Click here to ask about the production status of specific part numbers.
MAX38888
2.5V to 5.0V, 0.5A/2.5A Reversible Buck/Boost
Regulator for Backup Power Applications
General Description
Benefits and Features
The MAX38888 is a storage capacitor or capacitor bank
backup regulator designed to efficiently transfer power between a storage element and a system supply rail in reversible buck and boost operations using the same inductor.
●
●
●
●
●
●
●
●
When the main supply is present and above the minimum
system supply voltage, the regulator operates in buck
mode and charges the storage element at up to 500mA
peak inductor current. Once the storage element is
charged, the circuit draws only 2.5µA of current while it
maintains the supercapacitor or other storage element in
its ready state. When the main supply is removed, the regulator operates in boost mode and prevents the system
from dropping below the minimum operating voltage, discharging the storage element at up to 2.5A peak inductor
current.
The MAX38888 is externally programmable for minimum
and maximum voltage of the storage element, such as
supercapacitor, minimum system voltage, and maximum
charge and discharge currents. The internal DC-DC converter requires only a 1µH inductor.
Applications
● Handheld Industrial Equipment
● Portable Computers
● Portable Devices with a Removable Battery
19-100369; Rev 5; 8/20
2.5V to 5V System Output Voltage
0.8V to 4.5V Cap Voltage Range
Up to 2.5A Peak Inductor Discharge Current
Programmable Voltage and Current Thresholds
±2% Threshold Accuracy
Up to 95% Efficiency, Charge or Discharge
2.5μA Ready Quiescent Current
Small Solution Size
• 3mm x 3mm x 0.75mm TDFN Package
Ordering Information appears at end of data sheet.
MAX38888
2.5V to 5.0V, 0.5A/2.5A Reversible Buck/Boost
Regulator for Backup Power Applications
Typical Application Circuit
CHARGE
500mA (MAX)
DISCHARGE
2.5A (MAX)
L1
1µH
VSC
2.7V (MAX)
1.5V (MIN)
CAP
10F
SUPERCAP
C2
22µF
R3
1.8MΩ
LX
SYS
R7
1MΩ
MAX38888
R8
1MΩ
R6
2.49MΩ
C1
22µF
FBCL
R2
402kΩ
EN
R1
499kΩ
www.maximintegrated.com
MAIN
BATTERY
(REMOVABLE)
FBS
BACKUP
READY
BKUPB
RDY
FBCH
ENABLE
INPUT
VSYS
SYSTEM LOAD
3V (MIN)
GND
ISET
R4
20kΩ
R5
499kΩ
Maxim Integrated | 2
MAX38888
2.5V to 5.0V, 0.5A/2.5A Reversible Buck/Boost
Regulator for Backup Power Applications
Absolute Maximum Ratings
CAP, EN, SYS, LX, BKUPB, RDY to GND............... -0.3V to +6V
FBCH, FBCL to GND.................................... -0.3V to CAP + 0.3V
FBS, ISET to GND........................................ -0.3V to SYS + 0.3V
PGND to GND ....................................................... -0.3V to +0.3V
Continuous Power Dissipation (TA = +70°C, TDFN,
derate 24.4mW/°C above +70°C) ............................ 1951.2mW
Operating Temperature Range ...........................-40°C to +125°C
Storage Temperature Range ..............................-65°C to +150°C
Maximum Junction Temperature ...................................... +150°C
Lead Temperature (soldering, 10 seconds) ......................+300°C
LX RMS Current........................................................... ±2.0ARMS
Output Short-Circuit Duration......................................Continuous
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the
device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
Package Information
TDFN
Package Code
T1433+2C
Outline Number
21-0137
Land Pattern Number
90-0063
THERMAL RESISTANCE, FOUR-LAYER BOARD
Junction-to-Ambient (θJA)
41°C/W
Junction-to-Case Thermal Resistance (θJC)
8°C/W
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages.
Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different
suffix character, but the drawing pertains to the package regardless of RoHS status.
Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a
four-layer board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/
thermal-tutorial.
