EVALUATION KIT AVAILABLE
MAX5090A/B/C
2A, 76V, High-Efficiency MAXPower
Step-Down DC-DC Converters
General Description
The MAX5090A/B/C easy-to-use, high-efficiency, highvoltage step-down DC-DC converters operate from an input
voltage up to 76V, and consume only 310µA quiescent
current at no load. This pulse-width-modulated (PWM)
converter operates at a fixed 127kHz switching frequency at
heavy loads, and automatically switches to pulse-skipping
mode to provide low quiescent current and high efficiency
at light loads. The MAX5090 includes internal frequency
compensation simplifying circuit implementation. The
device can also be synchronized with external system clock
frequency in a noise-sensitive application. The MAX5090
uses an internal low on-resistance and a high-voltage DMOS
transistor to obtain high efficiency and reduce overall system
cost. This device includes undervoltage lockout, cycleby-cycle current limit, hiccup-mode output short-circuit
protection, and overtemperature shutdown.
The MAX5090 delivers up to 2A output current. External
shutdown is included, featuring 19µA (typ) shutdown
current. The MAX5090A/MAX5090B versions have fixed
output voltages of 3.3V and 5V, respectively, while the
MAX5090C features an adjustable 1.265V to 11V output
voltage.
The MAX5090 is available in a space-saving 16-pin
thin QFN package (5mm x 5mm) and operates over the
automotive temperature range (-40°C to +125°C).
Applications
●● Industrial
●● Distributed Power
Features
●● Wide Input Voltage Range: 6.5V to 76V
●● Fixed (3.3V, 5V) and Adjustable (1.265V to 11V)
Output-Voltage Versions
●● 2A Output Current
●● Efficiency Up to 92%
●● Internal 0.26Ω High-Side DMOS FET
●● 310µA Quiescent Current at No Load
●● 19µA Shutdown Current
●● Internal Frequency Compensation
●● Fixed 127kHz Switching Frequency
●● External Frequency Synchronization
●● Thermal Shutdown and Short-Circuit Current Limit
●● -40°C to +125°C Automotive Temperature Range
●● 6-Pin (5mm x 5mm) Thin QFN Package
●● Capable of Dissipating 2.67W at +70°C
Ordering Information
TEMP
RANGE
PART
PINPACKAGE
OUTPUT
VOLTAGE
(V)
MAX5090AATE+ -40°C to +125°C 16 TQFN-EP*
3.3
MAX5090AATE -40°C to +125°C 16 TQFN-EP*
MAX5090BATE+ -40°C to +125°C 16 TQFN-EP*
MAX5090BATE -40°C to +125°C 16 TQFN-EP*
+Denotes a lead(Pb)-free/RoHS-compliant package.
*EP = Exposed pad.
3.3
5.0
5.0
Ordering Information continued at end of data sheet.
Typical Operating Circuit
DRAIN
100µH
LX
CBST
0.22µF
ON/OFF
MAX5090B
D1
PDS5100H
BST
FB
SS
SYNC
SGND
PGND
VD
CSS
0.047µF
3.3µF
VOUT
5V/2A
COUT
100µF
DRAIN 13
SGND
ON/OFF
11
10
9
EP
FB
7
SS
6
SYNC
N.C. 16
5
VD
MA5090
1
2
3
4
TQFN
19-3872; Rev 1; 9/14
8
N.C. 15
DRAIN 14
VIN
VIN
12
LX
CBYPASS
0.47µF
BST
CIN
68µF
N.C.
TOP VIEW
RIN
10Ω
LX
VIN
7.5V TO 76V
PGND
Pin Configuration
MAX5090A/B/C
2A, 76V, High-Efficiency MAXPower
Step-Down DC-DC Converters
Absolute Maximum Ratings
(Voltages referenced to PGND, unless otherwise specified.)
VIN, DRAIN.............................................................-0.3V to +80V
SGND, PGND........................................................-0.3V to +0.3V
LX................................................................-0.8V to (VIN + 0.3V)
BST...............................................................-0.3V to (VIN + 10V)
BST to LX...............................................................-0.3V to +10V
ON/OFF.......................................................-0.3V to (VIN + 0.3V)
VD, SYNC..............................................................-0.3V to +12V
SS............................................................................... -0.3 to +4V
FB
MAX5090A/MAX5090B......................................-0.3V to +15V
MAX5090C................. 1mA (internally clamped to +2V, -0.3V)
VOUT Short-Circuit Duration.......................................Continuous
VD Short-Circuit Duration...........................................Continuous
Continuous Power Dissipation (TA = +70°C)*
16-Pin TQFN (derate 33.3mW/°C above +70°C).........2.667W
Operating Junction Temperature Range....... -40°C to +125°C
