Click here for production status of specific part numbers.
MAX6316–MAX6322
5-Pin μP Supervisory Circuits with
Watchdog and Manual Reset
General Description
The MAX6316–MAX6322 family of microprocessor (μP)
supervisory circuits monitors power supplies and microprocessor activity in digital systems. It offers several combinations of push/pull, open-drain, and bidirectional (such
as Motorola 68HC11) reset outputs, along with watchdog
and manual reset features. The Selector Guide below lists
the specific functions available from each device.
These devices are available in 26 factory-trimmed reset
threshold voltages (from 2.5V to 5V, in 100mV increments),
featuring four minimum power-on reset timeout periods
(from 1ms to 1.12s), and four watchdog timeout periods
(from 6.3ms to 25.6s). Thirteen standard versions are
available with an order increment requirement of 2500
pieces (see Standard Versions table); contact the factory
for availability of other versions, which have an order
increment requirement of 10,000 pieces.
The MAX6316–MAX6322 are offered in a miniature 5-pin
SOT23 package.
Applications
●●
●●
●●
●●
●●
●●
Benefits and Features
●● Integrated Configuration Enables Flexible Designs
• Available in 26 Reset-Threshold Voltages
- 2.5V to 5V, in 100mV Increments
• Four Reset Timeout Periods
- 1ms, 20ms, 140ms, or 1.12s (min)
• Four Watchdog Timeout Periods
- 6.3ms, 102ms, 1.6s, or 25.6s (typ)
• Four Reset Output Stages
- Active-High, Push/Pull
- Active-Low, Push/Pull
- Active-Low, Open-Drain
- Active-Low, Bidirectional
●● Integrated Features Increase Robustness
• Guaranteed Reset Valid to VCC = 1V
• Immune to Short-Negative VCC Transients
●● Saves Board Space
• No External Components
• Small 5-Pin SOT23 Package
• AEC-Q100 Qualified
Typical Operating Circuit and Pin Configurations appears at
end of data sheet.
Portable Computers
Computers
Controllers
Intelligent Instruments
Portable/Battery-Powered Equipment
Embedded Control Systems
Ordering Information appears at end of data sheet.
Selector Guide
PART
MAX6316L
RESET OUTPUTS*
WATCHDOG
INPUT
MANUAL
RESET
INPUT
ACTIVE-LOW
PUSH/PULL
ACTIVE-HIGH
PUSH/PULL
ACTIVE-LOW
BIDIRECTIONAL
ACTIVE-LOW
OPEN-DRAIN
✔
✔
✔
—
—
—
✔
—
✔
—
—
—
✔
—
MAX6316M
✔
✔
—
MAX6317H
✔
✔
MAX6318LH
✔
—
—
✔
MAX6318MH
✔
—
—
✔
✔
MAX6319LH
—
✔
MAX6319MH
✔
—
✔
MAX6320P
—
✔
✔
—
—
—
✔
MAX6321HP
✔
—
—
✔
MAX6322HP
—
—
✔
—
✔
—
✔
—
✔
✔
✔
*The MAX6318/MAX6319/MAX6321/MAX6322 feature two types of reset output on each device.
19-0496; Rev 14; 11/18
—
✔
—
—
—
MAX6316–MAX6322
5-Pin μP Supervisory Circuits with
Watchdog and Manual Reset
Absolute Maximum Ratings
Voltage (with respect to GND)
VCC.......................................................................-0.3V to +6V
RESET (MAX6320/MAX6321/MAX6322 only).....-0.3V to +6V
All Other Pins........................................ -0.3V to (VCC + 0.3V)
Input/Output Current, All Pins..............................................20mA
Continuous Power Dissipation (TA = +70°C)
SOT23 (derate 3.9mW/°C above +70°C)..................312.6mW
Operating Temperature Range.......................... -40°C to +125°C
Junction Temperature.......................................................+150°C
Storage Temperature Range............................. -65°C to +160°C
Lead Temperature (soldering, 10s).................................. +300°C
Soldering Temperature (reflow)
Leaded Package...........................................................+240°C
Lead-Free Package......................................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Package Information
SOT23-5
PACKAGE CODE
U5+2/U5+2A
Outline Number
21-0057
Land Pattern Number
90-0174
Thermal Resistance, Single-Layer Board:
Junction to Ambient (θJA)
324.3°C/W
Junction to Case (θJC)
82°C/W
Thermal Resistance, Multi-Layer Board:
Junction to Ambient (θJA)
255.9°C/W
Junction to Case (θJC)
81°C/W
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”,
“#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing
pertains to the package regardless of RoHS status.
Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer board.
