19-3860; Rev 0; 12/05
KIT
ATION
EVALU
E
L
B
AVAILA
Quad Audio Line Driver with 3VRMS Output
The MAX9727 quad audio line driver with 3VRMS output is
ideal for portable audio devices where board space and
cost is at a premium. The device uses Maxim’s
DirectDriveTM architecture that produces a ground-referenced output from a single supply, eliminating the need
for large DC-blocking capacitors and saving cost, board
space, and component height. A high 100dB PSRR and
low 0.0005% THD+N ensures clean, low-distortion amplification of the audio signal. Each MAX9727 amplifier can
provide 3VRMS to a 1kΩ load with less than 0.003%
THD+N while operating from a single +5V supply. Each
MAX9727 amplifier can provide 2VRMS to a 1kΩ load with
less than 0.003% THD+N while operating from a single
+3.3V supply.
A shutdown input disables the amplifiers and reduces
quiescent current consumption to less than 100nA. The
MAX9727 features Maxim’s comprehensive click-andpop suppression circuitry that reduces audible clicks and
pops during startup and shutdown.
The MAX9727 operates from a single 2.7V to 5.5V supply, consumes only 3mA of supply current per channel,
and is specified over the -40°C to +85°C extended temperature range.
Applications
Features
o 2.7V to 5.5V Single-Supply Operation
o High 100dB PSRR
o 109dB Signal-to-Noise Ratio (SNR)
o
o
o
o
o
Ground-Referenced Outputs
No Audible Clicks or Pops at Power-Up/Down
Differential Inputs
3VRMS into 1kΩ Load at 5V
2VRMS into 1kΩ Load at 3.3V
o 3mA Supply Current Per Channel
o Unity-Gain Stable
o 100nA Low-Power Shutdown Mode
o CLOAD Drive > 220pF
o ±8kV HBM ESD-Protected Outputs
Ordering Information
PART
TEMP RANGE
PINPACKAGE
MAX9727EEP+
-40°C to +85°C
20 QSOP
GAIN
Adjustable
+Denotes lead-free package.
Simplified Block Diagram
Set-Top Boxes
CD and DVD Players
Consumer and
Professional Audio
Equipment
Soundcards
Portable Audio
Devices
A/V Receivers
OUTA
OUTD
INA-
IND-
INA+
IND+
INB+
INC+
INB-
INC-
OUTB
OUTC
SHDN
PVSS
Pin Configuration
TOP VIEW
+
OUTA 1
20 OUTD
INA- 2
19 IND-
INA+ 3
18 IND+
VDD 4
MAX9727
INB+ 5
17 VSS
16 INC+
INB- 6
15 INC-
OUTB 7
14 OUTC
SHDN 8
13 PVSS
PVDD 9
12 C1N
C1P 10
11 PGND
ON
OFF
PVDD
C1P
MAX9727
PGND
C1N
QSOP
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX9727
General Description
MAX9727
Quad Audio Line Driver with 3VRMS Output
ABSOLUTE MAXIMUM RATINGS
VDD, PVDD to PGND .................................................-0.3V to +6V
VSS, PVSS to PGND ..................................................-6V to +0.3V
IN_ to PGND ..................................(VSS + 0.3V) to (PVDD - 0.3V)
OUT_ to PGND...............................(VSS - 0.3V) to (PVDD + 0.3V)
SHDN to PGND..........................(PGND - 0.3V) to (PVDD + 0.3V)
C1P to PGND.............................(PGND - 0.3V) to (PVDD + 0.3V)
C1N to PGND .............................(PVSS - 0.3V) to (PGND + 0.3V)
Output Short Circuit to PGND or PVDD .......................Continuous
Continuous Power Dissipation (TA = +70°C)
