MAX17021EVKIT+

19-4511; Rev 0; 3/09 MAX17021 Evaluation Kit Features The MAX17021 evaluation kit (EV kit) demonstrates the high-power, dynamically adjustable, multiphase IMVP-6.5+ notebook CPU application circuit. This DC-DC converter steps down high-voltage batteries and/or AC adapters, generating a precision, low-voltage CPU core VCC rail. The MAX17021 EV kit meets the Intel mobile IMVP-6+ CPU’s transient voltage specification, power-good signaling, voltage regulator thermal monitoring (VRHOT), and power-good output (PWRGD). The MAX17021 kit consists of the MAX17021 2-phase interleaved Quick-PWM™ step-down controller. The MAX17021 kit includes active voltage positioning with adjustable gain, reducing power dissipation and bulk output capacitance requirements. A slew-rate controller allows controlled transitions between VID codes, controlled soft-start and shutdown, and controlled exit suspend voltage. Precision slew-rate control provides “just-in-time” arrival at the new DAC setting, minimizing surge currents to and from the battery. Two dedicated system inputs (PSI and DPRSLPVR) dynamically select the operating mode and number of active phases, optimizing the overall efficiency during the CPU’s active and sleep states. o Dual-Phase, Fast-Response Interleaved, Quick-PWM o Intel IMVP-6+ Code-Set Compliant (Montevina Socket Configuration) o Dynamic Phase Selection Optimizes Active/Sleep Efficiency o Transient Phase Overlap Reduces Output Capacitance o Active Voltage Positioning with Adjustable Gain o High Speed, Accuracy, and Efficiency o Low-Bulk Output Capacitor Count o 7V to 24V Input-Voltage Range o 0 to 1.5000V Output-Voltage Range (7-Bit DAC) o 60A Peak Load-Current Capability (30A Each Phase) o Accurate Current Balance and Current Limit o 300kHz Switching Frequency (per Phase) o Power-Good (PWRGD) and Phase-Good (PHASEGD) Outputs and Indicators o Clock Enable (CLKEN) and Thermal Fault (VRHOT) Outputs and Indicators o Output Overvoltage and Undervoltage Fault Protections o 40-Pin Thin QFN Package with Exposed Pad o Lead(Pb)-Free and RoHS Compliant o Fully Assembled and Tested The MAX17021 includes latched output undervoltagefault protection, overvoltage-fault protection, and thermal-overload protection. It also includes a voltage regulator power-good (PWRGD) output, a clock enable (CLKEN) output, and a phase-good (PHASEGD) output. This fully assembled and tested circuit board provides a digitally adjustable 0 to 1.5000V output voltage (7-bit on-board DAC) from a 7V to 24V battery input range. Each phase is designed for a 20A thermal design current, and delivers up to 30A peak output current for a total of 60A. The EV kit operates at 300kHz switching frequency (per phase) and has superior line- and loadtransient response. Ordering Information PART TYPE MAX17021EVKIT+ EV Kit +Denotes lead(Pb)-free and RoHS compliant. Component List DESIGNATION CLKEN, DPRSLPVR, GND_SENSE, PGDIN, PHASEGD, PSI, PWRGD, V3P3, VOUT_SENSE, VRHOT, VR_ON QTY 11 DESCRIPTION Test points DESIGNATION C1–C4 QTY 4 DESCRIPTION 10µF ±20%, 25V X5R ceramic capacitors (1210) Murata GRM32DR61E106KA12L TDK C3225X7R1E106M AVX 12103D106M Taiyo Yuden TMK325BJ106MM KEMET C1210C106M3RAC Quick-PWM is a trademark of Maxim Integrated Products, Inc. ________________________________________________________________ Maxim Integrated Products For information on other Maxim products, visit Maxim’s website at www.maxim-ic.com. 1 Evaluates: MAX17021 General Description Evaluates: MAX17021 MAX17021 Evaluation Kit Component List (continued) DESIGNATION QTY DESCRIPTION C5–C8 4 330µF, 2V, 4.5m
