Click here for production status of specific part numbers.
MAX3095/MAX3096
General Description
The MAX3095/MAX3096 are rugged, low-power, quad,
RS-422/RS-485 receivers with electrostatic discharge
(ESD) protection for use in harsh environments. All
receiver inputs are protected to ±15kV using IEC 10004-2 Air-Gap Discharge, ±8kV using IEC 1000-4-2 Contact
Discharge, and ±15kV using the Human Body Model.
The MAX3095 operates from a +5V supply, while the
MAX3096 operates from a +3.3V supply. Receiver
propagation delays are guaranteed to within ±8ns of a
predetermined value, thereby ensuring device-to-device
matching across production lots.
Complementary enable inputs can be used to place the
devices in a 1nA low-power shutdown mode in which the
receiver outputs are high impedance. When active, these
receivers have a fail-safe feature that guarantees a logichigh output if the input is open circuit. They also feature a
quarter-unit-load input impedance that allows 128 receivers
on a bus.
±15kV ESD-Protected, 10Mbps, 3V/5V,
Quad RS-422/RS-485 Receivers
Features
●● ESD Protection:
• ±15kV—IEC 1000-4-2, Air-Gap Discharge
• ±8kV—IEC 1000-4-2, Contact Discharge
• ±15kV—Human Body Model
●● Guaranteed Propagation-Delay Tolerance
Between All ICs:
• ±8ns (MAX3095)
• ±10ns (MAX3096)
●● Single +3V Operation (MAX3096)
Single +5V Operation (MAX3095)
●● 16-Pin QSOP (8-pin SO footprint)
●● 10Mbps Data Rate
●● Allow up to 128 Receivers on the Bus
●● 1nA Low-Power Shutdown Mode
●● 2.4mA Operating Supply Current
●● Pin-Compatible Upgrades to ’26LS32
The MAX3095/MAX3096 are pin-compatible, low-power
upgrades to the industry-standard ’26LS32. They are
available in a space-saving QSOP package.
Applications
●●
●●
●●
●●
Telecommunications Equipment
Rugged RS-422/RS-485/RS-423 Bus Receiver
Receivers for ESD-Sensitive Applications
Level Translators
Functional Diagram
VCC
G
MAX3095
MAX3096
G
A1
Y1
B1
A2
Y2
B2
A3
Y3
B3
A4
Y4
B4
GND
19-0498; Rev 4; 1/18
MAX3095/MAX3096
±15kV ESD-Protected, 10Mbps, 3V/5V,
Quad RS-422/RS-485 Receivers
Absolute Maximum Ratings
Supply Voltage (VCC)...............................................................7V
Control Input Voltage (G, G)..................... -0.3V to (VCC + 0.3V)
Receiver Input Voltage (A_, B_)...........................................±25V
Receiver Output Voltage (Y_)................... -0.3V to (VCC + 0.3V)
Continuous Power Dissipation (TA = +70°C)
16-Pin Plastic DIP (derate 10.5mW/°C above +70°C).... 762mW
16-Pin SO (derate 8.7mW/°C above +70°C)................696mW
16-Pin QSOP (derate 8.3mW/°C above +70°C)..........667mW
Operating Temperature Ranges
MAX309_C_ _.....................................................0°C to +70°C
MAX309_E_ _................................................. -40°C to +85°C
Storage Temperature Range............................. -65°C to +160°C
Lead Temperature (soldering, 10s).................................. +300°C
