Click here to ask an associate for production status of specific part numbers.
MAX6467/MAX6468
Microprocessor Supervisory Reset Circuits
with Edge-Triggered, One-Shot Manual Reset
General Description
The MAX6467/MAX6468 microprocessor (µP) supervisory
circuits monitor single power-supply voltages from +1.8V
to +5.0V and assert a reset if the supply voltage drops
below its preset threshold. An edge-triggered, one-shot
manual reset function ensures that the µP enters the reset
mode for a fixed timeout period only, even in the event
of a continuously asserted manual reset. The MAX6467/
MAX6468 significantly improve system reliability compared
to traditional manual reset supervisory circuits.
A variety of factory-trimmed threshold options accommodate
different supply voltages and tolerances, eliminating
external components. The factory-set thresholds range
from +1.575V to +4.625V to monitor +5.0V, +3.3V, +3.0V,
+2.5V, and +1.8V supplies with various tolerances. Reset
timeout periods of 150ms (min) and 1200ms (min) are
available to accommodate different µP platforms.
A single, active-low RESET output asserts when VCC
drops below its threshold or if the edge-triggered MR
asserts low. RESET remains low for the reset timeout period after VCC rises above its threshold and for
a fixed, one-shot timeout period after a manual reset
input falling edge. RESET remains valid as long as VCC
remains above +1V. Open-drain (MAX6467) and pushpull (MAX6468) output options provide additional flexibility
in the system design.
The MAX6467/MAX6468 are offered in the space-saving
4-pin SOT143 package and the ultra-small 4-pin SC70
package and are specified over the automotive (-40°C to
+125°C) temperature range.
Features
● Precision Factory-Set Reset Threshold Voltages for
+5.0V, +3.3V, +3.0V, +2.5V, and +1.8V Supplies
● Edge-Triggered Manual Reset Input with One-Shot
Pulsed Reset Output
● Two Reset Timeout Period Options (150ms min or
1200ms min)
● Immune to Short Voltage Transients
● Low Supply Current (3µA at VCC = +1.8V)
● RESET Valid to VCC = +1V
● Active-Low Open-Drain and Push-Pull RESET
Output Options
● -40°C to +125°C Operating Temperature Range
● Small 4-Pin SC70 and SOT143 Packages
● No External Components Required
● Pin Compatible with MAX811, MAX6315, MAX6384,
and MAX6386
● AEC-Q100 Qualified, Refer to Ordering Information
for Specific /V Parts
Ordering Information appears at end of data sheet.
Typical Operating Circuit
+1.0V TO +5.5V
VCC
Applications
●
●
●
●
●
●
●
●
●
●
VCC
MAX6467
MAX6468
Cell Phones/PDAs
Embedded Control Systems
Industrial Equipment
Automotive Products
Portable/Battery-Powered Equipment
Medical Devices
DSL Modems
MP3 Players
GPS Systems
Digital Cameras
MR
RESET
GND
RESET
INPUT
µP
GND
19-2523; Rev 8; 7/21
© 2021 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
One Analog Way, Wilmington, MA 01887 U.S.A.
|
Tel: 781.329.4700
|
© 2021 Analog Devices, Inc. All rights reserved.
