Click here for production status of specific part numbers.
MAX40002–MAX40005
MAX40012–MAX40015
nanoPower 4-Bump Comparator in Ultra-Tiny
0.73mm x 0.73mm WLP/SOT23 Packages
General Description
The MAX40002–MAX40005 and MAX40012–MAX40015
tiny, single comparators are ideal for a wide variety of
portable electronics applications such as cell phones,
media players, and notebooks that have extremely tight
board space and power constraints. These comparators
are offered in both, a miniature 4-bump wafer-level package (WLP) with a 0.73mm x 0.73mm footprint (as small as
two 0402 resistors) and a 5-pin SOT23 package.
This device family operates with a supply voltage range
from 1.7V to 5.5V (either VCC or external VREF), and
consumes only 500nA of supply current. These devices
have a wide input-voltage range of 0.1V to 5.5V, independent
of the supply voltage, and maintain high impedance at
the inputs even when powered down (VCC or external
VREF = 0V). They also feature internal filtering to provide
high RF immunity.
The MAX40002–MAX40003 and MAX40012–MAX40013
have open-drain outputs, while the MAX40004–MAX40005
and MAX40014–MAX40015 feature push-pull outputs. The
MAX40002/MAX40004 and MAX40012–MAX40014 have
noninverting inputs, while the MAX40003/MAX40005 and
MAX40013–MAX40015 have inverting inputs (see the
Selector Guide for more information).
These devices also come with an internal reference. The
reference voltage is preset at the factory and parts are
offered with the following voltage options: 0.2V, 0.5V, 0.9V
or 1.222V (see Ordering Information table).
These devices are fully specified over -40°C to +125°C
automotive temperature range.
Applications
●●
●●
●●
●●
●●
Mobile Devices
Portable Medical Devices
Portable Instrumentation
Notebook Computers
Electronic Toys
19-8574; Rev 8; 5/20
Benefits and Features
●● Tiny 0.73mm x 0.73mm, 4-Bump WLP and 5-Pin
SOT23 Packages Save Board Space
●● Ultra-Low 500nA Operating Current Preserves
Battery Power in Applications Where Comparator is
Constantly Monitoring
●● 1.7V to 5.5V Supply Range Allows Operation from
1.8V, 2.5V, 3V and 5V Systems
●● Input Voltage Range: 0.1V to 5.5V
●● External REF Range: 1.7V to 5.5V
●● Wide Variety of Factory-Trimmed Reference Voltages
Saves Space and Cost of External Reference:
• 0.2V, 0.5V, 0.9V, 1.222V
• 9µs Propagation Delay
●● -40°C to +125°C Specified Temperature Range
Ordering Information appears at end of data sheet.
MAX40002–MAX40005
MAX40012–MAX40015
nanoPower 4-Bump Comparator in Ultra-Tiny
0.73mm x 0.73mm WLP/SOT23 Packages
Absolute Maximum Ratings
Operating Temperature Range.......................... -40°C to +125°C
Junction Temperature.......................................................+150°C
Storage Temperature Range............................. -65°C to +150°C
Lead Temperature (soldering, 10s).................................. +300°C
Soldering Temperature (reflow).......................................... 260°C
VCC/REF to GND ...................................................-0.3V to +6V
IN to GND ................................................................-0.3V to +6V
OUT (Open-Drain) to GND ......................................-0.3V to +6V
OUT (Pushpull) to GND ..............................-0.3V to VCC + 0.3V
Continuous Current Into Any Input/Output........................±20mA
Continuous Power Dissipation (TA = +70°C)
4-Bump WLP (Derate 9.58mW/°C above +70°C).....766.4mW
5-Pin SOT (Derate 3.9mW/°C above +70°C.............312.6mW
Package Thermal Characteristics (Note 1)
WLP
Junction-to-Ambient Thermal Resistance (θJA)....104.41°C/W
SOT23
Junction-to-Ambient Thermal Resistance (θJA)......255.9°C/W
Junction-to-Ambient Thermal Resistance (θJC)...........81°C/W