20-Pin QSOP Single-Layer Board
(derate 9.1mW/°C above +70°C) ..................................727mW
20-Pin QSOP Multilayer Board
(derate 11mW/°C above +70°C) ...................................884mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature .....................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VDD = PVDD = 3.3V, PGND = 0V, SHDN = VDD, VCM = 0V, C1 = C2 = 1µF, RIN = RF = 5kΩ, RL = ∞, TA = TMIN to TMAX. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
GENERAL
Supply Voltage Range
VDD
Inferred from PSRR test
5.5
V
Quiescent Current
IDD
Current into VDD and PVDD
2.7
12
14
mA
Shutdown Current
IDD, SHDN
VSHDN = 0V
0.1
10
µA
±5
mV
AMPLIFIERS
Input Offset Voltage
VOS
±0.5
Input Bias Current
IBIAS
1000
nA
Input Offset Current
IOS
500
nA
Open-Loop Gain
AV
82
dB
Input Common-Mode Voltage
Range
Common-Mode Rejection Ratio
Power-Supply Rejection Ratio
CMR
CMRR
PSRR
Output Voltage
Output Voltage Swing
Output Short-Circuit Current
2
VOUT
ISC
VOUT = -3V to +3V, RL = 1kΩ
VDD = 2.7V
-1.6
+1.6
VDD = 3V
-2.3
+2.3
VDD = 5V
-3.5
+3.5
VDD = 2.7V, VCM = ±1.6V
80
100
VDD = 3V, VCM = ±1.9V
80
100
VDD = 5V, VCM = ±3.5V
80
100
VDD = PVDD = 2.7V to 5.5V
80
100
f = 1kHz, VDD = PVDD = 5V + 100mVP-P
ripple
60
RL = 1kΩ, VDD = 3.3V, THD+N = 1%
1.6
2.0
RL = 1kΩ, VDD = 5V, THD+N = 1%
2.0
3.0
RL = 1kΩ,
VDD = 3.3V
Positive
2.6
3.0
Negative
-2.6
-3.0
RL = 1kΩ,
VDD = 5V
Positive
3.5
4.2
Negative
-3.5
-4.1
Sinking
40
Sourcing
5
_______________________________________________________________________________________
V
dB
dB
VRMS
V
mA
Quad Audio Line Driver with 3VRMS Output
(VDD = PVDD = 3.3V, PGND = 0V, SHDN = VDD, VCM = 0V, C1 = C2 = 1µF, RIN = RF = 5kΩ, RL = ∞, TA = TMIN to TMAX. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
Total Harmonic Distortion Plus
Noise
SYMBOL
THD+N
CONDITIONS
MIN
0.0005
VOUT = 2VRMS, BW = 22Hz to 22kHz,
f = 1kHz, unweighted, RL = 10kΩ
0.0006
VOUT = 1.6VRMS, BW = 22Hz to 22kHz,
f = 1kHz, unweighted, RL = 1kΩ
Signal-to-Noise Ratio
Click-and-Pop Level
SNR
KCP
Slew Rate
tON
Turn-Off Time
tOFF
Capacitive Drive
CL
Crosstalk
MAX
UNITS
%
0.003
VOUT = 1.6VRMS,
RL = 1kΩ
22Hz to 22kHz
109
VOUT = 2VRMS,
RL = 1kΩ
22Hz to 22kHz
A-weighted
115.5
Peak voltage,
A-weighted, 32
samples/s (Notes 2, 3)
Into shutdown
-62.2
Out of shutdown
-54.3
A-weighted
113.6
dB
111
dBV
RL = 1kΩ, CL = 100pF
Turn-On Time
TYP
VOUT = 1.6VRMS, BW = 22Hz to 22kHz,
f = 1kHz, unweighted, RL = 10kΩ
0.9
V/µs
90
µs
1
µs
No sustained oscillations
220
pF
f = 10kHz
-70
dB
dB
Large-Signal Open-Loop Gain
AVOL
VOUT = 2VRMS
82
Small-Signal Open-Loop Gain
AVOS
VOUT = 100mVRMS
95
dB
Gain Bandwidth
GBW
3
MHz
Charge-Pump Switching
Frequency
fOSC
Charge-Pump Output Impedance
ESD Protection
ESD
150
300
450
kHz
Measured at PVSS
20
Ω
HBM
±8
kV
DIGITAL INPUTS (SHDN)
Input-Voltage High
VIH
Input-Voltage Low
Input Leakage Current
2.0
V
VIL
0.8
V
ILEAK
±1
µA
Note 1: All devices are 100% tested at TA = +25°C. Specifications over temperature are guaranteed by design.
