BTP-187WHCQ-XX-30

BriLux 1W Light Source BTP-187XXCQ-XX-XX Package Dimension [Note 1] Features Highest Lumen Per Watt Long Operational Life More Energy Efficient IC Compatible Low DC Voltage Superior ESD Protection Smallest Footprint Applications Accent Lighting Automotive Exterior/Interior Light High Power Back Light Reading Light Marine/Miner ’s Lighting Portable Lighting Tolerance: ± see spec Unit: ± mm Optical Characteristics at Ta=25ºC, IF=350mA PART NUMBER LED CHIP MATERIAL Lens Color Water Clear Water Clear Water Clear Water Clear Water Clear Water Clear Wavelength/CCT Range (nm/K) Drive Voltage Luminous VIEW ANGLE Flux @350mA(lm) 2θ1/2 Typ. 17 lm[2] 17 lm [2] Min/Max 620~635 585~595 460~470 470~480 520~530 3000K 8000K Typ. 2.60V 2.60V 3.60V 3.60V 3.60V 3.60V (deg) BTP-187NRCQ-XX-17 BTP-187YECQ-XX-17 BTP-187BLCQ-XX-08 BTP-187GBCQ-XX-10 BTP-187PGCQ-XX-15 BTP-187WHCQ-XX-30 Note: 1) Picture for illustration purpose only. AlInGaP AlInGaP AlInGaN AlInGaN AlInGaN AlInGaN 90 90 90 90 90 90 6 lm[2] 10 lm 15lm [2] [2] 30 lm[2] Please refer to outline dimension for actual package size. 2) Due to the CIE eye response curve in the wavelength range, the minimum luminous flux will vary over the wavelength range of λD. For example, luminous flux will vary from a minimum of 4.5lm at 460 to a typical of 15 lm at 480nm nm due to this effect. DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com BriLux 1W Light Source BTP-187XXCQ-XX-XX Absolute Maximum Ratings at Ta=25ºC Parameter Red/Yellow White/Blue DC Forward Current (mA)[1] Peak Pulsed Forward Current (mA) Average Forward Current (mA) Reverse Voltage (V) LED Junction Temperature (°C) [3] Thermal Resistance without heatsink (°C/W) Storage Temperature (°C) Operating Temperature (°C) 300 350 300 5 120 80 -20 to +80 -10 to +70 350 500 300 5 120 80 -20 to +80 -10 to +70 Application Notes: 1. 2. 3. Proper forward current must be observed to maintain the junction temperature below maximum rating Although all products listed are class one ESD protection (+/- 1KV by HBM mode), care must be fully taken when handling products Specification is subjected to change for improvements without notice. DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com BriLux 1W Light Source BTP-187XXCQ-XX-XX Typical Electro-Optical Characteristics Curves at Ta=25ºC DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com BriLux 1W Light Source BTP-187XXCQ-XX-XX Recommended Soldering Pattern Important Notes: The information contained herein is presented only as a Guide for the application of our products. Brilliance Technologies assumes no responsibility for any infringement of intellectual property or other rights of the third parties w hich may result from its use. Brilliance Technologies continually improves the quality of our products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsible of the customer, w hen using Brilliance Technologies products, to comply w ith the standard of safety in making a safe design for the entire system, and to avoid situations in w hich a malfunction or failure of such Brilliance Technologies products cause loss of human life, bodily injury or damage to property. Brilliance Technologies products listed in this data sheet are intended for usage in general electronics and/or non-commercial or industrial lighting products. These products are neither intended nor w arranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of w hich may cause loss of human life or bodily injury. In developing your design, please ensure that Brilliance Technologies products are used w ithin specified operating ranges as set forth in the most recent Brilliance Technologies data sheets. BT-Rev. 1.0B20040917 Specifications are subject to change for improvement without notice. Copyright © 2003 Brilliance Technologies Co., Ltd. All rights reserved. DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com