Storage Temperature Range......................... -65°C to +150°C
Junction Temperature...................................................+150°C
Lead Temperature (soldering, 10s).............................. +300°C
*As per JEDEC 51 Standard Multilayer Board.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics
(VIN = +12V, VON/OFF = +12V, VSYNC = 0V, IOUT = 0, TA = TJ = -40°C to +125°C, unless otherwise noted. Typical values are at
TA = +25°C. See the Typical Operating Circuit.) (Note 1)
PARAMETER
Input Voltage Range
Undervoltage Lockout
UVLO Hysteresis
Output Voltage
Output Voltage Range
Feedback Voltage
Efficiency
SYMBOL
UVLO
MIN
VOUT
VOUT
VFB
η
IQ
Quiescent Supply Current
(Note 2)
IQ
Quiescent Supply Current
(Note 2)
IQ
ISHDN
TYP
6.5
6.17
MAX
UNITS
76.0
V
6.45
V
VIN rising
5.70
MAX5090A VIN = 6.5V to 76V, IOUT = 0 to 2A
3.20
3.3
3.39
UVLOHYS
Quiescent Supply Current
(Note 2)
Shutdown Current
CONDITIONS
VIN
0.5
V
MAX5090B VIN = 7.5V to 76V, IOUT = 0 to 2A
4.85
5.0
5.15
MAX5090B VIN = 7V to 76V, IOUT = 0 to 1A
4.85
5.0
5.15
MAX5090C only
1.265
MAX5090C, VIN = 6.5V to 76V
1.191
1.228
MAX5090A VIN = 12V, IOUT = 1A
80
V
11.000
V
1.265
V
MAX5090B VIN = 12V, IOUT = 1A
88
MAX5090C VIN = 12V, VOUT = 5V, IOUT = 1A
88
%
MAX5090A VIN = 6.5V to 28V
310
550
MAX5090B VIN = 7V to 28V
310
550
MAX5090C VIN = 6.5V to 28V
310
550
MAX5090A VIN = 6.5V to 40V
310
570
MAX5090B VIN = 7V to 40V
310
570
MAX5090C VIN = 6.5V to 40V
310
570
MAX5090A VIN = 6.5V to 76V
310
650
MAX5090B VIN = 7V to 76V
310
650
MAX5090C VIN = 6.5V to 76V
310
650
VON/OFF = 0V, VIN = 14V
19
45
CSS = 0
700
µA
µA
µA
µA
SOFT-START
Default Internal Soft-Start
Period
Soft-Start Charge Current
Soft-Start ReferenceVoltage
www.maximintegrated.com
µs
ISS
4.5
10
16.0
µA
VSS(REF)
1.23
1.46
1.65
V
Maxim Integrated │ 2
MAX5090A/B/C
2A, 76V, High-Efficiency MAXPower
Step-Down DC-DC Converters
Electrical Characteristics (continued)
(VIN = +12V, VON/OFF = +12V, VSYNC = 0V, IOUT = 0, TA = TJ = -40°C to +125°C, unless otherwise noted. Typical values are at
TA = +25°C. See the Typical Operating Circuit.) (Note 1)
PARAMETER
SYMBOL CONDITIONS
MIN
TYP
3.3
MAX
UNITS
INTERNAL SWITCH/CURRENT LIMIT
Peak Switch Current Limit
ILIM
(Note 3)
2.4
Switch Leakage Current
IOL
VIN = 76V, VON/OFF = 0V, VLX = 0V
-10
Switch On-Resistance
PFM Threshold
PFM Threshold
FB Input Bias Current
RDS(ON)
ISWITCH = 1A
IPFM
Minimum switch current in any cycle
1
IPFM
Minimum switch current in any cycle at
TJ ≤ +25°C (Note 4)
14
IB
MAX5090C, VFB = 1.2V
5.0
A
+10
µA
0.26
0.4
Ω
60
300
mA
300
mA
-150
+0.1
+150
nA
1.180
1.38
1.546
V
ON/OFF CONTROL INPUT
ON/OFF Input-Voltage
Threshold
VON/OFF Rising trip point
ON/OFF Input-Voltage
Hysteresis
VHYST
ON/OFF Input Current
ION/OFF
100
VON/OFF = 0V to VIN
mV
10
100
nA
127
150
kHz
200
kHz
OSCILLATOR/SYNCHRONIZATION
Oscillator Frequency
f0SC
Synchronization
fSYNC
Maximum Duty Cycle
DMAX
106
119
VIN = 6.5V to 76V, VOUT ≤ 11V
SYNC High-Level Voltage
80
95
%
2.0
V
SYNC Low-Level Voltage
0.8
V
SYNC Minimum Pulse Width
350
ns
+1
µA
SYNC Input Leakage
-1
INTERNAL VOLTAGE REGULATOR
Regulator Output Voltage
VD
Dropout Voltage
Load Regulation
∆VD/∆IVD
VIN = 9V to 76V, IOUT = 0
7.0
7.8
8.4
V
6.5V ≤ VIN ≤ 8.5V, IOUT = 15mA
0.5
V
0 to 15mA
10
Ω
30
°C/W
+175
°C
20
°C
PACKAGE THERMAL CHARACTERISTICS
Thermal Resistance
(Junction to Ambient)
θJA
TQFN package (JEDEC 51)
TSH
Temperature rising
THERMAL SHUTDOWN
Thermal-Shutdown Junction
Temperature
Thermal-Shutdown
Hysteresis
Note
Note
Note
Note
1:
2:
3:
4:
THYST
All limits at -40°C are guaranteed by design, not production tested.
For total current consumption during switching (at no load), also see the Typical Operating Characteristics.
Switch current at which the current-limit circuit is activated.
Limits are guaranteed by design.
www.maximintegrated.com
Maxim Integrated │ 3
MAX5090A/B/C
2A, 76V, High-Efficiency MAXPower
Step-Down DC-DC Converters
Typical Operating Characteristics
(VIN = 12V, VON/OFF =12V, TA = TJ = -40°C to +125°C, unless otherwise noted. Typical values are at TA = +25°C. See the Typical
Operating Circuit, if applicable.)