Maximum Junction Temperature......................................+150°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
DC Electrical Characteristics—MAX3095
(VCC = 5V ±5%, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
Receiver Differential Input
Threshold
SYMBOL
VTH
Receiver Input Hysteresis
Receiver Input Current (A_, B_)
CONDITIONS
-7V ≤ VCM ≤ 12V
VCM = 0V
IIN
VCC = 0V or 5.25V
Enable Input Current (G, G)
Enable Input High Voltage (G, G)
Enable Input Low Voltage (G, G)
MIN
TYP
-200
MAX
UNITS
200
mV
45
VIN = 12V
250
VIN = -7V
VIH
mV
-200
±1
2.0
µA
µA
V
VIL
0.8
V
Receiver Output High Voltage
VOH
IOUT = -4mA, VID = 200mV,
G = VCC or G = GND, Figure 1
Receiver Output Low Voltage
VOL
IOUT = 4mA, VID = -200mV,
G = VCC or G = GND, Figure 1
0.4
V
Three-State Current at Receiver
Output
IOZR
0 ≤ VOUT ≤ VCC, G = GND and G = VCC
±1
µA
Output Short-Circuit Current
IOSR
0 ≤ VOUT ≤ VCC, G = VCC or G = GND
Receiver Input Resistance
Supply Current
ESD Protection (Note 2)
www.maximintegrated.com
RIN
ICC
-7V ≤ VCM ≤ 12V
No load, G = VCC or G = GND
G = GND and G = VCC
VCC - 1.5
V
±7
±75
48
mA
kΩ
2.4
3.5
mA
0.001
10
µA
Human Body Model
±15
IEC 1000-4-2 (Air-Gap Discharge)
±15
IEC 1000-4-2 (Contact Discharge)
±8
kV
Maxim Integrated │ 2
MAX3095/MAX3096
±15kV ESD-Protected, 10Mbps, 3V/5V,
Quad RS-422/RS-485 Receivers
Switching Characteristics—MAX3095
(VCC = 5V ±5%, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
VCC = 5V ±5%, TA = TMIN to TMAX
Input-to-Output Propagation
Delay
tPLH, tPHL
VCC = 5.25V
|VID| = 3V,
Figure 2
VCC = 4.75V
Device-to-Device PropagationDelay Matching
MIN
TYP
65
MAX
UNITS
98
TA = +85°C
78
86
94
TA = +25°C
71
79
87
TA = -40°C
65
73
81
TA = +85°C
82
90
98
TA = +25°C
74
82
90
TA = -40°C
68
76
84
|VID| = 3V, Figure 2, matched conditions
ns
16
ns
-4
±10
ns
Propagation-Delay Skew
(tPLH - tPHL)
tSK
Output Enable Time to Low
Level
tZL
Figure 3
600
800
ns
Output Enable Time to High
Level
tZH
Figure 3
600
800
ns
Output Disable Time from Low
Level
tLZ
Figure 3
60
100
ns
Output Disable Time from High
Level
tHZ
Figure 3
60
100
ns
Maximum Data Rate
fMAX
10
Mbps
DC Electrical Characteristics—MAX3096
(VCC = 3.135V to 3.6V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at VCC = 3.3V, TA = +25°C.) (Note 1)
PARAMETER
Receiver Differential Input
Threshold
SYMBOL
VTH
Receiver Input Hysteresis
Receiver Input Current (A_, B_)
CONDITIONS
-7V ≤ VCM ≤ 12V
VCM = 0V
IIN
VCC = 0V or 3.6V
Enable Input Current (G, G)
Enable Input High Voltage (G, G)
Enable Input Low Voltage (G, G)
MIN
TYP
-200
MAX
UNITS
200
mV
45
VIN = 12V
VIN = -7V
VIH
mV
250
-200
±1
2.0
VIL
µA
µA
V
0.8
V
Receiver Output High Voltage
VOH
IOUT = -1.5mA, VID = 200mV,
G = VCC or G = GND, Figure 1
Receiver Output Low Voltage
VOL
IOUT = 2.5mA, VID = -200mV,
G = VCC or G = GND, Figure 1
0.4
V
Three-State Current at Receiver
Output
IOZR
0 ≤ VOUT ≤ VCC, G = GND and G = VCC
±1
µA
Output Short-Circuit Current
IOSR
0 ≤ VOUT ≤ VCC, G = VCC or G = GND
