EVALUATION KIT AVAILABLE
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
General Description
Benefits and Features
The IC offers a broad range of programmable features
through either the PMBus or a capacitor and resistor
connected to a dedicated programming pin. Using this
feature, the operation can be optimized for a specific
application, reducing the component count and/or setting
appropriate trade-offs between the regulator’s performance
and system cost. Ease of programming enables using the
same design for multiple applications.
●● Optimized Component Performance and Efficiency
with Reduced Design-In Time
• PMBus-Compliant Interface for Telemetry and
Power Management
• Voltage, Current, and Temperature Reporting
through the Digital Bus
The MAX20734 is a fully integrated, highly efficient switching regulator with PMBus™ for applications operating from
4.5V to 16V and requiring up to 40A (max) load. This
single-chip regulator provides extremely compact, highefficiency power-delivery solutions with high-precision
output voltages and excellent transient response for
networking, datacom, and telecom equipment.
The IC includes protection and telemetry features. Positive
and negative cycle-by-cycle overcurrent protection and
overtemperature protection ensure a rugged design.
Input undervoltage lockout shuts down the device to
prevent operation when the input voltage is out of
specification. A status pin provides an output signal to
show that the output voltage is within range and the
system is regulating.
●● High Power Density and Low Component Count
• Overall Solution Size 509mm2 Including Inductor
and Output Capacitors
• 90.7% Peak Efficiency with VDDH = 12V and VOUT
= 1V
• Fast Transient Response: Supports Up to 300A/μs
Load-Step Transients
●● Increased Power-Supply Reliability with System and
IC Self-Protection Features
• Differential Remote Sense with Open-Circuit
Detection
• Hiccup Overcurrent Protection
• Programmable Thermal Shutdown
Typical System Efficiency vs.
Load Current (VDDH = 12V)
Applications
100
Communications Equipment
Networking Equipment
Servers and Storage Equipment
Point-of-Load Voltage Regulators
µP Chipsets
Memory VDDQ
I/O
DESCRIPTION
CURRENT
INPUT
RATING* VOLTAGE
95
90
85
EFFICIENCY (%)
●●
●●
●●
●●
●●
●●
●●
75
VOUT
Vout
= 5V= 5V
70
VOUT
= 3.3V
Vout
= 3.3V
65
VOUT
= 1.8V
Vout
= 1.8V
OUTPUT
VOLTAGE
60
VOUT
Vout
= 1V= 1V
50
Electrical rating
40A
4.5V to 16V
0.6V to 5.5V
Thermal rating,
TA = 55°C, 200LFM
35A
12V
1V
Thermal rating,
TA = 85°C, 0LFM
22A
12V
1V
*For specific operating conditions, refer to the SOA curves in
the Typical Operating Characteristics section.
19-8585; Rev 0; 1/17
80
VOUT
= 1.2V
Vout
= 1.2V
VOUT
= 0.8V
Vout
= 0.8V
55
VOUT
= 0.65V
Vout
= 0.65V
0
5
10
15
20
25
30
35
IOUT (A)
Order Information appears at end of data sheet.
PMBus is a trademark of SMIF, Inc.
40
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Absolute Maximum Ratings
Input Pin Voltage (VDDH) (Note 1).........................-0.3V to +18V
VCC ..........................................................................-0.3V to +2V
STAT, OE, CLK, DATA, and
SMALERT Pin Voltages........................................-0.3V to +4V
PGMA, PGMB, VSENSE+ and
VSENSE- Pin Voltages..........................................-0.3V to +2V
Switching Node Voltage (VX) DC...........................-0.3V to +18V
Switching Node Voltage (VX) 25ns (Note 2)...........-10V to +23V
(BST - VX) Pin Differential....................................-0.3V to +2.5V
Junction Temperature (TJ)................................................+150°C
Storage Temperature Range............................. -65°C to +150°C
Peak Reflow Temperature Lead-Free.............................. +260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Operating Ratings
Input Voltage (VDDH)................................................. 4.5V to 16V
Junction Temperature (TJ)................................. -40°C to +125°C
Maximum Average Input Current (VDDH_MAX) (Note 3)..........6A
Maximum Average Output Current (IMAX).............................40A
Peak Output Current (IPK)......................................................90A
Package Information
PACKAGE TYPE: 15 FCQFN
Package Code
P154A9F+1
Outline Number
21-100027
Land Pattern Number
90-100025
THERMAL RESISTANCE
Junction to Ambient (θJA)
(Note 4; Still Air, No Heatsink)
12°C/W
Junction to Case (θJC)
0.42°C/W
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”,
“#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing
pertains to the package regardless of RoHS status.
Note 1: As measured at the VDDH pin referenced to GND pin immediately adjacent using a high-frequency scope probe with ILOAD
at IMAX. A high-frequency input bypass capacitor must be located less than 60 mils from the VDDH pin per our design
guidelines.
Note 2: The 25ns rating is the allowable voltage on the VX node in excess of the -0.3V to +18V DC ratings. The VX voltage may
exceed the DC rating in either the positive or negative direction for up to 25ns per cycle.
Note 3: See the Average Input Current Limit section.
Note 4: Data taken using Maxim’s evaluation kit (MAX20734EVKIT#). The PCB has four layers of 2oz copper.
www.maximintegrated.com
Maxim Integrated │ 2
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Electrical Characteristics
(Circuit of Figure 6, VDDH = 4.5V to 16V, TA = +25°C, unless otherwise noted. Typical values are at TA = +25°C. All devices 100%
tested at TA = +25°C. Limits over temperature guaranteed by design.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
16
V
5.5
V
SUPPLY VOLTAGE
Supply-Voltage Range
OUTPUT VOLTAGE (Note 5)
Output-Voltage Range
VDDH
TJ = -40°C to +125°C
4.5
VOUT
(Note 6)
0.6
1
Default is 1mV/μs; other values are set
through PMBus; measured at VSENSE+/pins
Programmable VOUT Slew Rates
2
VREF
0.6484
VBOOT Values
VREF Tolerance
mV/μs
4
Selected by C_SELA (Note 7)
0.8984
V
1.0
VREF
VREF = 0.6484V, 0.8984V, and 1.0V
(Notes 6, 8),
referred to VSENSE+/- pins
See Table 8 for accuracy vs. VREF
(Note 7)
Programmable VREF Range
-1.0
+1.0
%
0.6016
1.0
V
FEEDBACK LOOP
Integrator Recovery Time Constant
Gain (see the Control Loop Stability
section for details)
tREC
RGAIN
Gain Accuracy
20
Selected by R_SELB or
PMBus (Notes 6, 7, 8, 9)
(Notes 6, 8, 9)
μs
0.8
1.6
mV/A
3.2
-20
+20
%
SWITCHING FREQUENCY
400
Switching Frequency
fSW
500
400kHz/600kHz/800kHz selected by
C_SEL_B; other values are set through
PMBus (Note 7)
600
kHz
700
800
900
Switching Frequency Accuracy
(Notes 6, 8, 9)
-20
+20
%
INPUT PROTECTION
Rising VDDH UVLO Threshold
Falling VDDH UVLO Threshold
Hysteresis
www.maximintegrated.com
VDDH
UVLO
(Note 6)
4.25
3.7
3.9
350
4.47
V
mV
Maxim Integrated │ 3
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Electrical Characteristics (continued)
(Circuit of Figure 6, VDDH = 4.5V to 16V, TA = +25°C, unless otherwise noted. Typical values are at TA = +25°C. All devices 100%
tested at TA = +25°C. Limits over temperature guaranteed by design.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
9.5
13
16.5
%
OUTPUT-VOLTAGE PROTECTION (OVP)
Overvoltage-Protection, Rising
Threshold
OVP
Relative to programmed VOUT
OVP Deglitch Filter Time
8
Power-Good Protection, Falling
Threshold
Power-Good Protection Rising
Threshold
Relative to programmed VOUT
PWRGD
µs
6
9
12
%
3
6
9
%
Power-Good Deglitch Filter Time
8
µs
OVERCURRENT PROTECTION (OCP)
Selected by
