13 Execute Linux Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 5.4 Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Appendix A. Connector Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 A.1 E1/T1 and External Clock Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 A.2 Ethernet Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 A.3 ASCII Terminal Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 LIST OF FIGURES Figure 1-1. TDMoIP Evaluation System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Figure 1-2. Quick Start Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 1-3. DS34S132 EV Kit Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Figure 1-4. Representation of DS34S132 EV Kit Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 1-5. E1/T1 Per Port Clock Distribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 1-6. CPU and Peripherals Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Figure 1-7. TDMoIP Packet with VLAN Tag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Figure 1-8. TDMoMPLS Packet with VLAN Tag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Figure 1-9. TDMoMEF Packet with VLAN Tag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Figure 1-10. TDMoIP Encapsulation in an Ethernet Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Figure 1-11. Packet Delay Variation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Figure 1-12. Jitter Buffer Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 2-1. Motherboard Jumper Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 4   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 LIST OF FIGURES (continued) Figure 2-2. CPU Daughter Card Jumper Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Figure 2-3. UPLINK Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Figure 2-4. T1/E1 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Figure 2-5. EXT CLK Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Figure 2-6. COMM CLK Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Figure 2-7. REF CLK Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 2-8. CONSOLE Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 3-1. DS34S132 EV Kit Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Figure 3-2. Main Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Figure 4-1. Preliminary Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Figure 4-2. General Configuration (Main Menu→General Configuration) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Figure 4-3. OAM Configuration (Main Menu→General Configuration→OAM Configuration) . . . . . . . . . . . . . . . . . . . . 29 Figure 4-4. TDM Interface Selection (Main Menu→Interface Configuration) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Figure 4-5. E1 Interface Configuration (Main Menu→Interface Configuration→E1 Interface Configuration) . . . . . . . . 30 Figure 4-6. T1 Interface Configuration (Main Menu→Interface Configuration→T1 Interface Configuration) . . . . . . . . . 32 Figure 4-7. SAToP Bundle Configuration (Main Menu→Bundle Configuration→SAToP Bundle Configuration) . . . . . . 36 Figure 4-8. CESoPSN Bundle Configuration (Main Menu→Bundle Configuration→CES Bundle Configuration) . . . . . 42 Figure 5-1. TopAlarms Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Figure 5-2. General Alarms Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Figure 5-3. TDM Alarms Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Figure 5-4. Adaptive Alarms Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Figure 5-5. SAToP/CES Bundle Alarms Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Figure 5-6. Performance Monitoring Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Figure 5-7. Ethernet Performance Data Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Figure 5-8. SAToP/CES Bundle Counter Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Figure 5-9. Loopbacks Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Figure 5-10. Local Loopback Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Figure 5-11. Remote Loopback Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Figure 5-12. Ethernet Loopback Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Figure 5-13. PHY Loopback Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Maxim Integrated   5 DS34S132 Evaluation Kit Evaluates: DS34S132 LIST OF TABLES Table 1-1. Maximum PDVT for E1/T1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Table 1-2. Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Table 2-1. Motherboard Jumper and Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Table 2-2. CPU Daughter Card Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Table 3-1. DS34S132 EV Kit LEDs and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Table 4-1. Preliminary Configuration Parameter Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Table 4-2. General Configuration Parameter Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Table 4-3. OAM Configuration Parameter Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Table 4-4. E1 Interface Configuration Parameter Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Table 4-5. T1 Interface Configuration Parameter Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Table 4-6. SAToP Bundle Parameter Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Table 4-7. CESoPSN Bundle Parameter Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Table 5-1. General Alarms Parameter Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Table 5-2. TDM Alarms Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Table 5-3. Adaptive Alarms Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Table 5-4. SAToP or CES Bundle Alarm Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Table 5-5. Ethernet Performance Data Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Table 5-6. SAToP/CES Bundle Counter Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Table 5-7. DS32S132 EV Kit Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Table 5-8. Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Table A-1. E1/T1 and External Clock Interface Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Table A-2. Ethernet Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Table A-3. Control Interface Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 6   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 1. Introduction 1.2 Features 1.1 Overview Three operating modes for E1/T1 are supported: unframed, framed, and framed-with-CAS. Bundles consisting of carrying entire TDM data streams or selected TDM time slots are transported over the network based on IP/MPLS/MEF addressing. The DS34S132 evaluation kit (EV kit) is a complete evaluation platform. The system consists of the following: • Four octal E1/T1 transceivers (a transceiver is a framer plus an LIU) • TDMoP IC daughter card • Motorola MPC8313 CPU daughter card • Clock subsystem based on the DS3100 clock sync chip • Uplink port for the 100/1000Mbps Ethernet (supports autonegotiation) • 10/100/1000Mbps Ethernet management port connected to the MPC8313 Ethernet controller for debugging • Peripheral memory and glue logic VLAN tagging and priority labeling are supported, according to 802.1p and Q. The type of service (ToS) of outgoing IP packets is user-configurable. Synchronization between TDM interfaces is maintained by deploying advanced clock distribution mechanisms. The clocking options include internal, loopback, recovered clock (either adaptive or common clock), or an externally provided E1/T1 station clock. The TDMoP IC is connected to 32 E1/T1 transceivers (four DS26518s) on the motherboard to complete the TDM-to-packet path. • RS-232 interface for control and configuration using an ASCII terminal Figure 1-1. TDMoIP Evaluation System Maxim Integrated   7 DS34S132 Evaluation Kit Evaluates: DS34S132 1.4.2 Procedure Tx T1/E1–Rx DS34S132 EV KIT (MASTER) SERIAL CABLE OR ETHERNET BERT Rx T1/E1–Tx ETHERNET PC DS34S132 EV KIT (SLAVE) SERIAL CABLE OR ETHERNET Figure 1-2. Quick Start Connections Note: In the following sections, software-related items are identified by bolding. Text in bold refers to items within the terminal emulator menu system. Text that is bold and underlined indicates user input. 1) Connect cables as shown in Figure 1-2. 2) Connect the EV kit to a PC equipped with ASCII terminal emulation software (e.g., Windows HyperTerminal or PuTTY). 3) Configure the BERT to send a pseudorandom pattern over E1 framed. 4) Power-up both DS34S132 EV kits. 1.3 Physical Description 1.3.1 Front Panel The front panel contains the following: • Ethernet uplink port with indicator LEDs for ETH LINK and ETH ACT • TDM ports—32 E1/T1 ports with indicator LEDs for LOS and LOF • Control port (CONSOLE) (RS-232 for connection of an ASCII terminal) • T1/E1 external station clock (BITS) • Ethernet management port with indicator LEDs for ETH LINK and ETH ACT • Common clock reference port (used for differential clock recovery) • Reference clock port (optional use for TDM clock recovery) 5) Follow the initialization sequence as noted in 3.2 User Interface Software (this is copied below for convenience). a. Set the port parameters of the control terminal PC to 115.2kbps, 8 bits/character, 1 stop bit, no parity. If available, set the terminal emulator to ANSI VT100 emulation (for optimal view of system menus). b. At the end of the initialization and self-test, system software detects the part number of the TDMoP IC on the internal daughter card and displays it on the terminal screen as: login: The login ID is target and the password is password. After giving the password, the screen appears as: ~ $ See 2. Installation for additional information. Write the following commands in sequence as shown: 1.4 Quick Start ~ $ su 1.4.1 Recommended Equipment • Two Maxim DS34S132 EV kit evaluation boards • Two serial cables or Ethernet connection from PC to both DS34S132 EV kits • PC to run terminal emulation (e.g., WindowsM HyperTerminal or PuTTY) • Ethernet cable for connection between the DS34S132 EV kits • T1/E1 cable(s) • Test set (ANT20 or other BERT for E1) ~ $ password: root ~ $ ./ins132 ~ $ ./top32App The Main Configuration (S132) menu is displayed in the terminal. 6) Master DS34S132 EV kit configuration (at the Main Configuration (S132) menu) (this configures the device for E1 operation, which is the default): a. Select 2. General Configuration. b. Select 3. Source IP 1. Windows is a registered trademark of Microsoft Corp. 8   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 c. Set to 10.10.10.4. m. Select 1. Bundle Type, set to SAToP. d. Type s to save. n. Select 2. Assign this Bundle to PCM port, set to 1. e. Press ESC to return to Main Configuration (S132) menu. o. Select 6. TX Bundle Number, set to 1. f. Select 3. Interface Configuration. g. Select 1. Frame Type, set to Unframed. q. Select 10. Destination IP Address, set to 10.10.10.4. h. Select 7. Clock Source, set to Loopback. r. Select 22. Clock Recovery, set to Yes. i. Select 11. IF Type, set to Unbalanced. s. Select 36. Size in Bytes, set to 1280 (E1 payload size). j. Type s to save. k. Press ESC to return to the Main Configuration (S132) menu. l. Select 4. Bundle Configuration. m. Select 1. Bundle Type, set to SAToP. n. Select 2. Assign this Bundle to PCM port, set to 1. o. Select 6. TX Bundle Number, set to 1. p. Select 7. RX Bundle Number, set to 1. q. Select 10. Destination IP Address, set to 10.10.10.5. r. Select 22. Clock Recovery, set to No. s. Select 36. Size in Bytes, set to 1280 (E1 payload size) . t. Type s to save. u. Press ESC to return to the Main Configuration (S132) menu. 7) Slave DS34S132 EV kit configuration (at the Main Configuration (S132) menu): a. Select 2. General Configuration. b. Select 3. Source IP 1. c. Set to 10.10.10.5. d. Type s to save. e. Press ESC to return to the Main Configuration (S132) menu. f. Select 3. Interface Configuration. g. Select 1. Frame Type, set to Unframed. h. Select 7. Clock Source, set to Recovery. i. Select 11. IF Type, set to Unbalanced. j. Type s to save. k. Press ESC to return to the Main Configuration (S132) menu. l. Select 4. Bundle Configuration. Maxim Integrated p. Select 7. RX Bundle Number, set to 1. t. Type s to save. u. Press ESC to return to the Main Configuration (S132) menu. 8) This completes the configuration of both boxes, and packets should be flowing in both direction over the Ethernet link. Verify setup is operational without errors. 1) Check the BERT for errors. 2) Check the DS34S132 EV kit performance monitors (on either the master or the slave). a. From the Main Configuration (S132) menu, select 8. Performance (PM). b. Select 1. Ethernet Performance. c. Line 1. displays Correct Bytes (RX) and Correct Bytes (TX). These two numbers should match. d. Press ESC to return to the Performance (PM) menu. e. Select 3. Bundle Performance. f. It prompts Please enter the Bundle ID:, enter 1. g. Lines 1. and 2. report Correct Frames Tx to LAN and Correct Frames Rx from LAN. These two values should match. 