ICL7135CAI

41/2 Digit A/D Converter with Multiplexed BCD Outputs ICL7135 General Description The Maxim ICL7135 is a high precision monolithic 41/2 digit A/D converter. Dual slope conversion reliability is combined with ±1 in 20,000 count accuracy and a 2.0000V full scale capability. It features high impedance differential inputs, nearly ideal differential linearity, true ratiometric operation, auto zero and auto-polarity. The multiplexed BCD outputs and digit drivers provide easy interface to external display drivers like the Maxim ICM7211A. The only other external components needed to make precision DVM/DPMs are a reference and a clock. For more complex systems the BCD outputs are enhanced by STROBE, OVERRANGE, UNDERRANGE, RUN/HOLD and BUSY lines providing easy interface to microprocessors and UARTs. This interfacing capability makes the ICL7135 an ideal device for use in microprocessor based data acquisition and control systems. The ICL7135 has auto-zero accuracy better than 10µV, zero drift of 0.5µV/°C, input bias current of 10pA max. and rollover error of less than 1 count. Applications This device is used in a wide range of measurement applications involving the manipulation and display of analog data: ●● Pressure ●● Weight ●● Voltage ●● Current ●● Resistance ●● Speed ●● Temperature ●● Material Thickness Pin Configuration Benefits and Features ●● Improved 2nd Source (See our “Maxim Advantage™” Page 3) ●● ±20,000 Count Resolution ●● Guaranteed ±1 Count accuracy ●● Over-range, under-range signals for auto-range capability ●● Easy interface to UARTs and µPs ●● TTL compatible, Multiplexed BCD outputs ●● True differential input. Zero reading guaranteed for 0 volt Input ●● True polarity at zero for precise null detection ●● Monolithic CMOS Design Ordering Information PART TEMP. RANGE PIN-PACKAGE ICL7135CJI 0°C to 70°C 28 Lead CERDIP ICL7135CPI 0°C to 70°C 28 Lead Plastic DIP ICL7135CQI 0°C to 70°C 28 Lead Plastic chip carrier ICL7135C/D 0°C to 70°C Dice Typical Operating Circuit V- 1 28 UNDERRANGE REFERENCE 2 27 OVERRANGE ANALOG COMMON 3 26 STROBE INT OUT 4 25 AZ IN 5 ICL7135 24 BUFF OUT 6 23 POL REF. CAP- 7 22 CLOCK IN REF. CAP+ 8 21 BUSY IN LO 9 20 (LSD) D1 IN HI 10 19 D2 R/H DIGITAL GND V+ 11 18 D3 (MSD) D5 12 17 D4 (LSB) B1 13 16 (MSB) B8 B2 14 15 B4 NOTE: ALL PACKAGES HAVE THE SAME PINOUT. OR D1 D1 D2 BRT 28 SEGMENT DRIVERS D2 D3 D3 ICL7135 D4 D5 D4 ICM7212 STROBE B8 B4 B2 B1 POL LED DISPLAY B3 B2 B1 B0 D Q D Q The “’Maxim Advantage’” signifies an upgraded quality level. At no additional cost we offer a second-source device that is subject to the following: guaranteed performance over temperature along with tighter test specifications on many key parameters; and device enhancements, when needed, that result in improved performance without changing the functionality. 19-5041; Rev 1; 9/16 41/2 Digit A/D Converter with Multiplexed BCD Outputs ICL7135 Absolute Maximum Ratings Lead Temperature (Soldering, 10 sec)............................... 300°C Supply Voltage V+ .................................................................+6V V-.................................................................. -9V Analog Input Voltage (either input) (Note 1)................... V+ to VReference Input Voltage (either input) ........................... V+ to VClock Input...................................................................Gnd to V+ Note 1: Input voltages may exceed the supply voltages provided the input current is limited to +100µA. Note 2: Dissipation rating assumes device is mounted with all leads soldered to printed circuit board. Power Dissipation (Note 2) CERDIP Package ......................................................1000mW Plastic Package............................................................800mW Operating Temperature...........................................0°C to +70°C Storage Temperature ....................................... -65°C to + 160°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ICL7135 Electrical Characteristics (Note 1) (V+ = +5V, V- = -5V, TA = 25°C, Clock Frequency Set for 3 Reading/Sec) CHARACTERISTICS ANALOG (Note 1) (Note 2) SYMBOL MIN TYP MAX UNITS Zero Input Reading VIN = 0.0V Full Scale = 2.000V CONDITIONS -0.0000 ±0.0000 +0.0000 Digital Reading Ratiometric Reading (Note 2) VIN = VREF Full Scale = 2.000V +0.9995 +0.9999 +1.0000 Digital Reading Linearity over ± Full Scale (Error of Reading from Best Straight Line) -2V ≤ VIN ≤ +2V 0.5 1 Digital Count Error Differential Linearity (Difference Between WorstCase Step of Adjacent Counts and Ideal Step) -2V ≤ VIN ≤ +2V .01 Rollover error (Difference in Reading for Equal Positive and Negative Voltage Near Full Scale) -VIN ≡ VIN ≈ 2V 0.5 VIN = 0V Full Scale = 2.000V 15 Leakage Current at Input IILK VIN = 0V 1 10 pA 0.5 2 µV/°C 2 5 ppm/°C VIN = 0V 0° ≤ TA ≤ +70°C TC VIN = +2V 0° ≤ TA ≤ +70°C (ext. ref. 0 ppm/°C) VINH DIGITAL SUPPLY Clock In, Run/Hold Note Note Note Note 2.8 VINL µV 2.2 V 1.6 0.8 IINL VIN = 0V 0.02 0.1 mA IINH VIN = +5V 0.1 10 µA All Outputs VOL IOL = 1.6mA 0.25 0.40 V B1, B2, B4, B8 D1, D2, D3, D4, D5 VOH IOH = -1mA 2.4 4.2 V BUSY, STROBE, OVER-RANGE, UNDER-RANGE, POLARITY VOH IOH = -10µA 4.9 4.99 V +5V Supply Range V+ +4 +5 +6 V -5V Supply Range V- -3 -5 -8 V +5V Supply Current I+ fC = 0 1.1 3.0 -5V Supply Current I- fC = 0 0.8 3.0 Power Dissipation Capacitance Clock Digital Count Error en Scale Factor Temperature Coefficient (Note 3) OUTPUTS 1 Noise (P-P Value Not Exceeded 95% of Time) Zero Reading Drift INPUTS LSB Clock Frequency (Note 4) CPD vs. Clock Freq 40 DC 2000 mA pF 1200 kHz 1: Tested in 41/2 digit (20,000 count) circuit shown in Figure 1, clock frequency 120kHz. 2: Tested with a low dielectric absorption integrating capacitor. See Component Selection Section. 