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer
board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics
VCC/REF = 3.3V, RPULLUP = 100kΩ to VPULLUP = 3.3V, RL = ∞, CL = 20pF, TA = TMIN to TMAX. Typical values are at TA = +25°C,
unless otherwise noted. (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
5.5
V
POWER SUPPLY VOLTAGE
VCC/REF Supply Voltage
Range
VCC/VREF
1.7
VIN > 0, VOUT = low,
no output or reference load current,
VCC/REF Supply Current
ICC
0.5
TA = -40°C to +85°C
1.1
µA
VIN > 0, VOUT = low,
no output or reference load current,
1.3
TA = -40°C to +125°C
Power-Up Time
0.5
ms
COMPARATOR
Input Voltage Range
Input Offset Voltage
(For External VREF only)
(Note 3)
www.maximintegrated.com
VIN
TA = +25°C
0.1
VCC
+ 0.1
TA = -40°C to +125°C
0.1
VCC
Over VIN range,
VOS
TA = -40°C to +85°C
Over VIN range,
TA = -40°C to +125°C
0.5
V
27
mV
32
Maxim Integrated │ 2
MAX40002–MAX40005
MAX40012–MAX40015
nanoPower 4-Bump Comparator in Ultra-Tiny
0.73mm x 0.73mm WLP/SOT23 Packages
Electrical Characteristics (continued)
VCC/REF = 3.3V, RPULLUP = 100kΩ to VPULLUP = 3.3V, RL = ∞, CL = 20pF, TA = TMIN to TMAX. Typical values are at TA = +25°C,
unless otherwise noted. (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
Input Offset Drift (For External
VREF Only) (Note 3)
Input Hysteresis
VHYS
Input Bias Current
(Note 4)
8
Over VIN range, TA = -40°C to +85°C
20
Over VIN range, TA = -40°C to +125°C
Input Leakage Current
(VCC/REF = 0) (MAX40002 and
MAX40003)
No supply voltage, TA = -40°C to +125°C
Input Capacitance
Either input, over VCM range
Power Supply Rejection Ratio
UNITS
320
µV/°C
mV
30
90
No supply voltage, TA = -40°C to +85°C
PSRR
MAX
20
30
80
0.4
DC, internal VREF
40
DC, external VREF
45
nA
nA
pF
dB
Output Voltage Swing Low
VOL
Sinking 2mA, measured relative with GND
0.4
V
Output Voltage Swing High
VOH
Sourcing 1mA, measured with relative
with VCC
0.4
V
Open-drain only, VCC/REF = 1.8V, VO =
5.5V, TA = -40°C to +125°C
100
nA
Output Leakage Current
Propagation Delay
(Note 5)
IO-LKG
tPD
Rise Time
tR
Fall Time
tF
www.maximintegrated.com
100mV overdrive,
push-pull OUT = low to high
25
100mV overdrive, open-drain,
RPU = 100kΩ, OUT = low to high
25
100mV overdrive, both push-pull and
open-drain, OUT= high to low
9
20mV overdrive,
push-pull OUT = low to high
50
20mV overdrive, open-drain,
RPU = 100kΩ, OUT = low to high
55
20mV overdrive, both push-pull and
open-drain, OUT = high to low
45
Push-pull output
800
ns
200
ns
µs
Maxim Integrated │ 3
MAX40002–MAX40005
MAX40012–MAX40015
nanoPower 4-Bump Comparator in Ultra-Tiny
0.73mm x 0.73mm WLP/SOT23 Packages
Electrical Characteristics (continued)
VCC/REF = 3.3V, RPULLUP = 100kΩ to VPULLUP = 3.3V, RL = ∞, CL = 20pF, TA = TMIN to TMAX. Typical values are at TA = +25°C,
unless otherwise noted. (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
200
212
mV
INTERNAL REFERENCE VOLTAGE
Switching Threshold Voltage
(Note 6)
VREF-INT
TA = +25°C
MAX4000_ _ _ _02+
188
TA = -40°C to
+85°C
MAX4000_ _ _ _02+
177
223
mV
TA = -40°C to
+125°C
MAX4000_ _ _ _02+
174
226
mV
TA = +25°C
MAX4000_ _ _ _05+
485
515
mV
TA = -40°C to
+85°C
MAX4000_ _ _ _05+
468
532
mV
TA = -40°C to
+125°C
MAX4000_ _ _ _05+
463
537
mV
TA = +25°C
MAX4001_ _ _ _ 09+
882
918
mV
TA = -40°C to
+85°C
MAX4001_ _ _ _ 09+
873
927
mV
MAX4001_ _ _ _ 09+
(WLP)
873
927
MAX4001_ _ _ _ 09+
(SOT23)
864
936
TA =+25°C
MAX4000_ _ _ _ 12+
1200
TA = -40°C to
+85°C
MAX4000_ _ _ _ 12+
TA = -40°C to
+125°C
MAX4000_ _ _ _ 12+
TA = -40°C to
+125°C
500
900
mV
1222
1244
mV
1169
1275
mV
1157
1287
mV
Note
Note
Note
Note
2: All devices are 100% production tested at TA = +25°C. Temperature limits are guaranteed by design.
