MXD1810–MXD1813/
MXD1815–MXD1818
General Description
The MXD1810–MXD1813/MXD1815–MXD1818 family of microprocessor (μP) reset circuits monitor power
supplies in μP and digital systems. These devices
provide excellent circuit reliability and low cost by
eliminating external components and adjustments when
used with +2.5V/+3.0V/+3.3V (MXD1815–MXD1818),
and +5V (MXD1810–MXD1813) systems.
These circuits assert a reset signal whenever the VCC
supply voltage declines below a preset threshold, keeping
reset asserted for at least 100ms after VCC rises above the
reset threshold. The MXD1813/MXD1818 also keep reset
asserted for at least 100ms after the output is momentarily
pulled to GND by an external pushbutton switch.
The MXD1812/MXD1817 have an active-high pushpull RESET output. The MXD1810/MXD1815 (pushpull) and MXD1811/MXD1813/MXD1816/MD1818 (opendrain) have an active-low RESET output. The open-drain
devices
(MXD1811/MXD1813/MXD1816/MXD1818)
have an internal pullup resistor to VCC. The MXD1813/
MXD1818 feature a debounced manual-reset feature that
asserts a reset if the RESET pin is pulled low for more
than 1.5μs. When used to initiate manual reset, RESET
debounces signals from devices such as mechanical
switches. For devices with this feature, the release of the
external switch triggers the reset period.
The MXD1810–MXD1813/MXD1815–MXD1818 are
guaranteed to output the correct logic state for VCC down
to +1V. These ICs provide a reset comparator designed
to ignore fast transients on VCC. Reset thresholds are
available between +2.18V and +4.62V. These
small, low-power (4μA) devices are ideal for use in
portable equipment. All are available in space-saving
3-pin SC70 and SOT23 packages, and are specified from
-40°C to +105°C.
Applications
●●
●●
●●
●●
●●
●●
Computers and Controllers
Intelligent Instruments
Set-Top Boxes
Printers
Critical μP and μC Monitoring
Portable/Battery-Powered Equipment
Low-Power μP Reset Circuits in 3-Pin
SC70/SOT23
Features
●● Precision Monitoring of +2.5V, +3V, +3.3V, and +5V
Power-Supply Voltages
●● Available in Four Reset Output Configurations
●● Factory-Set Reset Threshold Voltages: 2.18V,
2.31V, 2.55V, 2.88V, 3.06V, 4.12V, 4.37V, 4.62V
●● ±2.5% Reset Threshold Accuracy Over Temperature
●● Fixed Reset Timeout Period: 100ms (min)
●● Guaranteed RESET/RESET Valid to VCC = +1V
●● Debounced Manual-Reset Detect (MXD1813/
MXD1818)
●● Power-Supply Transient Immunity
●● No External Components
●● Low Power Consumption (4μA)
●● Pin Compatible with DS181_ Products (SOT23)
●● 3-Pin SC70 and SOT23 Packages
Ordering Information
PART†
TEMP RANGE
MXD1810UR_ _-T
-40°C to +105°C
3 SOT23
MXD1810XR_ _-T
-40°C to +105°C
3 SC70
PIN-PACKAGE
†The MXD1810–MXD1813/MXD1815–MXD1818 are available
with factory-set VCC reset thresholds from +2.18V to +3.06V
(MXD1815–MXD1818) and +4.12V to +4.62V (MXD1810–
MXD1813). Choose the desired reset-threshold suffix from the
Reset Threshold Table and insert it in place of the “_ _”
following “R” in the part number. All devices are available in
tape-and-reel only in 2500 unit increments. Other threshold
voltages may be available. Contact factory for availability.
Devices are available in both leaded and lead(Pb)-free packaging. Specify lead-free by replacing “-T” with “+T” when ordering.
Ordering Information continued at end of data sheet.