For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial.
www.maximintegrated.com
Maxim Integrated │ 2
MAX6316–MAX6322
5-Pin μP Supervisory Circuits with
Watchdog and Manual Reset
Electrical Characteristics
(VCC = 2.5V to 5.5V, TA = -40°C to +125°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
Operating Voltage Range
Supply Current
Reset Threshold Temperature
Coefficient
Reset Threshold (Note 2)
SYMBOL
VCC
ICC
CONDITIONS
TA = -40°C to +125°C
MIN
Reset Threshold Hysteresis
tRP
VCC to RESET Delay
tRD
UNITS
5.5
V
MAX6316/MAX6317/MAX
6318/MAX6320/MAX6321
10
20
VCC = 3.6V
5
12
MAX6319/MAX6322:
MR unconnected
VCC = 5.5V
3
12
VCC = 3.6V
3
8
40
TA = +25°C
TA = -40°C to +125°C
MAX63_ _ A_-T
Reset Active Timeout Period
MAX
VCC = 5.5V
DVTH/°C
VRST
TYP
1.0
VTH - 1.5%
VTH
1
1.4
VTH - 2.5%
VTH
3
ppm/°C
VTH + 1.5%
VTH + 2.5%
V
mV
2
MAX63_ _ B_-T
20
28
40
MAX63_ _ C_-T
140
200
280
MAX63_ _ D_-T
1120
1600
2240
VCC falling at 1mV/µs
µA
40
ms
µs
PUSH/PULL RESET OUTPUT (MAX6316L/MAX6317H/MAX6318_H/MAX6319_H/MAX6321HP/MAX6322HP)
RESET Output Voltage
VOL
VOH
RESET Rise Time (MAX6316L,
MAX6318LH, MAX6319LH)
tR
VOL
RESET Output Voltage
VOH
VCC ≥ 1.0V, ISINK = 50µA
0.3
VCC ≥ 2.7V, ISINK = 1.2mA
0.3
VCC ≥ 1.2V, ISINK = 100µA
0.3
VCC ≥ 4.5V, ISINK = 3.2mA
0.4
VCC ≥ 2.7V, ISOURCE = 500µA
VCC ≥ 4.5V, ISOURCE = 800µA
0.8 x VCC
VCC - 1.5
Rise time is measured from 10% to 90%
of VCC; CL = 5pF, VCC = 3.3V (Note 3)
5
VCC ≥ 2.7V, ISINK = 1.2mA
VCC ≥ 4.5V, ISINK = 3.2mA
25
ns
0.3
0.4
VCC ≥ 1.8V, ISOURCE = 150µA
0.8 x VCC
VCC ≥ 4.5V, ISOURCE = 800µA
VCC - 1.5
VCC ≥ 2.7V, ISOURCE = 500µA
V
V
0.8 x VCC
Note 1: Overtemperature limits are guaranteed by design, not production tested.
Note 2: A factory-trimmed voltage divider programs the nominal reset threshold (VTH). Factory-trimmed reset thresholds are available in 100mV increments from 2.5V to 5V (see Table 1 at end of data sheet).
Note 3: Guaranteed by design.
www.maximintegrated.com
Maxim Integrated │ 3
MAX6316–MAX6322
5-Pin μP Supervisory Circuits with
Watchdog and Manual Reset
Electrical Characteristics (continued)
(VCC = 2.5V to 5.5V, TA = -40°C to +125°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
Transitional Flip-Flop Setup Time
tS
CONDITIONS
BIDIRECTIONAL RESET OUTPUT (MAX6316M/MAX6318MH/MAX6319MH)
RESET Output Rise Time
(Note 5)
Active Pullup Enable Threshold
RESET Active Pullup Current
tR
VPTH
RESET Pullup Resistance
(Note 4)
Open-Drain Reset Output
Leakage Current
MAX
400
333
VCC = 3.0V, CL = 250pF
666
333
VCC = 5.0V, CL = 400pF
666
VCC = 5.0V
0.4
TA = -40°C to +85°C
4.2
4.7
5.2
3.6
4.7
5.8
VCC = 5.0V
UNITS
ns
VCC = 5.0V, CL = 200pF
TA = -40°C to +125°C
VOL
TYP
VCC = 3.0V, CL = 120pF
OPEN-DRAIN RESET OUTPUT (MAX6320P/MAX6321HP/MAX6322HP)
RESET Output Voltage
MIN
ns
0.65
V
20
mA
VCC > 1.0V, ISINK = 50µA
0.3
VCC > 2.7V, ISINK = 1.2mA
0.3
VCC > 1.2V, ISINK = 100µA
0.3
VCC > 4.5V, ISINK = 3.2mA
0.4
ILKG
1.0
kΩ
V
µA
WATCHDOG INPUT (MAX6316/MAX6317H/MAX6318_H/MAX6320P/MAX6321HP)
Watchdog Timeout Period
WDI Pulse Width
WDI Input Threshold
WDI Input Current
(Note 7)
tWD
tWDI
VIL
VIH
IWDI
MAX63_ _ _W-T
4.3
6.3
9.3
MAX63_ _ _X-T
71
102
153
MAX63_ _ _Y-T
1.12
1.6
2.4
MAX63_ _ _Z-T
17.9
25.6
38.4
VIL = 0.3 x VCC, VIH = 0.7 x VCC
(Note 6)
WDI = VCC, time average
VWDI = 0V, time average
50
s
ns
0.3 x VCC
120
-20
ms
0.7 x VCC
160
-15
V
µA
MANUAL RESET INPUT (MAX6316_/MAX6317H/MAX6319_H/MAX6320P/MAX6322HP)
VIL
MR Input Threshold
VIH
VIL
VIH
MR Input Pulse Width
MR Glitch Rejection
VTH > 4.0V
VTH < 4.0V
TA = -40°C to +85°C
TA = -40°C to +125°C
MR Pullup Resistance
MR to Reset Delay
Note
Note
Note
Note
4:
5:
6:
7:
0.8
2.0
0.3 x VCC
VCC = 5V
0.7 x VCC
1
µs
1.5
100
35
V
52
230
ns
75
kΩ
ns
This is the minimum time RESET must be held low by an external pulldown source to set the active pullup flip-flop.