R_SELB or
PMBus
(Notes 6, 7, 8, 9)
Positive OCP Inception
Threshold (Inductor Valley Current)
OCP
Negative OCP Inception
Threshold (Inductor Valley Current)
Selected by R_
SELB or PMBus
Hysteresis
OCP Setting 0
16.3
21
26.1
OCP Setting 1
20.8
27
33.0
OCP Setting 2
24.6
32
39.9
OCP Setting 3
30.6
38
45.5
OCP Setting 0
-28
OCP Setting 1
-33
OCP Setting 2
-39
OCP Setting 3
-44
Hysteresis applies only to positive OCP
A
A
15
%
OVERTEMPERATURE PROTECTION (OTP)
OTP Inception Threshold
OTP
Default is 150, 130 is set through PMBus
(Notes 7, 8, 9)
120
130
140
140
150
160
Hysteresis
°C
10
OE MAXIMUM VOLTAGE
OE Maximum Voltage
Rising Threshold
Hysteresis
OE
Full VCC supply range; measured at the
OE pin (Note 6)
VDDH 2.5
0.83
0.97
V
0.2
OE Pin Input Resistance
200
OE Deglitch Filter Time
0.9
(Note 9)
275
0.9
350
kΩ
2.2
µs
STARTUP TIMING
Enable Time from OE Rise to Start
of BST Charge
tOE
After tINIT
16
µs
0.75
Soft-Start Ramp Time
tSS
BST Charging Time
tBST
3 or 1.5 can be bet by R_SELA; any
value can be set by PMBus (Note 7)
1.5
3
ms
6
www.maximintegrated.com
8
µs
Maxim Integrated │ 4
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Electrical Characteristics (continued)
(Circuit of Figure 6, VDDH = 4.5V to 16V, TA = +25°C, unless otherwise noted. Typical values are at TA = +25°C. All devices 100%
tested at TA = +25°C. Limits over temperature guaranteed by design.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
3.6
V
STAT PIN
Allowable Pullup Voltage
Status Output Low
VOHSTAT
VOLSTAT
ISTAT = 2.5mA
0.4
ISTAT = 0.2mA, 0V < VCC < UVLO and
0V < VDDH < UVLO (Note 6)
0.65
ISTAT = 1.3mA, 0V < VCC < UVLO and
0V < VDDH < UVLO (Note 6)
0.75
Status Output High Leakage Current
ISTAT
STAT pulled up to 3.3V through 20kΩ
(Note 6)
Time from VOUT Ramp Completion
to STAT Pin Released
tSTAT
STAT output low to high, default is 125;
2000 can be set through PMBus (Note 7)
7
125
V
µA
µs
2000
PGMA AND PGMB PINS (see Tables 2–5)
Allowable R_SEL Resistor Range
12 resistor values detected
R_SEL Resistor Required Accuracy
EIA standard resistor values only
Allowable C_SEL Capacitor Range
3 options (0pF, 220pF, or 1000pF)
C_SEL Capacitor Required Accuracy
Use X7R or better
Allowable External Capacitance
Load and stray capacitance in addition
to C_SELA/B
1.78
162
±1
0
kΩ
%
1000
±20
pF
%
20
pF
16
V
PMBus TELEMETRY
Reading Range
4.5
Reading Update Interval
Reading Averaging Interval
Reading Error
VDDH
Readback
TA = -40°C to TJ = +125°C
(Notes 8, 9, 10, 11)
VSENSE
Readback
TA = -40°C to TJ = +125°C
(Notes 8, 9, 10, 11)
Reading Resolution
www.maximintegrated.com
ms
1
ms
+25
0
Reading Update Interval
IOUT
Readback
TA = -40°C to TJ = +125°C
(Notes 8, 9, 10, 11)
V
5
1.95
Reading Range
%
mV
1.25
-25
Reading Resolution
Reading Error
+3
0
Reading Update Interval
Reading Averaging Interval
ms
28
Reading Range
Referred to SENSE Pins (VOUT may
be scaled by divider in feedback)
ms
1
-3
Reading Resolution
Reading Averaging Interval
5
mV
mV
25
A
5
ms
1
ms
±3
A
0.07
A
Maxim Integrated │ 5
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Electrical Characteristics (continued)
(Circuit of Figure 6, VDDH = 4.5V to 16V, TA = +25°C, unless otherwise noted. Typical values are at TA = +25°C. All devices 100%
tested at TA = +25°C. Limits over temperature guaranteed by design.)
PARAMETER
SYMBOL
CONDITIONS
Reading Range
Reading Update Interval
Reading Averaging Interval
Reading Error
MIN
TYP
-40
Temperature
Readback
(Notes 6, 8, 9)
Reading Resolution
MAX
UNITS
+125
°C
5
ms
1
ms
±8
°C
0.52
°C
PMBus PINS (CLK, DATA, SMALERT)
Input Rising Threshold
Input Falling Threshold
Hysteresis
Output Low Voltage
PMBus Clock Frequency
SYSTEM SPECIFICATIONS (Note 10)
Line Regulation
Load Regulation (Static)
Efficiency (VDDH = 12V,
VOUT = 1V)
VT_RISE
VT_FALL
VHYS
VOL
0.83
0.9
0.97
V
0.62
0.7
0.79
V
0.2
Sinking 4mA
fPM_CLK
VOUT
η
±0.2
IOUT = 0 - IMAX
±0.7
Peak
90.7
Full load (40A)
84.3
V
0.4
V
400
kHz
%
%
Note 5: For proper regulation, it is required that VDDH > (VOUT + 2V). If VOUT is set > (UVLO - 2V), the IC may come out of UVLO,
but regulation is not guaranteed while VDDH is below (VOUT + 2V). To avoid this condition, OE can be held low until VDDH >
(VOUT + 2V).
Note 6: Denotes specifications that apply over the temperature range of TJ = -40 to +125°C.
Note 7: Denotes parameters that are programmable.
Note 8: Min/Max limits are ≥ 4σ about the mean.
Note 9: Guaranteed by design; not production tested.
Note 10: These specifications refer to the operation of the system and are based on the circuit shown in the reference schematic.
Tolerance of external components may affect these parameters. System performance numbers are measured using the
Maxim evaluation board for this product with BOM, as shown on the MAX20734 EV kit data sheet. If a different PCB layout
and different external components are used, these values may change.
Note 11: A -40°C test condition is specified at a TA test condition, instead of TJ, to allow for self-heating.
www.maximintegrated.com
Maxim Integrated │ 6
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Typical Operating Characteristics
(Unless otherwise stated: Tested on the MAX20734EVKIT# EV kit with component values per Table 7, VDDH = 12V, VOUT = 1V,
fSW = 400kHz, TA = 25°C, Still Air, and No Heatsink.)
STARTUP RESPONSE
TRANSIENT RESPONSE
toc01
toc02
VX (20V/div)
VOUT (20mV/div)
STAT(2V/div)
OE (2V/div)
VOUT (200mV/div)
TIME: 50µs/div
CONDITIONS: IOUT = 20A to 30A STEP at 1A/µs
TIME: 500µs/div
TYPICAL VOUT RIPPLE
SYSTEM EFFICIENCY vs. OUTPUT LOAD
toc03
100
toc04
95
90
85
VX (10V/div)
EFFICIENCY (%)
VOUT (20mV/div)
80
75
VOUT
Vout
= 5V= 5V
Vout
= 3.3V
VOUT
= 3.3V
70
VOUT
= 1.8V
Vout
= 1.8V
Vout
= 1.2V
VOUT
= 1.2V
65
60
Vout
= 1V= 1V
VOUT
Vout
= 0.8V
VOUT
= 0.8V
55
TIME: 5µs/div
CONDITIONS: IOUT = 40A
www.maximintegrated.com
50
Vout
= 0.65V
VOUT
= 0.65V
0
5
10
15
20
25
IOUT (A)
30
35
40
Maxim Integrated │ 7
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Typical Operating Characteristics (continued)
(Unless otherwise stated: Tested on the MAX20734EVKIT# EV kit with component values per Table 7, VDDH = 12V, VOUT = 1V,
fSW = 400kHz, TA = 25°C, Still Air, and No Heatsink.)
JUNCTION TEMPERATURE vs.
SYSTEM POWER DISSIPATION
LOAD REGULATION
toc05
0.4
VOUT = 5.5V
5.5V
VOUT = 3.3V
3.3V
100
VOUT = 1.8V
1.8V
0.2
JUNCTION TEMPERATURE (°C)
LOAD REGULATION (%)
0.3
1VVOUT = 1V
VOUT = 0.65V
.65V
0.1
0.0
-0.1
-0.2
-0.3
-0.4
5
10
15
20
25
30
35
SLOPE = 12°C/W
80
60
40
20
0
0
40
0
1
SYSTEM POWER DISSIPATION
35
Vout
= 1.8V
VOUT
= 1.8V
Vout
= 1.2V
VOUT
= 1.2V
6
Vout
= 0.65V
VOUT
= 0.65V
4
6
7
toc08
25
Vout=5.0V
VOUT = 5.0V
20
15
3
10
2
5
1
0
0
5
Vout=0.8V
VOUT = 0.8V
Vout=1.2V
VOUT = 1.2V
Vout=3.3V
VOUT = 3.3V
30
Vout
= 1V= 1V
VOUT
Vout
= 0.8V
VOUT
= 0.8V
5
4
40
IOUT (A)
SYSTEM POWER DISSIPATION (W)
45
VOUT
Vout
= 5V= 5V
Vout
= 3.3V
VOUT
= 3.3V
7
3
SAFE OPERATING AREA (SOA)
toc07
8
2
SYSTEM POWER DISSIPATION (W)
IOUT (A)
9
toc06
120
0
5
10
15
20
IOUT (A)
www.maximintegrated.com
25
30
35
40
30
40
50
60
70
80
90
100
TA (°C)
CONDITIONS: 400LFM
CURVE INDICATES TJ = 125°C, IOUT = IMAX, or IVDDH = IVDDH_MAX,
WHICHEVER HAPPENS FIRST
Maxim Integrated │ 8
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Typical Operating Characteristics (continued)
(Unless otherwise stated: Tested on the MAX20734EVKIT# EV kit with component values per Table 7, VDDH = 12V, VOUT = 1V,
fSW = 400kHz, TA = 25°C, Still Air, and No Heatsink.)
