MAX78630+PPM Evaluation Kit
User Manual
July 2013
Rev. 0
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent
licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000
© 2013 Maxim Integrated Products, Inc.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
MAX78630+PPM Evaluation Kit User Manual
Table of Contents
1
Introduction ......................................................................................................................................... 4
1.1
Ordering Information .................................................................................................................. 4
1.2
Package Contents...................................................................................................................... 4
1.3
System Requirements ............................................................................................................... 4
1.4
Safety and ESD Notes ............................................................................................................... 6
1.5
Testing the MAX78630+PPM EV Board Prior to Shipping ........................................................ 6
2
Installation ........................................................................................................................................... 7
2.1
USB Driver Installation ............................................................................................................... 7
2.1.1 Confirm COM Port Mapping ............................................................................................. 7
2.1.2 FTDI COM Port Trouble Shooting.................................................................................... 7
2.2
Powering the EV Kit Board ........................................................................................................ 8
2.3
Basic Connection Setup ............................................................................................................ 8
2.3.1 Wye-Connected or 3V Delta-Connected Three-Phase Systems..................................... 8
2.3.2 2V Delta-Connected Three-Phase Systems .................................................................. 10
2.3.3 Neutral Current Measurement Considerations .............................................................. 12
2.4
Analog Input Jumper Descriptions ........................................................................................... 13
3
Serial Interfaces Selection and Configuration ............................................................................... 14
3.1
UART Interface Settings .......................................................................................................... 14
3.2
SPI Settings ............................................................................................................................. 15
4
Graphical User Interface (GUI) ......................................................................................................... 17
4.1
GUI Initialization ....................................................................................................................... 17
4.1.1 SSI ID Tab ...................................................................................................................... 17
4.1.2 Device Tab ..................................................................................................................... 18
4.1.3 Scaling Tab .................................................................................................................... 18
4.1.4 Direct Tab....................................................................................................................... 19
4.1.5 Command and Configuration Tab .................................................................................. 20
4.1.6 Calibration Tab ............................................................................................................... 21
4.1.7 Power Tab ...................................................................................................................... 21
4.1.8 Energy Tab..................................................................................................................... 22
4.1.9 Fundamental Tab ........................................................................................................... 22
4.1.10 Min/Max Tab ................................................................................................................. 23
4.1.11 Alarm Tab ..................................................................................................................... 24
4.1.12 Monitor Tab ................................................................................................................... 25
5
Schematics, Bill of Materials, and PCB Layouts............................................................................ 26
5.1
MAX78630+PPM EV Board Schematics ................................................................................. 26
5.2
MAX78630+PPM EV Board Bill of Materials ........................................................................... 28
5.3
MAX78630+PPM EV Board PCB Layouts............................................................................... 30
6
Contact Information .......................................................................................................................... 32
Revision History ........................................................................................................................................ 32
2
Rev 0
MAX78630+PPM Evaluation Kit User Manual
Figures
Figure 1: MAX78630+PPM EV Kit Typical Application Diagram........................................................................... 5
Figure 2: MAX78630+PPM EV Board Connections .............................................................................................. 8
Figure 3: MAX78630+PPM EV Board Connections ............................................................................................ 10
Figure 4: MAX78630+PPM EV Board Connections ............................................................................................ 12
Figure 5: MAX78630+PPM EV Board Electrical Schematic (1 of 2) ................................................................... 26
Figure 6: MAX78630+PPM EV Board Electrical Schematic (2 of 2) ................................................................... 27
Figure 7: MAX78630+PPM EV Board PCB Top View ........................................................................................ 30
Figure 8: MAX78630+PPM EV Board PCB Bottom View ................................................................................... 31
Table
Table 1: J15 Jumper Description......................................................................................................................... 13
Table 2: J11 Jumper Description......................................................................................................................... 13
Table 3: J13 Jumper Description......................................................................................................................... 13
Table 4: J19 Jumper Description......................................................................................................................... 13
Table 5: J42 Jumper Description......................................................................................................................... 13
Table 6: J14 Jumper Description......................................................................................................................... 13
Table 7: J20 Jumper Description......................................................................................................................... 13
Table 8: J43 Jumper Description......................................................................................................................... 13
Table 9: SW4 Serial Interface Selection ............................................................................................................. 14
Table 10: SW5 Address Selection ...................................................................................................................... 14
Table 11: Jumper Setting for UART/USB Interface............................................................................................. 14
Table 12: Jumpers Settings for UART/RS-485/422 ............................................................................................ 15
Table 13: J22 RS-485/422 Connector Pin Assignment ...................................................................................... 15
Table 14: Jumper Setting for SPI/USB Interface................................................................................................. 15
Table 15: Jumper Settings for Connecting on J16 .............................................................................................. 16
Table 16: J16 Connector Pin Assignment ........................................................................................................... 16
Table 17: MAX78630+PPM EV Board Bill of Materials....................................................................................... 28
Rev 0
3
MAX78630+PPM Evaluation Kit User Manual
1 Introduction
The MAX78630+PPM Evaluation Kit (EV kit) demonstrates the capability of the MAX78630+PPM for
monitoring a three-phase AC load using up to three voltages and three currents (sensors included). The EV kit
connects to a PC through a USB cable that provides both power and data communication to the board. A
Windows®-based graphical user interface (GUI) communicates with the device over a virtual for simplified
access to measurement data and controls.