Measured from RESET VOL to (0.8 x VCC), RLOAD = ∞.
WDI is internally serviced within the watchdog period if WDI is left unconnected.
The WDI input current is specified as the average input current when the WDI input is driven high or low. The WDI input is
designed for a three-stated-output device with a 10μA maximum leakage current and capable of driving a maximum capacitive load of 200pF. The three-state device must be able to source and sink at least 200μA when active.
www.maximintegrated.com
Maxim Integrated │ 4
MAX6316–MAX6322
5-Pin μP Supervisory Circuits with
Watchdog and Manual Reset
Typical Operating Characteristics
TA = +25°C, unless otherwise noted.)
6
VCC = 3V
4
3
2
VCC = 1V
1
0
-40
-20
0
20
40
60
80
70
60
50
40
30
20
10
0
100
-40
-20
0
20
40
60
1.02
1.01
1.00
0.99
0.98
0.97
0.96
80
40
60
80
180
80
140
100
-40
-20
0
20
40
100
1.05
1.04
1.03
1.00
0.99
0.98
0.97
0.96
0.95
-40
-20
0
20
40
60
80
74HC05
PASSIVE
4.7kΩ
PULLUP
2V/div
4.7kΩ
100pF
VRST = 4.63V
40
VRST = 2.63V
INPUT
30
74HC05
100pF
20
+5V
VCC
RESET
MR GND
10
10
100
100
MAX6316toc07
+5V
INPUT
50
100
1.01
MAX6316M/6318MH/6319MH
BIDIRECTIONAL
PULLUP CHARACTERISTICS
VRST = 3.3V
80
1.02
MAXIMUM VCC TRANSIENT DURATION
vs. RESET THRESHOLD OVERDRIVE
RESET OCCURS ABOVE LINES
60
TEMPERATURE (°C)
TEMPERATURE (°C)
60
0
MAX6316toc03
200
TEMPERATURE (°C)
70
TRANSIENT DURATION (µs)
20
NORMALIZED WATCHDOG TIMEOUT PERIOD
MAX6316toc04
1.03
MAX6316toc06
NORMALIZED RESET TIMEOUT PERIOD
1.04
0
220
MAX6316/MAX6317/MAX6318/MAX6320/MAX6321
NORMALIZED WATCHDOG TIMEOUT
PERIOD vs. TEMPERATURE
1.05
-20
240
TEMPERATURE (°C)
NORMALIZED RESET TIMEOUT
PERIOD vs. TEMPERATURE
-40
260
160
TEMPERATURE (°C)
0.95
280
MAX6316toc05
5
80
VCC = 5V
300
PROPAGATION DELAY (ns)
7
VCC FALLING AT 1mV/µs
VRST - VCC = 100mV
90
320
MAX6316toc02
VCC = 5V
8
100
RESET PROPAGATION DELAY (µs)
SUPPLY CURRENT (µA)
9
MAX6316toc01
10
MAX6316/MAX6317/MAX6319/MAX6320/MAX6322
MANUAL RESET TO RESET
PROPAGATION DELAY vs. TEMPERATURE
VCC FALLING TO RESET PROPAGATION
DELAY vs. TEMPERATURE
MAX6316/MAX6317/MAX6318/MAX6320/MAX6321
SUPPLY CURRENT vs. TEMPERATURE
1000
RESET, ACTIVE
PULLUP
2V/div
RESET
INPUT
5V/div
200ns/div
RESET THRESHOLD OVERDRIVE (mV) VRST - VCC
www.maximintegrated.com
Maxim Integrated │ 5
MAX6316–MAX6322
5-Pin μP Supervisory Circuits with
Watchdog and Manual Reset
Pin Description
PIN
MAX6316L
MAX6316M
MAX6320P
MAX6317H
MAX6318LH
MAX6318MH
MAX6321HP
MAX6319LH
MAX6319MH
MAX6322HP
NAME
FUNCTION
MAX6316L/MAX6318LH/MAX6319LH: ActiveLow, Reset Output. CMOS push/pull output
(sources and sinks current).
1
—
1
1
RESET
MAX6316M/MAX6318MH/MAX6319MH:
Bidirectional, Active-Low, Reset Output.
Intended to interface directly to microprocessors
with bidirectional resets such as the Motorola
68HC11.