MAX6467/MAX6468
Microprocessor Supervisory Reset Circuits with
Edge-Triggered, One-Shot Manual Reset
Absolute Maximum Ratings
VCC to GND..........................................................-0.3V to +6.0V
RESET to GND
Open-Drain........................................................-0.3V to +6.0V
Push-Pull............................................... -0.3V to (VCC + 0.3V)
MR to GND................................................ -0.3V to (VCC + 0.3V)
Input/Output Current (all pins).............................................20mA
Continuous Power Dissipation (TA = +70°C)
4-Pin SC70 (derate 3.1mW/°C above +70°C)..............245mW
4-Pin SOT143 (derate 4mW/°C above +70vC)............320mW
Operating Temperature Range.......................... -40°C to +125°C
Storage Temperature Range............................. -65°C to +150°C
Junction Temperature.......................................................+150°C
Lead Temperature (soldering, 10s).................................. +300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics
(VCC = +1.2V to +5.5V, TA = -40°C to +125°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
Operating Voltage Range
Supply Current
SYMBOL
VCC
ICC
CONDITIONS
MIN
VTH
VCC Reset Delay
tRD
VCC Reset Timeout Period
tRP
MAX
TA = 0°C to +125°C
1.0
5.5
TA = -40°C to 0°C
1.2
5.5
VCC = +5.5V, no load
7
13
VCC = +3.6V, no load
6
11
VCC = +2.5V, no load
4
8
VCC = +1.8V, no load
VCC Reset Threshold
(See the Reset Threshold Table)
TYP
3
7.5
VTH
+1.5%
TA = +25°C
-1.5%
TA = -40°C to +85°C
-2.5%
+2.5%
-3%
+3%
TA = +85°C to +125°C
VCC falling at 10mV/µs from VTH + 100mV
to VTH - 100mV
35
UNITS
V
µA
V
µs
D3 option
150
225
300
D7 option
1200
1800
2400
ms
MR Timeout Period
tMRP
D3 and D7 options
150
225
300
ms
MR Rising Debounce Period
(Note 2)
tDEB
D3 and D7 options
150
225
300
ms
VIL
MR Input Voltage
VIH
VIL
VIH
VTH < +4V
VTH ≥ +4V
MR Minimum Input Pulse
0.3 x VCC
0.7 x VCC
0.8
V
2.4
1
µs
MR Glitch Rejection
100
ns
MR to RESET Delay
200
ns
MR Pullup Resistance
RESET Output High
(MAX6468 Only)
www.analog.com
MR to VCC
VOH
500
VCC ≥ +2.5V, ISOURCE = 500µA, RESET
not asserted
0.8 x VCC
VCC ≥ +4.5V, ISOURCE = 800µA, RESET
not asserted
0.8 x VCC
1560
3000
Ω
V
Analog Devices │ 2
MAX6467/MAX6468
Microprocessor Supervisory Reset Circuits with
Edge-Triggered, One-Shot Manual Reset
Electrical Characteristics
(VCC = +1.2V to +5.5V, TA = -40°C to +125°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
RESET Output Low
CONDITIONS
VOL
RESET Output Leakage Current
(MAX6467 Only)
ILKG
MIN
TYP
MAX
VCC ≥ +1V, ISINK = 80µA, RESET asserted
0.3
VCC ≥ +2.5V, ISINK = 1.2mA, RESET
asserted
0.3
VCC ≥ +4.5V, ISINK = 3.2mA, RESET
asserted
0.3
RESET not asserted
UNITS
V
1
µA
Note 1: Specifications over temperature are guaranteed by design. Production testing at TA = +25°C only.
Note 2: The MR input ignores falling edges that occur within the MR rising debounce period (tDEB) after MR first rises from low to
high (after a valid MR reset assertion). This prevents invalid reset assertion due to switch bounce.
Typical Operating Characteristics
(VCC = +5V, MAX6468US29D3 device, TA = +25°C, unless otherwise noted.)
6
5
4
3
VCC = +2.5V
4
3
MAX6467 toc03
VCC = VTH + 100mV TO VTH - 100mV
24
22
20
18
16
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
-40 -25 -10 5 20 35 50 65 80 95 110 125
SUPPLY VOLTAGE (V)
TEMPERATURE (°C)
RESET TIMEOUT PERIOD
vs. TEMPERATURE
NORMALIZED RESET THRESHOLD
vs. TEMPERATURE
OUTPUT VOLTAGE LOW
vs. SINK CURRENT
208
207
206
205
204
203
202
201
-40 -25 -10 5 20 35 50 65 80 95 110 125
TEMPERATURE (°C)
www.analog.com
1.010
600
550
500
450
1.005
1.000
0.995
0.990
-40 -25 -10 5 20 35 50 65 80 95 110 125
TEMPERATURE (°C)
MAX6467 toc06
TEMPERATURE (°C)
NORMALIZED RESET THRESHOLD (V)
RESET TIMEOUT PERIOD (ms)
5
0
-40 -25 -10 5 20 35 50 65 80 95 110 125
209
200
6
VCC TO RESET DELAY
vs. TEMPERATURE
1
MAX6467 toc04
210
7
2
VCC = +1.8V
1
0
8
26
VOL (mV)
2
9
VCC TO RESET DELAY (µs)
7
MAX6467 toc02
VCC = +3.6V
SUPPLY CURRENT vs. SUPPLY VOLTAGE
MAX6467 toc05
8
VCC = +5.5V
10
SUPPLY CURRENT (µA)
SUPPLY CURRENT (µA)
9
MAX6467 toc01
10
SUPPLY CURRENT vs. TEMPERATURE
VCC = 5.0V
400
350
300
250
200
150
100
50
0
0
1
2
3
4
5
6
7
8
9
10
ISINK (mA)
Analog Devices │ 3
MAX6467/MAX6468
Microprocessor Supervisory Reset Circuits with
Edge-Triggered, One-Shot Manual Reset
Typical Operating Characteristics
(VCC = +5V, MAX6468US29D3 device, TA = +25°C, unless otherwise noted.)
