MAX9921EVKIT+

19-4165; Rev 0; 6/08 MAX9921 Evaluation Kit Features The MAX9921 evaluation kit (EV kit) is a fully assembled and tested PCB that demonstrates the capabilities of the MAX9921 dual 2-wire Hall-effect sensor interface with diagnostics capability. The EV kit comes with the MAX9921AUB+ installed. ♦ 6V to 18V Operating Voltage Range, Survives 60V ♦ Two 2-Wire Hall-Effect Sensors on the Board ♦ Three Output Status LED Indicators ♦ Proven PCB Layout ♦ Fully Assembled and Tested Ordering Information PART TYPE MAX9921EVKIT+ EV Kit +Denotes lead-free and RoHS compliant. Component List DESIGNATION QTY DESCRIPTION C1, C3 2 0.01µF ±10%, 100V X7R ceramic capacitors (0603) TDK C1608X7R2A103K C2, C4 0 Not installed, capacitors 3 0.1µF ±10%, 100V X7R ceramic capacitors (0805) TDK C2012X7R2A104K C5, C6, C7 DESIGNATION QTY JU1, JU2 2 5-pin, 4-way headers DESCRIPTION JU3–JU7 5 2-pin headers R1 1 63.4kΩ ±1% resistor (0603) R2–R5 4 100kΩ ±5% resistors (0603) R6, R7, R8 3 240Ω ±5% resistors (0603) S1, S2 2 Hall-effect switches Allegro A1140EUA S3, S4 0 Not installed, switches 1 1µF ±10%, 25V X5R ceramic capacitor (0805) TDK C2012X5R1E105K U1 1 1 2.2µF ±10%, 100V X5R ceramic capacitor (1812) TDK C4532X7R2A225K Automotive Hall-effect interface (10 µMAX®) Maxim MAX9921AUB+ D1 1 100V, 200mA diode (SOD123) Central CMHD4448 U2 1 Automotive micropower linear regulator (6 TDFN) Maxim MAX6765TTLD2+ D2, D3 2 Green LEDs (0603) U3 1 Triple-buffer gate (8 TSSOP) 7 Shunts 1 PCB: MAX9921 Evaluation Kit+ C8 C9 D4 1 Red LED (0603) — J1 0 Not installed — Component Suppliers SUPPLIER PHONE WEBSITE Central Semiconductor Corp. 631-435-1110 www.centralsemi.com TDK Corp. 847-803-6100 www.component.tdk.com Note: Indicate that you are using the MAX9921 when contacting these component suppliers. µMAX is a registered trademark of Maxim Integrated Products, Inc. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 Evaluates: MAX9921 General Description Evaluates: MAX9921 MAX9921 Evaluation Kit Quick Start Recommended Equipment Before beginning, the following equipment is needed: • MAX9921 EV kit • One 6V to 18V DC power supply • A magnet Procedure Table 1. MAX9921 EV KIT Jumper Descriptions (JU1-JU7) JUMPER JU1, JU2 The MAX9921 EV kit is fully assembled and tested. Follow the steps below to verify board operation. Caution: Do not turn on the power supply until all connections are made. 1) Verify that all jumpers are in the default positions, as shown in Table 1. 2) Connect the DC power supply between the MAX9921 EV kit’s VBAT and GND pads. JU3 JU5 JU6 The MAX9921 EV kit board provides a proven layout for evaluating the MAX9921. The EV kit comes with MAX9921AUB+ installed. JU7 The MAX9921 is powered by a user-supplied 6V to 18V DC power supply connecting between VBAT and GND. The MAX9921 EV kit board is not reversebattery protected. During the emulation of the Hall input shorted to GND, the MAX9921 will draw substantial shorting current until the MAX9921 turns off the shorted input. The shorting current can reach a peak of 60mA to 70mA and the entire event may last 0.5µs. Many common regulatedlab power supplies will overshoot in response to a large, short-term current pulse. When evaluating the short-to-GND fault, an unregulated supply is recommended, such as a wet-cell battery. Emulates Hall input shorted to battery 1-3* Demonstrates normal operation with on-board Hall sensor 1-4 Emulates Hall input shorted to GND 1-5 Evaluates other Hall sensors Emulates the open-circuit failure 1-2* Outputs enabled Open Outputs disabled 1-2 Outputs reflect diagnostic information Open* Outputs reflect Hall sensor information JU4 Detailed Description of Hardware External Power Supply DESCRIPTION 1-2 Open 3) Turn on the DC power supply. 4) Move the magnet in front of S1 and S2. Observe the light change of the OUT1 and OUT2 LEDs on the EV kit board. POSITION 1-2* Open 1-2* Open 1-2* Open OUT1 with 100kΩ pullup OUT1 without pullup OUT2 with 100kΩ pullup OUT2 without pullup ERR with 100kΩ pullup ERR without pullup *Default position. DIAG and OE Configuration The MAX9921 EV kit uses JU3 and JU4 to configure the MAX9921 DIAG and OE inputs, as shown in Table 1. Refer to the MAX9921 IC data sheet for a detailed description of the MAX9921 diagnostic information. Outputs, Related LEDs, and Jumpers The MAX9921 EV kit has three outputs: OUT1, OUT2, and ERR. Each output has an LED to indicate its current status. All three outputs can be individually pulled up with a 100kΩ resistor, as shown in Table 1. Refer to the MAX9921 IC data sheet for a detailed description of OUT1, OUT2, and ERR outputs. Hall-Effect Sensors and Related Jumpers The MAX9921 EV kit has two Hall-effect sensors (A1140EUA). JU1 and JU2 provide a convenient way to evaluate the MAX9921 with different Hall-effect sensors and emulate different failure conditions, as shown in Table 1. 2 _______________________________________________________________________________________ MAX9921 Evaluation Kit Evaluates: MAX9921 Figure 1. MAX9921 EV Kit Schematic _______________________________________________________________________________________ 3 Evaluates: MAX9921 MAX9921 Evaluation Kit Figure 2. MAX9921 EV Kit Component Placement Guide—Component Side 4 _______________________________________________________________________________________ MAX9921 Evaluation Kit Evaluates: MAX9921 Figure 3. MAX9921 EV Kit PCB Layout—Component Side _______________________________________________________________________________________ 5 Evaluates: MAX9921 MAX9921 Evaluation Kit Figure 4. MAX9921 EV Kit PCB Layout—Solder Side Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 6 ___________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2008 Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc.