MAX5097AEVKIT+

19-0718; Rev 0; 1/07 MAX5097A Evaluation Kit The MAX5097A evaluation kit (EV kit) demonstrates the MAX5097A in a standard application circuit demonstrating high efficiency. The EV kit circuit features a MAX5097A IC in a 16-pin TQFN package. The EV kit can operate from a 5V to 40V input source. The MAX5097A EV kit includes a current-mode DC-DC step-down regulator (Buck Mode) and a selectable lowquiescent-current LDO regulator for operation at lightload (LDO Mode). The step-down regulator provides a 3.3V output with up to 600mA output current. In LDO Mode, the MAX5097A IC provides up to 100mA output current. The EV kit circuit’s step-down regulator operates at a switching frequency of 330kHz, thus allowing the use of small ceramic capacitors at the output. The MAX5097A is capable of synchronizing to an external digital clock. The MAX5097A EV kit can be reconfigured for other output voltages by selecting appropriate external components. The EV kit circuit features soft-start, output current-limit, and an open-drain active-low reset output PCB pad. Features ♦ 5V to 40V Input Voltage (Buck Mode) ♦ 4V to 40V Input Voltage (LDO Mode) ♦ 3.3V Output at Up to 600mA (Buck Mode) ♦ Low Quiescent Current 3.3V Output at Up to 100mA (LDO Mode) ♦ Configurable Output Voltage ♦ 330kHz Switching Frequency ♦ Capable of Synchronizing to an External Clock ♦ Open-Drain RESET Output PCB Pad ♦ Surface-Mount Components ♦ Fully Assembled and Tested Ordering Information PART TEMP RANGE IC PACKAGE MAX5097AEVKIT+ 0°C to +70°C* 16 TQFN-EP +Denotes a lead-free and RoHS-compliant EV kit. *This limited temperature range applies to the EV kit PCB only. The MAX5097A IC temperature range is -40°C to +125°C. Component List DESIGNATION QTY C1 1 C2 C3 C4 C5 DESCRIPTION DESIGNATION QTY 150µF, 50V electrolytic capacitor (8mm x 10.2mm) Panasonic EEVFK1H151P C8 1 0.047µF ±10%, 50V X7R ceramic capacitor (0603) Murata GRM188R71H473K 1 0.22µF ±10%, 50V X5R ceramic capacitor (0805) Murata GRM21BR71H224K D1 1 2.0A, 60V high-speed switching diode (SMA) Diodes Inc MURS120-13-F JU1, JU2 2 2-pin headers 1 22µF ±20%, 6.3V X5R ceramic capacitor (1206) Murata GRM31CR60J226M JU3 1 3-pin header L1 1 22µH, 1.6A inductor Sumida CDRH8D28-220NP R1 0 Not installed, resistor (0603) R2 1 0Ω ±5% resistor (0603) R3 1 100kΩ ±1% resistor (0603) R4, R5, R7 3 100kΩ ±5% resistors (0603) R6 1 10kΩ ±5% resistor (0603) U1 1 40V input, 330kHz step-down converter with LDO MAX5097AATE+ (16-pin, 5mm x 5mm thin QFN-EP) — 3 Shunts — 1 PCB: MAX5097AEVKIT+ 1 1 1200µF ±5%, 50V C0G ceramic capacitor (0603) Murata GRM1885C1H122J 22pF ±5%, 50V C0G ceramic capacitor (0603) Murata GRM1885C1H220J C6 1 0.01µF ±10%, 50V X7R ceramic capacitor (0603) Murata GRM188R71H103K C7 1 1µF ±10%, 10V X5R ceramic capacitor (0603) Murata GRM188R61A105K DESCRIPTION ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 Evaluates: MAX5097A General Description Evaluates: MAX5097A MAX5097A Evaluation Kit Detailed Description Component Suppliers SUPPLIER PHONE WEBSITE Diodes Inc. 805-446-4800 www.diodes.com Murata 770-436-1300 www.murata.com Panasonic 714-373-7366 www.panasonic.com Sumida 847-545-6700 www.sumida.com Note: Indicate that you are using the MAX5097A when contacting these component suppliers. Quick Start The MAX5097A EV kit is fully assembled and tested. Follow these steps to verify board operation. Caution: Do not turn on the power supply until all connections are completed. Required Equipment • 5V to 40V, 1A rated DC power supply • One voltmeter, one ammeter • Electronic load, such as an HP 6060B Output Startup 1) Verify that a shunt is installed across jumpers JU1 (LDO/BUCK, Buck Mode enabled) and JU2 (SYNC, 330kHz). 2) Verify that a shunt is installed across pins 1-2 of jumper JU3 (EN, input enabled). 3) Connect the electronic load positive terminal to the VOUT pad and connect the load’s negative terminal to the PGND pad. The MAX5097A EV kit includes a high-efficiency current-mode DC-DC step-down regulator (Buck Mode) and a selectable low-quiescent-current LDO regulator (LDO Mode). The EV kit circuit features a MAX5097A IC in a 16-pin TQFN exposed paddle package. The MAX5097A EV kit operates from a 5V to 40V input range DC source that can provide the EV kit with 1A or more of current. The Buck Mode regulator provides a 3.3V output at up to 600mA output current. An internal p-channel MOSFET works as a pass element when in LDO Mode and delivers up to 100mA of load current. Resistors R1 and R2 set the output voltage at VOUT. The output voltage can be adjusted from 1.24V to 11V by selecting appropriate resistors. The EV kit’s Buck Mode regulator operates at a switching frequency of 330kHz or the circuit can be configured to synchronize with an external clock by removing jumper JU2. When configured for synchronizing mode, an external TTL square-wave clock is used to synchronize and set the switching frequency up to 500kHz. SYNC and SGND PCB pads are provided for connecting the external clock. See the Clock Synchronization section for more information on the external clock. Capacitor C8 sets the soft-start feature. An open-drain active-low RESET PCB pad is provided for interfacing. The RESET pad is pulled up to VOUT by resistor R4, and jumper JU3 controls the shutdown mode that reduces the MAX5097A IC shutdown current to 6µA (typ). Jumper Selection and VOUT Reconfiguration 4) Connect the voltmeter to the VOUT and PGND pads. 5) Connect the power-supply positive terminal to the VIN pad and connect the supply ground to the PGND pad. 6) Enable the electronic load output and set it to 80mA current loading. 