Pin Configurations
TOP VIEW
RESET
1
(RESET)
VCC 1
MXD181_U 3 GND
MXD181_X 3 GND
RESET 2
(RESET)
VCC 2
SC70-3
SOT23-3
() ARE FOR THE MXD1812/MXD1817
19-2243; Rev 2; 11/14
MXD1810–MXD1813/
MXD1815–MXD1818
Low-Power μP Reset Circuits in 3-Pin
SC70/SOT23
Absolute Maximum Ratings
VCC to GND..........................................................-0.3V to +6.0V
Push-Pull RESET (MXD1810/MXD1815),
RESET (MXD1812/MXD1817) to GND.... -0.3V to (VCC + 0.3V)
Open-Drain RESET (MXD1811/MXD1816)
to GND...............................................................-0.3V to +6.0V
Open-Drain RESET (MXD1813/MXD1818)
to GND................................................... -0.3V to (VCC + 0.3V)
Input Current (VCC, RESET)...............................................20mA
Output Current (RESET, RESET).......................................20mA
Continuous Power Dissipation (TA = +70°C)
3-Pin SC70 (derate 2.17mW above +70°C).................174mW
3-Pin SOT23 (derate 4mW/°C above +70°C)..............320mW
Operating Temperature Range .........................-40°C to +105°C
Junction Temperature......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics
(VCC = full range, TA = -40°C to +105°C, unless otherwise specified. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
Supply Voltage Range
VCC
Supply Current
ICC
Reset Threshold
VTH
Active Reset-Timeout Period
tRP
VCC to Reset Delay
tRD
Push-Button Detect to Reset
Push-Button Reset-Timeout Period
tPB
tPBRST
CONDITIONS
TA = 0°C to +105°C
TA = -40°C to +105°C
MIN
TYP
5.5
1.2
5.5
VCC = +5.5V, VCC > VTH, no load
VCC = +3.6V, VCC > VTH, no load
MAX
1.0
9
16
4
10
UNITS
V
µA
MXD181_ _ R46
4.50
4.62
4.75
MXD181_ _ R44
4.25
4.37
4.49
MXD181_ _ R41
4.00
4.12
4.24
MXD181_ _ R31
2.98
3.06
3.15
MXD181_ _ R29
2.80
2.88
2.97
MXD181_ _ R26
2.47
2.55
2.64
MXD181_ _ R23
2.25
2.31
2.37
MXD181_ _ R22
2.12
2.18
2.25
VCC rising
100
150
250
2
5
µs
VCC rising, tR = 5μs
100
150
250
ms
MXD1813/MXD1818 only
1.5
MXD1813/MXD1818 only
100
150
250
ms
VCC = (VTH + 100mV) falling to (VTH - 200mV)
V
ms
µs
TA = +25°C to +105°C
0.34
Input Low Voltage
VIL
MXD1813/MXD1818
only
Input High Voltage
VIH
MXD1813/MXD1818 only
RESET Output Source Current
IOH
VCC ≥ VTH(MAX), reset not asserted,
MXD1810/MXD1815
350
μA
RESET Output Source Current
IOH
VCC ≥ VTH(MAX), reset asserted,
MXD1812/MXD1817
350
μA
RESET Output Sink Current
IOL
VCC ≥ 2.7V, reset asserted, VOUT = 0.4V
MXD1810/MXD1811/MXD1813/MXD1815/
MXD1816/MXD1818 (Note 2)
10
mA
RESET Output Sink Current
IOL
VCC ≥ 2.7V, reset not asserted, VOUT = 0.4V
MXD1812/MXD1817
10
mA
www.maximintegrated.com
TA = -40°C to +25°C
0.15
0.7 × VCC
V
V
Maxim Integrated │ 2
MXD1810–MXD1813/
MXD1815–MXD1818
Low-Power μP Reset Circuits in 3-Pin
SC70/SOT23
Electrical Characteristics (continued)
(VCC = full range, TA = -40°C to +105°C, unless otherwise specified. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
Output High Voltage
VOH
Output Capacitance (Note 2)
COUT
Internal Pullup Resistor,
Open-Drain
CONDITIONS
0 < IOH < 500μA
MIN
TYP
VCC 0.5
VCC 0.1
3.5
5.5
MAX
UNITS
V
10
MXD1811/MXD1816
RP
7.5
MXD1813/MXD1818
3.1
5.5
7.5
Note 1: Production testing done at TA = +25°C; limits over temperature guaranteed by design.
Note 2: The MXD1811/MXD1813/MXD1816/MXD1818 have an internal pullup resistor which may deliver 1mA of sink current.