SAFE OPERATING AREA (SOA)
SAFE OPERATING AREA (SOA)
toc09
45
45
40
40
35
25
Vout=5.0V
VOUT = 5.0V
20
20
15
10
10
5
5
30
40
0
80
90
100
60
70
TA (°C)
CONDITIONS: 200LFM
CURVE INDICATES TJ = 125°C, IOUT = IMAX, or IVDDH = IVDDH_MAX,
WHICHEVER HAPPENS FIRST
50
SYSTEM EFFICIENCY vs.
OUTPUT LOAD (VDDH = 5V)
100
80
90
100
60
70
TA (°C)
CONDITIONS: STILL AIR / NO HEATSINK
CURVE INDICATES TJ = 125°C, IOUT = IMAX, or IVDDH = IVDDH_MAX,
WHICHEVER HAPPENS FIRST
40
SYSTEM POWER DISSIPATION (W)
85
80
75
70
Vout
= 1.8V
VOUT
= 1.8V
Vout
= 1.2V
VOUT
= 1.2V
Vout
= 1V= 1V
VOUT
Vout
= 0.8V
VOUT
= 0.8V
Vout
= 0.65V
VOUT
= 0.65V
65
60
55
0
5
10
www.maximintegrated.com
15
20
IOUT (A)
25
30
toc12
Vout
= 1.8V
VOUT
= 1.8V
Vout
= 1.2V
VOUT
= 1.2V
Vout
= 1V
VOUT
= 1V
5
Vout
= 0.8V
VOUT
= 0.8V
Vout
= 0.65V
VOUT
= 0.65V
4
3
2
1
0
35
50
7
6
90
50
30
SYSTEM POWER DISSIPATION (VDDH = 5V)
toc11
95
EFFICIENCY (%)
25
15
0
VOUT = 5.0V
Vout=5.0V
30
IOUT (A)
30
IOUT (A)
35
Vout=0.8V
VOUT = 0.8V
Vout=1.2V
VOUT = 1.2V
Vout=3.3V
VOUT = 3.3V
toc10
Vout=0.8V
VOUT = 0.8V
Vout=1.2V
VOUT = 1.2V
Vout=3.3V
VOUT = 3.3V
0
5
10
15
20
25
30
35
IOUT (A)
Maxim Integrated │ 9
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Typical Operating Characteristics (continued)
(Unless otherwise stated: Tested on the MAX20734EVKIT# EV kit with component values per Table 7, VDDH = 12V, VOUT = 1V,
fSW = 400kHz, TA = 25°C, Still Air, and No Heatsink.)
SAFE OPERATING AREA (SOA) (VDDH = 5V)
40
35
35
30
30
25
25
IOUT (A)
IOUT (A)
SAFE OPERATING AREA (SOA) (VDDH = 5V)
toc13
40
20
15
10
5
0
30
40
20
15
Vout=0.8V
VOUT = 0.8V
Vout=1.0V
VOUT = 1.0V
VOUT = 1.2V
Vout=1.2V
Vout=0.8V
VOUT = 0.8V
Vout=1.0V
VOUT = 1.0V
VOUT = 1.2V
Vout=1.2V
10
5
50
60
70
80
90
100
TA (°C)
CONDITIONS: 400LFM
CURVE INDICATES TJ = 125°C, IOUT = IMAX, or IVDDH = IVDDH_MAX,
WHICHEVER HAPPENS FIRST
toc14
0
30
40
50
60
70
80
90
100
TA (°C)
CONDITIONS: 200LFM
CURVE INDICATES TJ = 125°C, IOUT = IMAX, or IVDDH = IVDDH_MAX,
WHICHEVER HAPPENS FIRST
SAFE OPERATING AREA (SOA) (VDDH = 5V)
toc15
40
35
30
IOUT (A)
25
20
15
Vout=0.8V
VOUT = 0.8V
Vout=1.0V
VOUT = 1.0V
VOUT = 1.2V
Vout=1.2V
10
5
0
60
70
80
90
100
TA (°C)
CONDITIONS: STILL AIR / NO HEATSINK
CURVE INDICATES TJ = 125°C, IOUT = IMAX, or IVDDH = IVDDH_MAX,
WHICHEVER HAPPENS FIRST
www.maximintegrated.com
30
40
50
Maxim Integrated │ 10
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
PGMB
DATA
STAT
Pin Configuration
15
14
13
VSENSE+
1
12
CLK
VSENSE-
2
11
AGND
SMALERT
3
10
VCC
PGMA
4
9
OE
VDDH
5
8
BST
7
VX
GND
6
(TOP VIEW)
www.maximintegrated.com
Maxim Integrated │ 11
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Pin Description
PIN
NAME
FUNCTION
1
VSENSE+
Remote-Sense Positive Node. Connect this node to VOUT at the load. A resistive voltage-divider
can be used to regulate the output above the reference voltage.
2
VSENSE-
Remote-Sense Negative Node. Connect this node to ground at the load using a Kelvin connection.
3
SMALERT
4
PGMA
Program Node. Connect this node to ground through a programming resistor and capacitor.
5
VDDH
Power Input Voltage. The high-side MOSFET switch is connected to this node. See the Input
Capacitor Selection section for decoupling requirements.
6
GND
Power Ground Node. The low-side MOSFET switch is connected to this node.
7
VX
Power Switching Node. Connect this node to the inductor.
8
BST
Bootstrap for High-Side Switch. Connect a 0.22μF ceramic capacitor between BST and VX.
9
OE
Output Enable Node. This node is used to enable the regulator and has a precise
threshold to allow sequencing of multiple regulators. There is an internal 275kΩ (typ) pulldown on
this node.
10
VCC
Analog/Gate-Drive Supply for the IC from Internal 1.85V (typ) LDO. This node must be connected
to three 10µF X5R or better decoupling capacitors with very short, wide traces. VCC can be
connected to 20kΩ pullups for STAT and OE, as shown in Figure 6. Do not connect VCC to other
external loads. Do not overdrive VCC from an external source.
11
AGND
SMALERT Pin
Analog/Signal Ground. See the PCB Layout section for layout information.
12
CLK
PMBus Clock
13
STAT
Open-Drain Power-Good/Fault-Status Indication. Connect a pullup resistor to 1.8V or 3.3V.
14
DATA
PMBus Data
15
PGMB
Program Node. Connect this node to ground through a programming resistor and capacitor.
www.maximintegrated.com
Maxim Integrated │ 12
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Block Diagram
VCC
tON
TIMER
STAT
LDO
VDDH
BST
R
OE
S
DIGITAL
CONTROL
POWER
SWITCHING
Q
VX
PGMA
CURRENT
SENSE
OCP
PGMB
GND
CLK
PMBus
INTERFACE
DATA
PWM
ERROR
AMP
VSENSE+
SMALERT
VCC
TELEMETRY
VCC
VCC
CURRENT DAC
VSENSE-
AGND
Operation
Control Architecture
The MAX20734 provides an extremely compact, highefficiency regulator solution with minimal external
components and circuit design required. The monolithic
solution includes the top and bottom power switches,
gate drives, precision DAC reference, PWM controller,
fault protections, and PMBus interface (see the Block
Diagram). An external bootstrap capacitor is used to
provide the drive voltage for the top switch. Other external
components include the input and output filter capacitors,
buck inductor, and a few resistors and capacitors to set
the operating mode.
The IC implements an advanced valley current-mode
control algorithm that supports all multi-layer ceramic chip (MLCC) output capacitors and fast transient
response. In steady state, it operates at a fixed
switching frequency. When loading transients, the
switching frequency speeds up to minimize the output voltage undershoot. Likewise, when unloading
transients, the switching frequency slows down to
minimize the output voltage overshoot.
www.maximintegrated.com
REFERENCE VOLTAGE AND SOFT-START
The switching frequency can be set to 400kHz, 600kHz,
or 800kHz through C_SELB and can be overridden
through PMBus to 400kHz, 500kHz, 600kHz, 700kHz,
800kHz, or 900kHz.
Voltage regulation is achieved by modulating the low-side
on-time, comparing the difference between the feedback
and reference voltages with the low-side current-sense
signal using Maxim’s proprietary integrated current-sense
technology. Once the PWM modulator forces a low-to-high
transition, the high-side switch is enabled for a fixed time,
after which the low-side switch is turned on again. An error
amplifier with an integrator is used to maintain zero-droop
operation. The integrator has a transient recovery time
constant of 20μs (typ).
During regulation, the differential voltage between the
VSENSE+ and VSENSE- pins tracks the reference voltage,
which is set by the DAC and can be set from 0.6016V
to 1V. The sense pins can be connected to the output
voltage through a voltage-divider so VOUT can be higher
than 1V.
The switching frequency is determined by the high-side
on-time, as shown in Equation 1.
Maxim Integrated │ 13
MAX20734
Equation 1:
Integrated, Step-Down Switching
Regulator with PMBus
completion of the soft-start ramp time plus the userprogrammable STAT blanking time (tSTAT) of 125μs or
2ms. If OE is pulled low, the IC shuts down.
V
f SW =
× OUT
t H_ON VDDH
1
Alternatively, the IC can be enabled by sending a PMBus
Operate command. This raises the internal Operation
signal, which is OR’d with the OE pin to create an
internal OE signal. Therefore, when either the OE pin or the
internal Operate signal go high, startup is initiated, but it
takes both to be low to shut the part down.
where:
fSW = Switching frequency (MHz)
tH_ON = On-period for high-side switch (μs)
VOUT = Output voltage (V)
VDDH = Input voltage (V)
The tH_ON high-side on-time is controlled by the IC to be
proportional to the duty cycle so that the resulting switching
frequency is independent of supply voltage and output voltage.