3.36
5.10
5.05
IOUT = 0
3.32
3.30
3.26
4.95
IOUT = 2A
3.24
-25
0
25
50
75
4.85
100 125 150
3.22
-50
-25
0
25
50
75
3.20
100 125 150
3.38
3.36
3.34
36
46
56
66
5.10
VOUT (V)
36
46
56
66
76
3.20
0.1
1
10
EFFICIENCY vs. LOAD CURRENT
(MAX5090AATE, VOUT = 3.3V)
90
80
EFFICIENCY (%)
VIN = 6.5V
VIN = 12V
VIN = 24V
VIN = 48V
VIN = 76V
VIN = 6.5V
70
VIN = 12V
60
VIN = 24V
50
VIN = 48V
40
VIN = 76V
30
10
800
1200
LOAD CURRENT (mA)
www.maximintegrated.com
1
10
1600
2000
0
0
400
800
1200
LOAD CURRENT (mA)
100
1000
10,000
OUTPUT CURRENT LIMIT
vs. TEMPERATURE (MAX5090AATE)
20
10
400
0.1
ILOAD (mA)
MAX5090 toc08
80
50
4.85
10,000
EFFICIENCY vs. LOAD CURRENT
(MAX5090BATE, VOUT = 5V)
100
MAX5090 toc07
90
60
1000
ILOAD (mA)
VIN (V)
70
100
1600
2000
4.0
OUTPUT CURRENT LIMIT (A)
26
VIN = 24V
VIN = 6.5V
4.90
3.22
16
5.00
4.95
VIN = 24V
VIN = 6.5V
VIN = 76V
3.5
MAX5090 toc09
VOUT (V)
3.30
76
5.15
3.24
0
26
5.05
VIN = 76V
3.32
3.26
4.90
20
16
MAX5090 toc06
3.40
3.28
30
6.5
LOAD REGULATION
(MAX5090BATE, VOUT = 5V)
IOUT = 2A
40
IOUT = 2A
3.24
LOAD REGULATION
(MAX5090AATE, VOUT = 3.3V)
4.95
EFFICIENCY (%)
3.26
LINE REGULATION
(MAX5090BATE, VOUT = 5V)
5.00
100
3.28
VIN (V)
IOUT = 0
6.5
3.30
AMBIENT TEMPERATURE (°C)
MAX5090 toc04
5.05
IOUT = 0
3.32
AMBIENT TEMPERATURE (°C)
5.10
VOUT (V)
IOUT = 2A
MAX5090 toc05
-50
5.15
0
3.34
4.90
3.22
4.85
3.36
5.00
3.28
3.20
3.38
IOUT = 0
VOUT (V)
VOUT (V)
3.34
LINE REGULATION
(MAX5090AATE, VOUT = 3.3V)
3.40
VOUT (V)
3.38
MAX5090 toc02
5.15
MAX5090 toc01
3.40
VOUT vs. TEMPERATURE
(MAX5090BATE, VOUT = 5V)
MAX5090 toc03
VOUT vs. TEMPERATURE
(MAX5090AATE, VOUT = 3.3V)
VOUT = 3.3V
5% DROP IN VOUT
PULSED OUTPUT LOAD
3.0
2.5
2.0
1.5
1.0
-50
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE (°C)
Maxim Integrated │ 4
MAX5090A/B/C
2A, 76V, High-Efficiency MAXPower
Step-Down DC-DC Converters
Typical Operating Characteristics (continued)
(VIN = 12V, VON/OFF =12V, TA = TJ = -40°C to +125°C, unless otherwise noted. Typical values are at TA = +25°C. See the Typical
Operating Circuit, if applicable.)
2.0
1.5
-25
0
25
50
75
3.0
2.0
1.0
100 125 150
6.5
16
26
NO-LOAD SUPPLY CURRENT vs. TEMPERATURE
(MAX5090AATE)
VOUT = 3.3V
500
450
400
350
-50
-25
0
25
50
75
600
4.0
3.0
2.0
1.0
76
500
450
400
350
6.5
16
26
SHUTDOWN CURRENT
vs. INPUT VOLTAGE
13
VOUT = 3.3V
35
36
46
56
66
6.5
16
26
36
46
56
66
76
SHUTDOWN CURRENT vs. TEMPERATURE
(MAX5090AATE)
76
30
VOUT = 3.3V
26
22
18
14
10
-50
-25
0
25
50
100 125 150 175
INPUT VOLTAGE (V)
AMBIENT TEMPERATURE (°C)
OUTPUT VOLTAGE
vs. INPUT VOLTAGE
LOAD-TRANSIENT RESPONSE
(MAX5090AATE)
MAX5090CATE
VOUT = 11V
VON/OFF = VIN
11
MAX5090 toc12
5.0
INPUT VOLTAGE (V)
550
300
100 125 150
MAX5090 toc16
MAX5090 toc18
VOUT = 3.3V
A
30
25
VOUT (V)
SHUTDOWN CURRENT (µA)
40
66
VOUT = 3.3V
AMBIENT TEMPERATURE (°C)
45
56
NO-LOAD SUPPLY CURRENT vs. INPUT VOLTAGE
(MAX5090AATE)
NO-LOAD SUPPLY CURRENT
MAX5090 toc13
NO-LOAD SUPPLY CURRENT (µA)
600
300
46
6.0
INPUT VOLTAGE (V)
AMBIENT TEMPERATURE (°C)
550
36
SHUTDOWN CURRENT (µA)
-50
4.0
MAX5090 toc14
1.0
5.0
VOUT = 5V
5% DROP IN VOUT
PULSED OUTPUT LOAD
MAX5090 toc15
2.5
6.0
7.0
OUTPUT CURRENT LIMIT (A)
3.0
VOUT = 3.3V
5% DROP IN VOUT
PULSED OUTPUT LOAD
MAX5090 toc17
3.5
7.0
MAX5090 toc11
VOUT = 5V
5% DROP IN VOUT
PULSED OUTPUT LOAD
OUTPUT CURRENT LIMIT vs. INPUT VOLTAGE
(MAX5090BATE)
OUTPUT CURRENT LIMIT vs. INPUT VOLTAGE
(MAX5090AATE)
OUTPUT CURRENT LIMIT (A)
OUTPUT CURRENT LIMIT (A)
4.0
MAX5090 toc010
OUTPUT CURRENT LIMIT vs. TEMPERATURE
(MAX5090BATE)
20
15
10
IOUT = 2A
IOUT = 1A
6
IOUT = 0A
B
3
5
0
9
6.5
16
26
36
46
56
INPUT VOLTAGE (V)
www.maximintegrated.com
66
76
0
5
6
7
8
9
10 11 11.5 12 12.5 13
VIN (V)
400µs/div
A: VOUT, 200mV/div, AC-COUPLED
B: IOUT, 1A/div, 1A TO 2A
Maxim Integrated │ 5
MAX5090A/B/C
2A, 76V, High-Efficiency MAXPower
Step-Down DC-DC Converters
Typical Operating Characteristics (continued)
(VIN = 12V, VON/OFF =12V, TA = TJ = -40°C to +125°C, unless otherwise noted. Typical values are at TA = +25°C. See the Typical
Operating Circuit, if applicable.)