3: VOS is the average of the positive and negative trip points minus VREF.
4: Hysteresis is the input voltage difference between the two switching points.
5: Overdrive (VOD) is the voltage above or below the switching points. The input starts at 100mV below the trip point and use
50% input to 50% output for timing. VIN = VREF_INT±VOD±VHYS.
Note 6: Switching Threshold Voltages include the offset voltage of the comparator and the internal reference.
www.maximintegrated.com
Maxim Integrated │ 4
MAX40002–MAX40005
MAX40012–MAX40015
nanoPower 4-Bump Comparator in Ultra-Tiny
0.73mm x 0.73mm WLP/SOT23 Packages
Typical Operating Characteristics
VCC/REF = 3.3V, VGND = 0V, TA =25°C, unless otherwise noted.
SUPPLY CURRENT vs.
SUPPLY VOLTAGE
5
0.8
TA = +85°C
0.6
0.4
TA = +25°C
0.2
TA = -40°C
1.5
2
5
VCC = 1.8V
0.6
1
10
100
0.5
0.4
0.3
OUTPUT VOLTAGE LOW vs.
SINK CURRENT (TA = +25°C)
1.2
toc3a
VCC = 3.3V
0.7
0.1
OUTPUT TRANSISTION FREQUENCY (kHz)
VCC = 5V
0.8
VCC = 1.8V
2
5.5
OUTPUT VOLTAGE LOW (V)
OUTPUT VOLTAGE LOW (V)
0.9
VCC = 5V
VCC = 3.3V
3
0
2.5
3
3.5
4
4.5
SUPPLY VOLTAGE (V)
OUTPUT VOLTAGE LOW vs.
SINK CURRENT (TA = -40°C)
1
4
1
VOUT = LOW
0
toc02
VREF-INT = 0.2V
TA = +125°C
1
SUPPLY CURRENT vs.
OUTPUT TRANSITION FREQUENCY
6
SUPPLY CURRENT (μA)
SUPPLY CURRENT (μA)
1.2
toc01
0.2
1
VCC = 3.3V
0.8
toc3b
VCC = 5V
VCC = 1.8V
0.6
0.4
0.2
0.1
0
0
60
OUTPUT VOLTAGE LOW vs.
SINK CURRENT(TA = +125°C)
1.2
OUTPUT VOLTAGE LOW (V)
20
40
SINK CURRENT (mA)
80
VCC = 5V
1
VCC = 3.3V
0.8
VCC = 1.8V
0.6
0.4
0.2
0
20
40
SINK CURRENT (mA)
www.maximintegrated.com
60
20
40
SINK CURRENT (mA)
60
OUTPUT VOLTAGE HIGH vs.
SOURCE CURRENT(TA = -40°C)
2
80
toc4a
VCC = 5V
VCC = 3.3V
1.5
VCC = 1.8V
1
0.5
0
0
0
2.5
toc3c
OUTPUT VOLTAGE HIGH(VCC - VOH,V)
0
0
20
40
60
SOURCE CURRENT (mA)
80
Maxim Integrated │ 5
MAX40002–MAX40005
MAX40012–MAX40015
nanoPower 4-Bump Comparator in Ultra-Tiny
0.73mm x 0.73mm WLP/SOT23 Packages
Typical Operating Characteristics (continued)
OUTPUT VOLTAGE HIGH vs.
SOURCE CURRENT(TA = +25°C)
OUTPUT VOLTAGE HIGH (VCC - VOH,V)
2.5
OUTPUT VOLTAGE HIGH vs.
SOURCE CURRENT (TA = +125°C)
3
VCC = 3.3V
1.5
VCC = 5V
2
VCC = 3.3V
VCC = 5V
1.5
1
VCC = 1.8V
0.5
VCC = 1.8V
1
0.5
0
0
20
40
SOURCE CURRENT (mA)
INPUT BIAS CURRENT
vs. INPUT BIAS VOLTAGE
2
60
0
PROPAGATION DELAY (μs)
1.5
1
PROPAGATION DELAY vs.
TEMPERATURE
31
50
toc06
VCC = 5.0V
29
27
VCC = 3.3V
25
23
VCC = 1.8V
21
19
VREF-INT = 0.2V
VOD = ±100mV
17
15
0
0.05
0.1
0.15
0.2
0.25
INPUT BIAS VOLTAGE (V)
PROPAGATION DELAY vs.