low-ESR polymer capacitors (D case) Panasonic EEFSX0D331E4 or NEC TOKIN PSGV0E337M4.5 KEMET T520V337M2R5ATE4R5 C9 0 Not installed, ceramic capacitor (0805) 2 C10, C11 C12, C20–C27 C13–C16, C28, C29 C17, C18, C19 C30–C39, C62–C65 C40–C49 2 0 6 3 14 10 DESIGNATION QTY DESCRIPTION L1, L2 2 0.36µH, 36A, 0.82m
power inductors Panasonic ETQP4LR36ZFJ NEC TOKIN MPC1055LR36 TOKO FDUE1040D-R36M N1, N2 2 1µF ±10%, 16V X5R ceramic capacitors (0603) TDK C1608X5R1C105K Taiyo Yuden EMK107BJ683MA Murata GRM188R61C105K n-channel MOSFETs (PowerPAK 8 SO) Fairchild FDS6298 (8 SO) Vishay (Siliconix) SI4386DY N3–N6 4 n-channel MOSFETs (PowerPAK 8 SO) Fairchild FDS8670 (8 SO) Vishay (Siliconix) SI4626ADY N7 0 Not installed, ceramic capacitors (0603) C12, C20–C26 are open; C27 is short (PC trace) Not installed, n-channel MOSFET (D-PAK) N8, N9 0 Not installed, n-channel MOSFETs (PowerPAK 8 SO) R1, R15, R16, R43, R44 5 10
±5% resistors (0603) R2 1 59k
±1% resistor (0603) 0.22µF ±20%, 10V X7R ceramic capacitors (0603) Murata GRM188R71A224K Taiyo Yuden LMK107BJ224MA TDK C1608X7R1C224M AVX 06033D224KAT 1000pF ±10%, 50V X7R ceramic capacitors (0603) TDK C1608X7R1H102K or Murata GRM188R71H102K or equivalent 10µF ±20%, 6.3V X5R ceramic capacitors (0805) TDK C2012X5R0J106M or Taiyo Yuden AMK212BJ106MG AVX 08056D106MAT 22µF, 6.3V X5R ceramic capacitors (0805) TDK C2012X5R0J226MT Taiyo Yuden JMK212BJ226MG D1, D2 2 3A, 30V Schottky diodes Nihon EC31QS03L Central Semi CMSH3-40M D3–D6 4 LEDs, green clear SMD (0805) LITE-ON Electronics LTST-C170GKT Digi-Key 160-1179-1-ND JU1 0 Not installed, 3-pin header R3 1 12.1k
±1% resistor (0603) R4 1 200k
±1% resistor (0603) R5, R6 2 0
resistors (0603) R7, R11 2 1.21k
±1% resistors (0603) R8, R12 2 1.50k
±1% resistors (0603) R9, R13 2 20k
±1% resistors (0603) R10, R14 2 10k
±1% NTC thermistors, ß = 3380 (0603) Murata NCP18XH103F03RB TDK NTCG163JH103F R17 1 4.32k
±1% resistor (0603) R18, R24, R33, R34, R35, 0 Not installed, resistors (0603) R18, R24, and R33 are open; R34 and R35 are short (PC trace) R19 1 51
±5% resistor (0603) R20 0 Not installed, 1W resistor (2512) R21, R22, R23, R30 4 1k
±5% resistors (0603) R25 1 13k
±1% resistor (0603) 1 100k
±5% NTC thermistor, ß = 4250 (0603) Murata NCP18WF104J03RB TDK NTCG163JF104J (0402) or Panasonic ERT-J1VR104J R26 _______________________________________________________________________________________ MAX17021 Evaluation Kit DESIGNATION QTY R27, R28, R29, R31, R32, R36–R42 12 R45, R46 DESCRIPTION DESIGNATION QTY DESCRIPTION 100k
±5% resistors (0603) U1 1 Dual-phase, Quick-PWM VID controller (40 TQFN-EP*) Maxim MAX17021GTL+ 2 2