LX WAVEFORMS
(MAX5090AATE)
LOAD-TRANSIENT RESPONSE
(MAX5090AATE)
MAX5090 toc19
LX WAVEFORMS
(MAX5090AATE)
MAX5090 toc20
MAX5090 toc21
VOUT = 3.3V
A
A
A
VOUT = 3.3V
VOUT = 3.3V
B
B
B
0
400µs/div
4µs/div
4µs/div
A: VOUT, 200mV/div, AC-COUPLED
B: IOUT, 500mA/div, 0.1A TO 1A
A: SWITCH VOLTAGE (LX PIN), 20mV/div (VIN = 48V)
B: INDUCTOR CURRENT, 2A/div (I0 = 2A)
LX WAVEFORM
(MAX5090AATE)
STARTUP WAVEFORM
(IOUT = 0)
STARTUP WAVEFORM
(IOUT = 2A)
MAX5090 toc23
MAX5090 toc22
A: SWITCH VOLTAGE, 20V/div (VIN = 48V)
B: INDUCTOR CURRENT, 200mA/div (I0 = 75mA)
MAX5090 toc24
VOUT = 3.3V
A
A
A
B
B
B
CSS = 0.047µF
4ms/div
4µs/div
PEAK SWITCH CURRENT
vs. INPUT VOLTAGE
MAX5090 toc25
PEAK SWITCH CURRENT (A)
5.0
A: VON/OFF, 2V/div
B: VOUT, 1V/div
SYNCHRONIZATION
MAX5090AATE
VOUT = 3.3V
5% DROP IN VOUT
PULSED OUTPUT LOAD
6.0
4ms/div
A: VON/OFF, 2V/div
B: VOUT, 1V/div
A: SWITCH VOLTAGE, 20V/div (VIN = 48V)
B: INDUCTOR CURRENT, 200mA/div (IOUT = 0)
7.0
CSS = 0.047µF
SYNCHRONIZATION
MAX5090 toc26
fSYNC = 119kHz
MAX5090 toc27
fSYNC = 200kHz
SYNC
2V/div
SYNC
2V/div
LX
10V/div
LX
10V/div
4.0
3.0
2.0
1.0
6.5
16
26
36
46
56
66
76
2µs/div
1µs/div
INPUT VOLTAGE (V)
www.maximintegrated.com
Maxim Integrated │ 6
MAX5090A/B/C
2A, 76V, High-Efficiency MAXPower
Step-Down DC-DC Converters
Pin Description
PIN
NAME
FUNCTION
1, 2
LX
3
BST
Source Connection of Internal High-Side Switch
4
VIN
Input Voltage. Bypass VIN to SGND with a low-ESR capacitor as close as possible to the device.
5
VD
Internal Regulator Output. Bypass VD to PGND with a 3.3µF/10V or greater ceramic capacitor.
6
SYNC
7
SS
Soft-Start Capacitor Connection. Connect an external capacitor from SS to SGND to adjust the
soft-start time.
8
FB
Output Sense Feedback Connection.
For fixed output voltage (MAX5090A/MAX5090B), connect FB to VOUT.
For adjustable output voltage (MAX5090C), use an external resistive voltage-divider to set VOUT.
VFB regulating set point is 1.228V.
9
ON/OFF
10
SGND
Boost Capacitor Connection. Connect a 0.22µF ceramic capacitor from BST to LX.
Synchronization Input. Connect SYNC to an external clock for synchronization. Connect to SGND to
select the internal 127kHz switching frequency.
Shutdown Control Input. Pull ON/OFF low to put the device in shutdown mode. Drive ON/OFF high for
normal operation. Connect ON/OFF to VIN with short leads for always-on operation.
Signal Ground. SGND must be connected to PGND for proper operation.
11, 15, 16
N.C.
12
PGND
No Connection. Not internally connected.
Power Ground
13, 14
DRAIN
Internal High-Side Switch Drain Connection
—
EP
Exposed Pad. Solder EP to SGND plane to aid in heat dissipation. Do not use as the only electrical
ground connection.
Detailed Description
The MAX5090 step-down DC-DC converter operates from
a 6.5V to 76V input voltage range. A unique voltage-mode
control scheme with voltage feed-forward and an internal
switching DMOS FET provides high efficiency over a wide
input voltage range. This pulse-width-modulated converter operates at a fixed 127kHz switching frequency or can
be synchronized with an external system clock frequency.
The device also features automatic pulse-skipping mode
to provide high efficiency at light loads. Under no load,
the MAX5090 consumes only 310µA, and in shutdown
mode, consumes only 20µA. The MAX5090 also features
undervoltage-lockout, hiccup-mode output short-circuit
protection and thermal shutdown.
