19-3570; Rev 1; 6/05
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
The MAX4030E/MAX4031E unity-gain stable op amps
combine high-speed performance, rail-to-rail outputs,
and ±15kV ESD protection. Targeted for applications
where an input or an output is exposed to the outside
world, such as video and communications, these
devices are compliant with International ESD
Standards: ±15kV IEC 1000-4-2 Air-Gap Discharge,
±8kV IEC 1000-4-2 Contact Discharge, and the ±15kV
Human Body Model.
The MAX4030E/MAX4031E operate from a single 5V
supply and consume only 12mA of quiescent supply
current per amplifier while achieving a 144MHz -3dB
bandwidth, 20MHz 0.1dB gain flatness, and a 115V/µs
slew rate. The MAX4031E provides individual shutdown
control for each of the amplifiers.
The dual MAX4030E is available in 8-pin µMAX® and SO
packages, and the triple MAX4031E is available in 14-pin
TSSOP and SO packages. All devices are specified over
the -40°C to +85°C extended temperature range.
Features
♦ ESD-Protected Video Inputs and Outputs
±15kV – Human Body Model
±8kV – IEC 1000-4-2 Contact Discharge
±15kV – IEC 1000-4-2 Air-Gap Discharge
♦ 5V Single-Supply Operation
♦ 0.1µA Low-Power Shutdown Mode (MAX4031E)
♦ Input Common-Mode Range Extends to Ground
♦ 2VP-P Large-Signal -3dB BW > 50MHz
♦ Directly Drives 150Ω Loads
♦ Low Differential Gain/Phase: 0.2%/0.2°
♦ -40°C to +85°C Extended Temperature Range
♦ Compact 8-Pin µMAX and 14-Pin TSSOP
Packages
Applications
Set-Top Boxes
Notebooks
Standard Definition
Television (SDTV)
Projectors
Ordering Information
TEMP RANGE
PIN-PACKAGE
Security Video Systems
MAX4030EEUA
PART
-40°C to +85°C
8 µMAX
Enhanced Television
(ETV)
Camcorders
MAX4030EESA
-40°C to +85°C
8 SO
MAX4031EEUD
-40°C to +85°C
14 TSSOP
High-Definition
Television (HDTV)
Portable DVD Players
MAX4031EESD
-40°C to +85°C
14 SO
Digital Still Cameras
µMAX is a registered trademark of Maxim Integrated Products, Inc.
Pin Configurations
Typical Operating Circuit
5V
TOP VIEW
0.1µF
OUTA
1
8 VCC
INA-
2
7
INA+
3
MAX4030E
GND 4
µMAX/SO
OUTB
6
INB-
5
INB+
SHDNA 1
14 OUTC
SHDNC
2
13 INC-
SHDNB
3
12 INC+
75Ω
75Ω
VCC 4
MAX4031E
INA+ 5
MAX4030E
MAX4031E
IN_+
OUT
Zo = 75Ω
11 GND
75Ω
10 INB+
INA- 6
9
INB-
OUTA 7
8
OUTB
200Ω
200Ω
TSSOP/SO
VIDEO LINE DRIVER
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX4030E/MAX4031E
General Description
MAX4030E/MAX4031E
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
ABSOLUTE MAXIMUM RATINGS
(All voltages referenced to GND, unless otherwise noted.)