±5% resistors (0603) U2 1 CPU socket MPGA479 SW1 1 7-position low-profile DIP switch — 1 PCB: MAX17021 Evaluation Kit+ SW2 1 5-position low-profile DIP switch *EP = Exposed pad. Component Suppliers SUPPLIER PHONE WEBSITE AVX Corporation 843-946-0238 www.avxcorp.com Central Semiconductor Corp. 631-435-1110 www.centralsemi.com Digi-Key Corp. 800-344-4539 www.digikey.com Fairchild Semiconductor KEMET Corp. 888-522-5372 864-963-6300 www.fairchildsemi.com www.kemet.com Murata Electronics North America, Inc. 770-436-1300 www.murata-northamerica.com NEC TOKIN America, Inc. 408-324-1790 www.nec-tokinamerica.com Nihon Inter Electronics Corp. 847-843-7500 www.niec.co.jp Panasonic Corp. 800-344-2112 www.panasonic.com Taiyo Yuden 800-348-2496 www.t-yuden.com TDK Corp. 847-803-6100 www.component.tdk.com TOKO America, Inc. 847-297-0070 www.tokoam.com Vishay 402-563-6866 www.vishay.com Note: Indicate that you are using the MAX17021 when contacting these component suppliers. Quick Start Recommended Equipment • MAX17021 EV kit • 7V to 24V, > 100W power supply, battery, or notebook AC adapter • DC bias power supply, 5V at 1A • Dummy load capable of sinking 60A • Digital multimeters (DMMs) • 100MHz dual-trace oscilloscope and SW1 (7, 8) to the on positions. The output voltage is set for 1.050V. 3) Turn on the battery power before turning on the 5V bias power. 4) Observe the 1.050V output voltage with the DMM and/or oscilloscope. Look at the LX switching nodes and MOSFET gate-drive signals while varying the load current. Detailed Description of Hardware Procedure The MAX17021 EV kit is fully assembled and tested. Follow the steps below to verify board operation: 1) Ensure that the circuit is connected correctly to the supplies and dummy load prior to applying any power. 2) Verify that all positions of switch SW2 are off. The DAC code settings (D6–D0) are set by switch SW1. Set SW1 (1, 14), SW1 (2, 13), SW1 (4, 11), SW1 (5, 10), This 60A peak multiphase buck-regulator design is optimized for a 300kHz switching frequency (per phase) and output-voltage settings around 1V. At VOUT = 1V and VIN = 12V, the inductor ripple is approximately 35% (LIR = 0.35). The MAX17021 controller interleaves all the active phases, resulting in out-of-phase operation that minimizes the input and output filtering requirements. The multiphase controller shares the current between two phases that operate 180° out-ofphase, supplying up to 30A per phase. _______________________________________________________________________________________ 3 Evaluates: MAX17021 Component List (continued) Evaluates: MAX17021 MAX17021 Evaluation Kit Setting the Output Voltage The MAX17021 has an internal digital-to-analog converter (DAC) that programs the output voltage. The output voltage can be digitally set from 0 to 1.5000V (Table 2) from the D0–D6 pins. There are two different ways of setting the output voltage: 1) Drive the external VID0–VID6 inputs (all SW1 positions are off). The output voltage is set by driving VID0–VID6 with open-drain drivers (pullup resistors are included on the board) or 3V/5V CMOS output logic levels. Table 1. MAX17021 Operating Mode Truth Table INPUTS SHDN DPRSTP DPRSLPVR SW2 SW2 SW2 (1, 10) (5, 6) (2, 9) GND Rising High High High High X X High High Low High X X Low Low High High PSI SW2 (3, 8) PHASE OPERATION* X Disabled X OPERATING MODE Low-Power Shutdown Mode. DL1 and DL2 are forced low and the controller is disabled. The supply current drops to 1µA (max). Multiphase Startup/Boot. When SHDN is pulled high, the MAX17021 begins the Pulse Skipping startup sequence. The controller enables the PWM controller and 1/8 RTIME ramps the output voltage up to the boot voltage. Slew Rate High Multiphase Forced-PWM Normal RTIME Slew Rate Full Power. The no-load output voltage is determined by the selected VID DAC code (D0–D6, Table 