ABRIDGED DATA SHEET
EVALUATION KIT AVAILABLE
MAX14676/MAX14676A
Wearable Charge Management Solution
General Description
The MAX14676/MAX14676A are battery-chargemanagement solutions ideal for low-power wearable
applications. These devices include a linear batterycharger with a Smart Power Selector™, ModelGauge™
fuel gauge, and several power-optimized peripherals.
They feature an ultra-low-power buck regulator with a
quiescent current of 900nA (typical) and 74% efficiency
with 10µA output.
The battery charger features Smart Power Selector
operation, allowing operation with dead battery. It limits
input current based on a register setting. If the charger
power source is unable to supply the entire system load,
the smart power control circuit will supplement the system
load with current from the battery.
The MAX14676/MAX14676A embed a Maxim proprietary
ModelGauge fuel gauge to provide an accurate estimate
of the available capacity for rechargeable lithium batteries.
The MAX14676/MAX14676A include a synchronous highefficiency step-down converter. The device features a fixedfrequency PWM mode for tighter regulation, and a burst
mode for increased efficiency during light-load operation.
The MAX14676/MAX14676A have a boost regulator and
three programmable current sinks that can be used to
drive a variety of LED configurations. The boost converter
is controlled independently from the current sinks, and
they can be also used separately.
The MAX14676/MAX14676A feature a power switch controller that allows the device to be turned on and off by a
pushbutton. This controller also provides a delayed reset
signal and voltage sequencing.
These devices are available in a 42-bump, 0.5mm pitch,
3.497mm x 3.118mm wafer-level package (WLP).
Smart Power Selector and ModelGauge are trademarks of
Maxim Integrated Products, Inc.
19-6856; Rev 3; 5/17
Benefits and Features
●● Extend System Use Time Between Battery Charging
• 1.8V Low-IQ 200mA Buck Regulator
• - 0.9μA (typ) Quiescent Current
• - Automatic Burst or Forced-PWM Modes
• ModelGauge with Accurate State-of-Charge
●● Easy-to-Implement Li+ Battery Charging
• Smart Power Selector
• 28V Tolerant Input
• Thermistor Monitor
●● Minimize Power-Management Footprint though High
Integration
• 3.2V Low-IQ 100mA LDO
• 2.0V Always-On 50μA LDO
• +5V Safe Output LDO
• 6.6V Low-IQ 120μA Charge Pump
●● Support a Wide Variety of Display Options
• 5V to 17V Output Boost Converter
• 3-Channel Adjustable High-Voltage Current Sinks
●● Optimize System Control
• Pushbutton to Enable Ultra-Low-Power Mode and
Power-On Voltage Sequencing
• I2C Control
Applications
●●
●●
●●
●●
Wearable Electronics
GPS Watches
Fitness Monitors
Portable Medical Devices
Ordering Information/Selector Guide appears at end of
data sheet.
ABRIDGED DATA SHEET
MAX14676/MAX14676A
Wearable Charge Management Solution
Typical Application Circuit
VIO
+2.0V
VIO
MAX14676/MAX14676A
ALRT
ALRT
RST
CTG
KOUT
QSTRT
FUEL GAUGE
POWER SWITCH
CELL
RST
KEY
KIN
0.1µF
AOLDO
0.1µF
CAP
NVP
1
CHGIN
1µF
Li+ BATTERY CHARGER WITH
SMART POWER SELECTOR
GND
+5V
SFOUT
THM
BAT
GND
SYS
5V LDO
1µF
BOUT
VIO
1.8V BUCK
1µF
1µF
VSYS
+1.8V
BLX
2.2µH
SCL
SCL
3.2V
LDO
SDA
SDA
INT
INT
MPC0
MPC0
CONTROL
VSYS
+12V
6.6V
CHARGE PUMP
LED0
LED1
LED2
LOUT
CPOUT
MPC1
MPC1
10µF
+3.2V
+6.6V
CPP
CPN
10µF
15µF
1µF
27nF
VSYS
HVLX
CURRENT
SINKS
BOOST
HVOUT
3.3µH
HVCAP
+12V
4.7µF
4.7µF
BUZZER
GND
NOTE 1: OPTIONAL FOR REVERSE VOLTAGE PROTECTION
www.maximintegrated.com
Maxim Integrated │ 2
ABRIDGED DATA SHEET
MAX14676/MAX14676A
Wearable Charge Management Solution
Ordering Information/Selector Guide
PART
BUCK
3.2V LDO
STAY ON BIT DEFAULT*
BUMP-PACKAGE
MAX14676EWO+T
Forced On
Forced On
0
42 WLP
MAX14676AEWO+T
Forced On
Off (default)
1
42 WLP
+ Denotes lead(Pb)-free/RoHS compliant package.
T = Tape and reel.
*See Table 29 for the StayOn bit default settings.
Chip Information
PROCESS: BiCMOS
www.maximintegrated.com
Maxim Integrated │ 49
很抱歉,暂时无法提供与“MAX14676EWO+T”相匹配的价格&库存,您可以联系我们找货
免费人工找货