1.5 Functional Description 1.5.1 Interfaces E1. The E1 interface complies with the following standards: ITU-T Rec. G.703, G.704, G.706, G.732, and G.823. The E1 framers support unframed (pass-through), framed, and framed-with-CAS. Long-haul/short-haul options can be selected by configuration. T1. The T1 interface complies with the following standards: AT&T TR-62411, ITU-T Rec. G.703, G.704, ANSI T1.403, and G.824. The T1 framers support unframed (pass-through), SF, and ESF.   9 DS34S132 Evaluation Kit Evaluates: DS34S132 Ethernet Uplink. The Ethernet uplink interface complies with the following standards: IEEE 802.3, 802.3u, and 802.1p and Q. This interface is a standard 100/1000BASE-T full-duplex Ethernet port with autonegotiation support. The EV kit supports VLAN tagging and priority. A different VLAN can be configured for each bundle. The data stream coming from the E1/T1 interfaces is encapsulated into IP/MPLS/MEF packets and transferred over the Ethernet port, and vice versa. When using IP, a destination IP address should be configured for each bundle. When using MPLS, a bundle should be configured with an MPLS label. Ethernet Management. The local Ethernet management interface enables the connection of a software debugger to the DS34S132 EV kit CPU. The interface is a standard RJ45 + MAGNETIC 10/100/1000 ETHERNET 10/100/1000BASE-T Ethernet port with autonegotiation support that complies with the IEEE 802.3 standard. E1/T1 External Clock. The E1/T1 external clock port enables connection of an external clock source to support the station clock mode. Common Clock. The common clock port enables connection of a common clock source through LVTTL input. It supports frequencies of up to 25MHz. The common clock is used for differential mode clock recovery. Reference Clock. The reference clock port allows for an external source to be used for TDM clock recovery from the Ethernet link. RS-232 Control. The RS-232 control interface enables connection an ASCII terminal for configuring the EV kit. ETHERNET UPLINK MCLK DDRCLK AND ETHCLK OSC LIUCLK RJ45/1, 2 E1/T1 OCTAL TRANSCEIVER DS26518 #1 RJ45/3, 4 RJ45/5, 6 VOLTAGE SUPPLY 3V, 2.5V, 1.8V RJ45/7, 8 TDM CLOCK/DATA RJ45/9, 10 E1/T1 OCTAL TRANSCEIVER DS26518 #2 RJ45/11, 12 RJ45/13, 14 DDR SDRAM TDM CLOCK/DATA RJ45/15, 16 CONNECTORS FOR DEBUG DS34S132 TDM CLOCK/DATA RJ45/17, 18 E1/T1 OCTAL TRANSCEIVER DS26518 #3 RJ45/19, 20 RJ45/21, 22 TDM CLOCK/DATA DAUGHTER CARD RJ45/23, 24 PORT 31, 32 CPLD HEADER RJ45/25, 26 E1/T1 OCTAL TRANSCEIVER DS26518 #4 RJ45/27, 28 RJ45/29, 30 RJ45/31, 32 A/D BUS SYSCLK COMMON CLOCK REFCLK FPGA TCXO DS3100 CLOCK SYNC RJ45/E1/T1 CLK STATION CLOCK E1/T1 CMNCLK CLOCK CPLD REFCLK EXTCLK[0,1] POWER QUICC II PRO MPC8313 DAUGHTER CARD TCXO RJ45/ETH MNG DDR2 SDRAM OCXO ETHERNET PHY 10/100/1000 MPC8313 SMC OSC DB9 THERMINAL CONNECTOR RS-232 DRIVER Figure 1-3. DS34S132 EV Kit Block Diagram 10   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 E1/T1 E1/T1 E1/T1 E1/T1 E1/T1 - 1 E1/T1 - 2 E1/T1 - 3 E1/T1 - 4 ETH-UPLINK E1/T1 ETHERNET E1/T1 - 32 EXT-CLK COMM-CLK E1/T1 EXTERNAL CLOCK COMMON CLOCK REF-CLK REFERENCE CLOCK CONTROL ETH-MNG RS-232 CONTROL ETHERNET MANAGEMENT Figure 1-4. Representation of DS34S132 EV Kit Interfaces Ethernet packets without regard for frame alignment. This option provides clear channel end-to-end service. E1/T1 FRAMER TSER TDAT RSER RDAT TSIG TSIG RSIG RSIG In framed and framed-with-CAS modes, the incoming bit stream is regarded as a sequence of n x 64kbps channel groups. This mode allows fractional or full E1/ T1 transmission. DS34S132 RSYSCLK TCLK TCLKO TSYNC TSYNC RSYNC RFSYNC RCLK RSYNC RCLK Figure 1-5. E1/T1 Per Port Clock Distribution 1.5.2 Modes of Operation The EV kit modes of operation for E1/T1 are the following: • Unframed • Framed • Framed-with-CAS In unframed mode, the entire incoming bit stream from each interface is encapsulated into IP/MPLS/MEF-over- Maxim Integrated 1.5.3 Timing Modes The E1/T1 transmit (Tx) clock operates in several timing modes to provide maximum flexibility for the EV kit TDM interface. The available timing modes are the following: • Loopback Timing: The clock is derived from the received TDM clock. • Recovered Clock Timing: The clock is regenerated from the ETH network using the clock recovery mechanism. • Internal Clock Timing: The clock is provided by an internal oscillator. • E1/T1 Station Clock Timing: The clock is provided by the external E1/T1 clock source. These selections are accessed through the user interface software. See 4.3 Configuring TDM Interfaces for more information. Figure 1-5 shows the TDM backplane wiring for one E1/T1 port of the system (there are 32 total E1/T1 TDM ports).   11 DS34S132 Evaluation Kit Evaluates: DS34S132 1.5.4 Ethernet Clock Recovery 1.5.6 CPU Board The DS34S132 uses either CMNCLK or REFCLK pins as its reference clock input to recover the TDM timing from the Ethernet source using either “Adaptive Clock Recovery” or “Differential Clock Recovery.” These clock inputs are sourced from the on-board CPLD and are user-selectable from TCXOs, an OCXO, an E1/T1 station clock, or an external reference on one of the BNC jacks (CMNCLK or REFCLK BNC jacks). Figure 1-6 shows the CPU and peripherals block diagram. The CPU clock is obtained from an on-board local crystal oscillator. 1.5.5 Motherboard The motherboard consists of four octal T1/E1 transceivers, a timing synthesizer (DS3100 clock sync), various TCXOs, an OCXO, two CPLDs, and an FPGA. The DS3100 clock sync provides clock sources to the CPLD, which acts as a mux to allow software selection of the various clock sources to the DS34S132. The FPGA provides CPU timing signals to the devices on the address/data bus. One CPLD provides userselectable clock sources and the other CPLD breaks out ports 31 and 32 of the TDM backplane for connection to an alternative LIU (e.g., the T3/E3 LIU, DS3150). The flash device has a 64Mb memory capacity. The flash is used for storage of software and configuration data that should not be lost when system power is off. The RAM memory consists of a DDR2 SDRAM device with a capacity of 512Mb. The CPU provides 16-bit data bus synchronous with the address bus. The CPU can accept and prioritize multiple external interrupts. One interrupt is connected to the TDMoP IC daughter card. MPC8313’s SMC communication port, used as a UART, is connected through an RS-232 transceiver to the DB9 control port on the front panel of the system. An ASCII terminal connected to the control port can be used to configure the system. The MPC8313’s Ethernet communication controller is connected through an Ethernet PHY to the Ethernet management port (MNG) on the front panel of the system. ETH PHY ETH PHY ETH CONTROLLER MPC8313 DDR2 TXD RXD SMC A/D BUS SERIAL Tx/Rx FLASH INCLUDING BOOT Figure 1-6. CPU and Peripherals Block Diagram 12   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 1.5.7 TDMoP IC Daughter Card The TDMoP IC daughter card is populated with a Maxim TDMoP IC (DS34S132) and a 512Mb DDR SDRAM. The core voltage is 1.8V for the TDMoP IC. I/Os are supplied with 3.3V. In addition, 2.5V is made from the 3.3V power supply through an on-board linear regulator. 1.5.8 Bundles A bundle is defined as a stream of bits originating from one TDM interface that are transmitted from a TDMoP source device to a TDMoP destination device. For example, a bundle can comprise any number of 64kbps time slots originating from a single E1 or T1 interface. Bundles are single-direction streams, frequently coupled with bundles in the opposite direction to enable fullduplex communications. More than one bundle can be transmitted between two TDMoP edge devices. Each bundle transmitted or received by the EV kit uses one of the following payload type methods: • TDMoIP using CESoPSN or SAToP payload type method • TDMoMPLS using CESoPSN or SAToP payload type method • TDMoMEF using CESoPSN or SAToP payload type method • HDLCoIP • HDLCoMPLS Up to 256 bundles are supported. Each TDMoP bundle/ connection can be assigned to one of the payload type machines or to the CPU. 1.5.9 Packet Formats DA MAC_addr/ BROADCAST/ MULTICAST SA VLAN TAG UP TO 2 TAGS ETH TYPE IP IP HEADER DEST. IP = IP_Add1/ IP_Add2 UDP* OR L2TPv3 HEADER Bundle no. = Bundle_Identifier/ OAM_bundle_num CONTROL WORD PAYLOAD TYPE HDLC/OAM/SAToP/ CESoPSN CRC32 *THE UDP SOURCE PORT NUMBER IS USED AS THE BUNDLE NUMBER DESIGNATOR, WHILE UDP DESTINATION PORT NUMBER IS SET TO 0x085E (2142), THE USER PORT NUMBER ASSIGNED BY IANA TO TDMoIP. Figure 1-7. TDMoIP Packet with VLAN Tag DA MAC_addr/ BROADCAST/ MULTICAST SA VLAN TAG UP TO 2 TAGS ETH TYPE MPLS UP TO 2 MPLS LABELS OPTIONAL MPLS LABEL* Bundle no. = Bundle_Identifier/ OAM_bundle_num CONTROL WORD PAYLOAD TYPE HDLC/OAM/SAToP/ CESoPSN CRC32 PAYLOAD TYPE HDLC/OAM/SAToP/ CESoPSN CRC32 *A STACK OF UP TO THREE MPLS LABELS IS SUPPORTED, WHERE THE INNER LABEL IS USED AS THE BUNDLE NUMBER DESIGNATOR. Figure 1-8. TDMoMPLS Packet with VLAN Tag DA MAC_addr/ BROADCAST/ MULTICAST SA VLAN TAG UP TO 2 TAGS ETH TYPE MEF ECID = Bundle_Identifier CONTROL WORD Figure 1-9. TDMoMEF Packet with VLAN Tag Maxim Integrated   13 DS34S132 Evaluation Kit Evaluates: DS34S132 1.5.10 TDMoP Mappings To transport TDM data through packet switched networks, the EV kit encapsulates it into Ethernet packets, as shown in Figure 1-10. The UDP/IP, L2TPv3/IP, MEF, and MPLS headers, as well as the TDMoIP control word, are detailed in the packets formats section of Maxim's TDMoP IC data sheets. 1.5.11 Payload Type Machines SAToP. The SAToP payload type machine converts unframed E1/T1 or serial data flows into IP, MPLS, or Ethernet packets and vice versa according to ITU-T Y.1413, MEF 8, MFA 8.0.0, and IETF RFC 4553. CESoPSN. The CESoPSN payload type machine converts structured E1/T1 data flows into IP, MPLS, or Ethernet packets and vice versa with static assignment of time slots inside a bundle according to ITU-T Y.1413, MEF 8, MFA 8.0.0, and IETF RFC 5086. HDLC. The HDLC payload type machine, for efficient transfer or termination of frame-based traffic, provides an HDLC controller for each bundle assigned to it. It supports 2, 7, and 8-bit time-slot resolution (i.e., 16, 56, and 64kbps, respectively), as well as N x 64kbps bundles (N = 1 to 32). This is useful in applications where HDLCbased signaling interpretation is required (such as ISDN D-channel signaling termination, V.51/2, or GR-303), or for trunking packet-based applications (such as frame relay), according to IETF RFC 4618. 1.5.12 OAM OAM is used to detect a valid connection. It can be set to enable or disable. When a bundle in the EV kit is OPTIONAL OPTIONAL PREAMBLE START OF FRAME DELIMITER DESTINATION ADDRESS SOURCE ADDRESS VLAN TAG1 VLAN TAG2 TYPE DATA AND PADDING FRAME CHECK SEQUENCE 7 BYTES 1 BYTE 6 BYTES 6 BYTES 4 BYTES 4 BYTES 2 BYTES 46–1500 BYTES 4 BYTES UDP/IPv4 HEADER OPTIONAL 26 BYTES OR RTP HEADER TDMoIP CONTROL WORD UDP/IPv6 HEADER 12 BYTES 4 BYTES TDMoIP PAYLOAD 48 BYTES OR L2TPv3/IPv4 HEADER 24, 28, OR 32 BYTES OR L2TPv3/IPv6 HEADER OPTIONAL 44, 48, OR 52 BYTES OR TDMoIP CONTROL WORD RTP HEADER MEF HEADER 4 BYTES 12 BYTES TDMoIP PAYLOAD 4 BYTES OR MPLS HEADER 4, 8, OR 12 BYTES Figure 1-10. TDMoIP Encapsulation in an Ethernet Frame 14   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 assigned with OAM, TDMoIP traffic is not sent immediately. First, a TDMoIP echo request packet is sent once every five seconds. This continues until a valid echo reply arrives. The remote TDMoP system receives the echo request packet and sends a valid echo reply only if all parameters in the echo request match its local configuration. When a valid echo reply arrives, the transmitting echo request message stops, and TDMoP traffic flow begins at full rate for that bundle. If there is a break in the connection, the initialization process begins again. Refer to the VCCV OAM and UDP/IP-specific OAM sections of the DS34S132 IC data sheet for details of the OAM payload types. 1.5.13 Packet Delay Variation Packets are transmitted at set intervals. Packet delay variation (PDV) is the maximum deviation from the nominal time the packets are expected to arrive at the receiving device. The TDMoP IC controls a buffer that compensates for the deviation from the expected packet arrival time to prevent buffer overflow or underflow. Packet delay variation is an important network parameter. Large PDV (exceeding the jitter buffer configuration) causes receive buffer overflow or underflow and errors in the recovered E1/T1 signal. To compensate for large PDV, the packet delay variation tolerance (PDVT) (jitter) buffer should be configured to a higher value. The jitter buffer depth is defined by the Rx_max_buff_size parameter. When the jitter buffer level reaches the value of Rx_max_buff_size, an overrun situation is declared. The differential time parameter defines the amount of data to be stored in the jitter buffer to compensate for network delay variation. This parameter has two implications: • Differential time defines the IC’s immunity to network packet delay variation. • The data arriving from the network is delayed by differential time before it is sent to the TDM interface. Differential time should be smaller than Rx_max_buff_ size. Also, the difference between Rx_max_buff_size and differential time should be larger than the time required to reconstruct a packet (otherwise an overrun can occur). Configuring the jitter buffer parameters correctly avoids underrun and overrun situations. Underrun occurs when the jitter buffer becomes empty (data is being written to the buffer more slowly than data is being read out of the buffer). Overrun occurs when the jitter buffer is full and there is no room for new data (data is being read out of the buffer more slowly than data is being written to the buffer). See Figure 1-12. Table 1-1 shows the maximum configurable value for differential time. Table 1-1. Maximum PDVT for E1/T1 1.5.13.1 Differential Time The TDMoP IC is equipped with a PDVT buffer. The PDVT buffer is filled by the payload of incoming packets and emptied to fill the outgoing E1/T1 or serial data stream. E1 (ms) T1 (ms) Unframed TDM FRAME TYPE 256 340 Framed-without-CAS 256 256 Framed-with-CAS 256 192 PACKETS LEAVING THE NEAR-END OF THE EVALUATION BOARD t PACKETS ARRIVING AT THE FAR-END OF THE EVALUATION BOARD t PDV Figure 1-11. Packet Delay Variation Maxim Integrated   15 DS34S132 Evaluation Kit Evaluates: DS34S132 1.5.15 Default Gateway Configuration Rx_max_buff_size THIS AREA IS EMPTY AND CAN BE USED TO STORE INCOMING BURSTS. The EV kit supports a default gateway configuration. In addition, a different Next Hop can be configured for each bundle. Table 1-2. Technical Specifications Standards ITU-T Rec. G.703, G.704, G.706, G.732, G.823 Framing Unframed, structured Data Rate 2.048Mbps Line Code HDB3 Receive Level 0 to -28dB with LTU, 0 to -9dB without LTU Transmit Level Q3V Q10%, balanced Line Impedance 120I Jitter Performance Per ITU-T G.823 End-to-End Delay = PDVT + Packet Creation Time + Fixed Network Delay Connector 8-pin RJ45 where PDVT is measured in seconds, Packet Creation Time is measured in seconds, and time of one time slot = 1/8kHz. Standards AT&T TR-62411, ITU-T Rec. G.703, G.704, ANSI T1.403, G.824 Data Rate 1.544Mbps SAToP (Unstructured) Packets: Line Code B8ZS, B7ZS Framing Unframed, SF, ESF DIFFERENTIAL TIME THIS AREA IS FULL AND THERE IS STILL DATA TO SEND ON THE LINE IF INCOMING DATA IS MISSING DUE TO NETWORK DELAYS. Figure 1-12. Jitter Buffer Parameters E1 1.5.13.2 End-to-End Delay The data path end-to-end delay, which is a function of all connections and network parameters, is calculated as follows:   1 = Packet Creation Time   × SB × (NTS 64K) 8bit   where SB = size of packet in bytes. Receive Level 0 to -30dB T1 CESoPSN Packets (Structured or Structured with CAS): Packet Creation Time = 0.125ms x NF where NF = number of TDM frames per packet. 1.5.14 End-to-End Alarm Generation An end-to-end alarm generation mechanism exists in the EV kit to facilitate the following alarms: • Unframed: OOS is transmitted towards the near-end TDM interface in the event of: far-end LOS, AIS PDVT underflow/overflow • Fractional: Time slot/CAS configurable alarm pattern is transmitted towards the near-end TDM interface in the event of: far-end LOS, LOF, AIS PDVT underflow/overflow 16   Ethernet Uplink Transmit Level Q2.75V Q10% at 0 to 655ft with DSU 0dB, -7.5dB, -15dB, -22.5dB with CSU Line Impedance 100I Jitter Performance Per AT&T TR-62411, ITU-T G.824 Connector 8-pin RJ45 Standards IEEE 802.3, 802.3u, 802.1p and Q Data Rate 10/100/1000 half/full duplex Range Up to 100m on UTP Cat. 5 Type 10/100/1000 half/full-duplex port with autonegotiation support Connector 8-pin RJ45 Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 Table 1-2. Technical Specifications (continued) 2. Installation 2.1 Introduction Standards IEEE 802.3, Ethernet, 802.1p and Q Data Rate 10/100/1000 half/full duplex Range Up to 100m on UTP Cat. 5 Type 10/100/1000BASE-TX half/ full-duplex port with autonegotiation support Connector 8-pin RJ45 Type Standard DB9 connector Interface RS-232/V.24 (DCE) interface Data Rate 115.2kbps Data Bits 8 The EV kit contains jumpers and switches that provide preliminary configuration of the device. It should not be necessary to change these settings from the factory default. If it becomes necessary to change them, follow these instructions: Stop Bit 1 1) Open the EV kit enclosure. Flow Control None Clock Rate 2.048Mbps or 1.544Mbps 2) Set jumpers or switches located on the motherboard or on the daughter card. Connector 8-pin RJ45 Line Impedance 3) Close the EV kit enclosure. 