3: The temperature range can be extended to +70°C and beyond as long as the auto-zero and reference capacitors are increased to absorb the higher leakage of the ICL7135. 4: This specification relates to the clock frequency range over which the ICL7135 will correctly perform its various functions. See “Max Clock Frequency” below for limitations on the clock frequency range in a system. The electrical characteristics above are a reproduction of a portion of lntersil’s copyrighted (1983/1984) data book. This information does not constitute any representation by Maxim that Intersil’s products will perform in accordance with these specifications. The “Electrical Characteristics Table” along with the descriptive excerpts from the original manufacturer’s data sheet have been included in this data sheet solely for comparative purposes. www.maximintegrated.com Maxim Integrated │  2 41/2 Digit A/D Converter with Multiplexed BCD Outputs ICL7135 ●● Guaranteed 2mA Max Supply Current ●● Significantly Improved ESD Protection (Note 6) ●● Key Parameters Guaranteed Over Temperature ●● Low Noise ●● Maxim Quality and Reliability Absolute Maximum Ratings: This device conforms to the Absolute Maximum Ratings on adjacent page. Electrical Characteristics Specifications below satisfy or exceed all ‘’tested” parameters on adjacent page. (V+ = +5V, V- = -5V, TA = +25°C, Clock Frequency Set for 3 Reading/Sec) CHARACTERISTICS ANALOG (Note 1) (Note 2) SYMBOL DIGITAL SUPPLY MAX UNITS -0.0000 ±0.0000 -0.0000 Digital Reading Ratiometric Reading (Note 2) VIN = VREF, Full Scale = 2.000V TA = 25°C 0° ≤ TA ≤ +70°C +0.9998 +0.9999 +1.0000 +0.9995 +0.9999 +1.0005 Digital Reading 1 Linearity Over ± Full Scale (Error of Reading from Best Straight Line) -2V ≤ VIN ≤ +2V 0.5 Differential Linearity (Difference Between Worst-Case Step of Adjacent Counts and Ideal Step) -2V ≤ VIN ≤ +2V .01 -VIN = +VIN ≈ +2V 0.5 VIN = 0V, Full Scale = 2.000V 15 VIN = 0V TA = 25°C 1 VIN = 0V 0° ≤ TA ≤ +70°C Rollover Error (Difference in Reading for Equal Positive and Negative Voltage Near Full Scale) Noise (P-P value not exceeded 95% of time) en Leakage Current at Input IILK Clock In, Run/Hold TC VIN = +2V 0° ≤ TA ≤ +70°C Digital Count Error LSB 1 Digital Count Error µV 10 pA 250 pA µV/°C 0° ≤ TA ≤ +70°C 2 (ext. ref. 0ppm/°C) 2.8 5 VINH 0° ≤ TA ≤ +70°C VINL 0° ≤ TA ≤ +70°C 2.2 1.6 0.8 ppm/°C V IINL VIN = 0V 0° ≤ TA ≤ +70°C 0.02 0.1 mA IINH VIN = +5V 0° ≤ TA ≤ +70°C 0.1 10 µA 0.25 0.40 V All Outputs VOL IOL = 1.6mA B1, B2, B4, B8 D1, D2, D3, D4, D5 VOH IOH = -1mA 2.4 4.2 V BUSY, STROBE , OVER-RANGE, UNDER-RANGE POLARITY VOH IOH = -10µA 4.9 4.99 V +5V Supply Range V+ +4 +5 +6 -5V Supply Range V- -3 -5 -8 V fC = 0 TA = 25°C 0° ≤ TA ≤ +70°C 1.1 2.0 mA 3.0 mA fC = 0 TA = 25°C 0° ≤ TA ≤ +70°C 0.8 2.0 mA 3.0 mA 1200 kHz +5V Supply Current -5V Supply Current Power Dissipation Capacitance CLOCK TYP VIN = 0.0V, Full Scale = 2.000V 0° ≤ TA ≤ +70°C Scale Factor Temperature Coefficient (3) OUTPUTS MIN Zero Input Reading Zero Reading Drift INPUTS CONDITIONS Clock Frequency (Note 4) I+ ICPD (Note 5) 40 DC 2000 V pF Note 1: Tested in 41/2 digit (20,000 count) circuit shown in Figure 1, clock frequency 120kHz. Note 2: Tested with a low dielectric absorption integrating capacitor. See Component Selection Section. Note 3: The Temperature range can be extended to +70°C and beyond as long as the auto-zero and reference capacitors are increased to absorb the higher leakage of the ICL7135. Note 4: This specification relates to the clock frequency range over which the ICL7135 will correctly perform its various functions. See “Clock Frequency” below for limitations on the clock frequency range in a system. Note 5: +5V Supply current for fc ≠ 0 is I+ = I+ (fc = 0) + CPD x 5V x fc. Note 6: All pins are designed to withstand electrostatic discharge (ESD) levels in excess of 2000V. (Test circuit per MIL Std 883, Method 3015.1) www.maximintegrated.com Maxim Integrated │  3 41/2 Digit A/D Converter with Multiplexed BCD Outputs ICL7135 integrator capacitor at the end of signal integrate is directly proportional to the differential voltage between Input High and Input Low, and is also directly proportional to the length of the signal integrate phase. The signal integrate phase lasts precisely 10,000 clock cycles. At the end of this phase the input signal polarity is determined. SET VREF = 1.000V -5V VREF IN 1 V100kΩ UNDERRANGE 28 2 REFERENCE ANALOG GND 0.47µF 1.0µF 