Click here for production status of specific part numbers.
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
General Description
The MAX4400–MAX4403 low-cost, general-purpose op
amps offer rail-to-rail outputs, draw only 320µA of quiescent current, and operate from a single +2.5V to +5.5V
supply. For additional power conservation, the MAX4401
offers a low-power shutdown mode that reduces supply
current to 1µA (max) and puts the amplifier’s output in
a high-impedance state. These devices deliver ±1.4mA
of output current and are unity-gain stable with a 1MHz
gain-bandwidth product driving capacitive loads up to
400pF. The MAX4400–MAX4403 are specified to +125°C,
making them suitable for use in a variety of harsh environments, such as automotive applications.
The MAX4400 single amplifier is available in ultra-small
5-pin SC70 and space-saving 5-pin SOT23 packages.
The single MAX4401 includes the shutdown feature and
is available in a 6-pin SC70. The MAX4402 is a dual
amplifier available in 8-pin SOT23, µMAX®, and SO
packages. The MAX4403 quad amplifier is packaged in a
14-pin TSSOP or SO.
Applications
●●
●●
●●
●●
●●
●●
●●
Benefits and Features
●● Single +2.5V to +5.5V Supply Voltage Range
●● 320µA Quiescent Current per Amplifier
●● 1µA (max) Shutdown Mode (MAX4401)
●● Available in Space-Saving Packages
5-Pin SC70 (MAX4400)
6-Pin SC70 (MAX4401)
8-Pin SOT23/µMAX (MAX4402)
●● 110dB AVOL with 2kΩ Load
●● 0.015% THD with 2kΩ Load
●● Rail-to-Rail Output Voltage Swing
●● 1.4mA of Sink and Source Load Current
●● Unity-Gain Stable up to CLOAD = 400pF
●● Ground-Sensing Inputs
●● AEC-Q100 Qualified (MAX4402AKA/V+ and
MAX4402AUA/V+ Only)
Pin Configurations
MAX4400
Single-Supply, Zero-Crossing Detectors
Instruments and Terminals
Portable Communications
Electronic Ignition Modules
Infrared Receivers
Sensor Signal Detection
Automotive
IN+ 1
+
MAX4401
5 VDD
VSS 2
4 OUT
IN- 3
SC70-5/SOT23-5
IN+ 1
+
6 VDD
VSS 2
5 SHDN
IN- 3
4 OUT
SC70-6
Pin Configurations continued at end of data sheet.
Selector Guide
PART
NO. OF AMPLIFIERS
PER PACKAGE
SHUTDOWN
MODE
MAX4400
1
No
MAX4401
1
Yes
MAX4402
2
No
MAX4403
4
No
µMAX is a registered trademark of Maxim Integrated Products, Inc.
