1518-100-22IN

1518 5-TAP SMD DELAY LINE TD/TR = 3 (SERIES 1518) FEATURES • • • • • 5 taps of equal delay increment Delays to 200ns Low profile Epoxy encapsulated Meets or exceeds MIL-D-23859C IN N/C T2 N/C T4 T5 GND 1 2 3 4 5 6 7 14 13 12 11 10 9 8 N/C T1 N/C T3 N/C N/C N/C data 3 ® delay devices, inc. PACKAGES IN Signal Input T1-T5 Tap Outputs GND Ground Note: Standard pinout shown Alt. pinout available FUNCTIONAL DESCRIPTION The 1518-series device is a fixed, single-input, fiveoutput, passive delay line. The signal input (IN) is reproduced at the outputs (T1-T5) in equal increments. The delay from IN to T5 (TD) and the characteristic impedance of the line (Z) are determined by the dash number. The rise time (TR) of the line is 30% of TD, and the 3dB bandwidth is given by 1.05 / TD. The device is available in a 14-pin SMD with two pinout options. Part numbers are constructed according to the scheme shown at right. For example, 1518-101-500A is a 100ns, 50Ω delay line with pinout code A. Similarly, 1518-151501 a is 150ns, 500Ω delay line with standard pinout. PART NUMBER CONSTRUCTION 1518 - xxx - zzz p DELAY TIME Expressed in nanoseconds (ns) First two digits are significant figures Last digit specifies # of zeros to follow IMPEDANCE Expressed in nanoseconds (ns) First two digits are significant figures Last digit specifies # of zeros to follow PINOUT CODE See Table Omit for STD pinout SERIES SPECIFICATIONS • • • • • Dielectric breakdown: Distortion @ output: Operating temperature: Storage temperature: Temperature coefficient: 50 Vdc 10% max. -55°C to +125°C -55°C to +125°C 100 PPM/°C TD (ns) 5 10 15 20 25 30 40 50 60 75 80 100 110 125 150 180 200 DELAY SPECIFICATIONS TI (ns) 1.0 2.0 3.0 4.0 5.0 6.0 8.0 10.0 12.0 15.0 16.0 20.0 22.0 25.0 30.0 36.0 50.0 TR (ns) 3.0 4.0 5.0 6.0 7.0 10.0 13.0 15.0 20.0 25.0 26.0 30.0 32.0 40.0 50.0 60.0 70.0 Z=50Ω N/A 3 3 3 3 3 3 3 3 3 4 4 4 4 N/A N/A N/A ATTENUATION (%) TYPICAL Z=100Ω Z=200Ω Z=300Ω Z=500Ω 5 N/A N/A N/A 5 5 N/A N/A 5 5 N/A N/A 5 5 5 N/A 5 5 5 7 5 5 5 7 5 5 5 7 5 5 7 7 5 6 7 8 5 6 7 8 5 6 7 8 5 6 7 8 5 6 7 8 5 6 7 8 5 8 10 10 7 8 10 10 8 10 12 12 T1 T2 T3 T4 IN GND T5 GND Functional Diagram .018 .505 .050 .185 14 8 Notes: TI represents nominal tap-to-tap delay increment Tolerance on TD = ±5% or ±2ns, whichever is greater Tolerance on TI = ±5% or ±1ns, whichever is greater “N/A” indicates that delay is not available at this Z .425 .290 1 7 PINOUT CODES CODE STD A IN 1 1 T1 13 12 T2 3 4 T3 11 10 T4 5 6 T5 6 7 GND 7 8,14 .300 .100 Package Dimensions ©1997 Data Delay Devices Doc #97030 2/7/97 DATA DELAY DEVICES, INC. 3 Mt. Prospect Ave. Clifton, NJ 07013 1 1518 PASSIVE DELAY LINE TEST SPECIFICATIONS TEST CONDITIONS 25oC ± 3oC High = 3.0V typical Low = 0.0V typical Source Impedance: 50Ω Max. Rise/Fall Time: 3.0 ns Max. (measured at 10% and 90% levels) Pulse Width (TD 75ns): PERIN = 10 x TD INPUT: Ambient Temperature: Input Pulse: OUTPUT: Rload: Cload: Threshold: 10MΩ 10pf 50% (Rising & Falling) NOTE: The above conditions are for test only and do not in any way restrict the operation of the device. PERIN PWIN TRISE INPUT SIGNAL 90% 50% 10% TFALL VIH 90% 50% 10% VIL TFALL TRISE TRISE OUTPUT SIGNAL 90% 50% 10% TFALL VOH 90% 50% 10% VOL Timing Diagram For Testing OUT PULSE GENERATOR TRIG RIN IN DEVICE UNDER TEST (DUT) 50 Ω T1 T2 T3 T4 T5 IN TRIG OSCILLOSCOPE RIN = ROUT = ZLINE ROUT Test Setup Doc #97030 2/7/97 DATA DELAY DEVICES, INC. Tel: 973-773-2299 Fax: 973-773-9672 http://www.datadelay.com 2