4.5
4.0
VOH (V)
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
0
1
2
3
4
5
6
7
400
300
200
RESET ASSERTS
ABOVE THIS LINE
100
0
10
20
30
MR TO RESET DELAY
vs. TEMPERATURE
40
50
60
PROPAGATION DELAY
(WITH 100mV OVERDRIVE)
MAX6467 toc10
MAX6467 toc09
MR TO RESET DELAY (ns)
500
RESET THRESHOLD OVERDRIVE (mV)
ISOURCE (mA)
120
600
0
8
MAXIMUM TRANSIENT DURATION
vs. RESET THRESHOLD OVERDRIVE
MAX6467 toc08
VCC = +5.0V
5.0
MAXIMUM TRANSIENT DURATION (µs)
5.5
MAX6467 toc07
OUTPUT VOLTAGE HIGH
vs. SOURCE CURRENT
115
110
3.0V
VCC 100mV/div
AC-COUPLED
105
100
95
2.8V
90
3V
85
80
75
70
65
60
RESET 1V/div
0
-40 -25 -10 5 20 35 50 65 80 95 110 125
TEMPERATURE (°C)
RESET PULLUP AND PULLDOWN RESPONSE
MAX6467 toc11
CRESET = 47pF, RPULLUP = 100kΩ,
VPULLUP = 1.6V
4µs/div
RESET TIMEOUT PERIOD
MAX6467 toc12
3.3V
1.675V
VCC 200mV/div
1.475V
VCC 2V/div
0
1.6V
3.3V
RESET 500mV/div
MAX6467_S16D3-T
40µs/div
www.analog.com
RESET 2V/div
0
0
40ms/div
Analog Devices │ 4
MAX6467/MAX6468
Microprocessor Supervisory Reset Circuits with
Edge-Triggered, One-Shot Manual Reset
Pin Configurations
TOP VIEW
GND 1
RESET 2
MAX6467XS
MAX6468XS
4
VCC
GND 1
3
MR
RESET 2
MAX6467US
MAX6468US
4
VCC
3
MR
SOT143
SC70
Pin Description
PIN
NAME
1
GND
FUNCTION
Ground
Reset Output. RESET is an active-low open-drain (MAX6467) or push-pull (MAX6468) output. RESET
asserts low when VCC drops below the selected threshold and remains low for the VCC reset timeout period
after VCC rises above the threshold. The RESET one-shot asserts low for a fixed MR reset timeout period on
the falling edge of the manual reset input. The open-drain output requires an external pullup resistor.
2
RESET
3
MR
Manual Reset Input. Drive MR low to initiate a reset output. MR controls an edge-triggered one-shot that
asserts RESET low for a fixed MR timeout period when MR is driven low. Internal timing circuitry ignores
switch close and open bounce to ensure proper one-shot reset timing.
4
VCC
Power-Supply Input. VCC provides power to the device and is also a monitored voltage. When VCC drops
below the selected threshold, RESET asserts low and remains low for the reset timeout period after VCC
rises above the threshold. For better noise immunity, bypass VCC to GND with a 0.1µF capacitor.
www.analog.com
Analog Devices │ 5
MAX6467/MAX6468
Microprocessor Supervisory Reset Circuits with
Edge-Triggered, One-Shot Manual Reset
VCC
VTH
GND
SWITCH
BOUNCE
MR
SWITCH
BOUNCE
SWITCH
BOUNCE
GND
RESET
tRP
tMRP
tDEB
tMRP
GND
Figure 1. Timing Diagram
Detailed Description
Reset Output
The MAX6467 provides an active-low open-drain
RESET output. The MAX6468 provides an active-low
push-pull RESET output. RESET asserts low if VCC
drops below the selected threshold or if a falling edge
occurs on MR. RESET remains low for the VCC reset
timeout period after VCC increases above the threshold
voltage or is one-shot pulsed low for the MR timeout
period after a falling edge on MR.