19-1599; Rev 8; 1/19
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
Absolute Maximum Ratings
Power-Supply Voltage (VDD to VSS)........................-0.3V to +6V
All Other Pins................................. (VSS - 0.3V) to (VDD + 0.3V)
Output Short-Circuit Duration
OUT Shorted to VSS or VDD................................. Continuous
Continuous Power Dissipation (TA = +70°C)
5-Pin SC70 (derate 3.10mW/°C above +70°C)...... 246.90mW
5-Pin SOT23 (derate 3.90mW/°C above +70°C)....312.60mW
6-Pin SC70 (derate 3.10mW/°C above +70°C)............245mW
8-Pin SOT23 (derate 5.10mW/°C above +70°C)......408.2mW
8-Pin µMAX (derate 4.5mW/°C above +70°C)............ 362mW
8-Pin SO (derate 5.88mW/°C above +70°C)............... 471mW
14-Pin TSSOP (derate 8.33mW/°C above +70°C). 727.30mW
14-Pin SO (derate 9.10mW/°C above +70°C)............. 667mW
Operating Temperature Range.......................... -40°C to +125°C
Storage Temperature Range............................. -65°C to +150°C
Lead Temperature (soldering, 10s).................................. +300°C
Soldering Temperature (reflow)........................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Package Information
5 SC70
PACKAGE CODE
X5+1
Outline Number
21-0076
Land Pattern Number
90-0188
Thermal Resistance, Single-Layer Board:
Junction to Ambient (θJA)
324°C/W
Junction to Case (θJC)
115°C/W
Thermal Resistance, Four-Layer Board:
Junction to Ambient (θJA)
324°C/W
Junction to Case (θJC)
115°C/W
5 SOT23
PACKAGE CODE
U5+1
Outline Number
21-0057
Land Pattern Number
90-0174
Thermal Resistance, Single-Layer Board:
Junction to Ambient (θJA)
324.30°C/W
Junction to Case (θJC)
82°C/W
Thermal Resistance, Four-Layer Board:
Junction to Ambient (θJA)
255.90°C/W
Junction to Case (θJC)
81°C/W
6 SC70
PACKAGE CODE
X6SN+1
Outline Number
21-0077
Land Pattern Number
90-0189
Thermal Resistance, Single-Layer Board:
Junction to Ambient (θJA)
326°C/W
Junction to Case (θJC)
115°C/W
Thermal Resistance, Four-Layer Board:
Junction to Ambient (θJA)
326.50°C/W
Junction to Case (θJC)
115°C/W
www.maximintegrated.com
Maxim Integrated │ 2
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
Package Information (continued)
8 SOT23
PACKAGE CODE
K8+5, K8+5A
Outline Number
21-0078
Land Pattern Number
90-0176
Thermal Resistance, Single-Layer Board:
Junction to Ambient (θJA)
N/A
Junction to Case (θJC)
800°C/W
Thermal Resistance, Four-Layer Board:
Junction to Ambient (θJA)
196°C/W
Junction to Case (θJC)
70°C/W
8 µMAX
PACKAGE CODE
U8+1
Outline Number
21-0036
Land Pattern Number
90-0092
Thermal Resistance, Single-Layer Board:
Junction to Ambient (θJA)
221°C/W
Junction to Case (θJC)
42°C/W
Thermal Resistance, Four-Layer Board:
Junction to Ambient (θJA)
206.30°C/W
Junction to Case (θJC)
42°C/W
8 SO
PACKAGE CODE
S8+2
Outline Number
21-0041
Land Pattern Number
90-0096
Thermal Resistance, Single-Layer Board:
Junction to Ambient (θJA)
170°C/W
Junction to Case (θJC)
40°C/W
Thermal Resistance, Four-Layer Board:
Junction to Ambient (θJA)
136°C/W
Junction to Case (θJC)
38°C/W
14 TSSOP
PACKAGE CODE
U14+1
Outline Number
21-0066
Land Pattern Number
90-0113
Thermal Resistance, Single-Layer Board:
Junction to Ambient (θJA)
110°C/W
Junction to Case (θJC)
30°C/W
Thermal Resistance, Four-Layer Board:
Junction to Ambient (θJA)
100.40°C/W
Junction to Case (θJC)
30°C/W
www.maximintegrated.com
Maxim Integrated │ 3
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
Package Information (continued)
14 SO
PACKAGE CODE
S14+1
Outline Number
21-0041
Land Pattern Number
90-0112
Thermal Resistance, Single-Layer Board:
Junction to Ambient (θJA)
120°C/W
Junction to Case (θJC)
37°C/W
Thermal Resistance, Four-Layer Board:
Junction to Ambient (θJA)
84°C/W
Junction to Case (θJC)
34°C/W
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”,
“#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing
pertains to the package regardless of RoHS status.
Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer board.
For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial.
www.maximintegrated.com
Maxim Integrated │ 4
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
Electrical Characteristics
(VDD = +5V, VSS = 0V, VCM = 0V, VOUT = VDD/2, RL = ∞ connected to VDD/2, SHDN = VDD (MAX4401 only), TA = +25°C, unless
otherwise noted.)