Electrical Characteristics
(VSYS = 3.7V, VCAP = 2.7V, TJ = -40°C to +125°C (typical values at TJ = +25°C), circuit of Figure 1, unless otherwise specified.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
SYS Voltage Range
VVSYS
2.5
5
V
CAP Voltage Range
VVSC
0.8
4.5
V
SYS Shutdown Current
ISYS_SD
EN = 0V, TA = +25°C
0.01
EN = 0V
0.1
SYS Charging Supply
Current
ISYS_CHG
VFBS = 0.6V, VFBCH = VFBCL = 0.485V
1.5
SYS Backup Supply
Current
ISYS_BUP
VFBS = VFBCH = VFBCL = 0.515V, TA =
+25°C
35
VFBS = VFBCH = VFBCL = 0.515V
35
SYS Ready Supply
Current
ISYS_RDY
VFBS = 0.6V, VFBCH = VFBCL = 0.515V,
TA = +25°C
2.5
VFBS = 0.6V, VFBCH = VFBCL = 0.515V
2.5
CAP Shutdown Current
ICAP_SD
EN = 0V, TA = +25°C
0.01
EN = 0V
0.1
www.maximintegrated.com
1
μA
mA
65
5
1
μA
μA
μA
Maxim Integrated | 3
MAX38888
2.5V to 5.0V, 0.5A/2.5A Reversible Buck/Boost
Regulator for Backup Power Applications
Electrical Characteristics (continued)
(VSYS = 3.7V, VCAP = 2.7V, TJ = -40°C to +125°C (typical values at TJ = +25°C), circuit of Figure 1, unless otherwise specified.)
PARAMETER
UVLO Threshold
FBS Backup Voltage
FBS Charging
Threshold
SYMBOL
VUVLOF
VFBS
CONDITIONS
MIN
TYP
MAX
UNITS
VVSYS falling, 100mV typical hysteresis
1.7
FBS rising, when discharging stops
-2%
1.8
1.9
V
0.5
+2%
V
VTH_FBS_CHG
Above FBS backup voltage, when
charging begins, 30mV typical hysteresis
25
60
95
mV
FBCH Threshold
VTH_FBCH
FBCH rising, when charging stops, 25mV
typical hysteresis
-2%
0.5
+2%
V
FBCL Threshold
VTH_FBCL
FBCL falling, when preserve mode starts,
25mV typical hysteresis
-3.5%
0.475
+3.5%
V
225
600
EN Threshold
ISET Resistor Range
LX Peak Backup
Current Limit (Note 1)
LX Peak Charge Current
Limit (Note 1)
FBS/FBCH/FBCL Input
Bias Current
VIL
When LX stops switching, EN falling
VIH
EN rising
RISET
IDCHG
ICHG
IFBS/FBCH/
FBCL
EN Input Leakage
Current
IEN
LX Switching Frequency
fSW
LX Low-Side FET
Resistance
LX High-Side FET
Resistance
LX Leakage Current
660
Guaranteed by LX peak current limits
20
Circuit of Figure 1, VCAP = 2V, VSYS =
2.9V, RISET = 20kΩ
2.0
400
3.0
500
600
mA
100
-0.1
VFBS/FBCH/FBCL = 0.5V
0V < VEN < 5.5V, TA = +25°C
2.5
kΩ
0.50
Circuit of Figure 1, VSYS = 3.7V, VCAP =
2V, RISET = 100kΩ
VFBS/FBCH/FBCL = 0.5V, TA = +25°C
100
mV
A
Circuit of Figure 1, VCAP = 2V, VSYS =
2.9V, RISET = 100kΩ
Circuit of Figure 1, VSYS = 3.7V, VCAP =
2V, RISET = 20kΩ
925
0.001
0.1
0.01
-0.1
0V < VEN < 5.5V
0.001
0.1
0.01
μA
μA
Delivering maximum current from CAP
2
RLOW
VSYS = 3V, LX switched to GND
50
100
mΩ
RHIGH
VSYS = 3V, LX switched to SYS
80
160
mΩ
ILX_LKG
VEN = 0V, VSYS = 5V, VLX = 0V/5V, TA =
+25°C
-1
VEN = 0V, VSYS = 5V, VLX = 0V/5V
MHz
1
μA
0.1
Maximum On-Time
tON
Backup mode, VFBS = 0.485V
320
400
480
ns
Minimum Off-Time
tOFF
Backup mode, VFBS = 0.485V
80
100
120
ns
Overtemperature
Lockout Threshold
TOTLO
TJ rising, 15°C typical hysteresis
165
°C
High-Side FET ZeroCrossing (Note 1)
IZXP
Circuit of Figure 1, VCAP = 2V, VSYS =
2.9V
25
50
75
mA
Low-Side FET ZeroCrossing (Note 1)
IZXN
Circuit of Figure 1, VSYS = 3.7V, VCAP =
2V
25
50
75
mA
VEN = 0V, VBKUPB = 5V, TA = +25°C
-1
BKUPB Leakage
Current
www.maximintegrated.com
IBKUPB
VEN = 0V, VBKUPB = 5V
1
0.1
μA
Maxim Integrated | 4
MAX38888
2.5V to 5.0V, 0.5A/2.5A Reversible Buck/Boost
Regulator for Backup Power Applications
Electrical Characteristics (continued)
(VSYS = 3.7V, VCAP = 2.7V, TJ = -40°C to +125°C (typical values at TJ = +25°C), circuit of Figure 1, unless otherwise specified.)