INPUT OVERDRIVE
160
140
0.3
VREF-INT = 0.2V
80
VCC = 1.8V
60
VCC = 3.3V
40
VCC = 5.0V
20
40
www.maximintegrated.com
60 80 100 120 140 160 180 200
INPUT OVERDRIVE (mV)
0
25
50
75
TEMPERATURE (°C)
100
125
toc08
VREF-INT = 0.2V
VOD = ±200mV
28
26
24
22
20
0
-25
PROPAGATION DELAY vs.
SUPPLY VOLTAGE
30
PROPAGATION DELAY (μs)
100
-50
32
toc07
120
20
20
30
40
SOURCE CURRENT (mA)
33
VREF-INT = 0.2V
0
10
35
toc05
0.5
PROPAGATION DELAY (μs)
toc4c
2.5
2
0
INPUT BIAS CURRENT (nA)
toc4b
OUTPUT VOLTAGE HIGH(VCC - VOH,V)
VCC/REF = 3.3V, VGND = 0V, TA =25°C, unless otherwise noted.
1.5
2.5
3.5
4.5
SUPPLY VOLTAGE (V)
5.5
Maxim Integrated │ 6
MAX40002–MAX40005
MAX40012–MAX40015
nanoPower 4-Bump Comparator in Ultra-Tiny
0.73mm x 0.73mm WLP/SOT23 Packages
Typical Operating Characteristics (continued)
VCC/REF = 3.3V, VGND = 0V, TA =25°C, unless otherwise noted.
OUTPUT RESPONSE LOW TO HIGH
(VREF-INT = 0.2V, CLOAD = 20pF)
OUTPUT RESPONSE HIGH TO LOW
(VREF-INT = 0.2V, CLOAD = 20pF)
toc09
toc10
VIN
VIN
(100mV/div)
(100mV/div)
VOUT
(2V/div)
VOUT
(2V/div)
4μs/div
10μs/div
1kHz FREQUENCY RESPONSE
(VREF
INT = 0.2V, CLOAD = 20pF)
-
OUTPUT RESPONSE TO
SUPPLY VOLTAGE TRANSIENT
toc11
toc12
VCC
3.2V
(200mV/div)
3V
VIN = VTH + 1mV
VOUT
(2V/div)
VIN
(100mV/div)
0V
VOUT
(2V/div)
VIN = VTH + 10mV
VOUT
(2V/div)
0V
VIN = VTH + 20mV
VOUT
(2V/div)
0V
1ms/div
200μs/div
POWER-UP/POWER-DOWN RESPONSE
(VIN = 300mV)
toc13
210
206
VCC
(2V/div)
204
TRIP POINT (mV)
0V
VOUT
(2V/div)
202
200
198
196
194
VREF-INT = 0.2V
VCC = 3.3V ±100mV
192
0V
190
1ms/div
toc14
UPPER
TRIP POINT
208
3.3V
www.maximintegrated.com
POWER-SUPPLY REJECTION
FOR NO FALSE TRIGGERING
10
100
LOWER
TRIP POINT
1000
10000
FREQUENCY (Hz)
100000 1000000
Maxim Integrated │ 7
MAX40002–MAX40005
MAX40012–MAX40015
nanoPower 4-Bump Comparator in Ultra-Tiny
0.73mm x 0.73mm WLP/SOT23 Packages
Pin Configurations
TOP VIEW
MAX40002–MAX40005 AND
MAX40012–MAX40015
A
1
2
OUT
IN
VCC /
REF
GND
+
B
WLP
VCC/
1
REF
GND 2
+
MAX40002–
MAX40005
AND
MAX40012–
MAX40015
N.C. 3
5 OUT
4 IN
SOT-23
Pin Description
PIN
WLP
SOT23
NAME
FUNCTION
Comparator Output. OUT is an Open-Drain Output (MAX40002/MAX40003 and MAX40012/
MAX40013) or Push-Pull Output (MAX40004/MAX40005 and MAX40014/MAX40015). For the
open-drain versions, connect a pullup resistor from OUT to any pullup voltage up to 5.5V for
proper operation.
A1
5
OUT
A2
4
IN
Comparator Input. The MAX40002/MAX40004 and MAX40012/MAX40014 have a noninverting
input. The MAX40003/MAX40005 and MAX40013/MAX40015 have an inverting input (see Input
Stage Circuitry for more information).
VCC Supply Voltage/External REF Voltage Input.
VCC/REF is the supply voltage for devices with internal voltage reference (0.2V, 0.5V, 0.9V, 1.2V
internal references. VCC/REF is the external reference input as well as the supply voltage for
devices without the internal reference. Bypass VCC/REF with a 0.1µF capacitor to GND as close
to the device pin as possible.