PARAMETER
Supply Voltage Range
Supply Current per Amplifier
Supply Current in Shutdown
SYMBOL
VDD
IDD
ISHDN
CONDITIONS
Inferred from PSRR test
MIN
TYP
2.5
VDD = 2.5V
MAX
UNITS
55
V
320
VDD = 5.0V
410
SHDN = VSS (Note 1)
700
0.00002
1
MAX4400/MAX4401
±0.8
±4.5
MAX4402/MAX4403
±1.0
±5.5
µA
µA
Input Offset Voltage
VOS
Input Bias Current
(Note 2)
±0.1
±100
pA
(Note 2)
±0.1
±100
pA
Input Resistance
IB
IOS
RIN
Differential or common mode
1000
Input Common-Mode Voltage
Range
VCM
Inferred from CMRR test
VSS
Common-Mode Rejection Ratio
CMRR
68
84
dB
Power-Supply Rejection Ratio
PSRR
VSS ≤ VCM ≤ VDD - 1.4V
2.5V ≤ VDD ≤ 5.5V
78
100
dB
RL = 100kΩ
90
Input Offset Current
Large-Signal Voltage Gain
AVOL
VSS + 0.3V ≤
VOUT ≤ VDD - 0.3V
Output Voltage High
VOH
Specified as
|VDD - VOH|
RL = 100kΩ
Output Voltage Low
VOL
Specified as
|VSS - VOL|
RL = 100kΩ
Sourcing
Output Short-Circuit Current
SHDN Logic-High
SHDN Input Current
Gain-Bandwidth Product
Phase Margin
Gain Margin
VIL
VIH
IIL, IIH
GBW
SR
Input Voltage-Noise Density
en
Input Current-Noise Density
Capacitive-Load Stability
Shutdown Delay Time
Enable Delay Time
Power-On Time
in
CLOAD
tSHDN
tEN
CIN
Total Harmonic Distortion
THD
www.maximintegrated.com
30
f = 10kHz
f = 10kHz
AV = +1V/V
AV = +1V/V
(Note 1)
tS
f = 10kHz, V OUT = RL = 100kΩ
2VP-P, AV = +1V/V RL = 2kΩ
VOUT = 2V step
75
12
0.7 × V DD
±0.001
800
mV
mV
mA
30
(Note 1)
SHDN = VDD or VSS (Note 1)
200
2
Device in shutdown mode, SHDN = SS,
VSS < VOUT < VCC (Note 1)
tON
Input Capacitance
Settling Time to 0.1%
3
RL = 2kΩ
V
dB
110
55
fM
Slew Rate
VDD - 1.4
RL = 2kΩ
(Note 1)
GΩ
120
Sinking
Shutdown Mode Output Leakage IOUTSHDN
SHDN Logic-Low
RL = 2kΩ
mV
±1.0
µA
0.3 × VDD
V
±500
nA
V
kHz
70
°
20
dB
1
V/µs
36
nV/√Hz
1
fA/√Hz
400
pF
0.4
μs
6
μs
5
μs
2.5
pF
0.009
0.015
7
%
μs
Maxim Integrated │ 5
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
Electrical Characteristics
(VDD = +5V, VSS = 0V, VCM = 0V, VOUT = VDD/2, RL = ∞ connected to VDD/2, TA = -40°C to +125°C, unless otherwise noted.) (Note 3)
PARAMETER
SYMBOL
Supply Voltage Range
VDD
Supply Current per Amplifier
IDD
Input Offset Voltage
Input Offset Voltage Drift
Input Bias Current
Input Offset Current
Input Common-Mode Voltage
Range
VOS
Inferred by PSRR test
MIN
TYP
2.5
MAX4400/MAX4401
MAX4402/MAX4403
MAX
UNITS
5.5
V
800
±6.5
µA
±8.0
TCVOS
±1
mV
μV/°C
IB
(Note 2)
±100
pA
IOS
(Note 2)
±100
pA
VCM
Inferred from CMRR test
VSS
VSS ≤ VCM ≤ VDD - 1.5V
65
VSS ≤ VCM ≤ VDD - 1.0V TA = -20°C to +125°C
50
2.5V ≤ VCC ≤ 5.5V
74
Common-Mode Rejection Ratio
CMRR
Power-Supply Rejection Ratio
PSRR
Shutdown Mode Output
Leakage
CONDITIONS
Device in shutdown