ON/OFF/Undervoltage Lockout (UVLO)
Use the ON/OFF function to program the external UVLO
threshold at the input. Connect a resistive voltage-divider
from VIN to SGND with the center node to ON/OFF, as
shown in Figure 1. Calculate the threshold value by using
the following formula:
www.maximintegrated.com
R1
VUVLO(TH) =
1 + R2 × 1.38
Set the external VUVLO(TH) to greater than 6.45V. The
maximum recommended value for R2 is less than 1MΩ.
ON/OFF is a logic input and can be safely driven to the full
VIN range. Connect ON/OFF to VIN for automatic startup.
Drive ON/OFF to ground to shut down the MAX5090.
Shutdown forces the internal power MOSFET off, turns off
all internal circuitry, and reduces the VIN supply current to
20µA (typ). The ON/OFF rising threshold is 1.546V (max).
Before any operation begins, the voltage at ON/OFF must
exceed 1.546V. The ON/OFF input has 100mV hysteresis.
If the external UVLO threshold-setting divider is not used,
an internal undervoltage-lockout feature monitors the
supply voltage at VIN and allows the operation to start
when VIN rises above 6.45V (max). The internal UVLO
rising threshold is set at 6.17V with 0.5V hysteresis.
The VIN and VON/OFF voltages must be above 6.5V and
1.546V, respectively, for proper operation.
Maxim Integrated │ 7
MAX5090A/B/C
2A, 76V, High-Efficiency MAXPower
Step-Down DC-DC Converters
Simplified Functional Diagram
ON/OFF
ENABLE
1.38V
VD
DRAIN
VIN
REGULATOR
(FOR DRIVER)
REGULATOR
(FOR ANALOG)
IREF-PFM
CPFM
HIGH-SIDE
CURRENT SENSE
OSC
VREF
RAMP
CILIM
IREF-LIM
CLKI
RMP
BST
SRMP
SYNC
SRAMP
SCK
MUX
MAX5090
SS
CLK
MIN
FB
RAMP
*RH
x1
N
LX
TYPE 3
COMPENSATION
*RL
CONTROL
LOGIC
EAMP
CPWM
THERMAL
SHUTDOWN
PGND
*RH = 0Ω AND RL = ∞ FOR MAX5090C
SGND
www.maximintegrated.com
Maxim Integrated │ 8
MAX5090A/B/C
Boost High-Side Gate Drive (BST)
Connect a flying bootstrap capacitor between LX and
BST to provide the gate-drive voltage to the high-side
n-channel DMOS switch. The capacitor is alternately
charged from the internally regulated output-voltage
VD and placed across the high-side DMOS driver. Use
a 0.22µF, 16V ceramic capacitor located as close as
possible to the device.
On startup, an internal low-side switch connects LX to
ground and charges the BST capacitor to (VD - VDIODE).
Once the BST capacitor is charged, the internal lowside switch is turned off and the BST capacitor voltage
provides the necessary enhancement voltage to turn on
the high-side switch.
Synchronization (SYNC)
SYNC controls the oscillator frequency. Connect SYNC to
SGND to select 127kHz operation. Use the SYNC input
to synchronize to an external clock. SYNC has a guaranteed 119kHz to 200kHz frequency range when using an
external clock.
When SYNC is connected to SGND, the internal clock is
used to generate a ramp with the amplitude in proportion
to VIN and the period corresponding to the internal clock
frequency to modulate the duty cycle of the high-side
switch.
If an external clock (SYNC clock) is applied at SYNC
for four cycles, the MAX5090 selects the SYNC clock.
The MAX5090 generates a ramp (SYNC ramp) with
the amplitude in proportion to VIN and the period
corresponding to the SYNC clock frequency. The MAX5090
initially blanks the SYNC ramp for 375µs (typ) to allow the
ramp to reach its target amplitude (proportion to the VIN
supply). After the SYNC blanking time, the SYNC ramps
and the SYNC clock switches to the PWM controller
and replaces the internal ramp and the internal clock,
respectively. If the SYNC clock is removed for three
internal clock cycles, the internal clock and the internal
ramp switch back to the PWM controller.
The minimum pulse-width requirement for the external
clock is 350ns, and if the requirement is not met, the
MAX5090 could ignore the clock as a noisy bounce.
www.maximintegrated.com
2A, 76V, High-Efficiency MAXPower
Step-Down DC-DC Converters
Soft-Start (SS)
The MAX5090 provides the flexibility to externally
program a suitable soft-start time for a given application.
Connect an external capacitor from SS to SGND to use
the external soft-start. Soft-start gradually ramps up the
reference voltage seen by the error amplifier to control
the output’s rate of rise and reduce the input surge current
during startup. For soft-start time longer than 700µs, use
the following equation to calculate the soft-start capacitor
(CSS) required for the soft-start time (tSS):
C SS =
10 × 10 −6 × t SS
1.46
where tSS > 700µs and CSS is in Farads.
The MAX5090 also provides an internal soft-start (700µs,
typ) with a current source to charge an internal capacitor
to rise up to the bandgap reference voltage. The internal
soft-start voltage will eventually be pulled up to 3.4V. The
internal soft-start reference also feeds to the error amplifier. The error amplifier takes the lowest voltage among
SS, the internal soft-start voltage, and the bandgap
reference voltage as the input reference for VOUT.
Soft-start occurs when power is first applied and when
the device exits shutdown. The MAX5090 also goes
through soft-start when coming out of thermal-overload
protection. During a soft-start, if the voltage at SS (VSS)
is charged up to 1.46V in less than 700µs, the MAX5090
takes its default internal soft-start (700µs) to ramp up as
its reference. After the SS and the internal soft-start ramp
up over the bandgap reference, the error amplifier takes
the bandgap reference.