Manual Reset Input
Many µP-based products require manual reset capability,
allowing the operator, a test technician, or external logic
circuitry to initiate a reset. A falling edge on MR asserts
www.analog.com
RESET low. RESET is one-shot pulsed low for the MR
timeout period after a falling edge on MR. An internal
1.5kΩ pullup resistor to VCC allows MR to be left unconnected if not used. MR can be driven with TTL or CMOSlogic levels, or with open-drain/collector outputs. Connect
a normally open momentary pushbutton switch from
MR to GND to realize a manual reset function. External
debounce circuitry is not required, as the MAX6467/
MAX6468 respond to the first falling edge on MR and
ignore subsequent falling edges within the reset timeout
period and during the MR debounce period (see Figure
1). After MR goes high for 150ms (tDEB), the manual reset
one-shot is ready to trigger a reset on the next MR falling
edge. Connect a 0.1µF capacitor from MR to GND when
using long cables to provide additional noise immunity.
Analog Devices │ 6
MAX6467/MAX6468
Microprocessor Supervisory Reset Circuits with
Edge-Triggered, One-Shot Manual Reset
Reset Timeout Delay*
RESET TIMEOUT SUFFIX
VCC RESET TIMEOUT PERIOD
(min/max) (ms)
MR TIMEOUT PERIOD
(min/max) (ms)
MR RISING DEBOUNCE PERIOD
(min/max) (ms)
D3
150/300
150/300
150/300
D7
1200/2400
150/300
150/300
*Additional reset timeout options may be available. Contact factory for availability.
Applications Information
Falling VCC Transients
In addition to issuing a reset to the µP during power-up,
power-down, and brownout conditions, the MAX6467/
MAX6468 are relatively immune to short-duration falling VCC transients (glitches). The Typical Operating
Characteristics section shows the Maximum Transient
Duration vs. VCC Overdrive for which the MAX6467/
MAX6468 do not generate a reset pulse. This graph was
generated using a falling pulse applied to VCC starting
above the actual reset threshold and ending below the
threshold by the magnitude indicated (VCC Overdrive).
The graph indicates the typical maximum pulse width a
falling VCC transient can have without initiating a reset
pulse. As the magnitude of the transient increases (goes
farther below the reset threshold), the maximum allowable
pulse width decreases. A 0.1µF bypass capacitor from
VCC to GND provides additional transient immunity.
Ensuring a Valid RESET Output Down
to VCC = 0V
The MAX6467/MAX6468 guarantee proper operation
down to VCC = +1V. In applications that require valid
reset levels down to VCC = 0V, a pulldown resistor to
active-low outputs (MAX6468 only, Figure 3) ensures
that RESET remains valid while the RESET output can
no longer sink current. This scheme does not work with
the open-drain outputs of the MAX6467. Ensure that the
resistor value used does not overload the RESET output
when VCC is above the reset threshold. For most applications, use 100kΩ to 1MΩ.
VCC
MAX6467
MAX6468
1.5kΩ
VCC
MR
VCC
MR ONE-SHOT/
DEBOUNCE
MAX6468
RESET
R1
100kΩ
VCC
RESET
TIMEOUT
PERIOD
RESET
OUTPUT
RESET
GND
1.23V
GND
Figure 2. Functional Diagram
Figure 3. RESET Valid to VCC = 0V
Chip Information
TRANSISTOR COUNT: 748
PROCESS: BiCMOS
www.analog.com
Analog Devices │ 7
MAX6467/MAX6468
Microprocessor Supervisory Reset Circuits with
Edge-Triggered, One-Shot Manual Reset
Standard Versions
Reset Threshold (-40°C to +85°C)
PART
TOP MARK
MAX6467XS16D3
AGL
MAX6467XS22D3
AGM
MAX6467XS26D3
AGN
MAX6467XS29D3
AGO
MAX6467XS46D3
AGP
MAX6467US16D3
KAFN
MAX6467US22D3
KAFO
MAX6467US26D3
KAFP
MAX6467US29D3
KAFQ
MAX6467US46D3
KAFR
MAX6468XS16D3
AGQ
MAX6468XS22D3
AGR
MAX6468XS26D3
AGS
MAX6468XS29D3
AGC
MAX6468XS46D3
AGB
MAX6468US16D3
KAFS
MAX6468US22D3