PARAMETER
SYMBOL
CONDITIONS
BKUPB Output Voltage
Low
VBKUPB_L
VFBS = 0.48V, VFBCH = VFBCL = 0.515V,
ISINK = 2mA
RDY Leakage Current
IRDY
RDY Output Voltage
Low
VRDY_L
VFBCH = 0.54V, VRDY = 5V, TA = 25°C
VFBCH = 0.54V, VRDY = 5V
VEN = 0V, ISINK = 2mA
MIN
TYP
-1
MAX
UNITS
0.4
V
1
0.1
0.4
μA
V
Note 1: DC measurement, actual zero-crossing, and peak current accuracy in the circuit will be affected by the propagation delay time.
www.maximintegrated.com
Maxim Integrated | 5
MAX38888
2.5V to 5.0V, 0.5A/2.5A Reversible Buck/Boost
Regulator for Backup Power Applications
Typical Operating Characteristics
(VSYS = 3.6V, VCAP = 2.0V, C1 = 22μF, C2 = 22μF, TA = +25°C, unless otherwise noted.)
www.maximintegrated.com
Maxim Integrated | 6
MAX38888
2.5V to 5.0V, 0.5A/2.5A Reversible Buck/Boost
Regulator for Backup Power Applications
Typical Operating Characteristics (continued)
(VSYS = 3.6V, VCAP = 2.0V, C1 = 22μF, C2 = 22μF, TA = +25°C, unless otherwise noted.)
LX
CAP
EN
FBCH
FBCL
11
10
9
8
N.C
12
PGND
13
TOP VIEW
14
Pin Configuration
MA X388 88
EXPOSED PAD
.
1
2
3
4
5
6
7
SYS
N.C
BKUPB
RDY
ISET
FBS
GND
+
TD FN-EP
3m m x 3m m
www.maximintegrated.com
Maxim Integrated | 7
MAX38888
2.5V to 5.0V, 0.5A/2.5A Reversible Buck/Boost
Regulator for Backup Power Applications
Pin Description
PIN
NAME
FUNCTION
1
SYS
System Supply Rail. Connect to a system supply rail or removable battery between 2.5V and 5V
and bypass with a 22μF capacitor to GND.
2
NC
No Connect.
3
BKUPB
4
RDY
Open-Drain Supercap Ready Indicator. RDY goes high when the supercapacitor is fully charged
(i.e., FBCH > 0.5V). RDY is pulled low when FBCL < 0.475V. Connect to an external pullup
resistor.
5
ISET
Charge/Discharge Current Input. The peak discharge current is set by 50kV/RISET while the peak
charging current is 1/5 the discharging current.
6
FBS
SYS Feedback. Connect to the center point of a resistor divider from SYS to GND.
SYS will boost to 0.5V x (1 + RSTop/RSBot) when VFBS < 0.5V.
7
GND
Analog Ground.
8
FBCL
CAP Feedback. Connect to the upper point of a resistor divider from CAP to GND. Part enters
preserve mode when VFBCL < 0.475V.
9
FBCH
CAP Feedback. Connect to the lower point of a resistor divider from CAP to GND. CAP will charge
to 0.5V x (1 + RCTop/RCBot) when VFBS > 0.56V.