Thermal-Overload Protection
The MAX5090 features integrated thermal-overload
protection. Thermal-overload protection limits power
dissipation in the device, and protects the device from a
thermal overstress. When the die temperature exceeds
+175°C, an internal thermal sensor signals the shutdown logic, turning off the internal power MOSFET,
resetting the internal soft-start, and allowing the IC
to cool. The thermal sensor turns the internal power
MOSFET back on after the IC’s die temperature cools
down to +155°C, resulting in a pulsed output under
continuous thermal-overload conditions.
Maxim Integrated │ 9
MAX5090A/B/C
2A, 76V, High-Efficiency MAXPower
Step-Down DC-DC Converters
VIN
6.5V TO 76V
R1
CIN
68µF
RIN
10Ω
CBYPASS
0.47µF
VIN
DRAIN
VOUT
3.3V, 2A
D1
PDS5100H
COUT
100µF
LX
ON/OFF
0.22µF
MAX5090A
R2
100µH
BST
FB
SS
SYNC
SGND
0.047µF
VD
PGND
3.3µF
Figure 1. Fixed Output-Voltage Configuration
VIN
7.5V TO 76V
CIN
68µF
RIN
10Ω
CBYPASS
0.47µF
VIN
DRAIN
VOUT
5.25V, 2A
100µH
LX
ON/OFF
0.22µF
MAX5090C
D1
PDS5100H
R3
0.047µF
R4
BST
COUT
100µF
FB
SS
SYNC
SGND
PGND
VD
3.3µF
Figure 2. Adjustable Output-Voltage Configuration
www.maximintegrated.com
Maxim Integrated │ 10
MAX5090A/B/C
Thermal-overload protection is intended to protect the
MAX5090 in the event of a fault condition. For normal
circuit operation, do not exceed the absolute maximum
junction temperature rating of TJ = +150°C.
Setting the Output Voltage
The MAX5090A/MAX5090B have preset output voltages
of 3.3V and 5.0V, respectively. Connect FB to VOUT for
the preset output voltage (Figure 1).
The MAX5090C offers an adjustable output voltage. Set
the output voltage with a resistive divider connected from
the circuit’s output to ground (Figure 2). Connect the
center node of the divider to FB. Choose R4 less than
15kΩ, then calculate R3 as follows:
=
R3
(VOUT − 1.228)
× R4
1.228
The MAX5090 features internal compensation for
optimum closed-loop bandwidth and phase margin.
Because of the internal compensation, the output must
be sensed immediately after the primary LC.
Inductor Selection
The MAX5090 is a fixed-frequency converter with fixed
internal frequency compensation. The internal fixed
compensation assumes a 100µH inductor and 100µF
output capacitor with 50mΩ ESR. It relies on the location
of the double LC pole and the ESR zero frequency for
proper closed-loop bandwidth and the phase margin at the
closed-loop unity-gain frequency. See Table 2 for proper
component values. Usually, the choice of an inductor is
guided by the voltage difference between VIN and VOUT,
the required output current, and the operating frequency
of the circuit. However, use the recommended inductors
in Table 2 to ensure stable operation with optimum bandwidth.
Use an inductor with a maximum saturation current rating
greater than or equal to the maximum peak current limit
(5A). Use inductors with low DC resistance for a higher
efficiency converter.
Selecting a Rectifier
The MAX5090 requires an external Schottky rectifier as
a freewheeling diode. Connect this rectifier close to the
device using short leads and short PCB traces. The rectifier diode must fully conduct the inductor current when the
www.maximintegrated.com
2A, 76V, High-Efficiency MAXPower
Step-Down DC-DC Converters
Table 1. Diode Selection
VIN (V)
DIODE PART
NUMBER
B340LB
6.5 to 36
RB051L-40
MBRS340T3
6.5 to 56
Diodes Inc.
Central Semiconductor
ON Semiconductor
MBRM560
Diodes Inc.
RB095B-60
Central Semiconductor
MBRD360T4
6.5 to 76
MANUFACTURER
50SQ80
PDS5100H
ON Semiconductor
IR
Diodes Inc.
power FET is off to have a full rectifier function. Choose a
rectifier with a continuous current rating greater than the
highest expected output current. Use a rectifier with a
voltage rating greater than the maximum expected input
voltage, VIN. Use a low forward-voltage Schottky rectifier
for proper operation and high efficiency. Avoid higher than
necessary reverse-voltage Schottky rectifiers that have
higher forward-voltage drops. Use a Schottky rectifier with
forward-voltage drop (VF) less than 0.55V and 0.45V at +25°C
and +125°C, respectively, and at maximum load current to
avoid forward biasing of the internal parasitic body diode
(LX to ground). See Figure 3 for forward-voltage drop vs.
temperature of the internal body diode of the MAX5090.
Internal parasitic body-diode conduction may cause improper
operation, excessive junction temperature rise, and thermal
shutdown. Use Table 1 to choose the proper rectifier at
different input voltages and output current.
Input Bypass Capacitor
The discontinuous input current waveform of the buck
converter causes large ripple currents in the input capacitor. The switching frequency, peak inductor current, and
the allowable peak-to-peak voltage ripple reflecting back
to the source dictate the capacitance requirement. The
MAX5090 high-switching frequency allows the use of
smaller-value input capacitors.
The input ripple is comprised of ∆VQ (caused by the
capacitor discharge) and ∆VESR (caused by the ESR
of the capacitor). Use low-ESR aluminum electrolytic
capacitors with high-ripple current capability at the input.