±60
mA
Receiver Input Resistance
www.maximintegrated.com
RIN
-7V ≤ VCM ≤ 12V
VCC - 0.4
±4
48
V
kΩ
Maxim Integrated │ 3
MAX3095/MAX3096
±15kV ESD-Protected, 10Mbps, 3V/5V,
Quad RS-422/RS-485 Receivers
DC Electrical Characteristics—MAX3096 (continued)
(VCC = 3.135V to 3.6V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at VCC = 3.3V, TA = +25°C.) (Note 1)
PARAMETER
Supply Current
SYMBOL
ICC
ESD Protection
(Note 2)
CONDITIONS
No load, G = VCC or G = GND
G = GND and G = VCC
Human Body Model
IEC 1000-4-2 (Air-Gap Discharge)
IEC 1000-4-2 (Contact Discharge)
MIN
TYP
2.4
0.001
±15
±15
±8
MAX
4.0
10
TYP
MAX
UNITS
mA
µA
kV
Switching Characteristics—MAX3096
(VCC = 3.135V to 3.6V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
VCC = 3.135V to 3.6V, TA = TMIN to TMAX
Input-to-Output Propagation
Delay
tPLH, tPHL
VCC = 3.60V
|VID| = 3V,
Figure 2
VCC = 3.135V
Device-to-Device PropagationDelay Matching
TA = +85°C
TA = -40°C
69
88
98
112
TA = +25°C
78
88
102
69
79
93
TA = +85°C
103
113
127
91
101
115
TA = -40°C
82
92
106
TA = +25°C
UNITS
127
|VID| = 3V, Figure 2, matched conditions
ns
24
ns
-2
±10
ns
Propagation-Delay Skew
(tPLH - tPHL)
tSK
Output Enable Time to Low
Level
tZL
Figure 3
600
1000
ns
Output Enable Time to High
Level
tZH
Figure 3
600
1000
ns
Output Disable Time from Low
Level
tLZ
Figure 3
80
180
ns
Output Disable Time from High
Level
tHZ
Figure 3
80
180
ns
Maximum Data Rate
fMAX
10
Mbps
Note 1: All currents into the device are positive; all currents out of the device are negative. All voltages are referred to device ground,
unless otherwise noted.
Note 2: Receiver inputs (A_, B_).
www.maximintegrated.com
Maxim Integrated │ 4
MAX3095/MAX3096
±15kV ESD-Protected, 10Mbps, 3V/5V,
Quad RS-422/RS-485 Receivers
Typical Operating Characteristics
(VCC = 5V for MAX3095, VCC = 3.3V for MAX3096, TA = +25°C, unless otherwise noted.)
OUTPUT CURRENT vs.
OUTPUT HIGH VOLTAGE
-20
MAX3096
-10
0
1
2
3
4
15
10
MAX3096
IOUT = 8mA
0.8
0.7
0.6
0.5
0.4
MAX3096
0.3
MAX3095
0.2
0.1
0
1
2
3
4
0
5
-40
-15
10
35
60
OUTPUT HIGH VOLTAGE (V)
TEMPERATURE (°C)
OUTPUT HIGH VOLTAGE
vs. TEMPERATURE
SUPPLY CURRENT vs. TEMPERATURE
SHUTDOWN SUPPLY CURRENT
vs. TEMPERATURE
SUPPLY CURRENT (mA)
MAX3096
1
2.6
MAX3095/MAX3096
2.4
2.2
IOUT = -8mA
10
35
60
2.0
85
-40
TEMPERATURE (°C)
-15
10
35
60
MAX3096
5
0
-40
90
80
-15
10
35
60
85
TEMPERATURE (°C)
MAX3096
PROPAGATION DELAY vs. TEMPERATURE
140
MAX3095-07
│VID│ = 3V
CL = 15pF
100
70
MAX3095
TEMPERATURE (°C)
PROPAGATION DELAY (ns)
PROPAGATION DELAY (ns)
110
10
85
MAX3095
PROPAGATION DELAY vs. TEMPERATURE
120
15
130
MAX3095-08
-15
85
MAX3095-06
2.8
20
SHUTDOWN SUPPLY CURRENT (nA)
3.0
MAX3095-04
3
-40
0.9
OUTPUT LOW VOLTAGE (V)
4
2
0
5
MAX3095
OUTPUT HIGH VOLTAGE (V)
20
5
5
0
MAX3095
MAX3095-05
0
25
OUTPUT LOW VOLTAGE (V)
-30
1.0
MAX3095-02
MAX3095-01
MAX3095
-40
30
OUTPUT CURRENT (mA)
OUTPUT CURRENT (mA)
-50
OUTPUT LOW VOLTAGE
vs. TEMPERATURE
MAX3095-03
OUTPUT CURRENT vs.
