MAX3658AEVKIT

19-3088; Rev 2, 01/04     "! #%$'&)( *+$,# -.-.-.-.-.-.-.-.-.-.-.-.-.-.-.- /103240357698;:357?A@CBD?FE32 G.G.G.G.G.G.G.G.G.G.G.G.G.G.G.G.G.G.G.G.G.G.G.G.G.G.G.G H;IKJMLONQPRIQS The MAX3658A evaluation kit is a fully assembled electrical demonstration kit that provides easy evaluation of the MAX3658A 622Mbps +3.3V trans-impedance amplifier. ♦ Easy +3.3V Electrical Evaluation of the MAX3658A ♦ Fully Assembled and Tested Note that the MAX3658A evaluation kit provides an electrical interface to the IC that is similar, but not exactly the same as a photodiode. ♦ EV Kit Designed for 50Ω Ω Interfaces DESIGNATION QTY DESCRIPTION 2.2µF ±10% Ceramic Capacitor (1206) DESIGNATION QTY DESCRIPTION R24, R25, R30, 4 1.58kΩ ±1% resistor (0402) R31 T.T.T.T.T.T.T.T.T.T.T.T.T.T.T.T.T.T.T.T UCV3W)XYV3Z4[3Z]\_^9`bac\
    d.d.d.d.d.d.d.d.d.d.d.d egf3h)i_f3j4kQj]lnmporq;ltsFu9f3jvlxwAy   C0, C20 2 C1, C21 2 0.1µF ±10% Ceramic Capacitor (0603) TP0 – TP11 12 TESTPOINT DIGI-KEY 5000KND C2, C13 2 100pF ±5% Ceramic Capacitor (0201) U0 1 User Supplied 5 PIN TO CAN U1, U2 2 MAX3658AETA 8 TDFN C3, C12, C15, C18, C23 5 2200pF ±5% Ceramic Capacitor (0201) U3, U4 2 User Supplied 4 PIN TO CAN C4, C6 – C8, C14, C17, C19, C22, C24, C27 10 1µF ±5% Ceramic Capacitor (0603) C5, C11 2 0.01µF ±10% Ceramic Capacitor (0402) C9, C10, C29 3 0.022µF ±10% Ceramic Capacitor (0402) J2, J3, J7, J15 4 SMB connectors (PCB-mount) J4, J6, J20, J28, J30, JU1 6 2-pin headers (0.1in centers) J9 – J11, J13, J14, J16, J19, J21 – J27 14 SMA connectors (edge-mount, tab contact) L1, L2 2 600Ω ferrite beads (0603) BLM15BD601SN R0, R3 2 1.5kΩ ±1% resistor (0402) R1, R2 2 3kΩ ±1% resistor (0402) R4, R5 2 374Ω ±1% resistor (0402) R8 – R11, R26 – R29, R33, R34 10 150Ω ±1% resistor (0402) R12 – R14 3 51.1Ω ±1% resistor (0402) R16 – R21 6 2.37kΩ ±1% resistor (0402) z.z.z.z.z.z.z.z.z.z.z.z.z.z.z {t|~}9Q|€b‚9ƒ„…‚4†ˆ‡3|Š‰Œ‹4D€F‡3‚ PART TEMP. RANGE IC PACKAGE MAX3658AEVKIT -40°C to +85°C 8- TDFN Ž.Ž.Ž.Ž.Ž.Ž.Ž.Ž.Ž.Ž.Ž.Ž.Ž.Ž C3‘)’Y3“4”3“]•g–]—˜’9’]™…šF”3›Šœ PHONE FAX AVX SUPPLIER 843-444-2863 843-626-3123 Coilcraft 847-639-6400 847-639-1469 Digi-Key 218-681-6674 218-681-3380 EF Johnson 402-474-4800 402-474-4858 Murata 415-964-6321 415-964-8165 Note: Please indicate that you are using the MAX3658A when ordering from these suppliers. _________________________________________________________________Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1  žŸ  ¡¢£ž ¤¥§¦ ¨"© ¦ª¬«'­)® ¯°«,ª Á¼À Â.Â.Â.Â.Â.Â.Â.Â.Â.Â.Â.Â.Â.Â.Â.Â.Â.Â.Â.Â.Â.Â.Â.Â. Ã1ÄKÅFÆ3ÇÈ_ÉËÊÍÌÎÉ ÏÑÐÓÑÒ"Ô9pÕ%Ö,×ÓÑØÚâÙ%ÛÜÐÑݘãÔ9Þ9Ð,äÖ,×ÓÑØàAßDËÐ,á ¾¿½ »¼ ¹· ¸´º µ³´¶ ³± ² • • • +3.3V power supply with 100mA current capability 1) Connect a signal source to J11 (IN1 AC). Set the signal amplitude to 960mVP-P (Corresponding to 200µAP-P current into the TIA). Set the data rate to 622Mbps. 2) Apply 100µA to the IN1 DC input (J7) using a DC current source to emulate the DC component of the input signal. A voltage source connected from J7 to GND may be used if a DC current source is not available. Signal-source, 622Mbps capability å˜æËDçä,è,é,ê,äëÑæDËé Oscilloscope with at least 500MHz performance 3) Connect OUT1+ (J10) and OUT1- (J9) to the 50Ω inputs of a high-speed oscilloscope. 4) Remove the shunt from J20 to enable the DC cancellation loop. Install the shunt on J28 to enable the average current monitor. Connect a +3.3V supply and ground to J2 SMB terminal. The differential signal at the oscilloscope should be approximately 240mVP-P. 5) 6) 7) ì.ì.ì.ì.ì.ì.ì.ì.ì.ì.ì.ì.ì.ì.ì í