2). Low 1-Phase Forced-PWM Normal RTIME Slew Rate Intermediate Power. The no-load output voltage is determined by the selected VID DAC code (D0–D6, Table 2). When PSI is pulled low, the MAX17021 immediately disables phase 2. DH2 and DL2 are pulled low. X 1-Phase Pulse Skipping Normal RTIME Slew Rate Deeper Sleep Mode. The no-load output voltage is determined by the selected VID DAC code (D0–D6, Table 2). When DPRSLPVR is pulled high, the MAX17021 immediately enters 1-phase pulse-skipping operation allowing automatic PWM/PFM switchover under light loads. The PWRGD and CLKEN upper thresholds are blanked during downward transitions. DH2 and DL2 are pulled low. X 1-Phase Pulse Skipping 1/4 RTIME Slew Rate Deeper Sleep Slow Exit Mode. The no-load output voltage is determined by the selected VID DAC code (D0–D6, Table 2). When DPRSTP is pulled high while DPRSLPVR is already high, the MAX17021 remains in one-phase pulse-skipping operation, allowing automatic PWM/PFM switchover under light loads, but reduces its slew rate to 1/4 of normal. Shutdown. When SHDN is pulled low, the MAX17021 immediately pulls PWRGD and PHASEGD low, CLKEN becomes high impedance, all enabled phases are activated, and the output voltage is ramped down to ground. Once the output reaches 0V, the controller enters the low-power shutdown state. Falling X X X Multiphase Forced-PWM 1/8 RTIME Slew Rate High X X X Disabled Fault Mode. The fault latch has been set by the MAX17021 UVP or thermal-shutdown protection, or by the OVP protection. The controller remains in fault mode until VCC power is cycled or SHDN toggled. *Multiphase operation = All enabled phases active. X = Don’t care. 4 _______________________________________________________________________________________ MAX17021 Evaluation Kit Evaluates: MAX17021 Table 2. MAX17021 IMVP-6.5+ Output-Voltage VID DAC Codes D6 D5 D4 D3 D2 D1 D0 OUTPUT VOLTAGE (V) D6 D5 D4 D3 D2 D1 D0 OUTPUT VOLTAGE (V) 0 0 0 0 0 0 0 1.5000 1 0 0 0 0 0 0 0.7000 0 0 0 0 0 0 1 1.4875 1 0 0 0 0 0 1 0.6875 0 0 0 0 0 1 0 1.4750 1 0 0 0 0 1 0 0.6750 0 0 0 0 0 1 1 1.4625 1 0 0 0 0 1 1 0.6625 0 0 0 0 1 0 0 1.4500 1 0 0 0 1 0 0 0.6500 0 0 0 0 1 0 1 1.4375 1 0 0 0 1 0 1 0.6375 0 0 0 0 1 1 0 1.4250 1 0 0 0 1 1 0 0.6250 0 0 0 0 1 1 1 1.4125 1 0 0 0 1 1 1 0.6125 0 0 0 1 0 0 0 1.4000 1 0 0 1 0 0 0 0.6000 0 0 0 1 0 0 1 1.3875 1 0 0 1 0 0 1 0.5875 0 0 0 1 0 1 0 1.3750 1 0 0 1 0 1 0 0.5750 0 0 0 1 0 1 1 1.3625 1 0 0 1 0 1 1 0.5625 0 0 0 1 1 0 0 1.3500 1 0 0 1 1 0 0 0.5500 0 0 0 1 1 0 1 1.3375 1 0 0 1 1 0 1 0.5375 0 0 0 1 1 1 0 1.3250 1 0 0 1 1 1 0 0.5250 0 0 0 1 1 1 1 1.3125 1 0 0 1 1 1 1 0.5125 0 0 1 0 0 0 0 1.3000 1 0 1 0 0 0 0 0.5000 0 0 1 0 0 0 1 1.2875 1 0 1 0 0 0 1 0.4875 0 0 1 0 0 1 0 1.2750 1 0 1 0 0 1 0 0.4750 0 0 1 0 0 1 1 1.2625 1 0 1 0 0 1 1 0.4625 0 0 1 0 1 0 0 1.2500 1 0 1 0 1 0 0 0.4500 0 0 1 0 1 0 1 1.2375 1 0 1 0 1 0 1 0.4375 0 0 1 0 1 1 0 1.2250 1 0 1 0 1 1 0 0.4250 0 0 1 0 1 1 1 1.2125 1 0 1 0 1 1 1 0.4125 0 0 1 1 0 0 0 1.2000 1 0 1 1 0 0 0 0.4000 0 0 1 1 0 0 1 1.1875 1 0 1 1 0 0 1 0.3875 0 0 1 1 0 1 0 1.1750 1 0 1 1 0 1 0 0.3750 0 0 1 1 0 1 1 1.1625 1 0 1 1 0 1 1 0.3625 0 0 1 1 1 0 0 1.1500 1 0 1 1 1 0 0 0.3500 0 0 1 1 1 0 1 1.1375 1 0 1 1 1 0 1 0.3375 0 0 1 1 1 1 0 1.1250 1 0 1 1 1 1 0 0.3250 0 0 1 1 1 1 1 1.1125 1 0 1 1 1 1 1 0.3125 0 1 0 0 0 0 0 1.1000 1 1 0 0 0 0 0 0.3000 0 1 0 0 0 0 1 1.0875 1 1 0 0 0 