120I or 100I 2.2.1 Opening the DS34S132 EV Kit Case Standard LVTTL input (square wave 0/3.3V) Connector BNC Loopbacks LLB and RLB LINK Off when line is not connected; On when line is connected Open the EV kit case to gain access. Caution: The EV kit contains components sensitive to electrostatic discharge (ESD). To prevent ESD damage, avoid touching the internal components. Before moving the jumpers, touch the EV kit frame. ACT Off when no activity; On when a frame is being transmitted or received on the line LOS On when there is no data in Rx LOF On when loss of frame is detected Power — 100 to 240V AC, 50Hz to 60Hz Height 11.1cm (4.375in) Physical Width 48.3cm (19in) To set the CPU daughter card jumpers: Depth 34.3cm (13.5in) 1) See Figure 2-2 to locate internal jumpers on the daughter card. Ethernet Management Control Station Clock Common Clock Diagnostics Ethernet Port Indicators E1/T1 Port Indicators The EV kit is delivered completely assembled and ready to use. Configure the EV kit using an ASCII terminal connected to the EV kit control port as described in 3. Operation. If problems are encountered, see 5. Troubleshooting and Diagnostics for test and diagnostics instructions. 2.2 Making Internal Settings To open the unit’s case: 1) Disconnect all cables from the EV kit. 2) Unscrew all the cover screws on the top and side panels of the unit. 3) Remove the top cover by pulling it straight up. 2.2.2 Setting the Internal Jumpers Internal jumpers are located on the motherboard and the CPU daughter card. To set the motherboard jumpers: 1) See Figure 2-1 to locate internal jumpers on the motherboard PCB. 2) Set the motherboard jumpers while referring to Table 2-1. 2) Set the daughter card jumpers referring to Table 2-2. Maxim Integrated   17 DS34S132 Evaluation Kit Evaluates: DS34S132 SW2 SW1 JMP1 JMP2 JMP3 CPU DAUGHTER CARD DS34S132 EV KIT DAUGHTER CARD JMP30 SW5 JMP34 Figure 2-1. Motherboard Jumper Locations Table 2-1. Motherboard Jumper and Switch Settings JUMPER FUNCTION FACTORY SETTING POSSIBLE SETTINGS JMP1 Controls DDRCLK PHY clock or BNC for DDR PHY clock JMP2 Selects clock for MAC PHY clock or BNC for MAC Unconnected JMP3 Selects clock for MAC PHY clock or not for MAC PHY clock JMP30 PWR ON Bypasses SW5 Connected JMP34 DS26518s’ MCLK selector Selects between LIUCLK output of DS34S132 and 2.048MHz oscillator SW1 Resets DS34S132 EV kit Resets DS34S132 daughter card N/A SW2 Board reset Resets motherboard N/A SW5 Powers down board This powers down the board if JMP30 is not connected N/A Oscillator Note: The motherboard includes additional factory-set jumpers and switches that must not be changed by the user. 18   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 J26 S2 MPC8313 S1 S4 S3 Figure 2-2. CPU Daughter Card Jumper Locations Table 2-2. CPU Daughter Card Jumper Settings JUMPER J26 FUNCTION SYS_CLK_IN selection POSSIBLE SETTINGS BNC or oscillator FACTORY SETTING Oscillator S1 Reset CPU card N/A S2 Unused N/A N/A S3 CPU control switches Do not change All on S4 CPU control switches Do not change All off N/A Note: The CPU board includes additional factory-set jumpers and switches that must not be changed by the user. Maxim Integrated   19 DS34S132 Evaluation Kit Evaluates: DS34S132 2.3 Connecting to the Ethernet Network Equipment The EV kit is connected to Ethernet network equipment through the 8-pin RJ45 port designated UPLINK. See Appendix A. Connector Wiring for the connector pin arrangement. Connect the EV kit to the Ethernet network equipment using a standard straight UTP cable. See Figure 2-3. 2.4 Connecting to the TDM Equipment The EV kit is connected to the TDM equipment through T1/E1 balanced RJ45 ports. See Appendix A. Connector Wiring for the connector pin arrangement. Connect the EV kit to the TDM equipment using standard straight E1/ T1 cables. See Figure 2-4. Figure 2-3. UPLINK Connector Figure 2-4. T1/E1 Connectors 20   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 2.5 Connecting to the Clock Sources 2.5.2 Connecting to the Common Clock Source 2.5.1 Connecting to the External Clock Source The EV kit is connected to a common clock source through an unbalanced BNC connector designated COMM CLK. Connect the EV kit to the common clock source using a using a 50I coaxial cable. The input signal must be LVTTL (square wave with 0V/3.3V levels). See Figure 2-6. The EV kit is connected to an external BITS clock source through a balanced RJ45 connector designated EXT CLK. See Appendix A. Connector Wiring for the connector pin arrangement. See Figure 2-5. Figure 2-5. EXT CLK Connector Figure 2-6. COMM CLK Connector Maxim Integrated   21 DS34S132 Evaluation Kit Evaluates: DS34S132 Figure 2-7. REF CLK Connector Figure 2-8. CONSOLE Connector 2.5.3 Connecting to the Reference Clock Source To connect to an ASCII terminal: The EV kit is connected to a reference clock source through an unbalanced BNC connector designated REF CLK. Connect the EV kit to the reference clock source using a using a 50I coaxial cable. The input signal must be LVTTL (square wave with 0V/3.3V levels). See Figure 2-7. 1) Connect a serial cable with a male 9-pin, D-type connector to the CONSOLE connector. 2.5.4 Connecting to an ASCII Terminal This section provides a detailed description of the front panel indicators and their functions, and explains the EV kit configuration using an ASCII terminal. See 4. Configuration for detailed explanations of parameters on the menus. The EV kit is connected to an ASCII terminal through a 9-pin, D-type, female connector designated CONSOLE. See Appendix A. Connector Wiring for the connector pin arrangement. See Figure 2-8. 22   2) Connect the other end of the serial cable to an ASCII terminal. 3. Operation Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 3.1 Front Panel Indicators The unit’s LEDs are located on the front panel (see Figure 3-1). Table 3-1 lists the functions of the EV kit LED indicators. 3.2 User Interface Software 3.2.1 Using the Control Port and an ASCII Terminal The EV kit can be configured and monitored using an ASCII terminal connected to the control port on the EV kit front panel. The control port is a V.24/RS-232 asynchronous DCE port terminated in a 9-pin, D-type female connector. The EV kit continuously monitors control port signals from the ASCII terminal and immediately responds to any input string received through this port. To access the user interface software using an ASCII terminal: 3) Set the port parameters of the control terminal PC to 115.2kbps, 8 bits/character, 1 stop bit, no parity. If available, set the terminal emulator to ANSI VT100 emulation (for optimal view of system menus). 4) At the end of the initialization and self-test, system software detects the part number of the TDMoP IC on the internal daughter card and displays it on the terminal screen as: login: The login ID is target and the password is password. After giving the password, the screen shows: ~ $ Write the following commands in sequence as shown: ~ $ su ~ $ password: root 1) Ensure all DS34S132 EV kit cables and connectors are properly connected. ~ $ ./ins132 2) Connect the DS34S132 EV kit to a PC equipped with ASCII terminal emulation software (for example, Windows Hyper Terminal or PuTTY). The Main Configuration (S132) menu is displayed in the terminal. ~ $ ./top32App top32App can be executed again after exiting the Main Configuration (S132) menu. Figure 3-1. DS34S132 EV Kit Front Panel Table 3-1. DS34S132 EV Kit LEDs and Controls NAME TYPE FUNCTION LOS Red LED On: Loss of signal (LEDs on the left refer to the top port, LEDs on the right refer to the bottom port). LOF Red LED On: Loss of E1/T1 synchronization has been detected. LINK Green LED On: Ethernet link is connected. Off: Ethernet link is disconnected. ACT Yellow LED On: Data is being transmitted/received at the Ethernet interface. Off: No data is being transmitted/received at the Ethernet interface. Note: LINK and ACT are not shown in Figure 3-1. Maxim Integrated   23 DS34S132 Evaluation Kit Evaluates: DS34S132 3.2.2 Using Telnet Through the Ethernet Management Port 2) Connect the MNG port of the DS34S132 EV kit to the local IP/Ethernet network. The EV kit can be configured and monitored remotely over an IP/Ethernet network. Currently, the DS34S132 only supports static IP (factory default is 10.16.34.18) so the user needs to program the correct IP address. Use the following steps to do this. Remember that the user only needs to do this once. 3) IP address was decided above. To configure the static IP address of the DS34S132 EV board: 1) Power the DS34S132 EV kit. 4) On a PC is connected to the IP/Ethernet network, run “cmd” to get a DOS-like text interface window. 5) At the command prompt, type telnet followed by the IP address determined in step 3. 6) At the login prompt, type target. At the password prompt, type password. Write the following commands in sequence as shown below: 2) Connect the MNG port of the EV kit to the local IP/ Ethernet network. ~ $ su 3) Use an ASCII terminal connected as previously described. ~ $ ./ins132 ~ $ password: root login: ~ $ ./top32App ~ # The login ID is root and the password is also root. After giving the password, the screen shows: Write the following commands in sequence as shown below: ~ # cd /etc/rc.d /etc/rc.d # vi rc.conf The user then needs to change the necessary parameters for ‘eth0’ (lines between ‘net interface 0’ and ‘net interface 1’). Once complete, save and exit. /etc/rc.d # reboot To access the user interface software using a telnet session: 1) Power the DS32S132 EV kit. SW Version The Main Configuration (S132) menu is displayed in the terminal. top32App can be executed again after exiting the Main Configuration (S132) menu. 3.2.3 Choosing Options To select a menu item, type the corresponding item number and then press Enter. If the selected item leads to another menu, the EV kit software displays the menu. If the selected item is a configurable parameter, the software displays descriptive text about the parameter and then, for parameters with only a few possible settings, displays a numbered list of possible values (e.g., 1: Enable, 2: Disable) and a prompt such as Please enter your choice:. For parameters with many possible values, the software displays descriptive text followed by 1.0.0 Main Configuration (S132) 1. 2. 3. 4. 5. 6. 7. 8. 9. Preconfig Configuration General Configuration Interface Configuration Bundle Configuration Bundle Management Restore Default Configurations Alarms Performance (PM) Utilities Please select item q: exit, s: save, ESC: previous menu, r or Enter: reprint screen Figure 3-2. Main Configuration Menu 24   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 a prompt at which a value can be entered (e.g., Please enter your clock rate:). The selection or value entered for each parameter is checked after pressing Enter, and only valid entries are accepted. If an entry is invalid, the software displays a prompt such as Please enter a valid choice: and gives another opportunity to enter a valid selection number or value. To navigate upward in the menu hierarchy toward the main menu, press Esc. 3.2.4 Redisplaying the Current Menu To redisplay the current menu, type r and press Enter or simply press Enter. 3.2.5 Saving Changes After changing the values of one or more parameters in a configuration menu, type s then Enter to save the changes and write them to the TDMoP IC. If changes are not saved in each menu, attempts to change parameters in other menus may not behave as expected. For example, changes in the Interface Configuration menu must be saved before activities in the Bundle Configuration menu behave correctly, especially when saving a bundle configuration. 4. Configuration This section discusses the EV kit configuration menus and explains their parameters: • Preliminary Configuration • Configuring General Parameters • Configuring TDM Interfaces Configuring E1 Interface Configuring T1 Interfaces • Configuring Bundles Configuring SAToP Bundles Configuring CESoPSN Bundles • Deleting Bundles • Displaying Active Bundles • Restoring Default Configurations 4.1 Preliminary Configuration For the convenience of the user, parameters that must be configured, such as link type, TDMoIP and IP versions, and clock recovery statistics, are given in the PreConfig Configuration menu. See Figure 4-1. PreConfig Configuration 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. Device Num (1 - 1) Max. Bundles (1 - 256) Link Type Bundle Number ID Location UDP Port Check VCCV OAM Mask [0 - 4] VCCV OAM Value MEF Ethernet Type MEF OAM Type TDMoIP Port Number 1 TDMoIP Port Number 2 VLAN Inner Label VLAN Outer Label Oscillator Type Common clock Freq Reference Clock Frequency Reference Clock Frequency PPM Offset Clock Recovery DSP File Name Driver Type 1 64 T1 Bundle Configuration Decides Yes 1 1000 88D8 889C 85E 85E 8100 9100 OCXO (Stratum 3E) 19440000 38880000 0 rom_code.asm.patch.txt Kernel Mode Please select item q: exit, s: save, ESC: previous menu, r or Enter: reprint screen Please enter your choice: Figure 4-1. Preliminary Configuration Menu Maxim Integrated   25 DS34S132 Evaluation Kit Evaluates: DS34S132 Table 4-1. Preliminary Configuration Parameter Descriptions PARAMETER DESCRIPTION POSSIBLE VALUES Device Num (1 - 1) Device number Default: 1 Max. Bundles (1 - 256) Maximum bundles Any number from 1–256 Default: 64 Link Type Specifies the type of TDM interface (link); all TDM interfaces on a TDMoP IC must be the same type E1, T1 Default: T1 Bundle Number ID Location Defines location of the bundle identification number 1: Bundle configuration decides (BCDR4) 2: Either UDP SRC or DST. port 3: Bundle in DST UDP PORT 4: Bundle in SRC UDP PORT 5: Combined SRC and DST UDP ports Default: Bundle Configuration Decides UDP Port Check Checks the UDP port number Yes, No Default: Yes VCCV OAM Mask [0 - 4] Indicates which of the 16 MSBs of the control word are used to identify VCCV OAM packets; the mask is active when one of the bits is set to 0 0–4 Default: 1 VCCV OAM Value Indicates the value of the 16 MSBs of the control word that identifies VCCV OAM packets 0–0xFFFF Default: 1000 MEF Ethernet Type Ethertype for MEF packets; must be set to a value greater than 0x5DC 0–0xFFFF Default: 88D8 MEF OAM Type Ethertype for MEF OAM packets; must be set to a value greater than 0x5DC 0–0xFFFF Default: 889C TDMoIP Port Number 1 Used to identify UDP/IP TDMoIP packets; its value is compared to either UDP_SRC_PORT_NUM or UDP_DST_PORT_NUM, according to Bundle Number ID Location (above) 0–0xFFFF Default: 85E TDMoIP Port Number 2 Used to identify UDP/IP TDMoIP packets; its value is compared to either UDP_SRC_PORT_NUM or UDP_DST_PORT_NUM, according to Bundle Number ID Location (above) 0–0xFFFF Default: 85E VLAN Inner Label Defines the tag protocol identifier (TPID) to use when using VLAN tags Standard (0x8100) Proprietary Default: Standard (8100) VLAN Outer Label Defines the tag protocol identifier (TPID) to use when using VLAN tags Standard (0x9100) Proprietary Default: Standard (9100) Oscillator Type The oscillator used as the clock recovery reference clock TCXO (Stratum 3) OCXO (Stratum 3E) Default: OCXO (Stratum 3E) Common clock Freq The common clock frequency supplied in the differential mode clock recovery Multiple of 8kHz Default: 19440000 26   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 Table 4-1. Preliminary Configuration Parameter Descriptions (continued) PARAMETER DESCRIPTION POSSIBLE VALUES Reference Clock Frequency Selects one of the 13 options for REFCLK frequency 1: 38.88MHz 2: 19.44MHz 3: 10MHz 4: 77.76MHz 5: 5MHz 6: 5.12MHz 7: 10.24MHz 8: 12.8MHz 9: 13MHz 10: 20MHz 11: 20.48MHz 12: 25MHz 13: 155.52MHz Default: 38880000 Reference Clock Frequency PPM Offset Selects one of the 13 options for PPM offset of the reference clock frequency Any number from 0–50 Default: 0 Clock Recovery DSP File Name DSP file that was used for recovering the clock Default: rom_code.asm.patch.txt Driver Type Type of the driver used 1. Kernel mode 2. User mode Default: Kernel Mode 4.2 Configuring General Parameters General Configuration MAIN MENU ↓ GENERAL CONFIGURATION 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Source Mac Address 1 Source Mac Address 2 Source IP 1 Source IP 2 Default Gateway Not Eth Type ARP Wrong IP Wrong IP ARP My IP Not TDMoIP Type Not UDP Type OAM Packet Bundle Not Exist Max HDLC Frame Size[1 - 1800] Ethernet Rate & Duplex OAM Configuration 08002E289D53 08002E286C0D 10.10.10.5 10.10.10.5 0.0.0.0 CPU CPU Discard CPU CPU CPU CPU Discard 1468 100M_FDX, ANEG > Please select item q: exit, s: save, ESC: previous menu, r or Enter: reprint screen Please enter your choice: Figure 4-2. General Configuration (Main Menu→General Configuration) Maxim Integrated   27 DS34S132 Evaluation Kit Evaluates: DS34S132 Table 4-2. General Configuration Parameter Descriptions PARAMETER DESCRIPTION POSSIBLE VALUES Source Mac Address 1 Port local MAC address Up to 12 alphanumeric characters Default: 08002E289D53 Source Mac Address 2 Second host MAC address. Up to 12 alphanumeric characters Default: 08002E2896C0D Source IP 1 Host IP address (see note). 