Equation 2:
V
t H_ON ∝ OUT
VDDH
The tH_ON pulse width is clamped to a minimum of 50ns
(after tSS) and a maximum of 2µs to prevent any unexpected
operation during extreme VOUT conditions.
Voltage-Regulator Enable and Turn-On
Sequencing
The startup timing is shown in Figure 1. After VDDH is
applied, the IC goes through an initialization time (tINIT)
that takes up to 308μs. After initialization, OE is read.
Once OE is high for more than the 16μs OE filter time
(tOE), BST charging starts and is performed for 8μs (tBST),
and then the soft-start ramp begins. The soft-start ramp
time (tSS) can be 0.75ms, 1.5ms, 3ms, or 6ms depending on the user’s programmed value. VOUT ramps up
linearly during the soft-start ramp time. If there are no faults,
the STAT pin is released from being held low after the
Soft-Start Control
The initial output voltage behavior is determined by a
linear ramp of the internal reference voltage from zero to
the final value (tSS in Figure 1). The ramp time (tSS) is
programmable from 0.75ms to 6ms.
If the regulator is enabled when the output voltage has a
residual voltage, the system will not regulate until the reference voltage ramps above this residual value. In this case,
the tOE (OE valid to onset of regulation) specification is
extended by the time required for the desired voltage startup ramp to reach the actual residual output voltage, but the
time to reach the steady-state output voltage is unchanged.
If the residual voltage is higher than the set output
voltage, neither the high-side or low-side switch is turned
on by the end of tSS. Under these conditions, switching
begins after tSS.
The MAX20734 exhibits a non-linearity during startup.
This behavior is normal and does not have an adverse
effect on system operation. With the circuit of Figure 6,
the typical nonlinearity is 55mV with RGAIN = 0.8mV/A or
1.6mV/A, 330mV with RGAIN = 3.2mV/A, and 480mV with
RGAIN = 6.4mV/A. The nonlinearity gets proportionately
smaller as COUT increases.
tINIT
VCC
tOE
SHUTDOWN
OE or OPERATE
VOUT
tBST
tSS
STAT
tSTAT
tINIT : Initialization, 308µs.
tOE : OE enable filter time, 16µs. If OE enabled earlier than tINIT completion, it is ignored until tINIT completes.
tBST : BST charging time, 8µs.
tSS : Soft-start time per user selection, 0.75ms – 6ms.
tSTAT : STAT blanking time, 2ms or 125µs through user selection.
Figure 1. Startup Timing
www.maximintegrated.com
Maxim Integrated │ 14
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Remote Output-Voltage Sensing
To ensure the most accurate sensing of the output voltage, a differential voltage-sense topology is used, with a
negative remote-sense pin provided. Point-of-load (PoL)
sensing compensates for voltage drops between the output of the regulator and its load and provides the highest
regulation accuracy. The voltage-sensing circuit features
excellent common-mode rejection to further improve load
voltage regulation.
Protection and Status Operation
Output-Voltage Protection
The feedback voltage is continuously monitored for both
undervoltage and overvoltage conditions. The typical
fault-detection threshold is 13% above and 9% below
the reference voltage (see the Electrical Characteristics
table). If the output voltage falls below the power-good
protection (PWRGD) threshold beyond the filter time, the
STAT output goes low, but the system continues to operate, attempting to maintain regulation.
If the output voltage rises above the overvoltage protection (OVP) threshold beyond the filter time, the STAT pin
is lowered and the system shuts down until the output
voltage falls within the valid range.
the OCP threshold current, as shown in Figure 2. In this
situation, turn-on of the high-side switch is prevented
until the current falls below the threshold level. Since the
inductor valley current is the controlled parameter, the
average current delivered during positive current clamping remains a function of several system-level parameters. Note that IOCP has hysteresis and the value drops
down to IOCP2 once it has been triggered (see Figure 2).
Undervoltage Lockout (UVLO)
The regulator internally monitors VDDH with a UVLO
circuit. When the input supply voltage is below the UVLO
threshold, the regulator stops switching, and the STAT
pin is driven low. For UVLO levels, see the Electrical
Characteristics table.
Overtemperature Protection (OTP)
The OTP-level default is 150°C and can be set to 130°C
over PMBus. If the die temperature reaches the OTP level
during operation, the regulator is disabled and the STAT pin
is driven low. Overtemperature is a nonlatching fault, with
the hysteresis shown in the Electrical Characteristics table.
Table 1. Summary of Fault Actions
FAULT
Current Limiting and Short-Circuit Protection
The regulator’s valley current-mode control architecture
provides inherent current limiting and short-circuit protection. The bottom switch’s instantaneous current is monitored using integrated current sensing and is controlled
on a cycle-by-cycle basis within the control block.
Current clamping occurs when the minimum instantaneous (“valley”) low-side switch current level exceeds
ACTION
Power Good
(Output Undervoltage)
STAT LOW
Output OVP
STAT LOW, Shutdown and Restart
Overtemperature
STAT LOW, Shutdown and Restart
Supply Fault (VDDH_
UVLO, VCC_UVLO)
STAT LOW, Shutdown and Restart
BST Fault
STAT LOW, Shutdown and Restart
IOCP(AVG)
IOCP
IOCP2
IOCP(AVG) = IOCP2 +
I
L
1
2
( VDDH − VOUT ) x
tH_ON
LOUT
where:
IOCP2 = IOCP - Hysteresis
Figure 2. Inductor Current During Current Limiting
www.maximintegrated.com
Maxim Integrated │ 15
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Regulator Status (STAT)
PGMA and PGMB Pin Functionality
The STAT pin is low while the regulator is disabled and
goes high after the startup ramp is completed, plus the
programmed tSTAT blanking interval if the output voltage
is within the PWRGD/OVP regulation window. The STAT
pin is an open-drain output and is 3.3V tolerant. The pin
remains low when VDDH is not present.
The parasitic loading on the PGMA and PGMB pins must
be limited to less than 20pF and greater than 20mΩ to
avoid interfering with the R_SEL and C_SEL decoding.
The STAT signal provides an open-drain output
consistent with CMOS logic levels, which indicates
whether the regulator is functioning properly. An external
pullup resistor is required for connecting STAT to VCC or
another 1.8V or 3.3V supply.
The PGMA and PGMB pins are used to set up some of
the key programmable features of the regulator IC. A
resistor and capacitor are connected to the PGMA/B pins
and their values are read during power-up initialization
(e.g., power must be cycled to re-read the values).
Table 3. PGMA Pin C_SELA Capacitor
Values
The STAT pin is driven low when one or more of the
following conditions occurs:
NO.
C (pF) ±20%
● PWRGD fault (see the Output-Voltage Protection
section)
1
Open
2
220
0.8984
3
1000
1
● VSENSE- pin is left unconnected or shorted to VDDH
● Die temperature exceeds the temperature shutdown
threshold shown in the Electrical Characteristics table
VBOOT (V)
0.6484
Table 4. PGMB Pin R_SELB Values
NO.
R (kΩ) ±1%
RGAIN (mΩ)
OCP SETTING*
1
1.78
0.8
0
● Supply voltage drops below the UVLO threshold
2
2.67
0.8
1
● Fault detected on the BST node, such as shorted or
open bootstrap capacitor
3
4.02
0.8
2
4
6.04
0.8
3
The ensuing startup follows the same timing shown in
Figure 1.
5
9.09
3.2
0
6
13.3
3.2
1
7
20
3.2
2
8
30.9
3.2
3
● OVP circuit detects that the output voltage is above the
tolerance limit
Table 2. PGMA Pin R_SELA Values
NO.
R (kΩ)
±1%
SOFT-START
TIME (mS)
PMBus SLAVE
ADDRESS (1010_xxx)
1
1.78
3
1010 000b
2
2.67
3
1010 001b
3
4.02
3
1010 010b
4
6.04
3
1010 011b
5
9.09
3
1010 100b
6
13.3
3
1010 101b
7
20
3
1010 110b
8
30.9
3
1010 111b
9
46.4
1.5
1010 000b
NO.
C (pF) ±20%
10
71.5
1.5
1010 001b
1
Open
11
107
1.5
1010 010b
2
220
600
12
162
1.5
1010 011b
3
1000
800
www.maximintegrated.com
9
46.4
1.6
0
10
71.5
1.6
1
11
107
1.6
2
12
162
1.6
3
*See the Electrical Characteristics table for values.
Table 5. PGMB Pin C_SELB Capacitor
Values
fSW FEQUENCY (kHz)
400
Maxim Integrated │ 16
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
PMBus Commands
A summary of PMBus commands is shown in Table 6.
PMBus communication can be initiated as soon as VCC
is valid (after tINIT, Figure 1), regardless of the state of
the OE and STAT pins. For more information, refer to
AN6209: MAX20734 PMBus Application Note.
PMBus Telemetry
The IC provides input and output voltage, output current,
and junction-temperature telemetry. Output voltage is
measured at the VSENSE+/- pins. Therefore, if there is a
divider in the feedback, the measurement is scaled by the
divide ratio. For range and accuracy specifications, see
the Electrical Characteristics table. For data format, refer
to AN6209: MAX20734 PMBus Application Note.