Assuming that the contribution from the ESR and capacitor discharge is equal to 90% and 10%, respectively,
Maxim Integrated │ 11
MAX5090A/B/C
2A, 76V, High-Efficiency MAXPower
Step-Down DC-DC Converters
calculate the input capacitance and the ESR required for
a specified ripple using the following equations:
∆VESR
∆IL
I OUT + 2
I OUT × D(1 − D)
C IN =
∆VQ × f SW
800
700
ESR IN =
VF_D1 (mV)
where:
600
(V − VOUT ) × VOUT
∆IL = IN
VIN × f SW × L
D=
0
Low-ESR ceramic multilayer chip capacitors are
recommended for size-optimized application. For ceramic
capacitors, assume the contribution from ESR and capacitor discharge is equal to 10% and 90%, respectively.
The input capacitor must handle the RMS ripple current
without significant rise in the temperature. The maximum
capacitor RMS current occurs at approximately 50% duty
cycle. Ensure that the ripple specification of the input
capacitor exceeds the worst-case capacitor RMS ripple
current. Use the following equations to calculate the input
capacitor RMS current:
where:
IPRMS =+
(IPK 2 I
I AVGin =
2
AVGin 2
DC + IPK ×IDC
)×
D
3
VOUT × I OUT
VIN × η
∆IL
2
∆IL
IDC I OUT −
=
2
VOUT
D=
VIN
IPK I OUT +
=
IPRMS is the input switch RMS current, IAVGin is the input
average current, and h is the converter efficiency.
www.maximintegrated.com
300
100
VOUT
VIN
IPRMS 2 − I
400
200
IOUT is the maximum output current of the converter and
fSW is the oscillator switching frequency (127kHz). For
example, at VIN = 48V, VOUT = 3.3V, the ESR and input
capacitance are calculated for the input peak-to-peak
ripple of 100mV or less, yielding an ESR and capacitance
value of 40mΩ and 100µF, respectively.
=
I CRMS
500
-40
25
100
125
150
TEMPERATURE (°C)
Figure 3. Forward-Voltage Drop vs. Temperature of the Internal
Body Diode of MAX5090
The ESR of the aluminum electrolytic capacitor increases
significantly at cold temperatures. Use a 1µF or greater value
ceramic capacitor in parallel with the aluminum electrolytic
input capacitor, especially for input voltages below 8V.
Output Filter Capacitor
The output capacitor (COUT) forms double pole with
the inductor and a zero with its ESR. The MAX5090’s
internal fixed compensation is designed for a 100µF
capacitor, and the ESR must be from 20mΩ to 100mΩ. The
use of an aluminum or tantalum electrolytic capacitor is
recommended. See Table 2 to choose an output capacitor
for stable operation.
The output ripple is comprised of ∆VOQ (caused by the
capacitor discharge), and ∆VOESR (caused by the ESR
of the capacitor). Use low-ESR tantalum or aluminum
electrolytic capacitors at the output. Use the following
equations to calculate the contribution of output capacitance and its ESR on the peak-to-peak output rip voltage:
∆VOESR =
∆IL × ESR
∆IL
∆VOQ ≈
8 × C OUT × f SW
The MAX5090 has a programmable soft-start time (tSS).
The output rise time is directly proportional to the output
capacitor, output voltage, and the load. The output rise time
also depends on the inductor value and the current-limit
threshold. It is important to keep the output rise time at
startup the same as the soft-start time (tSS) to avoid output
Maxim Integrated │ 12
MAX5090A/B/C
overshoot. Large output capacitors take longer than the
programmed soft-start time (tSS) and cause error-amplifier
saturation. This results in output overshoot. Use greater
than 2ms soft-start time for a 100µF output capacitor.
In a dynamic-load application, the allowable deviation of
the output voltage during the fast transient load dictates
the output capacitance value and the ESR. The output
capacitors supply the step-load current until the controller
responds with a greater duty cycle. The response time
(tRESPONSE) depends on the closed-loop bandwidth
of the converter. The resistive drop across the capacitor ESR and capacitor discharge cause a voltage droop
during a step-load. Use a combination of low-ESR
tantalum and ceramic capacitors for better transient
load and ripple/noise performance. Use the following
equations to calculate the deviation of output voltage due
to the ESR and capacitance value of the out capacitor:
2A, 76V, High-Efficiency MAXPower
Step-Down DC-DC Converters
Board Layout Guidelines
1) Minimize ground noise by connecting the anode of the
Schottky rectifier, the input bypass capacitor ground
lead, and the output filter capacitor ground lead to a
large PGND plane.
2) Minimize lead lengths to reduce stray capacitance,
trace resistance, and radiated noise. In particular,
place the Schottky rectifier diode right next to the
device. Also, place the BST and VD bypass capacitors
very close to the device.
∆VOESR =I STEP × ESR OUT
3) Connect the exposed pad of the IC to the SGND plane.
Do not make a direct connection between the exposed
pad plane and SGND (pin 7) under the IC. Connect
the exposed pad and pin 7 to the SGND plane separately. Connect the ground connection of the feedback
resistive divider, ON/OFF threshold resistive divider,
and the soft-start capacitor to the SGND plane.
Connect the SGND plane and PGND plane at one
point near the input bypass capacitor at VIN.
I STEP × t RESPONSE
∆VOQ =
C OUT
4) Use large SGND plane as a heatsink for the MAX5090.