0.0.0.0 to 255.255.255.255 Default: 10.10.10.5 Source IP 2 Second host IP address (see note). 0.0.0.0 to 255.255.255.255 Default: 10.10.10.5 Default Gateway IP address of default gateway. 0.0.0.0 to 255.255.255.255 Default: 0.0.0.0 Not Eth Type Specifies what to do with packets received from UPLINK port, where Ethertype does not match one of the following: IP, MPLS, ARP, MEF, MEF OAM, or CPU. Discard: Drops these packets CPU: Passes these packets to the CPU Default: CPU ARP Wrong IP Specifies what to do with ARP packets received from UPLINK port, where IP is different from source IP. Discard: Drops these packets CPU: Passes these packets to the CPU Default: CPU Wrong IP Specifies what to do with packets received from UPLINK port with IP different from all source IPs. Discard: Drops these packets CPU: Passes these packets to the CPU Default: CPU ARP My IP Specifies what to do with ARP packets received from UPLINK port, where IP is identical to source IP. Discard: Drops these packets CPU: Passes these packets to the CPU Default: CPU Not TDMoIP Type Specifies what to do with packets received from UPLINK port, where UDP destination/source port is not TDMoIP. Discard: Drops these packets CPU: Passes these packets to the CPU Default: CPU Not UDP Type Specifies what to do with packets received from UPLINK port, where protocol is not UDP. Discard: Drops these packets CPU: Passes these packets to the CPU Default: CPU OAM Packet Specifies what to do with TDMoIP OAM packets. Discard: Drops these packets CPU: Passes these packets to the CPU Default: CPU Bundle Not Exist Specifies what to do with packets received from UPLINK port, where bundle identifier is not one of the identifiers assigned in the TDMoP IC. Discard: Drops these packets CPU: Passes these packets to the CPU Default: Discard Max HDLC Frame Size [1 - 1800] Maximum size of HDLC packet in bytes (header and FCS are not included). 1–1800 for IP 1–1800 for MPLS Default: 1468 Ethernet Rate & Duplex If autonegotiation is enabled, rate and duplex must be configured to a value equal or greater than the rate and duplex mode of the network. If autonegotiation is disabled, the rate and duplex must be configured equal to the rate and duplex of the network. 1: 100 FDX ANEG 2: 1000 FDX ANEG 3: 100 FDX 4: 1000 FDX Default: 100M_FDX, ANEG OAM Configuration Selecting this options causes the OAM Configuration submenu to be displayed. — Note: Source IP 1 and Source IP 2 can reside in different subnets. However, the IP mask is used for both source IPs. Either Source IP 1 or Source IP 2 can be selected in the Bundle Configuration menu (see section 4.4 Configuring Bundles). 28   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 OAM Config Menu MAIN MENU ↓ GENERAL CONFIGURATION ↓ OAM CONFIGURATION 1. 2. 3. 4. 5. 7. 9. 11. 13. OAM OAM OAM OAM OAM OAM OAM OAM OAM Valid 2 ID 2 [0 - 0xFFFF] Valid 3 ID 3 [0 - 0xFFFF] Valid 4 Valid 5 Valid 6 Valid 7 Valid 8 Enable 24 Enable 0 Disable Disable Disable Disable Disable Please select item q: exit, s: save, ESC: previous menu, r or Enter: reprint screen Please enter your choice: Figure 4-3. OAM Configuration (Main Menu→General Configuration→OAM Configuration) MAIN MENU ↓ INTERFACE CONFIGURATION Please enter your Choice: 3 Please enter TDM Link Number [1 - 32]: Figure 4-4. TDM Interface Selection (Main Menu→Interface Configuration) Table 4-3. OAM Configuration Parameter Descriptions PARAMETER DESCRIPTION POSSIBLE VALUES OAM Valid n Enables/disables OAM ID n (2 P n P 8). Enable Disable Default: Disable OAM ID n [0 - 0xFFFF] Specifies OAM ID n (2 P n P 8). These IDs are bundle IDs for UDP/ IP-specific OAM. If the bundle ID of an incoming packet matches an enabled OAM ID, the packet classifier in the TDMoP IC considers the packet to be an OAM packet and discards or forwards it to the CPU as specified by the OAM packet field described above. 0–0xFFFF Default: 0 4.3 Configuring TDM Interfaces The number of TDM interfaces available depends on the TDMoP IC on the daughter card. A DS34S132 has 32 TDM interfaces. The user interface software only allows configuration of the number of TDM interfaces actually supported by the installed IC. Maxim Integrated To configure a TDM interface, select Interface Configuration from the Main Configuration (S132) menu and enter the interface number at the prompt (Figure 4-4). The Interface Configuration menu is then displayed, either Figure 4-5 (E1) or Figure 4-6 (T1), depending on the setting of the Link Type parameter in the PreConfig Configuration menu.   29 DS34S132 Evaluation Kit Evaluates: DS34S132 4.3.1 Configuring E1 Interfaces E1 Interface Configuration for link 1 MAIN MENU ↓ INTERFACE CONFIGURATION ↓ E1 INTERFACE CONFIGURATION 1. 2. 3. 4. 6. 7. 8. 9. 10. 11. 26. 32. 33. 38. 39. 40. 41. Frame Type Rx Config Gain Limit OOS Code Type Data TX/RX OOS[0 - 0xFF] TX/RX OOS Signal Mask Clock Source Link Sync Connect/Disconnect CRC4 IF Type Master’s Side Clock Source Network Type Clock Recovery Debug Tool ADCL PPM One or Two Clock Mode Adaptive or Differential Mode RTP Timestamp Generation Mode UnFramed Short Haul OOS Code 7F Space Internal CCITT Connect No Balanced Stratum 1 Router based Extended Statistics 0.000000 One Clock Adaptive Bit Please select item q: exit, s: save, ESC: previous menu, r or Enter: reprint screen Please enter your choice: NOTE: THE SETTINGS FOR SOME PARAMETERS IN THIS CONFIGURATION MENU DETERMINE WHETHER OR NOT OTHER PARAMETERS IN THE MENU ARE DISPLAYED. FOR EXAMPLE, IF RECOVERY CLK MODE IS SET TO AUTO, THEN ITEMS 13–25 AND 27–31 ARE NOT DISPLAYED BECAUSE THEIR VALUES ARE IGNORED IN THAT MODE. THE PARAMETER DESCRIPTIONS IN TABLE 4-4 HAVE NOTES INDICATING THE NECESSARY CONDITIONS FOR A PARAMETER TO BE DISPLAYED. SEE THE ACQUISITION SWITCH PARAMETER. Figure 4-5. E1 Interface Configuration (Main Menu→Interface Configuration→E1 Interface Configuration) Table 4-4. E1 Interface Configuration Parameter Descriptions PARAMETER DESCRIPTION POSSIBLE VALUES Framing mode and operation mode for each configuration. Note: Before changing the E1 frame type, you must close all bundles assigned to the link. Unframed: Framer is configured to pass-through mode and the operation mode is set to unframed. Framed: The E1 framer is set for simple FAS/NFAS framing and the TDMoP block is set to fractional. Multiframe: The E1 framer is set to MF mode and the TDMoP block is set to fractional with CAS. Default: UnFramed Rx Config Gain Limit Determines the maximum attenuation of the receive signal that can be compensated for by the E1 link receive path, to obtain the BER performance required by the standards. Long Haul: Maximum attenuation of 36dB. Short Haul: Maximum attenuation of 10dB. This configuration can actually improve the performance when operating over relatively short line sections, especially when operating over multipair cables. In such cables, significant interference is generated by the signals carried by other pairs, and therefore a weak desired signal can be masked by the interference. Default: Short Haul OOS Code Type Defines what to send if an OOS state occurred. OOS Code: OOS code is sent Default: OOS code Frame Type 30   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 Table 4-4. E1 Interface Configuration Parameter Descriptions (continued) PARAMETER DESCRIPTION Data TX/RX OOS [0 - 0xFF] Can be applied to time slots transmitted towards the ETH network when loss of signal, loss of frame or AIS is detected at the E1 line. Can also be applied to time slots transmitted toward the E1 line when packet receive buffer overrun or underrun occurs. In unframed mode, OOS state results in AIS transmission. This is applied when an LOS is detected at the E1 line, or when packet receive buffer overrun or underrun occurs. 0–FF Default: 7F Out-of-service signaling method. OOS signal is sent in the Ethernet direction when loss of signal, loss of frame, or AIS is detected at the E1 line. The OOS signal is also sent toward the E1 line when packet receive buffer overrun or underrun occur. Space: Transmit CAS all 0s, when the Ethernet or TDM link is down Mark: Transmit CAS all 1s, when the Ethernet or TDM link is down Space + Mark: Transmit all 0s in CAS for the first 2.5s, then switch to all 1s Mark + Space: Transmit all 1s in CAS for the first 2.5s, then switch to all 0s Default: Space Clock Source Defines transmit clock source used by the interface. Adaptive Recovery: Clock recovery regeneration from UPLINK LIU Loopback: T1 recovered receive clock is used as the transmit clock Global Adaptive Recovery: Selecting recovered clock from port 1 (future version will select one of the 32 ports) EXTCLK0: Not supported (future version will select one of the 32 ports) EXTCLK1: Not supported (future version will select one of the 32 ports) Default: Loopback Link Sync Selects the E1 local sync loss alarm recovery time. CCITT: Complies with ITU‑Rec.G.732 62411: 10s Sync Fast: 1s Default: CCITT Connect/ Disconnect Defines if link is connected. Connect: Link is connected Disconnect: Link is disconnected Default: Connect CRC4 Enables the generation of CRC bits (in accordance with the CRC-4 polynomial specified by ITU-T Rec. G.704) for the frames transmitted on the E1 link, and the checking of the CRC bits carried by the received E1 link frames. No: CRC-4 option is disabled Yes: CRC-4 option is enabled Default: No IF Type Defines E1 interface type. Balanced, Unbalanced Default: Balanced TX/RX OOS Signal Mask Maxim Integrated POSSIBLE VALUES   31 DS34S132 Evaluation Kit Evaluates: DS34S132 Table 4-4. E1 Interface Configuration Parameter Descriptions (continued) PARAMETER DESCRIPTION POSSIBLE VALUES Model used for simulating distribution of the packet delay variation in the network. Router-based Switch-based GenDSL based Default: Router based Clock Recovery Debug Tool Enables or disables clock recovery statistics collection tools. 1: Extended Statistics 2: Auto Debug Tool 3: Manual Debug Tool 4: Disable Default: Extended statistics ADCL PPM Adding PPM with ADCL clock. Default: 0.000000 One or Two Clock Mode Using one-clock or two-clock mode. 1: One Clock (TCLKO pin→RCLK) 2: Two Clock (RCLK pin→RCLK) Default: One Clock Adaptive or Differential Mode Enabling adaptive or differential mode of operation per port. 1: Adaptive mode 2:Differential mode Default: Adaptive RTP Timestamp Generation Mode Putting timestamp when the RTP is enabled based on bit, byte, or frame byte mode. 1: Bit 2: Byte 3: Frame Default: Bit Network Type 4.3.2 Configuring T1 Interfaces T1 Interface Configuration for link 1 MAIN MENU ↓ INTERFACE CONFIGURATION ↓ T1 INTERFACE CONFIGURATION 1. 2. 3. 4. 6. 7. 8. 9. 10. 11. 12. 26. 32. 33. 38. 39. 40. 41. Frame Type Rx Config Gain Limit OOS Code Type Data TX/RX OOS[0 - 0xFF] TX/RX OOS Signal Mask Clock Source Link Sync Connect/Disconnect DSU / CSU DSU / CSU Mask Config Code Master’s Side Clock Source Network Type Clock Recovery Debug Tool ADCL PPM One or Two Clock Mode Adaptive or Differential Mode RTP Timestamp Generation Mode UnFramed Short Haul OOS Code 7F Space Loopback Sync Fast Connect DSU Mask 0 B8ZS Stratum 1 Router based Extended Statistics 0.000000 One Clock Adaptive Bit Please select item q: exit, s: save, ESC: previous menu, r or Enter: reprint screen Please enter your choice: NOTE: THE SETTINGS FOR SOME PARAMETERS IN THIS CONFIGURATION MENU DETERMINE WHETHER OR NOT OTHER PARAMETERS IN THE MENU ARE DISPLAYED. FOR EXAMPLE, IF RECOVERY CLOCK MODE IS SET TO AUTO, THEN ITEMS 13–25 AND 27–31 ARE NOT DISPLAYED BECAUSE THEIR VALUES ARE IGNORED IN THAT MODE. THE PARAMETER DESCRIPTIONS IN TABLE 4-5 HAVE NOTES INDICATING THE NECESSARY CONDITIONS FOR A PARAMETER TO BE DISPLAYED. SEE THE ACQUISITION SWITCH PARAMETER. Figure 4-6. T1 Interface Configuration (Main Menu→Interface Configuration→T1 Interface Configuration) 32   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 Table 4-5. T1 Interface Configuration Parameter Descriptions PARAMETER DESCRIPTION POSSIBLE VALUES Framing mode and operation mode for each configuration. Note: Before changing the T1 frame type, you must close all bundles assigned to the link. Unframed: Framer is configured to passthrough mode and the operation mode is set to unframed. ESF: Framer is configured to T1-ESF mode. Operation mode is set by the robbed bit field to either fractional or fractional with CAS. SF: Framer is configured to T1-SF mode. Operation mode is set by the robbed bit field to either fractional or fractional with CAS. Default: UnFramed Rx Config Gain Limit Determines the maximum attenuation of the receive signal that can be compensated for by the T1 link receive path, to obtain the BER performance required by the standards. Long Haul: Maximum attenuation of 36dB. Short Haul: Maximum attenuation of 10dB. This configuration can actually improve the performance when operating over relatively short line sections, especially when operating over multipair cables. In such cables, significant interference is generated by the signals carried by other pairs, and therefore a weak desired signal can be masked by the interference. Default: Short Haul OOS Code Type Inserted into unassigned time slots by the system at the transmit path towards the T1 equipment. This parameter is not displayed when the frame type is set to unframed. OOS Code: OOS code is sent. Default: OOS Code Data TX/RX OOS [0 - 0xFF] Can be applied to time slots transmitted towards the ETH network when loss of signal, loss of frame, or AIS is detected at the T1 line. Can also be applied to time slots transmitted towards the T1 line when a packet receive buffer overrun or underrun occurs. In unframed mode, voice/data OOS state results in AIS transmission. This is applied when an LOS is detected at the T1 line, or when a packet receive buffer overrun or underrun occurs. 