Note 3: Guaranteed by design.
pF
kΩ
Typical Operating Characteristics
(TA = +25°C, unless otherwise noted.)
VCC = +3.3V
VCC = +2.5V
0
-04
-01
144
20
50
80
TEMPERATURE (°C)
140
110
POWER-DOWN RESET DELAY
vs. TEMPERATURE
2.5
VTH = +4.62V
1.5
1.0
VTH = +2.18V
0.5
0
-40
-10
20
50
80
TEMPERATURE (°C)
www.maximintegrated.com
110
100
MAXIMUM TRANSIENT DURATION (µs)
MXD1810-13/15-18 toc04
POWER-DOWN RESET DELAY (µs)
3.0
2.0
VCC = +2.5V
148
-40
-10
20
50
80
TEMPERATURE (°C)
80
60
MXD1810-13/15-18 toc03
1.000
VTH = +2.18V
0.995
-40
-10
20
50
80
TEMPERATURE (°C)
110
OUTPUT VOLTAGE
vs. OUTPUT SINK CURRENT
MAXIMUM TRANSIENT DURATION
vs. RESET THRESHOLD OVERDRIVE
90
70
VTH = +4.62V
0.990
110
MXD1810-13/15 toc05
2
152
1.005
RESET OCCURS
ABOVE THIS LINE
50
40
30
20
200
MXD1810-13/15-18 toc06
4
VCC = +5V
NORMALIZED RESET THRESHOLD
6
156
NORMALIZED RESET THRESHOLD
vs. TEMPERATURE (VCC FALLING)
1.010
OUTPUT VOLTAGE (mV)
VCC = +5V
8
160
TIMEOUT PERIOD (ms)
RESET/RESET NOT ASSERTED
MXD1810-13/15-18 toc01
SUPPLY CURRENT (µA)
10
MXD1810-13/15-18 toc02
RESET TIMEOUT PERIOD
vs. TEMPERATURE (VCC RISING)
SUPPLY CURRENT vs. TEMPERATURE
160
120
80
40
10
0
10
100
1000
RESET THRESHOLD OVERDRIVE, VTH - VCC (mV)
0
0
3
6
9
12
OUTPUT CURRENT (mA)
15
Maxim Integrated │ 3
MXD1810–MXD1813/
MXD1815–MXD1818
Low-Power μP Reset Circuits in 3-Pin
SC70/SOT23
Typical Operating Characteristics (continued)
(TA = +25°C, unless otherwise noted.)
OUTPUT VOLTAGE
vs. OUTPUT SOURCE CURRENT
VCC - VOUT (V)
0.3
0.2
VCC = +5.5V
0.6
0.4
VCC = +2.2V
0.1
0
0
0.5
1.0
1.5
2.5
2.0
OUTPUT CURRENT (mA)
3.0
MXD1810-13/15 toc08
0.4
0.8
INPUT LOW VOLTAGE (V)
MXD1810-13/15-18 toc07
0.5
INPUT LOW VOLTAGE
vs. VCC AND TEMPERATURE
0.2
-40
-10
20
50
80
TEMPERATURE (°C)
110
Pin Descriptions
MXD1810/MXD1815
PIN
NAME
SC70
SOT23
2
1
RESET
1
2
3
3
VCC
GND
FUNCTION
Push-Pull, Active-Low Reset Output. RESET changes from high to low when VCC drops
below the selected reset threshold. RESET remains low for the reset timeout period after
VCC exceeds the device reset threshold.
Supply Voltage and Input for Reset-Threshold Monitor
Ground
MXD1811/MXD1816
PIN
NAME
SC70
SOT23
2
1
RESET
1
2
3
3
VCC
www.maximintegrated.com
GND
FUNCTION
Open-Drain, Active-Low Reset Output. RESET changes from high to low when VCC drops
below the selected reset threshold. RESET remains low for the reset timeout period after
VCC exceeds the device reset threshold. RESET has an internal 5.5kΩ pullup resistor.
Supply Voltage and Input for Reset-Threshold Monitor
Ground
Maxim Integrated │ 4
MXD1810–MXD1813/
MXD1815–MXD1818
Low-Power μP Reset Circuits in 3-Pin
SC70/SOT23
Pin Description (continued)
MXD1812/MXD1817
PIN
SC70
SOT23
2
1
1
2
3
3
NAME
RESET
VCC
GND
FUNCTION
Push-Pull, Active-High Reset Output. RESET changes from low to high when VCC drops
below the selected reset threshold. RESET remains high for the reset timeout period after
VCC exceeds the device reset threshold.
