MAX2120EVKIT+

Evaluates: MAX2120 MAX2120 Evaluation Kit General Description The MAX2120 evaluation kit (EV kit) simplifies the testing and evaluation of the IC direct-conversion tuner. The evaluation kit is fully assembled and tested at the factory. Standard 50Ω SMA and BNC connectors are included on the EV kit for the inputs and outputs to allow quick and easy evaluation on the test bench. This document provides a list of equipment required to evaluate the device, a straightforward test procedure to verify functionality, a description of the EV kit circuit, the circuit schematic, a component list for the kit, and artwork for each layer of the PCB. Features ●● Easy Evaluation of the MAX2120 ●● 50Ω RF Input SMA Connector ●● 50Ω Baseband Output BNC Connector ●● Single 3.3V ±5% Supply ●● I2C 2-Wire Serial Interface ●● All Critical Peripheral Components Included ●● Fully Assembled and Tested ●● PC Control Software (available at www.maximintegrated.com/evkitsoftware) Ordering Information PART TYPE MAX2120EVKIT+ EV Kit +Denotes lead(Pb)-free and RoHS compliant. Component List DESIGNATION QTY ADDR 0 Not installed, 3-pin (1 x 3) inline header, 0.01in centers Sullins PEC36SAAN BB_I_O/P, BB_Q_O/P 2 50Ω BNC PC mounts Amphenol 31-5329-52RFX 10 PC mini red test points Keystone 5000 BB_IN, BB_IP, BB_QN, BB_QP, CP_OUT, J12, J13, J17, REF_O/P, VGC DESCRIPTION 8 1000pF ±10% ceramic capacitors (0603) Murata GRM188R71H102K C7, C13, C19, C20, C75 5 0.1µF ±10% ceramic capacitors (0603) Murata GRM188R71C104K C8, C12, C25–C29 0 Not installed, capacitors C1–C6, C9, C14 19-2071; Rev 2; 11/14 DESIGNATION QTY DESCRIPTION C10, C11 2 0.047μF ±10% ceramic capacitors (0603) Murata GRM188R71C473K C15 1 0.033μF ±10% ceramic capacitor (0603) Murata GRM188R61A334K C16 1 0.022μF ±10% ceramic capacitor (0603) Murata GRM188R71H223K C17, C18 2 10μF ±10% tantalum capacitors (C Case) AVX TAJC016K016 C22 1 43.2Ω ±1% resistor (0603)* C23, C24, C71–C73 5 330pF ±5% ceramic capacitors (0603) Murata GRM1885C1H331J J6 1 DB25 right-angle male connector AMP 5747238-4 Evaluates: MAX2120 MAX2120 Evaluation Kit Component List (continued) DESIGNATION QTY JP_VCC, VCC_BB, VCC_DIG, VCC_LO, VCC_RF1, VCC_RF2, VCC_SYN, VCC_VCO 0 L1 1 DESCRIPTION DESIGNATION Not installed, 2-pin (1 x 2) inline headers, 0.01in centers Sullins PEC36SAAN 0 R3, R7, R15–R17, R21 6 0Ω ±5% resistors (0603)* R4, R5, R13, R24 4 1kΩ ±5% resistors (0603)* REF_INPUT 0 RF_INPUT 1 SMA edge-mount connector, round contact Emerson 142-0701-801 U1 1 DVBS tuner (28 TQFN-EP**) Maxim MAX2120CTI+ U2, U4 0 Not installed, single-supply op amps with R2R outputs Maxim MAX4453ESA U3 1 74LV07A hex buffer/driver OC TI SN74LV07ADR U5 0 Not installed, open I/O comparator Maxim MAX985 Y1 1 4MHz crystal Citizen America 300-8526-1-ND Digi-Key HCM49-4.000MABJ-UT 0 Not installed, shunts (JP_VCC, VCC_BB, VCC_DIG, VCC_LO, VCC_RF1, VCC_RF2, VCC_SYN, VCC_VCO) Shorting jumpers, 2 position Sullins SSC02SYAN Not installed, resistors R6 1 820Ω ±5% resistor (0603)* R8 1 86.6Ω ±1% resistor (0603)* R9–R11, R41, R42 5 100Ω ±1% resistors (0603)* R14, R43 2 5.1kΩ ±5% resistors (0603)* R23, R26 2 0.1µF ±10% ceramic capacitors (0603) Murata GRM188R71C104K R46, R47 2 2.7kΩ ±5% resistors (0603)* DESCRIPTION Not installed, SMA edge-mount connector, round contact Emerson 142-0701-801 33pF ±5% capacitor (0603) Murata GRM1885C1H330J R2, R12, R18–R20, R22, R25, R27–R33 QTY — — 1 PCB: MAX2112/20 EVALUATION KIT *Use lead-free parts only. **EP = Exposed pad. Component Suppliers SUPPLIER WEBSITE AMP/Tyco Electronics www.tycoelectronics.com Amphenol RF www.amphenolrf.com AVX Corp. www.avxcorp.com Digi-Key Corp. www.digikey.com Emerson Network Power www.emersonnetworkpower.com Keystone Electronics Corp. www.keyelco.com Murata Americas www.murataamericas.com Sullins Electronics Corp. www.sullinselectronics.com Texas instruments www.ti.com Note: Indicate that you are using the MAX2120 when contacting these component suppliers. www.maximintegrated.com Maxim Integrated │  2 MAX2120 Evaluation Kit Quick Start Test Equipment Required ● MAX2120 EV kit ●● Dual-output power supply capable of supplying up to 3.3V at > 160mA for VCC and 3V at > 50μA for VGC gain control voltage ● RF signal generator capable of delivering at least 0dBm of output power at frequencies up to 2.175GHz ● RF spectrum analyzer capable of covering the operating frequency range of the device ● PC laptop or tablet with Microsoft Windows XP®, Windows® 7, 8 operating system and a spare USB port ● USB-A male to USB-B male cable ● US keyboard ● Multichannel digital oscilloscope (optional) ● Network analyzer to measure return loss (optional) ● Ammeter to measure supply current (optional) Procedure The EV kit is fully assembled and factory tested. Follow the instructions in the Connections and Setup section for proper device evaluation. Measurement Considerations The EV kit includes on-board matching circuitry at the MAX2120 RF input to convert the 50Ω source to a 75Ω input. Note that the input power to the device must be adjusted to account for the -6dB power loss of the matching resistor network. Connections and Setup This section provides a step-by-step guide to testing the basic functionality of the EV kit in UHF mode. Caution: Do not turn on DC power or RF signal generators until all connections are completed. 