0 1 0.2875 0 1 0 0 0 1 0 1.0750 1 1 0 0 0 1 0 0.2750 0 1 0 0 0 1 1 1.0625 1 1 0 0 0 1 1 0.2625 0 1 0 0 1 0 0 1.0500 1 1 0 0 1 0 0 0.2500 0 1 0 0 1 0 1 1.0375 1 1 0 0 1 0 1 0.2375 0 1 0 0 1 1 0 1.0250 1 1 0 0 1 1 0 0.2250 0 1 0 0 1 1 1 1.0125 1 1 0 0 1 1 1 0.2125 _______________________________________________________________________________________ 5 Evaluates: MAX17021 MAX17021 Evaluation Kit Table 2. MAX17021 IMVP-6.5+ Output-Voltage VID DAC Codes (continued) D6 D5 D4 D3 D2 D1 D0 OUTPUT VOLTAGE (V) D6 D5 D4 D3 D2 D1 D0 OUTPUT VOLTAGE (V) 0 1 0 1 0 0 0 1.0000 1 1 0 1 0 0 0 0.2000 0 1 0 1 0 0 1 0.9875 1 1 0 1 0 0 1 0.1875 0 1 0 1 0 1 0 0.9750 1 1 0 1 0 1 0 0.1750 0 1 0 1 0 1 1 0.9625 1 1 0 1 0 1 1 0.1625 0 1 0 1 1 0 0 0.9500 1 1 0 1 1 0 0 0.1500 0 1 0 1 1 0 1 0.9375 1 1 0 1 1 0 1 0.1375 0 1 0 1 1 1 0 0.9250 1 1 0 1 1 1 0 0.1250 0 1 0 1 1 1 1 0.9125 1 1 0 1 1 1 1 0.1125 0 1 1 0 0 0 0 0.9000 1 1 1 0 0 0 0 0.1000 0 1 1 0 0 0 1 0.8875 1 1 1 0 0 0 1 0.0875 0 1 1 0 0 1 0 0.8750 1 1 1 0 0 1 0 0.0750 0 1 1 0 0 1 1 0.8625 1 1 1 0 0 1 1 0.0625 0 1 1 0 1 0 0 0.8500 1 1 1 0 1 0 0 0.0500 0 1 1 0 1 0 1 0.8375 1 1 1 0 1 0 1 0.0375 0 1 1 0 1 1 0 0.8250 1 1 1 0 1 1 0 0.0250 0 1 1 0 1 1 1 0.8125 1 1 1 0 1 1 1 0.0125 0 1 1 1 0 0 0 0.8000 1 1 1 1 0 0 0 0 0 1 1 1 0 0 1 0.7875 1 1 1 1 0 0 1 0 0 1 1 1 0 1 0 0.7750 1 1 1 1 0 1 0 0 0 1 1 1 0 1 1 0.7625 1 1 1 1 0 1 1 0 0 1 1 1 1 0 0 0.7500 1 1 1 1 1 0 0 0 0 1 1 1 1 0 1 0.7375 1 1 1 1 1 0 1 0 0 1 1 1 1 1 0 0.7250 1 1 1 1 1 1 0 0 0 1 1 1 1 1 1 0.7125 1 1 1 1 1 1 1 0 2) Switch SW1. When SW1 positions are off, the MAX17021’s D0–D6 inputs are at logic 1 (connected to VDD). When SW1 positions are on, D0–D6 inputs are at logic 0 (connected to GND). The output voltage can be changed during operation by activating SW1 on and off. As shipped, the EV kit is configured with SW1 positions set for 1.050V output (Table 2). Refer to the MAX17021 IC data sheet for more information. input (FBAC), so the resistance between FBAC and VOUT (R17) determines the voltage-positioning gain. Resistor R17 (4.32kΩ) provides a -2.1mV/A voltage-positioning slope at the output when all phases are active. Remote output and ground sensing eliminate any additional PCB voltage drops. Dynamic Output-Voltage Transition Experiment Reduced Power-Dissipation Voltage Positioning This MAX17021 EV kit is set to transition the output voltage at 12.6mV/µs. The speed of the transition is altered by scaling resistors R2 and R3. The MAX17021 includes a transconductance amplifier for adding gain to the voltage-positioning sense path. The amplifier’s input is generated by summing the currentsense inputs, which differentially sense the voltage across the inductor’s DCR. The transconductance amplifier’s output connects to the voltage-positioned feedback During the voltage transition, watch the inductor current by looking at the current-sense inputs with a differential scope probe. Observe the low, well-controlled inductor current that accompanies the voltage transition. Slew-rate control during shutdown and startup results in well-controlled currents in to and out of the battery (input source). 