B1
1
VCC/REF
B2
2
GND
Ground.
—
3
N.C.
No Connect. Not internally connected.
www.maximintegrated.com
Maxim Integrated │ 8
MAX40002–MAX40005
MAX40012–MAX40015
nanoPower 4-Bump Comparator in Ultra-Tiny
0.73mm x 0.73mm WLP/SOT23 Packages
Detailed Description
The MAX40002–MAX40005 and MAX40012/MAX40015
are extremely small comparators ideal for compact, lowcurrent and low-voltage applications.
The devices (with internal reference voltage) consume
only 500nA (typ). Low-voltage operating capability makes
the MAX40002–MAX40005 and MAX40012/MAX40015
extremely attractive to long-life, battery-operated applications. These applications can now use a single digital
power supply rail used to power the new generation of
microcontrollers. All parts are available in either tiny 4-bump
WLP or 5-pin SOT23.
Input-Stage Circuitry
Non-inverting inputs are available on the MAX40002/
MAX40004 and MAX40012/MAX40014 and their associated outputs assert high when the input voltage is
greater than the voltage reference. Inverting inputs are
available on the MAX40003/MAX40005 and MAX40013/
MAX40015 and their associated outputs assert low when
the input voltage is greater than the voltage reference.
The MAX40002–MAX40005 and MAX40012/MAX40015
incorporate an innovative input-stage architecture that
allows their input voltage to exceed VCC by several volts (limited only by Absolute Maximum Ratings).
This is unlike traditional comparators that have an
input ESD diode clamp between the input and VCC,
limiting this maximum overvoltage to about 0.3V.
The device architecture maintain a high input impedance
to input signals even when the device power-supply voltage
is completely turned off (VCC or VREF taken to 0V). This
greatly benefits flexible power-saving schemes to be
easily implemented in advanced battery-operated devices.
On-chip filtering provides immunity from any RF noise being
picked up by input traces. These devices feature an internal
temperature-compensated, low-power voltage references
for improved PSRR.
Applications Information
Bypassing VCC/REF
Place a 0.1µF capacitor between VCC/REF and GND as
close to the device as possible. During a switching event,
all comparators draw a current-spike from their power
supply rails. This current-spike is minimized by the use
of an internal Break-Before-Make design implementation.
Hysteresis Operation
The MAX40002–MAX40005 and MAX40012/MAX40015
feature 8mV (typ) internal hysteresis for noise immunity and glitch-free operation. If additional hysteresis is
needed, an external positive feedback network can be
easily implemented on the MAX40002/MAX40004 and
MAX40012/MAX40014 with noninverting input devices
(both internal and external reference). Additional external
hysteresis is not recommended for the MAX40003/
MAX40005 and MAX40013/MAX40015 (with external
reference) due to possible crossover current related noise
problems. Additional external hysteresis is not possible on
the MAX40003/MAX40005 and MAX40013/MAX40015
(internal reference) because the noninverting input of the
comparator is not externally accessible.
Adaptive Signal Level Detector
The MAX40002/MAX40012 and MAX40003/MAX40013
can be used as an adaptive signal-level detector. Feed a DAC output voltage to REF and connect the input to a variable signal level. As the
DAC output voltage is varied from 1.7V to 5.5V, a corresponding signal level threshold detector circuit is implemented (Figure 1).
VDD
MAX40002A_ _
MAX40003A_ _
AND
MAX40012A_ _
MAX40013A_ _
Output Stage Structure
The MAX40002–MAX40003 and MAX40012/MAX40013
have open-drain output structures that allow them to interface to logic circuitry operating from supply voltages other
than the one supplied to the part. These devices require an
external pullup resistor or current-source for proper operation. Most microcontroller digital input ports can be readily
programmed to include these pullup sources.
The MAX40004–MAX40005 and MAX40014/MAX40015
have a push-pull type output stage that can both sink and
source current, eliminating the need for an external pullup
resistor.