Note 2: Inputs AC-coupled to PGND.
Note 3: Click-and-pop testing performed with a 1kΩ resistive load connected to ground. Mode transitions are controlled by SHDN.
KCP level is calculated as 20log[(peak voltage during mode transition, no input signal)/1VRMS]. Units are expressed in dBV.
_______________________________________________________________________________________
3
MAX9727
ELECTRICAL CHARACTERISTICS
Typical Operating Characteristics
(VDD = PVDD = 3.3V, VCM = 0V, RIN = RF = 5kΩ, THD+N measurement bandwidth = 22Hz to 22kHz, TA = +25°C, unless otherwise
noted.)
f = 10kHz
f = 100Hz
RL = 5kΩ
0.01
0.001
0.001
RL = 1kΩ
0
1
2
3
0.1
MAX9727 toc03
f = 100Hz
0.001
0.0001
0
4
f = 1kHz
0.01
0.0001
0.0001
1
2
3
0
4
1
2
3
OUTPUT VOLTAGE (VRMS)
OUTPUT VOLTAGE (VRMS)
OUTPUT VOLTAGE (VRMS)
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. OUTPUT VOLTAGE
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. FREQUENCY
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. FREQUENCY
0.01
RL = 1kΩ
0.01
VOUT = 2.5VRMS
THD+N (%)
THD+N (%)
0.1
VDD = 5V
RL = 10kΩ
VOUT = 2.5VRMS
0.01
RL = 5kΩ
MAX9727 toc06
VDD = 5V
RL = 1kΩ
1
0.1
MAX9727 toc05
VDD = 3.3V
fIN = 1kHz
10
0.1
MAX9727 toc04
100
THD+N (%)
RL = 10kΩ
0.1
0.01
f = 10kHz
1
THD+N (%)
0.1
VDD = 3.3V
RL = 1kΩ
10
1
f = 1kHz
THD+N (%)
THD+N (%)
1
VDD = 5V
fIN = 1kHz
10
100
MAX9727 toc02
VDD = 5V
RL = 1kΩ
10
100
MAX9727 toc01
100
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. OUTPUT VOLTAGE
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. OUTPUT VOLTAGE
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. OUTPUT VOLTAGE
VOUT = 1VRMS
0.001
0.001
VOUT = 1VRMS
0.001
RL = 10kΩ
0.0001
0.0001
0.0001
0
1
2
3
10
100
1k
10k
10
100k
100
1k
10k
100k
OUTPUT VOLTAGE (VRMS)
FREQUENCY (Hz)
FREQUENCY (Hz)
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. FREQUENCY
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. FREQUENCY
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. COMMON-MODE VOLTAGE
VOUT = 2VRMS
0.01
VOUT = 1VRMS
0.001
0.001
VDD = 5V
RL = 1kΩ
DIFFERENTIAL
CONFIGURATION
f = 10kHz
0.01
VOUT = 2VRMS
THD+N (%)
0.01
0.1
MAX9727 toc09
VDD = 3.3V
RL = 10kΩ
THD+N (%)
VDD = 3.3V
RL = 1kΩ
MAX9727 toc08
0.1
MAX9727 toc07
0.1
THD+N (%)
MAX9727
Quad Audio Line Driver with 3VRMS Output
f = 1kHz
0.001
VOUT = 1VRMS
f = 100Hz
0.0001
100
1k
FREQUENCY (Hz)
4
0.0001
0.0001
10
10k
100k
10
100
1k
FREQUENCY (Hz)
10k
100k
-4
-2
0
2
COMMON-MODE VOLTAGE (V)