VCC ...........................................................................-0.3V to +6V
IN_-, IN_+, OUT_, SHDN_ ..........................-0.3V to (VCC + 0.3V)
Current into IN_-, IN_+, SHDN..........................................±20mA
Output Short-Circuit Duration to VCC or GND ............Continuous
Continuous Power Dissipation (TA = +70°C)
8-Pin µMAX (derate 4.5mW/°C above +70°C) .............362mW
8-Pin SO (derate 5.9mW/°C above +70°C)..................471mW
14-Pin TSSOP (derate 9.1mW/°C above +70°C) .........727mW
14-Pin SO (derate 8.3mW/°C above +70°C)................667mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature .....................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(VCC = 5V, VCM = 0V, VOUT_ = VCC/2, SHDN_ = VCC, RL = ∞ to VCC/2, TA = TMIN to TMAX, unless otherwise noted. Typical values are
at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
Operating Supply Voltage Range
VCC
Quiescent Current (per Amplifier)
ICC
Shutdown Current (per Amplifier)
ISHDN
Input Common-Mode Voltage
VCM
Input Offset Voltage
VOS
CONDITIONS
Guaranteed by PSRR
MIN
TYP
4.5
SHDN_ = GND (MAX4031E)
Guaranteed by CMRR
UNITS
5.5
V
12
22
mA
0.1
10
µA
VCC 2.25
V
0
TA = +25°C
MAX
5
TA = -40°C to +85°C
13
26
mV
Input Offset Voltage Matching
∆VOS
2.6
mV
Input Offset Voltage Tempco
TCVOS
31
µV/°C
Input Bias Current
IB
0.01
Input Offset Current
IOS
0.01
1
µA
µA
Input Resistance
RIN
1
GΩ
Common-Mode Rejection Ratio
CMRR
GND ≤ VCM ≤ VCC - 2.25V
50
70
dB
Power-Supply Rejection Ratio
PSRR
4.5V ≤ VCC ≤ 5.5V
40
60
dB
0.5V ≤ VOUT_ ≤ 4.5V, RL = 2kΩ to VCC/2
Open-Loop Gain
AVOL
0.6V ≤ VOUT_ ≤ 4.4V, RL = 150Ω to VCC/2
50
70
0.4V ≤ VOUT_ ≤ 3.5V, RL = 150Ω to GND
50
70
RL = 2kΩ to VCC/2
Output Voltage Swing
VOUT_
RL = 150Ω to VCC/2
RL = 150Ω to GND
Output Short-Circuit Current
SHDN_ Logic Threshold
SHDN_ Logic Input Current
2
80
VCC - VOH
0.05
dB
VOL - GND
0.05
VCC - VOH
0.15
0.4
VOL - GND
0.15
0.4
VCC - VOH
0.3
0.8
VOL - GND
0.01
0.05
ISC
Sinking or sourcing
VIL
MAX4031E
±100
VIH
MAX4031E
IIL
SHDN_ = GND (MAX4031E)
0.10
10
IIH
SHDN_ = VCC (MAX4031E)
0.10
10
mA
0.8
2.0
_______________________________________________________________________________________
V
V
µA
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
(VCC = 5V, VCM = 0V, VOUT_ = VCC/2, SHDN_ = VCC, RL = ∞ to VCC/2, TA = TMIN to TMAX, unless otherwise noted. Typical values are
at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
Disabled Output Leakage Current
IOUT_SH
ESD Protection Voltage (Note 2)
TYP
MAX
UNITS
SHDN_ = GND (MAX4031E)
CONDITIONS
MIN
0.1
10
µA
Human Body Model
±15
IEC 1000-4-2 Contact Discharge
±8
IEC 1000-4-2 Air-Gap Discharge
±15
kV
AC ELECTRICAL CHARACTERISTICS
(VCC = 5V, VCM = 1.5V, RL = 150Ω to GND, SHDN_ = VCC, AVCL_ = +2V/V, TA = +25°C, unless otherwise noted.)
PARAMETER
SYMBOL
Small-Signal -3dB Bandwidth
BWSS
Large-Signal -3dB Bandwidth
BWLS
Small-Signal 0.1dB Gain Flatness
BW0.1dBSS
Large-Signal 0.1dB Gain Flatness
BW0.1dBLS
Slew Rate
CONDITIONS
MIN
TYP
VOUT_ = 100mVP-P, AVCL= +1V/V
144
VOUT_ = 100mVP-P, AVCL= +2V/V
53
VOUT_ = 2VP-P, AVCL= +1V/V
52
VOUT_ = 2VP-P, AVCL= +2V/V
40
VOUT_ = 100mVP-P, AVCL= +1V/V
20
VOUT_ = 100mVP-P, AVCL= +2V/V
10
VOUT_ = 2VP-P, AVCL= +1V/V
20
VOUT_ = 2VP-P, AVCL= +2V/V
9
MAX
UNITS
MHz
MHz
MHz
MHz
SR
VOUT_ = 2V step
115
tS
VOUT_ = 2V step
40
ns
f = 4.43MHz
65
dB
DP
NTSC, RL = 150Ω to GND, AVCL = +2V/V
0.2
Degrees
Differential Gain Error
DG
NTSC, RL = 150Ω to GND, AVCL = +2V/V
0.2
%
Input Capacitance
CIN
8
pF
200
pF
Settling Time to 0.1%
Channel-to-Channel Isolation
Differential Phase Error
CHISO
Capacitive-Load Stability
No sustained oscillations
V/µs
f = 4.43MHz
2
Ω
Enable Time
tON
VIN_ = 1V (MAX4031E)
2
µs
Disable Time
tOFF
VIN_ = 1V (MAX4031E)
0.15
µs
Output Impedance
ZOUT
Note 1: All devices are 100% production tested at TA = +25°C. Specifications over temperature limits are guaranteed by design.