www.maximintegrated.com
REF
DAC
INTERNAL
PULL-UP
OUT
IN
I/O
MICRO
CONTROLLER
Figure 1. Adaptive Signal-Level Detector
Maxim Integrated │ 9
MAX40002–MAX40005
MAX40012–MAX40015
nanoPower 4-Bump Comparator in Ultra-Tiny
0.73mm x 0.73mm WLP/SOT23 Packages
Table 1. How Devices Behave Under Various Input Voltage Conditions
PART
MAX40002,
MAX40004,
MAX40012,
MAX40014
MAX40003,
MAX40005,
MAX40013,
MAX40015
MAX40002,
MAX40004,
MAX40012,
MAX40014
MAX40003,
MAX40005,
MAX40013,
MAX40015
VREF
INPUT POLARITY
INPUT VOLTAGE CONDITIONS
ACTION AT OUTPUT
VIN > VREF
Output goes high
VIN < VREF
Output goes low
VIN > VREF
Output goes low
VIN < VREF
Output goes high
VIN > VREF_INT
Output goes high
VIN < VREF_INT
Output goes low
VIN > VREF_INT
Output goes low
VIN < VREF_INT
Output goes high
Noninverting
External
Inverting
Noninverting
Internal
www.maximintegrated.com
Inverting
Maxim Integrated │ 10
MAX40002–MAX40005
MAX40012–MAX40015
nanoPower 4-Bump Comparator in Ultra-Tiny
0.73mm x 0.73mm WLP/SOT23 Packages
Typical Operating Circuits
VDD
MAX40002ANS
MAX40002AUK
MAX40012ANS
MAX40012AUK
1.7V
TO
5.5V
REF
INTERNAL
PULL-UP
OUT
I/O
REF
REF
OUT
MICRO
CONTROLLER
IN
OUT
MICRO
CONTROLLER
REF
VDD
OUT
I/O
MICRO
CONTROLLER
IN
VCC = 1.7V
TO 5.5V
VCC = 1.7V
TO 5.5V
VDD
MAX40002ANS_ _
MAX40002AUK_ _
MAX40012ANS_ _
MAX40012AUK_ _
OUT
INTERNAL
PULL-UP
REF
I/O
OUT
MICRO
CONTROLLER
IN
VDD
MAX40003ANS_ _
MAX40003AUK_ _
MAX40013ANS_ _
MAX40013AUK_ _
INTERNAL
PULL-UP
REF
I/O
MICRO
CONTROLLER
IN
VCC = 1.7V
TO 5.5V
VCC = 1.7V
TO 5.5V
MAX40004ANS_ _
MAX40004AUK_ _
MAX40014ANS_ _
MAX40014AUK_ _
MAX40005ANS_ _
MAX40005AUK_ _
MAX40015ANS_ _
MAX40015AUK_ _
VDD
REF
VDD
REF
OUT
IN
I/O
MAX40005ANS
MAX40005AUK
MAX40015ANS
MAX40015AUK
1.7V
TO
5.5V
I/O
INTERNAL
PULL-UP
IN
VDD
MAX40004ANS
MAX40004AUK
MAX40014ANS
MAX40014AUK
1.7V
TO
5.5V
1.7V
TO
5.5V
MICRO
CONTROLLER
IN
VDD
MAX40003ANS
MAX40003AUK
MAX40013ANS
MAX40013AUK
OUT
I/O
MICRO
CONTROLLER
IN
I/O
MICRO
CONTROLLER
MAX40002–MAX40003 AND MAX40012–MAX40013 HAVE OPEN-DRAIN OUTPUT,
MAX40004–MAX40005 AND MAX40014–MAX40015 HAVE PUSHPULL OUTPUT,
MAX40002/MAX40004 AND MAX40012/MAX40014 HAVE NONINVERTING INPUT,
MAX40003/MAX40005 AND MAX40013/MAX40015 HAVE INVERTING INPUT,
THE “_ _” INDICATES INTERNAL REFERENCE VOLTAGE
www.maximintegrated.com
Maxim Integrated │ 11
MAX40002–MAX40005
MAX40012–MAX40015
nanoPower 4-Bump Comparator in Ultra-Tiny
0.73mm x 0.73mm WLP/SOT23 Packages
Selector Guide
INTERNAL REFERENCE
VOLTAGE (V)
INPUT
OUTPUT
MAX40002ANS+T
—
Noninverting
OPEN-DRAIN
+I
MAX40002AUK+T*
—
Noninverting
OPEN-DRAIN
+AMHU
MAX40002ANS02+T
0.2
Noninverting
OPEN-DRAIN
+M
MAX40002AUK02+T
0.2
Noninverting
OPEN-DRAIN
+AMHV
MAX40002ANS05+T*
0.5
Noninverting
OPEN-DRAIN
+N
MAX40002AUK05+T*
0.5
Noninverting
OPEN-DRAIN
+AMHW
MAX40002ANS12+T
1.2
Noninverting
OPEN-DRAIN
+P
MAX40002AUK12+T*