6 _______________________________________________________________________________________ MAX17021 Evaluation Kit Load-Transient Experiment One interesting experiment is to subject the output to large, fast load transients and observe the output with an oscilloscope. Accurate measurement of output ripple and load-transient response invariably requires that ground clip leads be completely avoided and the probe removed to expose the GND shield, so the probe can be directly grounded with as short a wire as possible to the board. Otherwise, EMI and noise pickup corrupt the waveforms. Most benchtop electronic loads intended for powersupply testing lack the ability to subject the DC-DC converter to ultra-fast load transients. Emulating the supply current (di/dt) at the IMVP-6.5+ VCORE pins requires at least 500A/µs load transients. An easy method for generating such an abusive load transient is to install a power MOSFET at the N7 location and install resistor R20 between 5mΩ and 10mΩ to monitor the transient current. Then drive its gate (TP1) with a strong pulse generator at a low-duty cycle (< 5%) to minimize heat stress in the MOSFET. Vary the high-level output voltage of the pulse generator to vary the load current. To determine the load current, you might expect to insert a meter in the load path, but this method is prohibited here by the need for low resistance and inductance in the path of the dummy-load MOSFET. To determine how much load current a particular pulsegenerator amplitude is causing, observe the current through inductor L1. In the buck topology, the load current is approximately equal to the average value of the inductor current. Note: The CPU socket is based on the Montevina platform pin configuration. Switch SW2 Settings Shutdown SW2 (1, 10) When SHDN goes low (SW2 (1, 10) = on), the MAX17021 enters low-power shutdown mode. PWRGD is pulled low immediately and the output voltage ramps down at 1/8 the slew rate set by R2 and R3 (71.1kΩ). When the controller reaches the 0V target, the drivers are disabled (DL1 and DL2 driven low), the reference is turned off, and the IC supply currents drop to 1µA (max). When a fault condition activates the shutdown sequence (output undervoltage lockout or thermal shut- Table 3. Shutdown Mode (SHDN) SHDN PIN SW2 (1, 10) MAX17021 OUTPUT Off* Connected to VDD Output enabled—VOUT is selected by VID DAC code (D0–D6) settings On Connected to GND Shutdown mode, V OUT = 0V *Default position. Table 4. DPRSLPVR, PSI DPRSLPVR SW2 (2, 9) PSI SW2 (3, 8) POWER LEVEL On (VDD) X Low current Off (GND) On (GND) Intermediate Off (GND)* Off (VDD)* Full OPERATING MODE 1-phase pulse-skipping mode 1-phase forced-PWM mode Normal operation—all phases are active, forced-PWM mode *Default position. X = Don’t care. Table 5. DPRSTP SW2 (5, 6) DPRSTP PIN Off Connected to VDD 1/4 of nominal slew rate is set by R2 and R3 if DPRSLPVR is also high On* Connected to GND Nominal slew rate MAX17021 *Default position. _______________________________________________________________________________________ 7 Evaluates: MAX17021 There are two methods to create an output-voltage transition. Select D0–D6 (SW1). Then either manually change the SW1 settings to a new VID code setting (Table 2), or disable all SW1 settings and drive the VID0–VID6 PCB test points externally to the desired code settings. Evaluates: MAX17021 MAX17021 Evaluation Kit down), the protection circuitry sets the fault latch to prevent the controller from restarting. To clear the fault latch and reactivate the MAX17021, toggle SHDN or cycle VDD power. DPRSLPVR