1.1 Ordering Information
PART
MAX78630+PPMEVK1#
TYPE
EV Kit
#Denotes a RoHS-compliant device that may include lead that is
exempt under the RoHS requirements.
1.2 Package Contents
The MAX78630+PPM EV kit includes the following:
•
•
•
•
•
MAX78630+PPM EV Board
Three 50A Current Transformers (CR Magnetics CR-8449-2500-N)
USB Cable Assembly USB A-B 28/24 1.8M (Tyco/Amp 1487588-3)
CD with Documentation, GUI Application, and USB Drivers
Calibration Coefficients Document (Hardcopy Only)
1.3 System Requirements
In addition to an AC source and load for measuring, the MAX78630+PPM EV kit requires use of a PC with the
following features:
•
•
1GHz processor and 1GB RAM
Minimum 1024 x 768 video display resolution
•
•
Available USB port
Microsoft Windows 7 or Windows XP®
Windows and Windows XP are registered trademarks of Microsoft Corp.
4
Rev 0
MAX78630+PPM Evaluation Kit User Manual
Line 3
Line 1
Neutral
Line 2
Three Phase
AC Source
Host PC
MAX78630+PPM Eval Board
J4
5V
Shunt
Isolation
3V3 Reg.
USB
USB
Controller
RS485
UART
Isolation
J5
Burden
Resistor
J
3
9
Burden
Resistor
J
4
0
Burden
Resistor
J
4
1
CT1
CT2
CT3
MAX78630
+PPM
16 DIOs
Voltage
Divider
J1
Voltage
Divider
J2
Voltage
Divider
J3
Note:
Jumpers
not shown
Three-phase
Load Under Test
Figure 1: MAX78630+PPM EV Kit Typical Application Diagram
Rev 0
5
MAX78630+PPM Evaluation Kit User Manual
1.4 Safety and ESD Notes
EXERCISE CAUTION WHEN LIVE AC VOLTAGES ARE PRESENT!
Do not connect test equipment, ICE emulators or external development boards
directly to the MAX78630+PPM hardware. Damage to the MAX78630+PPM and
external equipment will occur due to the MAX78630+PPM’s “high side” reference
topology. The MAX78630+PPM’s V3P3 (i.e., “high side”) is connected directly to
Neutral (Earth Ground) or Line Voltage, creating a ground reference disparity with
any properly grounded external equipment.
The board components and firmware settings are designed to operate with the following nominal AC electrical
ranges:
Voltage
Current
Line Frequency
10-400V AC
10mA – 50A
46-64Hz
The maximum current is determined by the current transformer (CT) that is provided with this EV kit:
CR Magnetics model no. CR8449-2500-N.
1.5 Testing the MAX78630+PPM EV Board Prior to Shipping
Before every EV kit is shipped, the board (and sensors) undergoes a single-load point calibration using precise
energy source equipment. The device temperature is also calibrated at the same time. Results printed out on
paper and included with the EV kit.
Note that the board is calibrated using the marked CTs included with the kit. Therefore, CT1 should be
connected to I1, CT2 to I2, and CT3 to I3.
6
Rev 0
MAX78630+PPM Evaluation Kit User Manual
2 Installation
2.1 USB Driver Installation
This EV kit includes an isolated USB interface for serial communications with a PC. The FTDI USB controller
IC FT2232 performs the USB functions. The FTDI Windows driver presents a virtual COM port for enabling
serial communications. The FTDI Windows driver is a certified driver for Windows XP and Windows 7.
Upon attaching the MAX78630+PPM EV board to the PC, the Found New Hardware Wizard automatically
launches and installs the appropriate driver files. If your PC does not find the FTDI driver files on its local hard
disk drive, locate and reference the FTDI USB Driver and Utilities subdirectory on the CD. The FT2232
controller is powered from the USB cable and is active even when no AC power is applied to the
MAX78630+PPM EV kit.
Note: If an older FTDI driver has been previously installed, it is recommended to remove the older version
before installing this newer FTDI driver. Execute the ftdiClean.exe utility from the FTDI USB Driver and
Utilities subdirectory.
For FTDI driver support on other operating systems, refer to the FTDI website at www.ftdichip.com.
2.1.1
Confirm COM Port Mapping
•
Launch the Control Panel and click on the System icon.
•
The System Properties screen appears. Click on the Hardware tab. Click on Device Manager. Under
Ports (COM & LPT), look for the USB Serial Port assignment.
•
Take note of the COM port assignment for the USB Serial Port.
Two sequential COM
ports are associated
with the kit. Use the
second COM port
Port numbers may
differ on each PC.
2.1.2
FTDI COM Port Trouble Shooting
If the FTDI device driver did not install properly, there would be no assigned COM port number for the FTDI
controller. Repeat the USB Driver Installation, see Section 2.1.