100kΩ OVERRANGE 27 3 ANALOG COMMON 27Ω STROBE 26 4 INT. OUT 5 A-Z IN RUN/HOLD 25 DIGITAL GND 24 OV De-Integrate Phase The ICL7135 is divided into an Analog section and a Digital section. The digital section includes the counters, input and output interfaces, and control logic which controls the timing of each measurement cycle. Each measurement is divided into four phases: 1) auto-zero (AZ), 2) signal integrate (INT), 3) reference deintegrate (DE), and 4) zero integrator (ZI). The digital section controls the operation of the analog section during each of these phases, using counters and the state of the comparator to determine when to start each of the four phases. At the end of signal integrate, Input High and Input Low are disconnected from the external pins. The integrator non-inverting input pin is then internally connected to Analog Common and the buffer input is connected to one side of the reference capacitor. The other side of the reference capacitor is connected to Analog Common. The polarity at the output of the integrator (as detected by the comparator at the end of signal integrate phase) determines which terminal of the reference capacitor is connected to the buffer input. The reference capacitor polarity is chosen so that the integrator output will always return towards Analog Common. Since the reference capacitor was charged to the reference voltage during the auto-zero phase, the integrator input voltage is now the reference voltage. The De-Integrate phase lasts for 20,001 counts, or until the comparator detects that the integrator output has crossed zero, whichever occurs first. The time required to return to zero is proportional to the input signal and is inversely proportional to the reference voltage. The number of clock cycles required to return to zero is counted by the digital section and is latched as the measurement result. VIN Displayed reading = 10,000 x VREF Auto-Zero Phase Zero Integrator Phase 6 BUFF OUT 100kΩ SIGNAL INPUT 100kΩ 1µF 0.1µF +5V 7 REF. CAP8 REF. CAP+ ICL7135 POLARITY 23 CLOCK IN 22 BUSY 21 9 IN LO LSD D1 20 10 IN HI D2 19 11 V+ D3 18 12 MSD D5 13 LSB B1 14 B2 CLOCK IN 120kHz D4 17 MSB B8 16 B4 15 Figure 1. ICL7135 Test Circuit Detailed Description General Operation During auto-zero Input HI and Input LO are disconnected from the input pins and are internally shorted to Analog COMMON. The output of the comparator is connected to the inverting input of the Integrator, and at the same time the non-inverting input of the integrator is connected to the input of the buffer. This feedback loop charges the autozero capacitor, CAZ, to compensate for the offset voltages of the buffer amplifier, integrator, and comparator. Also during auto-zero,the reference capacitor is connected to the voltage reference and is charged to the reference voltage. The auto-zero cycle is a minimum of 9800 clock cycles, except after an over-range reading. After an over-range, the extended zero integrate phase reduces the auto-zero phase to 3800 clock cycles. Signal Integrate Phase At the end of the auto-zero phase the auto-zero loop is opened, and the Input High and Input Low are switched to the external pins IN-HI and IN-LO. The analog section integrates the differential voltage between Input High and Input Low. The differential voltage must be within the ICL7135’s common mode range. The voltage on the www.maximintegrated.com The last of the four phases is the zero integrator phase. The non-inverting input of the integrator is internally shorted to Analog Common and the buffer input is internally connected to the output of the comparator. This closes a loop that forces the integrator output to zero. Normally this phase lasts only 100 to 200 counts, sufficient time to remove the small residual charge on the integrator capacitor caused by the comparator delay and the one count delay created by sampling the comparator output only once per clock cycle. However, an overrange condition will exist when the integrator output does not return to zero by the end of the De-Integrate phase, and can leave a residual voltage on the integrator capacitor. In this case, the Zero Integrator phase is increased to 6200 counts to ensure that the integrator capacitor is fully discharged before the next measurement cycle is started. Analog Section Analog COMMON Analog COMMON is the Analog ground reference for the ICL7135. If Input Low is at a voltage other than Analog Maxim Integrated │  4 41/2 Digit A/D Converter with Multiplexed BCD Outputs ICL7135 CREF CREF+ 8 V+ CAZ AUTO ZERO INT 11 5 4 RINT REF HI CREF 2 7 BUFFER 6 CINT INTEGRATOR INPUT HIGH A/Z IN HI 10 INT DE(-) DE(+) A/Z A/Z COMPARATOR ZI AZ ANALOG COMMON 3 IN LO 9 DE(+) INT INPUT LOW DE(-) A/Z + DE(±) + ZI ICL7135 1 V- Figure 2. Analog Section of ICL7135 COMMON a common mode voltage will be introduced and, although the ICL7135 has an excellent CMRR, Input Low and Analog COMMON should be connected together whenever possible. Analog COMMON is also the reference point for the reference voltage. The Analog Common voltage is normally connected to the system ground when using ±5V supplies. When the ICL7135 is operated from a single supply voltage the Analog Common should be connected to a voltage source approximately halfway between V+ and ground. Input Buffer The ICL7135 input buffer is a CMOS buffer with a common mode input voltage range of approximately V+ -1.0V to V- +1.5V. The quiescent current is approximately 100µA and the buffer can deliver up to 40µ of output current with excellent linearity. Integrator The integrator amplifier, similar to the buffer amplifier, can deliver 20µA of output current with high linearity while swinging to within 0.3V of either supply rail. The integrator’s non-inverting terminal is connected to IN LO during the signal integrate phase, so the voltage on the IN LO terminal sets the starting point for the integrator output during signal integrate. If IN LO is at a voltage other than ground, this will limit the maximum allowable swing at the integrator output, and the value of the integrating capacitor should be increased. (Refer to Component Selection) www.maximintegrated.com Comparator The comparator monitors the voltage on the integrator capacitor during deintegrate. The digital section samples the comparator output once per clock cycle and terminates the deintegrate cycle when the comparator changes its state as the integrator voltage passes through zero. The offset voltage of the comparator is not critical since the auto-zero phase compensates for the offset. The output of the comparator is the only output from the analog section to the digital section. Digital Section As shown in Figure 3, the digital section consists of counters, latches, output multiplexer, and control logic. The control logic monitors the counters and the comparator to determine the start of each phase, and sends control signals to the analog section to drive the analog switches to the proper state for each measurement phase. The control section also responds to the external input, RUN/ HOLD, and creates the control outputs; OVERRANGE, UNDERRANGE, BUSY, and STROBE. RUN/HOLD When RUN/HOLD is high or open the ICL7135 will continuously perform conversions with each measurement being 40,002 clock cycles long. When RUN/HOLD goes low, the ICL7135 will complete the measurement in progress then remain in the auto-zero cycle, holding the last reading. If RUN/HOLD goes high after the maximum period assigned to deintegrate, a new conversion will start, with a delay of 1 to 10,001 clock cycles between Maxim Integrated │  5 41/2 Digit A/D Converter with Multiplexed BCD Outputs ICL7135 V+ 11 POLARITY D5 D4 D3 D2 D1 23 12 17 18 19 20 MSB LSB MULTIPLEXER ANALOG SECTION POLARITY FF LATCH LATCH LATCH ZERO CROSS. DET. LATCH 13 B1 14 15 16 B2 B4 B8 LATCH COUNTERS CONTROL LOGIC 24 22 25 27 28 26 21 DIGITAL GND CLOCK IN RUN/ HOLD OVER RANGE UNDER RANGE STROBE BUSY ICL7135 Figure 3. ICL7135 Digital Section the rising edge of the RUN/HOLD input and the BUSY output. A RUN/HOLD pulse during the unused portion of deintegrate phase will be ignored, but when in the autozero phase a positive pulse of only 300ns (typical) will start the conversion. Figure 5 shows a simple method of obtaining one, and only one, conversion for each measurement request. INTEGRATOR OUTPUT AUTOZERO + ZERO INTEGRATOR 10,0001 COUNTS SIGNAL INT. 10,000 COUNTS DE-INTEGRATE 20,001 COUNTS MAX. FULL MEASUREMENT CYCLE 40,002 COUNTS BUSY BUSY OVER-RANGE WHEN APPLICABLE UNDER-RANGE WHEN APPLICABLE D5 NORMAL DIGIT SCAN D4 D3 D2 D1 1000* COUNTS *FIRST D5 OF AZ AND DE-INTEGRATE ARE ONE COUNT LONGER BUSY is a status output that goes high at the beginning of signal integrate and stays high until the first clock pulse after zero crossing during De-integrate (or end of De-Integrate if overranged).The internal data latches are loaded during the next clock cycle after the falling edge of BUSY. Since BUSY is high for the 10,000 counts of signal integrate + number of counts during De-Integrate +1 clock cycle, a simple way of sending conversion data down a single pair of wires is to logically ‘AND’ BUSY with the clock and to subtract 10,001 counts from the number received. Figure 6 shows a system using this method to remotely display data. *STROBE DIGIT SCAN FOR OVER-RANGE AUTO ZERO D5 SIGNAL INTEGRATE DE-INTEGRATE START PULSE S D Q FLIP-FLOP D4 D3 RUN/HOLD ICL7135 BUSY D2 R D D1 Figure 4. Timing Diagram www.maximintegrated.com Figure 5. External RUN/HOLD Latch Maxim Integrated │  6 41/2 Digit A/D Converter with Multiplexed BCD Outputs ICL7135 Polarity 120kHz CLOCK CLK IN ICL7135 TO REMOTE COUNTER Component Selection BUSY # OF PULSES = 10,001 + READING Figure 6. Serial Pulse Stream for Remote Reading Digit Outputs The digit outputs go high sequentially, D5 to D1, for a period of 200 clock cycles per digit. The 5 digits are continuously scanned except after an over-range measurement. After an over-range reading the digit scan stops after the strobe sequence, and remains stopped until the start of De-Integrate. For a continuous series of over-range readings, the digits will be scanned for 21,000 counts out of 40,002, resulting in a flashing display as an over-range