OUTPUT LOW VOLTAGE
│VID│= 3V
CL = 15pF
120
110
100
90
-40
-15
10
35
TEMPERATURE (°C)
www.maximintegrated.com
60
85
80
-40
-15
10
35
60
85
TEMPERATURE (°C)
Maxim Integrated │ 5
MAX3095/MAX3096
±15kV ESD-Protected, 10Mbps, 3V/5V,
Quad RS-422/RS-485 Receivers
Typical Operating Characteristics (continued)
(VCC = 5V for MAX3095, VCC = 3.3V for MAX3096, TA = +25°C, unless otherwise noted.)
SHUTDOWN TIMING
MAX3095 TOC09
MAX3095
Y VOLTAGE
5V/div
2V/div
MAX3096
Y VOLTAGE
G VOLTAGE
2V/div
TIME (200ns/div)
CIRCUIT OF FIGURE 3,
S1 OPEN, S2 CLOSED, S3 = 1V
www.maximintegrated.com
Maxim Integrated │ 6
MAX3095/MAX3096
±15kV ESD-Protected, 10Mbps, 3V/5V,
Quad RS-422/RS-485 Receivers
Pin Configuration
TOP VIEW
B1 1
+
16 VCC
15 B4
A1 2
Y1 3
G 4
MAX3095
MAX3096
14 A4
13 Y4
Y2 5
12 G
A2 6
11 Y3
B2 7
10 A3
9
GND 8
B3
DIP/SO/QSOP
Pin Description
PIN
NAME
1
B1
Inverting Receiver Input
FUNCTION
2
A1
Noninverting Receiver Input
3
Y1
Receiver Output. Enabled when G = high OR G = low. Y1 is logic-high if VA1 > VB1 by 200mV, and low if
VA1 < VB1 by 200mV. Y1 is logic-high if VA1 and VB1 remain unconnected. Otherwise, the state is undetermined. Y1 goes high impedance when the G = low and G = high.
4
G
Active-High Receiver Output Enable. A logic-high on this input enables all receivers. When taken low and G
is high, all receivers are shut down, and the outputs go high impedance.
5
Y2
Receiver Output. Same functionality as Y1.
6
A2
Noninverting Receiver Input
7
B2
Inverting Receiver Input
8
GND
9
B3
Inverting Receiver Input
10
A3
Noninverting Receiver Input
11
Y3
Receiver Output. Same functionality as Y1.
12
G
Active-Low Receiver Output Enable. A logic-low on this input enables all receivers. When G = high and
G = low, all receivers are shut down, and the outputs go high impedance.
13
Y4
Receiver Output. Same functionality as Y1.
14
A4
Noninverting Receiver Input
15
B4
Inverting Receiver Input
16
VCC
Ground
Positive Supply
www.maximintegrated.com
Maxim Integrated │ 7
MAX3095/MAX3096
±15kV ESD-Protected, 10Mbps, 3V/5V,
Quad RS-422/RS-485 Receivers
|VID| = 3V
VID
VID
OUT
R
CL
15pF
R
G = VCC or G = GND
3.0V
VOL
VOH
IOL
(+)
IN
IOH
(-)
1.5V
1.5V
0V
tPLH
tPHL
VCC
1.5V (MAX3096)
2.0V (MAX3095)
OUT
Figure 1. Receiver VOH and VOL
1.5V (MAX3096)
2.0V (MAX3095)
0
Figure 2. Receiver Propagation Delay
VCC
S3
+1V
S1
G
-1V
VID
VCC
1k
R
S2
CL
15pF
G
3V
G
1.5V
1.5V
3V
G
0
tZH
tLZ
VOH
OUT
0
tHZ
1.5V
0.25V
tZL
VCC
OUT
1.5V
VOL
0
S1 OPEN
S2 CLOSED
S3 = 1V
0.25V
S1 CLOSED
S2 OPEN
S3 = -1V
Figure 3. Receiver Enable and Disable Times
www.maximintegrated.com
Maxim Integrated │ 8
MAX3095/MAX3096
±15kV ESD-Protected, 10Mbps, 3V/5V,
Quad RS-422/RS-485 Receivers
Detailed Description
The main difference between tests done using the Human
Body Model and IEC 1000-4-2 is higher peak current
in IEC 1000-4-2. Because series resistance is lower in
the IEC 1000-4-2 ESD test model (Figure 5a), the ESDwithstand voltage measured to this standard is generally
lower than that measured using the Human Body Model.