_______________________________________________________________________________________
4
Quad Audio Line Driver with 3VRMS Output
3.0
THD+N = 10%
2.5
2.0
THD+N = 1%
3.5
3.0
THD+N = 10%
THD+N = 1%
2.5
VDD = 3.3V
2.5
OUTPUT VOLTAGE (VRMS)
3.5
VDD = 5V
4.0
3.0
MAX9727 toc11
MAX9727 toc10
4.5
OUTPUT VOLTAGE (VRMS)
OUTPUT VOLTAGE (VRMS)
4.0
fIN = 1kHz
RL = 1kΩ
OUTPUT VOLTAGE
vs. LOAD RESISTANCE
OUTPUT VOLTAGE
vs. LOAD RESISTANCE
2.0
1.5
MAX9727 toc12
OUTPUT VOLTAGE
vs. SUPPLY VOLTAGE
2.0
THD+N = 10%
THD+N = 1%
1.5
1.0
1.0
0.5
1.5
0.5
3.0
3.5
4.0
4.5
5.5
5.0
0
2
4
6
0
10
GAIN AND PHASE
vs. FREQUENCY
OUTPUT VOLTAGE (V)
C1 = C2 = C3 = 1µF
0
-1
-2
-3
C1 = C2 = C3 = 1µF
-4
C1 = C2 = C3 = 0.22µF
-3.0
60
-60
PHASE
-120
C1 = C2 = C3 = 0.1µF
80
120
100
0
50
100
150
-180
0.1
200
1
10
100
1000
OUTPUT CURRENT (mA)
FREQUENCY (kHz)
POWER-SUPPLY REJECTION RATIO
vs. FREQUENCY
CROSSTALK vs. FREQUENCY
CROSSTALK vs. FREQUENCY
VDD = 5V
VOUT = 3VRMS
RL = 1kΩ
-90
-80
MAX9727 toc17
-80
MAX9727 toc16
RL = 1kΩ
VDD = 3.3V
VOUT = 2VRMS
RL = 1kΩ
-90
-40
VDD = 5V + 100mVP-P
CROSSTALK (dB)
CROSSTALK (dB)
-20
-30
-100
-110
Ch. D to Ch. A
-120
Ch. D to Ch. B
-60
-130
-70
1k
FREQUENCY (Hz)
10k
100k
-110
Ch. D to Ch. C
-120
Ch. D to Ch. B
Ch. D to Ch. C
-140
100
Ch. D to Ch. A
-100
-130
VDD = 3.3V + 100mVP-P
-80
10,000
MAX9727 toc18
OUTPUT CURRENT (mA)
0
PSRR (dB)
GAIN
-5
-6
40
0
C1 = C2 = C3 = 0.22µF
C1 = C2 = C3 = 0.1µF
20
10
AV = 60dB
60
GAIN/PHASE (dB/DEGREES)
VDD = 5V
OUTPUTS UNLOADED,
CHARGE-PUMP LOAD
CONNECTED BETWEEN
PVSS AND PGND
2
-2.5
MAX9727 toc14
MAX9727 toc13
-1.5
-2.0
3
1
-1.0
10
8
CHARGE-PUMP OUTPUT VOLTAGE
vs. OUTPUT CURRENT
0
-50
6
CHARGE-PUMP OUTPUT VOLTAGE
vs. OUTPUT CURRENT
-0.5
-10
4
LOAD RESISTANCE (kΩ)
VDD = 3.3V
OUTPUTS UNLOADED,
CHARGE-PUMP LOAD
CONNECTED BETWEEN
PVSS AND PGND
0
2
LOAD RESISTANCE (kΩ)
0.5
-3.5
8
SUPPLY VOLTAGE (V)
1.0
OUTPUT VOLTAGE (V)
0
0
2.5
MAX9727 toc15
1.0
-140
10
100
1k
FREQUENCY (Hz)
10k
100k
10
100
1k
10k
100k
FREQUENCY (Hz)
_______________________________________________________________________________________
5
MAX9727
Typical Operating Characteristics (continued)
(VDD = PVDD = 3.3V, VCM = 0V, RIN = RF = 5kΩ, THD+N measurement bandwidth = 22Hz to 22kHz, TA = +25°C, unless otherwise
noted.)
Typical Operating Characteristics (continued)
(VDD = PVDD = 3.3V, VCM = 0V, RIN = RF = 5kΩ, THD+N measurement bandwidth = 22Hz to 22kHz, TA = +25°C, unless otherwise
noted.)