00–FF Default: 7F Out-of-service signaling method. OOS signal is sent in the Ethernet direction when loss of signal, loss of frame, or AIS is detected at the T1 line. The OOS signal is also sent toward the T1 line when packet receive buffer overrun or underrun occur. Space: Transmitting CAS all 0s, when the Ethernet or TDM link is down. Mark: Transmitting CAS all 1s, when the Ethernet or TDM link is down. Space + Mark: Transmitting all 0s in CAS for the first 2.5s, then switching to all 1s. Mark + Space: Transmitting all 1s in CAS for the first 2.5s, then switching to all 0s. Default: Space Frame Type TX/RX OOS Signal Mask Maxim Integrated   33 DS34S132 Evaluation Kit Evaluates: DS34S132 Table 4-5. T1 Interface Configuration Parameter Descriptions (continued) PARAMETER DESCRIPTION POSSIBLE VALUES Clock Source Defines transmit clock source used by the interface. Adaptive Recovery: Clock recovery regeneration from UPLINK. LIU Loopback: T1 recovered receive clock is used as the transmit clock Global Adaptive Recovery: Selecting reovered clock from port 1 (future version will select one of the 32 ports). EXTCLK0: Not supported (future version will select one of the 32 ports). EXTCLK1: Not supported (future version will select one of the 32 ports). Default: Loopback Link Sync Selects the T1 red alarm recovery time. Sync Fast: 1s 62411: 10s Default: Sync Fast Connect/ Disconnect Defines if link is connected. Connect: Link is connected. Disconnect: Link is disconnected. Default: Connect DSU / CSU — CSU: If the port interface operates as a CSU, it is necessary to adjust the T1 output transmit level for reliable operation of the network and for compliance with FCC Rules Part 68A. This adjustment is used to minimize the interference caused by a local transmit signal to other users that transmit their signals on other pairs of the same cable. The required setting depends mainly on the length of the cable that connects between the T1 port and the first repeater down the link. Repeaters are usually located every mile, and, therefore, they are designed to optimally handle signals attenuated by one-mile length of cable. If the T1 port is closer, the repeater receives a T1 signal at a higher level. This does not significantly improve handling of the T1 signal, but certainly increases the interference coupled from the T1 pair to repeaters that serve other pairs in the cable. To prevent this, an attenuation value can be selected that brings the T1 signal level closer to the expected repeater signal level. This is achieved by enabling circuitry in the T1 transmitter that preattenuates the signal by 7.5dB, 15dB, or 22.5dB, effectively emulating 1000ft, 2000ft, or 3000ft of cable. DSU: In this case, the transmit signal mask can be selected in accordance with the transmit line length, to meet DSX-1 requirements, as specified by AT&T CB-119, or operation in accordance with FCC Rules Part 68. For compliance with DSX-1 specifications per AT&T CB-119 and ANSI T1.102-1987, select the value corresponding to the length of the cable (in feet) connected between the T1 port connector and network entry point. Default: DSU 34   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 Table 4-5. T1 Interface Configuration Parameter Descriptions (continued) PARAMETER DESCRIPTION POSSIBLE VALUES DSU / CSU Mask — CSU: Mask 0: No attenuation. Mask 1: Attenuation of 7.5dB relative to nominal. Mask 2: Attenuation of 15dB relative to nominal. Mask 3: Attenuation of 22.5dB relative to nominal. DSU: Mask 0: 000–133ft Mask 1: 133–266ft Mask 2: 266–399ft Mask 3: 399–533ft Mask 4: 533–655ft Default: Mask 0 Config Code Specifies the line coding. B8ZS AMI Default: B8ZS Master’s Side Clock Source The type of the master’s side source clock. Stratum 1 Stratum 2 Stratum 3 Stratum 3E Stratum 4 Default: Stratum 1 Network Type Model used for simulating distribution of the packet delay variation in the network. Router based Switch based GenDSL based Default: Router based Clock Recovery Debug Tool Enables or disables clock recovery statistics collection tools. 1: Extended Statistics 2: Auto Debug Tool 3: Manual Debug Tool 4: Disable Default: Extended Statistics ADCL PPM Adding PPM with ADCL clock. Default: 0.000000 One or Two Clock Mode Using one-clock or two-clock mode. 1: One Clock (TCLKO pin→RCLK) 2: Two Clock (RCLK pin→RCLK) Default: One Clock Adaptive or Differential Mode Enabling adaptive or differential mode of operation per port. 1: Adaptive mode 2: Differential mode Default: Adaptive RTP Timestamp Generation Mode Putting timestamp when the RTP is enabled based on bit, byte, or frame byte mode 1: Bit 2: Byte 3: Frame Default: Bit Maxim Integrated   35 DS34S132 Evaluation Kit Evaluates: DS34S132 4.4 Configuring Bundles 5) In the Bundle Configuration menu, select 1. Bundle Type to specify the bundle type: HDLC, SAToP, or CES. To configure a bundle: 1) Configure general parameters (see 4.2 Configuring General Parameters). 2) Configure TDM interface (see 4.3 Configuring TDM Interfaces). 3) From the Main Configuration (S132) menu (Figure 3-2) select 4. Bundle Configuration. 4) Enter a bundle number at the prompt. Bundle number can be any number from 0–4095. 6) Proceed with bundle configuration according to the bundle type (see 4.4.1 Configuring SAToP Bundles and 4.4.2 Configuring CESoPSN Bundles). Up to 256 bundles can be assigned in the TDMoP IC in E1 or T1 mode. 4.4.1 Configuring SAToP Bundles See Figure 4-7 and Table 4-6 for SAToP bundle options. 4.4.2 Configuring CESoPSN Bundles Bundle Configuration for ID 2 MAIN MENU ↓ BUNDLE CONFIGURATION ↓ SAToP BUNDLE CONFIGURATION 1. 2. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 35. 36. 37. 38. 44. 45. Bundle Type Assign this Bundle to PCM port TX Bundle Destination RX Bundle Destination TX Bundle Number[0 - 65535] RX Bundle Number[0 - 65535] Source IP Address Destination Main MAC Address Destination IP Address Next Hop IP IP ToS[0 - 255] IP TTL[0 - 255] Number of VLAN Tags[0 - 2] PSN Type Switches Sanity Check Clock Recovery Differential Time (usec)[1 - 512000] Max Buffer Size (usec)[0 - 512000] L Bit & OOS Redundant RTP Mode Next Hop Type Enable JB Reset Window Size[2 - 127] Reordering Size in Bytes[24 - 1600] Eth Cond Octet Type TDM Cond Octet Type TX Bundle Number Location at UDP port RX Bundle Number Location at UDP port SAToP 1 Ethernet PCM 1 1 IP 1 0020D224A346 10.10.10.5 0.0.0.0 0 128 0 IP Discard Yes 5000 15000 OOS Mode Conditioning Disable Disable IP On N Times 83 Yes 965 Octet A Octet A Source Source Please select item q: exit, s: save, ESC: previous menu, r or Enter: reprint screen NOTE: THE SETTINGS FOR SOME PARAMETERS IN THIS CONFIGURATION MENU (FOR EXAMPLE, BUNDLE TYPE AND PSN TYPE) DETERMINE WHETHER OR NOT OTHER PARAMETERS IN THE MENU ARE DISPLAYED. THEREFORE, IT IS NORMAL TO HAVE GAPS IN THE ITEM NUMBERING, SUCH AS HAVING NOTHING LISTED BETWEEN ITEMS 14 AND 20. THE PARAMETER DESCRIPTIONS IN TABLE 4-6 HAVE NOTES INDICATING THE NECESSARY CONDITIONS FOR A PARAMETER TO BE DISPLAYED. SEE THE IP TOS PARAMETER. Figure 4-7. SAToP Bundle Configuration (Main Menu→Bundle Configuration→SAToP Bundle Configuration) 36   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 Table 4-6. SAToP Bundle Parameter Descriptions PARAMETER DESCRIPTION POSSIBLE VALUES Bundle Type Select the bundle type. HDLC SAToP CES Assign this Bundle to PCM port Number of the TDM port to which the bundle is assigned. 1–32 TX Bundle Destination Destination of the Tx data flow toward the ETH port. Note: The Tx bundle destination cannot be changed after the bundle configuration has been saved. Ethernet: TDM to Ethernet CPU: TDM to CPU Cross Connect: Don’t support yet Default: Ethernet RX Bundle Destination Destination of the Rx data flow from the ETH port. Note: The Rx bundle destination cannot be changed after the bundle configuration has been saved. CPU: CPU PCM: TDM (PCM bus) Discard: Discarded Default: PCM TX Bundle Number [0 - 65535] Number of the desired Tx bundle. Default: 2 Rx Bundle Number [0 - 65535] Number of the desired Rx bundle. Note: Must be unique for each bundle ID. Default: 2 Source IP Address Assign the bundle one of the source IP addresses configured in the General Configuration menu. IP 1, IP 2 Default: IP 1 Destination Main MAC address MAC address of destination device. Note: If the destination Main MAC address is different from the default value, the MAC is not learned in the ARP process. Default: 000000000000 Destination IP Address IP address of the destination device. 0.0.0.0 – 255.255.255.255 Next Hop IP The Next Hop parameter should be used when the Destination IP Address is not in the device subnet. In such cases the Ethernet packet is sent to the Next Hop IP. The default value of the Next Hop field is the default gateway. Note: The Next Hop must be in the same subset as the Source IP address of the bundle ID. 0.0.0.0 – 255.255.255.255 IP ToS [0 - 255] Sets the IP ToS field in the IP ETH packets leaving the EV kit. The ToS setting defines the whole byte, since different vendors could use different bits to tag packets for traffic prioritization. ToS assignment applies to all ETH packets leaving the EV kit for this bundle. Note: This parameter is displayed only if PSN Type is set to IP. 0–255 Default: 0 IP TTL [0 - 255] Sets the IP TTL field in the IP packets transmitted by the device. TTL assignment applies to all ETH packets leaving the EV kit for this bundle. Note: This parameter is displayed only if PSN Type is set to IP. 0–255 Default: 128 Maxim Integrated   37 DS34S132 Evaluation Kit Evaluates: DS34S132 Table 4-6. SAToP Bundle Parameter Descriptions (continued) PARAMETER DESCRIPTION POSSIBLE VALUES MPLS TTL Sets the MPLS TTL field in the packets transmitted by the device. TTL assignment applies to all MPLS packets leaving the EV kit for this bundle. Note: This parameter is displayed only if PSN Type is set to MPLS. 0–255 Default: 128 Number of VLAN Tags [0 - 2] Defines if VLAN tagging is enabled, and how many VLAN tags are used. 0: No VLAN Tag 1: One VLAN tag 2: Two VLAN tags (stacked) Default: 0 VLAN Protocol Defines the tag protocol identifier (TPID) to use when using VLAN tags. Note: This parameter is displayed only if Number of VLAN tags is set to 1 or 2. Standard (0x8100) Proprietary Default: Standard (0x8100) VLAN ID 1 VLAN identifier, uniquely identifying the VLAN to which the Ethernet packet belongs. Note: This parameter is displayed only if Number of VLAN tags is set to 1 or 2. 1–4095 Default: 1 VLAN ID 2 VLAN identifier, uniquely identifying the VLAN to which the Ethernet packet belongs. Note: This parameter is displayed only if the Number of VLAN tags is set to 2. 1–4095 Default: 1 VLAN 1 Priority Sets the priority of the packet in the virtual LAN. Note: This parameter is displayed only if the Number of VLAN tags is set to 1 or 2. 0–7 Default: 0 VLAN 2 Priority Sets the priority of the packet in the virtual LAN. Note: This parameter is displayed only if the Number of VLAN tags is set to 2. 0–7 Default: 0 Defines the header encapsulated in the packets leaving the DS34S132 EV kit IP: UDP/IP header MPLS: MPLS header L2TPV3: L2TPV3/IP header Ethernet: MEF header Default: IP Sanity check between the received packet length and the length according to bundle configuration (length mismatch). CPU: Sends the packets that fail the sanity check to the CPU Discard: Drops the packets that fail the sanity check Default: Discard Determines whether this bundle is used by the clock recovery mechanism. Yes: Bundle is used by clock recovery mechanism No: Bundle is not used by clock recovery mechanism Default: No PSN Type Switches Sanity Check Clock Recovery 38   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 Table 4-6. SAToP Bundle Parameter Descriptions (continued) PARAMETER DESCRIPTION POSSIBLE VALUES Differential Time (usec) [1 - 51200] Desired depth of the jitter buffer. 1–512000μs Default: 5000 Max Buffer Size (usec) [1 - 51200] Defines the maximum size of the jitter buffer. When this parameter is set to zero, the maximum jitter buffer size equals (2 x PDVT) + (2 x packet fill). 0–512000μs Default: 0 L Bit & OOS Defines how the OOS condition at the TDM interface is transmitted towards the Ethernet side. 1. OOS Mode Conditioning: OOS condition is reported by the OOS (ETH cond data) code and L-bit of the TDMoIP frame. 2. OOS Disable: OOS condition is not reported, but user data with L-bit keeps on being sent towards the Ethernet interface. 3. OOS Mode Tx Off: OOS condition is not reported and faulty user data is not transmitted towards the Ethernet interface. 4. OOS Mode Conditioning with JB reset: OOS condition is reported by the OOS (ETH cond data) code and L-bit of the TDMoIP frame. Reset jitter buffer when L-bit cleared. 5. OOS Disable with JB reset: OOS condition is not reported, but user data with L-bit keeps on being sent towards the Ethernet interface. Reset jitter buffer when L-bit cleared. 6. OOS Mode Tx Off with JB reset: OOS condition is not reported and faulty user data is not transmitted towards the Ethernet interface. Reset jitter buffer when L-bit cleared. Redundant Defines whether this bundle is a redundant bundle. Note: The bundle redundancy cannot be changed after the bundle configuration has been saved. Redundant mode not supported Enable: Current bundle is redundant Disable: Current bundle is not redundant Default: Disable RTP Mode Determines if an RTP header is used for the bundle. Must be used for common clock mode. Enable: RTP header is used Disable: RTP header is not used Default: Disable Next Hop Type Must be set to MAC for next hops that do not reply to ARP requests. IP MAC Default: IP Maxim Integrated   39 DS34S132 Evaluation Kit Evaluates: DS34S132 Table 4-6. SAToP Bundle Parameter Descriptions (continued) PARAMETER DESCRIPTION POSSIBLE VALUES Enable JB Reset A mechanism that enables setting an optimum level for the jitter buffer working level. It enables the reset of a bundle, until a satisfactory jitter buffer level is reached, to minimize the delay. Off: Bundle reset is disabled and the working level of the jitter buffer is determined by the timing the bundle was first opened On N Times: Up to N times of bundle reset is allowed Endless: Bundle reset is allowed with unlimited number of resets Default: On N Times Window Size [2 - 127] The maximum number of conditioning Ethernet packets that can be inserted upon a loss of received Ethernet packets. If the difference in packet SN is greater than the configured window, there is no insertion of conditioning packets. 2–127 Default: 83 Number Of Outer Cookies Determines if L2TPV3 cookies are used and how many. Note: This parameter is displayed only when PSN Type = L2TPV3. 0: L2TPV3 cookies are not used 1: One L2TPV3 cookie is used 2: Two L2TPV3 cookies are used Default: 0 Cookie 1 Optional field that contains a randomly selected value used to validate association of the packet with the expected bundle identifier. Note: This parameter is displayed only when PSN Type = L2TPV3 and Number of Outer Cookies is 1 or 2. 