mode, SHDN = VSS,
IOUTSHDN
VSS < VOUT < VDD
(Note 1)
SHDN Logic-Low
VIL
(Note 1)
SHDN Logic-High
VIH
(Note 1)
VDD - 1.5
V
dB
dB
TA = -40°C to +85°C
±1.0
TA = +85°C to +125°C
±5.0
μA
0.3 × VDD
0.7 × VDD
V
V
SHDN Input Current
IIL, IIH
SHDN = VDD or VSS (Notes 1, 2)
Large-Signal Voltage Gain
AVOL
VSS + 0.3V ≤ VOUT ≤ VDD - 0.3V, RL = 2kΩ
±1000
Output Voltage High
VOH
Specified as |VDD - VOH|, RL = 2kΩ
250
mV
Output Voltage Low
VOL
Specified as |VSS - VOL|, RL = 2kΩ
100
mV
85
nA
dB
Note 1: Shutdown mode is only available in the 6-pin SC70 single op amp (MAX4401).
Note 2: Guaranteed by design.
Note 3: Specifications are 100% tested at TA = +25°C (exceptions noted). All temperature limits are guaranteed by design.
www.maximintegrated.com
Maxim Integrated │ 6
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
Typical Operating Characteristics
(VDD = +5V, VSS = 0V, VCM = VDD/2, VSHDN = 5V, RL = ∞ connected to VDD/2, TA = +25°C, unless otherwise noted.)
AVCL = +1000V/V
100
10k 100k
1M
10M
PSRR (dB)
-90
AVCL = +1000V/V
1
10
100
10k 100k
1k
1M
10M
-110
10k
100k
450
100k
400
350
10k
100k
300
1M
-40
-20
0
20
40
60
80
-40 -20
0
TEMPERATURE (°C)
-1500
70
80
100 120
RL = 2kΩ to VDD/2
60
VDD - VOH (mV)
0
40
30
20
-1000
100 120
60
50
-500
80
40
OUTPUT VOLTAGE SWING HIGH
vs. TEMPERATURE
MAX4400 toc08
1000
VOS (µV)
ILEAK (pA)
10
20
TEMPERATURE (°C)
500
www.maximintegrated.com
1
100 120
1500
1k
60
100
INPUT OFFSET VOLTAGE
vs. TEMPERATURE
MAX4400 toc07
VSHDN = VSS
VOUT = VDD/2
40
1k
TEMPERATURE (°C)
MAX4401
OUTPUT LEAKAGE CURRENT
vs. TEMPERATURE
20
10k
10
FREQUENCY (Hz)
0
VSHDN = VSS
MAX4400 toc09
1k
1M
MAX4400 toc06
500
SUPPLY CURRENT (µA)
100
-40 -20
1k
MAX4401
SHUTDOWN SUPPLY CURRENT
vs. TEMPERATURE
0.01
0.1
100
SUPPLY CURRENT
vs. TEMPERATURE
0.1
1M
10
OUTPUT IMPEDANCE
vs. FREQUENCY
1
10
MAX4400 toc03
-70
FREQUENCY (Hz)
10
0.001
-50
FREQUENCY (Hz)
100
OUTPUT IMPEDANCE (Ω)
-10
FREQUENCY (Hz)
MAX4400 toc4
1000
1k
10
SUPPLY CURRENT (pA)
10
POWER-SUPPLY REJECTION RATIO
vs. FREQUENCY
-30
MAX4400 toc05
1
80
60
40
20
0
-20
-40
-60
-80
-100
-120
-140
-160
-180
GAIN AND PHASE
vs. FREQUENCY (CL = 400pF)
MAX4400 toc02
MAX4400 toc01
80
60
40
20
0
-20
-40
-60
-80
-100
-120
-140
-160
-180
GAIN (dB)/PHASE (degrees)
GAIN (dB)/PHASE (degrees)
GAIN AND PHASE
vs. FREQUENCY (NO LOAD)
10
0
-40 -20
0
20
40
60
80
TEMPERATURE (°C)
100 120
-40 -20
0
20
40
60
80
100 120
TEMPERATURE (°C)
Maxim Integrated │ 7
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
Typical Operating Characteristics (continued)
(VDD = +5V, VSS = 0V, VCM = VDD/2, VSHDN = 5V, RL = ∞ connected to VDD/2, TA = +25°C, unless otherwise noted.)