OUTPUT AT 2VRMS AT 1kHz
(VDD = 5V, RL = 1kΩ)
VSHDN
2V/div
MAX9727 toc21
VSHDN
2V/div
MAX9727 toc20
EXITING SHUTDOWN
MAX9727 toc19
ENTERING SHUTDOWN
OUTA
5V/div
OUTB
5V/div
VIN_
5V/div
VIN_
5V/div
OUTC
5V/div
VOUT_
5V/div
OUTD
5V/div
VOUT_
5V/div
STEP RESPONSE
SUPPLY CURRENT vs. TEMPERATURE
12.5
SUPPLY CURRENT (mA)
VIN_
50mV/div
VOUT_
50mV/div
13.0
VOUT_
50mV/div
MAX9727 toc24
STEP RESPONSE
400µs/div
MAX9727 toc23
40µs/div
MAX9727 toc22
20µs/div
VIN_
50mV/div
NO LOAD
INPUTS GROUNDED
VDD = 5V
VDD = 3.3V
12.0
11.5
11.0
VDD = 2.7V
10.5
RL = 1kΩ
CL = 220pF
10.0
-50
1µs/div
3
VDD = 3.3V
2
1
50
VDD = 5V
VOUT = -60dBV
fIN = 1kΩ
-50
-60
-70
-80
-90
-100
-110
-120
0
-130
VDD = 2.7V
-140
-150
-1
-50
-25
0
25
50
TEMPERATURE (°C)
6
-40
AMPLITUDE (dBV)
VDD = 5V
25
OUTPUT SPECTRUM
vs. FREQUENCY
MAX9727 toc25
4
NO LOAD
INPUTS GROUNDED
0
TEMPERATURE (°C)
SHUTDOWN CURRENT vs. TEMPERATURE
5
-25
MAX9727 toc26
1µs/div
SHUTDOWN CURRENT (nA)
MAX9727
Quad Audio Line Driver with 3VRMS Output
75
100
0
5
10
15
FREQUENCY (kHz)
_______________________________________________________________________________________
20
75
100
Quad Audio Line Driver with 3VRMS Output
OUTPUT NOISE DENSITY
vs. FREQUENCY
-70
-80
-90
-100
-110
-120
-130
OUTPUT BACKDRIVEN DURING SHUTDOWN
MAX9727 toc28
-60
25
VOLTAGE-NOISE DENSITY (µV/ Hz)
VDD = 5V
VIN = 0V
-50
AMPLITUDE (dBV)
MAX9727 toc27
-40
VDD = 3.3V
RL = 1kΩ
20
SIGNAL
SOURCE
2V/div
15
OUT_
2V/div
10
5
MAX9727 toc29
OUTPUT NOISE SPECTRUM
vs. FREQUENCY
SHDN = 0V
EXTERNAL SIGNAL SOURCE
CONNECTED TO OUTPUT
RSOURCE = 100Ω
VSS
100mV/div
-140
0
-150
0
5
10
15
20
FREQUENCY (kHz)
0
5
10
15
20
1ms/div
FREQUENCY (kHz)
Pin Description
PIN
NAME
FUNCTION
1
OUTA
2
INA-
Inverting Input A
3
INA+
Noninverting Input A
4
VDD
Analog Positive Supply. Bypass with a 0.1µF capacitor to PGND.
5
INB+
Noninverting Input B
6
INB-
Inverting Input B
Output A
7
OUTB
Output B
8
SHDN
Active-Low Shutdown Input. Connect SHDN to VDD for normal operation.
9
PVDD
Charge-Pump Positive Supply. Bypass with a 1µF capacitor to PGND.
10
C1P
Charge-Pump Flying Capacitor Positive Terminal. Connect a 1µF capacitor between C1P and C1N.
11
PGND
12
C1N
Charge-Pump Flying Capacitor Negative Terminal. Connect a 1µF capacitor between C1P and C1N.
13
PVSS
Charge-Pump Negative Supply. Bypass with a 1µF capacitor to PGND.