0–4294967295 Default: 0 Cookie 2 Optional field that contains a randomly selected value used to validate association of the packet with the expected bundle identifier. Note: This parameter is displayed only when PSN Type = L2TPV3 and Number of Outer Cookies is 2. 0–4294967295 Default: 0 Determines if MPLS outer labels are used and how many. Note: This parameter is displayed only when PSN Type = MPLS. 0: MPLS outer labels not used 1: One MPLS outer label is used 2: Two MPLS outer labels are used Default: 0 MPLS Outer Label (only when not equal to 0) identifies the MPLS LSP, which is used to tunnel the TDM packets through the MPLS network. Note: When equal to 0, only the Inner Label exists. This parameter is displayed only when PSN Type = MPLS and Number of Outer Labels is 1 or 2. 0–1048575 Default: 0 MPLS Outer Label (only when not equal to 0) identifies the MPLS LSP, which is used to tunnel the TDM packets through the MPLS network. Note: When equal to 0, only the Inner Label exists. This parameter is displayed only when PSN Type = MPLS and Number of Outer Labels is 2. 0–1048575 Default: 0 Number Of Outer Labels MPLS Outer Label 1 MPLS Outer Label 2 40   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 Table 4-6. SAToP Bundle Parameter Descriptions (continued) PARAMETER DESCRIPTION POSSIBLE VALUES Sets the value of the MPLS experimental bits. Note: This parameter is displayed only when PSN Type = MPLS. 0–7 Default: 0 Reordering Determines whether to reorder received misordered packets. Yes: Received misordered packets are reordered No: Received misordered packets are not reordered Default: Yes Size in Bytes [24 - 1600] SAToP payload size in bytes. 24–1600 Default: 965 Conditioning octet used in the Ethernet direction when no data is available. Octet A Octet B Octet C Octet D Default: Octet A TDM Cond Octet Type Conditioning octet used in the TDM direction when no data is available. Octet A Octet B Octet C Octet D Default: Octet A RTP Source Identifier The RTP header Source Identifier value for transmitted packet. Note: This parameter is displayed only when RTP Mode is Enabled. 0–4294967295 Default: 111111111 RTP Payload The RTP header Payload value for transmitted packet. Note: This parameter is displayed only when RTP Mode is Enabled. 0–255 Default: 96 Indicating the location of the Transmitting Bundles UDP port. Source: UDP port number is at Source Port side Destination: UDP port number is at Destination Port side Indicating the location of the Receiving Bundles UDP port. Source: UDP port number is at Source Port side Destination: UDP port number is at Destination Port side Experimental Bits Eth Cond Octet Type TX Bundle Number Location at UDP port RX Bundle Number Location at UDP port Maxim Integrated   41 DS34S132 Evaluation Kit Evaluates: DS34S132 See Figure 4-8 and Table 4-7 for CESoPSN bundle options. 4.5 Deleting Bundles Bundle Configuration for ID 2 MAIN MENU ↓ BUNDLE CONFIGURATION ↓ CES BUNDLE CONFIGURATION 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 35. 36. 37. 38. 39. 45. 46. 47. Bundle Type Assign this Bundle to PCM port Timeslot Assignment [1-24] TX Bundle Destination RX Bundle Destination TX Bundle Number[0 - 65535] RX Bundle Number[0 - 65535] Source IP Address Destination Main MAC Address Destination IP Address Next Hop IP IP ToS[0 - 255] IP TTL[0 - 255] Number of VLAN Tags[0 - 2] PSN Type Switches Sanity Check Clock Recovery Differential Time (usec)[1 - 512000] Max Buffer Size (usec)[0 - 512000] L Bit & OOS Redundant RTP Mode Next Hop Type Enable JB Reset Window Size[2 - 127] Payload Type Reordering Number of Frames[1 - 1500] Eth Cond Octet Type TDM Cond Octet Type Far End Interface Type TX Bundle Number Location at UDP port RX Bundle Number Location at UDP port CES 2 1-24 Ethernet PCM 2 2 IP 1 0020D224A346 10.10.10.5 0.0.0.0 0 128 0 IP Discard No 5000 15000 OOS Mode Conditioning Disable Disable IP On N Times 83 Data Yes 40 Octet A Octet A ESF Source Source Please select item q: exit, s: save, ESC: previous menu, r or Enter: reprint screen NOTE: THE SETTINGS FOR SOME PARAMETERS IN THIS CONFIGURATION MENU (FOR EXAMPLE, BUNDLE TYPE AND PSN TYPE) DETERMINE WHETHER OR NOT OTHER PARAMETERS IN THE MENU ARE DISPLAYED. THEREFORE, IT IS NORMAL TO HAVE GAPS IN THE ITEM NUMBERING, SUCH AS HAVING NOTHING LISTED BETWEEN ITEMS 14 AND 20. THE PARAMETER DESCRIPTIONS IN TABLE 4-7 HAVE NOTES INDICATING THE NECESSARY CONDITIONS FOR A PARAMETER TO BE DISPLAYED. SEE THE IP TOS PARAMETER. Figure 4-8. CESoPSN Bundle Configuration (Main Menu→Bundle Configuration→CES Bundle Configuration) 42   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 Table 4-7. CESoPSN Bundle Parameter Descriptions PARAMETER DESCRIPTION POSSIBLE VALUES Bundle Type Select the bundle type. HDLC SAToP CES Assign this Bundle to PCM port Number of the TDM port to which the bundle is assigned. 1–32 Timeslot Assignment [1 - 24] Assigns time slots to the previously selected bundle, for example, 1–5, 7, 8, 9, 12–15. T1: 1–24 E1: 1–31 TX Bundle Destination Destination of the Tx data flow toward the ETH port. Note: The Tx bundle destination cannot be changed after the bundle configuration has been saved. Ethernet: TDM to Ethernet CPU: TDM to CPU Cross connect: TDM to TDM (not supported yet) Default: Ethernet RX Bundle Destination Destination of the Rx data flow from the ETH port Note: The Rx bundle destination cannot be changed after the bundle configuration has been saved. CPU: CPU PCM: TDM (PCM bus) Discard: Discarded Default: PCM TX Bundle Number [0 - 65535] Number of the desired Tx bundle. Default: 2 RX Bundle Number [0 - 65535] Number of the desired Rx bundle. Note: Must be unique for each bundle ID. Default: 2 Source IP Address Assign the bundle one of the source IP addresses configured in the General Configuration menu. IP 1, IP 2 Default: IP 1 Destination Main MAC Address MAC address of destination device. Note: If the destination Main MAC address is different from the default value, the MAC is not learned in the ARP process. Default: 0020D224A346 Destination IP Address IP address of the destination device 10.10.10.5 Next Hop IP The Next Hop parameter should be used when the Destination IP Address is not in the device subnet. In such cases the Ethernet packet is sent to the Next Hop IP. The default value of the Next Hop field is the default gateway. Note: The Next Hop must be in the same subset as the Source IP address of the bundle ID. 0.0.0.0 IP ToS [0 - 255] Sets the IP ToS field in the IP ETH packets leaving the EV kit. ToS setting defines the whole byte, since different vendors could use different bits to tag packets for traffic prioritization. The ToS assignment applies to all ETH packets leaving the EV kit for this bundle. Note: This parameter is displayed only if PSN Type is set to IP. 0–255 Default: 0 Maxim Integrated   43 DS34S132 Evaluation Kit Evaluates: DS34S132 Table 4-7. CESoPSN Bundle Parameter Descriptions (continued) PARAMETER DESCRIPTION POSSIBLE VALUES IP TTL [0 - 255] Sets the IP TTL field in the IP packets transmitted by the device. TTL assignment applies to all ETH packets leaving the EV kit for this bundle. Note: This parameter is displayed only if PSN Type is set to IP. 0–255 Default: 128 MPLS TTL Sets the MPLS TTL field in the packets transmitted by the device. TTL assignment applies to all MPLS packets leaving the EV kit for this bundle. Note: This parameter is displayed only if PSN Type is set to MPLS. 0–255 Default: 128 Number of VLAN Tags [0 - 2] Defines if VLAN tagging is enabled and how many VLAN tags are used. 0: No VLAN Tag 1: One VLAN tag 2: Two VLAN tags (stacked) Default: 0 VLAN Protocol Defines the tag protocol identifier (TPID) to use when using VLAN tags. Note: This parameter is displayed only if Number of VLAN tags is set to 1 or 2. Standard (0x8100) Proprietary Default: Standard (0x8100) VLAN ID 1 VLAN identifier, uniquely identifying the VLAN to which the Ethernet packet belongs. Note: This parameter is displayed only if Number of VLAN tags is set to 1 or 2. 1–4095 Default: 1 VLAN ID 2 VLAN identifier, uniquely identifying the VLAN to which the Ethernet packet belongs. Note: This parameter is displayed only if the Number of VLAN tags is set to 2. 1–4095 Default: 1 VLAN 1 Priority Sets the priority of the packet in the virtual LAN. Note: This parameter is displayed only if the Number of VLAN tags is set to 1 or 2. 0–7 Default: 0 VLAN 2 Priority Sets the priority of the packet in the virtual LAN. Note: This parameter is displayed only if the Number of VLAN tags is set to 2. 0–7 Default: 0 Defines the header encapsulated in the packets leaving the EV kit. IP: UDP/IP header MPLS: MPLS header L2TPV3: L2TPV3/IP header Ethernet: MEF header Default: IP Sanity check between the received packet length and the length according to bundle configuration (length mismatch). CPU: Sends the packets that fail the sanity check to the CPU Discard: Drops the packets that fail the sanity check Default: Discard PSN Type Switches Sanity Check 44   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 Table 4-7. CESoPSN Bundle Parameter Descriptions (continued) PARAMETER DESCRIPTION POSSIBLE VALUES Clock Recovery Determines whether this bundle is used by the clock recovery mechanism. Yes: Bundle is used by clock recovery mechanism No: Bundle is not used by clock recovery mechanism Default: No Differential Time (usec) [1 - 512000] Desired depth of the jitter buffer. 1–512000μs Default: 5000 Max Buffer Size (usec) [1 - 512000] Defines the maximum size of the jitter buffer. When this parameter is set to zero, the maximum jitter buffer size equals (2 x PDVT) + (2 x packet fill time). 0–512000μs Default: 0 L Bit & OOS Defines how the OOS condition at the TDM interface is transmitted towards the Ethernet side. 1. OOS Mode Conditioning: OOS condition is reported by the OOS (ETH cond data) code and L-bit of the TDMoIP frame. 2. OOS Disable: OOS condition is not reported, but user data with L-bit keeps on being sent towards the Ethernet interface. 3. OOS Mode Tx Off: OOS condition is not reported and faulty user data is not transmitted towards the Ethernet interface. 4. OOS Mode Conditioning with JB reset: OOS condition is reported by the OOS (ETH cond data) code and L-bit of the TDMoIP frame. Reset jitter buffer when L-bit cleared. 5. OOS Disable with JB reset: OOS condition is not reported, but user data with L-bit keeps on being sent towards the Ethernet interface. Reset jitter buffer when L-bit cleared. 6. OOS Mode Tx Off with JB reset: OOS condition is not reported and faulty user data is not transmitted towards the Ethernet interface. Reset jitter buffer when L-bit cleared. Redundant Defines whether this bundle is a redundant bundle. Note: The bundle redundancy cannot be changed after the bundle configuration has been saved. Note: Redundant mode not supported Enable: Current bundle is redundant Disable: Current bundle is not redundant Default: Disable RTP Mode Determines if an RTP header is used for the bundle. Must be used for common clock mode. Enable: RTP header is used Disable: RTP header is not used Default: Disable Next Hop Type Must be set to MAC for next hops that do not reply to ARP requests. IP MAC Default: IP Maxim Integrated   45 DS34S132 Evaluation Kit Evaluates: DS34S132 Table 4-7. CESoPSN Bundle Parameter Descriptions (continued) PARAMETER DESCRIPTION POSSIBLE VALUES Enable JB Reset A mechanism that enables setting an optimum level for the jitter buffer working level. It enables the reset of a bundle until a satisfactory jitter buffer level is reached to minimize the delay. Off: Bundle reset is disabled and the working level of the jitter buffer is determined by the timing the bundle was first opened On N Times: Up to N times of bundle reset is allowed Endless: Bundle reset is allowed with unlimited number of resets Default: On N Times Window Size [2 - 127] The maximum number of conditioning Ethernet packets that can be inserted upon a loss of received Ethernet packets. If the difference in packet SN is greater than the configured window, there is no insertion of conditioning packets. 2–127 Default: 83 Number Of Outer Cookies Determines if L2TPV3 cookies are used and how many. Note: This parameter is displayed only when PSN Type = L2TPV3. 0: L2TPV3 cookies are not used 1: One L2TPV3 cookie is used 2: Two L2TPV3 cookies are used Default: 0 Cookie 1 Optional field that contains a randomly selected value used to validate association of the packet with the expected bundle identifier. Note: This parameter is displayed only when PSN Type = L2TPV3 and Number of Outer Cookies is 1 or 2. 0–4294967295 Default: 0 Cookie 2 Optional field that contains a randomly selected value used to validate association of the packet with the expected bundle identifier. Note: This parameter is displayed only when PSN Type = L2TPV3 and Number of Outer Cookies is 2. 0–4294967295 Default: 0 Number Of Outer Labels Determines if MPLS outer labels are used and how many. Note: This parameter is displayed only when PSN Type = MPLS. 0: MPLS outer labels not used 1: One MPLS outer label is used 2: Two MPLS outer labels are used Default: 0 MPLS Outer Label 1 MPLS Outer Label (only when not equal to 0) identifies the MPLS LSP which is used to tunnel the TDM packets through the MPLS network. Note: When equal to 0, only the Inner Label exists. Note: This parameter is displayed only when PSN Type = MPLS and Number of Outer Labels is 1 or 2. 0–1048575 Default: 0 MPLS Outer Label 2 MPLS Outer Label (only when not equal to 0) identifies the MPLS LSP which is used to tunnel the TDM packets through the MPLS network. Note: When equal to 0, only the Inner Label exists. Note: This parameter is displayed only when PSN Type = MPLS and Number of Outer Labels is 2. 0–1048575 Default: 0 Experimental Bits Sets the value of the MPLS experimental bits. Note: This parameter is displayed only when PSN Type = MPLS. 0–7 Default: 0 46   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 Table 4-7. CESoPSN Bundle Parameter Descriptions (continued) PARAMETER DESCRIPTION POSSIBLE VALUES Determines the bundle structure. Data: The bundle is configured as Structured (without CAS). Voice CAS: The bundle is configured as Structured with CAS. For units with T1 interface the payload type can be set to voice with CAS, if the interface type of the far-end unit is set to T1 SF or T1 ESF. Note: For redundant or cross-connect bundles, both bundles must be the same payload type. The payload type cannot be changed after the bundle configuration has been saved. Reordering Determines whether to reorder received misordered packets. Yes: Received misordered packets are reordered No: Received misordered packets are not reordered Default: Yes Number of Frames [1 - 1500] The number of TDM frames included in the CESoPSN payload. 1–1500 Default: 24 Condition octet used in the Ethernet direction when no data is available. Octet A Octet B Octet C Octet D Default: Octet A TDM Cond Octet Type Condition octet used in the TDM direction when no data is available. Octet A Octet B Octet C Octet D Default: Octet A RTP Source Identifier The RTP header Source Identifier value for transmitted packet. Note: This parameter is displayed only when RTP Mode is Enabled. 