MAX6320P/MAX6321HP/MAX6322HP:
Open-Drain, Active-Low, Reset Output. NMOS output (sinks current only). Connect a pullup resistor
from RESET to any supply voltage up to 6V.
—
1
3
3
RESET
2
2
2
2
GND
3
4
5
www.maximintegrated.com
3
4
5
—
4
5
4
—
5
Active-High, Reset Output. CMOS push/pull output
(sources and sinks current). Inverse of RESET.
Ground
MR
Active-Low, Manual Reset Input. Pull low to force
a reset. Reset remains asserted for the duration
of the Reset Timeout Period after MR transitions
from low to high. Leave unconnected or connected
to VCC if not used.
WDI
Watchdog Input. Triggers a reset if it remains either
high or low for the duration of the watchdog timeout
period. The internal watchdog timer clears
whenever a reset asserts or whenever WDI sees a
rising or falling edge. To disable the watchdog
fea- ture, leave WDI unconnected or three-state the
dri- ver connected to WDI.
VCC
Supply Voltage. Reset is asserted when VCC
drops below the Reset Threshold Voltage (VRST).
Reset remains asserted until VCC rises above
VRST and for the duration of the Reset Timeout
Period (tRP) once VCC rises above VRST.
Maxim Integrated │ 6
MAX6316–MAX6322
5-Pin μP Supervisory Circuits with
Watchdog and Manual Reset
VCC
MAX6316–MAX6322
RESET
(ALL EXCEPT MAX6317)
RESET
GENERATOR
RESET
(ALL EXCEPT
MAX6316/MAX6320P)
VCC
1.23V
52kΩ
MR
(ALL EXCEPT
MAX6318/MAX6321)
WDI
(ALL EXCEPT
MAX6319/MAX6322)
WATCHDOG
TRANSITION
DETECTOR
WATCHDOG
TIMER
52kΩ
GND
Figure 1. Functional Diagram
Detailed Description
A microprocessor’s (μP) reset input starts or restarts the
μP in a known state. The reset output of the MAX6316–
MAX6322 μP supervisory circuits interfaces with the
reset input of the μP, preventing code-execution errors
during power-up, power-down, and brownout conditions (see the Typical Operating Circuit). The MAX6316/
MAX6317/MAX6318/MAX6320/MAX6321 are also capable of asserting a reset should the μP become stuck in
an infinite loop.
Reset Output
The
MAX6316L/MAX6318LH/MAX6319LH
feature an active-low reset output, while the MAX6317H
MAX6318_H/MAX6319_H/MAX6321HP/MAX6322HP
feature an active-high reset output. RESET is guaranteed
to be a logic low and RESET is guaranteed to be a logic
high for VCC down to 1V.
The MAX6316–MAX6322 assert reset when VCC is
below the reset threshold (VRST), when MR is pulled
low (MAX6316_/MAX6317H/MAX6319_H/MAX6320P/
MAX6322HP only), or if the WDI pin is not serviced
www.maximintegrated.com
within the watchdog timeout period (tWD). Reset remains
asserted for the specified reset active timeout period (tRP)
after VCC rises above the reset threshold, after MR transitions low to high, or after the watchdog timer asserts the
reset (MAX6316_/MAX6317H/MAX6318_H/MAX6320P/
MAX6321HP). After the reset active timeout period (tRP)
expires, the reset output deasserts, and the watchdog
timer restarts from zero (Figure 2).
VCC
1V
VRST
VRST
1V
GND
RESET
tRP
tRD
RESET
tRP
tRD
GND
Figure 2. Reset Timing Diagram
Maxim Integrated │ 7
MAX6316–MAX6322
5-Pin μP Supervisory Circuits with
Watchdog and Manual Reset
Bidirectional RESET Output
The
MAX6316M/MAX6318MH/MAX6319MH
are
designed to interface with μPs that have bidirectional
reset pins, such as the Motorola 68HC11. Like an opendrain output, these devices allow the μP or other devices
to pull the bidirectional reset (RESET) low and assert a
reset condition. However, unlike a standard open-drain
output, it includes the commonly specified 4.7kΩ pullup
resistor with a P-channel active pullup in parallel.
This configuration allows the MAX6316M/MAX6318MH/
MAX6319MH to solve a problem associated with μPs that
have bidirectional reset pins in systems where several
devices connect to RESET (Figure 3). These μPs can
often determine if a reset was asserted by an external
device (i.e., the supervisor IC) or by the μP itself (due to
a watchdog fault, clock error, or other source), and then
jump to a vector appropriate for the source of the reset.
However, if the μP does assert reset, it does not retain the
information, but must determine the cause after the reset
has occurred.
The following procedure describes how this is done in
the Motorola 68HC11. In all cases of reset, the μP pulls
RESET low for about four external-clock cycles. It then
releases RESET, waits for two external-clock cycles, then
checks RESET’s state. If RESET is still low, the μP concludes that the source of the reset was external and, when
RESET eventually reaches the high state, it jumps to the
normal reset vector. In this case, stored-state information
is erased and processing begins from scratch. If, on the
other hand, RESET is high after a delay of two externalclock cycles, the processor knows that it caused the reset
itself and can jump to a different vector and use storedstate information to determine what caused the reset.