Table 6. Summary of PMBus Commands
COMMAND NAME
TYPE*
NO. OF
DATA
BYTES
COMMAND
CODE
COMMAND NAME
TYPE*
NO. OF
DATA
BYTES
01h
OPERATION
RW
1
7Dh
STATUS_TEMPERATURE
RO
1
02h
ON_OFF_CONFIG
RO
1
7Eh
STATUS_CML
RO
1
03h
CLEAR_FAULTS
WO
0
80h
STATUS_MFR_SPECIFIC
RO
1
10h
WRITE_PROTECT
RW
1
88h
READ_VIN
RO
2
1Bh
PMBALERT_MASK
RW
2
8Bh
READ_VOUT
RO
2
20h
VOUT_MODE
RO
1
8Ch
READ_IOUT
RO
2
21h
VOUT_COMMAND
RW
2
8Dh
READ_TEMPERATURE_1
RO
2
24h
VOUT_MAX
RW
2
99h
MFR_ID
BLK
4
78h
STATUS_BYTE
RO
1
9Bh
MFR_REVISION
BLK
1
79h
STATUS_WORD
RO
2
D1h
MFR_VOUT_MIN
RW
2
7Ah
STATUS_VOUT
RO
1
D2h
MFR_DEVSET1
RW
2
7Bh
STATUS_IOUT
RO
1
7Ch
STATUS_INPUT
RO
1
COMMAND
CODE
www.maximintegrated.com
D3h
MFR_DEVSET2
RW
2
*RW = Read/Write, WO = Write Only, RO = Read Only, and
BLK = Block.
Maxim Integrated │ 17
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Reference Design
Equation 3:
A typical application schematic is shown in Figure 3, and
optimum component values for common output voltages
are shown in Table 7.
where:
Output-Voltage Setting
VOUT = Output voltage
I VDDH =
If an output voltage not listed in Table 7 is required,
calculate new values for RFB1 and RFB2 (as discussed
below) and use the other circuit values of the closest
output voltage in Table 7, or calculate them as shown below.
VOUT × I OUT
VDDH × η
IOUT = Output current
VDDH = Input voltage
η = Efficiency (refer to the Typical Operating Characteristics
section)
Average Input Current Limit
The input current of VDDH is given by Equation 3. VOUT,
IOUT, and VDDH should be properly chosen so that the
average input current does not exceed 6A (IVDDH_MAX).
VDDH
CVCC
CIN
VCC
1.8V or 3.3V
STAT
OE
CLK
DATA
SMALERT
CLK
DATA
SMALERT
AGND
C_SELA
R_SELB
CBST
BST
LOUT
VOUT
VX
PGMA
PGMB
R_SELA
VDDH
MAX20734
RSTAT
STAT
OE
1.8V or 3.3V
COMPLIANT I/O
U1
RFB1
VSENSE+
VSENSECOUT
RFB2
GND
C_SELB
Figure 3. Typical Application Circuit
Table 7. Reference Design Component Values
VOUT
(V)
RFB1
(kΩ)
RFB2 R_SELA C_SELA R_SELB C_SELB
(kΩ)
(pF)
(kΩ)
(pF)
(kΩ)
0.6484
1
Open
1.78
Open
107
0.8
1.37
5.9
1.78
Open
fSW LOUT
(kHz) (nH)
RGAIN
(mΩ)
VREF
(V)
Open
1.6
0.6484
400
170
12 x 100μF + 1 x 22μF
71.5
Open
1.6
0.6484
400
170
10 x 100μF + 1 x 22μF
COUT
1
1.87
3.48
1.78
Open
71.5
Open
1.6
0.6484
400
170
9 x 100μF + 1 x 22μF
1.2
1.74
2.05
1.78
Open
71.5
Open
1.6
0.6484
400
170
9 x 100μF + 1 x 22μF
1.8
3.09
1.74
1.78
Open
71.5
220
1.6
0.6484
600
170
9 x 100μF + 1 x 22μF
3.3
5.62
1.37
1.78
Open
162
220
1.6
0.6484
600
210
9 x 100μF + 1 x 22μF
5.0
7.15
1.07
1.78
Open
107
220
1.6
0.6484
600
210
9 x 100μF + 1 x 22μF
Note: For input caps, see the Input Capacitor Selection section.
www.maximintegrated.com
Maxim Integrated │ 18
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
The output voltage is set by the VREF DAC and divider
ratio of resistors RFB1 and RFB2 per Equation 4. The
IC regulates the VSENSE+ pin to the reference voltage
(VREF) set by the DAC. Upon power-up, the DAC voltage
initializes to one of the user-selectable VBOOT voltages.
Using PMBus, the DAC can also be set to any voltage from
0.6016V to 1V with 3.9mV resolution, as shown in Table 8.
The divider resistors are chosen to give the correct output
voltage and to have an approximate parallel resistance of
RPAR = 1kΩ for best common-mode rejection of the error
amplifier. In applications requiring less than 10mV peak-topeak output voltage ripple, setting a lower DAC reference
voltage such as 0.6484V or less is recommended because
the part will have less DAC voltage noise.
The divider resistors are then given by Equation 5.
Equation 4:
VOUT = Output voltage
Equation 5:
R PAR
R
=
FB1 VOUT ×
VREF
R PAR
R=
FB2 R FB1 ×
R
-R
FB1 PAR
where:
RFB1 = Top divider resistor
RFB2 = Bottom divider resistor
RPAR = Desired parallel resistance of RFB1 and RFB2
VREF = Reference voltage = 0.6016V to 1V (set by DAC)
R
VOUT
= VREF × 1 + FB1
R
FB2
where VREF = 0.6016V to 1V (set by DAC).
Table 8. Voltage vs. PMBus VOUT_COMMAND
VOUT
COMMAND
[9:0]
(decimal)
VOLTAGE ACCURACY
(V)
(+/-)
VOUT
COMMAND
[9:0]
(decimal)
VOLTAGE ACCURACY
(V)
(+/-)
VOUT
COMMAND
[9:0]
(decimal)
VOLTAGE ACCURACY
(V)
(+/-)
307
0.6016
1.2%
325
0.6367
1.1%
343
0.6719
1.0%
308
0.6016
1.2%
326
0.6367
1.1%
344
0.6719
1.0%
309
0.6055
1.2%
327
0.6406
1.0%
345
0.6758
1.0%
310
0.6055
1.2%
328
0.6406
1.0%
346
0.6758
1.0%
311
0.6094
1.2%
329
0.6445
1.0%
347
0.6797
1.0%
312
0.6094
1.2%
330
0.6445
1.0%
348
0.6797
1.0%
313
0.6133
1.2%
331
0.6484
1.0%
349
0.6836
1.0%
314
0.6133
1.2%
332
0.6484
1.0%
350
0.6836
1.0%
315
0.6172
1.1%
333
0.6523
1.0%
351
0.6875
1.0%
316
0.6172
1.1%
334
0.6523
1.0%
352
0.6875
1.0%
317
0.6211
1.1%
335
0.6563
1.0%
353
0.6914
1.0%
318
0.6211
1.1%
336
0.6563
1.0%
354
0.6914
1.0%
319
0.6250
1.1%
337
0.6602
1.0%
355
0.6953
1.0%
320
0.6250
1.1%
338
0.6602
1.0%
356
0.6953
1.0%
321
0.6289
1.1%
339
0.6641
1.0%
357
0.6992
1.0%
322
0.6289
1.1%
340
0.6641
1.0%
358
0.6992
1.0%
323
0.6328
1.1%
341
0.6680
1.0%
359
0.7031
1.0%
324
0.6328
1.1%
342
0.6680
1.0%
360
0.7031
1.0%
www.maximintegrated.com
Maxim Integrated │ 19
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Table 8. Voltage vs. PMBus VOUT_COMMAND (continued)
VOUT
COMMAND
[9:0]
(decimal)
VOLTAGE ACCURACY
(V)
(+/-)
VOUT
COMMAND
[9:0]
(decimal)
VOLTAGE ACCURACY
(V)
(+/-)
VOUT
COMMAND
[9:0]
(decimal)
VOLTAGE ACCURACY
(V)
(+/-)
361
0.7070
1.0%
396
0.7734
1.0%
431
0.8438
1.0%
362
0.7070
1.0%
397
0.7773
1.0%
432
0.8438
1.0%
363
0.7109
1.0%
398
0.7773
1.0%
433
0.8477
1.0%
364
0.7109
1.0%
399
0.7813
1.0%
434
0.8477
1.0%
365
0.7148
1.0%
400
0.7813
1.0%
435
0.8516
1.0%
366
0.7148
1.0%
401
0.7852
1.0%
436
0.8516
1.0%
367
0.7188
1.0%
402
0.7852
1.0%
437
0.8555
1.0%
368
0.7188
1.0%
403
0.7891
1.0%
438
0.8555
1.0%
369
0.7227
1.0%
404
0.7891
1.0%
439
0.8594
1.0%
370
0.7227
1.0%
405
0.7930
1.0%
440
0.8594
1.0%
371
0.7266
1.0%
406
0.7930
1.0%
441
0.8633
1.0%
372
0.7266
1.0%
407
0.7969
1.0%
442
0.8633
1.0%
373
0.7305
1.0%
408
0.7969
1.0%
443
0.8672
1.0%
374
0.7305
1.0%
409
0.8008
1.0%
444
0.8672
1.0%
375
0.7344
1.0%
410
0.8008
1.0%
445
0.8711
1.0%
376
0.7344
1.0%
411
0.8047
1.0%
446
0.8711
1.0%
377
0.7383
1.0%
412
0.8047
1.0%
447
0.8750
1.0%
378
0.7383
1.0%
413
0.8086
1.0%
448
0.8750
1.0%
379
0.7422
1.0%
414
0.8086
1.0%
449
0.8789
1.0%
380
0.7422
1.0%
415
0.8125
1.0%
450
0.8789
1.0%
381
0.7461
1.0%
416
0.8125
1.0%
451
0.8828
1.0%
382
0.7461
1.0%
417
0.8164
1.0%
452
0.8828
1.0%
383
0.7500
1.0%
418
0.8164
1.0%
453
0.8867
1.0%
384
0.7500
1.0%
419
0.8203
1.0%
454