0–4294967295 Default: 111111111 RTP Payload The RTP header Payload value for transmitted packet. Note: This parameter is displayed only when RTP Mode is Enabled. 0–255 Default: 96 Note: This parameter is displayed only when Redundant is Enabled. None: Redundancy disabled (no bundles are transmitted) 1 and 1 1 plus 1 1 and 1 HW: Only one of the redundant bundles (primary or secondary) is transmitted 1 plus 1 HW: Both redundant bundles (primary and secondary) are transmitted Default: 1 plus 1 HW Payload Type Eth Cond Octet Type Redundant Type Maxim Integrated   47 DS34S132 Evaluation Kit Evaluates: DS34S132 Table 4-7. CESoPSN Bundle Parameter Descriptions (continued) PARAMETER Far End Interface Type TX Bundle Number Location at UDP Port RX Bundle Number Location at UDP Port DESCRIPTION POSSIBLE VALUES Type of the interface at the far end. T1: ESF or SF E1: Not applicable Default: ESF Indicating the location of the Transmitting Bundles UDP port. Source: UDP port number is at Source Port side Destination: UDP port number is at Destination Port side Indicating the location of the Receiving Bundles UDP port. Source: UDP port number is at Source Port side Destination: UDP port number is at Destination Port side To delete a bundle: To display a table of active bundles: 1) From the Main Configuration (S132) menu, select Bundle Management. 1) From the Main Configuration (S132) menu, select Bundle Management. 2) In the Bundle Management menu select Delete Existing Bundle(s). 2) In the Bundle Management menu select Display Existing Bundle(s). 3) Type in the bundle ID to be deleted and press Enter. 4.7 Restoring Default Configurations Once a bundle is deleted, the bundle ID in Bundle Configuration is deleted. Any assignments made to that bundle are deleted. To erase all configurations and restore factory-default configurations, select Restore Default Configurations from the Main Configuration (S132) menu. 4.6 Displaying Active Bundles 48   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 5. Troubleshooting and Diagnostics Users can troubleshoot the DS34S132 EV kit by viewing alarms, performance monitoring counters, or the troubleshooting chart. 5.1 Displaying Alarms The TopAlarms Menu displays the following types of alarms: • General Alarms • Interface Alarms • Bundle Alarms To view alarms select Alarms from the Main Configuration (S132) menu. The TopAlarms Menu appears as shown in Figure 5-1. 5.1.1 Displaying General Alarms To display general alarms, from the TopAlarms Menu (Figure 5-1) select General Alarms. The General Alarms menu appears (Figure 5-2). TopAlarms Menu 1. 2. 3. General Alarms Interface Alarms Bundle Alarms Please select item q: exit, s: save, ESC: previous menu, r or Enter: reprint screen Please enter your choice: Figure 5-1. TopAlarms Menu General Alarms 1. 2. 3. 4. 5. 6. 7. SW Tx TDM packet loss SW Rx LAN Packet Loss Rx FIFO Size Rx Ip Ver Err Status Rx Fifo Sof Err Rx MPLS Err MAC Receive Fifo Overrun OFF OFF 28 OFF OFF OFF OFF n: next screen, p: previous screen, ESC: previous menu q: exit, r: manually update, c: reset d: disable automatically update, e: enable automatically update Please enter your choice: Figure 5-2. General Alarms Menu Table 5-1. General Alarms Parameter Descriptions PARAMETER DESCRIPTION POSSIBLE VALUES SW Tx TDM packet loss Packets received from TDM to CPU were discarded due to lack of buffers in the TDMoP IC. ON, OFF SW Rx LAN packet loss Packets received from LAN to CPU were discarded due to lack of buffers in the TDMoP IC. ON, OFF Rx FIFO Size Indicates the current Rx FIFO level given in dwords (32 bits) 0–3FF Rx Ip Ver Err Status Received packet IP version does not match the configured IP version. ON, OFF Rx Fifo Sof Err Start of packet indication mismatch in Rx FIFO (indicates a bundle configuration error). Results in flushing the Rx FIFO’s contents. ON, OFF Rx MPLS Err MPLS packet received with more than three labels (packet is discarded). ON, OFF MAC Receive Fifo Overrun MAC receive FIFO has overflowed. ON, OFF Maxim Integrated   49 DS34S132 Evaluation Kit Evaluates: DS34S132 5.1.2 Displaying Interface Alarms 2) Enter the TDM link (port) number. To display E1/T1 interface alarms: 3) From the Interface Alarm menu, select TDM Alarms. The TDM Alarms menu is displayed (Figure 5-3). 1) From the TopAlarms Menu (Figure 5-1) select Interface Alarms. E1 TDM Alarms for Port 1 1. 2. 3. 4. 5. 6. 7. Loss of Signal Loss of Frame AIS RAI RX FRAME SLIP TX FRAME SLIP BPV/CV ERRORs ON ON OFF OFF OFF OFF 0 n: next screen, p: previous screen, ESC: previous menu q: exit, r: manually update, c: reset d: disable automatically update, e: enable automatically update Please enter your choice: Figure 5-3. TDM Alarms Menu Table 5-2. TDM Alarms Descriptions MESSAGE Loss of Signal DESCRIPTION POSSIBLE VALUES Loss of receive signal. Also indicated by the front panel SYNC LOS LED being lit. ON, OFF Check cable connection to the E1 link connector. Check line and/or other communication equipment connected to the link of the remote unit. CORRECTIVE ACTIONS Loss of Frame Loss of frame synchronization. ON, OFF Check the remote equipment. Perform the following: Check cable connection to the E1 connector of the remote device. Check line and/or other communication equipment providing the E1 link to the remote equipment. Replace the remote equipment. AIS AIS is detected on the link. ON, OFF Check equipment connected to the remote end of the E1 link. RAI RAI is detected on the link. ON, OFF Check equipment connected to the remote end of the E1 link. RX FRAME SLIP, TX FRAME SLIP E1 frame slips are detected (not displayed during local loss of frame synchronization). Updated once per second. ON, OFF Verify the clock settings. Check the far end (unstable clock source). Replace the EV kit only if previous steps do not correct the problem. BPV/CV ERRORs Bipolar violations or code violations on the link receive signal. Updated once per second. 0, 1, . . . Check the TDM equipment and cable connecting it to the E1 port. Replace the EV kit. 50   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 To display adaptive alarms: 5.1.3 Displaying Bundle Alarms 1) From the TopAlarms Menu (Figure 5-1), select Interface Alarms. The EV kit displays various per-bundle alarms. To display bundle alarms: 2) Enter the TDM link (port) number. 1) From the TopAlarms Menu (Figure 5-1), select Bundle Alarms. 3) From the Interface Alarms menu, select Adaptive Alarms. The Adaptive Alarms menu is displayed (Figure 5-4). If a problem cannot be corrected by carrying out the actions listed in Table 5-2 or Table 5-3, perform the actions corresponding to the problem symptoms in accordance with Table 5-4. 2) Enter the bundle ID. Depending on the bundle type, one of the alarm menus shown in Figure 5-5 is displayed. Adaptive Alarms for Port 1 1. 2. 3. Current State System Freeze DSP state (Debug use only) Tracking 2 OFF Locked n: next screen, p: previous screen, ESC: previous menu q: exit, r: manually update, c: reset d: disable automatically update, e: enable automatically update Please enter your choice: Figure 5-4. Adaptive Alarms Menu Table 5-3. Adaptive Alarms Descriptions MESSAGE DESCRIPTION POSSIBLE VALUES Current State Current state of the clock recovery mechanism. No recovery: Clock recovery mechanism is disabled. Idle: Clock recovery mechanism is in its idle state Acquisition: Frequency acquisition state. Tracking 1, Tracking 2: In these phases, the clock recovery mechanism performs slow and precise phase tracking. Verify that the bundle is configured as clock recovery enabled, and that the link clock is configured to be recovered. System Freeze The DPLL input level was frozen. ON, OFF — DSP state (Debug use only) Debugging tool for designers. Free Running with Calibration Locked Unlocked — Maxim Integrated CORRECTIVE ACTIONS   51 DS34S132 Evaluation Kit Evaluates: DS34S132 5.1.3.1 SAToP/CES Bundle Alarms See Figure 5-5 and Table 5-4 for the SAToP/CES bundle alarm options. CES Alarms Screen for Bundle 5 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Tx Frame with R bit (No Rx Packets) Tx Frame with L bit (TDM Interface Fail) Tx Frame with M bits HW lack of Tx buffers Rx TDMoIP Length Mismatch Rx Frame with R bit (Remote Fail) Rx Frame with L bit (Remote TDM Fail) Rx Frame with M bits Overrun Occurred Underrun Occurred JB Reset Occurred RX Fragmentation Bit Frame Count Err Jump Overflow Err Sequence Number Drop Err Miss Ordered Discard OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF n: next screen, p: previous screen, ESC: previous menu q: exit, r: manually update, c: reset d: disable automatically update, e: enable automatically update Please enter your choice: Figure 5-5. SAToP/CES Bundle Alarms Menu Table 5-4. SAToP or CES Bundle Alarm Descriptions PARAMETER DESCRIPTION POSSIBLE VALUES Tx Frame with R bit (No Rx Packets) Transmit packets with Remote Fail indication (R-bit) set. ON, OFF Tx Frame with L bit (TDM Interface Fail) Transmit packets with Local Fail indication (L-bit) set. ON, OFF Tx Frame with M bits Transmit packets with Modifier bits (M-bits) set. ON, OFF HW lack of Tx buffers Packet received from TDM was discarded due to lack of buffers associated with this bundle. ON, OFF Rx TDMoIP Length Mismatch The length of an incoming packet did not match the length expected for the bundle configuration. ON, OFF Rx Frame with R bit (Remote Fail) Received packets with Remote Fail indication (R-bit) set. ON, OFF Rx Frame with L bit (Remote TDM Fail) Received packets with Local Fail indication (L-bit) set. ON, OFF Rx Frame with M bits Received packets with Modifier bits (M-bits) set. ON, OFF Overrun Occurred Overrun has occurred in jitter buffer. ON, OFF Underrun Occurred Underrun has occurred in jitter buffer. ON, OFF JB Reset Occurred The jitter buffer was reset. ON, OFF Packet fragmentation status. ON: Packet is fragmented OFF: Entire (unfragmented) multiframe structure is carried in a single packet RX Fragmentation Bit 52   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 Table 5-4. SAToP or CES Bundle Alarm Descriptions (continued) PARAMETER DESCRIPTION POSSIBLE VALUES Start frame or multiframe insertion (CES bundles only) Start frame or multiframe mismatch. ON, OFF Frame Count Err Packets that belong to structured with CAS bundles were received with incorrect number of frames. ON, OFF Jump Overflow Err Packets received with incorrect sequence number (higher than the expected sequence number and within the window allowed by the configured Rx_max_lost_packets value) and could not be inserted into the jitter buffer due to insufficient space. ON, OFF Sequence Number Drop Err Packets discarded due to incorrect sequence number (SN equal to the former or gap between them exceeds limit determined by ‘Rx_max_lost_packets’ parameter). ON, OFF Miss Ordered Discard Packets discarded because they were considered duplicated, or because they were received too late to be inserted into the jitter buffer. ON, OFF 5.2 Displaying Performance Monitoring Counters The EV kit provides statistics collection for the Ethernet interface and bundles. 5.2.1 Displaying Ethernet Counters 2) Select Ethernet Performance. The Ethernet Performance Data menu is displayed (Figure 5-7). This menu is automatically redisplayed every few seconds. To disable automatic updates, select d from the menu. To reset the Ethernet performance monitoring counters, select c. To display the Ethernet counters: 1) From the Main Configuration (S132) menu (Figure 3-2), select Performance (PM). The TopPMs Menu (performance monitoring) is displayed (Figure 5-6). TopPMs Menu 1. 2. 3. Ethernet Performance Interface Performance Bundle Performance Please select item q: exit, s: save, ESC: previous menu, r or Enter: reprint screen Please enter your choice: Figure 5-6. Performance Monitoring Menu Maxim Integrated   53 DS34S132 Evaluation Kit Evaluates: DS34S132 Ethernet Performance Data 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Correct Bytes (RX) Correct Frames (RX) Pause Packets (RX) FCS Error Alignment Errors Symbol Errors Excessive Length Ers Jabbers Errors Under size Packets Classified Packets Checksum Err Packets Stray Packets 0 0 0 0 0 0 0 0 0 0 0 0 Correct Bytes (TX) Correct Frames (TX) Pause Packets (TX) Single Collision Multiple Collision Deferred Frames Underrun Excessive Collision Late Collision Carrier Sense Sqe Test Errors 0 0 0 0 0 0 0 0 0 0 0 n: next screen, p: previous screen, ESC: previous menu q: exit, r: manually update, c: reset d: disable automatically update, e: enable automatically update Figure 5-7. Ethernet Performance Data Menu Table 5-5. Ethernet Performance Data Descriptions PARAMETER DESCRIPTION POSSIBLE VALUES Correct Bytes (RX) The number of ETH packet octets successfully received (not including CRC). When a valid connection is established the number increases steadily. This counter wraps around to 0 after reaching the maximum value. 32-bit number Correct Frames (RX) The number of ETH packets successfully received. When a valid connection is established the number increases steadily. This counter wraps around to 0 after reaching the maximum value. 32-bit number Pause Packets (RX) The number of good ETH pause packets received. A good packet has a length of 64 to 1518 (1536 if bit 8 is set in the network configuration register) and has no FCS, alignment, or receive symbol errors. 0–511 FCS Error Counts the number of packets received that do not pass the FCS check (RFC 1643). An FCS check is a mathematical way to ensure that all the frame bits are correct without the system having to examine each bit and compare it against the original. Recommendation: Check for physical problem such as hardware problem, or a bad line, or noisy environment. Alignment Errors The number of packets received that are not an integral number of octets in length (RFC 1643). All frames should end on an 8-bit boundary, but physical problems on the network could cause the number of bits to deviate from the multiple of eight. Recommendation: Check physical connections, devices and configuration. 0–255 Symbol Errors The number of packets from PHY that had Rx_err during reception. 0–255 Excessive Length Ers The number of received packets where the length exceeds 1518 bytes, and without CRC error, alignment error or symbol error. 0–255 Jabbers Error The number of received packets exceeding 1518 bytes (1536 if bit 8 set in network configuration register) in length and have either a CRC error, an alignment error or a receive symbol error. 0–255 Under size Packets The number of received packets where the length is less than 64 bytes, without CRC error or alignment error. 