Note 2: ESD protection is specified for test point A and test point B only (Figure 7).
_______________________________________________________________________________________
3
MAX4030E/MAX4031E
DC ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics
(VCC = 5V, VCM = 1.5V, AVCL= +2V/V, RL= 150Ω to VCC/2, TA = +25°C, unless otherwise noted.)
3
3
2
2
1
1
GAIN (dB)
0
-1
0.4
0
-1
-2
0
-0.1
-0.2
-4
-4
-5
-0.4
-5
-6
-0.5
10
100
-0.3
0.1
1
0.1
1000
1
OUTPUT IMPEDANCE vs. FREQUENCY
OUTPUT IMPEDANCE (Ω)
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
100
DISTORTION vs. FREQUENCY
0
100
10
1
VOUT = 2VP-P
AVCL = 2V/V
-10
-20
DISTORTION (dBc)
VOUT = 2VP-P
10
FREQUENCY (MHz)
MAX4030 toc05
0.4
100
1000
MAX4030 toc04
0.5
10
FREQUENCY (MHz)
LARGE-SIGNAL GAIN FLATNESS
vs. FREQUENCY
-30
-40
2ND HARMONIC
-50
-60
-70
0.1
-80
0.01
-100
3RD HARMONIC
-90
-0.4
-0.5
0.1
1
10
0.1
1000
100
1
100
10
0.1
FREQUENCY (MHz)
FREQUENCY (MHz)
0.1
0
10
100
POWER-SUPPLY REJECTION
vs. FREQUENCY
0
0
MAX4030 toc08
0.2
1
FREQUENCY (MHz)
COMMON-MODE REJECTION
vs. FREQUENCY
DIFFERENTIAL GAIN
MAX4030 toc07
-20
-20
-0.1
1st
2nd
3rd
4th
5th
6th
DIFFERENTIAL PHASE
0.2
-40
PSR (dB)
-0.2
CMR (dB)
DIFFERENTIAL GAIN (%)
0.1
-3
FREQUENCY (MHz)
-40
-60
-60
-80
-80
0.1
0
-0.1
-0.2
-100
-100
1st
2nd
3rd
4th
5th
6th
0.01
0.1
1
FREQUENCY (MHz)
4
0.2
-3
1
VOUT = 100mVP-P
0.3
-2
0.1
GAIN (dB)
0.5
MAX4030 toc09
GAIN (dB)
VOUT = 2VP-P
MAX4030 toc03
4
MAX4030 toc06
VOUT = 100mVP-P
NORMALIZED GAIN (dB)
4
MAX4030 toc01
5
SMALL-SIGNAL GAIN FLATNESS
vs. FREQUENCY
LARGE-SIGNAL GAIN vs. FREQUENCY
MAX4030 toc02
SMALL-SIGNAL GAIN vs. FREQUENCY
DIFFERENTIAL PHASE (°)
MAX4030E/MAX4031E
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
10
100
0.1
1
10
FREQUENCY (MHz)
_______________________________________________________________________________________
100
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
OUTPUT VOLTAGE SWING
vs. RESISTIVE LOAD
SMALL-SIGNAL PULSE RESPONSE
LARGE-SIGNAL PULSE RESPONSE
MAX4030 toc11
MAX4030 toc12
MAX4030 toc10
0.50
0.45
0.40
VIN
20mV/div
VIN
500mV/div
VOL
0.30
0.25
0.20
0.15
0.10
VOUT
50mV/div
VCC - VOH
VOUT
1V/div
0.05
0
100 150 200 250 300 350 400
20ns/div
20ns/div
RESISTIVE LOAD (Ω)
ISOLATION RESISTANCE
vs. CAPACITIVE LOAD
CROSSTALK vs. FREQUENCY
0
18
16
14
12
10
8
MAX4030 toc14
20
-20
CROSSTALK (dB)
50
MAX4030 toc13
0
RISO (Ω)
VOLTAGE (V)
0.35
-40
-60
6
4
-80
2
0
-100
0
100
200
300
CAPACITIVE LOAD (pF)
400
500
0.1
1
10
100
FREQUENCY (MHz)
_______________________________________________________________________________________
5
MAX4030E/MAX4031E
Typical Operating Characteristics (continued)
(VCC = 5V, VCM = 1.5V, AVCL= +2V/V, RL= 150Ω to VCC/2, TA = +25°C, unless otherwise noted.)