indicator. D5 is the most significant digit. BCD Outputs The 4 BCD output pins are positive logic signals whose BCD data corresponds to the currently active digit strobe. The ICL7135 does not have inter-digit blanking and the BCD data changes simultaneously with the edges of the digit outputs. STROBE The STROBE output is a negative going pulse that is useful for latching the multiplexed BCD outputs into external BCD latches. Five negative going STROBE pulses occur in the center of the data corresponding to each of the 5 digits of measurement results, once and only once after the end of each conversion (immediately after the falling edge of BUSY). The BCD data is valid at both edges of STROBE, and data can be latched in either a level sensitive latch, or an edge triggered latch. Figures 11, 12 and 14 show the use of STROBE to latch the BCD data. STROBE pulse width is 1µs less than 1/2 clock period. Over-range and Under-range Outputs These active high status outputs are set to a high level at the end of BUSY if the measurement result is 1800 or less (Under-range), or greater than 19,999 (Overrange). Under-range is reset at the beginning of the signal integrate phase; over-range is reset at the beginning of the de-integrate phase. www.maximintegrated.com The Polarity output is updated at the beginning of each de-integrate phase, and is high for a positive input signal. The Polarity output is valid for all inputs, including ±0 and overrange signals. The analog component values must be selected with care to achieve optimum performance in each application. Factors that affect the proper values include the reading rate, input common mode voltage, the full scale and reference voltages, and the power supply voltages. Integrating Resistor Good linearity is obtained when the integrating resistor value is chosen such that the buffer’s maximum output current is between 5 and 40µA. The quiescent current of the buffer is 100µA, and it can supply 20µA of output current with excellent linearity. The buffer’s maximum output current occurs with a full scale input voltage, and the integrating resistor value may be calculated as: full scale voltage R INT = 20µA Integrating Capacitor The maximum swing of the integrator during the signal integrate phase can be calculated as: I x TINT Vswing = INT C INT Where IINT = 20µA if RINT is chosen as described above and TINT = 10,000 clock periods (83.3ms for 120kHz clock frequency). The integrator swing range should be maximized while avoiding saturation of the integrator output. Normally the integrator will not saturate until its output is within 0.3V of either supply, but for the best integral linearity the integrator’s output should remain at least 1V away from either supply. For ±5V supply and Analog Common and IN LO connected to ground, a ±3.5V to ±4V swing range is optimum. Rearranging the above formula and inserting values as described above, CINT may be calculated as: 20µA x 83.3ms C INT = x 0.47µF 3.5V The integrator swing must be reduced if either Analog Common or IN LO is not grounded, or if the supply voltage is less than ±5V. The integrating capacitor must have low dielectric absorption to obtain low integral nonlinearity, rollover, and ratio metric errors. The result of measurements with the reference tied to the IN HI is a good indication of the Maxim Integrated │  7 41/2 Digit A/D Converter with Multiplexed BCD Outputs ICL7135 amount of dielectric absorption in the integrating capacitor. A good integrating capacitor will result in a reading of 9999, and any deviation from this reading is probably due to dielectric absorption. Polypropylene capacitors have been found to be suitable, as have Teflon capacitors. Polystyrene and polycarbonate capacitors may also be used in less critical applications. Auto-Zero Capacitor The size of the auto-zero capacitor will have a significant effect on the overall system noise, with larger auto-zero capacitors resulting in a quieter system. The dielectric absorption of the auto-zero capacitor affects only the speed of settling at power-up or recovery from overload and nearly any capacitor type can be used. The zero integrator phase of the ICL7135 allows the use of large auto-zero capacitors while avoiding the “over-range hangover” and hysteresis effects that occur in A/D converters without the zero integrator phase. Reference Capacitor Like the auto-zero capacitor, the reference capacitor’s dielectric absorption is rarely critical. Low dielectric absorption reference capacitors are only required where fast settling time is needed in systems with a rapidly changing reference voltage such as ratiometric ohms measurement in multimeters. The reference capacitor DOES need to be a low leakage capacitor since it must store the reference voltage while floating during both the signal integrate and the reference deintegrate phases. Any leakage or charge loss during these two phases results in an effective change in the scale factor of the ICL7135. Low cost film capacitors such as polyester or polystyrene have been found to be suitable in most applications. In