0–255 54   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 Table 5-5. Ethernet Performance Data Descriptions (continued) PARAMETER DESCRIPTION POSSIBLE VALUES Classified Packets The number of packets that passed packet classifier. Checksum Err Packets The number of packets with IP checksum errors. Stray Packets The number of strayed packets. Correct Bytes (TX) The number of octets successfully transmitted (not including CRC). When a valid connection is established the number increases steadily. Correct Frames (TX) The number of packets successfully transmitted. When a valid connection is established the number increases steadily. Pause Packets (TX) The number of pause packets transmitted. Single Collision Counter of successfully transmitted packets for which transmission is inhibited by exactly one collision. Recommendation: Use a full-duplex mode if possible. Valid only in half-duplex mode (RFC 1643) Multiple Collision Counter of successfully transmitted packets for which transmission is inhibited by 2 to 15 collisions. Recommendation: Use a full-duplex mode if possible. Valid only in half-duplex mode (RFC 1643) Deferred Frames The number of packets experiencing deferral due to carrier sense being active on the first attempt at transmission. Packets involved in any collision are not counted nor are packets that experienced a transmit underrun. 0–511 Underrun The number of packets that were not transmitted due to transmit FIFO underrun. Excessive Collision The number of packets that were not transmitted due to 16 collisions. 0–255 Late Collision To allow collision detection to work properly, the period in which collisions are detected is restricted (512 bit-times). For 10BASE-T Ethernet (10Mbps), it is 51.2Fs; for Fast Ethernet (100Mbps) it is 5.12Fs. For Ethernet stations, collisions can be detected up to 51.2 Fs after the beginning of the transmission, or in other words, up to the 512th bit of the frame. When a station detects a collision after it has sent the 512th bit of its frame, this is counted as a late collision. Note: A late collision is counted twice—as a collision and as a late collision. Recommendation: Check if there is incorrect cabling or a non-compliant number of hubs in the network. Bad network interface cards (NICs) can also cause late collisions. Valid only in half-duplex mode (RFC 1643) 0–255 Carrier Sense The number of packets transmitted where carrier sense was not seen during transmission or where it was deasserted after being asserted in the transmit packet without collision. Recommendation: Check connection between the UPLINK interface and its Ethernet transceiver. Valid only in half-duplex mode (RFC 1643) 0–255 Sqe Tst Errors The number of packets where COL was not asserted within 96 bit-times (an interpacket gap) of TX_EN being deasserted in half-duplex mode. 0–255 Maxim Integrated 32-bit number   55 DS34S132 Evaluation Kit Evaluates: DS34S132 5.2.2 Displaying Bundle Counters The EV kit displays counters for HDLC, SAToP, and CES bundles. To display bundle counters: 1) From the Main Configuration (S132) menu (Figure 3-2), select Performance (PM). 2) The TopPMs Menu (performance monitoring) is displayed (Figure 5-6). Select Bundle Performance. 3) A list of open bundles is displayed. Enter the ID number of the bundle for which you want to display the performance monitoring counters. The Bundle PMs menu is displayed (SAToP/CESoPSN: Figure 5-8). This menu is automatically redisplayed every few seconds. To disable automatic updates, select d from the menu. To reset the Ethernet performance monitoring counters, select c. 5.2.2.1 Displaying SAToP/CES Bundle Counters See Figure 5-8 and Table 5-6 for SAToP/CES bundle counter options. SATOP Bundle PMs for Bundle 5 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Correct Frames Tx to LAN Correct Frames Rx from LAN Lost Frames in Rx Minimum JB Level [Usec] Maximum JB Level [Usec] Discarded Packets in Rx Reordered Packets in Rx Underrun Occurred Jump Packets in Rx MisOrdered Packets in Rx Rx MalFormed Packets Rx R-bit Packets Tx L-bit Packets Overrun Occurred Loss of Frames Occurred 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 n: next screen, p: previous screen, ESC: previous menu q: exit, r: manually update, c: reset d: disable automatically update, e: enable automatically update Figure 5-8. SAToP/CES Bundle Counter Menu Table 5-6. SAToP/CES Bundle Counter Descriptions PARAMETER DESCRIPTION Correct Frames Tx to LAN The number of packets successfully transmitted for the bundle. When a valid connection is established, the number increases steadily. Correct Frames Rx from LAN The number of packets successfully received for a bundle. When a valid connection is established, the number increases steadily. Lost Frames in Rx There are two possible reasons for lost frames: Packet or packets are dropped or lost somewhere along the network. Reordering of packets by network. Packet reordering can occur due to queuing mechanisms, rerouting by the network, or when the router updates very large routing tables and is therefore overloaded. Recommendations: Ensure the EV kit traffic has sufficient bandwidth. Ensure the Ethernet connection is functioning properly. Ensure the Ethernet/IP network provides priority (quality of service) to the EV kit traffic. Priority can be achieved by two means: VLAN tagging and IP ToS marking. Verify that the IP network devices (switches/routers/modems/etc.) can handle the EV kit PPS (packets per second) rate. Ensure the network devices do not drop/lose/ignore packets by checking their statistics. Minimum JB Level [Usec] The minimum jitter buffer level for the current bundle. 56   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 Table 5-6. SAToP/CES Bundle Counter Descriptions (continued) PARAMETER DESCRIPTION Maximum JB Level [Usec] The maximum jitter buffer level for the current bundle. Discarded Packets in Rx Number of received packets that were discarded by SAToP/CESoPSN payload type machine. Reordered Packets in Rx Number of received misordered packets that were successfully reordered by SAToP/ CESoPSN payload type machine. Underrun Occurred An underrun situation can be caused by: Buffer starvation: Packets delay variation causes the buffer to empty out gradually until it underflows. Continuous sequence errors: The sequence error means a halt in the valid stream of packet arrival into the jitter buffer. Packets are stopped/lost/dropped. Differential timing (PDVT) configuration that is not large enough to compensate for the network delay variation. In a TDM network, all system elements must be locked to one master clock. If not, it leads to a situation in which data is clocked out of the jitter buffer at a rate different from the one that is clocked in. This gradually results in either an overflow or underflow event, depending on which rate is higher. The event repeats itself periodically as long as the system clock is not locked. Recommendations: Try increasing the differential timing (PDVT) in a bundle configuration. Check reasons for sequence errors or lost/dropped packets (if present), system clocking configuration, Ethernet environment (full duplex), and connection, packets drop/loss/ignore by routers/switches or nonuniform packets output by routers/switches due to queuing mechanisms. Ensure the same number of time slots for bundle is configured on each end. Ensure the Ethernet/IP network provides priority (quality of service) to the TDMoP traffic. Priority can be achieved by two means: VLAN tagging and IP TOS marking. Jump Packets in Rx Number of jumped packets encountered by SAToP/CESoPSN payload type machine. System software can calculate the number of lost packets using the following equation: Lost Packets = (Jumped Packets - Reordered Packets). MisOrdered Packets in Rx Received misordered packets. Rx MalFormed Packets Received malformed packets. Rx R-bit Packets Received packets with R-bits. Tx L-bit Packets Transmitted packets with L-bits. Overrun Occurred Number of overrun occurred. Loss of Frames Occurred Total loss of frames occurred. Maxim Integrated   57 DS34S132 Evaluation Kit Evaluates: DS34S132 5.2.3 Displaying TDM Interface Counters 5.3.3 Set Debug Flags This is not yet implemented in the DS34S132 EV kit user interface software. This option is for debug purposes only. Maxim Technical Support provides support for this function. 5.3 Utility Menu 5.4.4 Management Network Information 5.3.1 Read Memory/Write Memory This option displays the Ethernet management port information. It displays the MAC address, IP address, and other network information. For advanced troubleshooting, the system software has menu options to read and write the registers of the DS34S132 and other peripherals. From the Main Configuration (S132) menu, select either Read Memory or Write Memory and follow the prompts. These selections (options 1 and 2) can access the DS34S132 registers, but not DSP memory or DDR memory. To access DSP or DDR memory, the user must use options 11–14. 5.3.2 Update ToP Application This option allows the user to upgrade the Linux-based software package to the newest version, if necessary. Table 5-7. DS32S132 EV Kit Address Map ADDRESS DEVICE 0xF0000000 DS34S132 0xF0020000 DS26518 #1 0xF0030000 DS26518 #2 0xF0040000 DS26518 #3 0xF0050000 DS26518 #4 0xF0060000 DS3100 0xF0070000 CPLD 0xF0080000 Motherboard FPGA 5.3.5 Loopbacks The DS34S132 EV kit supports local and remote loopbacks that can be run on the physical interfaces and bundles. The loopbacks can be used to check internal circuitry of the unit and its physical network and bundle connections. Options 1–4 refer to loopbacks on the T1/ E1 transceivers. Refer to the DS26518 IC data sheet for more information. 5.3.5.1 Enabling Loopbacks To run a loopback on a physical port: 1) From the Main Configuration (S132) menu, select Utilities. 2) The Utility menu is displayed. 3) From the Utility menu, select Loopbacks. 4) Specify the TDM interface number. 5) The Loopbacks Menu is displayed (Figure 5-9). 6) Select Remote Loopback, Local Loopback, or any of several other loopback types. 7) Select Enable. Loopbacks Menu 1. 2. 3. 4. 5. 6. Remote Loopback Payload Loopback Framer Loopback Local Loopback Ethernet Loopback PHY Loopback Disable Disable Disable Disable Unknown Unknown Please select item q: exit, s: save, ESC: previous menu, r or Enter: reprint screen Please enter your choice: Figure 5-9. Loopbacks Menu 58   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 5.3.5.2 Framer Loopback and Payload Loopback 5.3.5.4 Remote Loopback These loopbacks are not necessary for troubleshooting purposes. Remote and local loopbacks are sufficient. Refer to the DS26518 IC data sheet for more information on the use of these loopbacks. Remote loopback returns the data received on the TDM receive port to the test equipment connected to the TDM transmit port. See Figure 5-11. 5.3.5.3 Local Loopback The Ethernet loopback loops data at the transmit MAC interface (internal on the DS34S132) to the receive MAC interface. Data coming from the TDM side is looped back to the TDM interface. See Figure 5-12. Local loopback returns packets received through the IP interface towards the network. Figure 5-10 shows the signal path for a typical local loopback. T1/E1 TRANSCEIVER TDMoP 5.3.5.5 Ethernet Loopback ETH PHY PACKET SWITCHED NETWORK TESTING EQUIPMENT DS34S132 EV KIT TDM INTERFACE IP INTERFACE Figure 5-10. Local Loopback Diagram T1/E1 TRANSCEIVER TESTING EQUIPMENT TDMoP ETH PHY DS34S132 EV KIT TDM INTERFACE IP INTERFACE Figure 5-11. Remote Loopback Diagram T1/E1 TRANSCEIVER TESTING EQUIPMENT TDMoP ETH PHY DS34S132 EV KIT TDM INTERFACE IP INTERFACE Figure 5-12. Ethernet Loopback Diagram Maxim Integrated   59 DS34S132 Evaluation Kit Evaluates: DS34S132 T1/E1 TRANSCEIVER TESTING EQUIPMENT TDMoP ETH PHY DS34S132 EV KIT TDM INTERFACE IP INTERFACE Figure 5-13. PHY Loopback Diagram 5.3.5.6 PHY Loopback The PHY loopback loops data at the Ethernet PHY received from the TDM interface (through the DS34S132) back to the TDM interface. See Figure 5-13. 5.3.6 Reboot System 5.3.10 Read S132 Memory/Write S132 Memory (DDR Memory) Access to the DS34S132 memory and DDR SDRAM. 5.3.11 Read DSP Memory/Write DSP Memory Reboots the whole EV kit (hardware and software reboot). Access to DSP embedded in the DS34S132 for clock recovery. No offset required. Debugging use only. 5.3.7 UART Baud Rate 5.3.12 System Information Allows the user to change to change the serial-port baud rate (default 115200bps). Describes SW Version, S132 revision, HAL (driver) revision, and DSP Version (embedded in the DS34S132). 5.3.8 Read Script Configuration File from Terminal 5.3.13 Execute Linux Command This option is not functional at this time. This option allows the user to execute a Linux command without exiting the EV kit software program. 5.3.9 Send OAM Packet to Other Party 5.4 Troubleshooting Chart This option is not functional at this time. Table 5-8 lists possible faults, probable causes, and the actions necessary to correct the situation. 60   Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 Table 5-8. Troubleshooting Chart FAULT The E1/T1 equipment connected to EV kit is not synchronized (E1/T1 level) with the EV kit. Slips and errors in E1/T1 equipment. Echo in voice. Ethernet interface LINK indicator is not lit. Maxim Integrated PROBABLE CAUSE CORRECTIVE ACTIONS Configuration problems Check the EV kit port configuration. — Check E1/T1 alarms to indicate the exact cause. Ethernet port is set to work in half-duplex mode (can cause extreme PDV because of collisions and back-offs). Ethernet ports of the local and remote devices are not set to the auto negotiation mode or set to different rates. Check the EV kit port configuration (autonegotiation, rate, duplex mode) and check Ethernet PM. Timing configuration is not properly set (periodic buffer under/overflows—bundle connection status menu). Check the timing settings. Network PDV or lost frames Check PDV introduced by the network, and, if necessary, increase differential time (PDVT) setting. End-to-end delay is too large Check network delay and try to decrease it. Try to decrease differential time (PDVT). Decrease Ethernet packet size by changing bundle configuration. No active station on the LAN Check that at least one station is active on the LAN. Cable problem Check and replace, if necessary, the cable that connects the EV kit UPLINK connector to the LAN. Problem on the LAN Check LAN media. Defective EV kit Replace the EV kit if a failure is detected.   61 DS34S132 Evaluation Kit Evaluates: DS34S132 Appendix A. Connector Wiring A.3 ASCII Terminal Connector A.1 E1/T1 and External Clock Connectors The control terminal interface terminates in a V.24/ RS-232, 9-pin, D-type female DCE connector, wired in accordance with Table A-3. The E1/T1 and external clock interfaces of the DS34S132 EV kit terminate in 8-pin RJ45 connectors, wired in accordance with Table A-1. A.2 Ethernet Connectors The Ethernet uplink and Ethernet management electrical interfaces terminate in 8-pin RJ45 connectors, wired in accordance with Table A-2. Table A-1. E1/T1 and External Clock Interface Connector Pinout PIN DESIGNATION DIRECTION FUNCTION 1 RD (R) Input Receive data (ring) 2 RD (T) Input Receive data (tip) 3, 6 — — FGND 4 TD (R) Output Transmit data (ring) 5 TD (T) Output Transmit data (tip) 7, 8 — N/A Not connected Table A-2. Ethernet Connector Pinout 62   Table A-3. Control Interface Pinout PIN FUNCTION PIN FUNCTION 1 Tx+ 1 – 2 Tx- 2 Tx 3 Rx+ 3 Rx 6 Rx- 4 — 4, 5, 7, 8 — 5 GND 6, 7, 8 — Maxim Integrated DS34S132 Evaluation Kit Evaluates: DS34S132 Revision History REVISION NUMBER REVISION DATE 0 5/11 DESCRIPTION Initial release PAGES CHANGED — Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 ©  2011 Maxim Integrated Products, Inc. 63 Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.