1.2
Noninverting
OPEN-DRAIN
+AMHY
MAX40003ANS+T*
—
Inverting
OPEN-DRAIN
+J
MAX40003AUK+T*
—
Inverting
OPEN-DRAIN
+AMHZ
MAX40003ANS02+T
0.2
Inverting
OPEN-DRAIN
+Q
MAX40003AUK02+T*
0.2
Inverting
OPEN-DRAIN
+AMIA
MAX40003ANS05+T*
0.5
Inverting
OPEN-DRAIN
+R
MAX40003AUK05+T*
0.5
Inverting
OPEN-DRAIN
+AMIB
MAX40003ANS12+T
1.2
Inverting
OPEN-DRAIN
+T
MAX40003AUK12+T*
1.2
Inverting
OPEN-DRAIN
+AMID
MAX40004ANS+T*
—
Noninverting
PUSHPULL
+K
MAX40004AUK+T*
—
Noninverting
PUSHPULL
+AMIE
MAX40004ANS02+T
0.2
Noninverting
PUSHPULL
+W
MAX40004AUK02+T*
0.2
Noninverting
PUSHPULL
+AMIF
MAX40004ANS05+T*
0.5
Noninverting
PUSHPULL
+X
MAX40004AUK05+T*
0.5
Noninverting
PUSHPULL
+AMIG
MAX40004ANS12+T*
1.2
Noninverting
PUSHPULL
+U
MAX40004AUK12+T*
1.2
Noninverting
PUSHPULL
+AMIJ
MAX40005ANS+T
—
Inverting
PUSHPULL
+L
MAX40005AUK+T*
—
Inverting
PUSHPULL
+AMIK
MAX40005ANS02+T
0.2
Inverting
PUSHPULL
+Z
MAX40005AUK02+T*
0.2
Inverting
PUSHPULL
+AMIL
MAX40005ANS05+T
0.5
Inverting
PUSHPULL
+1
MAX40005AUK05+T*
0.5
Inverting
PUSHPULL
+AMIM
MAX40005ANS12+T*
1.2
Inverting
PUSHPULL
+V
MAX40005AUK12+T*
1.2
Inverting
PUSHPULL
+AMIO
MAX40012ANS09+T*
0.9V
Noninverting
OPEN-DRAIN
+4
+AMIS
PART NUMBER
TOP MARK
MAX40012AUK09+T*
0.9V
Noninverting
OPEN-DRAIN
MAX40013ANS09+T*
0.9V
Inverting
OPEN-DRAIN
+5
MAX40013AUK09+T*
0.9V
Inverting
OPEN-DRAIN
+AMIT
MAX40014ANS09+T
0.9V
Noninverting
PUSHPULL
+6
MAX40014AUK09+T
0.9V
Noninverting
PUSHPULL
+AMIU
MAX40015ANS09+T*
0.9V
Inverting
PUSHPULL
+7
MAX40015AUK09+T*
0.9V
Inverting
PUSHPULL
+AMIV
*Future product—contact factory for availability.
www.maximintegrated.com
Maxim Integrated │ 12
MAX40002–MAX40005
MAX40012–MAX40015
nanoPower 4-Bump Comparator in Ultra-Tiny
0.73mm x 0.73mm WLP/SOT23 Packages
Ordering Information
PART
Chip Information
TEMP RANGE
PIN-PACKAGE
MAX40002ANS+T
-40°C to +125°C
4 WLP
MAX40002ANS_ _+T
-40°C to +125°C
4 WLP
MAX40002AUK+T*
-40°C to +125°C
5 SOT23
MAX40002AUK_ _+T
-40°C to +125°C
5 SOT23
MAX40003ANS+T*
-40°C to +125°C
4 WLP
MAX40003ANS_ _+T
-40°C to +125°C
4 WLP
MAX40003AUK+T*
-40°C to +125°C
5 SOT23
MAX40003AUK_ _+T*
-40°C to +125°C
5 SOT23
MAX40004ANS+T*
-40°C to +125°C
4 WLP
MAX40004ANS_ _+T
-40°C to +125°C
4 WLP
MAX40004AUK+T*
-40°C to +125°C
5 SOT23
MAX40004AUK_ _+T*
-40°C to +125°C
5 SOT23
MAX40005ANS+T
-40°C to +125°C
4 WLP
MAX40005ANS_ _+T
-40°C to +125°C
4 WLP
MAX40005AUK+T
-40°C to +125°C
5 SOT23
MAX40005AUK_ _+T*
-40°C to +125°C
5 SOT23
MAX40012ANS09+T*
-40°C to +125°C
4 WLP
MAX40013ANS09+T*
-40°C to +125°C
4 WLP
MAX40014ANS09+T
-40°C to +125°C
4 WLP
MAX40015ANS09+T*
-40°C to +125°C
4 WLP
MAX40012AUK09+T*
-40°C to +125°C
5 SOT23
MAX40013AUK09+T*
-40°C to +125°C
5 SOT23
MAX40014AUK09+T
-40°C to +125°C
5 SOT23
MAX40015AUK09+T*
-40°C to +125°C
5 SOT23
PROCESS: BiCMOS
+Denotes a lead(Pb)-free/RoHS-compliant package.