0.8867
1.0%
385
0.7539
1.0%
420
0.8203
1.0%
455
0.8906
1.0%
386
0.7539
1.0%
421
0.8242
1.0%
456
0.8906
1.0%
387
0.7578
1.0%
422
0.8242
1.0%
457
0.8945
1.0%
388
0.7578
1.0%
423
0.8281
1.0%
458
0.8945
1.0%
389
0.7617
1.0%
424
0.8281
1.0%
459
0.8984
1.0%
390
0.7617
1.0%
425
0.8320
1.0%
460
0.8984
1.0%
391
0.7656
1.0%
426
0.8320
1.0%
461
0.9023
1.0%
392
0.7656
1.0%
427
0.8359
1.0%
462
0.9023
1.0%
393
0.7695
1.0%
428
0.8359
1.0%
463
0.9063
1.0%
394
0.7695
1.0%
429
0.8398
1.0%
464
0.9063
1.0%
395
0.7734
1.0%
430
0.8398
1.0%
465
0.9102
1.0%
www.maximintegrated.com
Maxim Integrated │ 20
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Table 8. Voltage vs. PMBus VOUT_COMMAND (continued)
VOUT
COMMAND
[9:0]
(decimal)
VOLTAGE ACCURACY
(V)
(+/-)
VOUT
COMMAND
[9:0]
(decimal)
VOLTAGE ACCURACY
(V)
(+/-)
VOUT
COMMAND
[9:0]
(decimal)
VOLTAGE ACCURACY
(V)
(+/-)
466
0.9102
1.0%
482
0.9414
1.0%
498
0.9727
1.0%
467
0.9141
1.0%
483
0.9453
1.0%
499
0.9766
1.0%
468
0.9141
484
0.9453
1.0%
500
0.9766
1.0%
469
0.9180
1.0%
1.0%
0.9492
1.0%
501
0.9805
1.0%
0.9180
1.0%
485
470
486
0.9492
1.0%
502
0.9805
1.0%
471
0.9219
487
0.9531
1.0%
503
0.9844
1.0%
472
0.9219
488
0.9531
1.0%
504
0.9844
1.0%
473
0.9258
489
0.9570
1.0%
505
0.9883
1.0%
474
0.9258
490
0.9570
1.0%
506
0.9883
1.0%
475
0.9297
491
0.9609
1.0%
507
0.9922
1.0%
476
0.9297
492
0.9609
1.0%
508
0.9922
1.0%
477
0.9336
493
0.9648
1.0%
509
0.9961
1.0%
478
0.9336
494
0.9648
1.0%
510
0.9961
1.0%
479
0.9375
1.0%
495
0.9688
1.0%
511
1.0000
1.0%
480
0.9375
1.0%
496
0.9688
1.0%
512
1.0000
1.0%
481
0.9414
1.0%
497
0.9727
1.0%
—
—
—
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
Notes: The repeated voltage values in the table are due to ignoring the LSB in hardware. The available VBOOT values are highlighted in gray. Voltages shown are referenced to the sense pins. Actual VOUT can be scaled by a voltage-divider in the
feedback.
www.maximintegrated.com
Maxim Integrated │ 21
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Control-Loop Stability
The IC uses valley current-mode control which is stabilized by selecting appropriate values of COUT and RGAIN.
No compensation network is required. For stability, the
loop bandwidth (BW) should be 100kHz or less. Consider
the case of using MLCC output capacitors that have
nearly ideal impedance characteristics in the frequency
range of interest with negligible ESR and ESL. The loop
bandwidth can be approximated by breaking the loop into
gain terms as outlined below.
1) The IC’s valley current-mode control scheme has an
effective transconductance gain of 1/RGAIN.
2) For MLCC capacitors, the output capacitors contribute
an impedance gain of 1/(2 x π x COUT x f).
3) The feedback-divider contributes an attenuation of
KDIV = RFB2/(RFB1 + RFB2).
4) An inherent high-frequency pole located at 150kHz.
When the BW is 100kHz or less, the high-frequency pole
can be ignored and the approximate loop gain and BW
are given by Equation 6.
Equation 6:
LOOP_GAIN (f) =
BW =
OR
BW =
K DIV
2 × π × R GAIN × C OUT × f
K DIV
2 × π × R GAIN × C OUT
Integrator
The IC has an integrator included in its error
amplifier, which was ignored in the above equations for
simplicity. The integrator only adds gain at low frequencies,
so it does not really effect the loop BW calculation. The
purpose of the integrator is to improve load regulation. The
integrator adds a factor of (1/tREC + s)/s to the loop gain.
Step Response
RGAIN_EFF is important because it determines the smallsignal transient response of the regulator. When a
load step is applied that does not exceed the slew-rate
capability of the inductor current, the regulator responds
linearly and VOUT temporarily changes by the amount of
VOUT_ERROR (see Equation 7).
Equation 7:
VOUT_ERROR = I STEP × R GAIN_EFF
The integrator causes VOUT to recover to the nominal
value with a time constant of tREC = 20μs. The regulator
can be modeled to a first-order by the averaged smallsignal equivalent circuit shown in Figure 4. Here, VEQ is
an ideal voltage source, REQ is an equivalent lossless
resistance created by the control-loop action, and LEQ is
an equivalent inductance. Note that LEQ is not the same
as the actual LOUT inductor that has been absorbed into
the model. COUT is the actual output capacitance.
tREC RGAIN_EFF
1
2 × π × R GAIN_EFF × C OUT
LEQ
where:
RGAIN_EFF = RGAIN/KDIV
For stability, RGAIN and COUT should be chosen so that
BW < 100kHz.
RGAIN_EFF
The available RGAIN settings are shown in Table 4. When
choosing which RGAIN setting to use, one should consider
that while higher RGAIN allows the loop to be stabilized with
less COUT, less COUT generally results in higher ripple and
larger transient overshoot and undershoot, so there needs
to be a balance.
REQ
VOUT
COUT
VOUT
VEQ
GND
Figure 4. Averaged Small-Signal Equivalent Circuit of Regulator
Note: The large-signal transient response is approximately the
larger between the VOUT_ERROR and the unloading transient.
www.maximintegrated.com
Maxim Integrated │ 22
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Output-Capacitor ESR
In the above control-loop discussion, the case of MLCC
output capacitors has been considered. Another case
worth mentioning is the use of output capacitors with
more significant ESR. This can be considered as long
as the capacitors are rated to handle the inductor current
ripple and expected surge currents. Thus far, it has been
assumed that COUT is comprised of MLCCs and the net
ESR is negligible compared to RGAIN/KDIV. If the net ESR
of the COUT bank is not negligible compared to RGAIN/
KDIV, the inductor current ripple is effectively sensed by the
ESR and adds to the RGAIN_EFF, as shown in Equation 8.
Equation 8:
R GAIN_EFF =
R GAIN
+ ESR
K DIV
The capacitor’s ESR also introduces a zero into the loop
gain. The inherent high-frequency pole helps to compensate this zero. For a more in-depth view of the effect of
circuit values on regulator performance, the Maxim Simplis
model and MAX20734 evaluation kit can be used. It is
recommended to simulate and/or test regulator
performance when using values other than the
recommended component values.
The performance data shown in the Typical Operating
Characteristics section was taken using the MAX20734
evaluation kit and component values in Table 7. For most
applications, these are the optimum values to use. Table 9,
Table 10, and Table 11 show suitable part numbers for
input and output capacitors and the inductor.