Microsoft Windows may associate a Ball Point device to the FTDI USB controller. When this occurs a FTDI
device COM port assignment is available via HyperTerminal but there is no communications data. Verify if a
Ball Point device has been added to the “Human Interface Devices” via the Device manager. See Section 2.1.1
for access to the Device Manager. If a Ball Point device exists, delete it and unplug and replug the EV kit’s
USB cable.
Rev 0
7
MAX78630+PPM Evaluation Kit User Manual
2.2 Powering the EV Kit Board
The MAX78630+PPM EV board is normally powered through the USB port (J21).If power needs to be supplied
from a different source, a 5V DC can be applied to the connector J16; see Table 16 for the pin assignment.
When the MAX78630+PPM EV board is powered through via USB, the same cable also provides the
communications link between the host PC and the MAX78630+PPM EV board.
2.3 Basic Connection Setup
This section shows examples of basic connections between the MAX78630+PPM EV board and external
equipment. Additional connection examples can be seen in the MAX78630+PPM IC data sheet. Note that this
board does not directly support voltage transformers (VT) and provides a shunt resistor as alternative to the
current transformer on phase C.
The following examples are only a subset of all possible measurement configurations. Refer to the
MAX78630+PPM IC data sheet for configurations and system connection diagrams.
2.3.1
Wye-Connected or 3V Delta-Connected Three-Phase Systems
For Wye-connected systems, all three-phase (Line-to-Neutral) voltages are measured. The Neutral line is the
reference for all voltages (V3P3A). Jumper J11 must be in position 2-3 (3V Wye/Delta). It is also possible to
directly measure all three voltages in a Delta configuration. In that case, the Neutral is not accessible and the
MAX78630+PPM EV board is at a virtual center potential.
A
B
C
N
V2
V3
J3
V1
J2
J1
Nin J4
J11
Nout
I1
J14
J40
I2
J20
J41
CT3
C
I3
B
LOAD
J42
CT2
N
J19
CT1
J15
J39
J13
J5
J43
MAX78630EVAL V1
A
Neutral Connection for Wye Configurations
Figure 2: MAX78630+PPM EV Board Connections
8
Rev 0
MAX78630+PPM Evaluation Kit User Manual
1.
2.
3.
4.
5.
6.
7.
8.
9.
Set Jumper J11 to position 2-3.
Set Jumper J15 to position1-2.
Connect the Neutral from Source to Load and to J4 (Nin) (Wye-connected systems only).
Connect the AC source: Phase A to J1, phase B to J2 and Phase C to J3.
Connect Phase A current sensor’ secondary side to J39.
a. If using a CT, enable burden resistor by closing jumper J13. Also close jumper J14 to disable
the 2nd RC circuit.
b. If using a Rogowski coil, disable burden resistor by opening jumper J13. Also open jumper J14
to enable the 2nd RC circuit.
Connect Phase B current sensor’ secondary side to J40.
a. If using a CT, enable burden resistor by closing jumper J19. Also close jumper J20 to disable
the 2nd RC circuit.
b. If using a Rogowski coil, disable burden resistor by opening jumper J19. Also open jumper J14
to enable the 2nd RC circuit.
Connect Phase C current sensor’ secondary side to J41.
a. If using a CT, enable burden resistor by closing jumper J42. Also close jumper J43 to disable
the 2nd RC circuit
b. If using a Rogowski coil, disable burden resistor by opening jumper J42. Also open jumper J14
to enable the 2nd RC circuit
Always refer to the IC data sheet for proper connections according to the desired configuration.
Write the corresponding value of the CONFIG register to the MAX78630+PPM according to the
configuration and the choice of sensors.
Note: If a phase is backwards, reverse the current flow through the respective current sensor.
Rev 0
9
MAX78630+PPM Evaluation Kit User Manual
2.3.2
2V Delta-Connected Three-Phase Systems
For Delta-connected systems, it is possible to measure only two line (Line-to-Line) voltages. For this board,
Phase B can be used as reference (V3P3A), therefore measuring VAB and VCB. Jumper J11 must be in
position 1-2 (2V Delta).
A
B
C
V2
V3
J3
V1
J2
J1
Nin J4
J11
Nout
I1
J14
J40
J19
CT1
I2
C
I3
B
J42
J20
J41
CT3
J15
J39
J13
J5
J43
MAX78630EVAL V1
A
LOAD
Figure 3: MAX78630+PPM EV Board Connections
10
Rev 0
MAX78630+PPM Evaluation Kit User Manual
1.
2.
3.
4.
Set Jumper J11 to position 1-2.
Set Jumper J15 to position1-2.
Connect the AC source: Phase A to J1, phase B to J2 and Phase C to J3.
Connect Phase A current sensor’ secondary side to J39.
a. if using a CT, enable burden resistor by closing jumper J13. Also close jumper J14 to disable
the 2nd RC circuit.
b. if using a Rogowski coil, disable burden resistor by opening jumper J13. Also open jumper J14
to enable the 2nd RC circuit.
5. Connect Phase C current sensor’ secondary side to J41.
a. if using a CT, enable burden resistor by closing jumper J42. Also close jumper J43 to disable
the 2nd RC circuit.
b. if using a Rogowski coil, disable burden resistor by opening jumper J42. Also open jumper J14
to enable the 2nd RC circuit.