A problem occurs with faster μPs; two external-clock
cycles are only 500ns at 4MHz. When there are several
devices on the reset line, and only a passive pullup resistor is used, the input capacitance and stray capacitance
can prevent RESET from reaching the logic high state
(0.85 x VCC) in the time allowed. If this happens, all resets
will be interpreted as external. The μP output stage is
guaranteed to sink 1.6mA, so the rise time can not be
reduced considerably by decreasing the 4.7kΩ internal
pullup resistance. See Bidirectional Pullup Characteristics
in the Typical Operating Characteristics.
The MAX6316M/MAX6318MH/MAX6319MH overcome
this problem with an active pullup FET in parallel with the
4.7kΩ resistor (Figures 4 and 5). The pullup transistor
holds RESET high until the μP reset I/O or the supervisory circuit itself forces the line low. Once RESET goes
below VPTH, a comparator sets the transition edge flipflop, indicating that the next transition for RESET will be
low to high. When RESET is released, the 4.7kΩ resistor
pulls RESET up toward VCC. Once RESET rises above
VPTH but is below (0.85 x VCC), the active P-channel
pullup turns on. Once RESET rises above (0.85 x VCC)
or the 2μs one-shot times out, the active pullup turns
off. The parallel combination of the 4.7kΩ pullup and the
VCC
VCC
WDI*
MR**
68HC11
4.7kΩ
RESET
CIRCUITRY
RESET
RESET
RESET***
CIN
MAX6316M
MAX6318MH
MAX6319MH
* MAX6316M/MAX6318MH
** MAX6316M/MAX6319MH
*** ACTIVE-HIGH PUSH/PULL MAX6318MH/MAX6319MH
CIN
CSTRAY
RESET
CIRCUITRY
RESET
CIN
OTHER DEVICES
Figure 3. MAX6316M/MAX6318MH/MAX6319MH Supports Additional Devices on the Reset Bus
www.maximintegrated.com
Maxim Integrated │ 8
MAX6316–MAX6322
5-Pin μP Supervisory Circuits with
Watchdog and Manual Reset
VCC
MAX6316M
MAX6318MH
MAX6319MH
LASERTRIMMED
RESISTORS
VCC
VREF
52kΩ
MR
RESET
GENERATOR
WATCHDOG ON
2s ONE
SHOT
CIRCUITRY
WDI
(MAX6316M/
MAX6319MH)
(MAX6316M/
MAX6318MH)
VCC
2µs ONE SHOT
TRANSITION
FLIP-FLOP
R
Q
4.7kΩ
FF
S
RESET
ACTIVE PULLUP
ENABLE COMPARATOR
0.65V
0.85VCC
GND
Figure 4. MAX6316/MAX6318MH/MAX6319MH Bidirectional Reset Output Functional Diagram
www.maximintegrated.com
Maxim Integrated │ 9
MAX6316–MAX6322
5-Pin μP Supervisory Circuits with
Watchdog and Manual Reset
P-channel transistor on-resistance quickly charges stray
capacitance on the reset line, allowing RESET to transition from low to high within the required two electronicclock cycles, even with several devices on the reset line.
This process occurs regardless of whether the reset was
caused by VCC dipping below the reset threshold, the
watchdog timing out, MR being asserted, or the μP or
other device asserting RESET. The parts do not require
an external pullup. To minimize supply current consumption, the internal 4.7kΩ pullup resistor disconnects
from the supply whenever the MAX6316M/MAX6318MH/
MAX6319MH assert reset.
Open-Drain RESET Output
The MAX6320P/MAX6321HP/MAX6322HP have an
active-low, open-drain reset output. This output structure
will sink current when RESET is asserted. Connect a pullup resistor from RESET to any supply voltage up to 6V
(Figure 6). Select a resistor value large enough to regis-
VCC
tRP
OR
µC RESET DELAY
RESET
0.7V
0.8 x VCC
tR
tS
RESET PULLED LOW
BY µC OR
RESET GENERATOR
ACTIVE
PULLUP
TURNS ON
Figure 5. Bidirectional RESET Timing Diagram
+3.3V
MR*
+5.0V
10kΩ
RESET
5V SYSTEM
RESET***
MAX6320
MAX6321
MAX6322
GND
* MAX6320/MAX6322
** MAX6320/MAX6321
*** MAX6321/MAX6322
Figure 6. MAX6320P/MAX6321HP/MAX6322HP Open-Drain
RESET Output Allows Use with Multiple Supplies
www.maximintegrated.com
Manual-Reset Input
The MAX6316_/MAX6317H/MAX6319_H/MAX6320P/
MAX6322HP feature a manual reset input. A logic low on
MR asserts a reset. After MR transitions low to high, reset
remains asserted for the duration of the reset timeout
period (tRP). The MR input is connected to VCC through
an internal 52kΩ pullup resistor and therefore can be left
unconnected when not in use. MR can be driven with
TTL-logic levels in 5V systems, with CMOS-logic levels in
3V systems, or with open-drain or open-collector output
devices. A normally-open momentary switch from MR to
ground can also be used; it requires no external debouncing circuitry. MR is designed to reject fast, negative-going
transients (typically 100ns pulses). A 0.1μF capacitor from
MR to ground provides additional noise immunity.