Figure 5b shows the current waveform for the ±8kV IEC
1000-4-2 Level 4 ESD Contact-Discharge test. The AirGap test involves approaching the device with a charge
probe. The Contact-Discharge method connects the
probe to the device before the probe is energized.
±15kV ESD Protection
As with all Maxim devices, ESD-protection structures
are incorporated on all pins to protect against electrostatic discharges (ESD) encountered during handling and
assembly. The MAX3095/MAX3096 receiver inputs have
extra protection against static electricity found in normal
operation. Maxim’s engineers developed state-of-the-art
structures to protect these pins against ±15kV ESD, without damage. After an ESD event, the MAX3095/MAX3096
continue working without latchup.
ESD protection can be tested in several ways. The receiver
inputs are characterized for protection to the following:
1) ±15kV using the Human Body Model
2) ±8kV using the Contact-Discharge Method specified in
IEC 1000-4-2 (formerly IEC 801-2)
3) ±15kV using the Air-Gap Method specified in IEC
1000-4-2 (formerly IEC 801-2)
ESD Test Conditions
ESD performance depends on a number of conditions.
Contact Maxim for a reliability report that documents test
setup, methodology, and results.
Human Body Model
Figure 4a shows the Human Body Model, and Figure
4b shows the current waveform it generates when
discharged into a low impedance. This model consists of
a 100pF capacitor charged to the ESD voltage of interest,
which is then discharged into the device through a 1.5kΩ
resistor.
IEC 1000-4-2
Since January 1996, all equipment manufactured and/
or sold in the European community has been required to
meet the stringent IEC 1000-4-2 specification. The IEC
1000-4-2 standard covers ESD testing and performance
of finished equipment; it does not specifically refer to integrated
circuits. The MAX3095/MAX3096 help you design equipment
that meets Level 4 (the highest level) of IEC 1000-4-2,
without additional ESD-protection components.
www.maximintegrated.com
Machine Model
The Machine Model for ESD testing uses a 200pF storage
capacitor and zero-discharge resistance. It mimics the
stress caused by handling during manufacturing and
assembly. Of course, all pins (not just RS-485 inputs)
require this protection during manufacturing. Therefore,
the Machine Model is less relevant to the I/O ports than
are the Human Body Model and IEC 1000-4-2.
Low-Power Shutdown Mode
Table 1 shows the functionality of the enable inputs. The
MAX3095/MAX3096 enter shutdown when G is low and
G is high. In shutdown, all outputs go high impedance and
the devices typically draw less than 1nA. The devices exit
shutdown by taking G high or G low. The typical shutdown
exit time is 600ns.
Table 1. Function Table
(A - B)
OUTPUT
Y
DEVICE
MODE
X
≥ 200mV
1
On
X
≤ -200mV
0
On
G
G
1
1
1
X
Open
1
On
X
0
≥ 200mV
1
On
X
0
≤ -200mV
0
On
X
0
Open
1
On
0
1
X
High-Z
Shutdown
X = don’t care, High-Z = high impedance
Maxim Integrated │ 9
MAX3095/MAX3096
RC
1M
CHARGE-CURRENT
LIMIT RESISTOR
HIGHVOLTAGE
DC
SOURCE
Cs
100pF
±15kV ESD-Protected, 10Mbps, 3V/5V,
Quad RS-422/RS-485 Receivers
RD
1.5k
IP 100%
90%
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
DEVICE
UNDER
TEST
HIGHVOLTAGE
DC
SOURCE
Cs
150pF
36.8%
10%
0
DEVICE
UNDER
TEST
10%
tr = 0.7ns to 1ns
www.maximintegrated.com
tDL
CURRENT WAVEFORM
I
100%
90%
DISCHARGE
RESISTANCE
Figure 5a. IEC 1000-4-2 ESD Test Model
TIME
tRL
Figure 4b. Human Body Model Current Waveform
RD
330Ω
STORAGE
CAPACITOR
0
IPEAK
CHARGE-CURRENT
LIMIT RESISTOR
PEAK-TO-PEAK RINGING
(NOT DRAWN TO SCALE)
AMPERES
Figure 4a. Human Body ESD Test Model
RC
50M to 100M
Ir
30ns
t
60ns
Figure 5b. IEC 1000-4-2 ESD-Generator Current Waveform
Maxim Integrated │ 10
MAX3095/MAX3096
±15kV ESD-Protected, 10Mbps, 3V/5V,
Quad RS-422/RS-485 Receivers
Applications Information
Propagation-Delay Matching
The MAX3095/MAX3096 exhibit propagation delays that
are closely matched from one device to another, even
between devices from different production lots. This feature
allows multiple data lines to receive data and clock
signals with minimal skewing with respect to each other.