14
OUTC
15
INC-
16
INC+
17
VSS
18
IND+
Noninverting Input D
19
IND-
Inverting Input D
20
OUTD
Power Ground
Output C
Inverting Input C
Noninverting Input C
Amplifier Negative Rail. Connect to PVSS.
Output D
_______________________________________________________________________________________
7
MAX9727
Typical Operating Characteristics (continued)
(VDD = PVDD = 3.3V, VCM = 0V, RIN = RF = 5kΩ, THD+N measurement bandwidth = 22Hz to 22kHz, TA = +25°C, unless otherwise
noted.)
MAX9727
Quad Audio Line Driver with 3VRMS Output
Detailed Description
The MAX9727 is a quad audio line driver with an output
of 3VRMS from a single +5V supply and 2VRMS from a
single +3.3V supply. The device employs Maxim’s
DirectDrive architecture that produces a ground-referenced output from a single supply, eliminating the
need for large DC-blocking capacitors. An internal
charge pump creates an internal negative supply voltage. This allows the amplifier outputs of the MAX9727
to be biased at GND, almost doubling dynamic range
while operating from a single supply.
An active-low shutdown input disables the amplifiers
and reduces quiescent current consumption to less
than 100nA.
The MAX9727 also features click-and-pop suppression
circuitry that reduces audible clicks and pops during
startup and shutdown.
DirectDrive
Maxim’s DirectDrive architecture uses a charge pump
to create an internal negative supply voltage, allowing
the MAX9727 outputs to be biased about ground. This
allows for a symmetrical output biased around 0V. The
MAX9727’s charge pump requires two small ceramic
capacitors, conserving board space, reducing cost,
and improving the frequency response of the amplifiers. See the Charge-Pump Output Voltage vs. Output
Current graphs in the Typical Operating Characteristics
for details of the possible capacitor sizes. There is a
low DC voltage on the amplifier outputs due to amplifier
offset. However, the offsets of the MAX9727 are typically 500µV, which, when combined with a 1kΩ load,
results in less than 500nA of DC current flow to the linein device.
Charge Pump
The MAX9727 features a low-noise charge pump. The
300kHz switching frequency is well beyond the audio
range and does not interfere with audio signals. The
switch drivers feature a controlled switching speed that
minimizes noise generated by turn-on and turn-off transients. The di/dt noise caused by the parasitic bond
wire and trace inductance is minimized by limiting the
8
VOUT
VDD
VDD
VDD/2
GND
CONVENTIONAL DRIVER BIASING SCHEME
VOUT
VDD
2VDD
GND
VDD
DirectDrive BIASING SCHEME
Figure 1. Conventional Driver Output Waveform vs. MAX9727
Output Waveform
switching speed of the charge pump. Although not typically required, additional high-frequency noise attenuation can be achieved by increasing the value of C2
(see the Functional Diagram/Typical Operating Circuit).
_______________________________________________________________________________________
Quad Audio Line Driver with 3VRMS Output
Click-and-Pop Suppression
In conventional single-supply audio amplifiers, the output-coupling capacitor contributes significantly to audible clicks and pops. Upon startup, the amplifier charges
the coupling capacitor to its bias voltage, typically half
the supply. Likewise, on shutdown, the capacitor is discharged. This results in a DC shift across the capacitor,
which appears as an audible transient at the speaker
connected to the output of the power amplifier of the
audio system. Since the MAX9727 does not require output-coupling capacitors, this problem does not arise.
Additionally, the MAX9727 features extensive click-andpop suppression that eliminates any audible transient
sources internal to the device.
In some applications, the output of the device driving
the MAX9727 may have a DC bias. At startup, the
input-coupling capacitor is charged to the input
device’s DC-bias voltage through the input and feedback resistors of the MAX9727, resulting in a DC shift
across the capacitor and an audible click/pop. Delay
the rise of SHDN 4 to 5 time constants based on RIN
and CIN (4 x RIN x CIN), relative to the startup of the
input device, to eliminate clicks-and-pops caused by
the input filter.