7) Turn on the power supply and set it to 12V. Step-Down and Low-Quiescent-Current LDO Regulators The MAX5097A EV kit features two modes for regulating the output; a Buck Mode regulator or a low-quiescent-current LDO Mode regulator. The 2-pin jumper, JU1, selects the mode of operation for the EV kit. Table 1 lists the selectable jumper options. 8) Verify that VOUT is 3.3V. 9) Remove the shunt from jumper JU1 and verify that the LDO regulator output (VOUT) is 3.3V. For instructions on selecting the feedback resistors for other output voltages, see the Evaluating Other Output Voltages section. 2 Table 1. Operation Mode JU1 Functions SHUNT LOCATION LDO/BUCK PIN MAX5097A OPERATION MODE Open Connected to BP with R7 LDO regulator (100mA max) Installed Connected to SGND Buck Mode regulator (600mA max) _______________________________________________________________________________________ MAX5097A Evaluation Kit Table 2. Clock JU2 Functions SHUNT LOCATION SYNC PIN EV KIT OPERATING MODE None Connected to external clock source Synchronization mode: Synchronized to an external clock frequency* Installed Connected to SGND Internal oscillator, 330kHz *The TTL clock source must provide the following signal qualities: Output voltage: • Logic-low = 0 to 0.8V • Logic-high = 2.0V to 5.5V Output frequency = 330kHz (synchronization range is 300kHz to 500kHz, refer to the MAX5097A data sheet for more information) Minimum pulse: 250ns (min) pulse width (high or low) Connect the external square-wave clock to the SYNC and SGND PCB pads. Shutdown Control The MAX5097A EV kit has a jumper to control the shutdown mode and thus reduce the MAX5097A current consumption. The 3-pin jumper, JU3, selects the shutdown mode for the MAX5097A circuit. Table 3 lists the jumper options. Table 3. Shutdown JU3 Functions EV KIT OPERATING MODE SHUNT LOCATION EN PIN 2-3 Connected to R5 Shutdown, VOUT = disabled 1-2 Connected to VIN Enabled, VOUT = enabled — Connected to an external controller External controller determines mode, enabled = high Evaluating Other Output Voltages The MAX5097A EV kit’s step-down DC-DC converter output (VOUT) is set to 3.3V by connecting the MAX5097A ADJ pin to SGND. To generate output voltages other than 3.3V (1.24V to 11V), select different voltage-divider resistors (R1, R2). Additionally, inductor L1, input and output capacitors C1, C3, and compensation components R3, C4, and C5 should be evaluated. Refer to the MAX5097A data sheet for information on selecting all these components. _______________________________________________________________________________________ 3 Evaluates: MAX5097A Clock Synchronization The MAX5097A EV kit has a PCB pad that enables the circuit to synchronize with an external TTL square-wave clock source. The 2-pin jumper, JU2, is provided to connect the MAX5097A SYNC pin to SGND for noise immunity. To synchronize the Buck Converter to an external clock, remove jumper JU2 and connect the TTL clock to the PCB SYNC pad. JU2 selects the clock synchronization or internal frequency for the MAX5097A. Table 2 lists the jumper options. Evaluates: MAX5097A MAX5097A Evaluation Kit VIN VIN C2 0.22μF C1 150μF 50V PGND BP 15 IN R7 100kΩ LDO/BUCK SGND 9 16 IN LX LDO/BUCK JU1 LX PGND SYNC SGND 5 13 14 VOUT VOUT C3 22μF D1 PGND 1 SYNC R6 10kΩ JU2 L1 22μH U1 VIN EN 1 2 3 R5 100kΩ VOUT MAX5097A JU3 12 6 EN R1 OPEN SS C8 0.047μF 2 OUT 11 ADJ 10 SGND R2 0Ω BP 4 BP C7 1.0μF VOUT R4 100kΩ RESET COMP 7 CT C6 0.01μF 3 8 R3 100kΩ 1% C4 1200pF C5 22pF RESET Figure 1. MAX5097A EV Kit Schematic 4 _______________________________________________________________________________________ MAX5097A Evaluation Kit Evaluates: MAX5097A Figure 2. MAX5097A EV Kit Component Placement Guide— Component Side Figure 3. MAX5097A EV Kit PCB Layout—Component Side Figure 4. MAX5097A EV Kit PCB Layout—GND Layer 2 _______________________________________________________________________________________ 5 Evaluates: MAX5097A MAX5097A Evaluation Kit Figure 5. MAX5097A EV Kit PCB Layout—VCC Layer 3 Figure 6. MAX5097A EV Kit PCB Layout—Solder Side Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 6 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2007 Maxim Integrated Products Janet Freed is a registered trademark of Maxim Integrated Products, Inc.