Supply Voltage and Input for Reset- Threshold Monitor
Ground
MXD1813/MXD1818
PIN
SC70
NAME
SOT23
2
1
RESET
1
2
3
3
VCC
GND
FUNCTION
Open-Drain, Active-Low Reset Output with Manual Reset Detect. RESET changes from
high to low when VCC drops below the selected reset threshold, or RESET is externally
pulled low for at least 1.5μs. RESET remains low for the reset timeout period after VCC
exceeds the device reset threshold or after the external manual reset is released. RESET
has an internal 5.5kΩ pullup resistor.
Supply Voltage and Input for Reset-Threshold Monitor
Ground
Detailed Description
RESET/RESET Output
A microprocessor’s (μP’s) reset input starts the microprocessor in a known state. The MXD1810–MXD1813/
MXD1815–MXD1818 μP supervisory circuits assert reset
to prevent code-execution errors during power-up, powerdown, and brownout conditions (Figure 4). Whenever
VCC falls below the reset threshold, the reset output
asserts. Once VCC exceeds the reset threshold, an
internal timer keeps the reset output asserted for the
specified reset timeout period (tRP). Reset is also
triggered by an externally initiated rising edge on the
RESET pin (MXD1813/MXD1818), following a low signal
of 1.5μs minimum duration.
Push-Button Reset (MXD1813/MXD1818)
Many μP-based products require push-button reset
capability (Figure 5), allowing the operator, a test
technician, or external logic circuitry to initiate reset.
On the MXD1813/MXD1818, a logic-low on RESET
held for greater than 1.5μs asserts a reset. RESET
deasserts following a 100ms minimum reset timeout
www.maximintegrated.com
delay (tPBRST). A manual-reset input shorter than 1.5μs
may release RESET without the 100ms minimum reset
timeout delay. To facilitate use with mechanical switches,
the MXD1813/MXD1818 contain internal debouncing
circuitry. A debounced waveform is shown in Figure 6.
Applications Information
Interfacing to μPs with Bidirectional
Reset Pins
Since the RESET output on the MXD1811/MXD1816
is open drain, these devices interface easily with μPs
that have bidirectional reset pins, such as the Motorola
68HC11. Connecting the μP supervisor’s RESET output
directly to the microcontroller’s (μC’s) RESET pin allows
either device to assert reset (Figure 7). No external pullup
resistor is required, as it is contained within the MXD1811/
MXD1816.
Negative-Going VCC Transients
In addition to issuing a reset to the μP during power-up,
power-down, and brownout conditions, these devices are
relatively immune to short-duration, negative-going VCC
transients (glitches).
Maxim Integrated │ 5
MXD1810–MXD1813/
MXD1815–MXD1818
Low-Power μP Reset Circuits in 3-Pin
SC70/SOT23
Functional Diagram
MXD1810
MXD1812
MXD1815
MXD1817
VCC
MXD1811
MXD1816
VCC
RESET
RESET
GENERATOR
VREF
VREF
Figure 1. Functional Diagram, Push-Pull Output
Figure 2. Functional Diagram, Open-Drain Active-Low Output
The Typical Operating Characteristics show the Maximum
Transient Duration vs. Reset Threshold Overdrive for
which reset pulses are not generated. The graph shows
the maximum pulse width that a negative-going VCC
transient may typically have without issuing a reset signal.
As the amplitude of the transient increases, the maximum
allowable pulse width decreases.
MXD1813
MXD1818
VCC
Ensuring a Valid Reset Output Down to
VCC = 0
MR
MONITOR
RESET
GENERATOR
RESET
VREF
Figure 3. Functional Diagram, Open-Drain Active-Low Output
with Manual Reset Detection
www.maximintegrated.com
RESET
GENERATOR
RESET
OR
RESET
When VCC falls below the minimum operating voltage,
push-pull-structured reset sinking (or sourcing) capabilities decrease dramatically. High-impedance CMOSlogic
inputs connected to the RESET/RESET pin can drift to
indeterminate voltages. This does not present a problem
in most cases, since most μPs and circuitry do not operate
at VCC below +1V. For MXD1810/MXD1815 applications
where RESET must be valid down to VCC = 0, adding
a pulldown resistor between RESET and GND removes
stray leakage currents, holding RESET low (Figure 8).