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
MAX4030E/MAX4031E
Pin Description
PIN
NAME
FUNCTION
MAX4030E
MAX4031E
1
7
OUTA
2
6
INA-
3
5
INA+
Amplifier A Noninverting Input
4
11
GND
Ground
5
10
INB+
Amplifier B Noninverting Input
6
9
INB-
Amplifier B Inverting Input
7
8
OUTB
8
4
VCC
—
1
SHDNA
Amplifier A Shutdown Input. Connect SHDNA high to enable amplifier A.
—
2
SHDNC
Amplifier C Shutdown Input. Connect SHDNC high to enable amplifier C.
—
3
SHDNB
Amplifier B Shutdown Input. Connect SHDNB high to enable amplifier B.
—
12
INC+
Amplifier C Noninverting Input
—
13
INC-
Amplifier C Inverting Input
—
14
OUTC
Amplifier A Output
Amplifier A Inverting Input
Amplifier B Output
Positive Power Supply. Bypass VCC to GND with a 0.1µF capacitor.
Amplifier C Output
Detailed Description
Applications Information
The MAX4030E/MAX4031E dual/triple, 5V operational
amplifiers achieve 115V/µs slew rates and 144MHz
bandwidths. High ±15kV ESD protection at video inputs
and outputs guards against unexpected discharge.
Excellent harmonic distortion and differential gain/
phase performance make these amplifiers an ideal
choice for a wide variety of video and RF signal-processing applications.
Choosing Resistor Values
Ground-Sensing Inputs
The MAX4030E/MAX4031E input stage can sense common-mode voltages from ground to within 2.25V of the
positive supply.
Rail-to-Rail Outputs
The MAX4030E/MAX4031E rail-to-rail outputs can
swing to within 100mV of each supply because local
feedback around the output stage ensures low openloop output impedance, reducing gain sensitivity to
load variations.
Shutdown (MAX4031E Only)
The MAX4031E offers individual shutdown control for
each amplifier. Drive SHDN_ low to shut down the
amplifier. In shutdown, the amplifier output impedance
is high impedance.
6
Unity-Gain Configuration
The MAX4030E/MAX4031E are internally compensated
for unity gain. When configured for unity gain, a 24Ω
resistor (RF) in series with the feedback path optimizes
AC performance. This resistor improves AC response by
reducing the Q of the parallel LC circuit formed by the
parasitic feedback capacitance and lead inductance.
Video Line Driver
The MAX4030E/MAX4031E are low-power, voltagefeedback amplifiers featuring bandwidths up to 40MHz
and 0.1dB gain flatness to 9MHz. They are designed to
minimize differential-gain error and differential-phase
error to 0.2% and 0.2°, respectively. They have a 40ns
settling time to 0.1%, 110V/µs slew rates, and outputcurrent-drive capability of up to 50mA, making them
ideal for driving video loads.
Inverting and Noninverting Configurations
Select the feedback (RF) and input (RG) resistor values
to fit the gain requirements of the application. Large
resistor values increase voltage noise and interact with
the amplifier’s input and PC board capacitance. This
can generate undesirable poles and zeros and
_______________________________________________________________________________________
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
•
Use a PC board with at least two layers. The PC
board should be as free from voids as possible.
•
Keep signal lines as short and as straight as possible. Do not make 90° turns; round all corners.
VOUT_
MAX403_E
IN_+
VOUT = [1+ (RF / RG)] VIN_+
RL
150Ω
Figure 1. Noninverting Gain Configuration
RG
RF
IN
VOUT_
MAX403_E
VOUT = -(RF / RG) VIN
RL
150Ω
Figure 2. Inverting Gain Configuration
decrease bandwidth or cause oscillations. For example, a noninverting gain-of-two configuration (RF = RG)
using 2kΩ resistors, combined with 4pF of amplifier
input capacitance and 1pF of PC board capacitance,
cause a pole at 79.6MHz. Since this pole is within the
amplifier bandwidth, it jeopardizes stability. Reducing
the 2kΩ resistors to 100Ω extends the pole frequency
to 1.59GHz, but could limit output swing by adding
200Ω in parallel with the amplifier’s load resistor
(Figures 1 and 2).