-80
MAX4400 toc12
80
60
40
-90
10
20
0
20
40
60
80
-40 -20
0
20
40
60
80
0
100 120
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5
TEMPERATURE (°C)
VOUT (V)
LARGE-SIGNAL GAIN
vs. TEMPERATURE
MINIMUM OPERATING VOLTAGE
vs. TEMPERATURE
TOTAL HARMONIC DISTORTION
vs. FREQUENCY
0.1
MAX4400 toc14
3.0
RL = 2kΩ
VOUT = 2VP-P
AV = +1
2.5
130
MAX4400 toc15
TEMPERATURE (°C)
RL = 2kΩ
135
-100
100 120
MAX4400 toc13
-40 -20
140
120
THD (%)
0.01
125
VMIN (V)
GAIN (dB)
100
GAIN (dB)
CMRR (dB)
20
RL = 2kΩ
120
-70
30
0
140
MAX4400 toc11
RL = 2kΩ to VDD/2
40
VOL - VEE (mV)
-60
MAX4400 toc10
50
LARGE-SIGNAL GAIN
vs. OUTPUT VOLTAGE
COMMON-MODE REJECTION RATIO
vs. TEMPERATURE
OUTPUT VOLTAGE SWING LOW
vs. TEMPERATURE
2.0
115
0.001
1.5
110
105
-40 -20
20
40
60
80
1.0
100 120
-40 -20
0
20
40
60
80
0.0001
100 120
1k
10k
100k
TOTAL HARMONIC DISTORTION
vs. FREQUENCY
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. INPUT AMPLITUDE
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. INPUT AMPLITUDE
RL = 2kΩ
f = 10kHz
BW = 20kHz
0.1
0.01
0.001
100
1k
FREQUENCY (Hz)
www.maximintegrated.com
10k
100k
0.0001
RL = 100kΩ
f = 10kHz
BW = 20kHz
1
THD + N (%)
1
10
MAX4400 toc17
10
MAX4400 toc18
FREQUENCY (Hz)
RL = 100kΩ
VOUT = 2VP-P
AV = +1
10
100
TEMPERATURE (°C)
0.001
0.0001
10
TEMPERATURE (°C)
THD + N (%)
THD (%)
0.01
0
MAX4400 toc16
100
0.1
0.01
0.001
0
0.5
1.0
1.5
VIN (VP-P)
2.0
2.5
3.0
0.0001
0
0.5
1.0
1.5
2.0
2.5
3.0
VIN (VP-P)
Maxim Integrated │ 8
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
Typical Operating Characteristics (continued)
(VDD = +5V, VSS = 0V, VCM = VDD/2, VSHDN = 5V, RL = ∞ connected to VDD/2, TA = +25°C, unless otherwise noted.)