SW2 (2, 9), PSI SW2 (3, 8) DPRSLPVR and PSI together determine the operating mode, as shown in Table 4. The MAX17021 will be forced into full-phase pulse-skipping mode during startup and while in boot mode, and forced into full-phase PWM mode during the transition from boot mode to VID mode and during soft-shutdown. DPRSTP, SW2 (5, 6) This 1V logic input signal together with the DPRSLPVR signal selects between the nominal and “slow” (quarter of nominal rate) slew rates. When DPRSTP and DPRSLPVR are forced high, the slew rate is reduced to a quarter of the nominal slew rate. PGDIN, SW2 (4, 7) PGDIN indicates the power status of other system rails and is used for power-supply sequencing. After powerup to the boot voltage, the output voltage remains at VBOOT, CLKEN remains high, and PWRGD remains low as long as the PGDIN stays low. When PGDIN is pulled high, the output transitions to selected VID voltage, and CLKEN is pulled low. If the system pulls PGDIN low during normal operation, the MAX17021 immediately drives CLKEN high, pulls PWRGD low, and slews the output to the boot voltage (using 2-phase pulse-skipping mode). The controller remains at the boot voltage until PGDIN goes high again, SHDN is toggled, or the VDD is cycled. Table 6. PGDIN SW2 (4, 7) PGDIN PIN MAX17021 OUTPUT Off Connected to GND VOUT remains at the boot voltage. CLKEN remains high, and PWRGD remains low. On* Connected to VDD VOUT transitions to selected VID voltage, and CLKEN is pulled low. *Default position. 8 _______________________________________________________________________________________ MAX17021 Evaluation Kit Evaluates: MAX17021 Figure 1a. MAX17021 EV Kit Schematic (Sheet 1 of 2) _______________________________________________________________________________________ 9 Evaluates: MAX17021 MAX17021 Evaluation Kit Figure 1b. MAX17021 EV Kit Schematic (Sheet 2 of 2) 10 ______________________________________________________________________________________ MAX17021 Evaluation Kit Evaluates: MAX17021 Figure 2. MAX17021 EV Kit Component Placement Guide— Component Side Figure 3. MAX17021 EV Kit PCB Layout—Component Side ______________________________________________________________________________________ 11 Evaluates: MAX17021 MAX17021 Evaluation Kit Figure 4. MAX17021 EV Kit PCB Layout—Internal Layer 2 (VBATT/PGND Plane) 12 Figure 5. MAX17021 EV Kit PCB Layout—Internal Layer 3 (Signal Layer) ______________________________________________________________________________________ MAX17021 Evaluation Kit Evaluates: MAX17021 Figure 6. MAX17021 EV Kit PCB Layout—Internal Layer 4 (PGND Layer) Figure 7. MAX17021 EV Kit PCB Layout —Internal Layer 5 (AGND/PGND Layer) ______________________________________________________________________________________ 13 Evaluates: MAX17021 MAX17021 Evaluation Kit Figure 8. MAX17021 EV Kit PCB Layout—Internal Layer 6 (Signal Layer) 14 Figure 9. MAX17021 EV Kit PCB Layout—Internal Layer 7 (PGND Layer) ______________________________________________________________________________________ MAX17021 Evaluation Kit Evaluates: MAX17021 Figure 10. MAX17021 EV Kit PCB Layout—Solder Side Figure 11. MAX17021 EV Kit Component Placement Guide— Solder Side Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 15 © 2009 Maxim Integrated Products SPRINGER Maxim is a registered trademark of Maxim Integrated Products, Inc.