Output Capacitive Loading and Stability
The MAX4030E/MAX4031E are optimized for AC performance and do not drive highly reactive loads, which
decreases phase margin and can produce excessive
ringing and oscillation. Figure 3 shows a circuit modification that uses an isolation resistor (RISO) to eliminate
this problem. Figure 4 shows a graph of the Optimal
Isolation Resistor (RISO) vs. Capacitive Load. Figure 5
shows how a capacitive load causes excessive peaking of the amplifier’s frequency response if the capacitor is not isolated from the amplifier by a resistor. A
small isolation resistor (usually 10Ω to 15Ω) placed
before the reactive load prevents ringing and oscillation. At higher capacitive loads, the interaction of the
load capacitance and the isolation resistor controls the
AC performance. Figure 6 shows the effect of a 10Ω
isolation resistor on closed-loop response.
ESD Protection
As with all Maxim devices, ESD protection structures
are incorporated on all pins to protect against ESD
encountered during handling and assembly. Input and
output pins of the MAX4030E/MAX4031E have extra
protection against static electricity. Maxim’s engineers
have developed state-of-the-art structures enabling
these pins to withstand ESD up to ±15kV without damage when placed in the test circuit (Figure 7). The
MAX4030E/MAX4031E are characterized for protection
to the following limits:
• ±15kV using the Human Body Model
•
±8kV using the Contact Discharge method specified in IEC 1000-4-2
•
±15kV using the Air-Gap Discharge method specified in IEC 1000-4-2
Layout and Power-Supply Bypassing
These amplifiers operate from a single 5V power supply. Bypass VCC to ground with a 0.1µF capacitor as
close to VCC as possible. Maxim recommends using
microstrip and stripline techniques to obtain full bandwidth. To ensure that the PC board does not degrade
the amplifier’s performance, design it for a frequency
greater than 1GHz. Pay careful attention to inputs and
outputs to avoid large parasitic capacitance. Under all
conditions observe the following design guidelines:
• Do not use wire-wrap boards. Wire-wrap boards are
too inductive.
•
Do not use IC sockets. Sockets increase parasitic
capacitance and inductance.
•
Use surface mount instead of through-hole components for better high-frequency performance.
RF
24Ω
RISO
MAX403_E
VIN_+
VOUT_
CL
Figure 3. Driving a Capacitive Load Through an Isolation Resistor
_______________________________________________________________________________________
7
MAX4030E/MAX4031E
RF
RG
SMALL-SIGNAL GAIN vs. FREQUENCY WITH LOAD
CAPACITANCE AND 10Ω ISOLATION RESISTOR
ISOLATION RESISTANCE
vs. CAPACITIVE LOAD
6
5
20
18
4
3
2
16
14
GAIN (dB)
RISO (Ω)
12
10
8
6
2
CL = 10pF
1
0
-1
-2
CL = 5pF
-5
-6
0
0
100
200
300
400
500
Figure 4. Isolation Resistance vs. Capacitive Load
SMALL-SIGNAL GAIN vs. FREQUENCY WITH LOAD
CAPACITANCE AND NO ISOLATION RESISTOR
6
5
CL = 20pF
4
3
2
CL = 10pF
1
0
CL = 5pF
-1
-2
-3
-4
-5
-6
0.1
1
10
100
0.1
1
10
100
1000
FREQUENCY (MHz)
CAPACITIVE LOAD (pF)
1000
FREQUENCY (MHz)
Figure 5. Small-Signal Gain vs. Frequency with Load
Capacitance and No Isolation Resistor
Human Body Model
Figure 8 shows the Human Body Model and Figure 9
shows the current waveform it generates when discharged into low impedance. This model consists of a
150pF capacitor charged to the ESD voltage of interest,
and then discharged into the test device through a
1.5kΩ resistor.
8
CL = 20pF
-3
-4
4
GAIN (dB)
MAX4030E/MAX4031E
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
Figure 6. Small-Signal Gain vs. Frequency with Load
Capacitance and 10Ω Isolation Resistor
IEC 1000-4-2
The IEC 1000-4-2 standard covers ESD testing and performance of finished equipment; it does not specifically
refer to ICs. The MAX4030E/MAX4031E enable the
design of equipment that meets the highest level (level
4) of IEC 1000-4-2 without the need for additional ESD
protection components. The major difference between
tests done using the Human Body Model and IEC 10004-2 is higher peak current in IEC 1000-4-2. Because
series resistance is lower in the IEC 1000-4-2 model, the
ESD-withstand voltage measured to this standard is generally lower than that measured using the Human Body.