Applications Information
Differential Input Configuration
Figure 2 shows a single channel of the MAX9727 configured as a differential input amplifier. A differential
input offers improved noise immunity over a singleended input. In systems that include high-speed digital
circuitry, high-frequency noise can couple into the
amplifier’s input traces. The signals appear at the
amplifier’s inputs as common-mode noise. A differential
input amplifier amplifies the difference of the two
inputs, and signals common to both inputs are subtracted out. When configured for differential inputs, the
voltage gain of the MAX9727 is set by:
AV =
RF1
RIN1
where AV is the desired voltage gain in V/V. RIN1 must
be equal to RIN2, and RF1 must be equal to RF2.
The common-mode rejection ratio (CMRR) is limited by
the external resistor-matching. Ideally, to achieve the
highest possible CMRR the following condition should
be met:
RF1
R
= F2
RIN1 RIN2
RF1
MAX9727
RIN1
IN_OUT_
RIN2
IN_+
Amplifier Configurations
The MAX9727 works in many standard op-amp configurations such as inverting, noninverting, voltage follower, summing, difference, active filters, and many others.
No special design considerations are required. The
DirectDrive architecture of the MAX9727 simplifies
many circuits due to the ground-referenced outputs.
RF2
OUT_ =
RF1
(IN_ + - IN_-)
RIN1
RIN1 = RIN2, RF1 = RF2
Figure 2. Differential Input Configuration
_______________________________________________________________________________________
9
MAX9727
Shutdown Mode
The MAX9727 features a low-power shutdown mode
that reduces quiescent current consumption to less
than 0.1µA and extends battery life for portable applications. Drive SHDN low to disable the amplifiers and
the charge pump. In shutdown mode, each amplifier’s
output resistance is high impedance to small signals.
The resulting output resistance seen by the load is
determined by the series combination of the amplifier’s
external gain-setting resistors in parallel with the amplifier’s shutdown output resistance.
Inverting Amplifier Configuration
Figure 3 shows a single channel of the MAX9727 configured as an inverting amplifier. External resistors RF
and RIN set the voltage gain of the amplifier as follows:
AV =
−
RF
RIN
where AV is the desired voltage gain in V/V.
RF can be either fixed or variable, allowing the use of a
digitally controlled potentiometer to alter the gain under
software control.
Active Filter Configuration
When the MAX9727 is used as a line driver to provide
outputs that feed audio equipment (notebooks, desktops, receivers, and set-top boxes) with a digital-toanalog converter (DAC) used as an audio input source,
it is often desirable to eliminate any high-frequency
quantization noise produced by the DAC output before
it reaches the load. This high-frequency noise can
cause the input stages of the line-in equipment to
exceed slew-rate limitations or create excessive EMI
emissions on the cables between devices.
In order to suppress this noise, and to provide a 2VRMS
standard audio output level from a single 5V supply,
the MAX9727 can be configured as an active lowpass
filter. The Functional Diagram/Typical Application
Circuit shows the MAX9727 connected as 2-pole
Rauch/Multiple Feedback filter with a passband gain of
6dB and a -3dB (below passband) cutoff frequency of
approximately 27kHz (see Figure 4 for Gain vs.
Frequency plot).
Input Filter
The input capacitor CIN, in conjunction with RIN, forms
a highpass filter that removes the DC bias from an
incoming signal. The AC-coupling capacitor allows the
amplifier to bias the signal to an optimum DC level.
Assuming zero-source impedance, the -3dB point of
the highpass filter is given by:
f−3dB =
1
2πRINCIN
Setting f -3dB too high affects the low-frequency
response of the amplifier. Use capacitors with
dielectrics that have low-voltage coefficients, such as
tantalum or aluminum electrolytic. Capacitors with highvoltage coefficients, such as ceramics, can increase
distortion at low frequencies.
Charge-Pump Capacitor Selection
Use capacitors with an ESR of less than 100mΩ for
optimum performance. Low-ESR ceramic capacitors
minimize the output resistance of the charge pump. For
best performance over the extended temperature
range, select capacitors with an X7R dielectric.