Table 9. Recommended Inductors
COMPANY
VALUE
(nH)
I SAT
(A)
R DC
(mΩ)
FOOTPRINT
(mm)
HEIGHT
(mm)
PART
NUMBER
WEBSITE
Cooper
170
60
0.29
10.4 x 8.0
7.5
FP1007R3-R17-R
www.cooperindustries.com
Pulse
215
41
0.29
10.4 x 7.9
7.3
PA2607.211NL
www.pulseelectronics.com
Pulse
270
34
0.29
10.4 x 7.9
7.3
PA2607.271NL
www.pulseelectronics.com
Pulse
320
45
0.32
13.5 x 13.0
8.0
PA0513.321NLT
www.pulseelectronics.com
Pulse
440
30
0.32
13.5 x 13.0
8.0
PA0513.441NLT
www.pulseelectronics.com
Table 10. MLCC Input Capacitors
CASE SIZE
VALUE
(µF)
TEMPERATURE
RATING
VOLTAGE
RATING
T
(mm) (NOTE 1)
COMPANY
0603
1
X7S
X7R
16V
0.8
(Note 2)
Murata
TDK
GRM188C71C105KA12D
C1608X7R1C105K
0805
2.2
X7R
25V
16V
16V
1.25
1.25
1.25
Murata
TDK
AVX
GRM21BR71E225KA73L
C2012X7R1C225M
0805YC225MAT
0805
4.7
X7R
16V
1.25
Murata
GRM21BR71C475K
1206YC475MAT
GRM31CR71C475KA01L
PART NUMBER
1206
4.7
X7R
16V
1.65
AVX
Murata
1206
10
X7R
16V
1.65
Murata
TDK
AVX
GRM31CR71C106KAC7L
C3216X7R1C106M
1206YC106MAT
1210
10
X7R
16V
25V
2.0
2.5
Murata
TDK
GRM32DR71C106KA01L
C3225X7R1E106M
1210
22
X7R
16V
2.45
2.5
2.5
AVX
Murata
TDK
1210YC226MAT
GRM32ER71A476K
C3225X7R1C226M
Note 1: T indicates nominal thickness.
Note 2: Indicates capacitors with nominal thickness smaller than the minimum FCQFN package thickness.
www.maximintegrated.com
Maxim Integrated │ 23
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Table 11. Recommended Output Capacitors
COMPANY
VALUE
(µF)
PART NUMBER
TEMPERATURE
RATING
VOLTAGE
RATING
CASE
SIZE
Τ
(mm)
(Note 1)
WEBSITE
AVX Corp.
22
22
08054D226MAT2A
12066D226MAT2A
X5R
X5R
4V
6.3V
0805
1206
1.3
1.65
www.avxcorp.com
Murata
22
22
22
GRM21BR60J226ME39L
GRM31CR60J226KE19L
GRM32DR60J226KA01L
X5R
X5R
X5R
6.3V
6.3V
6.3V
0805
1206
1210
1.25
1.6
2.0
www.murata.co.jp
Panasonic
22
22
22
ECJ3YB0J226M
ECJHVB0J226M
ECJ3Y70J226M
X5R
X5R
X7R
6.3V
6.3V
6.3V
1206
1206
1206
1.6
0.85
1.65
www.panasonic.
com
Taiyo Yuden
22
22
22
AMK212BJ226MG
JMK316BJ226ML
JMK325BJ226MY
X5R
X5R
X5R
4V
6.3V
6.3V
0805
1206
1210
1.25
1.6
1.9
www.taiyo-yuden.
com
TDK Corp.
22
22
22
22
C2012X5R0J226M
C3216X5R0J226M
C3225X5R0J226M
C3216X6S0J226M
X5R
X5R
X5R
X6S
6.3V
6.3V
6.3V
6.3V
0805
1206
1210
1206
1.25
1.6
1.6
1.6
www.component.
tdk.com
Note 1: T indicates nominal thickness.
Inductor Selection
The output inductor has an important influence on the overall size, cost, and efficiency of the voltage regulator. Since
the inductor is typically one of the larger components in the
system, a minimum inductor value is particularly important
in space-constrained applications. Smaller inductor values
also permit faster transient response, reducing the amount
of output cap needed to maintain transient tolerances.
For any buck regulator, the maximum current slew rate
through the output inductor is given by Equation 9.
Equation 9:
dIL
VL
SlewRate
= =
dt L OUT
where:
IL = Inductor current
LOUT = Output inductance
VL = VDDH - VOUT during high-side FET conduction and
-VOUT during low-side FET conduction
Equation 9 shows that larger inductor values limit the
regulator’s ability to slew current through the output
inductor in response to step-load transients. Consequently,
more output capacitors are required to supply (or store)
sufficient charge to maintain regulation while the inductor
current ramps up to supply the load.
www.maximintegrated.com
In contrast, smaller inductor values increase the
regulator’s maximum achievable slew rate and decrease
the necessary capacitance, at the expense of higher
ripple current. The peak-to-peak ripple current is given by
Equation 10.
Equation 10:
I OUTRIPPLE =
t H_ON × (VDDH − VOUT )
L OUT
where:
tH_ON = High-side switch on-time (based on nominal
VOUT) (see Equation 1)
LOUT = Output inductance
VDDH = Input voltage
VOUT = Output voltage
From Equation 10, for the same switching frequency and
ripple current increases as L decreases. This increased
ripple current results in increased AC losses, larger peak
current, and for the same output capacitance, results in
increased output voltage ripple.
Maxim Integrated │ 24
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
IOUTRIPPLE should be set to 25% to 50% of the IC’s rated
output current. A suitable inductor value can then be found
by solving Equation 10 for inductance as in Equation 11
and Equation 12.
Equation 11:
L OUT =
VOUT (VDDH − VOUT )
VDDH × I OUTRIPPLE × f SW
Assuming IOUTRIPPLE = 0.5 x IOUT for a typical inductor
value, see Equation 12.
Equation 12:
LOUT =
VOUT ( VDDH − VOUT )
VDDH × ( 0.5 ×IOUT ) × fSW
For a 25A regulator running at 400kHz, with VDDH = 12V
and VOUT = 1V, Equation 13 shows the target value for
the inductor.
Equation 13:
LOUT =
1× (12 − 1)
12 × 0.5 × 25 × 400000
= 183nH
The saturation current rating of the inductor is another
important consideration. At current limit, the peak inductor
current is given in Equation 14.
Equation 14:
IPK = I OCP + I OUTRIPPLE
where:
IOCP = Overcurrent protection trip point (see the Electrical
Characteristics table and the Current Limiting and ShortCircuit Protection section)
IOUTRIPPLE = Peak-to-peak inductor current ripple, as
defined above
For proper OCP operation of the regulator, it is important
that IPK never exceeds the saturation current rating of
the inductor (ISAT). It is recommended that a margin of at
least 20% is included between IPK and ISAT, as shown in
Equation 15.
Equation 15:
I SAT > 1.2 × IPK
www.maximintegrated.com
Also, note that during a hard VOUT short circuit,
IOUTRIPPLE increases due to VOUT going to zero in
Equation 10.
Finally, the power dissipation of the inductor influences
the regulation efficiency. Losses in the inductor include
core loss, DC resistance loss, and AC resistance loss.
For the best efficiency, use inductors with core material
exhibiting low loss in the range of 0.5MHz to 2MHz, and
low-winding resistance.
Table 9 provides a summary of the recommended
inductor suppliers and part numbers.
Output Capacitor Selection
The minimum recommended output capacitance for
stability is described in the Control-Loop Stability section
and is normally implemented using several 100µF 1206 (or
similar) MLCCs. For low slew-rate transient loads, RGAIN_
EFF determines the VOUT_ERROR for a given load step per
the small-signal model, as discussed above. In this case,
COUT has no effect on the VOUT_ERROR.
However, in the event that the slew rate of the load transient greatly exceeds the slew rate of the inductor current,
the transient VOUT_ERROR may be larger than predicted
by the small-signal model. In this case, the VOUT loading
and unloading transients can be approximated by taking
the larger result between Equation 7 and Equation 16.
Equation 16:
I
LOUT × ISTEP + OUTRIPPLE
2
LOADINGTRANSIENT(V) =
2 × COUT × ( VDDH − VOUT )
2
I
LOUT × ISTEP + OUTRIPPLE
2
UNLOADINGTRANSIENT(V) =
2 × COUT × VOUT
+ ISTEP ×
2
tH _ ON
COUT
In order to meet an aggressive transient specification,
COUT may have to be increased and/or LOUT decreased;
however, note that decreasing LOUT results in larger
inductor ripple current; thus, decreased efficiency and
increased output ripple.
Maxim Integrated │ 25
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Output voltage ripple is another important consideration in the selection of output capacitors. For a buck
regulator operating in CCM, the total voltage ripple across
the output capacitor bank can be approximated as the
sum of three voltage waveforms: 1) the triangle wave
that results from multiplying the AC ripple current by the
ESR, 2) the square wave that results from multiplying the
ripple current slew rate by the ESL, and 3) the piecewise
quadratic waveform that results from charging/discharging
the output capacitor. Although the phasing of these three
components impacts the total output ripple, a common
approximation is to ignore the phasing and to find the
upper bound of the peak-to-peak ripple by summing all
three components, as shown in Equation 17.
the triangular AC ripple current at the output, the total RMS
current and power is given by Equation 18 and Equation 19.
Equation 17:
ESR = Equivalent series resistance of the entire output
capacitor bank
VDDH IOUTRIPPLE
VP
=
+
−P ESR (IOUTRIPPLE ) + ESL
LOUT 8 × fSW × COUT
where:
ESR = Equivalent series resistance at the output
IOUTRIPPLE = Peak-to-peak inductor current ripple
ESL = High-frequency equivalent series inductance at
output
VDDH = Input voltage
LOUT = Output inductance
fSW = Switching frequency
COUT = Output capacitance
In a typical MAX20734 application with a bank of
0805, X5R, 6.3V, 22µF output capacitors, these three
components are roughly equal.