1) Verify that all jumpers are in place. Evaluates: MAX2120 4) With its output disabled, set the RF signal generator to a 955MHz frequency at -69dBm to account for the 6dB resistive pad loss. When measuring noise figure, this 6dB must also be accounted for by subtracting 6dB from the measured noise figure, unless the pad has been removed. 5) Connect the output of the RF signal generator to the SMA connector labeled RF _INPUT on the evaluation board. 6) Connect the PC to the INTF3000 interface board using the USB-A male to USB-B male cable. On the INTF3000, place a jumper between pins 1-2 on JU1 (VBUS Pos). Connect the 25-pin connector of the INTF3000 (J4) directly to the 25-pin connector on the EV kit (J6). 7) Turn on the 3.3V VCC power supply, followed by the 3V gain-control power supply. The supply current from the 3.3V VCC supply should read approximately 100mA, and the supply current from the 3V VGC should read approximately 50μA. Be sure to adjust the power supply to account for any voltage drop across the ammeter. 8) Install and run the IC control software. Software is available for download on the Maxim website at www.maximintegrated.com/evkitsoftware. 9) Load the default register settings from the control software by clicking Edit: Load Defaults. Set ICP = 1 and BBG[3:0] = 1011. 10) Connect the output to a spectrum analyzer or an oscilloscope. 11) Enable the RF signal generator’s output. 12) Activate and set the power level of the RF generator to achieve 1VP-P at the baseband BNC connector outputs. 13) Check the I/Q outputs. 14) Observe the baseband output at 5MHz with 1VP-P. 2) With its output disabled, connect the DC power supply to VGC set to 0.5V (maximum gain). 3) With its output disabled, set the DC power supply to 3.3V. Connect the power supply to the VCC (through an ammeter if desired) and GND terminals on the EV kit. If available, set the current limit to 200mA. Windows and Windows XP are registered trademarks and registered service marks of Microsoft Corporation. www.maximintegrated.com Maxim Integrated │  3 MAX2120 Evaluation Kit Layout Considerations The EV kit can serve as a guide for PCB layout. Keep RF signal lines as short as possible to minimize losses and radiation. Use controlled impedance on all high-frequency traces. The exposed paddle must be soldered evenly to the board’s ground plane for proper operation. Use abundant vias beneath the exposed paddle for maximum heat dissipation. Use abundant ground vias between RF traces to minimize undesired coupling. www.maximintegrated.com Evaluates: MAX2120 To minimize coupling between different sections of the IC, the ideal power-supply layout is a star configuration, which has a large decoupling capacitor at the central VCC node. The VCC traces branch out from this node, with each trace going to separate VCC pins of the IC. Each VCC pin must have a bypass capacitor with a low impedance to ground at the frequency of interest. Do not share ground vias among multiple connections to the PCB ground plane. Maxim Integrated │  4 MAX2120 Evaluation Kit Evaluates: MAX2120 Figure 1. MAX2120 EV Kit Schematic www.maximintegrated.com Maxim Integrated │  5 MAX2120 Evaluation Kit Evaluates: MAX2120 Figure 2. MAX2120 EV Kit PCB Layout—Component Placement Guide www.maximintegrated.com Maxim Integrated │  6 MAX2120 Evaluation Kit Evaluates: MAX2120 Figure 3. MAX2120 EV Kit PCB Layout—Top www.maximintegrated.com Maxim Integrated │  7 MAX2120 Evaluation Kit Evaluates: MAX2120 Figure 4. MAX2120 EV Kit PCB Layout—Bottom www.maximintegrated.com Maxim Integrated │  8 MAX2120 Evaluation Kit Evaluates: MAX2120 Figure 5. MAX2120 EV Kit PCB Layout—Top Soldermask www.maximintegrated.com Maxim Integrated │  9 MAX2120 Evaluation Kit Evaluates: MAX2120 Figure 6. MAX2120 EV Kit PCB Layout—Bottom Soldermask www.maximintegrated.com Maxim Integrated │  10 Evaluates: MAX2120 MAX2120 Evaluation Kit Revision History REVISION REVISION NUMBER DATE DESCRIPTION 0 11/07 Initial release 1 5/10 Updated L1 in the Component List and Figure 1 2 11/14 Updated Quick Start section PAGES CHANGED — 2, 5 3 For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com. Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. © 2014 Maxim Integrated Products, Inc. │  11