MAX706MJA/883B

SCOPE: MICROPROCESSOR SUPERVISORY CIRCUITS Device Type 01 02 03 04 05 Generic Number MAX705(x)/883B MAX706(x)/883B MAX707(x)/883B MAX708(x)/883B MAX813L(x)/883B Case Outline(s). The case outlines shall be designated in Mil-Std-1835 and as follows: Case Outline Package Code Outline Letter Mil-Std-1835 MAXIM SMD JA P GDIP1-T08 or CDIP2-T08 8 LEAD CERDIP J08 LP 2 CQCC1-N20 20 Pin Leadless Chip L20 Absolute Maximum Ratings Terminal Voltage (with respect to GND) VCC .................................................................................................................. -0.3V to +6.0V All other Inputs 1/ .................................................................................. -0.3V to (Vcc+0.3V) Input Current VCC ................................................................................................................................. 10mA GND ............................................................................................................................... 10mA Output Current (all outputs) ............................................................................................... 10mA Lead Temperature (soldering, 10 seconds) ...................................................................... +300°C Storage Temperature ......................................................................................... -65°C to +160°C Continuous Power Dissipation ................................................................................... TA=+70°C 8 lead CERDIP(derate 8.0mW/°C above +70°C) ...................................................... 640mW 20 lead LCC(derate 9.1mW/°C above +70°C) .......................................................... 727mW Junction Temperature TJ ............................................................................................. +150°C Thermal Resistance, Junction to Case, ΘJC: Case Outline 8 lead CERDIP........................................................................ 55°C/W Case Outline 20 leadless Chip carrier .......................................................... 20°C/W Thermal Resistance, Junction to Ambient, ΘJA: Case Outline 8 lead CERDIP...................................................................... 125°C/W Case Outline 20 leadless Chip carrier ........................................................ 110°C/W Recommended Operating Conditions Ambient Operating Range (TA) ............................................................... -55°C to +125°C Supply Voltage Range (VCC) ...................................................................... +1.2V to +5.5V ___ NOTE 1: The input voltage limits on PFI and MR may be exceeded if the input current is less than 10mA. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ---------------------------- Electrical Characteristics of MAX705/706/707/708/813L/883B for /883B and SMD 5962-93267 19-0216 Page 2 of Rev. C 7 TABLE 1. ELECTRICAL TESTS: TEST Symbol CONDITIONS -55 °C ≤TA≤+125°C 2/ Unless otherwise specified Operating Voltage VCC Range Supply Current I RESET AND WATCHDOG TIMER Reset Threshold VRT Group A Subgroup Device type 1,2,3 All 1,2,3 All Limits Min 3/ 1.2 Limits Max 3/ 5.5 500 01,03,05 4.5 4.75 4.25 VCC-1.5 4.5 1,2,3 ISOURCE=800µA VRSTL ISINK-3.2mA 1,2,3 µA 01,02, 03,04 0.4 V 0.3 ISINK=100µA, VCC=1.2V ISOURCE=800µA RESET Output Voltage V V 02,04 ______ RESET Ouput Voltage Units 03,04,05 VCC-1.5 VRSTH ISINK=1.2mA 1,2,3 03,04 0.4 V 0.4 0.8 V 0.9 ISOURCE=4µA, VCC=1.2V 05 WDI Input Threshold Logic Low WDI Input Threshold Logic High WDI Input Current WDVIL ISINK=3.2mA VCC=5V 1,2,3 01,02,05 WDIVIH VCC=5V 1,2,3 01,02,05 WDIIN WDI=VCC 1,2,3 01,02,05 3.5 150 µA WDI=0V ____ WDO Output Voltage ____ WDO V -150 VCC-1.5 ISOURCE=800µA VOH 1,2,3 ____ WDO V 01,02,05 0.4 ISINK=1.2mA VOL Reset Pulse Width Watchdog Timeout Period WDI Pulse Width MANUAL RESET ___ MR Pull-up Current ___ MR Input Threshold Logic Low ___ MR Input Threshold Logic High tRS tWD 9,10,11 9,10,11 All 01,02,05 140 1.0 9,10,11 01,02,05 50 1,2,3 All 100 ___ MRVIL 1,2,3 All ___ MRVIH 1,2,3 All tWP VIL=0.4V, VIH=(VCC)(0.8)V ___ MRIPU ___ MR=0V ---------------------------- Electrical Characteristics of MAX705/706/707/708/813L/883B for /883B and SMD 5962-93267 280 2.25 ms s ns 600 µA 0.8 V 2.0 V 19-0216 Page 3 of Rev. C 7 TEST Symbol ___ MR to Reset Out tMD Delay ___ MR Pulse Width tMR POWER-FAIL DETECTOR PFI Input PFIVTH Threshold PFI Input Current PFIIN ___ ___ PFOVO PFO Output Voltage CONDITIONS 2/ -55 °C ≤TA≤+125°C Unless otherwise specified NOTE 4 VCC=5V Group A Subgroup Device type Limits Min 3/ Limits Max 3/ Units 9,10,11 All 9,10,11 All 150 1,2,3 All 1.2 1.3 V 1,2,3 All -25 VCC-1.5 +25 nA 1,2,3 All ISOURCE=800µA 250 ns ns V 0.4 ISINK=3.2mA NOTE 2: For device types 01, 03, and 05, VCC=4.75V to 5.5V unless otherwise specified and for device 02, 04, VCC=4.5V to 5.5V unless otherwise specified. NOTE 3: The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum is used for these limits. Negative current shall be defined as conventional current flow out of a device terminal. ______ NOTE 4: Applies to both RESET in device types 03-05 and RESET in device types 01 and 04. 01 01 02 02 03 03 04 04 05 05 Package 8 pin CERDIP 20 pin LCC 8 pin CERDIP 20 pin LCC 8 pin CERDIP 20 pin LCC 8 pin CERDIP 20 pin LCC 8 pin CERDIP 20 pin LCC ---------------------------- ORDERING INFORMATION: MAX705MJA/883B MAX705MLP/883B MAX706MJA/883B MAX706MLP/883B MAX707MJA/883B MAX707MLP/883B MAX708MJA/883B MAX708MLP/883B MAX813LMJA/883B MAX813LMLP/883B SMD NUMBER 5962-9326701MPA 5962-9326701M2C 5962-9326702MPA 5962-9326702M2C 5962-9326703MPA 5962-9326703M2C 5962-9326704MPA 5962-9326704M2C 5962-9326705MPA 5962-9326705M2C Electrical Characteristics of MAX705/706/707/708/813L/883B for /883B and SMD 5962-93267 19-0216 Page 4 of Rev. C 7 TERMINAL CONNECTIONS: MAX705/706 MAX705/706 J8 L20 1 ___ NC MR 2 VCC ___ MR 3 GND NC 4 PFI NC 5 ____ VCC PFO 6 WDI NC 7 ______ GND RESET 8 _____ NC WDO 9 NC 10 PFI 11 NC 12 ____ PFO 13 NC 14 NC 15 WDI 16 NC 17 ____ RST 18 NC 19 NC 20 ____ WDO ---------------------------- MAX707/708 J8 ___ MR VCC GND PFI ____ PFO NC ______ RESET RESET MAX707/708 L20 NC ___ MR NC NC VCC NC GND NC MAX813L J8 ___ MR VCC GND PFI ____ PFO WDI RESET _____ WDO NC PFI NC ____ PFO NC NC NC NC ____ RST NC NC RST Electrical Characteristics of MAX705/706/707/708/813L/883B for /883B and SMD 5962-93267 MAX813L L20 NC ___ MR NC NC VCC NC GND NC NC PFI NC ____ PFO NC NC WDI NC RST NC NC ____ WDO 19-0216 Page 5 of Rev. C 7 QUALITY ASSURANCE Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in MilStd-883. Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015: 1. Test Condition, A, B, C, or D. 2. TA = +125°C minimum. 3. Interim and final electrical test requirements shall be specified in Table 2. Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B, C, and D inspection. Group A inspection: 1. Tests as specified in Table 2. 2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted. Group C and D inspections: a. End-point electrical parameters shall be specified in Table 1. b. Steady-state life test, Method 1005 of Mil-Std-883: 1. Test condition A, B, C, D. 2. TA = +125°C, minimum. 3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883. TABLE 2. ELECTRICAL TEST REQUIREMENTS Mil-Std-883 Test Requirements Interim Electric Parameters Method 5004 Final Electrical Parameters Method 5005 Group A Test Requirements Method 5005 Group C and D End-Point Electrical Parameters Method 5005 * Subgroups per Method 5005, Table 1 1 1*, 2, 3, 9, 10, 11 1, 2, 3, 9, 10, 11 1, 9 PDA applies to Subgroup 1 only. ---------------------------- Electrical Characteristics of MAX705/706/707/708/813L/883B for /883B and SMD 5962-93267 19-0216 Page 6 of Rev. C 7