6. Always refer to the IC data sheet for proper connections according to the desired configuration.
7. Write the corresponding value of the CONFIG register to the MAX78630+PPM according to the
configuration and the choice of sensors.
Note: If a phase is backwards, reverse the current flow through the respective current sensor.
Rev 0
11
MAX78630+PPM Evaluation Kit User Manual
2.3.3
Neutral Current Measurement Considerations
It is possible, in certain Wye configurations to measure the current in the neutral conductor via a shunt resistor,
therefore replacing the third phase current measurement. This function is enabled by setting jumper J15 to
position 2-3. The MAX78630+PPM EV board then connects the shunt voltage to input AIC of the MAX78630.
IC (J41) is not measured in this case.
A
B
C
N
V2
V3
V1
J1
J2
J3
Nin J4
J11
Nout
I1
J14
J40
I2
J20
J41
I3
C
B
J42
CT2
N
J19
CT1
J15
J39
J13
J5
J43
MAX78630EVAL V1
A
LOAD
Figure 4: MAX78630+PPM EV Board Connections
12
Rev 0
MAX78630+PPM Evaluation Kit User Manual
2.4 Analog Input Jumper Descriptions
The following tables describe the various EV board jumpers that determine how analog signals are routed to
the inputs of the MAX78630+PPM.
Table 1: J15 Jumper Description
J15 Pins
Description
Default
1/2
MAX78630+PPM measures current IC (J41) -Default
Installed
2/3
MAX78630+PPM measures shunt current IN (R11)
1/2
Table 2: J11 Jumper Description
J11 Pins
Description
Default
1/2
Measure two voltages (VB is reference) -Default
Installed
2/3
Measure three voltages (N is reference)
2/3
Table 3: J13 Jumper Description
J13 Pins
Description
Default
1/2
Insert burden resistor on IA (installed: enable, open: disable)
Installed
Table 4: J19 Jumper Description
J19 Pins
Description
Default
1/2
Insert burden resistor on IB (installed: enable, open: disable)
Installed
Table 5: J42 Jumper Description
J42 Pins
Description
Default
1/2
Insert burden resistor on IC (installed: enable, open: disable)
Installed
Table 6: J14 Jumper Description
J14 Pins
Description
Default
1/2
Enable 2nd RC filter on IA (installed: disable, open: enable)
Installed
Table 7: J20 Jumper Description
J20 Pins
Description
Default
1/2
Enable 2nd RC filter on IB (installed: disable, open: enable)
Installed
Table 8: J43 Jumper Description
Rev 0
J43 Pins
Description
Default
1/2
Enable 2nd RC filter on IC (installed: disable, open: enable)
Installed
13
MAX78630+PPM Evaluation Kit User Manual
3 Serial Interfaces Selection and Configuration
The MAX78630+PPM has integrated UART, SPI (Slave), and I2C (Slave) interfaces. Only one interface can be
active at a time and the selection is done at reset/power-on.
The UART interface also supports RS-485/422. The MAX78M6630+PPM EV board includes an isolated RS485/422 transceiver.
Table 9 shows the settings of SW4 for the individual interface selection; the signal IFC0 and IFC1 are sampled
at reset and power-on.
Table 9: SW4 Serial Interface Selection
Interface Mode
SW4 1
(IFC0)
SW4 2
(IFC1)
SPI
0 (ON)
X (don’t care)
UART
1 (OFF)
0 (ON)
1 ()FF)
1 (OFF)
2
IC
The MAX78630+PPM EV board provides the serial port signals on connector J16.
3.1 UART Interface Settings
The MAX78M6630+PPM implements a serial communication protocol (SSI) that supports multipoint
communication. The device address (lower bits) is selected through the pins ADDR0 and ADDR1, as shown in
Table 10. The upper bits of the address are set through the register DEVADDR, as described in the IC data
sheet.
Table 10: SW5 Address Selection
Device Address
SW5 2
Bit 1
DEVADDR[5:1]
SW5 1
Bit 0
The EV board includes an isolated RS-485/422 transceiver. The MAX78630+PPM serial UART is connected to
the RS-485/422 transceiver when a multi-drop RS-485/422 bus is available.
UART/USB Interface and UART/RS-485/422 Interface Configuration
In order to operate the UART through the USB/FTDI device or RS-485/422, the jumper must be set according
to Table 11.
Table 11: Jumper Setting for UART/USB Interface
14
Jumper
Position
J17
1-2
J18
1-2
J28
Removed
J29
Removed
J27
Removed
J38
Removed
J30
Removed
J12
Removed
Rev 0
MAX78630+PPM Evaluation Kit User Manual
UART/RS-485/422 Interface Configuration
In order to operate the UART through the RS-485/422 transceiver, the jumpers must be set accordingly to
Table 12. Table 13 contains the pin assignment of connector J22.
Table 12: Jumpers Settings for UART/RS-485/422
Note:
Jumper
Position
J17
2-3
J18
2-3
J28
Removed
J29
Removed
J27
(See note)
J38
(See note)
J30
Removed
J12
2-3
These jumpers are used to insert a 120Ω termination on the RS-485 bus. The termination should be
inserted or removed according to the board location on the RS-485 bus.