ACTIVE FILTER GAIN vs. FREQUENCY
RF
MAX9727 fig04
9
6
3
MAX9727
RIN
IN_OUT_
IN_+
GAIN (dB)
MAX9727
Quad Audio Line Driver with 3VRMS Output
0
-3
-6
-9
-12
-15
1
10
100
FREQUENCY (kHz)
Figure 3. Inverting Amplifier Configuration
10
Figure 4. MAX9727 Active Filter Gain vs. Frequency
______________________________________________________________________________________
Quad Audio Line Driver with 3VRMS Output
Hold Capacitor (C2)
The hold capacitor value and ESR directly affect the
ripple at PVSS. Increasing the value of C2 reduces the
output ripple. Likewise, decreasing the ESR of C2
reduces both ripple and output resistance. Lower
capacitance values can be used in systems with low
maximum output voltage levels. See the Charge-Pump
Output Voltage vs. Output Current graphs in the Typical
Operating Characteristics. C2 should be greater than
or equal to the value of C1.
PVDD Bypass Capacitor (C3)
The PVDD bypass capacitor lowers the output impedance of the power supply and reduces the impact of
the MAX9727’s charge-pump switching transients.
Bypass PVDD with C3 and place it physically close to
PVDD and PGND. C3 should be greater than or equal to
the value of C1.
Supply Bypassing
Proper power-supply bypassing ensures low-noise,
low-distortion performance. Connect a 1µF ceramic
capacitor from VDD to PGND.
Layout and Grounding
Good PC board layout is essential for optimizing performance. Use large traces for the power-supply inputs
and amplifier outputs to minimize losses due to trace
resistance. Good grounding improves audio performance, minimizes crosstalk between channels, and
prevents any digital switching noise from coupling into
the audio signal. Route PGND and all traces that carry
switching transients away from traces and components
in the audio signal path.
Place the charge-pump capacitors (C1 and C2) as
close to the device as possible. Connect VSS and PVSS
together at capacitor C2.
Thermal-Overload Protection
Thermal-overload protection limits the total power dissipation in the MAX9727. When the junction temperature
exceeds +160°C, the thermal protection circuitry disables the amplifier output stages. The junction temperature must cool by 15°C before normal operation can
continue.
Chip Information
PROCESS: BiCMOS
______________________________________________________________________________________
11
MAX9727
Flying Capacitor (C1)
The value of the flying capacitor (C1) affects the load
regulation and the output resistance of the charge
pump. A C1 value that is too small degrades the
device’s ability to provide sufficient current drive, which
leads to a loss of output voltage. Increasing the value
of C1 improves the load regulation and reduces the
charge-pump output resistance to an extent. See the
Charge-Pump Output Voltage vs. Output Current
graphs in the Typical Operating Characteristics. Above
2.2µF, the on-resistance of the switches and the ESR of
C1 and C2 dominate.
Quad Audio Line Driver with 3VRMS Output
MAX9727
Functional Diagram/Typical Operating Circuit
15kΩ
220pF
15kΩ
220pF
2.7V TO 5.5V
1.2nF
VDD
1µF
4
MAX9727
1µF
7.5kΩ
7.5kΩ
IND- 19
1.2nF
IND+ 18
20 OUTD
OUTPUT
DAC
LINE-IN DEVICE
1kΩ
1µF
7.5kΩ
7.5kΩ
INC- 15
14 OUTC
INC+ 16
1kΩ
1µF
7.5kΩ
7.5kΩ
INB- 6
7 OUTB
INB+ 5
1.2nF
1µF
7.5kΩ
1kΩ
7.5kΩ
INA- 2
1 OUTA
INA+ 3
1.2nF
1kΩ
SHDN 8
VDD
PVDD 9
C1P 10
1µF
C1
1µF
CHARGE
PUMP
C1N 12
PGND 11
13
17
PVSS
VSS
C2
1µF
220pF
15kΩ
220pF
15kΩ
12
______________________________________________________________________________________
Quad Audio Line Driver with 3VRMS Output
QSOP.EPS
PACKAGE OUTLINE, QSOP .150", .025" LEAD PITCH
21-0055
F
1
1
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13
© 2005 Maxim Integrated Products
M. Quijano
Printed USA
is a registered trademark of Maxim Integrated Products, Inc.
MAX9727
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
工商网监
湘ICP备2023018690号