Figure 10 shows the IEC 1000-4-2 model and Figure 11
shows the current waveform for the ±8kV IEC 1000-4-2
level 4 ESD Contact Discharge test. The Air-Gap test
involves approaching the device with a charged probe.
The Contact Discharge method connects the probe to
the device before the probe is energized.
Chip Information
MAX4030E TRANSISTOR COUNT: 271
MAX4031E TRANSISTOR COUNT: 387
PROCESS: BiCMOS
_______________________________________________________________________________________
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
CBYPASS
0.1µF
TEST
POINT A
CHARGE CURRENT
LIMIT RESISTOR
MAX4030E/MAX4031E
RC
50MΩ TO
100MΩ
5V
RD
330Ω
DISCHARGE
RESISTANCE
75Ω
75Ω
TEST
POINT B
MAX403_E
HIGHVOLTAGE
DC
SOURCE
CS
150pF
STORAGE
CAPACITOR
DEVICE
UNDER
TEST
VEE
200Ω
200Ω
Figure 10. IEC 1000-4-2 ESD Test Model
Figure 7. ESD Test Circuit
I
100%
RD = 1.5kΩ
HIGHVOLTAGE
DC
SOURCE
CHARGE CURRENT
LIMIT RESISTOR
CS = 150pF
90%
I PEAK
RC = 1MΩ
DISCHARGE
RESISTANCE
DEVICE
UNDER
TEST
STORAGE
CAPACITOR
10%
t r = 0.7ns TO 1ns
Figure 8. Human Body ESD Model
t
30ns
60ns
Figure 11. IEC 1000-4-2 ESD Generator Current Waveform
IP 100%
90%
Ir
PEAK-TO-PEAK RINGING
(NOT DRAWN TO SCALE)
AMPERES
36.8%
10%
0
0
tRL
TIME
tDL
CURRENT WAVEFORM
Figure 9. Human Body Current Waveform
_______________________________________________________________________________________
9
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
4X S
8
8
INCHES
DIM
A
A1
A2
b
E
Ø0.50±0.1
H
c
D
e
E
H
0.6±0.1
L
1
1
α
0.6±0.1
S
BOTTOM VIEW
D
MIN
0.002
0.030
MAX
0.043
0.006
0.037
0.014
0.010
0.007
0.005
0.120
0.116
0.0256 BSC
0.120
0.116
0.198
0.188
0.026
0.016
6∞
0∞
0.0207 BSC
8LUMAXD.EPS
MAX4030E/MAX4031E
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
MILLIMETERS
MAX
MIN
0.05
0.75
1.10
0.15
0.95
0.25
0.36
0.13
0.18
2.95
3.05
0.65 BSC
2.95
3.05
4.78
5.03
0.41
0.66
0∞
6∞
0.5250 BSC
TOP VIEW
A1
A2
A
α
c
e
FRONT VIEW
b
L
SIDE VIEW
PROPRIETARY INFORMATION
TITLE:
PACKAGE OUTLINE, 8L uMAX/uSOP
APPROVAL
DOCUMENT CONTROL NO.
21-0036
10
______________________________________________________________________________________
REV.
J
1
1
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
TSSOP4.40mm.EPS
PACKAGE OUTLINE, TSSOP 4.40mm BODY
21-0066
G
1
1
______________________________________________________________________________________
11
MAX4030E/MAX4031E
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
DIM
A
A1
B
C
e
E
H
L
N
E
H
INCHES
MILLIMETERS
MAX
MIN
0.069
0.053
0.010
0.004
0.014
0.019
0.007
0.010
0.050 BSC
0.150
0.157
0.228
0.244
0.016
0.050
MAX
MIN
1.35
1.75
0.10
0.25
0.35
0.49
0.19
0.25
1.27 BSC
3.80
4.00
5.80
6.20
0.40
SOICN .EPS
MAX4030E/MAX4031E
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
1.27
VARIATIONS:
1
INCHES
TOP VIEW
DIM
D
D
D
MIN
0.189
0.337
0.386
MAX
0.197
0.344
0.394
MILLIMETERS
MIN
4.80
8.55
9.80
MAX
5.00
8.75
10.00
N MS012
8
AA
14
AB
16
AC
D
C
A
B
e
0∞-8∞
A1
L
FRONT VIEW
SIDE VIEW
PROPRIETARY INFORMATION
TITLE:
PACKAGE OUTLINE, .150" SOIC
APPROVAL
DOCUMENT CONTROL NO.
21-0041
REV.
B
1
1
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2005 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products, Inc.
工商网监
湘ICP备2023018690号