Table 13: J22 RS-485/422 Connector Pin Assignment
J22 Pin Number
Pin Name
Pin Description
1
+5V DC
Connect to external source
2
Data In – P
Three-state, bidirectional
3
Data In – N
Three-state, bidirectional
4
Data Out – N
Three-state, bidirectional
5
Data Out – P
Three-state, bidirectional
6
GND
Connect to external source
3.2 SPI Settings
The MAX78M6630+PPM has an on-chip SPI (slave) interface. The interface is selected through SW4
according to Table 9. The SPI interface can be accessed through the USB interface or directly via J16; both
connectors are galvanically isolated.
SPI/USB Interface Configuration
Table 14: Jumper Setting for SPI/USB Interface
Rev 0
Jumper
Position
J17
1-2
J18
1-2
J28
Inserted
J29
Inserted
J27
Removed
J38
Removed
J30
Inserted
J12
1-2
15
MAX78630+PPM Evaluation Kit User Manual
SPI/J16 Interface Configuration
Table 15: Jumper Settings for Connecting on J16
Jumper
Position
J17
Removed
J18
Removed
J28
Removed
J29
Removed
J27
Removed
J38
Removed
J30
Inserted
J12
1-2
Table 16: J16 Connector Pin Assignment
16
Pin Number
Pin Name
Pin Description
1
+5V DC
Connect to external source
2
SSB
SPI Slave Select (SS)
3
MISO
Slave Data Out
4
MOSI
Slave Data Input
5
SCK
Serial Clock
6
GND
Ground
Rev 0
MAX78630+PPM Evaluation Kit User Manual
4 Graphical User Interface (GUI)
A graphical user interface (GUI) is included on the MAX78630+PPM EV kit CD to facilitate quick evaluation of
the MAX78630+PPM energy measurement device. The GUI requires Microsoft.NET Framework 4 on the PC
for which the GUI is to execute on. Upon invoking the GUI executable file, an installation wizard may appear if
Microsoft.NET Framework 4 is not installed on the PC. Follow the installation wizard instructions, or download
Microsoft.NET Framework 4 from the Microsoft web site prior to launching the GUI.
4.1 GUI Initialization
The GUI is self-explanatory when used with the MAX78630+PPM Data Sheet. The user, however, should note
the following about the EV kit hardware:
•
Serial COM Port:
Following the installation instructions in Section 2, launch the GUI executable. Click the
Connection pull-down menu and select Connect.
4.1.1
•
The COM Port / Baud Rate box appears. Select the COM port assigned to the EV kit and
leave the baud rate set to 38400 (default). Click the Connect button.
SSI ID Tab
SSI ID:
Rev 0
Click the SSI tab. Use the SSI ID number set by DIP switch 5 (1 and 2 are closed by default)
and click Set Target. Upon successful communication with the EV kit, a message appears in
the message box.
17
MAX78630+PPM Evaluation Kit User Manual
4.1.2
Device Tab
The Device tab shows to current firmware build as well as the temperature and line frequency being
measured.
4.1.3
Scaling Tab
The Scaling tab is used to set the scale factors for voltages, currents, and power results. They should be set
in accordance to the external circuitry that is being used. The scale factors are then used in the following result
tabs to convert numeric results obtained from the MAX78630+PPM device to real world values.
The user can also choose to round the results (Power, Energy, Fundamental/Harmonics, Frequency and
Temperature) to a specified number of decimal places.
18
Rev 0
MAX78630+PPM Evaluation Kit User Manual
4.1.4
Direct Tab
The Direct tab allows access to the all the registers and can both read and write to the registers. The data can
be displayed with the scale factor and units applied for convenience. In the example below, the voltage register
is being read, so the volts option is used to display the data.
Rev 0
19
MAX78630+PPM Evaluation Kit User Manual
4.1.5
Command and Configuration Tab
The Command and Config tab controls two frequently used registers:
•
Get and Set Command Register: These buttons essentially do the same thing as the direct register
reads and writes, but specifically for the command register while the Direct tab is for any pother
registers that need to be accessed. Hex and decimal formats are supported.
•
Get and Set Configuration Register: These buttons are used to set up the measurement configurations
for the MAX78630+PPM. Refer to the IC data sheet Section 2.19 for details on how this is used. The
configuration must be configured before the MAX78630+PPM is used by getting the default
configuration and setting it. Once this is done it can be saved to NV RAM for future use, or
programmed to a user-defined configuration and saved. See the Calibration tab for saving the
settings.
20
Rev 0
MAX78630+PPM Evaluation Kit User Manual
4.1.6
Calibration Tab
The Calibration tab is used to calibrate all the measurement channels. The calibration targets can be viewed
and changed and the scaling parameters are also displayed for convenience. Use the Calibration Options to
select the parameters to be calibrated. The calibration and NV RAM are also saved using the provided button.
4.1.7
Power Tab
The Power tab displays the current power being consumed by the loads. P (active power), Q (reactive power),
and S (apparent power) are displayed along with the voltage, current, crest factor, and power factor.