10
EN
11
CAP
Open-Drain Backup Indicator. BKUPB is held low when the part is in backup mode (i.e., when FBS
< 0.5V and FBCL > 0.5V). BKUPB is released high when FBCL < 0.475V or FBS > 0.56V. Connect
to an external pullup resistor.
Enable Input. Force this pin high to enable the regulator or force pin low to disable the part and
enter shutdown. If not driven, tie it to the SYS rail.
Super Cap. Connect to a supercapacitor rated between 0.8V to 5V with a maximum voltage less
than VSYS.
12
LX
Inductor Switching Node. Connect a 1.0μH to 4.7uH inductor from LX to CAP.
13
NC
No Connect.
14, EP
PGND
www.maximintegrated.com
Power Ground.
Maxim Integrated | 8
MAX38888
2.5V to 5.0V, 0.5A/2.5A Reversible Buck/Boost
Regulator for Backup Power Applications
Functional Diagram
CAP
SYS
BIAS
EN
LX
DRIVERS
CONTROL
ISET
PGND
RDY
BKUPB
MAX38888
FBS
MODE
SELECT
FBCH
FBCL
GND
www.maximintegrated.com
Maxim Integrated | 9
MAX38888
2.5V to 5.0V, 0.5A/2.5A Reversible Buck/Boost
Regulator for Backup Power Applications
Detailed Description
The MAX38888 is a flexible storage capacitor or capacitor bank backup regulator efficiently transferring power between
a storage element and a system supply rail.
When the main supply is present and its voltage above the minimum system supply voltage, the regulator operates in the
charging mode of operation and charges the storage element at up to 500mA peak inductor current. Once the storage
element is charged, the RDY flag will assert and the circuit will draw only 2.5μA of current while maintaining the storage
element in its ready state.
When the main supply is removed, the regulator prevents the system from dropping below the minimum operating
voltage, boosting VSYS by discharging the storage element at up to 2.5A peak inductor current. During this backup mode
of operation, the MAX38888 utilizes a fixed on-time, current-limited, pulse-frequency-modulation (PFM) control scheme.
Once MAX38888 is in the backup mode, the BKUPB flag is asserted. When VSYS is applied for the first time, ensure that
the supercapacitor is charged to 2.7V to activate backup mode.
The external pins allow a wide range of system and storage element, such as supercapacitor voltage settings, as well as
charging and discharging peak inductor current settings.
The MAX38888 implements a True Shutdown™ feature, disconnecting VSYS from VCAP as well as protecting against a
SYS short or if VCAP > VSYS.
Application Circuit
The typical application of the MAX38888 is shown in Figure 1.
CHARGE
500mA (MAX)
DISCHARGE
2.5A (MAX)
L1
1µH
VSC
2.7V (MAX)
1.5V (MIN)
CAP
10F
SUPERCAP
C2
22µF
R3
1.8MΩ
LX
SYS
R7
1MΩ
MAX38888
R8
1MΩ
R6
2.49MΩ
C1
22µF
FBCL
R2
402kΩ
MAIN
BATTERY
(REMOVABLE)
FBS
EN
R1
499kΩ
BACKUP
READY
BKUPB
RDY
FBCH
ENABLE
INPUT
VSYS
SYSTEM LOAD
3V (MIN)
GND
ISET
R4
20kΩ
R5
499kΩ
Figure 1. Typical Application
Supercapacitor Voltage Configuration
The maximum supercapacitor voltage is set using a resistor-divider from CAP to FBCH to GND. The recommended value
for R1 is 499kΩ. Because resistor tolerance will have direct effect on voltage accuracy, these resistors should have 1%
accuracy or better.
R2 + R3 = R1 × ((VCAPMAX / 0.5) − 1)
www.maximintegrated.com
Maxim Integrated | 10
MAX38888
2.5V to 5.0V, 0.5A/2.5A Reversible Buck/Boost
Regulator for Backup Power Applications
VCAP halts charging when VFBCH reaches 0.5V. The maximum supercapacitor voltage is where the supercapacitor will
remain after it is completely charged and ready for backup.
The minimum supercapacitor discharge voltage is set using a resistor-divider from CAP to FBCL to GND.