The MR input pin is equipped with internal ESD-protection
circuitry that may become forward biased. Should MR
be driven by voltages higher than VCC, excessive current would be drawn, which would damage the part. For
example, assume that MR is driven by a +5V supply other
than VCC. If VCC drops lower than +4.7V, MR’s absolute
maximum rating is violated [-0.3V to (VCC + 0.3V)], and
undesirable current flows through the ESD structure from
MR to VCC. To avoid this, use the same supply for MR as
the supply monitored by VCC. This guarantees that the
voltage at MR will never exceed VCC.
Watchdog Input
VCC
WDI**
ter a logic low (see Electrical Characteristics), and small
enough to register a logic high while supplying all input
current and leakage paths connected to the RESET line.
A 10kΩ pullup is sufficient in most applications.
The MAX6316_/MAX6317H/MAX6318_H/MAX6320P/
MAX6321HP feature a watchdog circuit that monitors the
μP’s activity. If the μP does not toggle the watchdog input
(WDI) within the watchdog timeout period (tWD), reset
asserts. The internal watchdog timer is cleared by reset
or by a transition at WDI (which can detect pulses as
short as 50ns). The watchdog timer remains cleared while
reset is asserted. Once reset is released, the timer begins
counting again (Figure 7).
The WDI input is designed for a three-stated output
device with a 10μA maximum leakage current and the
capability of driving a maximum capacitive load of 200pF.
The three-state device must be able to source and sink at
least 200μA when active. Disable the watchdog function
by leaving WDI unconnected or by three-stating the driver
connected to WDI. When the watchdog timer is left open
circuited, the timer is cleared internally at intervals equal
to 7/8 of the watchdog period.
Maxim Integrated │ 10
MAX6316–MAX6322
VCC
RESET
5-Pin μP Supervisory Circuits with
Watchdog and Manual Reset
tRST
tRP
tWD
VCC
MAX6316
MAX6318
MAX6319
tRP
VCC
WDI
RESET
GND
100kΩ
MAX6316/MAX6317
MAX6318/MAX6320
MAX6321
Figure 7. Watchdog Timing Relationship
Figure 8. Ensuring RESET Valid to VCC = 0V on Active-Low
Push/Pull and Bidirectional Outputs
Applications Information
Watchdog Input Current
The WDI input is internally driven through a buffer and
series resistor from the watchdog counter. For minimum
watchdog input current (minimum overall power consumption), leave WDI low for the majority of the watchdog
timeout period. When high, WDI can draw as much as
160μA. Pulsing WDI high at a low duty cycle will reduce
the effect of the large input current. When WDI is left
unconnected, the watchdog timer is serviced within the
watchdog timeout period by a low-high-low pulse from the
counter chain.
Negative-Going VCC Transients
These supervisors are immune to short-duration, negativegoing VCC transients (glitches), which usually do not require
the entire system to shut down. Typically, 200ns largeamplitude pulses (from ground to VCC) on the supply will
not cause a reset. Lower amplitude pulses result in greater
immunity. Typically, a VCC transient that goes 100mV under
the reset threshold and lasts less than 4μs will not trigger a
reset. An optional 0.1μF bypass capacitor mounted close to
VCC provides additional transient immunity.
Ensuring Valid Reset Outputs
Down to VCC = 0V
The MAX6316_/MAX6317H/MAX6318_H/MAX6319_H/
MAX6321HP/MAX6322HP are guaranteed to operate
properly down to VCC = 1V. In applications that require
valid reset levels down to VCC = 0V, a pulldown resistor to
active-low outputs (push/pull and bidirectional only, Figure
8) and a pullup resistor to active-high outputs (push/pull
only, Figure 9) will ensure that the reset line is valid while
the reset output can no longer sink or source current. This
www.maximintegrated.com
MAX6317
MAX6318
MAX6319
MAX6321*
MAX6322*
GND
VCC
VCC
100kΩ
RESET
*THIS SCHEMATIC DOES NOT WORK ON THE OPEN-DRAIN
OUTPUTS OF THE MAX6321/MAX6322.
Figure 9. Ensuring RESET Valid to VCC = 0V on Active-High
Push/Pull Outputs
scheme does not work with the open-drain outputs of the
MAX6320/MAX6321/MAX6322. The resistor value used
is not critical, but it must be large enough not to load the
reset output when VCC is above the reset threshold. For
most applications, 100kΩ is adequate.