addition to leakage requirements, another effect that sets a lower limit on the value of the reference capacitor is the “charge suckout” caused by stray capacitance on the reference capacitor terminals. For a negative polarity V+ V- 6.8 VOLT ZENER ICL7135 REF HI ANALOG COMMON IZ V- ICL7135 REF HI ANALOG COMMON V- Figure 7. External Reference Voltage www.maximintegrated.com 20 kΩ 6.8kΩ 1.2 BANDGAP REFERENCE input signal, the reference capacitor does not shift its common mode voltage, but with a positive polarity input signal it undergoes mode shift equal to the reference voltage. If there are stray capacitances on the reference capacitor terminals, some of the charge on the reference capacitor will be used to charge these stray capacitances as the reference capacitor makes this common mode voltage shift. This loss of charge reduces the voltage on the reference capacitor, and causes positive polarity signals to have a higher measured result than a corresponding negative voltage. This error can be reduced by minimizing the stray capacitance on the reference capacitor terminals, and by increasing the value of the reference capacitor. Reference Voltage The full scale reading of 20,000 will occur when VIN = 2 x VREF. Since the 20,000 count resolution of the ICL7135 is equivalent to a 50ppm resolution, a high stability reference is recommended for high accuracy absolute measurements. Figure 7 shows two suitable methods of generating the reference voltage. Rollover Resistor and Diode The ICL7135 is tested for rollover using the circuit of Figure 1, with the 100kΩ resistor and diode in the circuit. The diode is noncritical, and is typically a low cost 1N4148. The resistor value is dependent on many factors including integrator swing, clock frequency, and the amount of rollover error due to “charge suckout” on the reference capacitor. 100kΩ is the optimum value for most circuits and is the value used in testing the ICL7135. Speedup Resistor The 27Ω speedup resistor in series with the integrating capacitor adds a pedestal voltage on top of the integrating capacitor voltage. This pedestal voltage causes zero crossing to occur earlier than would occur without the resistor. The effect of the earlier zero crossing is to give the comparator an overdrive voltage, speeding its response and reducing the conversion error due to comparator delay. If the integrator current is changed, the speedup resistor value should be changed so that the IINT x RSPEEDUP = 500µV. Clock Frequency The clock source should be free of short-term phase and frequency jitter during the conversion period, but long term stability is not critical. The clock frequency is chosen to obtain the desired conversion rate, and to maximize the normal mode rejection of power line frequency interference. The conversion rate is directly proportional to the clock frequency, with each conversion taking 40,002 clock cycles. For maximum normal mode rejection, Maxim Integrated │  8 41/2 Digit A/D Converter with Multiplexed BCD Outputs ICL7135 the signal integration period should be an integral multiple of the power line cycles. Application Hints Reading Rate (in readings per second) = As with all sensitive analog circuitry, it is important to keep the Digital Ground separate from the .analog ground (called Analog Common on the ICL7135) to minimize errors caused by the coupling of noise from the digital circuitry into the sensitive analog section. Analog Common should be connected to Digital Ground at only one point, and return currents from digital loads must not flow through the analog ground lines. Avoid any unnecessary current flow in the analog ground path. f CLK 40,002 f x 10,000 f CLK for maximum normal mode rejection = LINE N Where fLINE is the line frequency, normally 50Hz or 60Hz and N is the number of line cycles that occur during a signal integration period. For maximum normal mode rejection, N should be an integer. For 60Hz rejection, suitable clock frequencies include 300kHz, 200kHz, 150kHz, 120kHz, 100kHz, and 75kHz. Suitable frequencies for use with 50Hz power include 250kHz , 1662/3kHz, 125kHz, and 100kHz. The two most common clock frequencies are 120kHz (3 readings per second) and 100kHz (21/2 readings per second). Note that a 100kHz clock frequency rejects both 50Hz and 60Hz normal mode signals. The maximum clock rate is limited by the maximum rate at which the digital logic will correctly function (typically 2MHz), and by the speed of response of the comparator. The comparator delay, about 3µs, has the same effect on the measurement result as does an offset voltage with the same polarity of the input signal. At the recommended clock frequency of 120kHz, this small offset is slightly less than 1/2 count. At higher clock frequencies the value of the speedup resistor in series with the integration capacitor (normally 27Ω) should be increased. At frequencies above 120kHz, ringing on the integrator output may cause nonlinearities in the first few counts. The minimum clock frequency is limited by the leakage of the auto-zero and reference capacitors. While seldom