AV = +1V/V
RL = 2kΩ
MAX4400 toc19
2000
AV = +1
TA = +25°C
MAX4400 toc20
NONINVERTING SMALL-SIGNAL
TRANSIENT RESPONSE
CAPACITIVE-LOAD STABILITY
CAPACITIVE LOAD (pF)
1500
IN
UNSTABLE
REGION
50mV/div
1000
STABLE
REGION
500
0
OUT
1k
10k
2µs/div
100k
RESISTIVE LOAD (Ω)
30
MAX4400 toc21
NEGATIVE OVERSHOOT
25
IN
2V/div
OVERSHOOT (%)
AV = +1V/V
RL = 2kΩ
MAX4400 toc22
PERCENT OVERSHOOT
vs. CAPACITIVE LOAD
NONINVERTING LARGE-SIGNAL
TRANSIENT RESPONSE
20
15
10
OUT
5
0
10µs/div
POSITIVE OVERSHOOT
0
100
200
300
400
500
600
CLOAD (pF)
MAX4402/MAX4403
CHANNEL-TO-CHANNEL ISOLATION
vs. FREQUENCY
300
250
200
150
100
50
0
0
1
2
3
4
SUPPLY VOLTAGE (V)
www.maximintegrated.com
5
6
MAX4400 toc25
350
130
CHANNEL-TO-CHANNEL ISOLATION (dB)
VOUT = VDD/2
400
SUPPLY CURRENT (µA)
MAX4400 toc24
SUPPLY CURRENT vs. SUPPLY VOLTAGE
450
120
110
100
90
80
70
60
50
0.01
0.1
1
10
100
1000
FREQUENCY (kHz)
Maxim Integrated │ 9
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
Pin Description
PIN
NAME
FUNCTION
MAX4400
MAX4401
MAX4402
MAX4403
1
1
—
—
IN+
—
—
3
3
INA+
Noninverting Amplifier Input A
—
—
5
5
INB+
Noninverting Amplifier Input B
—
—
—
10
INC+
Noninverting Amplifier Input C
—
—
—
12
IND+
Noninverting Amplifier Input D
2
2
4
11
VSS
Negative Supply. Connect to ground for single- supply
operation.
Inverting Amplifier Input
Noninverting Amplifier Input
3
3
—
—
IN-
—
—
2
2
INA-
Inverting Amplifier Input A
—
—
6
6
INB-
Inverting Amplifier Input B
—
—
—
9
INC-
Inverting Amplifier Input C
—
—
—
13
IND-
Inverting Amplifier Input D
4
4
—
—
OUT
Amplifier Output
—
—
1
1
OUTA
Amplifier Output A
—
—
7
7
OUTB
Amplifier Output B
—
—
—
8
OUTC
Amplifier Output C
—
—
—
14
OUTD
Amplifier Output D
5
6
8
4
VDD
—
5
—
—
SHDN
Positive Supply
Active-Low Shutdown Input. Connect to VDD for normal
operation. Do not leave unconnected.
Detailed Description
Rail-to-Rail Output Stage
The MAX4400–MAX4403 can drive a 2kΩ load and still
typically swing within 55mV of the supply rails. Figure 1
shows the output voltage swing of the MAX4400 configured with AV = +10V/V.
1V/div
Driving Capacitive Loads
Driving a capacitive load can cause instability in many op
amps, especially those with low quiescent current. The
MAX4400–MAX4403 are unity-gain stable for a range
of capacitive loads to above 400pF. Figure 2 shows the
response of the MAX4400 with an excessive capacitive
load. Adding a series resistor between the output and the
load capacitor (Figure 3) improves the circuit’s response
by isolating the load capacitance from the op amp’s output.