KAFT
MAX6468US26D3
KAFU
MAX6468US29D3
KAEW
MAX6468US46D3
KAFV
www.analog.com
SUFFIX
VTH (min)
VTH (typ)
VTH (max)
46
4.509
4.625
4.741
45
4.388
4.500
4.613
44
4.266
4.375
4.484
43
4.193
4.300
4.408
42
4.095
4.200
4.305
41
3.998
4.100
4.203
40
3.900
4.000
4.100
39
3.803
3.900
3.998
38
3.705
3.800
3.895
37
3.608
3.700
3.793
36
3.510
3.600
3.690
35
3.413
3.500
3.588
34
3.315
3.400
3.485
33
3.218
3.300
3.383
32
3.120
3.200
3.280
31
2.998
3.075
3.152
30
2.925
3.000
3.075
29
2.852
2.925
2.998
28
2.730
2.800
2.870
27
2.633
2.700
2.768
26
2.559
2.625
2.691
25
2.438
2.500
2.563
24
2.340
2.400
2.460
23
2.255
2.313
2.370
22
2.133
2.188
2.242
21
2.048
2.100
2.153
20
1.950
2.000
2.050
19
1.853
1.900
1.948
18
1.755
1.800
1.845
17
1.623
1.665
1.707
16
1.536
1.575
1.614
Analog Devices │ 8
MAX6467/MAX6468
Microprocessor Supervisory Reset Circuits with
Edge-Triggered, One-Shot Manual Reset
Ordering Information
PART
TEMP RANGE
Package Information
PINPACKAGE
MAX6467XS_ _D_-T
-40°C to +125°C
4 SC70-4
MAX6467XS_ _D_/V+T*
-40°C to +125°C
4 SC70-4
MAX6467XS29D3/V+T
-40°C to +125°C
4 SC70-4
MAX6467XS32D3/V+T
-40°C to +125°C
MAX6467XS16D3/V+T
For the latest package outline information and land patterns
(footprints), go to www.maximintegrated.com/packages. Note
that a “+”, “#”, or “-” in the package code indicates RoHS status
only. Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
4 SC70-4
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
-40°C to +125°C
4 SC70-4
4 SC70
X4+1
21-0098
LAND
PATTERN
NO.
90-0187
MAX6467US_ _D_-T
-40°C to +125°C
4 SOT143-4
4 SOT143
U4+1
21-0052
90-0183
MAX6468XS_ _D_-T
-40°C to +125°C
4 SC70-4
MAX6468US_ _D_-T
-40°C to +125°C
4 SOT143-4
Note: Insert reset threshold suffix (see Reset Threshold table)
after XS or US. Insert reset timeout delay (see Reset Timeout
Delay table) after D to complete the part number. Sample stock
is generally held on standard versions only (see Standard
Versions table). Standard versions have an order increment
requirement of 2500 pieces. Nonstandard versions have an
order increment requirement of 10,000 pieces. Contact factory
for availability. Devices are available in both leaded and leadfree packaging. Specify lead-free by replacing “T” with “+T”
when ordering.
T = Tape and reel.
/V denotes an automotive qualified part.
+Denotes a lead(Pb)-free/RoHS-compliant package.
*Future product—contact factory for availability.
www.analog.com
Analog Devices │ 9
MAX6467/MAX6468
Microprocessor Supervisory Reset Circuits with
Edge-Triggered, One-Shot Manual Reset
Revision History
REVISION
NUMBER
REVISION
DATE
2
3/14
Added /V OPNs
1
4/14
Removed automotive reference from Applications section
1
6/14
Reversed 4/14 change and added automotive reference back to Applications
section
1
4
10/14
Fixed typo in Package Information section
9
5
10/15
Fixed MR Pullup Resistance specification in Electrical Characteristics table
6
3/18
Updated Benefits and Features and Ordering Information table
3
6.1
DESCRIPTION
Reformatted Standard Versions table
7
3/20
Updated Features, Absolute Maximum Ratings, Detailed Description,
Applications Information, and Package Information table
8
7/21
Updated Ordering information table
PAGES
CHANGED
2
1, 9
8
1, 2, 6, 7, 9
9
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is
assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that
may result from its use.Specifications subject to change without notice. No license is granted by implicationor
otherwise under any patent or patent rights of Analog Devices. Trademarks andregistered trademarks are the
property of their respective owners.
w w w . a n a l o g . c o m
Analog Devices │ 10
工商网监
湘ICP备2023018690号