The pulldown resistor value is not critical; 100kΩ is large
enough not to load RESET and small enough to pull
RESET low. For MXD1812/ MXD1817 applications where
Maxim Integrated │ 6
MXD1810–MXD1813/
MXD1815–MXD1818
Low-Power μP Reset Circuits in 3-Pin
SC70/SOT23
VCC
VCC
VTH
MXD1813
MXD1818
VCC
tRP
RESET
RESET
VCC(MIN)
GND
RESET
MANUAL
RESET
tRP
RESET
Figure 4. Power-Up Reset Timing Diagram
Figure 5. Push-Button Manual Reset
VCC
tPBRST
tPBRST
(OPEN)
SWITCH BOUNCE
EXTERNAL
PUSH BUTTON
(CLOSED)
RESET
Figure 6. Manual Reset Timing Diagram
RESET must be valid to VCC = 0, a 100kΩ pullup resistor
between RESET and VCC holds RESET high when VCC
falls below the minimum operating voltage (Figure 9).
The MXD1811/MXD1813/MXD1816/MXD1818 have
open-drain, active-low outputs with a pullup resistor
included internal to the devices. While using these
devices, RESET will most likely not maintain an active
www.maximintegrated.com
condition when the supply voltage drops below the
minimum VCC, but will drift to a nonactive level due to
the pullup resistor and the reduced sinking capability of
the open-drain output. Therefore, these devices are not
recommended for applications where the RESET pin is
required to be valid at VCC = 0.
Maxim Integrated │ 7
MXD1810–MXD1813/
MXD1815–MXD1818
Low-Power μP Reset Circuits in 3-Pin
SC70/SOT23
Table 1. Device Marking Codes
VCC
PART
VCC
VCC
MXD1811
MXD1816
RESET
µP
RESET
GND
GND
RPULLDOWN*
AHT
FZKF
AHW
MXD1811_R44
FZIW
AEL
MXD1811_R41
FZKE
AHV
FZIX
AEM
MXD1813_R46
FZIY
AEN
MXD1813_R44
FZKJ
AIA
MXD1813_R41
FZKI
AHZ
MXD1815_R31
FZKN
AIE
MXD1815_R29
FZIZ
AEO
MXD1815_R26
FZKM
AID
MXD1815_R23
FZKL
AIC
MXD1815_R22
FZKK
AIB
µP
MXD1816_R31
FZKR
AII
MXD1816_R29
FZKQ
AIH
GND
MXD1816_R26
FZKP
AIG
MXD1816_R23
FZKO
AIF
MXD1816_R22
FZJA
AEP
MXD1817_R31
FZJB
AEQ
MXD1817_R29
FZKV
AIM
MXD1817_R26
FZKU
AIL
MXD1817_R23
FZKT
AIK
MXD1817_R22
FZKS
AIJ
VCC
VCC
RESET
FZKC
MXD1811_R46
MXD1812_R41
VCC
RESET
MXD1810_R41
AHY
Figure 8. Ensuring Valid RESET Output Down to VCC = 0
(MXD1810/MXD1815 only)
MXD1812
MXD1817
AHU
AHX
*MXD1810/MXD1815 ONLY
RPULLUP*
FZKD
FZKH
VCC
GND
AEK
MXD1810_R44
FZKG
VCC
RESET
FZIV
MXD1812_R44
VCC
RESET
SC70
MXD1810_R46
MXD1812_R46
Figure 7. Interfacing to Microprocessors with Bidirectional
Reset Pins
MXD1810
MXD1815
TOP MARK
SOT23
MXD1818_R31
FZKY
AIP
MXD1818_R29
FZKX
AIO
MXD1818_R26
FZJC
AER
MXD1818_R23
FZKW
AIN
MXD1818_R22
FZJE
AEV
µP
GND
GND
*MXD1812/MXD1817 ONLY
Figure 9. Ensuring Valid RESET Output Down to VCC = 0
(MXD1812/MXD1817 only)
www.maximintegrated.com
Maxim Integrated │ 8
MXD1810–MXD1813/
MXD1815–MXD1818
Low-Power μP Reset Circuits in 3-Pin
SC70/SOT23
Selector Guide
PUSH-PULL
RESET
OPEN-DRAIN
RESET
PUSH-PULL