Rev 0
21
MAX78630+PPM Evaluation Kit User Manual
4.1.8
Energy Tab
The Energy tab displays the accumulated power both into and out of the load. All energy counters can be
reset to zero in the device with the Reset button.
4.1.9
Fundamental Tab
The Fundamental tab is used to display the fundamental and harmonic measurements for voltage, current,
and power. The harmonics displayed can be selected with the get/set harmonic buttons.
22
Rev 0
MAX78630+PPM Evaluation Kit User Manual
4.1.10 Min/Max Tab
The Min/Max tab is used to display the minimum and maximum measurements for the parameters selected in
the Word Addr column. The units can be selected with the provided pull-down menu and the most recent
measurements are updated using the get buttons. All the measurements are reset with the reset button.
Rev 0
23
MAX78630+PPM Evaluation Kit User Manual
4.1.11 Alarm Tab
The Alarm tab is a user-definable display of whatever parameters are required in a particular application. The
alarms are described in detail in Sections 2.11 and 2.12 of the MAX78630+PPM IC data sheet.
24
Rev 0
MAX78630+PPM Evaluation Kit User Manual
4.1.12 Monitor Tab
The Monitor tab is a running record of all the communications between the GUI and the target
MAX78630+PPM. A log file can be generated to save the transactions for later analysis.
Rev 0
25
MAX78630+PPM Evaluation Kit User Manual
5 Schematics, Bill of Materials, and PCB Layouts
This section includes the schematics, bill of materials, and PCB layouts for the MAX78630+PPM EV board.
5.1 MAX78630+PPM EV Board Schematics
.
J9
CON1
J8
CON1
J6
CON1
J10
CON1
V3P3
1
R3
10K
0603
V3P3A
VC
1
2
3
4
R1
1M, 0.1%
C1
0.1uF
0603
R4
750, 0.1%
0603
R2
1M, 0.1%
C2
1000pF
0603
DNP
LOGO4
1
V3P3A
J2
CON4
1
2
3
4
R5
1M, 0.1%
R6
1M, 0.1%
R7
750, 0.1%
0603
C3
0.1uF
0603
C4
1000pF
0603
1
2
3
4
R8
1M, 0.1%
R9
1M, 0.1%
R10
750, 0.1%
0603
C5
0.1uF
0603
C6
1000pF
0603
SW1
MAXIM
6610 Reset
GND
V3P3A
J3
CON4
V3P3A
1
2
3
V3P3A
J11
CON3
Jumper
Pos 1-2: 2V Delta (VB is ref erence)
Pos 2-3: 3V Wy e/Delta
J7
CON18
SIP100P18
V3P3
R21
0
0603
V3P3A
GND
C38
0.1uF
0603
C39
0.1uF
0603
GND
24
J5
CON4
1
2
3
4
R11
0.004, 1%, 2.5W R12
750, 0.1%
2512P
0603
C7
0.1uF
0603
C8
1000pF
0603
25
26
27
AV1
AV2
AV3
RESETB
DIO0
DIO1
DIO2
DIO3
DIO4
DIO5
DIO6
DIO7
DIO8
DIO9
DIO10
DIO11
DIO12
DIO13
DIO14
DIO15
Jumper J15
Pos 1-2: 3I
Pos 2-3: 2I + Shunt on Neutral
J15
IA
28
32
R13
4.99, 1%
1210
R14
750, 0.1%
0603
C9
0.1uF
0603
C10
0.047uF
0603
RES1
RES2
C11
1000pF
0603
V3P3A
1
2
IB
J40
Block2
5.08 mm/2
1
2
J20
CON2
SIP100P2
XIN
XOUT
23
GND
20
18
17
16
9
8
6
4
3
22
21
19
10
7
5
2
AL1
SPCK/ADDR0
SDI/RX/SDAI
SDO/TX/SDAO
AL2
SSB/DIR/SCL
AL3/ADDR1
AL4
IFC0
IFC1
AL5
SGNV1
SGNV2
SGNV3
SPCK SCK
SDI
MOSI
SDO MISO
SSB
12
13
J19
CON2
SIP100P2
R16
4.99, 1%
1210
1
Y1
2
R38
10K
0603
20.00MHz
GND
C12
0.1uF
0603
SW5
SW DIP-2
C13
0.047uF
0603
C14
1000pF
0603
R19
4.99, 1%
1210
J42
CON2
SIP100P2
R33
10K
0603
method used. SW4 can be set to
SW4
SW DIP-2 1s after power-up to free up the
GPIO lines
I2C Address Bits
SW2 determines
ADDR0 and ADDR1
COMMUNICATIONS
MODE
R79
1K
1
1
1
IC
1
2
R39
10K
0603
The state of SW4 at power-up
determines the communications
R18
750, 0.1%
0603
R78
1K
R80
1K
R77
1K
Test points Currents
J43
CON2
SIP100P2
Optional RC f or Rogowski Coils
(Close Jumper f or CT)
CON1
J44
CON1
J45
CON1
J46
R20
750, 0.1%
0603
SPI
0x
UART 10
I2C
11
GND
1
2
Insert Burden Resistor
(Close Jumper f or CT)
J41
Block2
5.08 mm/2
R36
10K
0603
GND
V3P3A
1
2
V3P3
C19
18pF
0603
C18
18pF
0603
Optional RC f or Rogowski Coils
(Close Jumper f or CT)
R17
750, 0.1%
0603
SSB
V3P3
U1
MAX78630-32
QFN32L
GND
V3P3
1
2
Insert Burden Resistor
(Close Jumper f or CT)
GNDD
GNDD
1
2
V3P3A
CON3
R15
750, 0.1%
0603
GNDA
J39
Block2
5.08 mm/2
J13
CON2
SIP100P2
1
1
2
AI1
AI2
AI3
14
15
Insert Burden Resistor
(Close Jumper f or CT)
1
2
CT secondary inputs
29
30
31
3
2
1
J14
CON2
SIP100P2
Optional RC f or Rogowski Coils
(Close Jumper f or CT)
C40
0.1uF
0603
11
GND
V3P3D
Nout
1
2
3
4
V3P3A
Nin
J4
CON4
DIO connector
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
VB
J1
CON4
Warning
DIO15
DIO14
SGNV3/DIO13
SGNV2/DIO12
SGNV1/DIO11
AL5/DIO10
IFC1/DIO9
IFC0/DIO8
AL4/DIO7
AL3/ADDR0/DIO6
SSB/DIR/SCL/IFC1/DIO5
AL2/DIO4
SDO/TX/SDAO/DIO3
SDI/RX/SDAI/DIO2
SPCK/ADDR0/DIO1
AL1/DIO0
VA
DNP
LOGO1
1
1
1
1
Test points Voltages
Voltage inputs
R22
750, 0.1%
0603
C15
0.1uF
0603
C16
0.047uF
0603
C17
1000pF
0603
V3P3A
MT1
MT2
MT3
MT4
PCB Peg
PCB Peg
PCB Peg
PCB Peg
Maxim - Teridian Smart Grid Solutions
Title
MAX78630TQFN32EVALV1
Size
B
Document Number
MAX78630 TQFN32 Ev aluation Board
Date:
Friday , April 12, 2013
Rev
1
Sheet
1
of
2
Figure 5: MAX78630+PPM EV Board Electrical Schematic (1 of 2)
26
Rev 0
MAX78630+PPM Evaluation Kit User Manual
.
R40
0
0603
5VUSB
Isolation
AVCC
GND
R45
0
0603
R57
1K
0603
U7
1
2 VDD1VDD2
3 GND1GND2
4 IN1 OUT1
5 IN2 OUT2
6 OUT3 IN3
7 OUT4 IN4
NC
8 NC
GND GND1GND2
IL516-3E
R56 1K
0603
SCKout
V3P3
SCK SPCK
SPCK
V3P3
8
7
6
5
SSB/TXEN SSB
SSB
C31
MISOF
MISOout
1
2
3
40
39
38
37
36
35
33
32
30
29
28
27
26
MOSIF
MOSIin
SCKin
R49
0
0603
U8
Vdd2
Vdd1
Voe
IN
OUT SY NC
GND2 GND1
1
2
3
4
SSBin
1
2
3
IL510-3E
J18
CON3
SSBout
GND
1
2
3
RS485TXEN
BD0
BD1
BD2
BD3
BD4
BD5
BD6
BD7
BC0
BC1
BC2
BC3
SI/WUB
U3
FT2232C
TQFP48
RS485/USB
Select
0603
0.1uF
J12
CON3
RS485
TXen/
SSB
Select
16
15
14
13
12
11
10
9
2
1
J30
SSBF
2
1
GND
MISOin
SIP100P2
CON2
J29
46
VCC2
VCC1
AVCC
PWREN
3V3OUT
RESETB
USBDM
USBDP
RSTOUTB
C25
0.033uF
0603
41
6
USB3
J21
USB
4
R46
500 ma Max
2.2K
0603
8
7
USBDM
USBDP
5
RSTOB
XTI
XTIN
XTOUT
43
44
R50
1M
0603
TEST
USB
SPI &
UART
2
Y2
6MHz
XTO
EESK
EECS
EEDATA
C27
10uF
0805
R47
2.2K
0603
1
2
3
4
5
6
1
C28
0.1uF
0603
SDO
SDI
MISO SDO
MOSI SDI
R58
1K
0603
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
AC0
AC1
AC2
AC3
S1/WUA
AGND
5VIN
C26
0.1uF
0603
24
23
22
21
20
19
17
16
15
13
12
11
10
1
48
2
47
R53
10K
0603
45
RXFTDI
V3P3
C24
0.1uF
0603
C23
0.1uF
0603
31
14
SIP100P2
J28 CON2
42
3
1
R43
10K
0603
VCCIOB
VCCIOA
GND
5VIN
C21
10uF
0805
GND4
GND3
GND2
GND1
GND
R41
470
0603
34
25
18
9
VGND
R42
10K
0603
2
1
C20
10uF
VIN
VOUT
NC4
NC3
NC2
NC1
TX/RX
wireOR
Select
4
2
8
7
6
3
+5VISO
5
C22
0.1uF
0603
5VIN
VR2
VBT1-5V
+5VISO
J16
CON6
SIP100P6
3
6
5
4
3
2
1
Optional External I2C or SPI
J17
CON3
RS485/USB
Select
R54
10K
0603
GND
R59
120
0805
2
1
5VIN
C29
0.1uF
0603
RS485RX
RS485TXENout
VR3
3.3V @ 950mA
V3P3
LD1117S33CTR
C53
1000pF
0603
C54
0.1uF
0603
GND
VOUT
GND
C52
10uF
0805
TAB
1
4
2
VIN
SOT223
RS485TXENout
U11
1
2
3
4
5
6
7
VL
RO
DE
RE
DI
GND
NC
VCC
NC
A
B
Z
Y
GND
MAX13433EESD+
3
+5VISO
C55
0.1uF
0603
GND
+5VISO
14
13
12
11
10
9
8
R52
120
0805
2
1
C30
1uF
0603
J38
CON2
SIP100P2
5VIN
RS485A
RS485B
RS485Z
RS485Y
J27
CON2
SIP100P2
1
2
3
4
5
6
J22
Block6
RS485
Do NOT apply +5VDC to
J22-1 when USB cable is
attached to J21.
GND
Maxim - Teridian Smart Grid Solutions
Title
MAX78630TQFN32EVALV1
Size
B
Document Number
MAX78630 TQFN32 Dev elopment Board
Date:
Friday , April 12, 2013
Sheet
Rev
1
2
of
2
Figure 6: MAX78630+PPM EV Board Electrical Schematic (2 of 2)
Rev 0
27
MAX78630+PPM Evaluation Kit User Manual
5.2 MAX78630+PPM EV Board Bill of Materials
Table 17: MAX78630+PPM EV Board Bill of Materials
Item Quantity Reference
C1,C3,C5,C7,C9,C12,C15,C22,C23,C24,
1
19 C26,C28,C29,C31,C38,C39,C40,C54,C55
2
8 C2,C4,C6,C8,C11,C14,C17,C53
3
3 C10,C13,C16
4
2 C18,C19
5
4 C20,C21,C27,C52
6
1 C25
7
1 C30
8
5 J1,J2,J3,J4,J5
9
7 J6,J8,J9,J10,J44,J45,J46
10
1 J7
11
5 J11,J12,J15,J17,J18
12
11 J13,J14,J19,J20,J27,J28,J29,J30,J38,J42,J43
13
1 J16
14
1 J21
15
1 J22
16
3 J39,J40,J41
17
4 MT1,MT2,MT3,MT4
18
6 R1,R2,R5,R6,R8,R9
19
9 R3,R33,R36,R38,R39,R42,R43,R53,R54
20
10 R4,R7,R10,R12,R14,R15,R17,R18,R20,R22
21
1 R11
22
3 R13,R16,R19
28
Part
PCB Footprint
0.1uF
1000pF
0.047uF
18pF
10uF
0.033uF
1uF
CON4
CON1
CON18
CON3
CON2
CON6
USB
Block6
Block2
PCB Peg
1M, 0.1%
10K
750, 0.1%
0.004, 1%, 2.5W
4.99, 1%
603
603
603
603
805
603
603
STERM
SIP100P1
SIP100P18
SIP100P3
SIP100P2
SIP100P6
USBB
TERM BLK 200-6
5.08 mm/2
MTGPS.PRT
1206W
603
603
2512P
1210
Rev 0
MAX78630+PPM Evaluation Kit User Manual
Table 17 continued
Item Quantity Reference
23
4 R21,R40,R45,R49
24
1 R41
25
2 R46,R47
26
1 R50
27
2 R52,R59
28
7 R56,R57,R58,R77,R78,R79,R80
29
1 SW1
30
2 SW4,SW5
31
1 U1
32
1 U3
33
1 U7
34
1 U8
35
1 U11
36
1 VR2
37
1 VR3
38
1 Y1
39
1 Y2
Rev 0
Part
0
470
2.2K
1M
120
1K
PUSHBUTTON
SW DIP-2
MAX78630-32
FT2232C
IL516-3E
IL510-3E
MAX13433EESD+
VBT1-5V
3.3V @ 950mA
20.00MHz
6MHz
PCB Footprint
603
603
603
603
805
603
EP11
DIP4
QFN32L
TQFP48
SO-16 NARROW
IL611A
SO-14 NARROW
VBT1
SOT223
ABLS
CSTCR
29
MAX78630+PPM Evaluation Kit User Manual
5.3 MAX78630+PPM EV Board PCB Layouts
Figure 7: MAX78630+PPM EV Board PCB Top View
30
Rev 0
MAX78630+PPM Evaluation Kit User Manual
Figure 8: MAX78630+PPM EV Board PCB Bottom View
Rev 0
31
MAX78630+PPM Evaluation Kit User Manual
6 Contact Information
For more information about Maxim products or to check the availability of the MAX78630+PPM, contact
technical support at www.maximintegrated.com/support.
Revision History
REVISION
NUMBER
REVISION
DATE
0
7/13
32
DESCRIPTION
Initial release
PAGES
CHANGED
—
Rev 0
工商网监
湘ICP备2023018690号