Watchdog Software Considerations
(MAX6316/MAX6317/MAX6318/
MAX6320/MAX6321)
One way to help the watchdog timer monitor software
execution more closely is to set and reset the watchdog
input at different points in the program, rather than pulsing the watchdog input high-low-high or low-high-low. This
technique avoids a stuck loop, in which the watchdog
timer would continue to be reset inside the loop, keeping
the watchdog from timing out.
Maxim Integrated │ 11
MAX6316–MAX6322
5-Pin μP Supervisory Circuits with
Watchdog and Manual Reset
Figure 10 shows an example of a flow diagram where the
I/O driving the watchdog input is set high at the beginning
of the program, set low at the end of every subroutine or
loop, then set high again when the program returns to the
beginning. If the program should hang in any subroutine,
the problem would be quickly corrected, since the I/O is
continually set low and the watchdog timer is allowed to
time out, causing a reset or interrupt to be issued. As
described in the Watchdog Input Current section, this
scheme results in higher time average WDI current than
does leaving WDI low for the majority of the timeout
period and periodically pulsing it low-high-low.
START
SET WDI
HIGH
PROGRAM
CODE
POSSIBLE
INFINITE LOOP PATH
SUBROUTINE OR
PROGRAM LOOP
SET WDI LOW
RETURN
Figure 10. Watchdog Flow Diagram
Pin Configurations
Typical Operating Circuit
TOP VIEW
VIN
RESET 1
GND 2
5 VCC
MAX6316
MAX6320
MR 3
RESET 1
GND 2
4 WDI
GND 2
5 VCC
MAX6318
MAX6321
RESET 3
RESET
MAX6316
4 WDI
MANUAL
RESET
MR
GND
WDI
µP
I/O
GND
SOT23
SOT23
RESET 1
RESET
MAX6317
MR 3
VCC
VCC
5 VCC
RESET 1
GND 2
4 WDI
SOT23
www.maximintegrated.com
5 VCC
MAX6319
MAX6322
RESET 3
4 MR
SOT23
Maxim Integrated │ 12
MAX6316–MAX6322
5-Pin μP Supervisory Circuits with
Watchdog and Manual Reset
Table 1. Factory-Trimmed Reset Thresholds
PART
MIN
TA = +25°C
TA = -40°C to +125°C
TYP
MAX
MIN
MAX
MAX63___50_ _-T
4.925
5.000
5.075
4.875
5.125
MAX63___49_ _-T
7.827
4.900
4.974
4.778
5.023
MAX63___48_ _-T
4.728
4.800
4.872
4.680
4.920
MAX63___47_ _-T
4.630
4.700
4.771
4.583
4.818
MAX63___46_ _-T
4.561
4.630
4.699
4.514
4.746
MAX63___45_ _-T
4.433
4.500
4.568
4.388
4.613
MAX63___44_ _-T
4.314
4.390
4.446
4.270
4.490
MAX63___43_ _-T
4.236
4.300
4.365
4.193
4.408
MAX63___42_ _-T
4.137
4.200
4.263
4.095
4.305
MAX63___41_ _-T
4.039
4.100
4.162
3.998
4.203
MAX63___40_ _-T
3.940
4.000
4.060
3.900
4.100
MAX63___39_ _-T
3.842
3.900
3.959
3.803
3.998
MAX63___38_ _-T
3.743
3.800
3.857
3.705
3.895
MAX63___37_ _-T
3.645
3.700
3.756
3.608
3.793
MAX63___36_ _-T
3.546
3.600
3.654
3.510
3.690
MAX63___35_ _-T
3.448
3.500
3.553
3.413
3.588
MAX63___34_ _-T
3.349
3.400
3.451
3.315
3.485
MAX63___33_ _-T
3.251
3.300
3.350
3.218
3.383
MAX63___32_ _-T
3.152
3.200
3.248
3.120
3.280
MAX63___31_ _-T
3.034
3.080
3.126
3.003
3.157
MAX63___30_ _-T
2.955
3.000
3.045
2.925
3.075
MAX63___29_ _-T
2.886
2.930
2.974
2.857
3.000
MAX63___28_ _-T
2.758
2.800
2.842
2.730
2.870
MAX63___27_ _-T
2.660
2.700
2.741
2.633
2.768
MAX63___26_ _-T
2.591
2.630
2.669
2.564
2.696
MAX63___25_ _-T
2.463
2.500
2.538
2.438
2.563
Table 2. Standard Versions
RESET
THRESHOLD (V)
MINIMUM
RESET
TIMEOUT (ms)
TYPICAL
WATCHDOG
TIMEOUTS (s)
MAX6316LUK29CY-T
2.93
140
1.6
ACDE
MAX6316LUK46CY-T
4.63
140
1.6
ACDD
MAX6316MUK29CY-T
2.93
140
1.6
ACDG
MAX6316MUK46CY-T
4.63
140
1.6
ACDF
MAX6317HUK46CY-T
4.63
140
1.6
ACDQ
MAX6318LHUK46CY-T
4.63
140
1.6
ACDH
MAX6318MHUK46CY-T
4.63
140
1.6
ACDJ
MAX6319LHUK46C-T
4.63
140
—
ACDK
MAX6319MHUK46C-T
4.63
140
—
ACDM
PART
www.maximintegrated.com
SOT
TOP
MARK
Maxim Integrated │ 13
MAX6316–MAX6322
5-Pin μP Supervisory Circuits with
Watchdog and Manual Reset
Table 2. Standard Versions (continued)
RESET
THRESHOLD (V)
MINIMUM
RESET
TIMEOUT (ms)
TYPICAL
WATCHDOG
TIMEOUTS (s)
SOT
TOP
MARK
MAX6320PUK29CY-T
2.93
140
1.6
ACDO
MAX6320PUK46CY-T
4.63
140
1.6
ACDN
MAX6321HPUK46CY-T
4.63
140
1.6
ACGL
MAX6322HPUK46C-T
4.63
140
1.6
ACGN
PART
Note: Thirteen standard versions are available, with a required order increment of 2500 pieces. Sample stock is generally held on
standard versions only. The required order increment for nonstandard versions is 10,000 pieces. Contact factory for availability.