desired, measurement cycles as long as 10 seconds can be performed with negligible error at room temperature. Figures 8A and 8B show two methods of generating a suitable clock signal for the ICL7135. Grounds Single 5V Supply Operation The ICL7135 normally uses ±5V supplies, however, in some applications the negative supply is not needed. Specifically, the negative 5V supply is not required if the input signal can be referenced to the center of the ICL7135’s common mode voltage range AND the signal voltage is less than ±1.5V. The integrator swing must be reduced, and there will be a slight increase in system noise and nonlinearity. See Figure 9 for recommended component values. SET VREF = 1.000V VREF IN 1 V100kΩ 1.0µF 2.0µF 100kΩ 100kΩ 1µF 100kΩ OVERRANGE 27 3 ANALOG COMMON 27Ω 2.5V SIGNAL INPUT UNDERRANGE 28 2 REFERENCE 4 INT. OUT 5 A-Z IN DIGITAL GND 24 6 BUFF OUT POLARITY 23 7 REF. CAP- ICL7135 CLOCK IN 22 8 REF. CAP+ 0.1µF -5V LSD D1 20 10 IN HI D2 19 11 V+ D3 18 12 MSD D5 13 LSB B1 56kΩ 3 4 16kΩ 7 1 MAX4069 CMOS INVERTOR TO ICL7135 CLOCK IN www.maximintegrated.com B4 15 MAX4069 TO ICL7135 CLOCK IN 22MΩ 30kΩ 100kHz OR 120kHz 390pF 5pF Figure 8A. LM311 Clock Source D4 17 MSB B8 16 +5 1kΩ 8 2 LM311 CLOCK IN 120kHz Figure 9. Single +5V Supply Operation +5V 0.22µF BUSY 21 9 IN LO 14 B2 16kΩ STROBE 26 RUN/HOLD 25 TUNING FORK CRYSTAL 330kΩ 10pF Figure 8B. Crystal Oscillator Clock Source Maxim Integrated │  9 41/2 Digit A/D Converter with Multiplexed BCD Outputs ICL7135 Generating a Negative Supply from +5V Figures 10A and 10B show two methods of generating a negative supply for the ICL7135. The Maxim ICL7660 will supply 2mA (the maximum supply current of the ICL7135) at 4.85V drop, while the circuit using the CMOS inverter will deliver approximately -3.5V. If the CMOS inverter is used to generate a minus supply, the integrator swing should be reduced to 2.5 to 3V. Noise The normal system noise around zero is about 15µV peak-to-peak (not exceeded 95% of the time). Near full scale, the noise increases to about 30µV. The main noise source is the auto-zero loop, and increasing the value of the auto-zero capacitor will reduce the noise. Other noise sources include the buffer and integrator noise; comparator noise; and stray pickup in the input circuitry, the integrator, and the reference capacitor. The noise caused by stray pickup of interfering signals can be reduced by a tight layout and shielding. If the interfering signal frequency is constant, the effects of stray pickup in the input and integrator can be reduced by choosing a clock frequency such that the signal integration period is an integral multiple of the interfering signal’s period. Since the length of the de-integration period depends on the input signal level, no single clock frequency can be chosen to reject interfering signals during the de-integrate phase. Typical Applications Figure 11 uses Maxim’s ICL7211 LCD display driver to drive 4 digits of LCD display. The backplane signal of the ICL7211 and the CMOS exclusive OR gates are used to drive the 1/2 digit and the polarity sign. The four AND gates combine the digit outputs with the STROBE output to generate the digit select signals that latch data into the ICL7211. Since the Strobe occurs in the middle of each digit’s data there is ample data setup and hold time to ensure that valid data is latched. The OR gates will force the BCD data to all ones when over-range goes high. The ICL7211A will blank the display when all ones (hexF is loaded). The typical operating circuit on the first page of this data sheet shows a 41/2 digit A/D with LED drive using the Maxim ICL7212 display driver. In this case the polarity and 1/2 digit segments are driven by D flip-flops that latch polarity and 1/2 digit data at the end of each measurement. The ICL7135 Overrange output drives the ICM7212 Brightness input, blanking the four least significant digits when the input voltage is greater than full­scale. Some applications require non-multiplexed, latched BCD outputs. The circuit shown in Figure 12 will demultiplex and latch the ICL7135 output. If only the first rank of latches is used, the data should not be used during the 800 clock cycle update period that takes place at the end of each conversion since during this update period the -5V 1 2 10µF 3 8 ICL7660 4 7 6 5 BP VOUT = -5V 1/2 CD4030 23 POL 100µF 20 19 18 17 Figure 10A. Generating a Negative Supply 120 kHz CLOCK V+ D1 D2 D3 D4 16 B8 CD4081 1/4 CD4030 CD4071 CD 4009 0.47µF IN914 10µF ICL7135 IN914 31 32 33 34 D1 D2 D3 D4 28 B1 27 B0 CD4011 12 D5 26 STROBE 27 OR ICL7135 5 BP 30 B3 29 B2 15 B4 14 B2 13 B1 CLOCK V- 4-1/2 DIGIT LCD DISPLAY +5V ICM7211A +5V 1/4 CD4030 Figure 11. LCD Display with Digit Blanking on Overrange GND V- = -3.5V Figure 10B. Generating a Negative Supply www.maximintegrated.com Maxim Integrated │  10 41/2 Digit A/D Converter with Multiplexed BCD Outputs ICL7135 most significant digit (MSD) data will correspond to the new reading and the least significant digit (LSD) data will be old data from the previous conversion. The second rank of latches shown in dotted lines