R3 = (R1 + R2) × ((VCAPMIN / 0.5) − 1)
FBCL prevents the supercapacitor from further discharge when VFBCL reaches 0.475V during a backup event in order to
preserve the remaining capacity for keeping alive a real-time clock, memory, or other low-level function. In this preserve
mode, the IC disconnects all circuitry from the supercapacitor and draws 2.5μA current from it.
In applications where SYS voltage needs to be boosted to higher levels, selecting VCAP min has to take into account duty
cycle limitation of the boosting phase, which is 80%. The MAX38888 detects when VSYS falls below VCAP. The device
will not enable if VSYS is below VCAP. Raising VSYS above the backup threshold re-initiates charging and backup.
System Voltage Configuration
The minimum system voltage is set using a resistor-divider from SYS to FBS to GND. The recommended value for R5 is
499kΩ. Because resistor tolerance will have direct effect on voltage accuracy, these resistors should have 1% accuracy
or better.
R6 = R5 × ((VSYSMIN / 0.5) − 1)
When VFBS is above 0.56V, the DC-DC regulator will draw power from the SYS pin to charge the supercapacitor to the
maximum voltage set by FBCH and be ready for backup. When the main battery is removed, VFBS drops to 0.5V and the
SYS pin is regulated to the programmed minimum voltage with up to 2A of CAP current.
Charge/Discharge Current Configuration
The peak inductor discharge current is set by placing a resistor from ISET to GND. The values of RISET resistor is
calculated by following formula:
IDISCHARGE = 2.5A × (20kΩ / RISET)
The supercapacitor charging current is internally set to 1/5 of the discharge current.
ICHARGE = 0.5A × (20kΩ / RISET)
the value of RISET between 20kΩ and 100kΩ is recommended to ensure accurate current compliance.
System Waveforms
The waveforms in Figure 2 represent system behavior of the MAX38888 in the Typical Application Circuit.
www.maximintegrated.com
Maxim Integrated | 11
MAX38888
2.5V to 5.0V, 0.5A/2.5A Reversible Buck/Boost
Regulator for Backup Power Applications
4V
3.36V
VSYS
3.18V
3V
0V
2.7V
VCAP
1.42V
0V
BKUPB
FBS ≤ 0.5V
0V
RDY
FBCH ≥ 0.5V
CHARGE
FBCL < 0.475V
LOW CURRENT
BACKUP
PRESERVE
Figure 2. System Waveforms
www.maximintegrated.com
Maxim Integrated | 12
MAX38888
2.5V to 5.0V, 0.5A/2.5A Reversible Buck/Boost
Regulator for Backup Power Applications
Applications Information
Capacitor Selection
Capacitors at the SYS and CAP pins reduce current peaks and increase efficiency. Ceramic capacitors are
recommended because they have the lowest equivalent series resistance (ESR), smallest size, and lowest cost. Choose
an acceptable dielectric such as X5R or X7R. Due to the ceramic capacitors' capacitance derating with DC bias, standard
22μF ceramic capacitors are recommended at both pins for most applications.
Supercapacitor Selection
When the power source supplying the VSYS voltage is removed, power to the output is provided by the MAX38888
operating in the back-up or boost mode of operation using the supercapacitor as its source. In order to ensure the
supply voltage stays in regulation, the amount of power the supercapacitor can deliver at its minimal voltage should be
greater than that required by the system. The MAX38888 will present a constant power load to the supercapacitor where
smaller current will be pulled out of the supercapacitor near its maximum VCAP voltage. However, current drawn from
the supercapacitor will increase as it discharges to maintain constant power at the load. The amount of energy required
in the backup mode will be the product of the constant backup power and time defined as backup time, tBACKUP.
The amount of energy available in the supercapacitor is calculated using the following formula:
/
E = 1 2 × CSCAP × (VCAPMAX2 − VCAPMIN2)(J)
The amount of energy required to complete the backup equals:
E = VSYS × ISYS × tBACKUP)(J)
where, ISYS will be the system load during backup.