The ESL effect of an output capacitor on output voltage
ripple cannot be easily estimated from the resonant frequency so the high-frequency (10MHz or above) impedance of that capacitor should be used instead. PCB traces
and vias in the VOUT/GND loop contribute additional
parasitic inductance.
The final considerations in the selection of output capacitors are ripple-current rating and power dissipation. Using
a conservative design approach, the output capacitors
should be designed to handle the maximum peak-topeak AC ripple current experienced in the worst-case
scenario. Because the recommended output capacitors
have extremely low ESR values, they are typically rated
well above the current and power stresses seen here. For
Equation 18:
I
IRMS _ COUT = OUTRIPPLE
12
where:
IOUTRIPPLE = Peak-to peak ripple current value
Equation 19:
=
PCOUT IRMS _ COUT 2 × ESR
where:
Input Capacitor Selection
The selection and placement of input capacitors are
important considerations. High-frequency input capacitors
serve to control switching noise. Bulk input capacitors are
designed to filter the pulsed DC current that is drawn by
the regulator. For the best performance, lowest cost, and
smallest size of the MAX20734 systems, MLCC capacitors with 1210 or smaller case sizes, capacitance values
of 47µF or smaller, 16V or 25V voltage ratings, and X5R
or better temperature characteristics are recommended
as bulk. The minimum recommended value of capacitance are 2 x 47µF (bulk) and 1.0µF + 0.1µF (high frequency). Smaller values of bulk capacitance can be used
in direct proportion to the maximum load current.
It is recommended to choose the main MLCC input
capacitance to control the peak-to-peak input-voltage
ripple to 2% to 3% of its DC value in accordance with
Equation 20.
Equation 20:
I
× VOUT × (VDDH − VOUT )
C IN = MAX
f SW × VDDH 2 × VINPP
(
)
where:
CIN = Input capacitance (MLCC)
IMAX = Maximum load current
VDDH = DC input voltage
VOUT = DC output voltage
fSW = Switching frequency
VINPP = Target peak-to-peak input-voltage ripple
www.maximintegrated.com
Maxim Integrated │ 26
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Because the bulk input capacitors must source the pulsed
DC input current of the regulator, the power dissipation
and ripple current rating for these capacitors are far more
important than that for the output capacitors. The RMS
current that the input capacitor must withstand can be
approximated using Equation 21.
Equation 21:
IRMS _ CIN =
ILOAD VOUT ( VDDH − VOUT )
VDDH
where:
ILOAD = Output DC load current
With an equivalent series resistance of the bulk input
capacitor bank (ESRCIN), the total power dissipation in
the input capacitors is given by Equation 22.
Equation 22:
=
PCIN IRMS _ CIN2 × ESRCIN
Resistor Selection and its Effect on DC
Output-Voltage Accuracy
RFB1 and RFB2 set the output voltage, as described in
Equation 4. The tolerance of these resistors affects the
accuracy of the set output voltage. Due to the form of
Equation 4, the effect is higher at higher output voltages.
Figure 5 shows the effect of 0.1% tolerance resistors over
a range of output voltages. For different tolerance resistors,
multiply the output voltage error by the resistors’ tolerances
divided by 0.1% (e.g., for 0.5% tolerance resistors, multiply the output error shown by 5). To obtain accuracy over
temperature, for a worst-case scenario, the temperature
coefficients multiplied by the temperature range should be
added to the tolerance (i.e., for 25ppm/°C resistors over
a 50°C excursion, add 0.125% to the 25°C tolerance).
The error due to the voltage feedback resistors’ tolerance
(RFB1 and RFB2) should be added to the output-voltage
tolerance due to the IC’s feedback-voltage accuracy
shown in the Electrical Characteristics table.
Voltage Margining
Voltage margining can be achieved by changing the
VOUT setting through PMBus. VOUT changes occur with
a default linear slew rate of 1V/ms. The slew rate can be
set to 1, 2, or 4mV/μs using the VRATE bits. Refer to the
AN6140: MAX20734 PMBus Application Note for details.
If a voltage-divider is present in the feedback loop, the
VOUT slew rate will be scaled accordingly.
0.180%
0.160%
0.140%
ERROR (%)
0.120%
0.100%
εVOUT = 2εR(VOUT - VREF)/VOUT
0.080%
0.060%
0.040%
0.020%
0.000%
1
1.5
2
2.5
3
3.5
4
4.5
5
VOUT/VREF RATIO
Figure 5. DC Accuracy Impact Showing Effect of 0.1% Tolerance for RFB1 and RFB2
www.maximintegrated.com
Maxim Integrated │ 27
MAX20734
PCB Layout Guidelines
PCB layout can dramatically affect the performance of the
regulator. A poorly designed board can degrade efficiency,
noise performance, and even control-loop stability. At higher
switching frequencies, layout issues are especially critical.
As a general guideline, the input capacitors and the
output inductor should be placed in close proximity to
the regulator IC, while the output capacitors should be
lumped together as close as possible to the load. Traces
to these components should be kept as short and wide
as possible to minimize parasitic inductance and resistance. Traces connecting the input capacitors and VDDH
(power input node) on the IC require particular attention
since they carry currents with the largest RMS values
and fastest slew rates. According to best practice, the
input capacitors should be placed as close as possible
to the input supply pins, with the smallest package highfrequency capacitor being the closest to the IC and no
more than 60 mils from the IC pins. Preferably, there
should be an uninterrupted ground plane located immediately underneath these high-frequency current paths, with
the ground plane located no more than 8 mils below the
top layer. By keeping the flow of this high-frequency AC
current localized to a tight loop at the regulator, electromagnetic interference (EMI) can be minimized.
Voltage-sense lines should be routed differentially directly
from the load points. The ground plane can be used as a
shield for these or other sensitive signals to protect them from
capacitive or magnetic coupling of high-frequency noise.
www.maximintegrated.com
Integrated, Step-Down Switching
Regulator with PMBus
For remote-sense applications where the load and
regulator IC are separated by a significant distance
or impedance, it is important to place the majority of
the output capacitors directly at the load. Ideally, for
system stability, all the output capacitors should be
placed as close as possible to the load. In remote-sense
applications, common-mode filtering is necessary to filter
high-frequency noise in the sense lines.
The following layout recommendations should be used for
optimal performance:
● It is essential to have a low-impedance and
uninterrupted ground plane under the IC and extended
out underneath the inductor and output capacitor bank.
● Multiple vias are recommended for all paths that carry
high currents (i.e., GND, VDDH, VX). Vias should be
placed close to the chip to create the shortest possible
current loops. Via placement must not obstruct the
flow of currents or mirror currents in the ground plane.
● A single via in close proximity to the chip should be
used to tie the top layer AGND trace to the second
layer ground plane, it must not be connected to the top
power ground area.
● The feedback-divider and compensation network
should be close to the IC to minimize the noise on the
IC side of the divider.
Gerber files with layout information and complete
reference designs can be obtained by contacting a Maxim
account representative.
Maxim Integrated │ 28
R1
1.78K
0402
C32
1000pF
0402
C4
DNS
0402
DNS = Do Not Stuff
Vboot = 0.6484V
PMBus Addr = 1010 000b
Soft Start Time = 3ms
SMALERT
DATA
CLK
OE
STAT
20K
R8 0402
PGMB
PGMA
C23
DNS
0402
C51
10uF
X5R
0402
Fsw = 400kHz
OCP = 38A Valley
Rgain = 1.6 m-ohms
R2
162K
0402
C9
10uF
X5R
0402
PGMB
PGMA
VX
BST
U1
VSENSE-
VSENSE+
MAX20734
SMALERT
DATA
CLK
OE
STAT
C36
10uF
X5R
0402
VDDH
VDDH
VCC
VCC
AGND
20K
GND
www.maximintegrated.com
R5 0402
C3
0.1uF
X7R
0402
SENSE-
SENSE+
VX
BST
C8
0.22uF
X7R
0402
C7
1uF
X7R
0603
Diff Pair
C5
47uF
X5R
1206
170nH
L1
C6
47uF
X5R
1206
C10
47uF
X5R
1206
VDDH
R9
3.48K
0402
R6
1.87K
0402
SENSE_VOUT
C11
47uF
X5R
1206
Diff Pair
INPUT SUPPLY
0 0402
0
R11
R4 0402
C24
0.01uF
0402
C21
22uF
0805
C12-20
9x100uf
1206
VOUT = 1V
VOUT
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Figure 6. Reference Schematic (VOUT = 1V, VDDH = 4.5V to 16V)
Maxim Integrated │ 29
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
MAX20734EPL+
-40°C to +125°C
15 FCQFN
MAX20734EPL+T
-40°C to +125°C
15 FCQFN
+Denotes a lead(Pb)-free/RoHS-compliant package.
T = Tape and reel.
www.maximintegrated.com
Maxim Integrated │ 30
MAX20734
Integrated, Step-Down Switching
Regulator with PMBus
Revision History
REVISION
NUMBER
REVISION
DATE
0
1/17
PAGES
CHANGED
DESCRIPTION
Initial release
—
For information on other Maxim Integrated products, visit Maxim Integrated’s website at www.maximintegrated.com.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits)
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
© 2017 Maxim Integrated Products, Inc. │ 31
工商网监
湘ICP备2023018690号