will eliminate this problem by updating all digits simultaneously with the rising edge of D5. There are many different possible ways of interfacing the ICL7135 to a microprocessor. Figure 13 shows a method that uses only 8 I/O lines. The digit outputs drive a priority encoder, which converts the 1-of-5 format of the digit outputs to a 3 bit binary code. When no digit is active (as in over-range), the binary output code is 0, otherwise the output corresponds to the digit number of the active digit. By sending BUSY as either an input or an an interrupt, the microprocessor can detect when new data is available. Another possible interface scheme is to sense only digit D5, then use time delays to choose when to read the other digits’ data. B1 B2 B4 B8 D1 D2 B1 B2 B4 B8 POL OR ICL7135 STROBE D5 D4 D3 B1 B2 B4 B8 B1 B2 B4 B8 B1 B2 B4 B8 B1 D0 E0 D1 D2 E2 Q0 74LS375 D3 D1 D2 Q0 Q2 Q3 D0 E0 D0 Q1 74LS374 E2 Q0 74LS375 D3 DIGIT 2 BCD DATA Q1 Q2 Q3 DIGIT 1 BCD DATA D7 Q7 Interfacing with UARTs and Microprocessors Figure 14 shows a simple interface between a UART and a free running ICL7135. The transmission of the five data words is started by the five STROBE pulses. The digit 5 word is 0000XXXX, digit 4 is 1000XXXX, digit 3 is 0100XXXX, etc. The polarity is transmitted indirectly by using it to drive the Even Parity Enable Pin (EPE). A parity flag at the receiver can be decoded as a positive signal, no flag as negative, if EPE of the receiver is held low. Figure 15 shows a more complex arrangement. DR goes high when the UART receives a byte via the send input, RRI. Since DR is connected to the ICL7135’S RUN/ HOLD input this starts a new conversion. At the end of the conversion the falling edge of BUSY resets DR via the UART’S DRR input. The transmit sequence is again started by STROBE. A quad 2-input multiplexer is used to superimpose polarity, over-range, and under-range onto the D5 word since in this instance it is known that B2 = B4 = B8 = 0. To insure proper operation, it is necessary that the UART clock be fast enough that each word is transmitted before the next STROBE pulse arrives. B1 B2 B4 B8 ICL7135 D1 D2 D3 D4 D5 P10 P11 P12 P13 MAX8048 D1 Q0 MC D2 14532 Q1 D3 PRIORITY Q2 D4 ENCODER D5 P1 P15 P16 INT P17 BUSY Q0 D0 D1 D2 74LS375 D3 E0 D2 Q0 Q1 Q2 E2 Q3 74LS375 D3 E0 Figure 13. µP Interface SERIAL OUTPUT TO RECEIVING UART DIGIT 4 BCD DATA Q1 Q2 E2 Q3 DIGIT 3 BCD DATA 74LS374 Q0 D0 D1 D0 D7 Q7 EPE 1 D0 Q0 Q1 D1 74LS375 D2 Q2 Q3 D3 E0 E2 D0 Q0 D3 Q3 www.maximintegrated.com 2 3 4 5 TBRL 6 7 8 DIGIT 5 DATA POLARITY OVERRANGE D4 D3 D2 D1 B1 B2 B4 B6 NC D5 POL Figure 12. Non-Multiplexed, Latched BCD Output TRO UART TR1602 TBR ICL7135 STROBE RUN/HOLD +5V Figure 14. ICL7135 to UART Interface Maxim Integrated │  11 41/2 Digit A/D Converter with Multiplexed BCD Outputs ICL7135 Chip Topography TRO EPE 1 RRI DRR TR1602 TBR 2 3 4 5 0.134” (3.40mm) STROBE ANALOG UNDERRANGE COMMON REF VOVERRANGE DR TBRL 6 7 8 1Y 2Y 3Y D4 D3 D2 D1 B1 D5 B2 B4 B8 SELECT 1A 2A 3A 2 1 28 27 26 ENABLE 25 5 AZ IN 1B 2B 3B ICL7135 IN HI RUN/HOLD 10kΩ BUSY 23 22 8 9 REF CAP+ IN LO STROBE 24 6 7 BUFF OUT REF CAPPOL OVER UNDER 74C157 3 4 INT OUT 21 20 10 +5V 19 11 V+ 100pF R/H DIGITAL GND POL CLOCK IN 0.155” (2.92mm) BUSY D1 D2 12 13 14 15 16 17 18 D5 B1 B2 B4 B8 D4 D3 Figure 15. Complex ICL7135 to UART Interface 0.070 (1.778) 0.600 - 0.620 (15.240 - 15.748) 0.580 (14.730) MIN 0.025 (0.635) 1.470 MAX (37.340) 0.062 (1.575) RAD RAD 0.030 (0.762) MAX 0.540 ± 0.005 (13.720 ± 0.127) 0.040 TYP (1.016) 0.590 - 0.620 (14.986 - 15.748) 0.100 ± 0.010 (2.540 ± 0.254) 0.600 MAX GLASS (15.240) 0.530 - 0.550 (13.462 - 13.970) 86° 94° TYP 0.125 (3.175) MIN 0.160 0.100 ± 0.010 TYP (4.064) (2.540 ± 0.254) MAX 95°±5° 95°± 5° 0.625 +0.025 -0.015 (15.875 +0.635 -0.381 ) 1.490 MAX (37.846) 0.050 ± 0.015 (1.270 ± 0.381) 86° 94° TYP 0.009 - 0.015 (1.229 - 0.381) 0.685 ± 0.025 (17.399 ± 0.635) 0.150 ± 0.005 0.125 0.020 (3.810 ± 0.127) (3.175) (0.508) MIN MIN 0.018 ± 0.003 (0.457 ± 0.076) TYP 0.008 ± 0.012 (0.203 - 0.305) 0.055 ± 0.005 (1.397 ± 0.127) 28 Lead Plastic (PI) θJA = 110°C/W, θJC = 50°C/W 0.045 (1.143) 0.018 ± 0.002 (0.457 ± 0.051) TYP 0.060 - 0.100 (1.524 - 2.540) GLASS SEALANT 0.020 - 0.070 (0508 - 1.778) 0.200 (5.080) MAX 0.125 (3.175) MIN 0.048 - 0.055 (1.219 - 1.397) 28 Lead Cerdip (JI) θJA = 55°C/W 0.449 ± 0.001 (11.405 ± 0.025) 0.045 0.010 (1.143) (0.254) PIN 1 0.010 (0.254) 0.045 (1.143) 0.490 ± 0.005 (12.446 ± 0.127) 0.050 BC 0.070 (1.778) 0.045 (1.143) 0.010 (0.254) 0.172 ± 0.003 (4.369 ± 0.076 0.035 RAD (0.889) 0.420 ± 0.005 (10.668 ± 0.127) 0.022 (0.559) 0.145 (3.683) 28 Lead Plastic Chip Carrier (Quad Pak) (Q) www.maximintegrated.com Maxim Integrated │  12 41/2 Digit A/D Converter with Multiplexed BCD Outputs ICL7135 Revision History REVISION NUMBER REVISION DATE PAGES CHANGED 0 2/87 Initial release — 1 9/16 Updated Ratiometric Reading minimum specification in Electrical Characteristics table 2 DESCRIPTION For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com. Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. ©  2016 Maxim Integrated Products, Inc. │  13