Since the energy required at the system side during the backup event comes from the available energy in the
supercapacitor, assuming conversion efficiency η and given tBACKUP, the required CSCAP will be determined by the
following equation:
/
CSCAP = (2xVSYS × ISYS × tBACKUP) [(VCAPMAX2 – VCAPMIN2) × η](F)
www.maximintegrated.com
Maxim Integrated | 13
MAX38888
2.5V to 5.0V, 0.5A/2.5A Reversible Buck/Boost
Regulator for Backup Power Applications
VOLTAGE (V)
4
VSYS
3.36
3
2.7
VCAP
LOW IQ
1.5
0
CHARGING CAP
(BUCK)
IDLE
(NO SWITCHING)
BACKUP
(BOOST)
PRESERVE
(LOW CURRENT)
Figure 3. Charging/Discharging Waveforms
For example, in Figure 1 (Application Circuit), the minimum value of the supercapacitor required for 1s backup time,
assuming a 200mA system load and average efficiency of 93%, will be:
/
CSCAP ≥ (2 × 3.0V × 0.2A × 1s) [((2.7V)2 – (1.5V)2) × 0.93] = 256mF
Inductor Selection
The MAX38888 works with a 1μH inductor in most applications. In applications where lower peak currents are desired,
larger inductance may be used in order to reduce the ripple. The recommended inductance range is from 1μH to 4.7μH.
Select 4.7μH for higher RISET value (100kΩ). 1μH is not supported for a 100kΩ RISET value.
Status Flags
The MAX38888 has two dedicated pins to report the device status to the host processor. The ready output (RDY) will be
high when the supercapacitor is fully charged (i.e., FBCH > 0.5V). RDY is pulled low when FBCL < 0.475V. The other
status flag is the Backup Output (BKUPB), which will be held low when the part is in the backup mode (i.e., when FBS <
0.5V and FBCL > 0.5V). BKUPB is released high when FBCL < 0.475V or FBS > 0.56V. Both output pins are open-drain
type and require external pullup resistors. Recommended values for the pullup resistors are 1MΩ. The pins should be
pulled up to the SYS rail.
Enabling Device
The MAX38888 has a dedicated enable pin. The pin can either be driven by a digital signal, pulled up, or strapped to the
SYS rail.
PCB Layout Guidelines
Minimize trace lengths to reduce parasitic capacitance, inductance and resistance, and radiated noise. Keep the main
power path from SYS, LX, CAP, and PGND as tight and short as possible. Minimize the surface area used for LX since
this is the noisiest node. The trace between the feedback resistor-dividers should be as short as possible and should be
isolated from the noisy power path. Refer to the EV kit layout for best practices.
www.maximintegrated.com
Maxim Integrated | 14
MAX38888
2.5V to 5.0V, 0.5A/2.5A Reversible Buck/Boost
Regulator for Backup Power Applications
The PCB layout is important for robust thermal design. The junction-to-ambient thermal resistance of the package greatly
depends on the PCB type, layout, and pad connections. Using thick PCB copper and having the SYS, LX, CAP, and
PGND copper pours will enhance the thermal performance. The TDFN package has a large thermal pad under the
package, which creates excellent thermal path to PCB. This pad is electrically connected to PGND. Its PCB pad should
have multiple thermal vias connecting the pad to the internal PGND plane. Thermal vias should either be capped or have
small diameter to minimize solder wicking and voids.
Ordering Information
PART NUMBER
TEMP RANGE
PIN-PACKAGE
MAX38888ATD+
-40°C to +125°C
14 TDFN
FEATURES
Enable Input, Selectable Voltages and Currents
+ Denotes a lead(Pb)-free/RoHS-compliant package.
T Denotes tape-and-reel.
www.maximintegrated.com
Maxim Integrated | 15
MAX38888
2.5V to 5.0V, 0.5A/2.5A Reversible Buck/Boost
Regulator for Backup Power Applications
Revision History
REVISION
NUMBER
REVISION
DATE
PAGES
CHANGED
0
6/18
Initial release
—
1
7/18
Updated General Description and Benefits and Features
1
2
10/18
Updated General Description, Benefits and Features, Electrical
Characteristics
table, Typical Operating Characteristics, Detailed Description
3
7/19
Updated Supercapacitor Voltage Configuration section
9
4
12/19
Updated Enabling Device section
12
5
8/20
Updated Detailed Description
10
DESCRIPTION
1, 3–6, 9–12
For pricing, delivery, and ordering information, please visit Maxim Integrated’s online storefront at https://www.maximintegrated.com/en/storefront/storefront.html.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent
licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max
limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
© 2020 Maxim Integrated Products, Inc.
工商网监
湘ICP备2023018690号