RESET
OPEN-DRAIN
RESET WITH
PUSHBUTTON
DETECT
PART
5V SYSTEMS
2.5V/3.0V/3.3V
SYSTEMS
MXD1810
✔
—
✔
—
—
—
MXD1811
✔
—
—
✔
—
—
MXD1812
✔
—
—
—
✔
—
MXD1813
✔
—
—
—
—
✔
MXD1815
—
✔
—
—
—
MXD1816
—
✔
✔
—
✔
—
—
MXD1817
—
✔
—
—
✔
—
—
✔
—
—
—
✔
MXD1818
Ordering Information (continued)
PART†
TEMP RANGE
MXD1811UR_ _-T
-40°C to +105°C
3 SOT23
MXD1811XR_ _-T
-40°C to +105°C
MXD1812UR_ _-T
-40°C to +105°C
MXD1812XR_ _-T
MXD1813UR_ _-T
PIN-PACKAGE
Reset Threshold Table
PART
SUFFIX
(_ _)
TYP. RESET
THRESHOLD (V)*
3 SC70
MXD1810–MXD1813
46
4.62
3 SOT23
MXD1810–MXD1813
44
4.37
-40°C to +105°C
3 SC70
MXD1810–MXD1813
41
4.12
-40°C to +105°C
3 SOT23
MXD1815–MXD1818
31
3.06
MXD1813XR_ _-T
-40°C to +105°C
3 SC70
MXD1815–MXD1818
29
2.88
MXD1815UR_ _-T
-40°C to +105°C
3 SOT23
MXD1815–MXD1818
26
2.55
MXD1815XR_ _-T
-40°C to +105°C
3 SC70
MXD1815–MXD1818
23
2.31
MXD1816UR_ _-T
-40°C to +105°C
3 SOT23
MXD1815–MXD1818
22
2.18
MXD1816XR_ _-T
-40°C to +105°C
3 SC70
MXD1817UR_ _-T
-40°C to +105°C
3 SOT23
MXD1817XR_ _-T
-40°C to +105°C
3 SC70
MXD1818UR_ _-T
-40°C to +105°C
3 SOT23
MXD1818XR_ _-T
-40°C to +105°C
3 SC70
†The MXD1810–MXD1813/MXD1815–MXD1818 are available
with factory-set VCC reset thresholds from +2.18V to +3.06V
(MXD1815–MXD1818) and +4.12V to +4.62V (MXD1810–
MXD1813). Choose the desired reset-threshold suffix from the
Reset Threshold Table and insert it in place of the “_ _”
following “R” in the part number. All devices are available in
tape-and-reel only in 2500 unit increments. Other threshold
voltages may be available. Contact factory for availability.
Devices are available in both leaded and lead(Pb)-free
packaging. Specify lead-free by replacing “-T” with “+T”
when ordering.
www.maximintegrated.com
*Factory-trimmed reset thresholds are nominally ±1.5% at
room temperature.
Chip Information
PROCESS TECHNOLOGY: BiCMOS
Package Information
For the latest package outline information and land patterns
(footprints), go to www.maximintegrated.com/packages. Note
that a “+”, “#”, or “-” in the package code indicates RoHS status
only. Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
3 SC70
X3-2
21-0075
90-0208
3 SOT23
U3-1
21-0051
90-0179
Maxim Integrated │ 9
MXD1810–MXD1813/
MXD1815–MXD1818
Low-Power μP Reset Circuits in 3-Pin
SC70/SOT23
Revision History
REVISION
NUMBER
REVISION
DATE
PAGES
CHANGED
1
12/05
Miscellaneous updates
2
11/14
No /V OPN in Ordering Information, removed automotive reference from
Applications section; updated Packaging Information
DESCRIPTION
1,9-11
1, 10, 11
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits)
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
© 2014 Maxim Integrated Products, Inc. │ 10
工商网监
湘ICP备2023018690号