www.maximintegrated.com
100µs/div
Figure 1. Rail-to-Rail Output Operation
Maxim Integrated │ 10
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
IN
RISO
50mV/div
CL
MAX4400
MAX4401
MAX4402
MAX4403
OUT
2µs/div
Figure 2. Small-Signal Transient Response with Excessive
Capacitive Load
SHDN
Figure 3. Capacitive-Load-Driving Circuit
VDD
2V/div
2V/div
OUT
OUT
1V/div
RL = 10MΩ TO GND
CL = 25pF
400µs/div
10µs/div
Figure 4. Shutdown Waveform
Figure 5. Power-Up/Power-Down Waveform
Applications Information
Power Supplies and Layout
Shutdown Mode
The MAX4401 features a low-power shutdown mode.
When SHDN goes low, the supply current drops to 20pA
(typ) and the output enters a high-impedance state. Pull
SHDN high to enable the amplifier. Do not leave SHDN
unconnected. Figure 4 shows the shutdown waveform.
Power-Up
The MAX4400–MAX4403 outputs typically settle within
5µs after power-up. Figure 5 shows the output voltage on
power-up and power-down.
www.maximintegrated.com
The MAX4400–MAX4403 operate from a single +2.5V
to +5.5V power supply. Bypass the power supply with a
0.1µF capacitor to ground.
Good layout techniques optimize performance by
decreasing the amount of stray capacitance at the op
amp’s inputs and outputs. To decrease stray capacitance,
minimize trace lengths by placing external components
close to the op amp’s pins.
Maxim Integrated │ 11
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
Pin Configurations (continued)
MAX4403
OUTA 1
MAX4402
OUTA 1
+
+
14 OUTD
INA- 2
13 IND-
INA+ 3
12 IND+
VDD 4
11 VSS
INB+ 5
10 INC+
INB- 6
9 INC-
8 VDD
INA- 2
7 OUTB
INA+ 3
6 INB-
VSS 4
5 INB+
SOT23-8/SO/µMAX
8 OUTC
OUTB 7
TSSOP/SO
Ordering Information
PINPACKAGE
TOP
MARK
PART
TEMP RANGE
MAX4400AXK+T
-40°C to +125°C
5 SC70
MAX4400AUK+T
-40°C to +125°C
5 SOT23
MAX4401AXT+T
-40°C to +125°C
6 SC70
AAB
MAX4402AKA+T
-40°C to +125°C
8 SOT23
AADI
MAX4402AKA/V+T -40°C to +125°C
8 SOT23
AETR
MAX4402AUA+
-40°C to +125°C
8 µMAX
—
MAX4402AUA/V+T -40°C to +125°C
8 µMAX
—
MAX4402ASA+
-40°C to +125°C
8 SO
—
MAX4403AUD+
-40°C to +125°C
14 TSSOP
—
MAX4403ASD+
-40°C to +125°C
14 SO
—
AAG
ADNP
+Denotes a lead(Pb)-free/RoHS-compliant package.
/V denotes an automotive qualified part.
T = Tape and reel.
www.maximintegrated.com
Maxim Integrated │ 12
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
Revision History
REVISION
NUMBER
REVISION
DATE
PAGES
CHANGED
DESCRIPTION
0
1/00
Initial Release
1
11/00
Release of MAX4402.
1, 2, 9
—
2
7/00
Release of MAX4403.
1, 6, 7
3
9/01
Added µMAX package to data sheet.
1, 2, 9
4
7/12
Added automotive package for MAX4402 to data sheet.
1
5
6/14
Added MAX4402AKA/V+T automotive package to data sheet.
1
6
10/17
Added AEC qualfication statement to Benefits and Features section
1
7
3/18
Added Package Information section and updated Absolute Maximum Ratings
section
2
8
1/19
Updated Applications and Package Information sections
1, 2–4, 12
For pricing, delivery, and ordering information, please visit Maxim Integrated’s online storefront at https://www.maximintegrated.com/en/storefront/storefront.html.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits)
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
© 2019 Maxim Integrated Products, Inc. │ 13