The MAX3095 receiver propagation delays are trimmed to
a predetermined value ±8ns, while the MAX3096 delays
are trimmed to a predetermined value ±10ns.
VCC
1k
A
150Ω
128 Receivers on the Bus
The standard RS-485 input impedance is 12kΩ (one-unit
load). The standard RS-485 transmitter can drive 32 unit
loads. The MAX3095/MAX3096 present a 1/4-unit-load
input impedance (48kΩ), which allows up to 128 receivers
on a bus. Any combination of these RS-485 receivers with
a total of 32 unit loads can be connected to the same bus.
MAX3095
MAX3096
B
1k
Figure 6. External Fail-Safe Implementation
Fail-Safe Implementation
The MAX3095/MAX3096 receiver inputs guarantee a
logic high output when the inputs are open circuit (no
termination resistor used). This occurs when the transmitter
is removed from the bus or when all transmitter outputs
are high impedance. However, when the line is terminated
and the transmitters are disabled, the differential voltage
between the A and B inputs falls below the ±200mV
RS-485 sensitivity threshold. Consequently, the outputs
become undefined. To maintain a fail-safe receiver output while using a terminating resistor, input A must be
biased at least 200mV above input B. The resistor-divider
network shown in Figure 6 is recommended.
www.maximintegrated.com
Maxim Integrated │ 11
MAX3095/MAX3096
±15kV ESD-Protected, 10Mbps, 3V/5V,
Quad RS-422/RS-485 Receivers
Ordering Information
Package Information
PART
TEMP RANGE
PIN-PACKAGE
MAX3095CPE+
0°C to +70°C
16 Plastic DIP
MAX3095CSE+
0°C to +70°C
16 Narrow SO
MAX3095CEE+
0°C to +70°C
16 QSOP
MAX3095EPE+
-40°C to +85°C
16 Plastic DIP
MAX3095ESE+
-40°C to +85°C
16 Narrow SO
MAX3095EEE+
-40°C to +85°C
16 QSOP
MAX3096CPE+
0°C to +70°C
16 Plastic DIP
MAX3096CSE+
0°C to +70°C
16 Narrow SO
MAX3096CEE+
0°C to +70°C
16 QSOP
MAX3096EPE+
-40°C to +85°C
16 Plastic DIP
MAX3096ESE+
-40°C to +85°C
16 Narrow SO
MAX3096EEE+
-40°C to +85°C
16 QSOP
+Denotes a lead(Pb)-free/RoHS-compliant package.
For the latest package outline information and land patterns
(footprints), go to www.maximintegrated.com/packages. Note
that a “+”, “#”, or “-” in the package code indicates RoHS status
only. Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PACKAGE TYPE
PACKAGE CODE
DOCUMENT NO.
16 QSOP
E16+5
21-0055
16 Narrow SO
S16+5
21-0041
16 PDIP
P16+1
21-0043
Chip Information
PROCESS: BiCMOS
www.maximintegrated.com
Maxim Integrated │ 12
MAX3095/MAX3096
±15kV ESD-Protected, 10Mbps, 3V/5V,
Quad RS-422/RS-485 Receivers
Revision History
REVISION
NUMBER
REVISION
DATE
2
1/10
3
1/10
● Updated all the parts in the Ordering Information to be lead-free.
● Updated the Y1 description in the Pin Description.
● Changed the Chip Information section to “PROCESS: BiCMOS”.
4
1/18
Updated Absolute Maximum Rating section
PAGES
CHANGED
DESCRIPTION
● Changed the lower specification in the VCC range from 3.0V to 3.135V.
● Updated the MAX specifications for the “Input-to-Output Propagation Delay” in the
Switching Characteristics—MAX3096 table.
3, 4
1, 6, 10
2
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits)
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
© 2018 Maxim Integrated Products, Inc. │ 13
工商网监
湘ICP备2023018690号