T = Tape and reel.
*Future product—contact factory for availability.
The “_ _” are placeholders for internal reference voltage level.
For example, the MAX40002ANS05+T has an onboard 0.5V
reference voltage.
Devices without “_ _” use external reference voltage as supply
voltage.
www.maximintegrated.com
Maxim Integrated │ 13
MAX40002–MAX40005
MAX40012–MAX40015
nanoPower 4-Bump Comparator in Ultra-Tiny
0.73mm x 0.73mm WLP/SOT23 Packages
Package Information
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”,
“#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing
pertains to the package regardless of RoHS status.
PACKAGE TYPE
PACKAGE CODE
OUTLINE NO.
LAND PATTERN NO.
4 WLP
N40C0+1
21-100103
Refer to Application Note AN1891
5 SOT23
U5+1
21-0057
90-0174
Pin 1
Indicator
E
1
COMMON DIMENSIONS
see Note 7
Marking
A
A
A1
0.30 REF
A2
AAAA
D
0.040 BASIC
0.22 0.03
A3
b
0.728
0.728
D
TOP VIEW
A3
E
SIDE VIEW
D1
A1
A
E1
0.35 BASIC
0.35 BASIC
0.175 BASIC
SD
S
0.025
0.025
0.35 BASIC
e
A2
0.50 MAX
0.17 0.03
SE
0.175 BASIC
DEPOPULATED BUMPS:
NONE
0.05 S
FRONT VIEW
E1/e
SE
B
B
NOTES:
1. Terminal pitch is defined by terminal center to center value.
2. Outer dimension is defined by center lines between scribe lines.
3. All dimensions in millimeter.
4. Marking shown is for package orientation reference only.
5. Tolerance is ± 0.02 unless specified otherwise.
6. All dimensions apply to PbFree (+) package codes only.
7. Front - side finish can be either Black or Clear.
SD D1
A
1
2
A
BOTTOM VIEW
- DRAWING NOT TO SCALE -
www.maximintegrated.com
b
0.05 M
maxim
integrated
S AB
TITLE
TM
PACKAGE OUTLINE 4 BUMPS
THIN WLP PKG. 0.35 mm PITCH, N40C0+1
APPROVAL
DOCUMENT CONTROL NO.
21-100103
REV.
B
1
1
Maxim Integrated │ 14
MAX40002–MAX40005
MAX40012–MAX40015
nanoPower 4-Bump Comparator in Ultra-Tiny
0.73mm x 0.73mm WLP/SOT23 Packages
Package Information (continued)
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”,
“#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing
pertains to the package regardless of RoHS status.
maxim
integrated
www.maximintegrated.com
TM
Maxim Integrated │ 15
MAX40002–MAX40005
MAX40012–MAX40015
nanoPower 4-Bump Comparator in Ultra-Tiny
0.73mm x 0.73mm WLP/SOT23 Packages
Revision History
REVISION
NUMBER
REVISION
DATE
PAGES
CHANGED
0
3/17
Initial release
1
4/17
Updated Selector Guide and Ordering Information tables to remove future product
status from MAX40002AUK02+T, MAX40005ANS+T, and MAX40005AUK+T
11, 12
2
8/17
Updated Electrical Characteristics table and Selector Guide
2–4, 11
3
9/17
Removed future product asterisk from MAX40002ANS+T in Ordering Information and
Selector Guide tables
11, 12
4
11/17
Updated Electrical Characteristics table and Selector Guide
2–4, 11
5
12/18
Updated Selector Guide and removed package outline drawing
11, 13
6
11/19
Updated part numbers in data sheet title and throughout document
1–14
7
1/20
Updated Electrical Characteristics, Selector Guide, and Ordering Information
4, 12, 13
8
5/20
Updated Electrical Characteristics, Selector Guide, Ordering Information, and Package Information
4, 12–15
DESCRIPTION
—
For pricing, delivery, and ordering information, please visit Maxim Integrated’s online storefront at https://www.maximintegrated.com/en/storefront/storefront.html.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits)
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
© 2020 Maxim Integrated Products, Inc. │ 16