Use large PGND and LX planes as heatsinks for the
rectifier diode and the inductor.
where ISTEP is the load step and tRESPONSE is the
response time of the controller. Controller response time
is approximately one-third of the reciprocal of the closedloop unity-gain bandwidth, 20kHz typically.
www.maximintegrated.com
Maxim Integrated │ 13
MAX5090A/B/C
2A, 76V, High-Efficiency MAXPower
Step-Down DC-DC Converters
Application Circuit
VIN
CIN
R1
RIN
CBYPASS
VIN
DRAIN
L1
LX
ON/OFF
MAX5090B
R2
CBST
D1
VOUT
COUT
BST
FB
SS
SYNC
SGND
PGND
VD
CSS
3.3µF
Figure 4. Fixed Output Voltage
Table 2. Typical External Components Selection (Circuit of Figure 4)
VIN (V)
6.5 to 76
7.5 to 76
www.maximintegrated.com
VOUT (V)
3.3
5
IOUT (A)
EXTERNAL COMPONENTS
2
MAX5090AATE
CIN = 2 x 68µF/100V EEVFK2A680Q, Panasonic
CBYPASS = 0.47µF/100V, GRM21BR72A474KA, Murata
COUT = 220µF/6.3V 6SVP220MX, Sanyo
CBST = 0.22µF/16V, GRM188R71C224K, Murata
R1 = 0Ω
R2 = Open
RIN = 10Ω, ±1%, 0603
D1 = PDS5100H, Diodes Inc.
L1 = 47µH, DO5022P-473
2
MAX5090BATE
CIN = 2 x 68µF/100V EEVFK2A680Q, Panasonic
CBYPASS = 0.47µF/100V, GRM21BR72A474KA, Murata
COUT = 100µF/6.3V 6SVP100M, Sanyo
CBST = 0.22µF/16V, GRM188R71C224K, Murata
R1 = 0Ω
R2 = Open
RIN = 10Ω, ±1%, 0603
D1 = PDS5100H, Diodes Inc.
L1 = 47µH, DO5022P-473
Maxim Integrated │ 14
MAX5090A/B/C
2A, 76V, High-Efficiency MAXPower
Step-Down DC-DC Converters
Table 2. Typical External Components Selection (Circuit of Figure 4) (continued)
VIN (V)
6.5 to 40
7.5 to 40
15 to 40
VOUT (V)
IOUT (A)
3.3
5
11
EXTERNAL COMPONENTS
2
MAX5090AATE
CIN = 330µF/50V EEVFK1H331Q, Panasonic
CBYPASS = 0.47µF/50V, GRM21BR71H474KA, Murata
COUT = 100µF/6.3V 6SVP100M, Sanyo
CBST = 0.22µF/16V, GRM188R71C224K, Murata
R1 = 0Ω
R2 = Open
RIN = 10Ω, ±1%, 0603
D1 = B360, Diodes Inc.
L1 = 100µH, DO5022P-104
2
MAX5090BATE
CIN = 330µF/50V EEVFK1H331Q, Panasonic
CBYPASS = 0.47µF/50V, GRM21BR71H474KA, Murata
COUT = 100µF/6.3V 6SVP100M, Sanyo
CBST = 0.22µF/16V, GRM188R71C224K, Murata
R1 = 0Ω
R2 = Open
RIN = 10Ω, ±1%, 0603
D1 = B360, Diodes Inc
L1 = 100µH, DO5022P-104
2
MAX5090CATE (VOUT programmed to 11V)
CIN = 330μF/50V EEVFK1H331Q, Panasonic
CBYPASS = 0.47μF/50V, GRM21BR71H474KA, Murata
COUT = 100μF/16V 16SVP100M, Sanyo
CBST = 0.22μF/16V, GRM188R71C224K, Murata
R1 = 910kΩ
R2 = 100kΩ
R3 = 88.2kΩ, ±1% (0603)
R4 = 10kΩ, ±1% (0603)
RIN = 10Ω, ±1% (0603)
D1 = B360, Diodes Inc.
L1 = 100μH, DO5022P-104
Table 3. Component Suppliers
SUPPLIER
WEBSITE
AVX
www.avxcorp.com
Coilcraft
www.coilcraft.com
Diodes Incorporated
www.diodes.com
Panasonic
www.panasonic.com
Sanyo
www.sanyo.com
TDK
www.component.tdk.com
Vishay
www.vishay.com
www.maximintegrated.com
Maxim Integrated │ 15
MAX5090A/B/C
VIN
12V
2A, 76V, High-Efficiency MAXPower
Step-Down DC-DC Converters
CIN
68µF
RIN
CBYPASS
VIN
DRAIN
LX
ON/OFF
PTC
Rt
MAX5090B
Ct
VOUT
5V, 2A
100µH
CBST
D1
B360
COUT
100µF
BST
FB
SS
SYNC
SGND
PGND
VD
CSS
3.3µF
*LOCATE PTC AS CLOSE TO HEAT-DISSIPATING COMPONENT AS POSSIBLE.
Figure 5. Load-Temperature Monitoring with ON/OFF (Requires Accurate VIN)
Ordering Information (continued)
PART
TEMP
RANGE
PINPACKAGE
MAX5090CATE+ -40°C to +125°C 16 TQFN-EP*
MAX5090CATE -40°C to +125°C 16 TQFN-EP*
+Denotes a lead(Pb)-free/RoHS-compliant package.
*EP = Exposed pad.
Package Information
OUTPUT
VOLTAGE
(V)
Adj
Adj
For the latest package outline information and land patterns
(footprints), go to www.maximintegrated.com/packages. Note
that a “+”, “#”, or “-” in the package code indicates RoHS status
only. Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
16 TQFN
T1655+3
21-0140
—
Chip Information
PROCESS: BCD
TRANSISTOR COUNT: 7893
www.maximintegrated.com
Maxim Integrated │ 16
MAX5090A/B/C
2A, 76V, High-Efficiency MAXPower
Step-Down DC-DC Converters
Revision History
REVISION
NUMBER
REVISION
DATE
PAGES
CHANGED
0
3/06
Initial release
—
1
9/14
No /V OPNs; Removed automotive reference from Applications section
1
DESCRIPTION
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits)
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
© 2014 Maxim Integrated Products, Inc. │ 17
工商网监
湘ICP备2023018690号