Table 3. Reset/Watchdog Timeout Periods
RESET TIMEOUT PERIODS
SUFFIX
MIN
TYP
MAX
A
1
1.6
2
B
20
30
40
C
140
200
280
D
1.12
1.60
2.24
W
4.3
6.3
9.3
X
71
102
153
Y
1.12
1.6
2.4
Z
17.9
25.6
38.4
UNITS
ms
s
WATCHDOG TIMEOUT
Chip Information
ms
s
SUBSTRATE IS INTERNALLY CONNECTED TO V+
www.maximintegrated.com
Ordering Information
PART
MAX6316LUK____-T
MAX6316LUK____/V+T
MAX6316MUK____-T
MAX6317HUK____-T
MAX6318HUK____-T
MAX6318MHUK____-T
MAX6319LHUK___-T
MAX6319MHUK___-T
MAX6320PUK____-T
MAX6320PUK____/V+T
MAX6321HPUK___-T
MAX6322HPUK___-T
TEMP RANGE
-40°C to +125°C
-40°C to +125°C
-40°C to +125°C
-40°C to +125°C
-40°C to +125°C
-40°C to +125°C
-40°C to +125°C
-40°C to +125°C
-40°C to +125°C
-40°C to +125°C
-40°C to +125°C
-40°C to +125°C
PIN-PACKAGE
5 SOT23
5 SOT23
5 SOT23
5 SOT23
5 SOT23
5 SOT23
5 SOT23
5 SOT23
5 SOT23
5 SOT23
5 SOT23
5 SOT23
Devices are available in both leaded and lead(Pb)-free packaging.
Specify lead-free by replacing “-T” with “+T” when ordering.
/V Denotes an automotive-qualified part.
Note: These devices are available with factory-set VCC reset
thresholds from 2.5V to 5V, in 0.1V increments. Insert the
desired nominal reset threshold (25 to 50, from Table 1) into
the blanks following the letters UK. All devices offer factory-programmed reset timeout periods. Insert the letter corresponding
to the desired reset timeout period (A, B, C, or D from Table 3)
into the blank following the reset threshold suffix. Parts that offer
a watchdog feature (see Selector Guide) are factory-trimmed
to one of four watchdog timeout periods. Insert the letter corresponding to the desired watchdog timeout period (W, X, Y, or Z
from Table 3) into the blank following the reset timeout suffix.
Maxim Integrated │ 14
MAX6316–MAX6322
5-Pin μP Supervisory Circuits with
Watchdog and Manual Reset
Revision History
REVISION
NUMBER
REVISION
DATE
PAGES
CHANGED
0
1/98
Initial release.
1
4/98
Update to show MAX6319 as an existing part.
1, 2, 12
2
7/98
Update specifications, Selector Guide, and Table 2.
1, 12, 14
3
1/99
Include extended temperature range in EC table globals, Table 1, Ordering
Information.
4
11/99
Update available products and versions in Table 2 and Ordering Information.
1, 12, 14
5
9/02
Addition of RESET rise time specification to Electrical Characteristics table.
1, 2
6
12/05
Add lead-free option to Ordering Information.
7
11/07
Add automotive temperature to Ordering Information, Electrical Characteristics
table, Table 1, and updated Package Information.
8
8/09
Updated Ordering Information.
DESCRIPTION
—
1, 2, 3, 12, 13, 14
1, 13, 14
1, 2, 3, 12, 13, 14
13
9
6/10
Added automotive part and soldering temperatures.
10
10/11
Added automotive-qualified part ordering option for MAX6316 family
2, 13
1
11
2/13
Changed /V-T suffix to /V+T in Ordering Information
1
12
4/15
Updated the General Description and Benefits and Features sections
1
13
5/17
Added AEC-Q100 qualification
1
Corrected typo
1
Updated Package Information
2
13.1
14
11/18
For pricing, delivery, and ordering information, please visit Maxim Integrated’s online storefront at https://www.maximintegrated.com/en/storefront/storefront.html.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits)
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
© 2018 Maxim Integrated Products, Inc. │ 15